Page 1
TRB140
Copyright © 2020, Teltonika Networks. Specifications and information given in this document are subject to change by Teltonika Networks without prior notice.
Page 2
HARDWARE
FRONT VIEW
DATASHEET // TRB140
BACK VIEW
Power LED
Power socket
Ethernet port
Mobile network
type LEDs
USB port
Mobile antenna
connector
POWER SOCKET PINOUT
Copyright © 2020, Teltonika Networks. Specifications and information given in this document are subject to change by Teltonika Networks without prior notice.
Reset button
Mobile signal strength
indication LEDs
2
Page 3
FEATURES
MOBILE
Mobile module
Bridge
Status
SMS/Call
ETHERNET
LAN
NETWORK
Network protocols
Routing
Connection monitoring
Firewall
DHCP
QoS / Smart Queue
Management (SQM) (planned)
DHCP
DATASHEET // TRB140
4G (LTE) – Cat 4 up to 150 Mbps, 3G – Up to 42 Mbps, 2G – Up to 236.8 kbps
Direct connection (bridge) between mobile ISP and device on LAN
Signal strength (RSSI), SINR, RSRP, RSRQ, EC/IO, RSCP Bytes sent/received
SMS status, SMS configuration, Call utilities
1 x RJ45 port, 10/100/1000 Mbps, supports auto MDI/MDIX
TCP, UDP, IPv4, IPv6, ICMP, NTP, DNS, HTTP, HTTPS, SSL v3, TLS, PPP, SSH, DHCP, MQTT, Wake on LAN (WOL)
Static routing
Ping Reboot, Periodic Reboot, LCP and ICMP for link inspection, Wget
Port forwards, traffic rules, custom rules
Static and dynamic IP allocation
Traffic priority queuing by source/destination, service, protocol or port
Supported >25 service providers, others can be configured manually
SECURITY
Authentication
Firewall
Access control
Pre-shared key, digital certificates, X.509 certificates
Pre-configured firewall rules can be enabled via the WebUI, unlimited firewall configuration via CLI; NAT; NAT-T
Flexible access control of TCP, UDP, ICMP packets, MAC address filter
VPN
OpenVPN
OpenVPN Encryption
IPsec
GRE
PPTP, L2TP
Multiple clients and a server can run simultaneously, 12 encryption methods
DES-CBC, RC2-CBC, DES-EDE-CBC, DES-EDE3-CBC, DESX-CBC, BF-CBC, RC2-40-CBC, CAST5-CBC, RC2-64-CBC, AES-128-CBC,
AES-192-CBC, AES-256-CBC
IKEv1, IKEv2, supports up to 5 x VPN IPsec tunnels (instances), with 5 encryption methods (DES, 3DES, AES128, AES192, AES256)
GRE tunnel
Client/Server services can run simultaneously
MONITORING & MANAGEMENT
WEB UI
FOTA
SSH
SMS
MQTT
JSON-RPC
Modbus
RMS
HTTP/HTTPS, status, configuration, FW update, CLI, troubleshoot, system log, kernel log
Firmware update from sever, automatic notification
SSH (v1, v2)
SMS status, SMS configuration
MQTT Broker, MQTT publisher
Management API over HTTP/HTTPS
Modbus TCP status/control
Teltonika Remote Management System (RMS)
SYSTEM CHARACTERISTICS
CPU
RAM
FLASH memory
Copyright © 2020, Teltonika Networks. Specifications and information given in this document are subject to change by Teltonika Networks without prior notice.
ARM Cortex-A7 1.2 GHz CPU
128 MB (50 MB available for userspace)
512 MB (200 MB available for userspace)
3
Page 4
FIRMWARE / CONFIGURATION
WEB UI
FOTA
RMS
Keep settings
FIRMWARE CUSTOMIZATION
Operating system
Supported languages
Development tools
INPUT/OUTPUT
Configurable I/O
Events
POWER
Connector
Input voltage range
PoE (passive)
Power consumption
DATASHEET // TRB140
Update FW from file, check FW on server, configuration profiles, configuration backup, restore point
Update FW/configuration from server
Update FW/configuration for multiple devices
Update FW without losing current configuration
RutOS (OpenWrt based Linux OS)
Busybox shell, Lua, C, C++
SDK package with build environment provided
2 x Configurable Digital Inputs/Outputs
SMS status
4 pin industrial DC power socket
9 – 30 VDC (4 pin industrial socket), reverse polarity protection, surge protection >33 VDC 10μ max
Passive PoE over spare pairs. Possibility to power up through LAN port, not compatible with IEEE802.3af and 802.3at standards
< 5 W
PHYSICAL INTERFACES (PORTS, LEDS, ANNTENAS, BUTTONS, SIM)
Ethernet
I/Os
USB
Status LEDs
SIM
Power
Anntenas
Reset
1 x RJ45 port, 10/100/1000 Mbps
2 x Configurable Digital Inputs/Outputs on 4 pin power connector
Virtual network interface via USB
3 x connection type status LEDs, 5 x connection strength LEDs, 2 x LAN status LEDs, 1x Power LED
1 x SIM slot (Mini SIM – 2FF), 1.8 V/3 V
4 pin DC connector with 2 x configurable Digital Inputs/Outputs
1 x SMA for LTE
Restore factory settings button
PHYSICAL SPECIFICATION
Casing material
Dimensions
Weight
Mounting options
Aluminum housing
64.4 x 74.5 x 25 mm (L x W x H)
134 g
Bottom and sideways DIN rail, Flat surface and direct PCB on DIN-Rail mounting options
OPERATING ENVIRONMENT
Operating temperature
Operating humidity
Ingress Protection Rating
-40 °C to 75 °C
10 % to 90 % non-condensing
IP30
REGULATORY & TYPE APPROVALS
Regulatory
Copyright © 2020, Teltonika Networks. Specifications and information given in this document are subject to change by Teltonika Networks without prior notice.
CE/RED, EAC, RoHS, WEEE
4
Page 5
EMI
Standards
ESD
RS
EFT
Surge protection
CS
DIP
RF
Standards
SAFETY
Standards
DATASHEET // TRB140
Draft ETSI EN 301 489-1 V2.2.0, Draft ETSI EN 301 489-19 V2.1.0, Draft ETSI EN 301 489-52 V1.1.0
EN 61000-4-2:2009
EN 61000-4-3:2006 + A1:2008 + A2:2010
EN 61000-4-4:2012
EN 61000-4-5:2014
EN 61000-4-6:2014
EN 61000-4-11:2004
EN 300 511 V12.5.1, ETSI EN 301 908-1 V11.1.1, ETSI EN 301 908-1 V11.1.2, EN 301 908-2 V11.1.2, ETSI EN 301 908-13 V11.1.2
IEC 62368-1:2014(Second Edition), EN 62368-1:2014+A11:2017
EN 50385:2017
EN 62232:2017
Copyright © 2020, Teltonika Networks. Specifications and information given in this document are subject to change by Teltonika Networks without prior notice.
Copyright © 2020, Teltonika. Specifications and information given in this document are subject to change by Teltonika without prior notice.
5
Page 6
HARDWARE INSTALLATION
1. Unscrew two back panel hex bolts.
2. Remove the back panel.
3. Insert your SIM card into the SIM socket.
4. Attach the panel and tighten the hex bolts.
5. Attach the mobile antenna (max torque 0.4 N·m / 3.5 lbf·in) and connect the USB cable.
DATASHEET // TRB140
LOGIN TO DEVICE
1. Power on the device and connect the USB cable to your computer.
2. Allow the gateway to boot up. This might take up to 30 seconds.
3. Your computer's OS should detect the USB device and install the driver.
4. To enter the gateway's Web interface (WebUI), type http://192.168.2.1 into the URL field of your Internet browser.
5. Use login information shown in image A when prompted for authentication.
6. After logging in pay attention to the Signal Strength indication displayed in the Mobile widget (image B). To maximize the cellular
performance try adjusting the antennas or changing the location of your device to achieve the best signal conditions.
A. B.
-65 dBm
admin
admin01
Data connection state
State
SIM card slot in use
Bytes received/sent*
Registered (home); OPERATOR; 4G (LTE)
TECHNICAL INFORMATION
Radio specifications
RF technologies
Max RF power
2G, 3G, 4G
33 dBm@GSM, 24 dBm@WCDMA, 23 dBm@LTE
Bundled accessories specifications*
Power adapter Input: 0.4A@100-240VAC, Output: 9VDC, 0.5A, 4-pin plug
Mobile antenna 698~960/1710~2690 MHz, 50 Ω, VSWR<2, gain** 2 dBi, omnidirectional, SMA male connector
Connected
Ready
348.7 KB / 223.5 KB
*Order code dependent.
**Higher gain antenna can be connected to compensate for cable attenuation when a cable is used. The user is responsible for the compliance with the legal regulations.
Copyright © 2020, Teltonika Networks. Specifications and information given in this document are subject to change by Teltonika Networks without prior notice.
6
Page 7
WHAT'S IN THE BOX?
STANDARD PACKAGE CONTAINS
• TRB140 board
• Euro PSU
• 1 x LTE antenna (magnetic mount, SMA male, 3 m cable)
• Micro-USB cable (0.8 m)
• 1 x hex key
• LAN cable
• QSG (Quick Start Guide)
• Packaging box
DATASHEET // TRB140
TRB140
EURO PSU
1 X LTE ANTENNA (MAGNETIC
MOUNT, SMA MALE, 3 M CABLE)
1 X HEX KEY ETHERNET CABLE (1.5 M)
MICRO-USB CABLE (0.8 M)
Copyright © 2020, Teltonika Networks. Specifications and information given in this document are subject to change by Teltonika Networks without prior notice.
7
Page 8
DATASHEET // TRB140
STANDARD ORDER CODES
PRODUCT CODE PACKAGE CONTAINSHS CODE HTS CODE
TRB140003000
TRB140003000 851762 8517.62.00 Standard Package, no housing
For more information on all available packaging options – please contact us directly.
851762 8517.62.00 Standard Package
AVAILABLE VERSIONS
PRODUCT CODE FREQUENCYREGION (OPERATOR)
4G (LTE-FDD): B1, B3, B7, B8, B20, B28A
TRB140 0*****
TRB140 1*****
Europe, the Middle East, Africa, Korea,
Thailand, India, Malaysia
South America, Australia, New Zealand,
Taiwan, Malaysia
4G (LTE-TDD): B38, B40, B41
3G: B1, B8
2G: B3, B8
4G (LTE-FDD): B1, B2, B3, B4, B5, B7, B8, B28
4G (LTE-TDD): B40
3G: B1, B2, B5, B8
2G: B2, B3, B5, B8
The price and lead-times for region (operator) specific versions may vary. For more information please contact us.
1 - Versions for other regions are under development.
2 - For more detailed information, visit our Wiki
Copyright © 2020, Teltonika Networks. Specifications and information given in this document are subject to change by Teltonika Networks without prior notice.
8
Page 9
MOUNTING OPTIONS
DIN RAIL KIT
Parameter
Mounting standard
Material
Weight
Screws included
Dimensions
RoHS Compliant
DIN RAIL KIT
DIN Rail adapter
Philips Pan Head screw #6-32×3/16, 2pcs for RUT2xx/RUT9xx
ORDER CODE HTS CODEPRODUCT CODE HS CODE
088-00267
For more information on all available packaging options – please contact us directly.
Value
35mm DIN Rail
Low carbon steel
57g
Philips Pan Head screw #6-32×3/16, 2pcs
82 mm x 46 mm x 20 mm
V
PR5MEC00 73269098 7326.90.98
DATASHEET // TRB140
COMPACT DIN RAIL KIT
Parameter
Mounting standard
Material
Weight
Screws included
Dimensions
RoHS Compliant
DIN RAIL KIT
Compact plastic DIN Rail adapter (70x25x14,5mm)
Philips Pan Head screw #6-32×3/16, 2pcs
ORDER CODE HTS CODEPRODUCT CODE HS CODE
088-00270
For more information on all available packaging options – please contact us directly.
Value
35mm DIN Rail
ABS + PC plastic
6.5 g
Philips Pan Head screw #6-32×3/16, 2pcs
70 mm x 25 mm x 14,5 mm
V
PR5MEC11 73269098 7326.90.98
SURFACE MOUNTING KIT
Parameter
Mounting standard
Material
Weight
Screws included
Dimensions
RoHS Compliant
Value
Flat surface mount
ABS + PC plastic
2x5 g
Philips Pan Head screw #6-32×3/16, 2pcs
25 mm x 48 mm x 7.5 mm
V
DIN RAIL KIT
Surface mounting kit
Philips Pan Head screw #6-32×3/16, 2pcs
ORDER CODE HTS CODEPRODUCT CODE HS CODE
088-00281
For more information on all available packaging options – please contact us directly.
Copyright © 2020, Teltonika Networks. Specifications and information given in this document are subject to change by Teltonika Networks without prior notice.
PR5MEC12 73269098 7326.90.98
9
Page 10
TRB140 SPATIAL MEASUREMENTS & WEIGHT
MAIN MEASUREMENTS
H x W x D dimensions for TRB140
Device housing*:
Box:
*Housing measurements are presented without antenna connectors and screws; for measurements of other device elements look to the sections below.
TOP VIEW
The figure below depicts the measurements of TRB140 and its components as seen from the top:
64.4 x 74.5 x 25
173 x 148 x 71
DATASHEET // TRB140
RIGHT VIEW
The figure below depicts the measurements of TRB140 and its components as seen from the right side:
Copyright © 2020, Teltonika Networks. Specifications and information given in this document are subject to change by Teltonika Networks without prior notice.
10
Page 11
FRONT VIEW
The figure below depicts the measurements of TRB140 and its components as seen from the front:
DATASHEET // TRB140
REAR VIEW
The figure below depicts the measurements of TRB140 and its components as seen from the back:
Copyright © 2020, Teltonika Networks. Specifications and information given in this document are subject to change by Teltonika Networks without prior notice.
11
Page 12
MOUNTING SPACE REQUIREMENTS
The figure below depicts an approximation of the device's dimensions when cables and antennas are attached:
DATASHEET // TRB140
Copyright © 2020, Teltonika Networks. Specifications and information given in this document are subject to change by Teltonika Networks without prior notice.
12
Page 13
DIN RAIL
The scheme below depicts protrusion measurements of an attached DIN Rail:
DATASHEET // TRB140
Copyright © 2020, Teltonika Networks. Specifications and information given in this document are subject to change by Teltonika Networks without prior notice.
13
Loading...