TENDA TENDA NOVA MW3-3 Instructions

Package contents

Mesh3f x 3 Ethernet cable x 1

Power adapter x 3 Quick installation guide x 1

Know your device

RST PWRLANWAN/LAN

RST button

WAN/LAN port

LAN port

DC power jack

Install the Tenda WiFi App

Ⅰ

Download the Tenda WiFi App on your mobile device by
searching for Tenda WiFi in App Store or Google Play or by
scanning the QR code. Then, install the App.

Available for iOS and Android

Or

TendaWiFi

Connect the primary node

Ⅱ

*The first node you set up functions as the primary node,
while the rest are referred to as the secondary node.

Internet

DSL

WAN

Modem

WAN/LAN

RST PWRLANWAN/LAN

Or

Ethernet jack

1. Power off your modem, and remove and reinstall its
battery (if any).

2. Use the included Ethernet cable to connect a LAN port
of your modem or the Ethernet jack to the WAN/LAN port
of any node. This node is your primary node.

3. Power on your modem.

4. Use one of the included power adapters to connect the
primary node to a power source, the LED indicator lights
solid on. Wait about for 40 seconds. The system completes
startup when the LED indicator blinks green.

Connect the primary node to

Ⅲ

the internet

1. Go to the WiFi network list on your mobile device,
select the SSID of the primary node, and enter its
password. The SSID and password are specified
on the bottom label of any node.

AC1200 Whole Home Mesh WiFi System

Model: Mesh3f
Power: 9V 1A
FCC ID: V7TMESH 3F
IC: 9034A-MESH 3F
MAC:
SN:

Settings

Wi-Fi

NOVA_ XXXX

CHOOSE A NETWORK...

XXX XXX

2. Run the Tenda WiFi App and follow the onscreen
instructions to connect the primar y node to the
internet.
After the primary node is connected to the internet,
its LED indicator lights solid green.

Wi-Fi

SSID:
NOVA_X XXX
Passw ord:

Connect secondary nodes to

Ⅳ

the internet

1. Place each node:

- At a high and open area within the network coverage
of connected node;

- Keep your nodes away from electronics with strong
interference, such as microwave oven, induction
cooker and refrigerator.

2. Use the other included power adapters to connect the
remaining secondary nodes to power sources, their LED
indicators light solid green. Wait about for 40 seconds.
The secondary node is connecting to another node when
its LED indicator blinks green.

3. Observe the LED indicator of the secondary nodes until
their LED indicators light one of the following colors:

Solid green Good connection

Solid yellow Fair connection

Solid red Disconnected

4. If a node's LED indicator does not light solid green, move your
nodes according to step 1 in get it better connected.

Ⅳ

Done. To access the internet:

- Wired devices: Connect wired devices to the LAN ports of your
nodes.

- Wireless devices: Connect wireless devices to your WiFi
network using the SSID and WiFi password you set.

- If you want to manage the network anytime anywhere, tap
and use your account to login.

FAQ

Q1: How can I change my SSID and password?

A1: Run Tenda WiFi App, tap Settings in the lower-right corner,
tap Wireless Settings, change your SSID and password, and
tap Save. Then, you need to reconnect your mobile devices
using the new SSID and password.

Q2: How can I remove a node from my WiFi network?

A1: Tap the node on the Tenda WiFi App, tap ... in the upper-right
corner, and choose Delete.
Note: Removing operation restores the node to factory
settings.

Q3: Can I add another new set of node to expand my network
coverage?

A3: Yes. Open Tenda WiFi App, tap Settings in the lower-right
corner, tap Add Nova, and follow the on-screen instructions
to add.

Q4: How to restore my network to factory settings?

A4: With your nodes powered on, hold the RST button of your
primary node down using a paper clip for about 6 seconds,
release when the LED indicator blinks fast. Your network is
reset successfully when the LED indicator lights solid on
then blinks fast again. And all nodes are restored to factory
settings.

CE Mark Warning

This is a Class B product. In a domestic environment, this product may
cause radio interference, in which case the user may be required to take
adequate measures.
Operations in the 5.15-5.25GHz band are restricted to indoor use only.
This equipment should be installed and operated with minimum distance
20cm between the radiator & your body.

NOTE: (1) The manufacturer is not responsible for any radio or TV
interference caused by unauthorized modifications to this
equipment.
(2) To avoid unnecessary radiation interference, it is recommended
to use a shielded RJ45 cable.

Declaration of Conformity

Hereby, SHENZHEN TENDA TECHNOLOGY CO., LTD. declares that the radio
equipment type Mesh3f is in compliance with Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the
following internet address:
http://www.tendacn.com/en/service/download-cata-101.html

Operate Frequency:

2.4 GHz: EU/2400-2483.5MHz (CH1-CH13)
5 GHz: EU/5150-5250MHz (CH36-CH48)

EIRP Power (Max.):

2.4 GHz: 19.67dBm
5 GHz: 22.21dBm
Software Version: V1.0.0.X

For EU/EFTA, this product can be used in the following countries:

FCC Statement

This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communicat ions.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct t he
interference by one or more of the following measures:

— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.

The device is for indoor usage only.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.

This device complies with FCC radiation exposure limits set forth for an
uncontrolled environment and it also complies with Part 15 of the FCC RF
Rules.

This equipment should be installed and operated with minimum distance
20cm between the radiator & your body.

Caution:

Any changes or modifications not expressly approved by the part y
responsible for compliance could void the user's authorit y to operate this
equipment.
This transmitter must not be co-located or operating in conjunction with
any other antenna or transmitter.

NOTE:

(1) The manufacturer is not responsible for any radio or TV interference
caused by unauthorized modifications to this equipment. (2) To avoid
unnecessary radiation interference, it is recommended to use a shielded
RJ45 cable.

Adapter Model:

BN052-A09009U/BN052-A09009E/BN052-A09009B/BN052-A09009P1

Input: 100-240V~ 50/60Hz 0.3A
Output: 9V DC, 1A
Manufacturer: SHENZHEN HEWEISHUN NETWORK TECHNOLOGY CO., LTD.
: DC Voltage

Operating Environment

Temperature: 0°C-40°C Humidity: (10 - 90)% RH, non-condensing

This product bears the selective sorting symbol for Waste electr ical and
electronic equipment (WEEE).
This means that this product must be handled pursuant to European
directive 2012/19/EU in order to be recycled or dismantled to minimize its
impact on the environment.
User has the choice to give his product to a competent recycling
organization or to the retailer when he buys new electrical or electronic
equipment.

Caution:

RECYCLING

Technical Support

Shenzhen Tenda Technology Co., Ltd.
6-8 Floor, Tower E3, No. 1001, Zhongshanyuan Road, Nanshan
District, Shenzhen, China. 518052

USA hotline: [phone]
Toll Free: Daily-9am to 6pm EST
Canada hotline: [phone]
Toll Free: Mon - Fri 9 am - 6 pm PST
Website: http://www.tendacn.com

Hong Kong hotline: [phone]
Website: http://www.tendacn.com
Email: [e-mail]

Copyright

© 2018 Shenzhen Tenda Technology Co., Ltd. All rights reser ved.

Tenda is a registered trademark legally held by Shenzhen Tenda
Technology Co., Ltd. Other brand and product names mentioned herein
are trademarks or registered trademarks of their respective holders.
Specifications are subject to change without notice.

AC1200 Whole Home Mesh WiFi System

MW3 (3-pack)

Quick Installation Guide