Page 1
Wireless Modem Router
i
Page 2
Wireless Modem Router
Copyright Statement
is the registered trademark of Shenzhen Tenda Technology Co., Ltd. All the products and product names
mentioned herein are the trademarks or registered trademarks of their respective holders. Copyright of the whole product
as integration, including its accessories and software, belongs to Shenzhen Tenda Technology Co., Ltd. No part of this
publication can be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in
any form or by any means without the prior written permission of Shenzhen Tenda Technology Co., Ltd. If you would
like to know more about our product information, please visit our website at http://www.tendacn.com.
Disclaimer
Pictures, images and product specifications herein are for references only. To improve internal design, operational
function, and/or reliability, Tenda reserves the right to make changes to the products without obligation to notify any
person or organization of such revisions or changes. Tenda does not assume any liability that may occur due to the use or
application of the product described herein. Every effort has been made in the preparation of this document to ensure
accuracy of the contents, but all statements, information and recommendations in this document do not constitute the
warranty of any kind, express or implied.
Technical Support
Website: http://www.tendacn.com
Telephone: (86 755) 2765 7180
Email: support@tenda.com.cn
ii
Page 3
Wireless Modem Router
Contents
Chapter 1 Get to Know Your Wireless Router ................................................................ ........................................ 1
1.1 What it does ......................................................................................................................................... 1
1.2 Product Features ................................................................................................................................... 1
1.3 Package Contents .................................................................................................................................. 2
Chapter 2 Hardware Install ................................................................................................................................. 2
Chapter 3 Quick Internet Setup............................................................................................................................ 5
3.1 Log in to Web Manager .......................................................................................................................... 5
Using Setup Wizard ............................................................................................................................. 5
Using Browser .................................................................................................................................... 5
3.2 Internet Setup ................................ ................................................................................................ ....... 6
ADSL ................................................................................................................................................ 6
ETH................................................................................................................................................... 7
3.3 Quick Wireless Security Setup ................................................................................................................ 9
Chapter 4 Advanced Settings............................................................................................................................. 10
4.1 Device Info ........................................................................................................................................ 10
4.2 Advanced Setup .................................................................................................................................. 15
4.2.1 Layer2 Interface ................................ ........................................................................................ 15
4.2.2 WAN Service ............................................................................................................................ 18
4.2.3 LAN Setup ............................................................................................................................... 47
4.2.4 NAT................................................................................................ ......................................... 49
4.2.5 Security ................................................................................................................................ .... 54
4.2.6 Parental Control ........................................................................................................................ 57
4.2.7 Quality of Service ...................................................................................................................... 59
4.2.8 Routing ................................................................................................ .................................... 62
4.2.9 DNS ........................................................................................................................................ 64
4.2.10 DSL ....................................................................................................................................... 68
4.2.11 UPnP...................................................................................................................................... 69
4.2.12 Print Server (Available only in D301) ................................................................ ......................... 70
4.2.13 Storage Service (Available only in D301) .................................................................................... 70
4.2.14 Interface Grouping ................................................................................................................... 72
4.2.15 IP Tunnel ................................................................................................................................ 73
4.2.16 Certificate ............................................................................................................................... 75
4.2.17 Multicast................................................................................................................................. 78
4.2.18 IPTV ...................................................................................................................................... 79
4.3 Wireless ................................................................ ............................................................................. 80
4.3.1 Basic................................................................................................................................ ........ 80
4.3.2 Security ................................................................................................................................ .... 81
4.3.3 MAC Filter ............................................................................................................................... 82
4.3.4 Wireless Bridge ......................................................................................................................... 83
4.3.5 Station Info ............................................................................................................................... 84
4.4 Diagnostics......................................................................................................................................... 84
4.5 Management ....................................................................................................................................... 85
4.5.1 Settings .................................................................................................................................... 85
4.5.2 System Logs ................................................................ ............................................................. 86
4.5.3 Security Log ............................................................................................................................. 87
4.5.4 SNMP Agent ................................................................................................ ............................. 88
iii
Page 4
Wireless Modem Router
4.5.5 TR-069 Client ................................................................ ........................................................... 88
4.5.6 Internet Time............................................................................................................................. 89
4.5.7 Access Control .......................................................................................................................... 89
4.5.8 Update Software ........................................................................................................................ 91
4.5.9 Reboot ..................................................................................................................................... 92
Appendix 1 Configure Your PC ......................................................................................................................... 93
Windows 7 ................................................................ .............................................................................. 93
MAC ...................................................................................................................................................... 95
Appendix 2 Join Your Wireless Network............................................................................................................. 97
Windows XP............................................................................................................................................ 97
Windows 7 ................................................................ .............................................................................. 98
MAC .....................................................................................................................................................100
iPhone/iPad ............................................................................................................................................101
Appendix 3 FAQs ...........................................................................................................................................103
Appendix 4 VPI/VCI List ................................................................................................................................105
Appendix 5 Regulatory Compliance Information ................................................................................................ 111
iv
Page 5
Wireless Modem Router
Model
Wireless Speed
USB Port
RJ45 Port
D301v2.0
300M
0
4
D151v2.0
150M
0
4
Chapter 1 Get to Know Your Wireless Router
This user guide applies to the following four models: D301, D302, D151 and D152. The D301 is used as an example
throughout this user guide. The differences between the four products are listed below:
D301v2.0 D151v2.0
_________________________________________________________________________________________________
Note:
The USB-based features of Print Server and Storage Service are unavailable in D151, D152 and D302 which are not
built with a USB port.
_________________________________________________________________________________________________
1.1 What it does
The Wireless ADSL2+ Modem Router provides you with an easy and secure way to set up a wireless home network with
fast access to the Internet over a high-speed digital subscriber line (DSL). Complete with a built-in ADSL modem, it is
compatible with all major ADSL Internet service providers. It offers wireless speeds of up to 300Mbps needed for
demanding applications, such as large file transfers, streaming HD video, and multiplayer gaming. The unit comes with a
wide range of premium features and applications such as IPv6, TR069, SNMP, Multicast, IP tunnel, ready share USB,
IPTV service and parental controls, etc. Plus, with the router, you can access Internet via the ATM interface or Ethernet
interface.
1.2 Product Features
Wireless N speeds up to 300 Mbps for streaming HD videos and online gaming in addition to basic Internet applications.
All-in-one device combines a Built-in ADSL2+ modem, wired router, wireless router and switch
Sharable USB lets you access and share files on an attached USB hard drive (available only in D301)
1
Page 6
Wireless Modem Router
Sharable Printer lets you print from your Windows computer to a connected USB printer (available only in D301)
Advanced QoS helps prioritize media streaming and gaming applications for best entertainment experience
Parental Control keeps your kids Internet experience safe using flexible and customizable filter settings
One-touch WPS ensures a quick and secure network connection
WEP and WPA/WPA2 are supported for advanced encryptions
Compatibility: Works with all major ADSL Internet service providers (ISPs); backward compatible with 802.11b/g WiFi
devices
Interchangeable LAN/WAN ports to schedule the Ethernet port to function either as a LAN or a WAN port
Interchangeable LAN/IPTV to schedule the Ethernet port to function either as a LAN or an IPTV port
Optional Ethernet and ADSL Uplinks: Access Internet via ADSL2+ Broadband Internet Service or an interchangeable
LAN/WAN RJ-45 port
Multiple Internet Connection Types: Bridging, PPPoE, IPoE, PPPoA, IPoA, dynamic IP and static IP
IPTV Service lets your surf Internet while watching online TV
6000V lightning－ proof design fits into lightning-intensive environment
Strong driving capability up to 6.5Km transmission distance
High speed ADSL speed up to 24Mbps downstream 1Mbps upstream
Built-in firewall prevents hacker attacks
Channel auto-select for optimum performance
FDM technology enables telephoning, faxing and surfing activities to proceed simultaneously without mutual
interference
Other Advanced Features: IPv6, DDNS, virtual server, DMZ, port triggering, IP filter, MAC filter and UPnP, etc.
Tenda Setup Wizard for easy and fast installation and configuration
Tenda Green: Use hardware Power On/Off and software WiFi On/Off buttons to turn on and off power and WiFi to save
energy when not in use
1.3 Package Contents
Your box should contain the following items:
Wireless Modem Router
Phone cable
Ethernet cable
ADSL2+ filter
Install Guide
Power adapter
Resource CD
If any of the parts are incorrect, missing, or damaged, keep the carton, including the original packing materials and
contact your Tenda dealer for immediate replacement.
Chapter 2 Hardware Install
If you have not already set up your new router using the Install Guide that comes in the box, this chapter walks you
through the hardware install. To set up your Internet connection, see Chapter 3 Quick Internet Setup.
Front Panel
2
Page 7
Wireless Modem Router
LED
Status
Description
PWR
Solid
Power is supplied to the device.
Off
Power is not supplied to the device.
SYS
Blinking
System is functioning correctly.
Solid/Off
System is functioning incorrectly.
WLAN
Blinking
Transmitting data wirelessly
Off
Wireless is disabled.
Solid
Wireless is enabled.
DSL
Slow Blinking
Physical connection failure.
Fast Blinking
Synchronizing...
Solid
ADSL connection is established.
LAN 1/2/3/4
Off
No connection established.
Blinking
Transmitting data
Solid
Connection is established.
WPS
Solid
Client connected successfully.
Blinking
The WPS LED starts blinking if you press the WPS button on the device or
interface.
Off
If there is no wireless clients connected, the WPS LED turns off after blinking for
2 minutes.
USB
(available
only in D301)
Solid
Connection is successfully established on the USB port.
Off
Connection is not established on the USB port.
INTERNET
Solid
The current Internet client is connecting to the Internet but no data is transmitted
The LEDs on the device are described below:
3
Page 8
Wireless Modem Router
Button & Interface
Description
DSL
RJ11 port, for connecting the router to the Internet via a telephone line provided by your ISP.
1
LAN port or WAN port. When you access the Internet via the DSL, this port works as a LAN
port which can be used to connect to a PC, switch, or a router; when you access the Internet
via an Ethernet cable from your ISP directly, this port works as a WAN port.
Note: It works as a LAN port by default.
2/3
LAN port, used to cable the device to the local network devices such as computers.
4
LAN port or IPTV port. When IPTV feature is disabled, it works as a LAN port which can be
used to connect to a PC, switch or a router; when IPTV feature is enabled, it works as a IPTV
port, and it can only be connected to a Set-Top Box.
Note: IPTV feature is disabled by default.
USB
Used to connect a USB device, such as a 3G USB modem, USB print server or storage
service.
WPS/RST
Press it for 1-3 seconds to enable WPS-PBC feature;
Press it for 10 seconds to restore all configurations to factory defaults.
PWR
Used to connect to the power adapter, which is included in the package.
ON/OFF
Power switch to turn the router on or off.
via the Internet.
Blinking
The current Internet client is connecting to the Internet and data is transmitted via
the Internet.
Off
The current Internet client is not connecting to the Internet.
Back Panel
_________________________________________________________________________________________________
Note:
Please use the included power adapter. Use of a power adapter with different voltage rating may damage the device.
_________________________________________________________________________________________________
Follow the diagram below to install the device.
4
Page 9
Wireless Modem Router
Chapter 3 Quick Internet Setup
This chapter instructs you to quickly set up your Internet connection.
3.1 Log in to Web Manager
You can log in to the modem router ’s web manager with the Setup Wizard on the included CD automatically or using a
web browser manually. The Setup Wizard on the auto-run CD can automatically configure your PC’s TCP/IP properties
and direct you to the web login window without requiring the IP address.
Using Setup Wizard
Before using the Setup Wizard, you should connect your router to the computer first, i.e., finish the Hardware Install.
1. Insert the included resource CD into your computer ’s drive and the CD automatically runs. If the CD does not run
automatically, double click . You will see the screen below.
2. Select the responding product model, and click Start Setup and operate according to the onscreen instructions to set
the router. If you want to read the product’s user guide, click the responding product’s User Guide.
Using Browser
1. Set your PC to Obtain an IP address automatically. For more information, see Appendix 1 Configure Your
PC.
2. Launch a web browser and enter 192.168.1.1 to display the login window.
5
Page 10
Wireless Modem Router
3. Enter admin in both the Login Username and Password fields if you access the router for the first time and then click
Login to enter the home page.
_________________________________________________________________________________________________
Tip:
If you change the login username and password and forget them, press the WPS/RST button on the device for at least 7
seconds to reset the router, and then enter the home page with the default password “admin”.
_________________________________________________________________________________________________
3.2 Internet Setup
ADSL
1. Link Type: Select ADSL.
2. Select your country.
3. Select your ISP.
4. VPI and VCI fields will be populated automatically if you select a correct country and ISP.
5. Select your Connection Type, and fill the relevant Internet information, like PPPoE username and password
from your ISP.
6. Configure your wireless network. (Recommended)
Setup your SSID.
Setup your wireless key.
7. Click OK to apply your configurations.
6
Page 11
Wireless Modem Router
Connection Type
ISP Information
PPPoE/ PPPoA
Enter the ISP login user name and password. If you cannot locate this information, ask your ISP
to provide it.
IPoE
Dynamic IP
No entries are needed.
Static (Fixed) IP
Enter the assigned IP address, subnet mask, and the IP address of your ISP’s primary DNS
server. This information should have been provided to you by your ISP. If a secondary DNS
server address is available, enter it also.
IPoA
Static (Fixed) IP
Enter the assigned IP address, subnet mask, and the IP address of your ISP’s p rimary DNS
server. This information should have been provided to you by your ISP. If a secondary DNS
server address is available, enter it also.
Bridge
When Bridge mode is enabled, this device works as a modem. If you wish to initiate a dialup
directly from your PC for Internet access or enjoy the entire Internet connection by yourself
(instead of sharing it with others), you can select the Bridge.
Depending on the type of connection, you are prompted to enter your ISP settings, as shown in the following table:
ETH
1. Link Type: Select ETH.
2. Select your connection type according to your accessing method.
7
Page 12
Wireless Modem Router
Connection Type
ISP Information
PPPoE
Enter the ISP login user name and password. If you cannot locate this information, ask
your ISP to provide it.
IPoE
Dynamic IP
No entries are needed.
Static (Fixed) IP
Enter the assigned IP address, subnet mask, and the IP address of y our ISP’s p rimary
DNS server. This information should have been provided to you by your ISP. If a
secondary DNS server address is available, enter it also.
Bridge
When Bridge mode is enabled, this device works as a modem. If you wish to initiate a
dialup directly from your PC for Internet access or enjoy the entire Internet connection
(instead of sharing it with others), you can select the Bridge.
3. Configure your wireless network. (Recommended)
4. Setup your SSID.
5. Setup your wireless key.
6. Click OK to apply your configurations.
Depending on the type of connection, you are prompted to enter your ISP settings, as shown in the following table:
_________________________________________________________________________________________________
Note:
If your country and/or your ISP are not covered on the home page, please click the button on the
home page and then select Advanced Setup -> Layer2 Interface -> ATM Interface and then click Add there to manually
configure the VPI and VCI. If you cannot locate this information, refer to Appendix 4 VPI/VCI List or ask your ISP to
provide it. For more information, see To Set up the ATM interface and To Set up WAN Service for ATM Interface.
_________________________________________________________________________________________________
f. After you configure all the above settings, click OK to save and apply them.
8
Page 13
Wireless Modem Router
g. Test Internet Connectivity
Launch a web browser and enter www.tendacn.com. If the webpage displays properly, you are connected to the Internet.
3.3 Quick Wireless Security Setup
For security purpose, we strongly recommend you to customize a new security key. Simply enter 8-63 ASCII or 64 hex
characters.
_________________________________________________________________________________________________
Tip:
1. If you customize a new security key, write it on a sticky label and attach it to the bottom of the unit. You will need the
new security key if you wish to connect to the device wirelessly in the future.
2. To join your secured wireless network, see Appendix 2 Join Your Wireless Network.
_________________________________________________________________________________________________
9
Page 14
Wireless Modem Router
Chapter 4 Advanced Settings
This chapter describes the advanced features of your router.
The information is for users with a solid understanding of networking concepts who want to configure the router for
unique situations.
This chapter includes the following sections:
• Device Info
• Advanced Setup
• Wireless
• Diagnostics
• Management
Click Advanced on the home page to enter the screen below.
4.1 Device Info
This section includes the following information:
10
Page 15
Wireless Modem Router
• Summary
• WAN
• Statistics
• Route
• ARP
• DHCP
Summary
Here you can view system information and current status of your WAN connection as seen in the screenshot.
WAN
Here you can view the WAN Information including Interface, Description, Type, IGMP, NAT, Firewall, Status, IPv4
Address and VLAN ID as seen in the screenshot.
11
Page 16
Wireless Modem Router
Statistics
Here you can view the packets received and transmitted on LAN/WAN ports.
Statistics--LAN: Displays the packets received and transmitted on the LAN ports as seen in the screenshot below.
_________________________________________________________________________________________________
Tip:
eth0, eth1, eth3 and eth3 respectively represent the LAN port1, LAN port2, LAN port3 and LAN port4 of the device.
_________________________________________________________________________________________________
Statistics--WAN: Displays the packets received and transmitted on the WAN ports as seen in the screenshot below.
12
Page 17
Wireless Modem Router
Route
Here you can view the route table as seen in the screenshot:
ARP
Here you can view the IP and MAC addresses of the PCs that attach to the device either via a wired or wireless
connection as seen in the screenshot:
13
Page 18
Wireless Modem Router
DHCP
Here you can view the DHCP leases, including IP and MAC addresses of the PCs, hostnames and remaining lease time
as seen in the screenshot:
14
Page 19
Wireless Modem Router
4.2 Advanced Setup
This section explains the following information:
• Layer2 Interface
• WAN Service
• LAN
• NAT
• Security
• Parental Control
• Quality of Service
• Routing
• DNS
• DSL
• UPnP
• Print Server
• Storage Service
• Interface Grouping
• IP Tunnel
• Certificate
• Multicast
• IPTV
4.2.1 Layer2 Interface
Click Advanced Setup -> Layer2 Interface to enter the Layer2 Interface screen.
This router provides two Layer2 Interfaces:
- ATM Interface for ADSL broadband Internet service
- ETH Interface for connecting to the Internet via an Ethernet cable.
By default, system applies the ATM Interface (ADSL uplink).
If you directly connect to the ADSL line via a phone cable, first refer to To Set up the ATM interface and then skip to
To Set up WAN Service for ATM Interface.
Or if you connect to the Internet via a fiber/cable modem using an Ethernet cable, first refer to To Set up the ETH
interface and then skip to To Set up WAN Service for ETH Interface.
15
Page 20
Wireless Modem Router
To set up the ATM interface
Select ATM Interface and click Add to configure it.
Enter the VPI and VCI values, Select a DSL Link Type (Internet connection type): EoA (EoA is for PPPoE, IPoE, and
Bridge.), PPPoA or IPoA, leave other options unchanged from factory defaults and click Apply/Save and then refer to
16
Page 21
Wireless Modem Router
To Set up WAN Service for ATM Interface to configure the WAN service for Internet access.
_________________________________________________________________________________________________
Tip:
If you are unsure about the VPI/VCI parameters, see Appendix 4 VPI/VCI List. Or if your ISP and the VPI/VCI
information is not covered there, ask your ISP to provide it.
_________________________________________________________________________________________________
To set up the ETH interface
Select ETH Interface and click Add to configure it.
The Ethernet port configured here is to function as a WAN port. Only one LAN port can be configured as the WAN port
at a time. After you finish your settings, click the Apply/Save button and then refer to To Set up WAN Service for ETH
Interface to configure the WAN service for Internet access.
_________________________________________________________________________________________________
Tip:
eth0, eth1, eth3 and eth3 respectively represent the LAN port1, LAN port2, LAN port3 and LAN port4 of the device.
_________________________________________________________________________________________________
17
Page 22
Wireless Modem Router
Internet Connection Type
ISP Information
PPPoE/PPPoA
Enter the ISP login user name and password. If you cannot locate
this information, ask your ISP to provide it.
IPoE
(If your ISP uses DHCP to assign
your IP address or if your ISP
assigns you a static (fixed) IP
address, IP subnet mask and the
gateway IP address, you need to
select the IP over Ethernet (IPoE).
Dynamic IP
No entries are needed.
Static (Fixed) IP
Enter the assigned IP address, subnet mask, and the IP address of
your ISP’s primary DNS server. This information should have been
provided to you by your ISP. If a secondary DNS server address is
available, enter it also.
IPoA
Static (Fixed) IP
Enter the assigned IP address, subnet mask, and the IP address of
your ISP’s primary DNS server. This information should have been
provided to you by your ISP. If a secondary DNS server address is
available, enter it also.
Bridging
If you wish to initiate a dialup directly from your PC for Internet
access or enjoy the entire Internet connection (instead of sharing it
with others), you can select the Bridging and then click Next.
4.2.2 WAN Service
This router provides two WAN services:
- WAN Service for ATM Interface (ADSL uplink)
- WAN Service for ETH Interface (Ethernet uplink)
To Set up WAN Service for ATM Interface
If you configured the ATM Interface (ADSL uplink), follow steps below to configure the WAN service:
Click Advanced Setup -> WAN Service and then click the Add button. Select the interface you have configured.
Depending on the type of connection, you will come to different screens and be prompted to enter your ISP settings
accordingly. Select one connection type from the five Internet connection types as shown in the following table (If you
are unsure, consult your ISP.):
_________________________________________________________________________________________________
Tip:
For PPPoE, IPoE, and Bridging Internet connection types, you must first select EoA on the ATM Interface Screen. For
more information, see To Set up the ATM interface.
_________________________________________________________________________________________________
PPP over Ethernet (PPPoE)
If you have selected the EoA from the ATM Interface screen in Layer2 Interface, you will see the screen below when
you click the WAN Service tab, select the configured interface and click Next.
18
Page 23
Wireless Modem Router
1. Select PPPoE.
2. Edit the Enter Service Description. This field is optional. We recommend that you keep the default.
3. Select a network protocol: IPv4, IPv6 or IPv4 & IPv6 (dual stack).
4. Click Next.
_________________________________________________________________________________________________
Note:
If you select IPv6 or IPv4 & IPv6 (dual stack), skip to IPv6.
_________________________________________________________________________________________________
19
Page 24
Wireless Modem Router
PPP Username: This is for logging in to your ISP. If you cannot locate this information, ask your ISP to provide it.
PPP Password: This is for logging in to your ISP. If you cannot locate this information, ask your ISP to provide it.
PPPoE Service Name: This information is provided by your ISP. Only enter it if instructed by your ISP.
Authentication Method: This is used by ISP to authenticate the client that attempts to connect. If you are not sure,
consult your ISP or select Auto.
MAC Clone: Clicking this button copies the MAC address of your PC to the router. Many broadband ISPs restrict
access by allowing traffic only from the MAC address of your broadband modem, but some ISPs additionally register the
MAC address of the network interface card in your computer when your account is first opened. They then accept traffic
only from the MAC address of that computer. If so, configure your router to “clone” the MAC address from the
authorized computer.
MTU: Short for Maximum Transmission Unit, the largest physical packet size, measured in bytes, which a network can
transmit. Any messages larger than the MTU are divided into smaller packets before being sent. The default MTU is
1492 bytes. For some ISPs, you might need to change the MTU. This is rarely required, and should not be done unless
you are sure it is necessary for your ISP connection.
Dial on demand: Connect to ISP only when there is traffic transmission. This saves your broadband Internet service bill.
PPP IP extension: If enabled, all the IP addresses in outgoing packets including management packets on the WAN port
will be changed to the device's WAN IP address. Only change the default settings if necessary.
Enable PPP Debug Mode: Only enable this feature if supported by your ISP.
Bridge PPPoE Frames Between WAN and Local Ports: If enabled, PPPoE dialup frame from LAN side will directly
egress the WAN port without modification.
Multicast Proxy: If enabled, the router will use multicast proxy.
IPv6
If you select IPv4 as the network protocol, skip this section.
Check Launch Dhcp6c for Prefix Delegation (IAPD).
If your ISP is using stateful DHCPv6, check Launch Dhcp6c for Address Assignment (IANA) also. Or configure a
static IP address.
Click Next -> Next -> Apply/Save.
20
Page 25
Wireless Modem Router
WAN Gateway
Here you can configure the WAN gateway address. After you configure it click Next. The default setting is
recommended.
_________________________________________________________________________________________________
Note:
Default gateway interface list can have multiple WAN interfaces served as system default gateways but only one will be
used according to the priority with the first being the highest and the last one the lowest priority if the WAN interface is
connected. Priority order can be changed by removing all and adding them back in again.
_________________________________________________________________________________________________
WAN DNS
Here you can configure the WAN DNS address:
-Click the Select DNS Server Interface from available WAN interfaces option
-Or select the Use the following Static DNS IP address option and enter static DNS server IP addresses for the system
And then click Next.
_________________________________________________________________________________________________
Note:
21
Page 26
Wireless Modem Router
1.DNS Server Interfaces can have multiple WAN interfaces served as system DNS servers but only one will be used
according to the priority with the first being the highest and the last one the lowest priority if the WAN interface is
connected. Priority order can be changed by removing all and adding them back in again.
2. In ATM mode, if only a single PVC with IPoA or static IPoE protocol is configured, Static DNS server IP addresses
must be entered.
3. If you cannot locate the static DNS server IP information, ask your ISP to provide it.
_________________________________________________________________________________________________
Here you can view your configurations. Click Apply/Save to save your settings if everything is correctly set.
When the PPPoE connection is successful, you can access the Internet.
IP over Ethernet (IPoE)
If your ISP uses DHCP to assign your IP address or if your ISP assigns you a static (fixed) IP address, IP subnet mask
and the gateway IP address, you need to select the IP over Ethernet (IPoE).
If you have selected the EoA from the ATM Interface screen in Layer2 Interface, you will see the screen below when
you click the WAN Service tab, select the configured interface and click Next.
22
Page 27
Wireless Modem Router
Select IPoE.
Edit the Enter Service Description. This field is optional. We recommend that you keep the default.
Select a network protocol: IPv4, IPv6 or IPv4 & IPv6 (dual stack).
Click Next.
_________________________________________________________________________________________________
Note:
If you select IPv6 or IPv4 & IPv6 (dual stack), skip to IPv6.
_________________________________________________________________________________________________
Obtain an IP address automatically: This allows the router to automatically acquire IP information from your ISP or
your existing networking equipment.
Use the following Static IP address: This allows you to specify the Static IP information provided by your ISP or that
23
Page 28
Wireless Modem Router
corresponds with your existing networking equipment.
WAN IP Address: The Internet IP address provided by your ISP for accessing Internet.
WAN Subnet Mask: The subnet mask address provided by your ISP for accessing Internet.
WAN gateway IP Address: The gateway IP address provided by your ISP for accessing Internet.
IPv6
If you select IPv4 as the network protocol, skip this section.
To obtain an IP address automatically:
Select Obtain an IP address automatically.
Check Launch Dhcp6c for Prefix Delegation (IAPD).
If your ISP is using stateful DHCPv6, check Launch Dhcp6c for Address Assignment (IANA) also.
Click Next -> Next -> Apply/Save.
24
Page 29
Wireless Modem Router
To configure a static IPv6 address
Select Use the following Static IPv6 address.
Configure WAN IPv6 Address/Prefix Length and WAN Next-Hop IPv6 Address.
Click Next -> Next to enter the screen below.
Select Use the following Static IPv6 DNS address and manually enter the DNS server address. If you have two DNS
server addresses, enter the second also.
Click Next -> Apply/Save.
_________________________________________________________________________________________________
Note:
If "Obtain an IP address automatically" is chosen, DHCP will be enabled for PVC in IPoE mode.
_________________________________________________________________________________________________
25
Page 30
Wireless Modem Router
Here you can configure the NAT settings. If you are unsure about the options, please keep the default settings and then
click Next.
Here you can configure the WAN gateway address. Default gateway interface list can have multiple WAN interfaces
served as system default gateways but only one will be used according to the priority with the first being the highest and
the last one the lowest priority if the WAN interface is connected. Priority order can be changed by removing all and
adding them back in again.
If you are unsure about the options, please keep the default settings and then click Next.
26
Page 31
Wireless Modem Router
Here you can configure the WAN DNS address:
-Click the Select DNS Server Interface from available WAN interfaces option
-Or select the Use the following Static DNS IP address option and enter static DNS server IP addresses for the system
And then click Next.
_________________________________________________________________________________________________
Note:
1. DNS Server Interfaces can have multiple WAN interfaces served as system DNS servers but only one will be used
according to the priority with the first being the highest and the last one the lowest priority if the WAN interface is
connected. Priority order can be changed by removing all and adding them back in again.
2. In ATM mode, if only a single PVC with IPoA or static IPoE protocol is configured, Static DNS server IP addresses
must be entered.
3. If you cannot locate the static DNS server IP information, ask your ISP to provide it.
_________________________________________________________________________________________________
Here you can view your configurations. Click Apply/Save to save your settings if everything is correctly set.
27
Page 32
Wireless Modem Router
When the IPoE connection is successful, you can access the Internet.
Bridging
If you wish to initiate a dialup directly from your PC for Internet access or enjoy the entire Internet connection (instead
of sharing it with others), you can use the Bridging DSL link type and create a dialup program on your PC.
If you have selected the EoA from the ATM Interface screen in Layer2 Interface, you will see the screen below when
you click the WAN Service tab, select the configured interface and click Next.
The Enter Service Description field is optional. We recommend that you keep it unchanged from default and click
Next.
28
Page 33
Wireless Modem Router
Here you can view your configurations. Click Apply/Save to save your settings if everything is correctly set.
When the bridging connection is successful, you can access the Internet.
_________________________________________________________________________________________________
Note:
To configure multiple WAN connections, simply configure multiple ATM interfaces and then follow the instructions
above.
_________________________________________________________________________________________________
PPPoA
If you have selected the PPPoA from the ATM Interface screen in Layer2 Interface, you will see the screen below
when you click the WAN Service tab, select the configured interface and click Next.
29
Page 34
Wireless Modem Router
Edit the Enter Service Description. This field is optional. We recommend that you keep the default.
Select a network protocol: IPv4, IPv6 or IPv4 & IPv6 (dual stack).
Click Next.
PPP Username: This is for logging in to your ISP. If you cannot locate this information, ask your ISP to provide it.
PPP Password: This is for logging in to your ISP. If you cannot locate this information, ask your ISP to provide it.
Authentication Method: This is used by ISP to authenticate the client that attempts to connect. If you are not sure,
consult your ISP or select Auto.
Dial on demand: Connect to ISP only when there is traffic transmission. This saves your broadband Internet service bill.
Enable PPP Debug Mode: Only enable this feature if supported by your ISP.
Bridge PPPoE Frames Between WAN and Local Ports: If enabled, PPPoE dialup frame from LAN side will directly
egress the WAN port without modification.
Multicast Proxy: If enabled, the router will use multicast proxy.
If you are not sure about the options on this screen, simply enter your ISP user name and password and leave the other
options unchanged from defaults. Click Next to enter the following screen.
30
Page 35
Wireless Modem Router
WAN Gateway
Here you can configure the WAN gateway address. After you configure it click Next. The default setting is
recommended.
_________________________________________________________________________________________________
Note:
Default gateway interface list can have multiple WAN interfaces served as system default gateways but only one will be
used according to the priority with the first being the highest and the last one the lowest priority if the WAN interface is
connected. Priority order can be changed by removing all and adding them back in again.
_________________________________________________________________________________________________
WAN DNS
Here you can configure the WAN DNS address:
-Click the Select DNS Server Interface from available WAN interfaces option
-Or select the Use the following Static DNS IP address option and enter static DNS server IP addresses for the system
And then click Next.
31
Page 36
Wireless Modem Router
_________________________________________________________________________________________________
Note:
1. DNS Server Interfaces can have multiple WAN interfaces served as system DNS servers but only one will be used
according to the priority with the first being the highest and the last one the lowest priority if the WAN interface is
connected. Priority order can be changed by removing all and adding them back in again.
2. In ATM mode, if only a single PVC with IPoA or static IPoE protocol is configured, Static DNS server IP addresses
must be entered.
3. If you cannot locate the static DNS server IP information, ask your ISP to provide it.
_________________________________________________________________________________________________
Here you can view your configurations. Click Apply/Save to save your settings if everything is correctly set.
When the PPPoA connection is successful, you can access the Internet.
IPoA
If you have selected the IPoA from the ATM Interface screen in Layer2 Interface, you will see the screen above when
you click the WAN Service tab, select the configured interface and click Next.
32
Page 37
Wireless Modem Router
Edit the Enter Service Description. This field is optional. We recommend that you keep the default.
Click Next.
WAN IP Address: The Internet IP address provided by your ISP for accessing the Internet.
WAN Subnet Mask: The subnet mask address provided by your ISP for accessing the Internet.
Enter the WAN IP address and subnet mask assigned by your ISP. This information should have been provided to you by
your ISP. If you cannot locate this information, ask your ISP to provide it. And then click Next to enter the following
screen.
33
Page 38
Wireless Modem Router
If you are unsure about the options on the screen above, keep the defaults and click Next.
Here you can configure the WAN gateway address. After you configure it click Next. The default setting is
recommended.
______________________________________________________________________________________________
Note:
Default gateway interface list can have multiple WAN interfaces served as system default gateways but only one will be
used according to the priority with the first being the highest and the last one the lowest priority if the WAN interface is
connected. Priority order can be changed by removing all and adding them back in again.
______________________________________________________________________________________________
Here you can configure the WAN DNS address:
-Click the Select DNS Server Interface from available WAN interfaces option
-Or select the Use the following Static DNS IP address option and enter static DNS server IP addresses for the system
And then click Next to enter the following screen.
34
Page 39
Wireless Modem Router
_________________________________________________________________________________________________
Note:
1. DNS Server Interfaces can have multiple WAN interfaces served as system DNS servers but only one will be used
according to the priority with the first being the highest and the last one the lowest priority if the WAN interface is
connected. Priority order can be changed by removing all and adding them back in again.
2. In ATM mode, if only a single PVC with IPoA or static IPoE protocol is configured, Static DNS server IP addresses
must be entered.
3. If you cannot locate the static DNS server IP information, ask your ISP to provide it.
_________________________________________________________________________________________________
Confirm your settings and then click Apply/Save to apply and save your settings. Your settings will then be displayed on
the screen below:
To Set up WAN Service for ETH Interface
If you select and configured the ETH Interface (Ethernet uplink), follow steps below to configure the WAN service:
Two Internet connections: PPP over Ethernet (PPPoE) and IP over Ethernet (IPoE) are available in the Ethernet uplink
mode.
_________________________________________________________________________________________________
Tip:
eth0, eth1, eth3 and eth3 respectively represent the LAN port1, LAN port2, LAN port3 and LAN port4 of the device.
_________________________________________________________________________________________________
35
Page 40
Wireless Modem Router
PPP over Ethernet (PPPoE)
Click Advanced Setup -> WAN Service -> Add, select the configured interface and then click Next to enter the
following screen.
Select PPPoE.
Edit the Enter Service Description. This field is optional. We recommend that you keep the default.
Select a network protocol: IPv4, IPv6 or IPv4 & IPv6 (dual stack).
Click Next.
_________________________________________________________________________________________________
Note:
If you select IPv6 or IPv4 & IPv6 (dual stack), skip to IPv6.
_________________________________________________________________________________________________
36
Page 41
Wireless Modem Router
PPP Username: This is for logging in to your ISP. If you cannot locate this information, ask your ISP to provide it.
PPP Password: This is for logging in to your ISP. If you cannot locate this information, ask your ISP to provide it.
PPPoE Service Name: This information is provided by your ISP. Only enter it if instructed by your ISP.
Authentication Method: This is used by ISP to authenticate the client that attempts to connect. If you are not sure,
consult your ISP or select Auto.
MAC Clone: Clicking this button copies the MAC address of your PC to the router. Many broadband ISPs restrict
access by allowing traffic only from the MAC address of your broadband modem, but some ISPs additionally register the
MAC address of the network interface card in your computer when your account is first opened. They then accept traffic
only from the MAC address of that computer. If so, configure your router to “clone” the MAC address from the
authorized computer.
MTU: Short for Maximum Transmission Unit, the largest physical packet size, measured in bytes, which a network can
transmit. Any messages larger than the MTU are divided into smaller packets before being sent. The default MTU is
1492 bytes. For some ISPs, you might need to change the MTU. This is rarely required, and should not be done unless
you are sure it is necessary for your ISP connection.
Dial on demand: Connect to ISP only when there is traffic transmission. This saves your broadband Internet service bill.
PPP IP extension: If enabled, all the IP addresses in outgoing packets including management packets on the WAN port
will be changed to the device's WAN IP address. Only change the default settings if necessary.
Enable PPP Debug Mode: Only enable this feature if supported by your ISP.
Bridge PPPoE Frames Between WAN and Local Ports: If enabled, PPPoE dialup frame from LAN side will directly
egress the WAN port without modification.
Multicast Proxy: If enabled, the router will use multicast proxy.
If you are not sure about the options on this screen, simply enter your ISP user name and password and leave the other
options unchanged from defaults. Click Next.
IPv6
If you select IPv4 as the network protocol, skip this section.
37
Page 42
Wireless Modem Router
Check Launch Dhcp6c for Prefix Delegation (IAPD).
If your ISP is using stateful DHCPv6, check Launch Dhcp6c for Address Assignment (IANA) also. Or configure a
static IP address.
Click Next -> Next -> Apply/Save.
WAN Gateway
Here you can configure the WAN gateway address. After you configure it click Next. The default setting is
recommended.
38
Page 43
Wireless Modem Router
WAN DNS
Here you can configure the WAN DNS address. After you configure it click Next. The default setting is recommended if
you cannot locate this information.
Here you can configure the WAN DNS address:
-Click the Select DNS Server Interface from available WAN interfaces option
-Or select the Use the following Static DNS IP address option and enter static DNS server IP addresses for the system
And then click Next.
Here you can view your configurations. Click Apply/Save to save your settings if everything is correctly set.
39
Page 44
Wireless Modem Router
When the PPPoE connection is successful, you can access Internet.
IP over Ethernet (IPoE)
If your ISP uses DHCP to assign your IP address or if your ISP assigns you a static (fixed) IP address, IP subnet mask
and the gateway IP address, you need to select the IP over Ethernet (IPoE).
Click Advanced Setup -> WAN Service -> Add, select the configured interface and then click Next to enter the
following screen.
Select IPoE.
Edit the Enter Service Description. This field is optional. We recommend that you keep the default.
Select a network protocol: IPv4, IPv6 or IPv4 & IPv6 (dual stack).
Click Next.
_________________________________________________________________________________________________
Note:
If you select IPv6 or IPv4 & IPv6 (dual stack), skip to IPv6.
_________________________________________________________________________________________________
40
Page 45
Wireless Modem Router
Obtain an IP address automatically: This allows the router to automatically acquire IP information from your ISP or
your existing networking equipment.
Use the following Static IP address: This allows you to specify the Static IP information provided by your ISP or that
corresponds with your existing networking equipment.
WAN IP Address: The Internet IP address provided by your ISP for accessing Internet.
WAN Subnet Mask: The subnet mask address provided by your ISP for accessing Internet.
WAN gateway IP Address: The gateway IP address provided by your ISP for accessing Internet.
Enter the IP address/ subnet mask/gateway IP address provided by your ISP or select Obtain an IP address
automatically and then click the Next button.
IPv6
If you select IPv4 as the network protocol, skip this section.
41
Page 46
Wireless Modem Router
To obtain an IP address automatically:
Select Obtain an IP address automatically.
Check Launch Dhcp6c for Prefix Delegation (IAPD).
If your ISP is using stateful DHCPv6, check Launch Dhcp6c for Address Assignment (IANA) also.
Click Next -> Next -> Apply/Save.
To configure a static IPv6 address
Select Use the following Static IPv6 address.
Configure WAN IPv6 Address/Prefix Length and WAN Next-Hop IPv6 Address.
42
Page 47
Wireless Modem Router
Click Next -> Next to enter the screen below.
Select Use the following Static IPv6 DNS address and manually enter the DNS server address. If you have two DNS
server addresses, enter the second also.
Click Next -> Apply/Save.
43
Page 48
Wireless Modem Router
NAT
Here you can configure the NAT. If you are not an advanced user we recommend you to keep the default settings and
then click Next.
WAN Gateway
Here you can configure the WAN gateway address. After you configure it click Next. The default setting is
recommended.
WAN DNS
Here you can configure the WAN DNS address. After you configure it click Next. The default setting is recommended if
you cannot locate this information.
44
Page 49
Wireless Modem Router
Here you can configure the WAN DNS address:
-Click the Select DNS Server Interface from available WAN interfaces option
-Or select the Use the following Static DNS IP address option and enter static DNS server IP addresses for the system
And then click Next.
Here you can view your configurations. Click Apply/Save to save your settings if everything is correctly set.
When the IPoE connection is successful, you can access the Internet.
45
Page 50
Wireless Modem Router
Bridging
If you wish to initiate a dialup directly from your PC for Internet access or enjoy the entire Internet connection (instead
of sharing it with others), you can select the Bridging and create a dialup program on your PC.
Click Advanced Setup -> WAN Service -> Add, select the configured interface and then click Next to enter the
following screen.
Edit the Service Description, which is optional. And then click Next.
Here you can view your configurations. Click Apply/Save to save your settings if everything is correctly set.
46
Page 51
Wireless Modem Router
When the connection is successful, you can access the Internet.
4.2.3 LAN Setup
Here you can configure the LAN IP Address and Subnet Mask. This IP address is to be used to access the device’s
settings through a web browser. Be sure to make a note of any changes you apply to this page.
IPv4
IP Address: The device's LAN IP address. The default setting is 192.168.1.1.
Subnet Mask: The LAN subnet mask of the device. Combined with the IP address, the IP Subnet Mask allows a device
to know which other addresses are local to it, and which must be reached through a gateway or modem router. You can
change the subnet mask to fit your network.
Enable IGMP Snooping: Check to enable the IGMP Snooping feature and select either of the following two modes:
Configure the second IP Address and Subnet Mask for LAN interface: If you want to configure two IP addresses for
the LAN interface, you can check this option and enter the second IP Address and Subnet Mask manually.
Disable DHCP Server: Click to disable the DHCP Server.
47
Page 52
Wireless Modem Router
Enable DHCP Server: Click to enable the DHCP Server.
Start IP Address: Specify the start of the range for the pool of IP addresses in the same subnet as the router.
End IP Address: Specify the end of the range for the pool of IP addresses in the same subnet as the router.
Leased Time: The lease time is a time length that the IP address is assigned to each device before it is refreshed.
Static IP Lease List: Displays a list of devices with reserved static IP addresses.
Add Entries: Click to add a static IP lease entry. A maximum 32 entries can be configured.
Remove Entries: Click to remove a static IP lease entry.
Apply/Save: After you configure all the needed settings, click this button to apply and save them.
_________________________________________________________________________________________________
Tip:
DHCP (Dynamic Host Configuration Protocol) assigns an IP address to each device on the LAN/private network. When
you enable the DHCP Server, the DHCP Server will automatically allocate an unused IP address from the IP address
pool specified in this screen to the requesting device as long as the device is set to "Obtain an IP Address Automatically".
By default, the router functions as a DHCP server.
_________________________________________________________________________________________________
IPv6 Autoconfig
Static LAN IPv6 Address Configuration
Interface Address (prefix length is required): Enter the interface address.
_________________________________________________________________________________________________
Note:
1. IPv6 address can only be Aggregatable Global Unicast Addresses and Unique Local Address. Link-Local Unicast
Addresses and Multicast Addresses are not permitted.
2. The IPv6 address must be entered with a prefix length.
_________________________________________________________________________________________________
48
Page 53
Wireless Modem Router
IPv6 LAN Applications
Enable DHCPv6 Server：Check to enable the DHCPv6 Server.
Stateless: If selected, IPv6 clients will generate IPv6 addresses automatically based on the Prefix Delegation's IPv6
prefix and their own MAC addresses.
Stateful: Stateful DHCPv6 is supported based on the assumption of prefix length less than 64. Select this option and
configure the start/end interface ID and leased time. The router will automatically assign IPv6 addresses to IPv6 clients.
Leased Time (hour): The lease time is a time length that the IP address is assigned to each device before it is refreshed.
Start interface ID/End interface ID: Specify the start/end interface ID Interface ID does NOT support ZERO
COMPRESSION "::". Please enter the complete information. For example: Please enter "0:0:0:2" instead of "::2".
Enable RADVD: The RADVD (Router Advertisement Daemon) implements link-local advertisements of IPv6 router
addresses and IPv6 routing prefixes using the Neighbor Discovery Protocol (NDP) and is used by system administrators
in stateless autoconfiguration methods of network hosts on Internet Protocol version 6 networks. Check the checkbox to
enable the RADVD.
Enable ULA Prefix Advertisement: If enabled, the router will advertise ULA prefix periodically
Randomly Generate: If selected, address prefix can be automatically generated.
Statically Configure: If you select this option, you need to manually configure the address prefix and life time.
Prefix: Specify the prefix.
Preferred Life Time (hour): Specify the preferred life time in hour.
Valid Life Time (hour): Specify the valid life time in hour.
Enable MLD Snooping: MLD is used by IPv6 routers for discovering multicast listeners on a directly attached link. If
disabled on layer2 devices, IPv6 multicast data packets will be broadcast on the entire layer2; if enabled, these packets
will be multicast to only specified recipient instead of being broadcast on the entire layer2.
_________________________________________________________________________________________________
Tip:
If you change the LAN IP address of the device, you will lose your connection to the device. You must type the new IP
address into your browser address field to log in to the device and set all gateway addresses of the LAN PCs to this new
address to access Internet. Be sure to write the new address on a sticky label and attach it to the bottom of the unit. You
will need the new address to log in to the device in the future.
_________________________________________________________________________________________________
4.2.4 NAT
This section explains the following:
• Virtual Server
• Port Triggering
• DMZ Host
Virtual Server
The Virtual Server is useful for web servers, ftp servers, e-mail servers, gaming and other specialized Internet
applic ations. When you enable the Virtual Server, the communication requests from the Internet to your router’s WAN
port will be forwarded to the specified LAN IP address.
49
Page 54
Wireless Modem Router
To enter the virtual server screen, click NAT -> Virtual Server and then click the Add button to add rules.
Use Interface: Select a WAN connection to which you wish to apply the rules. When there is only one WAN connection
available, the rules will be automatically applied to it.
Service Name:
- Select a Service option: Allows you to select an existing service from the drop-down list.
- Custom Service: Allows you to customize a service.
Server IP Address: Enter the IP address of your local computer that will provide this service.
External Starting Port and External Ending Port: These are the starting number and ending number for the public
ports at the Internet interface.
Protocol: Select the protocol from the Protocol drop-down list. If you are unsure, select TCP/UDP.
Internal Starting Port and Internal Ending Port: These are the starting number and ending number for the ports of a
computer on the router’s local area network (LAN).
_________________________________________________________________________________________________
Note:
If you have enabled the UPnP functionality on both the router and your PC that is attached to one of the LAN port on the
router, you will be prompted on the Virtual Server page that the UPnP interface is being used.
_________________________________________________________________________________________________
Application Example:
You have set up two servers on your LAN side:
- An FTP server (using the default port number of 21) at the IP address of 192.168.1.100
- A web server (using the default port number of 80) at the IP address of 192.168.1.110
And want your friends on Internet to access the FTP server and web server on default ports. To access your FTP or web
50
Page 55
Wireless Modem Router
server from the Internet, a remote user has to know the Internet IP address or Internet name of your router, such as
www.tendacn.com. In this example, we assume the Internet IP address of your router is 183.37.227.201. Then follow
instructions below:
To configure the router to make your local FTP server public:
Click NAT -> Virtual Server to enter it and then click the Add button.
- Select FTP that you wish to host on your network from the Select a Service drop-down list. The port number (21) used
by this service will then be automatically populated.
- Or if you wish to define the service yourself, enter a descriptive name in the Custom Service, say My FTP, and then
manually enter the port number (21) used by this service in the Internal Starting Port, Internal Ending Port, External
Starting Port and External Ending Port fields.
Select a protocol from the Protocol drop-down list. If you are unsure, select TCP/UDP.
In the Server IP Address field, enter the last digit of the IP address of your local computer that offers this service. Here
in this example, we enter 192.168.1.100.
Click the Apply/Save button.
Your friends on Internet will then be able to access your FTP server simply by entering "ftp://183.37.227.201" in his
browser.
To configure your router to make your local web server public:
Click NAT -> Virtual Server to enter it and then click the Add button.
- Select Web Server (HTTP) that you wish to host on your network from the Select a Service drop-down list. The port
number (80) used by this service will then be automatically populated.
- Or if you wish to define the service yourself, enter a descriptive name in the Custom Service, say My Web Server
(HTTP), and then manually enter the port number (80) used by this service in the Internal Starting Port, Internal
Ending Port, External Starting Port and External Ending Port fields.
Select a protocol from the Protocol drop-down list. If you are unsure, select TCP/UDP.
In the Server IP Address field, enter the last digit of the IP address of your local computer that offers this service. Here
in this example, we enter 192.168.1.110.
Click the Apply/Save button.
51
Page 56
Wireless Modem Router
Now you can view your configurations as seen in the screenshot below. Your friends on Internet will then be able to
access the web server simply by entering "http://183.37.227.201" in his browser.
_________________________________________________________________________________________________
Note:
The "Internal Port End" cannot be modified directly. Normally, it is set to the same value as "External Port End".
However, if you modify "Internal Port Start", then "Internal Port End" will be set to the same value as "Internal Port
Start".
Tip:
If the service or game you wish to host on your network is not included in the list, manually add it in the Custom Service
field and then add the port number used by it to the Internal Starting Port, Internal Ending Port, External Starting
Port and External Ending Port fields.
_________________________________________________________________________________________________
Port Triggering
Some applications such as games, video conferencing, remote access applications and others require that specific ports in
the Router's firewall be opened for access by the applications. Port Trigger dynamically opens up the 'Open Ports' in the
firewall when an application on the LAN initiates a TCP/UDP connection to a remote party using the 'Triggering Ports'.
The Router allows the remote party from the WAN side to establish new connections back to the application on the LAN
side using the 'Open Ports'.
52
Page 57
Wireless Modem Router
To enter the Port Triggering screen, click NAT -> Port Triggering and then click the Add button to add rules.
You can configure the port settings from this screen by selecting an existing application or creating your own (Custom
application) and click "Save/Apply" to add it.
Use Interface: Select a WAN connection to which you wish to apply the rules. When there is only one WAN connection
available, the rules will be automatically applied to it.
Application Name: Two options are available:
- Select an application
- Custom application
Trigger Port Start/Trigger Port End: The port range for an application to initiate connections.
Trigger Protocol: Select the protocol from the drop-down list. If you are unsure, select TCP/UDP.
Open Port Start/ Open Port End: These are the starting number and ending number for the ports that will be
automatically opened by the built-in firewall when connections initiated by an application are established.
DMZ Host
The default DMZ (De-Militarized Zone) host feature is helpful when you are using some online games and
videoconferencing applications that are not compatible with NAT (Network Address Translation).
53
Page 58
Wireless Modem Router
DMZ Host IP Address: The IP Address of the device for which the router’s firewall w ill be disabled. Be sure to assign a
static IP Address to that device. The DMZ host should be connected to a LAN port of the device. Be sure to assign a
static IP address to that DMZ host.
_________________________________________________________________________________________________
Warning!
DMZ servers pose a security risk. A computer designated as the DMZ server loses much of the protection of the firewall
and is exposed to exploits from the Internet.
_________________________________________________________________________________________________
4.2.5 Security
This section explains the following information:
• IP Filtering
• MAC Filtering
IP Filtering
Outgoing IP Filtering Setup
By default, all outgoing IP traffic from LAN is allowed, but some IP traffic can be BLOCKED by setting up filters.
Choose Add or Remove to configure outgoing IP filters.
54
Page 59
Wireless Modem Router
Choose Add to enter the following screen:
This screen allows you to create a filter rule to identify outgoing IP traffic by specifying a new filter name and at least
one condition below. All of the specified conditions in this filter rule must be satisfied for the rule to take effect. Click
'Apply/Save' to save and activate the filter.
Filter Name: Enter a descriptive filtering name.
IP Version: Select either IPv4 or IPv6.
Protocol: TCP/UDP, TCP, UDP and ICMP are available for your option.
Source IP address [/prefix length]: Enter the LAN IP address to be filtered.
Source Port (port or port: port): Specify a port number or a range of ports used by LAN PCs to access Internet. If you
are unsure, leave it blank.
Destination IP address [/prefix length]: Specify the external network IP address to be accessed by specified LAN PCs.
Destination Port (port or port:port): Specify a port number or a range of ports used by LAN PCs to access external
network.
Incoming IP Filtering Setup
When the firewall is enabled on a WAN or LAN interface, all incoming IP traffic is BLOCKED. However, some IP
traffic can be ACCEPTED by setting up filters.
Choose Add or Remove to configure incoming IP filters.
55
Page 60
Wireless Modem Router
Click Add to enter the following screen:
This screen allows you to create a filter rule to identify incoming IP traffic by specifying a new filter name and at least
one condition below. All of the specified conditions in this filter rule must be satisfied for the rule to take effect. Click
Apply/Save to save and activate the filter.
IP Version: Select either IPv4 or IPv6.
Protocol: TCP/UDP, TCP, UDP and ICMP are available for your option.
Source IP address [/prefix length]: Enter the Internal IP address [/prefix length] to be filtered.
Source Port (port or port: port): Specify a port number or a range of ports used by PCs from external network to
access your internal network.
Destination IP address [/prefix length]: Specify the internal network IP address [/prefix length] to be accessed by the
specified PCs from external network.
Destination Port (port or port:port): Specify a port number or a range of ports used by PCs from external network to
access your internal network.
MAC Filtering
A bridge WAN service is needed to configure this service.
MAC Filtering is only effective on ATM PVCs configured in Bridge mode. FORWARDED means that all MAC layer
frames will be FORWARDED except those matching with any of the specified rules in the following table. BLOCKED
means that all MAC layer frames will be BLOCKED except those matching with any of the specified rules in the
following table.
Choose Add or Remove to configure MAC filtering rules.
56
Page 61
Wireless Modem Router
_________________________________________________________________________________________________
Warning!
Changing from one policy to another of an interface will cause all defined rules for that interface to be REMOVED
AUTOMATICALLY! You will need to create new rules for the new policy.
_________________________________________________________________________________________________
Click Add to enter the following screen:
Here you can create a filter to identify the MAC layer frames by specifying at least one condition below. If multiple
conditions are specified, all of them take effect. Click Save/Apply to save and activate the filter.
Protocol Type: Select a protocol type from the drop-down list.
Destination MAC Address: Enter the destination MAC address apply the MAC filtering rule to which you wish to
apply the MAC filtering rule.
Source MAC Address: Enter the source MAC address to which you wish to apply the MAC filtering rule.
Frame Direction: Select a frame direction from the drop-down list.
WAN Interfaces: Select a WAN interface from the drop-down list.
4.2.6 Parental Control
This section explains the following information:
• Time Restriction
• URL Filter
Time Restriction
Click Parental Control -> Time Restriction -> Add to enter the following screen.
57
Page 62
Wireless Modem Router
Here you can add time of day restriction that an attached LAN device can access the Internet.
The Browser's MAC Address' automatically displays the MAC address of the LAN device where the browser is running.
To restrict other LAN device, click the "Other MAC Address" button and enter the MAC address of the other LAN
device.
User Name: Enter a user name.
Browser's MAC Address: Automatically adds the MAC address of the attached LAN device where the browser is
running.
Other MAC Address: Specify the MAC address of the computer that you want to apply Internet access restriction.
Days of the week: Click to select the days of the week during which you wish to restrict Internet access.
Start Blocking Time/ End Blocking Time: Specify time of day restriction to an attached LAN device. Within this
specified time length of the day, this LAN device will be blocked from Internet.
Apply/Save: Click to Apply/Save your settings.
URL Filter
Here you can add URL access restriction to specific LAN PCs.
Select the URL List Type (Exclude or Include) first and then click Add to enter the screen below for configuring the list
entries. Maximum 100 entries can be configured.
58
Page 63
Wireless Modem Router
URL Address: Enter the URLs that a specific LAN PC cannot access.
Port Number: Specify the port number used by the web server. The default is 80, which is the standard protocol for web
servers.
Enter the URL address and port number then click "Apply/Save" to add the entry to the URL filter.
_________________________________________________________________________________________________
Note:
If you have accessed the URL before you include it in a URL filter rule, you must reboot the router and erase it from your
PC to activate this URL filter rule. To erase the domain name from your PC, click Start -> Run, enter cmd and then type
ipconfig /flushdns.
_________________________________________________________________________________________________
4.2.7 Quality of Service
This section explains the following:
• QoS Queue
• QoS Classification
If Enable QoS checkbox is selected, choose a default DSCP mark to automatically mark incoming traffic without
reference to a particular classifier. Click Apply/Save button to save it.
59
Page 64
Wireless Modem Router
Enable QoS: Check/uncheck to enable/disable the QoS feature.
_________________________________________________________________________________________________
Note:
1. If Enable Qos checkbox is not selected, all QoS will be disabled for all interfaces.
2. The default DSCP mark is used to mark all egress packets that do not match any classification rules.
_________________________________________________________________________________________________
QoS Queue
In ATM mode, maximum 8 queues can be configured.
In PTM mode, maximum 8 queues can be configured.
For each Ethernet interface, maximum 4 queues can be configured.
For each Ethernet WAN interface, maximum 4 queues can be configured.
To add a queue, click the Add button.
To remove queues, check their remove-checkboxes, then click the Remove button.
The Enable button will scan through every queues in the table. Queues with enable-checkbox checked will be enabled.
Queues with enable-checkbox un-checked will be disabled.
The enable-checkbox also shows status of the queue after page reload.
Note that if WMM function is disabled in Wireless Page, queues related to wireless will not take effects.
60
Page 65
Wireless Modem Router
To add a queue, click the Add button to enter the following screen.
Here you can configure a QoS queue and add it to a selected layer2 interface.
QoS Classification
To add a rule, click the Add button.
To remove rules, check their remove-checkboxes, then click the Remove button.
The Enable button will scan through every rule in the table. Rules with enable-checkbox checked will be enabled. Rules
with enable-checkbox un-checked will be disabled.
The enable-checkbox also shows status of the rule after page reload.
If you disable WMM function in Wireless Page, classification related to wireless will not take effects.
61
Page 66
Wireless Modem Router
To add a rule, click the Add button to enter the following screen.
Here you can create a traffic class rule to classify the ingress traffic into a priority queue and optionally mark the DSCP
or Ethernet priority of the packet.
Click Apply/Save to save and activate the rule.
4.2.8 Routing
This section explains the following:
• Default Gateway
• Static Route
Default Gateway
Default gateway interface list can have multiple WAN interfaces served as system default gateways but only one will be
used according to the priority with the first being the highest and the last one the lowest priority if the WAN interface is
62
Page 67
Wireless Modem Router
connected. Priority order can be changed by removing all and adding them back in again.
Selected Default Gateway Interfaces: Displays the selected default gateway interfaces. Select a WAN interface and
click the button to move it to the Available Routed WAN Interfaces box.
Available Routed WAN Interfaces: Displays the available routed WAN interfaces. Select a WAN interface and click the
button to add it to the Selected Default Gateway Interfaces box.
Apply/Save: Click to save and activate your settings.
Static Route
Static routes provide additional routing information to your router. Typically, you do not need to add static routes.
However, when there are several routers in the network, you may want to set up static routing. Static routing determines
the path of the data in your network. You can use this feature to allow users on different IP domains to access the Internet
via this device. It is not recommended to use this setting unless you are familiar with static routing. In most cases,
dynamic routing is recommended, because this feature allows the router to detect the physical changes of the network
layout automatically. If you want to use static routing, make sure the router’s DHCP function is disabled.
Click Add to enter the following screen:
63
Page 68
Wireless Modem Router
IP Version: Select either IPv4 or IPv6.
Destination IP address/prefix length: Enter the destination IP address and prefix length of the final destination.
Interface: Select an interface from the drop-down list.
Gateway IP address: Enter the gateway IP address, which must be a router on the same LAN segment as the router.
Metric: Enter a number in the Metric field. This stands for the number of routers between your network and the
destination.
Apply /Save: Click to apply and save your settings.
_________________________________________________________________________________________________
Note:
1. Destination IP address cannot be on the same IP segment as WAN or LAN segment as the router.
2. Only configure additional static routes for unusual cases such as multiple routers or multiple IP subnets located on
your network. Wrong static routes may lead to network failure.
3. For system created route, the 'Remove' checkbox is disabled.
_________________________________________________________________________________________________
4.2.9 DNS
DNS Server (Static DNS)
The DNS server translates domain names to numeric IP addresses. It is used to look up site addresses based on their
names.
Select DNS Server Interface from available WAN interfaces OR enter static DNS server IP addresses for the system.
Here you can configure the WAN DNS address:
For IPv4:
-Click the Select DNS Server Interface from available WAN interfaces option
-OR select the Use the following Static DNS IP address option and enter static DNS server IP addresses for the system
And then click Apply/Save.
64
Page 69
Wireless Modem Router
For IPv6:
-Select Obtain IPv6 DNS info from a WAN interface and Select a configured WAN interface for the IPv6 DNS server
information.
-Select Use the following Static IPv6 DNS address and enter the static IPv6 DNS server Addresses.
And then click Apply/Save.
_________________________________________________________________________________________________
Note:
1. DNS Server Interfaces can have multiple WAN interfaces served as system DNS servers but only one will be used
according to the priority with the first being the highest and the last one the lowest priority if the WAN interface is
connected. Priority order can be changed by removing all and adding them back in again.
2. In ATM mode, if only a single PVC with IPoA or static IPoE protocol is configured, Static DNS server IP addresses
must be entered.
3. If you cannot locate the static DNS server IP information, ask your ISP to provide it.
4. The default settings are recommended if you are unsure about the DNS server addresses. If a wrong DNS server
address is configured, webpages may not be open.
_________________________________________________________________________________________________
Dynamic DNS (DDNS)
If your Internet service provider (ISP) gave you a static (fixed) public IP address, you can register a domain name and
have that name associated with your IP address by public Domain Name Servers (DNS). However, if your ISP gave you
a dynamic (changing) public IP address, you cannot predict what your IP address will be, and the address can change
frequently. In this case, you can use a commercial Dynamic DNS service. It lets you register your domain to their IP
address and forwards traffic directed at your domain to your frequently changing IP address. If your ISP assigns a private
WAN IP address (such as 192.168.x.x or 10.x.x.x), the Dynamic DNS service does not work because private addresses
are not routed on the Internet.
Click Advanced Setup -> DNS -> Dynamic DNS to enter the Dynamic DNS screen.
65
Page 70
Wireless Modem Router
Click the Add button to configure the DDNS settings.
D-DNS Provider: Select your DDNS service provider from the drop-down menu.
Hostname: Enter the DDNS domain name registered with your DDNS service provider.
Interface: Specify a WAN connection interface.
Username: Enter the DDNS user name registered with your DDNS service provider.
Password: Enter the DDNS Password registered with your DDNS service provider.
Click Apply/Save to save your settings.
Example: NO-IP
Hostname: xhh3793.zapto.org
Username: qiangweianbian
Password: 414637
Add Dynamic DNS
1 Select NO-IP from the D-DNS provider drop-down menu.
2 Enter your NO-IP hostname. Here is “xhh3793.zapto.org” for example.
3 Specify a WAN connection interface.
66
Page 71
Wireless Modem Router
NO-IP Settings
1 Enter your NO-IP username. Here is “qiangweianbian” for example.
2 Enter the password of your NO-IP account. Here is “414637” for example.
3 Click Apply/Save to save your configuration.
67
Page 72
Wireless Modem Router
4.2.10 DSL
This screen provides multiple ASDL modulation modes to meet diversified environments. You can also select phone line
pair and Capability.
DSL parameter configurations must be supported by ISP to take effect. Actual parameters (see Statistics-xDSL) resulted
from the negotiation between your router and ISP. Wrong configurations may fail your Internet access.
The best DSL configurations are the factory defaults. Only change them if you are instructed by your ISP or our
technical staff when your router fails to negotiate with ISP in DSL (ATM) mode. Usually, this failure can be identified
and confirmed if the ADSL LED on the device keeps displaying a slow or quick blinking light.
Check the checkbox next to a modulation to enable it and then click Apply/Save.
Advanced Settings: Click it to enter the Advanced Settings screen as below.
68
Page 73
Wireless Modem Router
Here you can select the test mode and tone.
_________________________________________________________________________________________________
Tip:
If you are unsure about the ADSL parameters, please apply the factory default settings. Wrong configurations may fail
your Internet access.
_________________________________________________________________________________________________
4.2.11 UPnP
UPnP (Universal Plug and Play) allows Windows based systems to configure the device for various Internet applications
automatically. UPnP devices can automatically discover the services from other registered UPnP devices on the network.
If you use applications such as multiplayer gaming, peer-to-peer connections, or real-time communications, like instant
messaging or remote assistance (a feature in Windows XP), you should enable UPnP.
Enable UPnP: Check/uncheck to enable/disable the UPnP feature.
69
Page 74
Wireless Modem Router
_________________________________________________________________________________________________
Note:
UPnP is activated only when there is a live WAN service with NAT enabled.
_________________________________________________________________________________________________
4.2.12 Print Server (Available only in D301)
This page allows you to enable / disable printer support.
Enable on-board print server: Check/uncheck to enable / disable the printer support.
Printer name: Enter a descriptive name of your printer.
Make and model: Enter the make and model of your printer.
Apply/Save: Click to apply and save your settings.
4.2.13 Storage Service (Available only in D301)
The Storage service allows you to use Storage devices with the modem router to be more easily accessed.
This section explains the following:
• Storage Device Info
• User Account
Storage Device Info
This screen displays the information of the storage device as seen on the screenshot below.
70
Page 75
User Account
Wireless Modem Router
This section allows you to Add, or Remove User Accounts.
To add a user account:
Click Add to enter the following screen:
71
Page 76
Wireless Modem Router
Enter the user name, password and volume name on which the home directory is to be created.
Click Apply/Save to apply and save your settings.
To remove an existing user account:
Check Remove next to the user account.
Click the Remove button.
4.2.14 Interface Grouping
Interface Grouping supports multiple ports to PVC and bridging groups. Each group will perform as an independent
network. To support this feature, you must create mapping groups with appropriate LAN and WAN interfaces using the
Add button. The Remove button will remove the grouping and add the ungrouped interfaces to the Default group. Only
the default group has IP interface.
Click Add to enter the screen below:
72
Page 77
Wireless Modem Router
Group Name: The name of a configured rule.
WAN Interface used in the grouping: WAN connection to which the interface grouping rules apply.
Available LAN Interfaces: LAN interfaces that can be used for interface grouping.
Grouped LAN Interfaces: LAN interfaces that use specified WAN interface.
To create a new interface group:
Enter the Group name and the group name must be unique and select either 2. (dynamic) or 3. (static) below:
If you like to automatically add LAN clients to a WAN Interface in the new group add the DHCP vendor ID string. By
configuring a DHCP vendor ID string any DHCP client request with the specified vendor ID (DHCP option 60) will be
denied an IP address from the local DHCP server.
Select interfaces from the available interface list and add it to the grouped interface list using the arrow buttons to create
the required mapping of the ports. Note that these clients may obtain public IP addresses.
Click Apply/Save button to make the changes effective immediately.
_________________________________________________________________________________________________
Note:
If a vendor ID is configured for a specific client device, please REBOOT the client device attached to the modem to
allow it to obtain an appropriate IP address.
_________________________________________________________________________________________________
4.2.15 IP Tunnel
This section explains the following information:
• IPv6inIPv4
• IPv4inIPv6
IPv6inIPv4
Click IPv6inIPv4 and Add to enter the following screen:
73
Page 78
Wireless Modem Router
Tunnel Name: Specify the name of the tunnel.
Mechanism: Currently, only DS-Lite configuration is supported.
Associated WAN Interface: Specify the WAN interface of the tunnel.
Associated LAN Interface: Specify the LAN interface of the tunnel.
Manual: If you select Manual, configure the following settings also:
IPv4 Mask Length: Specify the IPv4 Mask Length.
6rd Prefix with Prefix Length: Specify the 6rd Prefix with Prefix Length.
Border Relay IPv4 Address: Specify the Border Relay IPv4 Address.
Automatic: If Automatic is selected, no configurations are required.
Apply/Save: Click to apply and save your settings.
IPv4inIPv6
Click IPv4inIPv6 and Add to enter the following screen:
74
Page 79
Wireless Modem Router
Tunnel Name: Specify the name of the tunnel.
Mechanism: Currently, only 6rd configuration is supported.
Associated WAN Interface: Specify the WAN interface of the tunnel.
Associated LAN Interface: Specify the LAN interface of the tunnel.
Manual: If you select Manual, enter the AFTR information also:
Automatic: If Automatic is selected, no configurations are required.
Apply/Save: Click to apply and save your settings.
4.2.16 Certificate
This section explains the following information:
• Local Certificates
• Trusted CA (Certificate Authority) Certificates
Local Certificates
Here you can Add, View or Remove certificates. Local certificates are used by peers to verify your identity. Maximum 4
certificates can be stored.
To generate generate a certificate signing request:
Click the Create Certificate Request button to enter the page below.
75
Page 80
Wireless Modem Router
Specify the Common Name, Organization Name and State/Province Name
Enter the 2-letter Country Code for the certificate.
Click Apply to apply your settings.
To Import certificate：
Click the Import Certificate button on the local certificates page to enter the page below.
76
Page 81
Wireless Modem Router
Enter the certificate name.
Paste the certificate content and private key.
Click Apply to apply your settings.
Trusted CA (Certificate Authority) Certificates
Here you can Add, View or Remove CA certificates. CA certificates are used by you to verify peers' certificates.
Maximum 4 certificates can be stored.
To Import certificate：
Click the Import Certificate button to enter the page below.
77
Page 82
Wireless Modem Router
Enter the certificate name.
Paste the certificate content.
Click Apply to apply your settings.
4.2.17 Multicast
Here you can configure the multicast feature.
To configure IGMP for IPv4
Check the LAN to LAN (Intra LAN) Multicast Enable box.
Check the Membership Join Immediate (IPTV) box. This is only required for IPTV.
Keep other options unchanged from factory defaults if you are not an advanced user. This is strongly recommended.
To configure IGMP for IPv6
Check the LAN to LAN (Intra LAN) Multicast Enable box.
Keep other options unchanged from factory defaults if you are not an advanced user. This is strongly recommended.
78
Page 83
Wireless Modem Router
4.2.18 IPTV
If you check the Enable IPTV checkbox, you must choose a layer2 interface, and then configure the PVC/VLAN info
(ATM), or ETH port/VLAN info (ETH). Click Apply/Save button to save it.
Enable IPTV: Check/uncheck to enable/disable the IPTV service.
79
Page 84
Wireless Modem Router
_________________________________________________________________________________________________
Tip:
For tagged service, enter valid 802.1P Priority and 802.1Q VLAN ID.
For untagged service, set -1 to both 802.1P Priority and 802.1Q VLAN ID.
_________________________________________________________________________________________________
4.3 Wireless
This section explains the following information:
• Basic
• Security
• MAC Filter
• Wireless Bridge
• Station Info
4.3.1 Basic
This page allows you to configure basic features of the wireless LAN interface. You can enable or disable the wireless
LAN interface, hide the network from active scans, set the wireless network name (also known as SSID) and restrict the
channel set based on country requirements.
Click Apply/Save to configure the basic wireless options.
Enable Wireless: check/uncheck to enable/disable the wireless feature.
SSID: This is thepublic name of your wireless network.
Hide SSID (Hide Access Point): This option allows you to have your network names (SSID) publicly broadcast or if
you choose to enable it, the SSID will be hidden.
BSSID: Display the BSSID.
Country: Select your country.
Max Clients: The max wireless clients your wireless network can accept. Up to 8 clients can join your wireless network
at a time. The default setting is 8.
Channel: Select a channel or select Auto to let system automatically select one for your wireless network to operate on
if you are unsure. The best selection is a channel that is the least used by neighboring networks.
80
Page 85
Wireless Modem Router
4.3.2 Security
This page allows you to configure security features of the wireless LAN interface. You may setup configuration
manually OR through WiFi Protected Setup (WPS).
WPS Setup
Wi-Fi Protected Setup makes it easy for home users who know little of wireless security to establish a home network, as
well as to add new devices to an existing network without entering long passphrases or configuring complicated settings.
Simply enter a PIN code on the device web interface or press hardware WPS button (on the back panel of the device) and
a secure wireless connection is established.
WPS Button: Press the hardware WPS button on the device for 1 second and the WPS LED will keep blinking for about
2 minutes. Within the 2 minutes, press the WPS button on your wireless computer or other device. When the WPS
displays a solid light, the device has joined your wireless network.
PIN: To use this option, you must know the PIN code from the wireless client and enter it in the corresponding field on
your device while using the same PIN code on client side for such connection.
Enable WPS: Check/uncheck to enable/disable the WPS function. It is enabled by default.
_________________________________________________________________________________________________
Note:
1. To use the WPS security, the wireless client must be also WPS-capable.
2. When both STA PIN and Authorized MAC are empty, PBC is used. If Hide Access Point enabled or Mac filter list is
empty with "allow" chosen, WPS2 will be disabled.
_________________________________________________________________________________________________
Manual Setup AP
You can set the network authentication method, selecting data encryption, specify whether a network key is required to
authenticate to this wireless network and specify the encryption strength.
Click "Apply/Save" when done.
81
Page 86
Wireless Modem Router
Network Authentication: Select Open, Shared, WPA-PSK, WPA2-PSK or Mixed WPA/ WPA2-PSK from the
drop-down list to encrypt your wireless network.
Depending on the type of network authentication you select, you will be prompted to enter corresponding settings.
WEP Encryption: Select Enabled or Disabled.
Encryption Strength: Select 128-bit or 64-bit.
Current Network Key: Select a network key to be active.
Network Key 1/2/3/4: Enter 13 ASCII characters or 26 hexadecimal digits for 128-bit encryption keys; enter 5 ASCII
characters or 10 hexadecimal digits for 64-bit encryption keys.
WPA/WAPI passphrase: Enter a WPA/WAPI network key.
WPA Group Rekey Interval: Specify a key update interval.
WPA/WAPI Encryption: Select AES or TKIP+AES.
4.3.3 MAC Filter
The MAC-based Wireless Access Control feature can be used to allow or disallow clients to connect to your wireless
network.
Allow: Only allow PCs at specified MAC addresses (in the list) to connect to your wireless network.
Deny: Block only PCs at specified MAC addresses from connecting to your wireless network.
Disable: Disable this feature.
Add: Click to add a MAC address.
To delete an existing MAC address, first check the Remove box next to the MAC address in list and then click the
Remove button.
Example 1: To allow only the PC at the MAC address of 00:1A:3D:9C:BB:23 to connect to your wireless network, do as
follows:
Select Allow.
Click the Add button.
Enter 00:1A:3D:9C:BB:23 in the MAC address box as shown in the figure below:
82
Page 87
Wireless Modem Router
Click Apply/Save.
_________________________________________________________________________________________________
Note:
If “allow” is choosed and mac filter is empty, WPS will be disabled.
_________________________________________________________________________________________________
4.3.4 Wireless Bridge
This page allows you to configure wireless bridge (also known as Wireless Distribution System) features of the wireless
LAN interface.
Wireless distribution system (WDS) is a system enabling the wireless interconnection of access points in an IEEE 802.11
network. It allows a wireless network to be expanded using multiple access points without the traditional requirement for
a wired backbone to link them.
AP Mode: You can select Wireless Bridge (also known as Wireless Distribution System) to disable access point
functionality. Selecting Access Point enables access point functionality. Wireless bridge functionality will still be
83
Page 88
Wireless Modem Router
available and wireless stations will be able to associate to the AP.
Bridge Restrict: There are three options available: Enabled, Enabled (Scan) and Disabled. Select Disabled in Bridge
Restrict which disables wireless bridge restriction. Any wireless bridge will be granted access. Selecting Enabled or
Enabled (Scan) enables wireless bridge restriction. Only those bridges selected in Remote Bridges will be granted access.
The Enabled (Scan) enables wireless bridge restriction and automatically scans the remote bridges.Remote Bridges
MAC Address: Specify the MAC address of the remote bridge. If you select the Enabled (Scan) option in Bridge
Restrict, system automatically scans the remote bridges and you only need to select those bridges and their MAC
addresses will be added to automatically.
Refresh: Click to update the remote bridges. Wait for few seconds to update.
Apply/Save: Click to apply and save the settings.
_________________________________________________________________________________________________
Note:
The WDS feature (also known as Wireless Bridge) can only be implemented between 2 WDS-capable wireless devices.
Plus, SSID, channel, security settings and security key must be exactly the same on both such devices.
_________________________________________________________________________________________________
4.3.5 Station Info
This page shows authenticated wireless stations and their status.
4.4 Diagnostics
The modem router is capable of testing the connection to your DSL service provider, the connection to your Internet
service provider and the connection to your local network. If a test displays a fail status, click "Rerun Diagnostic Tests"
at the bottom of this page to make sure the fail status is consistent. If the test continues to fail, click "Help" and follow
the troubleshooting procedures.
84
Page 89
Wireless Modem Router
4.5 Management
This section explains the following information:
• Settings
• System Logs
• Security Log
• SNMP Agent
• TR-069 Client
• Internet Time
• Access Control
• Update Software
• Reboot
4.5.1 Settings
This section explains the following information:
• Backup
• Update
• Restore Default
Backup
Here you can save a copy of your device’s c onfigurations to your computer. Once you have configured the device, you
can save these settings to a configuration file on your local hard drive. The configuration file can later be imported to
your device in case the device is reset to factory default settings.
Update
Here you can restore the configuration from a file saved on your PC.
85
Page 90
Wireless Modem Router
Restore Default
Under some circumstances (for example, join a different network or unfortunately forgetting the login password), you
may need to remove the existing configuration and restore the factory default settings.
4.5.2 System Logs
The System Log dialog allows you to view the System Log and configure the System Log options.
86
Page 91
Wireless Modem Router
To view the System Log, simply click View System Log.
To configure the System Log options, click Configure System Log.
Log: If Enable is selected, the system will begin to log all the selected events.
Log Level: All events above or equal to the selected level will be logged.
Display Level: All logged events above or equal to the selected level will be displayed.
Mode: If the selected mode is 'Remote' or 'Both,' events will be sent to the specified IP address and UDP port of the
remote syslog server. If the selected mode is 'Local' or 'Both,' events will be recorded in the local memory.
Server IP Address: Specify the IP address of the remote syslog server.
Server UDP Port: Specify the UDP port of the remote syslog server.
Apply/Save: click to apply and save the system log settings.
4.5.3 Security Log
The Security Log page allows you to view the Security Log and configure the Security Log options. You can also save
Security Log to a file.
87
Page 92
Wireless Modem Router
View: Click to view the Security Log.
Reset: Click to clear and reset the Security Log.
4.5.4 SNMP Agent
Simple Network Management Protocol (SNMP) allows a management application to retrieve statistics and status from
the SNMP agent in this device.
SNMP Agent：Selec t “Enable” to activate the SNMP Agent feature or “Disable” to deactivate it.
Read Community: Specify a Read Community string. The default is public.
Set Community: Specify a Set Community string. The default is private.
System Name: Specify a descriptive system name.
System Location: Specify a system location.
System Contact: Specify a system contact.
Trap Manager IP: Specify the IP address of the Trap Manager.
4.5.5 TR-069 Client
WAN Management Protocol (TR-069) allows an Auto-Configuration Server (ACS) to perform auto-configuration,
provision, collection, and diagnostics to this device.
Click the TR-069 Client tab to enter the TR-069 Client configuration screen as seen below:
88
Page 93
Wireless Modem Router
Inform: Select Enable/Disable to enable/disable the TR-069 Client function. By default, it is disabled.
Inform Interval: Specify the inform interval.
ACS URL: Enter the ACS (Auto-Configuration Server) URL address.
ACS User Name: Enter the ACS (Auto-Configuration Server) user name.
ACS Password: Enter the ACS (Auto-Configuration Server) password.
WAN Interface used by TR-069 client: Select the WAN interface used by the TR-069 client from the drop-down list.
Display SOAP messages on serial console: If Enable is selected, SOAP messages will be displayed on serial console; if Disable is
selected, SOAP messages will not be displayed on serial console.
Connection Request Authentication: Check/uncheck to enable/disable the connection request authentication.
Connection Request User Name: Enter the connection request user name.
Connection Request Password: Enter the connection request password.
Connection Request URL: Specify the connection request URL.
4.5.6 Internet Time
This page is used to set the router’s system time. If Automatically synchronize with Internet time servers is checked,
the system will automatically connect to NTP server to synchronize the time.
First/Second/Third/Fourth/Fifth NTP time server: Select a NTP time server from the drop-down list. If the NTP time
server you are looking for is not included in the list, select “Other” and then enter it manually in the box.
Time zone offset: Select your time zone from the drop-down list.
4.5.7 Access Control
This section explains the following information:
• Password
• AccessControl - Service
Password
Access to your broadband router is controlled through three user accounts: admin, support, and user.
89
Page 94
Wireless Modem Router
The user name "admin" has unrestricted access to change and view configuration of your Broadband Router.
The user name "support" is used to allow an ISP technician to access your Broadband Router for maintenance and to run
diagnostics.
The user name "user" can access the Broadband Router, view configuration settings and statistics, as w ell as, update the
router's software.
User Name: Enter the user name of up to 16 characters.
Old Password: Enter the old password of up to 16 characters.
New Password: Enter a new password of up to 16 characters.
Confirm Password: Re-enter to confirm the new password.
Apply/Save: Click to change or create passwords.
_________________________________________________________________________________________________
Note:
Password cannot contain a space.
_________________________________________________________________________________________________
Access Control - Service
Here you can manage the device either from LAN or WAN side using HTTP, ICMP, TELNET, SNMP and FTP.
90
Page 95
Wireless Modem Router
_________________________________________________________________________________________________
Note:
1. If you are not an advanced user, we suggest you keep the default settings.
2. To access the device from the LAN side, you must use the LAN IP address and log in as "admin" or "user"; to access
the device from the WAN side, you must use the WAN IP address and log in as "support".
_________________________________________________________________________________________________
4.5.8 Update Software
Firmware upgrade is released periodically to improve the functionality of your device and add any new features. If you
run into a problem with a specific feature of the device you could log in to our website (www.tendacn.com) to download
the latest firmware to update your device.
91
Page 96
Wireless Modem Router
To update software, do as follows:
Obtain an updated software image file from our website: www.tendacn.com.
Enter the path to the image file location in the box below or click the "Browse" button to locate the image file.
Click the "Update Software" button once to upload the new image file.
_________________________________________________________________________________________________
Note:
The update process takes about 2 minutes to complete, and your Broadband Router will reboot.
_________________________________________________________________________________________________
4.5.9 Reboot
Click the Reboot button to reboot the router.
92
Page 97
Wireless Modem Router
Appendix 1 Configure Your PC
Screens to configure TCP/IP properties in other Operating Systems are similar to those below.
Windows 7
Click Start-> Control Panel-> Network and Sharing Center-> Change adapter settings, select a desired Local Area
Connection and select Properties.
93
Page 98
Wireless Modem Router
94
Page 99
Wireless Modem Router
MAC
Click on the Apple icon from the top-left corner and select System Preferences.
95
Page 100
Wireless Modem Router
96
Loading...