Page 1
Page 2
Copyright Statement
is the registered trademark of Shenzhen
Tenda Technology Co., Ltd. Other trademark or trade
name mentioned herein are the trademark or registered
trademark of the company. Copyright of the whole
product as integration, including its accessories and
software, belongs to Shenzhen Tenda Technology Co.,
Ltd. Without the permission of Shenzhen Tenda
Technology Co., Ltd, individual or party is not allowed to
copy, plagiarize, imitate or translate it into other
languages.
All
the photos and product specifications mentioned in
this manual are for references only, as the upgrading of
software and hardware, there will be changes. And if
there are changes, Tenda is not responsible for
informing in advance. If you want to know more about
our products information, please visit our website at
www.tenda.cn
Page 3
D840R ADSL2+ Router User Guide
CONTENTS
Chapter 1 Overview ....................................................1
1.1 Product Introduction ....................................................1
1.2 Product Features ........................................................... 1
1.3 Supporting Protocol .....................................................1
1.4 Data Encapsulation ....................................................... 3
Chapter 2 Hardware Installation..................................4
2.1 ADSL Router Conne
2.2 USB Installation..................................................4
Chapter 3 Before Web Management Configuration ......5
3.1 Network Configuration of Your Computer.......... 5
3.2 Verifying the
3.3 Logging in to the Router .................................... 9
Chapter 4 Quick Installation Guide............................10
4.1 Configure the PPPoE
ction....................................4
Connection ................................... 8
........................................11
Page 4
D840R ADSL2+ Router User Guide
4.2 Configure the PPPoA ........................................ 13
4.3 Configure the MER ........................................... 15
4.4 Configure the IPoA........................................... 18
Chapter 5 Configurati
5.1Device Information
5.2Advanced Settings ............................................ 23
5.2.1 WAN
5.2.2 LAN
5.2.3 NAT
5.2.4 Security
5.2.5 Routing
5.2.6 DNS
5.2.7 DSL
5.3 DHCP ...............................................................73
5.4 System Tool..................................................... 73
5.4.1 Settings
5.4.2 System Log
5.4.3 Internet Time
5.4.4 Access Control
...........................................................49
...........................................................72
on Description.........................20
...........................................20
..........................................................23
..........................................................51
.....................................................57
.....................................................65
..........................................................67
....................................................74
...............................................76
............................................78
..........................................79
Page 5
D840R ADSL2+ Router User Guide
5.4.5 Software Update.................................................. 82
5.4.6 Save/Reboot ......................................................... 82
Chapter 6 Appendix .................................................83
Appendix 1: Troubleshooting .................................... 83
Appendix 2: FAQ ............................................................ 85
Page 6
D840R ADSL2+ Router User Guide
Chapter 1 Overview
1.1 Product Introduction
D840R ADSL2+ Router complies with ADSL, ADSL2 and
ADSL2+ standards. Supporting up to 24Mbps
downstream rate and 1Mbps upstream rate, it supports
multiple network protocols and provides NAT Router,
Bridge and switch functions. Built-in 4-port switch can
add more end users without purchasing hub or switch.
In addition, the intelligent software, Setup Wizard, can
assist you to access the Internet fast and easily. Powerful
and exquisite, it is the best choice for SOHO and small
enterprise users to share the Internet.
1.2 Product Features
Provides up to 24Mbps downstream rate and
1Mbps upstream rate
Supports DHCP, NAT, IGMP, ICMP, ARP
Four 10/100M Auto-Negotiation RJ-45 Ethernet
ports for network adapter, Hub and switch
1
Page 7
D840R ADSL2+ Router User Guide
connectivity
One RJ-11 port and Voice Splitter included
One USB port support for connecting PC’s USB port
Provides Web-based management and firmware
upgrade
Complies with ADSL, ADSL2 and ADSL2+ standards
Provides NAT Router, Bridge and switch functions
Compatible with all mainstream DSLAM (CO)
Provides PPPOE, PPPOA, CLIP protocols
Supports firewall and hacker attack prevention
Supports Internet Multi Media
Provides static and dynamic routes
Up to 6.5km transmission distance
Setup Wizard support for fast and easy
configurations
1.3 Supporting Protocol
Supports full-rate ADSL2+ standard
ANSI T1. 413 Issue 2
ITU-T G. 992. 1 (G. dmt)
ITU-T G. 992. 2 (G. Lite)
2
Page 8
D840R ADSL2+ Router User Guide
ITU-T G. 992. 3
ITU-T G. 992. 5
1.4 Data Encapsulation
Supports RFC 1483 Bridge、RFC 1483 Router
Supports Classical IP over ATM (RFC 1577)
Supports PPP over ATM(RFC 2364)
Supports PPP over Ethernet (RFC 2516)
3
Page 9
D840R ADSL2+ Router User Guide
Chapter 2 Hardware Installation
2.1 ADSL Router Connection
1. Connect one end of the telephone line to the LINE
port of the D810R and the other end to the
MODEM port of the voice splitter.
2. Connect the power adapter to the PWR port of the
D810R.
3. Use an Ethernet cable to connect the LAN port
with the NIC of your computer.
2.2 USB Installation
To connect the device to the USB interface of the
computer, please follow the steps below:
1. Connect to the USB port of the D810R through a
USB cable.
2. Connect the other end of the cable to the
computer’s USB port.
3. Set up the USB driver provided by the CD-ROM.
4
Page 10
D840R ADSL2+ Router User Guide
Chapter 3 Before Web Management
Configuration
3.1 Network Configuration of Your Computer
1．On the desktop of your
computer, right-click
“My Network Places”,
and then select
“Properties” in the
shortcut menu.
2. In the window that
appears, right-click
“Local Area
Connection”, and then
select "Properties”.
5
Page 11
D840R ADSL2+ Router User Guide
3．In the pop-up dialog
box, check “Internet
Protocol (TCP/IP)” and
then click “Properties”.
4. In the window that
appears, select “Obtain
an IP address
automatically (O)” or
“Use the following IP
address (S)”.
1) When “Obtain an IP
address automatically
(O)” is selected, the
window is as shown in
the right figure.
6
Page 12
D840R ADSL2+ Router User Guide
2) “Use the following IP
address”:
IP address:
192.168.1.XXX
(XXX ranges 2 ~ 254)
Subnet mask:
255.255.255.0
Default gateway:
192.168.1.1
DNS server: Enter the
local DNS server address
(for this address, you can
consult your ISP) or the
router’s default gateway
as the DNS server.
At the end of the setting,
click “OK” to submit the
settings. And then click
“OK” in the “Local Area
Connection Properties”
window.
7
Page 13
D840R ADSL2+ Router User Guide
3.2 Verifying the Connection
1． Select “Start→Programs
→Accessories→Comma
nd Prompt”.
According to the
format shown in the
right figure, enter “Ping
192.168.1.1” and press
Enter. If the system
gives the result shown
in the right figure, the
connection between
your computer and the
router is OK.
8
Page 14
D840R ADSL2+ Router User Guide
3.3 Logging in to the Router
1． Open the web browser,
and enter
“http://192.168.1.1
the address field, and
then press Enter.
2．In the pop-up login
window, enter the user
name (“admin”) and
password (“admin”),
and click “OK” (both
user name and
password are “admin”
by default).
” in
3．If the user name and
password entered are
correct, the browser
displays the
administrator window
shown right.
9
Page 15
D840R ADSL2+ Router User Guide
Chapter 4 Quick Installation Guide
In the Wizard page, Select
the required your
“Country” and “Area” from
the drop-down lists. If
you can not find your
country and city in these
lists, you can consult your
ISP and manually enter
the VPI and VCI values of
your area. After that, click
“Next”.
10
Page 16
D840R ADSL2+ Router User Guide
4.1 Configure the PPPoE
1． Select “PPP over Ethernet
(PPPoE)”. Click “Next”.
2． Enter the PPP user name
and password provided
by the ISP. If the ISP also
provides the PPPoE
service name, you can
enter the corresponding
value; otherwise, keep
this field null. Use the
default values for other
options. For their more
settings, refer to the
detailed description in the
Advanced Settings.
11
Page 17
D840R ADSL2+ Router User Guide
3． Click “Next” and check to
enable the WAN service
(enabled by default).
4． Click “Next” to display the
window shown the
summary of your settings.
5．Click “Save/Reboot” to
activate your settings.
The system
automatically establishes
connection in a few
minutes.
12
Page 18
D840R ADSL2+ Router User Guide
4.2 Configure the PPPoA
1 ． Select “PPP over ATM
(PPPoA)”. Click “Next”.
2. Enter the PPP user
name and password
provided by the ISP. If
the ISP also provides
the PPPoA service
name, you can enter
the corresponding
value; otherwise, keep
this field null. Use the
default values for other
options. For their more
settings, refer to the
detailed description in
the Advanced Settings.
13
Page 19
D840R ADSL2+ Router User Guide
3. Click “Next” and check
to enable the WAN
service (enabled by
default).
4. Click “Next” to display
the window shown the
summary of your
settings.
5. Click “Save/Reboot” to
activate your settings.
The system
automatically
establishes connection
in a few minutes.
14
Page 20
D840R ADSL2+ Router User Guide
4.3 Configure the MER
1. Select “MAC
Encapsulation Routing
(MER)”. Click “Next”.
2. If your ISP provides the
static IP address, you
should enter the
corresponding values in
“WAN IP Address” and
“WAN Subnet Mask”.
15
Page 21
D840R ADSL2+ Router User Guide
3. If your ISP provides the
dynamic IP address,
you should select
“Obtain an IP address
automatically”.
4. Click “Next”. In the
case of multiple
computers share the
Internet access service,
it is recommend- ed to
enable NAT and
firewall.
16
Page 22
D840R ADSL2+ Router User Guide
5. Click “Next” to display
the window shown the
summary of your
settings.
6. Click “Save/Reboot” to
activate your settings.
The system
automatically
establishes connection
in a few minutes.
17
Page 23
D840R ADSL2+ Router User Guide
4.4 Configure the IPoA
1. Select “IP over ATM
(IPoA)”. Click “Next”.
2. Enter the fixed IP
address and subnet mask
in corresponding fields.
3. Click “Next”. It is
recommended to enable
the NAT and firewall.
18
Page 24
D840R ADSL2+ Router User Guide
4. Click “Next” to display
the window shown the
summary of your
settings.
5. Click “Save/Reboot” to
activate your settings.
The system automatically
establishes connection in
a few minutes.
19
Page 25
D840R ADSL2+ Router User Guide
Chapter 5 Configuration Description
5.1Device Information
1) Click “Running Status”
and “Summary” to
display the “Device
Info” and “DSL Info”
window.
2) The device information
covers:
a. Board ID
b. Software version
c. Boot version
d. LAN MAC address
e. WAN MAC address
f. Running time
g. System time
20
Page 26
D840R ADSL2+ Router User Guide
3) The DSL information
covers:
a. Upstream link rate
b. Downstream link rate
c. LAN IP address
d. Default gateway: In the
pure bridge mode,
there is no gateway; in
other modes such as
PPPoE and PPPoA, the
gateway address is the
IP address of the
upstream device.
e. Primary DNS server: In
the PPPoA/PPPoE mode,
the DNS address is
obtained from the
upstream device; in the
pure bridge mode, it is
not required to set the
DNS address; in other
modes, you can
manually enter the DNS
address.
f. Secondary DNS server
21
Page 27
D840R ADSL2+ Router User Guide
4) Click “WAN” in left
menu to display the
window shown in the
right figure. From the
table, you can know the
general information on
WAN.
5) Click “Route” to display
the window shown in
the right figure,
displaying the default
information.
22
Page 28
D840R ADSL2+ Router User Guide
5.2 Advanced Settings
5.2.1 WAN
Click “WAN”. If the WAN
information has been set,
you can edit or modify it in
this window.
Caution: After modifying/
adding new information,
you need to reboot the
device to activate the
setting.
1) VPI (Virtual Path Identifier):
Virtual path between two
points in the ATM network.
Its value ranges 0 ~ 255.
2) VCI (Virtual Channel
Identifier): Virtual channel
between two points in the
ATM network. Its value
ranges 32 ~ 65535 (1 ~ 31
are reserved for the
well-known protocols).
23
Page 29
D840R ADSL2+ Router User Guide
3) Service category: Selecting
one from five available
service categories.
4) Enable Quality of Service
(QoS): check to enable it.
24
Page 30
D840R ADSL2+ Router User Guide
PPPoA mode
1) Select “PPP over ATM
(PPPoA)”.
Encapsulation Mode:
VC/MUX
LLC/ENCAPSULATION
Once you select one mode,
the system automatically
changes the encapsulation
mode into the one
matching your setting.
Therefore, it is
recommended to keep the
default setting unchanged.
25
Page 31
D840R ADSL2+ Router User Guide
2) Click “Next” to display the
window shown in the right
figure.
a. Authentication Method:
AUTO/PAP/CHAP/MSCHAP
. Usually, “AUTO” is
selected.
b. Dial on demand:
If you check this option,
you need to manually
enter the timeout time. If
no flow is detected when
the timeout time is up, the
device will disconnect the
network connection
automatically. And when a
flow is detected, the
device automatically
makes dial-up connection
again.
If you disable this option,
the device is always in
online status until device
power-off, connection
failure or other failures
occur.
26
Page 32
D840R ADSL2+ Router User Guide
C. PPP IP extension:
When the integrated
gateway is connected with
a computer, the IP address
obtained through the
upstream link is directly
allocated to this computer
connecting with the
device. After the PPP IP
extension is enabled, you
can enable the advanced
DMZ. At this time, you
need to enter your DMZ
host and subnet mask.
d. Use Static IP Address:
After this option is
checked, the device uses
this IP address as the WAN
IP address and does not
need to obtain it through
the upstream link.
e. Retry PPP password on
authentication error
f. Enable PPP debugging
mode.
27
Page 33
D840R ADSL2+ Router User Guide
3) Click “Next” to display the
window shown in the right
figure.
a. Enable IGMP Multicast:
IGMP agent. For example,
to enable the IPTV in the
PPPoE mode, you need to
check this option.
b. Enabled WAN Service:
Checked by default. It is
recommended to keep this
default setting, unless you
do not need to activate
your WAN.
28
Page 34
D840R ADSL2+ Router User Guide
4) Click “Next” to display the
window shown in the right
figure. This window shows
the general information
set.
5) Click “Save/Reboot” to
activate your settings.
29
Page 35
D840R ADSL2+ Router User Guide
PPPoE mode
1) Select “PPP over
Ethernet (PPPoE)”.
Encapsulation Mode:
VC/MUX
LLC/SNAP-BRIDGING
Once you select one
mode, the system
automatically changes
the encapsulation mode
into the one matching
your setting. Therefore,
it is recommended to
keep the default setting
unchanged.
30
Page 36
D840R ADSL2+ Router User Guide
2) Click “Next” to display
the window shown in
the right figure.
a. Authentication
Method:
AUTO/PAP/CHAP/MSC
HAP. Usually, “AUTO” is
selected.
b. Dial on demand:
If you check this option,
you need to manually
enter the timeout time.
If no flow is detected
when the timeout time
is up, the device will
disconnect the network
connection
automatically. And
when a flow is
detected, the device
automatically makes
dial-up connection
again.
If you disable this
31
Page 37
D840R ADSL2+ Router User Guide
option, the device is
always in online status
until device power-off,
connection failure or
other failures occur.
c. PPP IP extension:
When the device is
connected with a
computer, the IP
address obtained
through the upstream
link is directly allocated
to this computer
connecting with the
device. After the PPP IP
extension is enabled,
you can enable the
advanced DMZ. At this
time, you need to enter
your DMZ host and
subnet mask.
d. Use Static IP Address:
After this option is
checked, the device
32
Page 38
D840R ADSL2+ Router User Guide
uses this IP address as
the WAB IP address and
does not need to obtain
it through the
upstream link.
e. Retry PPP password on
authentication error
f. Enable PPP debugging
mode.
33
Page 39
D840R ADSL2+ Router User Guide
8) Click “Next” to display
the window shown in
the right figure.
a. Enable IGMP Multicast:
IGMP agent. For
example, to enable the
IPTV in the PPPoE
mode, you need to
check this option.
b. Enabled WAN Service:
Checked by default. It
is recommended to
keep this default
setting, unless you do
not need to activate
your WAN.
34
Page 40
D840R ADSL2+ Router User Guide
8) Click“Next” to display
the window shown in
the right figure. This
window lists your
settings.
8) Click “Save/Reboot” to
activate your settings.
35
Page 41
D840R ADSL2+ Router User Guide
MER mode
1) Select “MAC
Encapsulation
Routing(MER)”.
Encapsulation Mode:
VC/MUX
LLC/SNAP-BRIDGING
Once you select one
mode, the system
automatically changes
the encapsulation
mode into the one
matching your setting.
Therefore, it is
recommended to keep
the default setting
unchanged.
36
Page 42
D840R ADSL2+ Router User Guide
2) Click “Next” to display
the window shown in
the right figure.
a. Obtain an IP address
automatically:
If your device
automatically obtains
the IP address, the IP
address and other
parameters will be from
your ISP automatically.
b. Use the following IP
address:
To manually specify an
address, you need to
check this option and
enter your static IP
address and subnet
mask.
c. Obtain default gateway
automatically:
If this option is
checked, the device
automatically obtains
37
Page 43
D840R ADSL2+ Router User Guide
the default gateway
address from the
upstream device.
3) Use the following
default gateway: To
manually enter a
gateway, check this
option.
a. Use IP Address:
After checking “Use the
following default
gateway”, you can enter
a value here.
b. Use WAN Interface:
For the broadband
access device, you
need to enter the IP
address of the
downstream link
interface.
4) Obtain DNS server
address automatically:
If this option is
checked, the device
38
Page 44
D840R ADSL2+ Router User Guide
automatically obtains
the DNS address.
5) Use the following DNS
server address:
To manually enter a
DNS address, check
this option.
a. Primary DNS server
b. Secondary DNS server
6) Click “Next”.
a. Enable IGMP
Multicast: IGMP
agent. For example,
to enable the IPTV in
the PPPoE mode, you
need to check this
option.
b. Enable WAN Service:
Checked by default. It
is recommended to
keep this default
setting, unless you
do not need to
39
Page 45
D840R ADSL2+ Router User Guide
activate your WAN.
7) Click “Next” to display
the window shown in
the right figure. This
window lists your
settings.
8) Click “Save/Reboot” to
activate your settings.
40
Page 46
D840R ADSL2+ Router User Guide
IPoA mode
1) Select “IP over ATM
(IPoA)”.
Encapsulation Mode:
VC/MUX
LLC/SNAP-ROUTING
Once you select a mode,
the system automatically
changes the
encapsulation mode into
the one matching your
setting. Therefore, it is
recommended to keep
the default setting
unchanged.
41
Page 47
D840R ADSL2+ Router User Guide
2) Click “Next” to display
the window shown in the
right figure.
a. WAN IP Address:
Enter the IP address
provided by your ISP.
b. WAN Subnet Mask:
Enter the subnet mask
provided by your ISP.
c. Use the following default
gateway:
You can check this
option.
d. Use IP Address:
Enter the IP address
provided by your ISP.
e. Use WAN Interface:
For the broadband
access device, you need
to enter the IP address of
the downstream link
interface.
3) Use the following DNS
server address:
42
Page 48
D840R ADSL2+ Router User Guide
You can check this
option.
a. Primary DNS server
b. Secondary DNS server
Caution: In the IPoA mode,
DHCP is not supported,
so you need to manually
enter the WAN IP
address, subnet mask,
default gateway, DNS
server and other settings.
43
Page 49
D840R ADSL2+ Router User Guide
4) Click “Next”.
a. Enable NAT:
NAT enables multiple
computers in your LAN
to use the same WAN IP
address for Internet
access. It is
recommended to check
this option.
b. Enable Firewall
It is recommended to
check this option to
avoid some attacks.
c. Enable IGMP Multicast:
IGMP agent. For
example, to enable the
IPTV in the PPPoE mode,
you need to check this
option.
d. Enable WAN Service:
Checked by default. It is
recommended to keep
this default
setting,unless you do
not need to activate your
44
Page 50
WAN.
D840R ADSL2+ Router User Guide
45
Page 51
D840R ADSL2+ Router User Guide
e. Click “Next” to display
the window shown in the
right figure. This window
lists your settings.
g. Click “Save/Reboot” to
activate your settings.
46
Page 52
D840R ADSL2+ Router User Guide
Bridging mode
1) Select “Bridging”.
Encapsulation Mode:
VC/MUX
LLC/SNAP-BRIDGING
Once you select a
mode, the system
automatically changes
the encapsulation
mode into the one
matching your setting.
Therefore, it is
recommended to keep
the default setting
unchanged.
2) Enable Bridge Service:
To select the bridge
mode, you need to
check this option. By
default, this option is
checked.
47
Page 53
D840R ADSL2+ Router User Guide
3) Click “Next” to display
the window shown in
the right figure. This
window lists your
settings.
4) Click “Save/Reboot” to
activate your settings.
48
Page 54
D840R ADSL2+ Router User Guide
5.2.2 LAN
1). IP Address: IP address
used by the router to
connect to the LAN.
This option is set to
192.168.1.1 upon
device delivery. You
can change it as
required.
Caution: After changing
this IP address, you
need to use the new IP
address to access the
Web management
window upon next
login to the router. In
addition, you must set
the default gateway in
each computer in your
LAN to this IP address,
to ensure normal
Internet access.
2). Subnet Mask: Setting
49
Page 55
D840R ADSL2+ Router User Guide
your subnet mask.
3). Enable IGMP Snooping:
Used in the bridge
mode.
4). Standard Mode
5). Blocking Mode
6). Configure the second IP
Address and Subnet
Mask for LAN interface.
Click “Save/Reboot”.
50
Page 56
D840R ADSL2+ Router User Guide
5.2.3 NAT
5.2.3.1. Virtual Server
1) Click “NAT” → “Virtual
Server” to display the
window shown in the
right figure. Here, you
can add or delete your
virtual server settings.
By default, the external
networks cannot access
the IP address of your
internal network.
However, if you need
such access by the
external networks (for
example, you need to
set up the server or
support some special
applications), you
should enable this
function to allow the
access by external
networks.
51
Page 57
D840R ADSL2+ Router User Guide
2) Click “Add” to display
the window shown in
the right figure.
a. Select a Service:
Selecting the service to
be enabled.
b. Custom Server:
Manually entering the
server name.
c. Server IP Address: LAN
IP address for the
server.
Caution: After a service is
selected, the system
automatically opens
the corresponding
port. After you
manually enter a
customized service,
you need to manually
enter the port to be
opened.
52
Page 58
D840R ADSL2+ Router User Guide
d. Click “Save/Apply” to
display the service
added, as shown in the
right figure.
5.2.3.2 Port Triggering
1) Click “Port Triggering” to
display the window
shown in the right figure.
Here, you can add or
delete your port
triggering service
settings.
For some special
applications, you need to
enable some application
ports. Through the port
triggering, you can enable
the automatic opening of
the ports required by
applications.
53
Page 59
D840R ADSL2+ Router User Guide
2) Click “Add” to display the
window shown in the
right figure.
a. Select an application:
Selecting the name of
the service to be
enabled.
b. Custom application:
Manually entering the
service name.
Caution: After a service is
selected, the system
automatically sets the
corresponding port. After
you manually enter a
customized service, you
need to manually enter
the port to be triggered.
3) Click “Save/Apply” to
display the service added,
as shown in the right
figure.
54
Page 60
D840R ADSL2+ Router User Guide
5.2.3.3 DMZ Host
1. Click “DMZ Host” to
display the window
shown in the right
figure.
2. DMZ Host IP Address:
Entering the LAN IP
address for the DMZ
host.
Caution: Opening DMZ
means to open all
ports. In this case,
your computer is
totally exposed to the
public network. Be
cautions to use this
function. Click
“Save/Apply” to
activate the settings.
55
Page 61
D840R ADSL2+ Router User Guide
5.2.3.4 UPNP
1) Click “UPNP” to display
the window shown in the
right figure. Enable
UPnP: Check to Enable
the UPnP (Universal Plug
and Play) function.
UPnP is a kind of
architecture of common
network connection
between the computer
and intelligent
devices/instruments. It
is especially common in
the family application.
Based on the Internet
standards and
technologies (such as
TCP/IP, HTTP and XML),
UPnP enables automatic
connection and
cooperation between
such devices, thus to
make more people can
56
Page 62
D840R ADSL2+ Router User Guide
access the network
(especially the family
network).
Click “Save/Apply” to
activate the settings.
5.2.4 Security
5.2.4.1 IP Filtering
1) Click “Security” → “IP
Filtering” to display the
window shown in the
right figure.
By default, all
outgoing traffic is
allowed. However,
you can set IP filtering
to restrict external
network access by
some computers in
the internal network.
57
Page 63
D840R ADSL2+ Router User Guide
2) Click “Add” to display
the window shown in
the right figure.
a. Filter Name: Setting
the filtering name to
facilitate
identification.
b. Protocol: Selecting one
from four available
protocols: TCP/UDP;
TCP; UDP; ICMP.
c. Source IP address:
Entering the internal
network IP address to
be filtered.
d. Source Subnet Mask:
Entering the subnet
mask corresponding
to the internal network
IP address to be
filtered.
e. Source Port: Entering
the port number of the
internal network IP
address to be filtered.
58
Page 64
D840R ADSL2+ Router User Guide
f. Destination IP
address: Entering the
external network IP
address to be filtered.
g. Destination Subnet
Mask: Entering the
subnet mask
corresponding to the
external network IP
address to be filtered.
h. Destination Port:
Entering the port
number of the
external network IP
address to be filtered.
Based on the above
settings, you can add
your filtering rules.
You can select your
WAN interface.
However, it is
recommended to
keep the default
setting unchanged.
59
Page 65
D840R ADSL2+ Router User Guide
3) Click “Save/Apply”.
4) Click “Incoming” to
display the window
shown in the right
figure.
By default, all
incoming traffic is
restricted. However,
you can set IP filtering
to allow internal
network access by
some external
computers.
60
Page 66
D840R ADSL2+ Router User Guide
5) Click “Add” to display
the window shown in
the right figure.
a. Filter Name: Setting the
filtering name to
facilitate identification.
b. Protocol: Selecting one
from four available
protocols: TCP/UDP;
TCP; UDP; ICMP.
c. Source IP address:
Entering the external
network IP address to
be filtered.
d. Source Subnet Mask:
Entering the subnet
mask corresponding
to the external
network IP address to
be filtered.
e. Source Port: Entering
the port number of the
external network IP
address to be filtered.
61
Page 67
D840R ADSL2+ Router User Guide
f. Destination IP
address: Entering the
internal network IP
address to be filtered.
h. Destination Subnet
Mask: Entering the
subnet mask
corresponding to the
internal network IP
address to be filtered.
i. Destination Port:
Entering the port
number of the internal
network IP address to
be filtered.
Based on the above
settings, you can add
your filtering rules.
You can select your
WAN interface.
However, it is
recommended to keep
the default setting
unchanged.
62
Page 68
D840R ADSL2+ Router User Guide
5) Click “Save/Apply”.
5.2.4.2. Parent Control
1) Click “Time of Day
Restriction” to display
the window shown in
the right figure.
2) Click “Add” to display
the window shown in
the right figure. Here,
you can set a specific
period to restrict
Internet access of a
MAC address.
63
Page 69
D840R ADSL2+ Router User Guide
3) Click “Save/Apply”.
64
Page 70
D840R ADSL2+ Router User Guide
5.2.5 Routing
5.2.5.1 Default Gateway
1) Click “Routing” → “Default
Gateway” to display the
window shown in the right
figure.
Enable Automatic
Assigned Default Gateway:
You can check/uncheck
this option. If you uncheck
this option, you need to
manually enter the default
gateway address and WAN
service. It is recommended
to keep the default setting
unchanged.
2) Click “Save/Apply”.
65
Page 71
D840R ADSL2+ Router User Guide
5.2.5.2 Static Routing
1) Click “Static Route” to
display the window
shown in the right
figure.
Here, you can add/
delete the items of the
static route.
1) Click “Add” to display
the
window shown in the
right figure.
Destination Network
Address: Entering the
network or host for
static route.
Subnet Mask: Entering
the subnet mask
correspond- ing to the
network or host for
static route.
Use Gateway IP
Address: Entering the
66
Page 72
D840R ADSL2+ Router User Guide
gateway address to be
passed by the static
route.
Use Interface: Selecting
the interface
correspond- ing to
your connection mode.
Click “Save/Apply”.
5.2.6. DNS
5.2.6.1 DNS Server
1) Click “DNS Server” to
display the window shown
in the right figure.
2) Enable Automatic
Assigned DNS: After
checking it, the DNS
settings are activated. And
the DHCP server of the
router allocates the added
DNS address to the client
67
Page 73
D840R ADSL2+ Router User Guide
submitting the request.
3) Primary DNS server:
Entering the DNS address
provided by the ISP.
4) Secondary DNS server: If
your ISP provides two DNS
addresses, you can enter
the other address here.
5.2.6.2 Dynamic DNS
68
Page 74
D840R ADSL2+ Router User Guide
1) Click “Dynamic DNS” to
display the window
shown in the right
figure. Here, you can
add/ delete the
dynamic DNS settings.
Dynamic DNS can make
your applied domain
name correspond to
your IP address, so that
the other users only
need to remember your
domain name for
accessing your server.
69
Page 75
D840R ADSL2+ Router User Guide
2) Click “Add” to display
the window shown in
the right figure.
D-DNS provider:
Selecting a specific
provider of dynamic
DNS.
Hostname: Domain
name applied by you.
Interface: Selecting one
from two available
interface modes.
Username: Your user
name registered on the
website of the dynamic
DNS provider.
Password: Password
corresponding to your
user name registered
on the website of the
dynamic DNS provider.
70
Page 76
D840R ADSL2+ Router User Guide
3) Click “Save/Apply”.
71
Page 77
D840R ADSL2+ Router User Guide
5.2.7 DSL
Click “DSL” to display
the window shown in
the right figure.
Here, you can enable a
service as required. By
default, the system
checks the status of
G.dmt, G.lite, T1.413,
ADSL2, ADSL2+,
AnnexL, Inner pair and
Bitswap. The device can
automa- tically
negotiate with the
upstream device.
72
Page 78
D840R ADSL2+ Router User Guide
5.3 DHCP
i. Click “DHCP Server” to
display the window
shown in the right
figure.
1. You can click “Disable
DHCP Server” or
“Enable DHCP Server”.
2. Start IP Address: Start
address of the DHCP
server IP pool
3. End IP Address: End
address of the DHCP
server IP pool
. Leased Time: Validity
period of the IP address
obtained. Click “Save”.
Click “DHCP Client List”
to view the list of the
clients with allocated
DHCP service.
5.4 System Tool
73
Page 79
D840R ADSL2+ Router User Guide
5.4.1 Settings
1. Click “Backup” to
display the window
shown in the right
figure. Here, you can
back up the current
settings of the router.
2．Click “Update” to
display the window
shown in the right
figure. Here, you can
restore the router
settings from the
backup file.
74
Page 80
D840R ADSL2+ Router User Guide
3． Click “Restore Default”
to display the window
shown in the right
figure.
Click “Restore Default
Settings” to restore
the default settings
before device delivery.
Caution: After restoring
the default settings,
you need to reboot the
router to activate this
modification.
75
Page 81
D840R ADSL2+ Router User Guide
5.4.2 System Log
1. Click “System Log” to
display the window
shown in the right
figure.
2. Click “View System
Log” to display the
window shown in the
right figure.
76
Page 82
D840R ADSL2+ Router User Guide
3. Click “Configure
System Log” to display
the window shown in
the right figure.
(1) Log: Enable; Disable
(2) Log Level: Selecting
the required level,
Debugging by default.
(3) Display Level: Error by
default.
(4) Mode: Local by
default. If you select
“Remote” or
“Local/Remote”, the
system transmits the
log UDP packets to
your log server.
Click “Save/Apply”.
77
Page 83
D840R ADSL2+ Router User Guide
5.4.3 Internet Time
1. Click “Internet Time”
to display the window
shown in the right
figure. If you enable
this function, the
system can
automatically obtain
the time when
accessing the Internet.
78
Page 84
D840R ADSL2+ Router User Guide
5.4.4 Access Control
5.4.4.1 Service
(1) Click “Access Control”
to display the window
shown in the right
figure. You can
enable or disable
FTP/HTTP/ICMP/SNM
P
/SSH/TELNET/TFTP.
(2) Click “Save/Apply” to
activate the settings
79
Page 85
D840R ADSL2+ Router User Guide
5.4.4.2 IP address
(1) Click “IP Address” to
display the window
shown in the right
figure. Here, you can
add/delete items.
Access Control Mode:
Enable; Disable. When
you enable it, the IP
address allowed can
access the
management page.
(2) Click “Add” to display
the window shown in
the right figure. You
can enter an IP address,
which is allowed by the
system for access- ing
the management page.
Click “Save/Apply” to
activate the settings.
80
Page 86
D840R ADSL2+ Router User Guide
5.4.4.3 Password
(1) Click “Password” to
display the window
shown in the right
figure. Here, you can
modify the password
for logging in to the
Management page.
Enter the former login
password, and then the
new login password. If
the former login
password is correctly
entered, you can click
“Save/Apply” to
successfully modify the
login password.
Caution: For the sake of
security, we highly
recommend you to
change the initial user
name and password.
(2) Click “Save/Apply” to
activate the
modification.
81
Page 87
D840R ADSL2+ Router User Guide
5.4.5 Software Update
1． Click “Update Software”
to display the window
shown in the right
figure. Click “Browse”
to select your update
file, and then click
“Update Software”.
5.4.6 Save/Reboot
1． Click “Save/Reboot” to
display the window
shown in the right
figure.
Rebooting device can
activate the changed
settings. However, the
ADSL connection is
automatically
interrupted before the
reboot.
82
Page 88
D840R ADSL2+ Router User Guide
Chapter 6 Appendix
Appendix 1: Troubleshooting
Trouble Case Troubleshooting
Power Indicator
Off
ADSL Off
LAN Off
Check if the power adapter is
Connected properly.
Check if the power adapter is matched.
Check if the ADSL cable connection is
OK.
Make sure the telephone line is OK
you’re your phone.
Check the phone line cabling is right.
Check the Ethernet cable is OK.
Make sure the PC’s NIC indicator is ON.
Make sure the NIC works normally.
83
Page 89
D840R ADSL2+ Router User Guide
Can’t access the
Internet
Make sure the above troubles are clear.
Make sure the dial-up connection is
established and set up.
Make sure the user name and password
are right.
If the dial-up is OK, please make sure
the IE proxy server is configured
properly.
Please try opening multiple web pages
84
Page 90
D840R ADSL2+ Router User Guide
Appendix 2: FAQ
Q: What are VPI, VCI?
A: VPI (Virtual Path Identifier) and VCI (Virtual Channel
Identifier) are to identify ATM terminal (ADSL) for
DSLAM, usually provided the local ISP.
Q: What related parameters are required from your ISP?
A: For dial user, Connection protocol, User name,
Password, Value of VPI/VCI, Encapsulation mode and
so on.
Q: The firmware upgrade fails and I can’t enter the
Web-based management interface?
A: Contact the technical engineer for support or
after-sales service engineer.
Note:
please download the upgrade packets from the
Tenda website.
Q: Have completed all configurations, but can’t dial
through computer?
A: 1) Check the indicator of ADSL, it should be working
in normally.
2) Check the accuracy of parameter of value of
85
Page 91
D840R ADSL2+ Router User Guide
VPI/VCI, Encapsulation mode and so on.
3) Make sure the dial-up connection is established.
4) You can check whether your ADSL Modem
succeeds in connection through PING command.
86
Loading...