Tenda I-WL-D305 User Manual

Copyright Statement

© 2015 Shenzhen Tenda Technology Co., Ltd. All rights reserved.

Tenda is a registered trademark legally held by Shenzhen Tenda Technology Co., Ltd. Other brand and product names

mentioned herein are trademarks or registered trademarks of their respective holders. Copyright of the whole product as

integration, including its accessories and software, belongs to Shenzhen Tenda Technology Co., Ltd. No part of this

publication can be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in

any form or by any means without the prior written permission of Shenzhen Tenda Technology Co., Ltd.

Disclaimer

Pictures, images and product specifications herein are for references only. To improve internal design, operational

function, and/or reliability, Tenda reserves the right to make changes to the products without obligation to notify any

person or organization of such revisions or changes. Tenda does not assume any liability that may occur due to the use or

application of the product described herein. Every effort has been made in the preparation of this document to ensure

accuracy of the contents, but all statements, information and recommendations in this document do not constitute the

warranty of any kind, express or implied.

Technical Support

Technical Support: [e-mail]

Telephone: [phone]

Email: [e-mail]

Website: http://www.tendacn.com

Skype: tendasz

YouTube: Tendasz1999

i

Copyright Statement

© 2015 Shenzhen Tenda Technology Co., Ltd. All rights reserved.

Tenda is a registered trademark legally held by Shenzhen Tenda Technology Co., Ltd. Other brand and product names

mentioned herein are trademarks or registered trademarks of their respective holders. Copyright of the whole product as

integration, including its accessories and software, belongs to Shenzhen Tenda Technology Co., Ltd. No part of this

publication can be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in

any form or by any means without the prior written permission of Shenzhen Tenda Technology Co., Ltd.

Disclaimer

Pictures, images and product specifications herein are for references only. To improve internal design, operational

function, and/or reliability, Tenda reserves the right to make changes to the products without obligation to notify any

person or organization of such revisions or changes. Tenda does not assume any liability that may occur due to the use or

application of the product described herein. Every effort has been made in the preparation of this document to ensure

accuracy of the contents, but all statements, information and recommendations in this document do not constitute the

warranty of any kind, express or implied.

ii

Contents

Shortcut to Common Function Setup ......................................................................................................................................... v

Chapter 1 Product Overview ....................................................................................................................................................... 1

1.1 What It Does ........................................................................................................................................................................ 1

1.2 Product Features ................................................................................................................................................................... 1

1.3 Package Contents ................................................................................................................................................................. 2

1.4 Front Panel ........................................................................................................................................................................... 3

1.5 Back Panel............................................................................................................................................................................ 4

Chapter 2 Hardware Installation ................................................................................................................................................ 5

2.1 DSL Access .......................................................................................................................................................................... 5

2.2 Ethernet Access .................................................................................................................................................................... 7

Chapter 3 Internet Setup ............................................................................................................................................................. 9

3.1 Log in to UI (User Interface)................................................................................................................................................ 9

3.2 Set up Internet .................................................................................................................................................................... 10

About Link Type .................................................................................................................................................................. 10

About Connection Type ....................................................................................................................................................... 10

Internet Setup Instruction ..................................................................................................................................................... 11

3.3 Quick Wireless Security Setup ........................................................................................................................................... 18

Chapter 4 Advanced Settings .................................................................................................................................................... 19

4.1 Device Info ......................................................................................................................................................................... 19

4.2 Advanced Setup .................................................................................................................................................................. 22

4.2.1 Layer2 Interface .......................................................................................................................................................... 23

4.2.2 WAN Service .............................................................................................................................................................. 25

4.2.3 LAN Setup .................................................................................................................................................................. 79

4.2.4 NAT ............................................................................................................................................................................. 82

4.2.5 Security ....................................................................................................................................................................... 87

4.2.6 Parental Control .......................................................................................................................................................... 90

4.2.7 Bandwidth Control ...................................................................................................................................................... 93

4.2.8 Routing ........................................................................................................................................................................ 94

4.2.9 DNS ............................................................................................................................................................................ 96

4.2.10 DSL ........................................................................................................................................................................... 99

4.2.11 Storage Service ........................................................................................................................................................ 100

4.2.12 Interface Grouping .................................................................................................................................................. 103

4.2.13 IP Tunnel ................................................................................................................................................................. 105

4.2.14 Certificate ................................................................................................................................................................ 106

4.2.15 Multicast ................................................................................................................................................................. 109

4.2.16 IPTV ........................................................................................................................................................................ 111

4.3 Wireless ............................................................................................................................................................................ 112

4.3.1 Basic.......................................................................................................................................................................... 112

4.3.2 Security ..................................................................................................................................................................... 113

4.3.3 MAC Filter ................................................................................................................................................................ 116

4.3.4 Wireless Bridge ......................................................................................................................................................... 117

4.3.5 Station Info ................................................................................................................................................................ 125

4.4 Diagnostics ................................................................................................................................................................ 125

iii

4.4.1 Diagnostics ................................................................................................................................................................ 126

4.4.2 Ping test ..................................................................................................................................................................... 126

4.5 Management ..................................................................................................................................................................... 127

4.5.1 Settings ...................................................................................................................................................................... 127

4.5.2 System Logs .............................................................................................................................................................. 128

4.5.3 SNMP Agent ............................................................................................................................................................. 129

4.5.4 TR-069 Client ........................................................................................................................................................... 130

4.5.5 Internet Time ............................................................................................................................................................. 131

4.5.6 Access Control .......................................................................................................................................................... 132

4.5.7 Update Software ........................................................................................................................................................ 133

4.5.8 Reboot ....................................................................................................................................................................... 136

Appendix 1 Applications .......................................................................................................................................................... 137

Application 1: How to change SSID and wireless password? ................................................................................................ 137

Application 2: How to reset the modem router? .................................................................................................................... 138

Method 1: WPS/RST button .............................................................................................................................................. 138

Method 2: Restore Default Settings from User Interface ................................................................................................... 138

Appendix 2 Configure Your PC ............................................................................................................................................... 139

Windows 8 ............................................................................................................................................................................. 139

Windows 7 ............................................................................................................................................................................. 141

MAC ...................................................................................................................................................................................... 143

Appendix 3 Join Your Wireless Network ................................................................................................................................ 144

Windows 8 ............................................................................................................................................................................. 144

Windows 7 ............................................................................................................................................................................. 145

MAC ...................................................................................................................................................................................... 146

iPhone/iPad ............................................................................................................................................................................ 147

Appendix 4 FAQs ..................................................................................................................................................................... 148

Appendix 5 VPI/VCI List ........................................................................................................................................................ 149

Appendix 6 Regulatory Compliance Information ................................................................................................................. 165

iv

Shortcut to Common Function Setup

How to set up the Internet connection?

GO

How to change your SSID (WiFi name) and password?

GO

How to change your login username and password?

GO

How to make your kids surf the Internet safely?

GO

How to set bandwidth for a specified host or client?

GO

How to restrict a host to access your wireless network?

GO

How to access a USB storage?

GO

How to expand your wireless network coverage?

GO

How to make your set-top box available?

GO

How to reset the modem router to factory defaults?

GO

© 2015 Shenzhen Tenda Technology Co., Ltd. All rights reserved.

Technical Support: [e-mail]

Telephone: [phone]

Email: [e-mail]

Website: http://www.tendacn.com

Skype: tendasz

YouTube: Tendasz1999

v

Chapter 1 Product Overview

Get to know your modem router overall. This part includes the following:

1.1 What It Does

1.2 Product Features

1.3 Package Contents

1.4 Front Panel

1.5 Back Panel

1.1 What It Does

The Wireless ADSL2+ Modem Router, integrated with functions of ADSL2+ modem and wireless router, is especially

designed for ordinary home users. So it supports telephone cable access and

Ethernet cable access. Up to 300M wireless speed (fluently play file

transfers, streaming HD video, and multiplayer gaming) can match the

family requests perfectly. The auto-detecting link type and PVC make you

set up the modem router quickly and easily. More advanced features, like

Parental Control, USB Storage Service, Bandwidth Control, Interface

Grouping, IPTV, IP Tunnel and Connection Diagnostics, etc., create a

diverse network world for you.

1.2 Product Features

Wireless N: Speeds up to 300 Mbps for streaming HD videos and online gaming in addition to basic Internet

applications

All-in-one device combines a built-in ADSL2+ modem, wired router, wireless router and switch

Sharable USB lets you access and share files on an attached USB storage

Bandwidth Control helps prioritize media streaming and gaming applications for best entertainment experience

Parental Control keeps your kids Internet experience safe using flexible and customizable filter settings

One-touch WPS ensures a quick and secure network connection

WEP and WPA/WPA2 are supported for advanced encryptions

Compatibility: Works with all major ADSL Internet service providers (ISPs); backward compatible with 802.11b/g WiFi

devices

Interchangeable LAN/WAN ports to schedule the Ethernet port to function either as a LAN or a WAN port

1

Interchangeable LAN/IPTV to schedule the Ethernet port to function either as a LAN or an IPTV port

Optional Ethernet and ADSL Uplinks: Access the Internet via ADSL2+ Broadband Internet Service or an

interchangeable LAN/WAN RJ45 port

Multiple Internet Connection Types: PPPoE, PPPoA, IPoA, Bridge, dynamic IP and static IP

IPTV Service lets your surf the Internet while watching online TV

6000V lightning-proof design fits into lightning-intensive environment

Strong driving capability up to 6.5Km transmission distance

High speed ADSL speed up to 24Mbps downstream 1Mbps upstream

Built-in firewall prevents hacker attacks

Channel auto-select for optimum performance

FDM technology enables telephoning, faxing and surfing activities to proceed simultaneously without mutual

interference

Other Advanced Features: IPv6, DDNS, virtual server, DMZ, port triggering, IP filter, MAC filter and UPnP, etc.

Tenda Green: Equipped with hardware buttons Power On/Off and WiFi On/Off. You can conveniently turn on or off

power and WiFi to save energy when not in use

1.3 Package Contents

Your box should contain the following items:

 4 Antennas Wireless N300 ADSL2+ Modem Router

 Ethernet Cable

 Phone Cables (2)

 ADSL Splitter

 Install Guide

 Power Adapter

If any of the parts are incorrect, missing, or damaged, keep the carton, including the original packing materials and

contact your Tenda dealer for immediate replacement.

2

1.4 Front Panel

Item

Name

Status

Description

PWR

Solid

Power electricity is provided to the device properly.

Off

Power is off.

SYS

Solid/Off

The system is malfunctioning.

Blinking

The system works properly.

INTERNET

Solid

The device is connected to the Internet properly.

Blinking

Transmitting Internet data…

Off

The device is not connected to the Internet.

USB

Solid

A USB device is connected to the device.

Blinking

A USB device is connected and is working.

Off

No USB device is connected to the device.

WPS

Solid

A wireless device is connected to the device via WPS successfully. It will be off

in 5 minutes.

Blinking

It is waiting for a wireless device to join in.

Off

Wireless device has finished WPS negotiation or WPS is disabled.

WLAN

Solid

The wireless is enabled.

Blinking

The wireless is enabled and data is being transmitted via wireless.

Off

The wireless is disabled.

4/iTV, 3, 2,

1/WAN

Solid

The port is connected.

Blinking

The port is connected and data is being transmitted.

Off

The port is not connected.

DSL

Solid

DSL link is connected.

Blinking

DSL link is negotiating.

Off

DSL link is disconnected.

The LEDs on the device are described below:

3

1.5 Back Panel

Item

Name

Description

DSL

RJ11 port. Connect the telephone line from ISP to this port for DSL service connection.

1/WAN

LAN port or WAN port. When you access the Internet via the DSL, this port works as a LAN

port which can be used to connect to a PC, switch, or a router; when you access the Internet

via an Ethernet cable from your ISP directly, this port works as a WAN port.

Note: It works as a LAN port by default.

2/3

LAN port. Connect your devices like computer to this port.

4/iTV

LAN port or IPTV port. When IPTV feature is disabled, it works as a LAN port which can be

used to connect to a PC, switch or a router; when IPTV feature is enabled, it works as an IPTV

port, and it can only be connected to a Set-Top Box.

Note: IPTV feature is disabled by default.

USB

Used to connect a USB storage service for LAN sharing.

WLAN

Press this button for 3 seconds to enable/ disable WiFi.

WPS/RST

Press it for 1-3 seconds to do WPS negotiation. (Make sure WPS is enabled on Wireless >

Security screen ahead.)

Press it for 8 seconds to restore all configurations to factory defaults.

PWR

Connect the modem router to power supply via this port.

ON/OFF

Turn ON or OFF the modem router.

4

Chapter 2 Hardware Installation

Before you start to cable the modem router, you should figure out your Internet access type. Cable you modem router

correctly, and make sure it works well. It supports two types of access, DSL access and Ethernet access. Choose your

access type and cable your device and modem router.

This part includes the following:

2.1 DSL Access

2.2 Ethernet Access

2.1 DSL Access



DSL access cabling is detailed below. Cable the modem router and your computer following the steps ① →②→③.

① Insert the telephone line provided by your ISP into the DSL port of the modem router. (If you are using

telephone service and Internet service simultaneously, cable the ADSL spillter as the diagram below shows.)

② Connect the modem router to the power supply with the attached power adapter.

5

③ Connect your computer to the LAN port of the modem router.

The overall diagram of DSL Access is shown below:

_________________________________________________________________________________________________

TIP

1. Before connecting, make sure the Internet service is available.

2. ADSL splitter is used to make you active in phone service and Internet service simultaneously. If you don’t need

the telephone service, just connect the telephone line from your ISP to the DSL port.

3. Make sure that the DSL LED indicator is on and then configure the modem router.

4. Please use the included power adapter. Use of a power adapter with different voltage rating may damage the

device.

_________________________________________________________________________________________________

6

2.2 Ethernet Access

 Ethernet access cabling is detailed below. Cable the modem router and your computer following the steps

①→②→③.

Note that you may get to the Internet via a modem or an Ethernet cable directly, choose your access type correctly and

follow the diagram.

a1. If you get to the Internet via a modem (cable modem or fiber modem), follow this one.

b1. If you get to the Internet via Ethernet cable directly, follow this one.

Steps

and are same with that of DSL access. Click here to check.

7

The overall diagram of Ethernet Access is shown below:

_________________________________________________________________________________________________

TIP

1. Before connecting, make sure the Internet service is available.

2. Disconnect the modem router from WAN or DSL connection, and unplug it from the power when it is

thunderstorm.

_________________________________________________________________________________________________

8

Chapter 3 Internet Setup

Internet setups are detailed in this part, which include connection types, link types and wireless security setup, etc.

This part includes the following:

3.1 Log in to UI

3.2 Set up Internet

3.3 Quick Wireless Security Setup

3.1 Log in to UI (User Interface)

To configure the parameters of the modem router, you should log in to its UI (User Interface) first.

① Set your PC to Obtain an IP address automatically. For more information, see Appendix 2 Configure Your PC.

② Launch a web browser and enter 192.168.1.1 to display the login window.

③ Enter admin in both the login User Name and Password fields if you access the router for the

first time and then click Login to enter the home page.

_________________________________________

TIP

If you forgot your login user name and password,

press the WPS/RST button on the device for about

8 seconds to reset the router, and then re-log in with

the default user name and password “admin”.

_________________________________________

9

3.2 Set up Internet

The device supports auto-detecting link type and PVC, which can help you configure the device easily and quickly. If

you do want to configure the details, take below for references.

About Link Type

Link type includes three options: Auto, DSL and Ethernet.

Auto is recommended to you if you cannot figure out which type your Internet access is.

DSL is for a telephone line access, which means you access Internet service with a telephone line.

Ethernet is for an Ethernet cable access. If you are using this modem router with cable modem or fiber modem; or you

get an Ethernet cable access directly, select Ethernet.

About Connection Type

The device supports the following connection types, IPoE (Dynamic IP or Static IP), PPPoE, IPoA, PPPoA and Bridge.

You can set up Internet quickly on the Home page or click icon for more info about advanced settings.

10

Internet Setup Instruction

For

DSL access

 PPPoE

① Select Auto or DSL link type and select PPPoE connection type. (Note that Auto mode only supports two

connection types: PPPoE and IPoE.)

② Check Auto PVC scan. If the scan failed, uncheck this option and configure the PVC and country settings

manually. Click here to check PVC value or consult your ISP if you cannot locate this info.

③ Type the user name and password of PPPoE provided by your ISP.

④ Finish the wireless setup. (Recommended)

⑤ Click OK.

11

 PPPoA

① Select Auto or DSL link type and select PPPoA connection type. (Note that Auto mode only supports two

connection types: PPPoE and IPoE.)

② Configure the PVC, ISP and country settings manually. Click here to check PVC value or consult your ISP if

you cannot locate this info. (Note that Auto PVC scan is not available for PPPoA.)

③ Type the user name and password of PPPoA provided by your ISP.

④ Finish the wireless setup. (Recommended)

⑤ Click OK.

12

 IPoE

① Select Auto or DSL link type and select IPoE connection type.

② Check Auto PVC scan. If the scan failed, uncheck this option and configure the PVC and country settings

manually. Click here to check PVC value or consult your ISP if you cannot locate this info.

③ Select your address mode (Dynamic IP or Static IP). This is depending on your ISP.

 Dynamic IP mode requires nothing.

 Static IP requires a group of IP info provided by your ISP. Type them in the corresponding field.

④ Finish the wireless setup. (Recommended)

⑤ Click OK.

13

 IPoA

① Select Auto or DSL link type and select IPoA connection type.

② Configure the PVC, ISP and country settings manually. Click here to check PVC value or consult your ISP if

you cannot locate this info. (Note that Auto PVC scan is not available for IPoA.)

③ Select your address mode Static IP. And type the IP info provided by your ISP in the corresponding field.

④ Finish the wireless setup. (Recommended)

⑤ Click OK.

14

 Bridge

① Select Auto or DSL link type and select Bridge connection type.

② Configure the PVC, ISP and country settings manually. Click here to check PVC value or consult your ISP if

you cannot locate this info. (Note that Auto PVC scan is not available for Bridge.)

③ Finish the wireless setup. (Recommended)

④ Click OK.

When Bridge mode in DSL access is enabled, dial up from the local PC with the account provided by your ISP for

Internet service.

________________________________________________________________________________________________

NOTE

If your country and/or your ISP are not covered on the Home page, select “Other” from the country list and configure the

VPI and VCI value manually. If you cannot locate this information, refer to Appendix 5 VPI/VCI List or ask your ISP to

provide it. For more information, see To Set up the ATM interface and To Set up WAN Service for ATM Interface.

_________________________________________________________________________________________________

15

For Ethernet access

 PPPoE

① Select Auto or Ethernet link type and select PPPoE connection type.

② Type the user name and password of PPPoE provided by your ISP.

③ Finish the wireless setup. (Recommended)

④ Click OK.

 IPoE

① Select Auto or Ethernet link type and select IPoE connection type.

② Select your address mode (Dynamic IP or Static IP). This is depending on your ISP.

 Dynamic IP mode requires nothing.

16

 Static IP requires a group of IP info provided by your ISP. Type them in the corresponding field.

③ Finish the wireless setup. (Recommended)

④ Click OK.

 Bridge

① Link Type: Select Auto or Ethernet.

② Select Bridge connection type.

③ Finish the wireless setup. (Recommended)

④ Click OK.

When Bridge mode in Ethernet access is enabled, dial up from the local PC with the account provided by your ISP for

Internet service.

Test Internet Connectivity

After the device is correctly set, it may get to the Internet. (Connection Status: Connected)

You can launch a web browser and search

service.

www.tendacn.com. If the webpage displays, you are able to enjoy the Internet

17

3.3 Quick Wireless Security Setup

On Home Page, you can set up the basic wireless parameters, like wireless SSID, wireless key and RF Power (namely

signal strength). Also, you can disable or enable wireless feature here.

After you have finished settings, click

Wireless Enable: Check it to enable wireless feature.

RF Power: Namely signal strength. It includes Normal and Enhance options. Enhance means stronger signal.

Wireless SSID: It is the name of your WiFi. Set it as you like.

to save and apply them.

Wireless Key: It is the key of your WiFi. The WiFi is unencrypted by default, but there is a preset key in the wireless

key field. The preset key will work after you click

_________________________________________________________________________________________________

NOTE

1. If you change a new wireless key, the current WiFi connection will be stopped. You may try to connect the WiFi

with the new wireless key.

2. To join your wireless network, see Appendix 3 Join Your Wireless Network.

_________________________________________________________________________________________________

.

18

Chapter 4 Advanced Settings

This chapter describes the advanced features of your modem router. The information is for users with a solid

understanding of networking concepts who want to configure the router for unique situations.

This part includes the following:

4.1 Device Info

4.2 Advanced Setup

4.3 Wireless

4.4 Diagnostics

4.5 Management

4.1 Device Info

This section includes the following information:

• Summary • WAN • Statistics

• Route • ARP • DHCP

Summary

Here you can view system information and current status of your WAN connection as seen in the screenshot.

19

WAN

Here you can view the WAN Information including Interface, Description, Type, IGMP, NAT, Firewall, Status, IPv4

Address and VLAN ID as seen in the screenshot.

Statistics

Here you can view the packets received and transmitted on LAN/WAN ports.

Statistics--LAN: Displays the packets received and transmitted on the LAN ports as seen in the screenshot below.

_________________________________________________________________________________________________

TIP

2.4GHz interface represents data transmitted and received via wireless.

_________________________________________________________________________________________________

20

Statistics--WAN: Displays the packets received and transmitted on the WAN ports as seen in the screenshot below.

Statistics-ADSL: Displays the DSL port status e.g., packets received and transmitted on the DSL port.

Route

Here you can view the route table as seen in the screenshot:

21

ARP

Here you can view the IP and MAC addresses of the PCs that attach to the device either via a wired or wireless

connection as seen in the screenshot:

DHCP

Here you can view the DHCP leases, including IP and MAC addresses of the PCs, hostnames and remaining lease time

as seen in the screenshot. Note that if the DHCP server is disabled, this info will be hidden.

4.2 Advanced Setup

This section explains the following information:

• Layer2 Interface • DNS • Interface Grouping

• WAN Service • Bandwidth Control • Certificate

• LAN • Security • Multicast

• NAT • Parental Control • IP Tunnel

• Routing • IPTV

• DSL • Storage Service

22

4.2.1 Layer2 Interface

Click Advanced Setup > Layer2 Interface to enter the Layer2 Interface screen.

This router provides two kinds of Layer2 Interface:

- ATM Interface for ADSL broadband Internet service

- ETH Interface for connecting to the Internet via an Ethernet cable.

By default, system applies the ATM Interface (ADSL uplink).

If you directly connect to the ADSL line via a phone cable, first refer to

To Set up the ATM interface and then skip to

To Set up WAN Service for ATM Interface.

Or if you connect to the Internet via a fiber/cable modem using an Ethernet cable, first refer to To Set up the ETH

interface and then skip to To Set up WAN Service for ETH Interface.

To Set Up the ATM Interface

Select ATM Interface and click Add.

23

Enter the VPI and VCI values, select a DSL Link Type (Internet connection type): EoA (EoA is for PPPoE, IPoE, and

Bridge.), PPPoA or IPoA. Leave other options unchanged from factory defaults and click

and then refer to

To Set up WAN Service for ATM Interface to configure the WAN service for Internet access.

_________________________________________________________________________________________________

TIP

If you are unsure about the VPI/VCI parameters, see Appendix 5 VPI/VCI List. Or if your ISP and the VPI/VCI

information is not covered there, ask your ISP to provide it.

_________________________________________________________________________________________________

To Set Up the ETH Interface

Select ETH Interface and click Add.

24

Eth0 is 1/WAN port on the back of the device. It is to function as a WAN port here. After you finish your settings, click

and then refer to To Set up WAN Service for ETH Interface to configure the WAN service for Internet

access.

4.2.2 WAN Service

This router provides two WAN services:

- WAN Service for ATM Interface (ADSL uplink)

- WAN Service for ETH Interface (Ethernet uplink)

To Set up WAN Service for ATM Interface

 EoA (PPPoE, IPoE and Bridge)

If you configured the ATM Interface (ADSL uplink) and select EoA as the DSL link type, follow below steps to

configure the WAN service:

25

PPPoE

IPv4 Only

Step 1: Click Advanced Setup > WAN Service and then click the Add button.

Step 2: Select the ATM interface you added just now from the pull-down menu in the figure below. Click Next.

Step 3: Select PPP over Ethernet (PPPoE). Edit the Enter Service Description field which is optional. Suggest you

keep the default. Select a network protocol: IPv4 Only. Click Next.

26

Step 4: Finish PPP Username and Password and other settings on the figure below. Click Next.

PPP Username/Password: For logging in to your ISP. If you cannot locate this information, ask your ISP to provide it.

PPPoE Service Name: Provided by your ISP. Only enter it if instructed by your ISP.

Authentication Method: Used by ISP to authenticate the client that attempts to connect. If you are not sure, consult

your ISP or select AUTO.

MAC Clone: When you cannot access the Internet after finishing other settings here except this option, consider

whether it’s the matter of the MAC address of your computer. Clicking Clone MAC button copies the MAC address of

your computer to the router.

MTU: Keep the default value unless you are sure it is necessary for your ISP connection.

Dial on demand: Connect to ISP only when there is traffic transmission. This saves your broadband Internet service bill.

PPP IP extension: If enabled, all the IP addresses in outgoing packets including management packets on the WAN port

will be changed to the device's WAN IP address. Only change the default settings if necessary.

Enable PPP Debug Mode: Only enable this feature if supported by your ISP.

Bridge PPPoE Frames Between WAN and Local Ports: If enabled, PPPoE dialup frame from LAN side will directly

egress the WAN port without modification.

Multicast Proxy: If enabled, the router will use multicast proxy.

KNOWLEDGE EXPANSION

1. MAC Clone: Many broadband ISPs restrict access by allowing traffic only from the MAC address of your broadband

modem, but some ISPs additionally register the MAC address of your computer when your account is first opened. If so,

only by cloning the MAC address of your computer can you access the Internet through the router.

2. MTU: Short for Maximum Transmission Unit, the largest physical packet size, measured in bytes, which

27

a network can transmit. Any messages larger than the MTU are divided into smaller packets before being sent. The

default MTU is 1460 bytes. For some ISPs, you might need to change the MTU. This is rarely required, and should not

be done unless you are sure it is necessary for your ISP connection.

Step 5: To configure the Default Gateway interface, select the interface that you want to configure with the WAN

gateway address in Available Routed WAN Interfaces box and move it into Selected Default Gateway Interfaces box.

The default setting is recommended. Then click Next.

Step 6: To configure the WAN DNS address, click the Select DNS Server Interface from available WAN interfaces

option, or select the Use the following Static DNS IP address option and enter the static DNS server IP addresses

provided by your ISP. At last, click Next.

28

Step 7: Here you can view your configurations. Click Apply/Save to save your settings if everything is correctly set.

When the PPPoE connection is successful, you can access the Internet.

IPv4 & IPv6 (Dual Stack)

Step 1: Click Advanced Setup > WAN Service and then click the Add button.

Step 2: Select the ATM interface you added just now from the pull-down menu in the figure below. Click Next.

29

Step 3: Select PPP over Ethernet (PPPoE). Edit the Enter Service Description field which is optional. Suggest you

keep the default. Select a network protocol: IPv4&IPv6 (Dual Stack). Click Next.

Step 4: Configure PPP Username and Password and other settings on the figure below. Each field with its indication is

mentioned above in IPv4 Only (PPPoE) section. Check Launch Dhcp6c for Prefix Delegation (IAPD). Click Next.

If your ISP is using static DHCPv6, check Launch Dhcp6c for Address Assignment (IANA) also, or configure a static

30

IP address by checking Use Static IPv6 Address and enter the static IPv6 address.

Step 5: To configure the Default Gateway interface when using IPv6, select the interface that you want to configure with

the WAN gateway address in Selected WAN Interface box. Then click Next.

Step 6: To configure the WAN DNS address, check the Obtain IPv6 DNS info from a WAN interface option, or select

the Use the following Static IPv6 DNS address option to enter the static DNS server IPv6 addresses provided by your

ISP. At last, click Next.



Step 7: Here you can view your configurations. Click Apply/Save to save your settings if everything is correctly set.

31



When the PPPoE connection is successful, you can access the Internet.

IPv6 Only

Step 1: Click Advanced Setup > WAN Service and then click the Add button.

Step 2: Select the ATM interface you added just now from the pull-down menu in the figure below. Click Next.

32

Step 3: Select PPP over Ethernet (PPPoE). Edit the Enter Service Description field which is optional. Suggest you

keep the default. Select a network protocol you need: IPv6 Only. Click Next.

Step 4: Configure PPP Username and Password and other settings on the figure below. Each field with its indication is

mentioned above in IPv4 Only (PPPoE) section.

If ISP provides you no static IPv6 address, you just keep the default settings for it’s by default the DHCP mode. Check

Launch Dhcp6c for Prefix Delegation (IAPD). If your ISP is using stateful DHCPv6, check Launch Dhcp6c for

Address Assignment (IANA) also. Click Next.

33

If ISP provides you with the static IPv6 address, configure a static IP address by checking Use Static IPv6 Address and

enter the static IPv6 address.

Step 5: To configure the Default Gateway interface when using IPv6, select the interface that you want to configure with

the WAN gateway address in Selected WAN Interface box. Then click Next.

Step 6: To configure the WAN DNS address, check the Obtain IPv6 DNS info from a WAN interface option, or select

the Use the following Static IPv6 DNS address option to enter the static DNS server IPv6 addresses provided by your

ISP. At last, click Next.



Step 7: Here you can view your configurations. Click Apply/Save to take this interface into effect.

34



When the PPPoE connection is successful, you can access the Internet.

IPoE

IPv4 Only

If you get an IP address from your ISP automatically or if your ISP assigns you a static (fixed) IP address, subnet mask

and gateway, you need to select the IP over Ethernet (IPoE).

Step 1: Click Advanced Setup > WAN Service and then click the Add button.

Step 2: Select the ATM interface you added just now from the pull-down menu in the figure below. Click Next.

35

Step 3: Select IP over Ethernet. Edit the Enter Service Description which is optional. Suggest you keep the default.

Select a network protocol: IPv4 Only. Click Next.

Step 4: Finish WAN IP Settings on the figure below. Click Next.

36

Obtain an IP address automatically: This allows the router to automatically acquire IP information from your ISP or

your existing networking equipment.

Use the following Static IP address: This allows you to specify the Static IP information provided by your ISP or that

corresponds with your existing networking equipment.

WAN IP Address: The Internet IP address provided by your ISP for accessing the Internet.

WAN Subnet Mask: The subnet mask address provided by your ISP for accessing the Internet.

WAN gateway IP Address: The gateway IP address provided by your ISP for accessing the Internet.

Step 5: Finish Network Address Translation Settings. Suggest keep the default settings. Click Next.

Step 6: To configure the Default Gateway interface, select the interface that you want to configure with the WAN

gateway address in Available Routed WAN Interfaces box and move it into Selected Default Gateway Interfaces box.

The default setting is recommended. Then click Next.

37

Step 7: To finish DNS Server Configuration, click the Select DNS Server Interface from available WAN interfaces

option, or select the Use the following Static DNS IP address option and enter the static DNS server IP addresses

provided by your ISP. At last, click Next.



Step 8: Here you can view your configurations. Click Apply/Save to save your settings if everything is correctly set.



When the IPoE connection is successful, you can access the Internet.

38

IPv4 & IPv6 (Dual Stack)

Step 1: Click Advanced Setup > WAN Service and then click the Add button.

Step 2: Select the ATM interface you added just now from the pull-down menu in the figure below. Click Next.

Step 3: Select IP over Ethernet. Edit the Enter Service Description which is optional. Suggest you keep the default.

Select a network protocol: IPv4&IPv6 (Dual Stack). Click Next.

39

Step 4: To finish WAN IP Settings, select Obtain an IPv6 address automatically, check Dhcpv6 Prefix Delegation

(IAPD). If your ISP is using stateful DHCPv6, check Dhcpv6 Address Assignment (IANA) also. Or select Use the

following Static IP address if your ISP provides you with an IPv6 address. Click Next.

If ISP provides you with the static IPv6 address, configure a static IP address by checking Use the following Static IPv6

address and enter the static IPv6 address.

40

Step 5: Configure NAT settings. If you are unsure about the options, please keep the default settings and then click Next.

Step 6: To configure the Default Gateway interface, select the interface that you want to configure with the WAN

gateway address in Available Routed WAN Interfaces box and move it into Selected Default Gateway Interfaces box.

Then click Next.

Step 7: To configure the WAN DNS address, check the Obtain IPv6 DNS info from a WAN interface option, or select

the Use the following Static IPv6 DNS address option to enter the static DNS server IPv6 addresses provided by your

ISP. At last, click Next.

41

Step 8: Here you can view your configurations. Click Apply/Save to save your settings if everything is correctly set.

When the IPoE connection is successful, you can access the Internet.

IPv6 Only

Step 1: Click Advanced Setup > WAN Service and then click the Add button.

Step 2: Select the ATM interface you added just now from the pull-down menu in the figure below. Click Next.

42

Step 3: Select IP over Ethernet (IPoE). Edit the Enter Service Description field which is optional. Suggest you keep

the default. Select a network protocol you need: IPv6 Only. Click Next.

Step 4: Enter the WAN information provided by your ISP to configure the WAN IPv6 settings.

To obtain an IP address automatically:

Select Obtain an IPv6 address automatically.

Check Dhcp6c Prefix Delegation (IAPD).

If your ISP is using stateful DHCPv6, check Dhcp6c Address Assignment (IANA) also.

Click Next to go forwards.

43

Step 5: Finish Network Address Translation Settings. Suggest keep the default settings. Click Next.

Step 6: To configure the Default Gateway interface when using IPv6, select the interface that you want to configure with

the WAN gateway address in Selected WAN Interface box. Then click Next.

Step 7: To configure the WAN DNS address, check the Obtain IPv6 DNS info from a WAN interface option, or select

the Use the following Static IPv6 DNS address option to enter the static DNS server IPv6 addresses provided by your

ISP. At last, click Next.

44

Step 8: Here you can view your configurations. Click Apply/Save to have this interface to be effective.

When the IPoE connection is successful, you can access the Internet.

Bridge

If you wish to initiate a dialup directly from your PC for Internet access or enjoy the entire Internet connection (instead

of sharing it with others), you can use the Bridging DSL link type and create a dialup program on your PC.

Step 1: Click Advanced Setup > WAN Service and then click the Add button.

Step 2: Select the ATM interface you added just now from the pull-down menu in the figure below. Click Next.

45

Step 3: Select Bridging. Edit the Enter Service Description which is optional. Suggest you keep the default. Click

Next.

Step 4: Here you can view your configurations. Click Apply/Save to activate your settings..

46

After the bridging connection is successful, initiate a dialup directly from your PC for Internet access.

NOTE

To configure multiple WAN connections, simply configure multiple ATM interfaces and then follow the instructions

above.

 PPPoA

If you have selected the PPPoA from the ATM Interface screen in Layer2 Interface, you will see the screen below

when you click the WAN Service tab, select the configured interface and click Next.

IPv4 Only

Step 1: Click Advanced Setup > WAN Service and then click the Add button.

Step 2: Select the ATM interface you added just now from the pull-down menu in the figure below. Click Next.

Step 3: Edit the Enter Service Description. This field is optional. We recommend that you keep the default.

Select a network protocol: IPv4 Only and click Next.

47

Step 4: Enter PPP username and its password provided by your ISP. Click Next.

PPP Username: This is for logging in to your ISP. If you cannot locate this information, ask your ISP to provide it.

PPP Password: This is for logging in to your ISP. If you cannot locate this information, ask your ISP to provide it.

Authentication Method: This is used by ISP to authenticate the client that attempts to connect. If you are not sure,

consult your ISP or select AUTO.

Dial on demand: Connect to ISP only when there is traffic transmission. This saves your broadband Internet service bill.

Enable PPP Debug Mode: Only enable this feature if supported by your ISP.

Multicast Proxy: If enabled, the router will use multicast proxy.

If you are not sure about the options on this screen, simply enter your ISP user name and password and leave the other

options unchanged from defaults. Click Next to enter the following screen.

48

Step 5: To configure the WAN gateway address. After you configure it click Next. The default setting is recommended.

Step 6: To configure the WAN DNS address. Choose a way to get DNS server according to what your ISP has provided.

-Click the Select DNS Server Interface from available WAN interfaces option.

-Select the Use the following Static DNS IP address option and enter static DNS server IP addresses for the system.

And then click Next.

NOTE

1. In ATM mode, if only a single PVC with IPoA or static IPoE protocol is configured, Static DNS server IP addresses

must be entered.

2. If you cannot locate the static DNS server IP information, ask your ISP to provide it.

49

Step 7: Here you can view your configurations. Click Apply/Save to have this interface to be effective.

Step 8: When the PPPoA connection is successful, you can access the Internet.

IPv4 & IPv6 (Dual Stack)

Step 1: Click Advanced Setup > WAN Service and then click the Add button.

Step 2: Select the ATM interface you added just now from the pull-down menu in the figure below. Click Next.

50

Step 3: Edit the Enter Service Description. This field is optional. We recommend that you keep the default.

Select a network protocol: IPv4 & IPv6 (Dual Stack). Click Next.

Step 4: Enter PPP username and its password provided by your ISP. Click Next.

Step 5: To configure the WAN gateway address. After you configure it click Next. The default setting is recommended.

51

NOTE

Default gateway interface list can have multiple WAN interfaces served as system default gateways but only one will be

used according to the priority with the first being the highest and the last one the lowest priority if the WAN interface is

connected. Priority order can be changed by removing all and adding them back in again.

Step 6: To configure the WAN DNS address

Select DNS Server Interface from available WAN interfaces OR enter static DNS server IP addresses for the system. And

then click Next.

NOTE

1. DNS Server Interfaces can have multiple WAN interfaces served as system DNS servers but only one will be used

according to the priority with the first being the highest and the last one the lowest priority if the WAN interface is

connected. Priority order can be changed by removing all and adding them back in again.

2. In ATM mode, if only a single PVC with IPoA or static IPoE protocol is configured, Static DNS server IP addresses

must be entered.

3. If you cannot locate the static DNS server IP information, ask your ISP to provide it.

52

Step 7: Here you can view your configurations. Click Apply/Save to save your settings if everything is correctly set.

Step 8: When the PPPoA connection is successful, you can access the Internet.

IPv6 Only

Step 1: Click Advanced Setup > WAN Service and then click the Add button.

Step 2: Select the ATM interface you added just now from the pull-down menu in the figure below. Click Next.

53

Step 3: Edit the Enter Service Description. This field is optional. We recommend that you keep the default.

Select a network protocol: IPv6 Only. Click Next.

Step 4: Enter PPP username and its password provided by your ISP. Click Next.

Step 5: Select a preferred wan interface as the system default IPv6 gateway. Click Next.

54

Step 6: To configure the WAN DNS address, select the configured WAN interface for IPv6 DNS server information or

enter the static IPv6 DNS server addresses. And then click Next.

NOTE

Selecting a WAN interface for IPv6 DNS server will enable DHCPv6 Client on that interface.

Step 7: Here you can view your configurations. Click Apply/Save to save your settings if everything is correctly set.

Step 8: When the PPPoA connection is successful, you can access the Internet.

55

 IPoA

Step 1: Click Advanced Setup > WAN Service and then click the Add button.

Step 2: Select the ATM interface you added just now from the pull-down menu in the figure below. Click Next.

Step 3: Edit the Enter Service Description. This field is optional. It is recommended that you keep the default. Click

Next.

Step 4: Enter the WAN IP address and subnet mask which should have been provided to you by your ISP. If you cannot

locate this information, ask your ISP to provide it. And then click Next.

56

WAN IP Address: The Internet IP address provided by your ISP for accessing the Internet.

WAN Subnet Mask: The subnet mask address provided by your ISP for accessing the Internet.

Step 5: Keep the defaults if you are unsure about the options on the screen below and click Next.

Step 6: To configure the WAN gateway address. After you configure it click Next. The default setting is recommended.

NOTE

Default gateway interface list can have multiple WAN interfaces served as system default gateways but only one will be

used according to the priority with the first being the highest and the last one the lowest priority if the WAN interface is

connected. Priority order can be changed by removing all and adding them back in again.

Step 7: Configure the WAN DNS Server configuration according to your ISP.

-Click the Select DNS Server Interface from available WAN interfaces option;

-Or select the Use the following Static DNS IP address option and enter static DNS server IP addresses for the system.

And then click Next.

57

Step 8: Here you can view your configurations. Click Apply/Save to save your settings if everything is correctly set.

Step 9: IPoA WAN service setup parameter is shown as below.

58

To Set up WAN Service for ETH Interface

Three Internet connections: PPP over Ethernet (PPPoE), IP over Ethernet (IPoE) and Bridging are available in the

Ethernet uplink mode.

If you selected and configured the ETH Interface (Ethernet uplink), follow steps below to configure the WAN service:

 PPP over Ethernet (PPPoE)

IPv4

Step 1: Click Advanced Setup > WAN Service and then click the Add button.

Step 2: Select the ETH interface you added just now from the pull-down menu in the figure below. Click Next.

Step 3: Select PPP over Ethernet. Edit the Enter Service Description. This field is optional. It is recommended that

you keep the default. Select a network protocol: IPv4 Only. And click Next.

59

Step 4: Enter the PPP username and password provided by your ISP. If you are not sure about other options, just leave

them unchanged from defaults. And click Next.

PPP Username: This is for logging in to your ISP. If you cannot locate this information, ask your ISP to provide it.

PPP Password: This is for logging in to your ISP. If you cannot locate this information, ask your ISP to provide it.

PPPoE Service Name: This information is provided by your ISP. Only enter it if instructed by your ISP.

Authentication Method: This is used by ISP to authenticate the client that attempts to connect. If you are not sure,

consult your ISP or select Auto.

MAC Clone: Clicking Clone MAC button copies the MAC address of your PC to the router. Many broadband ISPs

restrict access by allowing traffic only from the MAC address of your broadband modem, but some ISPs additionally

register the MAC address of the network interface card in your computer when your account is first opened. They then

accept traffic only from the MAC address of that computer. If so, configure your router to “clone” the MAC address

from the authorized computer.

MTU: Short for Maximum Transmission Unit, the largest physical packet size, measured in bytes, which a network can

transmit. Any messages larger than the MTU are divided into smaller packets before being sent. The default MTU is

1460 bytes. For some ISPs, you might need to change the MTU. This is rarely required, and should not be done unless

you are sure it is necessary for your ISP connection.

Dial on demand: Connect to ISP only when there is traffic transmission. This saves your broadband Internet service bill.

PPP IP extension: If enabled, all the IP addresses in outgoing packets including management packets on the WAN port

will be changed to the device's WAN IP address. Only change the default settings if necessary.

Enable PPP Debug Mode: Only enable this feature if supported by your ISP.

Bridge PPPoE Frames Between WAN and Local Ports: If enabled, PPPoE dialup frame from LAN side will directly

60

egress the WAN port without modification.

Multicast Proxy: If enabled, the router will use multicast proxy.

Step 5: Configure the WAN gateway address. After you configure it click Next. The default setting is recommended.

Step 6: Configure the WAN DNS address according to your ISP.

-Click the Select DNS Server Interface from available WAN interfaces option;

-Or select the Use the following Static DNS IP address option and enter static DNS server IP addresses for the system.

And then click Next.

Step 7: Here you can view your configurations. Click Apply/Save to save your settings if everything is correctly set.

61

When the PPPoE connection is successful, you can access the Internet.

IPv4 & IPv6 (Dual Stack)

Step 1: Click Advanced Setup > WAN Service and then click the Add button.

Step 2: Select the ETH interface you added just now from the pull-down menu in the figure below. Click Next.

62

Step 3: Select PPP over Ethernet. Edit the Enter Service Description. This field is optional. It is recommended that

you keep the default. Select a network protocol: IPv4&IPv6 (Dual Stack). And click Next.

Step 4: Enter PPP username and PPP password provided by your ISP. Check Launch Dhcp6c for Prefix Delegation

(IAPD). If your ISP is using stateful DHCPv6, check Launch Dhcp6c for Address Assignment (IANA) also. Or

configure a static IP address.

63

Step 5: Select an available WAN interface as the system default gateway. Then click Next.

Step 6: Configure DNS server (Select an available DNS server interface or use a specified DNS server); configure IPv6

DNS server (Obtain IPv6 DNS info from a WAN interface or use a specified DNS server), and then click Next.

Step 7: Here you can view your configurations. Click Apply/Save to save your settings if everything is correctly set.

64

When the PPPoE connection is successful, you can access the Internet.

IPv6

Step 1: Click Advanced Setup > WAN Service and then click the Add button.

Step 2: Select the ETH interface you added just now from the pull-down menu in the figure below. Click Next.

Step 3: Select PPP over Ethernet. Edit the Enter Service Description. This field is optional. It is recommended that

you keep the default. Select a network protocol: IPv6 Only. And click Next.

65

Step 4: Enter PPP username and PPP password provided by your ISP. Check Launch Dhcp6c for Prefix Delegation

(IAPD). If your ISP is using stateful DHCPv6, check Launch Dhcp6c for Address Assignment (IANA) also. Or

configure a static IP address.

Step 5: Select a preferred WAN interface from the WAN interface list as the system default IPv6 gateway. Click Next.

Step 6: Select the configured WAN interface for IPv6 DNS server information or use a static IPv6 DNS server address.

Note that selecting a WAN interface for IPv6 DNS server will enable DHCPv6 Client on that interface. And then click

Next.

66

Step 7: Here you can view your configurations. Click Apply/Save to save your settings if everything is correctly set.

When the PPPoE connection is successful, you can access the Internet.

67

 IP over Ethernet (IPoE)

If you get an IP address from your ISP automatically or if your ISP assigns you a static (fixed) IP address, subnet mask

and gateway, you need to select the IP over Ethernet (IPoE).

IPv4

Step 1: Click Advanced Setup > WAN Service and then click the Add button.

Step 2: Select the ETH interface you added just now from the pull-down menu in the figure below. Click Next.

Step 3: Select IP over Ethernet as WAN service type. Edit the Enter Service Description. This field is optional. It is

recommended that you keep the default. Select a network protocol: IPv4 Only. And then click Next.

68

Step 4: Enter the IP address/subnet mask/gateway IP address provided by your ISP or select Obtain an IP address

automatically and then click the Next button.

Obtain an IP address automatically: This allows the router to automatically acquire IP information from your ISP or

your existing networking equipment.

Use the following Static IP address: This allows you to specify the Static IP information provided by your ISP or that

corresponds with your existing networking equipment.

WAN IP Address: The Internet IP address provided by your ISP for accessing the Internet.

WAN Subnet Mask: The subnet mask address provided by your ISP for accessing the Internet.

WAN gateway IP Address: The gateway IP address provided by your ISP for accessing the Internet.

Step 5: Here you can configure the NAT. If you are not an advanced user, the default settings are recommended and then

click Next.

69

Step 6: Here you can configure the WAN gateway address. After you configure it click Next. The default setting is

recommended.

Step 7: Here you can configure the WAN DNS address.

-Click the Select DNS Server Interface from available WAN interfaces option;

-Or select the Use the following Static DNS IP address option and enter static DNS server IP addresses for the system.

And then click Next.

Step 8: Here you can view your configurations. Click Apply/Save to save your settings if everything is correctly set.

70

When the IPoE connection is successful, you can access the Internet.

IPv4 & IPv6 (Dual Stack)

Step 1: Click Advanced Setup > WAN Service and then click the Add button.

Step 2: Select the ETH interface you added just now from the pull-down menu in the figure below. Click Next.

Step 3: Select IP over Ethernet as WAN service type. Edit the Enter Service Description. This field is optional. It is

recommended that you keep the default. Select a network protocol: IPv4&IPv6 (Dual Stack). And then click Next.

71

Step 4: Enter information provided by your ISP to configure the WAN IP settings.

72

Step 5: Here you can configure the NAT. If you are not an advanced user, the default settings are recommended and then

click Next.

Step 6: Configure a WAN interface as the default gateway.

Step 7: Configure DNS server (Select an available DNS server interface or use a specified DNS server); configure IPv6

DNS server (Obtain IPv6 DNS info from a WAN interface or use a specified DNS server), and then click Next.

73

Step 8: Here you can view your configurations. Click Apply/Save to save your settings if everything is correctly set.

When the IPoE connection is successful, you can access the Internet.

IPv6

Step 1: Click Advanced Setup > WAN Service and then click the Add button.

Step 2: Select the ETH interface you added just now from the pull-down menu in the figure below. Click Next.

74

Step 3: Select IP over Ethernet as WAN service type. Edit the Enter Service Description. This field is optional. We

recommend that you keep the default. Select a network protocol: IPv6 Only. And then click Next.

Step 4: Enter the WAN information provided by your ISP to configure the WAN IPv6 settings.

To obtain an IP address automatically:

Select Obtain an IPv6 address automatically and Check Dhcp6c Prefix Delegation (IAPD).

If your ISP is using stateful DHCPv6, check Dhcp6c Address Assignment (IANA) also. Click Next to go forwards.

75

Step 5: Here you can configure the NAT. If you are not an advanced user, the default settings are recommended and then

click Next.

Step 6: To configure the Default Gateway interface when using IPv6, select the interface that you want to configure with

the WAN gateway address in Selected WAN Interface box. Then click Next.

Step 7: To configure the WAN DNS address, check the Obtain IPv6 DNS info from a WAN interface option, or select

the Use the following Static IPv6 DNS address option to enter the static DNS server IPv6 addresses provided by your

ISP. At last, click Next.

76

Step 8: Here you can view your configurations. Click Apply/Save to save your settings if everything is correctly set.

When the IPoE connection is successful, you can access the Internet.

 Bridging

If you wish to initiate a dialup directly from your PC for Internet access or enjoy the entire Internet connection (instead

of sharing it with others), you can select the Bridging and create a dialup program from your PC.

Step 1: Click Advanced Setup > WAN Service and then click the Add button.

Step 2: Select the ETH interface you added just now from the pull-down menu in the figure below. Click Next.

Step 3: Select Bridging. Edit the Enter Service Description. This field is optional. It is recommended that you keep the

77

default. And click Next.

Step 4: Here you can view your configurations. Click Apply/Save to save your settings if everything is correctly set.

After the bridging connection is successful, initiate a dialup directly from your PC for Internet access.

78

4.2.3 LAN Setup

Here you can configure the LAN IP Address and subnet mask. This IP address is to be used to access the device’s

settings through a web browser. Be sure to make a note of any changes you apply to this page.

This part includes the following information:

 IPv4

 IPv6 Autoconfig

IPv4

IP Address: The device's LAN IP address. The default setting is 192.168.1.1.

Subnet Mask: The LAN subnet mask of the device. Combined with the IP address, the IP Subnet Mask allows a device

to know which other addresses are local to it, and which must be reached through a gateway or modem router. You can

change the subnet mask to fit your network.

Enable IGMP Snooping: Check to enable the IGMP Snooping. It is recommended to keep the default settings.

Disable DHCP Server: Click to disable the DHCP Server.

Enable DHCP Server: Click to enable the DHCP Server.

Start IP Address: Specify the start of the range for the pool of IP addresses in the same subnet as the router.

End IP Address: Specify the end of the range for the pool of IP addresses in the same subnet as the router.

79

Leased Time: The lease time is a time length that the IP address is assigned to each device before it is refreshed.

Static IP Lease List: Displays a list of devices with reserved static IP addresses.

Add Entries: Click to add a static IP lease entry. A maximum 32 entries can be configured.

Remove Entries: Click to remove a static IP lease entry.

Configure the second IP Address and Subnet Mask for LAN interface: If you want to configure two IP addresses for

the LAN interface, you can check this option and enter the second IP Address and Subnet Mask manually.

Apply/Save: After you configure all the needed settings, click this button to apply and save them.

_________________________________________________________________________________________________

TIP

DHCP (Dynamic Host Configuration Protocol) assigns an IP address to each device on the LAN/private network. When

you enable the DHCP Server, the DHCP Server will automatically allocate an unused IP address from the IP address pool

specified in this screen to the requesting device as long as the device is set to "Obtain an IP Address Automatically". By

default, DHCP is enabled.

IPv6 Autoconfig

 Static LAN IPv6 Address Configuration

Interface Address (prefix length is required): Enter the interface address.

_________________________________________________________________________________________________

NOTE

1. IPv6 address can only be Aggregatable Global Unicast Addresses and Unique Local Address. Link-Local Unicast

Addresses and Multicast Addresses are not permitted.

2. The IPv6 address must be entered with a prefix length.

_________________________________________________________________________________________________

80

 IPv6 LAN Applications

Enable DHCPv6 Server：Check to enable the DHCPv6 Server.

Stateless: If selected, IPv6 clients will generate IPv6 addresses automatically based on the Prefix Delegation's IPv6

prefix and their own MAC addresses.

Stateful: Stateful DHCPv6 is supported based on the assumption of prefix length less than 64. Select this option and

configure the start/end interface ID and leased time. The router will automatically assign IPv6 addresses to IPv6 clients.

Leased Time (hour): The lease time is a time length that the IP address is assigned to each device before it is refreshed.

Start interface ID/End interface ID: Specify the start/end interface ID Interface ID does NOT support ZERO

COMPRESSION "::". Please enter the complete information. For example: Please enter "0:0:0:2" instead of "::2".

Enable RADVD: The RADVD (Router Advertisement Daemon) implements link-local advertisements of IPv6 router

addresses and IPv6 routing prefixes using the Neighbor Discovery Protocol (NDP) and is used by system administrators

in stateless autoconfiguration methods of network hosts on Internet Protocol version 6 networks. Check the checkbox to

enable the RADVD.

Enable ULA Prefix Advertisement: If enabled, the router will advertise ULA prefix periodically

Randomly Generate: If selected, address prefix can be automatically generated.

Statically Configure: If you select this option, you need to manually configure the address prefix and life time.

Prefix: Specify the prefix.

Preferred Life Time (hour): Specify the preferred life time in hour.

Valid Life Time (hour): Specify the valid life time in hour.

Enable MLD Snooping: MLD is used by IPv6 routers for discovering multicast listeners on a directly attached link. If

disabled on layer2 devices, IPv6 multicast data packets will be broadcast on the entire layer2; if enabled, these packets

will be multicast to only specified recipient instead of being broadcast on the entire layer2.

_________________________________________________________________________________________________

TIP

If you change the LAN IP address of the device, the current connection to the device will be stopped. You must use the

new IP address to log in to the device. Be sure to write the new address on a sticky label and attach it to the bottom of the

unit. You will need the new address to log in to the device in the future.

_________________________________________________________________________________________________

81

4.2.4 NAT

This section explains the following:

• Virtual Server

• Port Triggering

• DMZ Host

• UPnP

Virtual Server

The Virtual Server is useful for web servers, ftp servers, e-mail servers, gaming and other specialized Internet

applications. When you enable the Virtual Server, the communication requests from the Internet to your router’s WAN

port will be forwarded to the specified LAN IP address.

To enter the virtual server screen, click NAT > Virtual Server and then click the Add button to add rules.

Use Interface: Select a WAN connection to which you wish to apply the rules. When there is only one WAN connection

available, the rules will be automatically applied to it.

Service Name:

- Select a Service: Allows you to select an existing service from the drop-down list.

- Custom Service: Allows you to customize a service.

Server IP Address: Enter the IP address of your local computer that will provide this service.

External Starting Port and External Ending Port: These are the starting number and ending number for the public

82

ports at the Internet interface.

Protocol: Select the protocol from the Protocol drop-down list. If you are unsure, select TCP/UDP.

Internal Starting Port and Internal Ending Port: These are the starting number and ending number for the ports of a

computer on the router’s local area network (LAN).

_________________________________________________________________________________________________

NOTE

If you have enabled the UPnP functionality on both the router and your PC that is attached to one of the LAN port of the

router, you will be prompted on the Virtual Server page that the UPnP interface is being used.

_________________________________________________________________________________________________

Instance

You have set up two servers on your LAN side:

- An FTP server (using the default port number of 21) at the IP address of 192.168.1.100

- A web server (using the default port number of 8080) at the IP address of 192.168.1.110

And want your friends on the Internet to access the FTP server and web server via default ports. To access your FTP or

web server from the Internet, a remote user has to know the WAN IP address of your router. In this example, we assume

the WAN IP address of your router is 183.37.227.201. Then follow instructions below:

To configure the router to make your local FTP server public:

Procedure

1. Click NAT > Virtual Server to enter it and then click the Add button.

2. Select FTP Server that you wish to host on your network from the Select a Service drop-down list. The port

number (21) used by this service will then be automatically populated.

- Or if you wish to define the service yourself, enter a descriptive name in the Custom Service, say My FTP, and

then manually enter the port number (21) used by this service in the Internal Starting Port, Internal Ending Port,

External Starting Port and External Ending Port fields.

3. Select a protocol from the Protocol drop-down list. If you are unsure, select TCP/UDP.

4. In the Server IP Address field, enter the last digit of the IP address of your local computer that offers this service.

Here in this example, we enter 100.

5. Click .

Your friends on the Internet will then be able to access your FTP server simply by "ftp://183.37.227.201:21".

83

To configure your router to make your local web server public:

Procedure

1. Click NAT > Virtual Server to enter it and then click the Add button.

2. Select Web Server (HTTP) that you wish to host on your network from the Select a Service drop-down list. The

port number (8080) used by this service will then be automatically populated.

- Or if you wish to define the service yourself, enter a descriptive name in the Custom Service, say My Web Server

(HTTP), and then manually enter the port number (8080) used by this service in the Internal Starting Port,

Internal Ending Port, External Starting Port and External Ending Port fields.

3. Select a protocol from the Protocol drop-down list. If you are unsure, select TCP/UDP.

4. In the Server IP Address field, enter the last digit of the IP address of your local computer that offers this service.

Here in this example, we enter 110.

5. Click

.

Now you can view your configurations as seen in the screenshot below. Your friends on the Internet will then be able to

access the web server simply by entering "http://183.37.227.201:8080" in his browser.

_________________________________________________________________________________________________

NOTE

1. The "Internal Port End" cannot be modified directly. Normally, it is set to the same value as "External Port End".

However, if you modify "Internal Port Start", then "Internal Port End" will be set to the same value as "Internal Port

Start".

2. If the service or game you wish to host on your network is not included in the list, manually add it in the Custom

Service field and then add the port number used by it to the Internal Starting Port, Internal Ending Port, External

Starting Port and External Ending Port fields.

_________________________________________________________________________________________________

84

Port Triggering

Some applications such as games, video conferencing, remote access applications and others require that specific ports in

the Router's firewall be opened for access by the applications. Port Trigger dynamically opens up the 'Open Ports' in the

firewall when an application on the LAN initiates a TCP/UDP connection to a remote party using the 'Triggering Ports'.

The Router allows the remote party from the WAN side to establish new connections back to the application on the LAN

side using the 'Open Ports'.

To enter the Port Triggering screen, click NAT > Port Triggering and then click the Add button to add rules.

You can configure the port settings from this screen by selecting an existing application or creating your own (Custom

application) and click Save/Apply to add it.

Use Interface: Select a WAN connection to which you wish to apply the rules. When there is only one WAN connection

available, the rules will be automatically applied to it.

Application Name: Two options are available:

Select an application: Select one from the drop-down list directly.

- Custom application: Custom application by yourself.

Trigger Port Start/Trigger Port End: The port range for an application to initiate connections.

Trigger Protocol: Select the protocol from the drop-down list. If you are unsure, select TCP/UDP.

Open Port Start/ Open Port End: These are the starting number and ending number for the ports that will be

85

automatically opened by the built-in firewall when connections initiated by an application are established.

DMZ Host

The default DMZ (De-Militarized Zone) host feature is helpful when you are using some online games and

videoconferencing applications that are not compatible with NAT (Network Address Translation).

DMZ Host IP Address: The IP Address of the device for which the router’s firewall will be disabled. Be sure to assign a

static IP Address to that device. The DMZ host should be connected to a LAN port of the device. Be sure to assign a

static IP address to that DMZ host.

Warning!

DMZ servers pose a security risk. A computer designated as the DMZ server loses much of the protection of the firewall

and is exposed to exploits from the Internet.

UPnP

UPnP (Universal Plug and Play) allows Windows based systems to configure the device for various Internet applications

automatically. UPnP devices can automatically discover the services from other registered UPnP devices on the network.

If you use applications such as multiplayer gaming, peer-to-peer connections, or real-time communications, like instant

messaging or remote assistance (a feature in Windows XP), you should enable UPnP.

86

Enable UPnP: Check/uncheck to enable/disable the UPnP feature.

_________________________________________________________________________________________________

NOTE

UPnP is activated only when there is a live WAN service with NAT enabled.

_________________________________________________________________________________________________

4.2.5 Security

This section explains the following information:

• IP Filtering

• MAC Filtering

IP Filtering

Outgoing IP Filtering Setup

By default, all outgoing IP traffic from LAN is allowed, but some IP traffic can be BLOCKED by setting up filters.

Choose Add or Remove to configure outgoing IP filters.

Choose Add to enter the following screen:

87

This screen allows you to create a filter rule to identify outgoing IP traffic by specifying a new filter name and at least

one condition below. All of the specified conditions in this filter rule must be satisfied for the rule to take effect. Click

to save and activate the filter.

 Filter Name: Enter a descriptive filtering name.

 IP Version: Support IPv4.

 Protocol: TCP/UDP, TCP, UDP and ICMP are available for your option.

 Source IP address [/prefix length]: Enter the LAN IP address to be filtered.

 Source Port (port or port: port): Specify a port number or a range of ports used by LAN PCs to access the

Internet. If you are unsure, leave it blank.

 Destination IP address [/prefix length]: Specify the external network IP address to be accessed by specified LAN

PCs.

 Destination Port

(port or port:port): Specify a port number or a range of ports used by LAN PCs to access external

network.

Incoming IP Filtering Setup

When the firewall is enabled on a WAN or LAN interface, all incoming IP traffic is BLOCKED. However, some IP

traffic can be ACCEPTED by setting up filters.

Choose Add or Remove to configure incoming IP filters.

88

Click Add to enter the following screen:

This screen allows you to create a filter rule to identify incoming IP traffic by specifying a new filter name and at least

one condition below. All of the specified conditions in this filter rule must be satisfied for the rule to take effect. Click

to save and activate the filter.

 IP Version: Select IP version.

 Protocol: TCP/UDP, TCP, UDP and ICMP are available for your option.

 Source IP address [/prefix length]: Enter the Internal IP address [/prefix length] to be filtered.

 Source Port (port or port: port): Specify a port number or a range of ports used by PCs from external network to

access your internal network.

 Destination IP address [/prefix length]: Specify the internal network IP address [/prefix length] to be accessed by

the specified PCs from external network.

 Destination Port

(port or port:port): Specify a port number or a range of ports used by PCs from external network

to access your internal network.

MAC Filtering

A bridge WAN service is needed to configure this service.

MAC Filtering is only effective on ATM PVCs configured in Bridge mode. FORWARDED means that all MAC layer

frames will be forwarded except those matching with any of the specified rules in the following table. BLOCKED means

that all MAC layer frames will be blocked except those matching with any of the specified rules in the following table.

Choose Add or Remove to configure MAC filtering rules.

89

_________________________________________________________________________________________________

Warning!

Changing from one policy to another of an interface will cause all defined rules for that interface to be REMOVED

AUTOMATICALLY! You will need to create new rules for the new policy.

_________________________________________________________________________________________________

Click Add to enter the following screen:

Here you can create a filter to identify the MAC layer frames by specifying at least one condition below. If multiple

conditions are specified, all of them take effect. Click Save/Apply to save and activate the filter.

Protocol Type: Select a protocol type from the drop-down list.

Destination MAC Address: Enter the MAC address of data frame being restricted to arrive.

Source MAC Address: Enter the MAC address of data frame being restricted to come.

Frame Direction: Select a frame direction from the drop-down list.

WAN Interfaces: Select a WAN interface from the drop-down list.

4.2.6 Parental Control

This section explains the following information:

90

• Time Restriction

• URL Filter

Time Restriction

Click Parental Control > Time Restriction > Add to enter the following screen.

Here you can add time of day restriction that an attached LAN device can access the Internet.

The Browser's MAC Address automatically displays the MAC address of the LAN device where the browser is running.

To restrict other LAN device, check the "Other MAC Address" option and enter its MAC address.

 User Name: Enter a user name.

 Browser's MAC Address: Automatically adds the MAC address of the attached LAN device where the browser is

running.

 Other MAC Address: Specify the MAC address of the computer that you want to apply Internet access restriction.

 Days of the week: Click to select the days of the week during which you wish to restrict Internet access.

 Start Blocking Time/ End Blocking Time: Specify time of day restriction to an attached LAN device. Within this

specified time length of the day, this LAN device will be blocked from the Internet.

 Apply/Save: Click

to save and apply your settings.

URL Filter

Here you can add URL access restriction to specific LAN PCs.

91

Select the URL List Type (Exclude or Include) first and then click Add to enter the screen below for configuring the list

entries.

URL Address: Enter a specific URL or a key word of domain name in this field.

Click

to apply and save the settings.

_________________________________________________________________________________________________

NOTE

If you have accessed the URL before you include it in a URL filter rule, you must reboot the router and erase it from

your PC to activate this URL filter rule. To erase the domain name from your PC:

1. Click the keys +R on the keyboard to enable “Run” dialog, and type cmd > click OK.

(Note that different operation systems may have different ways to enable “Run”; Windows is taken a guide here.)

92

2. Then type ipconfig /flushdns and hit Enter on the keyboard.

_________________________________________________________________________________________________

4.2.7 Bandwidth Control

When multiple devices each of which requests a different bandwidth attach to the modem router, to ensure the attached

devices obtaining a fair bandwidth and getting a fluent Internet experience, set a bandwidth control rule.

Check Enable Bandwidth Control to enable this feature.

93

Description: Name the bandwidth control rule as you like.

IP Address Range: Type the IP address range of target hosts. Follow the example .

If you want to set one host, follow the example

Max Upstream Speed (Kbps): Set the upstream speed as your actual bandwidth need.

Max Downstream Speed (Kbps): Set the downstream speed as your actual bandwidth need.

Status: Enable or Disable.

After you have edited the details of the bandwidth control rule, click first to save and then click to

activate the settings.

.

4.2.8 Routing

This section explains the following:

• Default Gateway

• Static Route

Default Gateway

Default gateway interface list can have multiple WAN interfaces served as system default gateways but only one will be

used according to the priority with the first being the highest and the last one the lowest priority if the WAN interface is

connected. Priority order can be changed by removing all and adding them back in again.

 Selected Default Gateway Interfaces: Displays the selected default gateway interfaces. Select a WAN interface

and click the

button to move it to the Available Routed WAN Interfaces box.

94

 Available Routed WAN Interfaces: Displays the available routed WAN interfaces. Select a WAN interface and

click the button to add it to the Selected Default Gateway Interfaces box.

 Apply/Save: Click to save and activate your settings.

Static Route

Static routes provide additional routing information to your router. Typically, you do not need to add static routes.

However, when there are several routers in the network, you may want to set up static routing. Static routing determines

the path of the data in your network. You can use this feature to allow users on different IP domains to access the Internet

via this device. It is not recommended to use this setting unless you are familiar with static routing. In most cases,

dynamic routing is recommended, because this feature allows the router to detect the physical changes of the network

layout automatically.

Click Add to enter the following screen:

 IP Version: Select IP version.

 Destination IP address/prefix length: Enter the destination IP address and prefix length of the final destination.

 Interface:

Select an interface from the drop-down list.

 Gateway IP address: Enter the gateway IP address, which must be a router on the same LAN segment as the

95