Tenda CP6 Installation Manual

Micro SD

Reset

Quick Installation Guide

Security Pan/Tilt Camera 2K

CP6

This guide is applicable to the Ethernet port version and non-Ethernet port version of Security Pan/
Tilt Camera 2K. The Ethernet port version is used for illustration unless otherwise specified.

For product or function details, please go to www.tendacn.com to download the user guide.

Camera x 1 Power adapter x 1

Anchor x 2

(Height: 6.6 mm, Inner diameter:2.4 mm,

Length:26.4 mm)

Quick Installation Guide

Security Pan/Tilt Camera 2K

CP6

This guide is applicable to the Ethernet port version and non-Ethernet port version of Security Pan/Tilt

Camera 2K. The Ethernet port version is used for illustration unless otherwise specified.

(BA3 x 25 mm, Head diameter:6.0 mm)

Quick installation guide x 1

Screw x 2

Base x 1

Installation template x 1

AppearancePackage contents Add the camera to TDSEE App

Tips:

Before adding your camera, please ensure that the router is connected the internet successfully and the filter
function is disabled.

① Power on the camera.

The LED indicator lights solid red after the camera is powered on. When the LED
indicator blinks blue quickly, it indicates the camera is waiting to connect to a 2.4 GHz
Wi-Fi network.

Internet

Router

LED indicator

LED indicator

Ethernet port

Reset button

Micro SD card slot

Micro SD card slot

Reset button

Speaker

Ethernet port

Microphone

Solid red: Initializing and starting.
Blinking red slowly: Disconnected from a 2.4 GHz Wi-Fi network.
Blinking red quickly: Connecting to a 2.4 GHz Wi-Fi network.
Solid blue: Connected to a 2.4 GHz Wi-Fi network.
Blinking blue slowly: Upgrading.
Blinking blue quickly: Waiting to connect to a 2.4 GHz Wi-Fi network.

10/100Mbps auto-negotiation Ethernet port, used for connecting the router, switch, etc.

Hold down the Reset button for about 5 seconds and release it when the LED indicator blinks blue quickly or you hear a prompt tone. The camera is reset successfully.

Turn the lens upward, then you can see it.

LAN PWR

Power port

LAN PWR

② Download the TDSEE onto your mobile device by searching for TDSEE in the App Store

or Google Play or by scanning the QR code.

Or

QR code

③ Run the TDSEE App and follow the instructions to complete user registration. Enter the

Home page, tap the Add a device or the upper right corner of the home page .

十

④ Scan the QR code on the bottom of the camera, and follow the instructions in the App.

all the de

Inst

The camera supports desktop, ceiling and wall installations. This guide takes ceiling
installation as an example.

Tips:

— Please make sure the ceiling is strong enough to withstand three times the weight of the camera and base.
— You may need a hammer drill, a drill bit, a screwdriver, and a ladder for the installation. Please prepare them by

yourself.

vice

① ②

Ceiling

Installation
template

Drill bit diameter: 6 mm
Hole depth: 28-32 mm

③ ④

Buckle

Anchor

Base

Screw

After finishing the ceiling installation, in order to facilitate monit
camera installation status.
Methods: Run the TDSEE App. Choose the camera on the home page, and tap Settings

（ in the upper right corner）> Video Flip-over, choose Camera UP-side Down.

oring, you need to adjust the

Slot

FAQ

Q1. What should I do when I failed to add the camera?

A1. Try the following solutions:

— Ensure that the router is connected to the internet successfully.
— The Security Pan/Tilt Camera 2K only supports 2.4 GHz Wi-Fi network. When adding the Security

Pan/Tilt Camera 2K, you need to connect the smartphone to a 2.4 GHz Wi-Fi network.

— Do not hide the Wi-Fi network of the router when adding the Security Pan/Tilt Camera 2K (After

adding the Wi-Fi network successfully, you can hide the Wi-Fi network).

— Confirm whether the LED indicator of the camera blinks blue quickly. If not, please reset the camera

configure it again.

and

Reset method: Hold down the Reset button for about 5 seconds and release it when the LED
indicator blinks blue quickly or you hear a prompt tone. The Security Pan/Tilt Camera 2K is reset
successfully.

Q2. What should I do when the video preview is not smooth?

A2. Try the following solutions:

— Check if the Wi-Fi network of the router is smooth.
— Move the router closer to the camera.
— When previewing the video with cellular data, make sure that the internet connection of the smartphone
is smooth.
— Auto, Fluent, and HD are supported for video preview. By default, it is Auto. You can adjust the video
clarity according to the internet status.

Q3. How to store the video?

A3. Try the following solutions:
Method 1: Install the Micro SD card to the camera. By default, the camera's recording mode is Alarm

Recording, which can be set to All-day Recording through TDSEE App. Method: Run TDSEE

App, choose the Security Pan/Tilt Camera 2K on the home page, then tap Settings( in the
upper right corner)→ Recording Settings, choose All-day Recording.

Method 2: Subscribe Cloud Storage Service on TDSEE App. Method: Run TDSEE App, choose the camera

on the home page, and then tap Cloud Storage in the lower left corner. You can enjoy free cloud
storage service (7-days loop detection recording) for 3 months upon the first activation.

CE Mark Warning

This is a Class B product. In a domestic environment, this product may cause radio interference, in which case
the user may be required to take adequate measures. This equipment should be installed and operated with
minimum distance 20cm between the device and your body. The mains plug is used as disconnect device,
the disconnect device shall remain readily operable.
NOTE: (1) The manufacturer is not responsible for any radio or TV interference caused by unauthorized
modifications to this equipment. (2) To avoid unnecessary radiation interference, it is recommended to use a
shielded RJ45 cable.

Declaration of Conformity

Hereby, SHENZHEN TENDA TECHNOLOGY CO., LTD. declares that the radio equipment type CP6 is in
compliance with Directive 2014/53/EU.
Hereby, SHENZHEN TENDA TECHNOLOGY CO., LTD. declares that the radio equipment type CP3 is in
compliance with Directive 2014/53/EU
The full text of the EU declaration of conformity is available at the following internet address:
http://www.tendacn.com/en/service/download-cata-101.html
Operating Frequency:

2.4 GHz: US/2412-2462MHz(CH1-CH11),2422-2452MHz(CH3-CH9)
Conducted Power (Max):

2.4 GHz: 15.74dBm
Software Version: V1.0.X

Adapter Model: BN073-A09009U
Manufacture: SHENZHEN HEWEISHUN NETWORK TECHNOLOGY CO.,
LTD. Input: 100-240V AC, 50/60Hz 0.4A
Output: 9V DC, 1A
: DC Voltage

Caution:

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more
of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may cause undesired operation.

Radiation Exposure Statement

This device complies with FCC radiation exposure limits set forth for an uncontrolled environment and it also
complies with Part 15 of the FCC RF Rules.
This equipment should be installed and operated with minimum distance 20cm between the device and your
body.

Caution:

Any changes or modifications not expressly approved by the party responsible for compliance could void the
user's authority to operate this equipment.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Operating frequency: 2412-2462MHz

NOTE: (1) The manufacturer is not responsible for any radio or TV interference caused by unauthorized
modifications to this equipment. (2) To avoid unnecessary radiation interference, it is recommended to use a
shielded RJ45 cable.

RECYCLING

This product bears the selective sorting symbol for Waste electrical and electronic equipment (WEEE). This
means that this product must be handled pursuant to European directive 2012/19/EU in order to be recycled
or dismantled to minimize its impact on the environment.
User has the choice to give his product to a competent recycling organization or to the retailer when he buys
new electrical or electronic equipment.
Operating Temperature: 0°C - 40°C
Operating Humidity: (10% - 95%) RH, non-condensing

Technical Support

Shenzhen Tenda Technology Co., Ltd.
6-8 Floor, Tower E3, NO.1001, Zhongshanyuan Road, Nanshan District, Shenzhen, China. 518052
USA hotline: [phone]
Toll Free: 7 x 24 hours
Canada hotline: [phone]
Toll Free: Mon - Fri 9 am - 6 pm PST
Hong Kong hotline: [phone]
Global hotline: [phone] (China Time Zone)
Website: www.tendacn.com
E-mail: [e-mail]

Copyright

© 2020 Shenzhen Tenda Technology Co., Ltd. All rights reserved.
Tenda is a registered trademark legally held by Shenzhen Tenda Technology Co., Ltd. Other brand and
product names mentioned herein are trademarks or registered trademarks of their respective holders.
Specifications are subject to change without notice.