Telstra T165i User Manual

1

Telstra T165i

HSDPA Multi band 3G Mobile Phone

User Manual

2

PC Software Requirements

Join Me PC Software included supports Microsoft Vista (only 32 bit), Windows 2000 with Service Pack 4 or

Windows XP with Service Pack 2 only. A limited version of Join Me is provided that supports MAC. 64 Bit

systems are NOT supported.

Warnings and Safety Notices

Please read all the safety notices in section 1.2 and 16 before using this device.

Copyright © 2008 ZTE Corporation All rights reserved.

2nd Edition November 2008

No part of this publication may be excerpted, reproduced, translated or utilized in any form or by any means,

electronic or mechanical, including photocopying and microfilm, without the prior written permission of ZTE

Corporation.

ZTE Corporation operates a policy of continuous development. ZTE Corporation reserves the right to make

changes and improvements to any of the products described in this document without prior notice.

Limitation of Liability

ZTE shall not be liable for any loss of profits or indirect, special, incidental or consequential damages

resulting from or arising out of or in connection with using this product, whether or not ZTE had been

advised, knew or should have known the possibility of such damages. The user should refer to the

enclosed warranty card for full warranty and service information.

3

RF Safety Information

The handset has an external antenna located at the top of the phone. For optimum performance with

minimum power consumption always extend the antenna during a call and do not cover the antenna

area with your hand. Hold the handset between thumb and finger in the middle of the device.

Covering the antenna affects call quality, may cause the handset to operate at higher power level

than needed, and may shorten talk and idle times.

Radio Frequency Energy

The handset is a low-power radio transmitter and receiver. When switched on it intermittently

transmits radio frequency (RF) energy (radio waves). The transmit power level is optimized for best

performance and automatically reduces when there is good quality reception. Maximum power is

only used at the edge of network coverage so under most circumstances the power output is very low.

Under poor network conditions the phone will transmit at a higher power, may get hot and will have

a significantly shorter battery life.

Declaration of Conformity

We declare under our sole responsibility that the product(s) detailed in this manual, and in

combination with our accessories, conform with the essential requirements of The Radio

Communications Standard (Electro-magnetic Radiation Human Exposure) 2003 and the Australian

Communications and Media Authority Section 376 of the Telecommunications Act 1997.

N14945

4

Contents

1 Welcome 9

1.1 How to use the manual 10

1.2 Handset Overview 11

1.3 Keypad Functions 13

1.4 Information Bar Icons 14

1.5 Menu Quick Reference Guide 15

2 Getting Started 17

2.1 How do I insert the USIM Card? 17

2.2 How do I insert the Battery? 18

2.3 How do I switch the phone On or Off? 19

2.4 How do I connect the charger? 19

2.5 Tips about charging and battery life 20

2.6 How do I set the time and date? 20

2.7 How do I lock the keypad? 20

3 Basic Operation 21

3.1 How do I make a voice call? 21

3.2 How do I answer an incoming call? 21

3.3 How do I send a Text Message (SMS)? 21

3.4 How do I navigate the Menus? 22

4 Contacts 23

4.1 How do I enter my Contacts? 23

4.2 How do I copy all Contacts from a USIM card? 23

4.3 How do I search my Contacts? 23

4.4 How do I add a Contact from a received call number? 24

4.5 How do I add a Contact from a received SMS (Text Message)? 24

4.6 How do I set a dedicated ringtone or image to a Contact? 24

5

4.7 How do I set Speed Dial numbers? 25

4.8 How do I make a call using Speed Dial? 25

4.9 How do I update an existing Contact? 25

4.10 Advanced Contact Options 26

5 Calls 27

5.1 How do I make a Voice Call? 27

5.2 How do I make a Voice Call from my Contacts? 27

5.3 How do I view and make a Voice Call from my Call History? 27

5.4 Call options during an active Voice Call 28

5.5 How do I activate Speakerphone? 28

5.6 How do I answer a Call? 29

5.7 How do I make a Video Call? 29

5.8 Call options during an active Video Call 30

5.9 How do I answer a Video Call? 30

5.10 How do I make Emergency Calls? 31

5.11 Videophone Setting 32

5.12 Call Divert 32

5.13 Call Waiting 32

5.14 Call Barring 33

5.15 Send my number 33

5.16 Missed Calls Alert 34

5.17 Call Options when Connected to a Bluetooth device 34

6 Messages and Emails 35

6.1 How do I send a Text Message (SMS)? 35

6.2 How do I view a received Text Message (SMS)? 35

6.3 How do I use Predictive Text? 36

6.4 How do I add words to the built in Dictionary (My Words)? 37

6

6.5 Special Characters and SMS Message Length 37

6.6 How do I send a Multimedia Message (MMS)? 38

6.7 How do I receive a Multimedia Message (MMS)? 38

6.8 MMS Settings 38

6.9 WAP Push Messages 39

6.10 How do I send an Email? 39

6.11 How do I receive an Email? 40

6.12 How do I set up automatic Email Retrieval? 40

6.13 Pushmail Settings 40

7 How to Personalise the Phone 41

7.1 Change the Profiles 41

7.2 Change the Shortcut Keys (Arrow keys) 42

7.3 Change the Background Screen (Wallpaper) 42

7.4 Change the default Ringtones 43

7.5 Enable Vibrate Mode 43

7.6 Engage Meeting Mode with a single key press 43

7.7 Switch the Keytones off 43

7.8 Change the Screen Brightness 44

7.9 Change the Display Backlighting 44

7.10 Set the Keypad backlighting 44

7.11 Add a Greeting and Owner name 44

7.12 What is the PIN Code? 45

7.13 What is the Handset Code? 45

7.14 Additional notes on PIN Codes 45

8 File Manager and External Memory 46

8.1 File Manager 46

8.2 Installing Additional Memory - microSD card 47

7

8.3 Access the T-Flash card (microSD) using File Manager 48

8.4 File Manager and T-Flash Options Table 48

9 Alarms and Appointments 49

9.1 Set Alarms 49

9.2 Set Appointments using the Calendar 50

10 Imaging - Pictures and Videos 51

10.1 How to use the Camera 51

10.2 How to use the Video Camera 52

10.3 Viewing pictures and videos 53

11 Music 54

11.1 FM Radio 54

11.2 Browse and play music files from File Manager 54

11.3 Create a new Playlist 55

12 Assisted-GPS 56
13 Connectivity 57

13.1 Use Join Me to connect the phone to a computer 57

13.2 Installing Join Me 58

13.3 Use Join Me to copy photos to your computer 59

13.4 Use Join Me to transfer music from a computer 61

13.5 Enter Contacts using Join Me 63

13.6 Copy Contacts from the phone to the computer 64

13.7 Import Contacts from Microsoft Outlook 65

13.8 Import Calendar events from Microsoft Outlook 66

13.9 Use Join Me to connect to the Internet 66

13.10 Connect to a Bluetooth Device 67

13.11 Dial Up Networking using USB or Bluetooth 69

13.12 PC Connection 71

8

13.13 Synchronize with a network server (SyncML) 71

14 Other Facilities 72

14.1 Browser 72

14.2 Stopwatch 73

14.3 Calculator 73

14.4 World Time 73

14.5 Currency Conversion 74

14.6 PocketNews 74

14.7 Games and Applications 74

14.8 Voice Recorder 75

14.9 Slide Show 75

14.10 Streaming URL 75

14.11 Connections 75

14.12 Access Point Settings 76

14.13 Restore default settings 76

14.14 Auto Keylock 76

14.15 Download Location 77

14.16 Network Settings 77

14.17 CTM 78

15 Technical, Support and Warranty Information 79

15.1 Troubleshooting and FAQ’s 79

15.2 Error Messages 81

15.3 Technical Parameters 82

15.4 Support Information 83

15.5 Warranty Information 83

16 Environmental Statement 84
17 General Safety and Maintenance Information 85

9

1 Welcome

Congratulations on choosing the Telstra T165i handset. Please take a few minutes to read the

user guide to help you get the most from your new mobile phone

Operation Quick Reference

Handset overview, keypad and information bar Section 1 – Introduction

Making a call Section 2 – Getting Started

Quick introduction to key features, Calls and SMS Section 3 – Basic Operation

Store a list of contact names and phone numbers Section 4 – Contacts

View calls received, dialled and missed Section 5 – Calls

Text messages – sending and receiving Section 6 – Messages and Emails

Personalise your phone, e.g. ringtone, screen saver Section 7 – Personalise

Managing handset files and content Section 8 – File Manager

Setting alarms and reminders Section 9 – Alarms and Appointments

Using the camera – take photos, record a video Section 10 – Imaging

FM radio, MP3’s and access to music libraries Section 11 – Music

Using GPS Section 12 – Assisted GPS

Connecting to a PC to copy pictures and music Section 13 – Connectivity

Calculator, Stopwatch and more Section 14 – Other Facilities

Accessing the internet, BigPond, Whereis®, etc See your Telstra Next G guide

10

1.1 How to use the manual

The following conventions are used in the manual:

Instruction Description

Press the Left Arrow ◄ Press the left directional key on the four way controller

Press OK Press the OK key in the centre of the four way controller

Press the Right Soft Key Press the key just below the screen.

Long press Press and hold the key for 2 seconds.

Menu > Tools Go to the Main Menu (press OK) select Too ls and press OK to open

• The functions for the OK and Soft keys change depending on where you are in the menu.

The functions are always described at the bottom of the handset display.

• The End or Exit key

is used to exit the menus, end a Call and switch the handset On or

Off. From within a sub-menu the Exit key takes you back to the main menu

• Long press the

key to switch the handset On and Off.

• The C key is used to go back one step in menus, and to clear text in text edit modes. In text

edit mode press once for backspace, press and hold to clear all the text.

• The symbol shows useful tips.

Menu and setting choices on the handset are shown in bold grey text in the manual.

Quickly find the answer to any question you may have, check the Contents at the front

of the manual or visit the Index at the back of the manual.

There is a copy of the manual and quick start guide provided on your CD

11

1.2

Handset Overview

1. Extendable Antenna

2. Earpiece

3. Four way controller -

Arrow Keys(◄►▲▼)

4. Left Soft Key (LSK)

5. Call Key, show Call History

6. Video Call Key

7. Keypad

8. Microphone

9. Clear Key *

10. End / Exit / Power Key

11. Right Soft Key (RSK)

12. OK Key

13. Camera for video calling

* The C key is used to go back one step in menus,

and to clear text in text edit modes.

In text modes press once for backspace,

press and hold to clear all the text.

13

1

12

2

3

9

5

6

4

11

10

7

8

12

Handset Overview

Charger / USB /
Headset port
(Slide to open)

Camera key

Right

Volume keys

Left

Speaker

Camera

External Antenna port

(must be open for

car-kit insertion)

microSD Port

Rear

13

1.3 Keypad Functions

Key Corresponding Functions Key Corresponding Functions

1 1 | punctuation marks | voicemail

2 2 | abc | ABC

3 3 | def | DEF

4 4 | ghi | GHI

*

Long press for keylock

Special characters in text modes

Press twice for the international prefix ‘+’

Press three times for the pause character ‘P’

5 5 | jkl | JKL #

Toggle text modes. Long press for Silent

6 6 | mno | MNO

7 7 | pqrs | PQRS

Call

Open All Calls list

Call a dialled or selected number

8 8 | tuv | TUV

9 9 | wxyz | WXYZ

0 0 | Space

End

End a call.

Exit a menu

Long press to power ON / OFF

14

1.4 Information Bar Icons

3G Signal Strength

Battery Level Indicator

GSM Signal Strength

Alarm is set

Signal Strength of the EDGE Network

Missed Call

New SMS or MMS Message

Missed Video Call

SMS or MMS Memory is Full

Silent Mode

New E-mail

Vibrate mode enabled

E-mail Memory is Full

Call Forward is Active

New Wap Push Message

GPRS Attach

Wap Push Message Memory is Full

PDP Context Established (Data)

Headset and Vibrate Mode

High speed data, HSDPA mode

Headset Mode

Roaming

Bluetooth is ON

Car kit attached

A-GPS is ON

15

1.5 Menu Quick Reference Guide

1) BigPond

2) Messages

1 New Message

2 Inbox (0/0)

3 Outbox (0)

4 Drafts (0)

5 Sent (0)

6 User folders

7 (U)SIM Inbox

8 Settings

9 Memory info.

> E-mail

1 New Email

2 Inbox (0/0)

3 Outbox (0)

4 Drafts (0)

5 Sent (0)

6 User folders

7 Settings

8 Memory info.

3) Calls

A. Call log

1 All calls

2 Missed calls

3 Received calls

4 Dialled calls

>

B. Calls Info.

Call duration

4) Camera 5) My Place

1 BigPond

2 FOXTEL

3 Yellow

4 Scan Code

5 My Email

6 Call 1234

7 Music

8 Whereis

9 Blog&Photo

10 Downloads

11 My Account

6) Multimedia

1 Camera

2 Video camera

3 FM Radio

4 Media player

5 Playlist

6 Slide show

7 Streaming URL

8 Voice recorder

9 Games & Apps

7) STK (SIM Tool Kit)

Pocket News

> My Favorites

> News

> Finance

> Weather

> Horoscope

> Sport Scores

> Surf Report

16

8) Contacts

All

> USIM

> Family

> Friends

> Work

> VIP

> Unclassified

9) Tools
1 Browser
2 Alarm
3 Stopwatch
4 Calculator
5 World Time
6 Bluetooth
7 Syncml
8 Currency Conversion
9 GPS

*)Calendar

View appointments.

Add a

Meeting

Memo or

Reminder

0) File Manager

Photos

Audios

Videos

Others

> TFlash Card

#) Settings

A. Screen

1 Wallpaper

2 Display Backlighting

3 Set brightness

4 Keypad Backlighting

5 Owner name

6 Greeting

B. Handset
1 Language
2 Time and date
3 Network settings
4 Own phone number
5 Shortcut keys
6 Connections
7 Access point settings
8 Restore default settings
9 Keylock
10 Network time
11 Download location
12 PC Connection
13 CTM
14 Missed calls alert

C. Profiles

1 General

2 Meeting

3 Outdoor

4 Silent

5 Car kit

D. Security

1 Activate security codes

2 Change security codes

3 Fixed dial numbers

4 FDN list

E. Call

1 Videophone settings

2 Call divert

3 Call waiting

4 Call barring

5 Send my number

17

2 Getting Started

2.1 How do I insert the USIM Card?

The USIM card (UMTS Subscriber Interface Module) is the small plastic smart-card with gold contacts.

It holds personal information such as names and phone numbers. It can be moved between different

phones if required. The USIM card must be inserted before using the handset.

• Insert the USIM card with the gold contacts facing down and the bevelled edge on the left hand

side as shown. Carefully slide it under the metal bar observing the correct orientation.

If your handset displays: “No (U)SIM detected” please check the USIM is inserted correctly.

“Enter PUK code” please contact your Service Provider.

“Enter Unlock code” please contact your Service Provider.

18

2.2 How do I insert the Battery?

Insert the battery as shown with the contacts located against the gold springs. The battery will only

fit one way.

Close the case by locating the plastic cover horizontally into the grooves and sliding the cover up to

close it. Do NOT force the cover down by pressing on it. This can damage the cover.

Slide the cover up gently

Locate the cover into the grooves horizontally and slide up gently.

19

The Information bar

2.3 How do I switch the phone On or Off?

Press and hold the key for two seconds to switch the phone ON or OFF.

The start up screen below is referred to throughout the manual as the Idle Screen:

The Idle Screen

2.4 How do I connect the charger?

Slide the charger port to open. Charge before initial use. The charger lead only fits one way. The plug is

marked with an arrow. Always insert the charger lead carefully with the arrow facing the top of the

phone as shown:

Do NOT use excessive force which may damage the USB socket.

Physical damage to the USB port is NOT covered by warranty.

The phone can also be charged by connecting it to a

computer using the USB lead supplied.

If the phone is off after charging long press the End

20

Key to switch it back on.

2.5 Tips about charging and battery life

• Only use the AC charger and USB lead supplied.

• Insert the charger lead carefully with the arrow facing the top of the phone.

• Normal charge time is 2-3 hours. Do not leave on charge for more than 24hrs

• When not using the phone for long periods remove the battery.

• Charge the battery between 0°C~50°C. Charge the battery promptly when flat.

• With poor network conditions (less than 2 bars) battery life is reduced.

• To maximize battery life turn off Bluetooth when not in use and limit multimedia functions.

• The phone can be charged in the ON or OFF state. When the phone is OFF you will see the Charging

Battery animation. When the phone is ON the battery icon will animate.

• If charging in the OFF state turn the phone ON by long pressing the key.

2.6 How do I set the time and date?

The time and date is set automatically from the network. It takes a few seconds to update when the

phone is first switched on. Select 12 or 24 hr format in the Network Time menu. To manually set the

time it is necessary to switch Network Time off: Menu > Settings > Handset > Network Time > State Off

then set the time and date manually: Menu > Settings > Handset > Time and date.

2.7 How do I lock the keypad?

Manual keylock: Long press the * key then press the right soft key to engage or disengage keylock.

Auto keylock: Menu > Settings > Handset > Keylock Set your desired time to lock the keypad. See 14.14.

21

3 Basic Operation

3.1 How do I make a voice call?

• Enter the number on the keypad and press the key to make the call.

• Press OK to activate Handsfree (speakerphone) mode

• Press the key to end the call.

3.2 How do I answer an incoming call?

• Press or OK to answer the call.

• Press or Reject to end the call.

If Voicemail is active pressing Reject will forward the call to Voicemail .

3.3 How do I send a Text Message (SMS)?

• Press the Right Arrow ► for Messages

• Press OK for New Message. Press OK for Text Message

• Enter the phone number directly or press OK to select from Contacts

• Select the Contact then press OK for Done. The Contact number will be displayed, press OK

• Press the Down Arrow ▼ twice to move the cursor into the text field

• Type the message using the letter keys on the keypad (see Chapter 6 on Texting)

• Press the OK to send the message.

22

3.4 How do I navigate the Menus?

The Main Menu is a grid of icons that are used to access key features on the phone.
From the Idle Screen press OK to access the Main Menu. Use the Arrow Keys ▲▼◄►to move to the

desired icon. The icons are described at the bottom of the screen.

OK

Shortcuts

From the idle screen the Arrow Keys launch the Shortcuts as shown:

My Place

Email Messages

Contacts

To change default shortcuts: Menu > Settings > tab right to Handset > Shortcut keys

From sleep mode (dark screen) press the key once to wake up the handset, press the key again

to perform the required function.

Use the number keys to select icons from the grid. ie Press Menu > 1 to select BigPond

23

4 Contacts

4.1 How do I enter my Contacts?

• From the Idle Screen enter the phone number on the keypad, press the Left Soft Key to Save.

• Press OK to create a New Contact or press the Down Arrow ▼to Update existing contact

• Using the keypad, enter a name for the new Contact or modify an existing contact

• Press OK to Save. The default save location is the USIM card. Change if required.

4.2 How do I copy all Contacts from a USIM card?

All USIM Contacts are automatically read by the handset.

To copy Contacts into the handset memory follow the steps below:

• Insert the USIM card you wish to copy contacts from. Switch the phone on.

• From the idle screen press the Down Arrow ▼ for Contacts.

• Press the Right Arrow ►once for USIM to show the list of Contacts on the USIM card.

• Press the Left Soft Key for Options then use the arrow keys to select, Copy > Copy all > OK > Yes to

confirm.

4.3 How do I search my Contacts?

From the idle screen press the Down Arrow ▼ for Contacts. To find the Contact ‘Joh n ’ press t h e 5 k e y

once for ‘J’. All names starting with ‘J’ will be displayed.

Refine the search by entering a subsequent letter that can occur anywhere in the name.

Eg. ‘J n ’ wil l find ‘John’ a nd ‘Juli a n ’ but n o t ‘J ames ’ where a s ‘J a ’ wil l f i nd J u lian a n d Jame s b ut not J o hn

24

4.4 How do I add a Contact from a received call number?

After receiving a call you can add the caller’s number to the Contacts list:

• Press the key to display All Calls

• The last call received will be at the top of the list

• Press the Left Soft Key > Options > Save > New Contact or Update to modify a contact > OK

• Enter or modify the contact details and press OK to Save.

4.5 How do I add a Contact from a received SMS (Text Message)?

Menu > Messages > Inbox

• Select the required message and press OK to View

• Press Options > Use highlight object to save the number

• Choose New Contact to create a new contact from the received SMS number.

4.6 How do I set a dedicated ringtone or image to a Contact?

The contact needs to be stored on the handset in order to set a dedicated ring or image. See 4.2

Menu > Contacts (Shortcut = Down Arrow ▼)

• Use the arrow keys ▼▲ to find the required contact (must be stored on the handset)

• Press OK to View > Edit > Options > Add ring and photo. Select the required feature

• Press Add then navigate to the folder where the Ringtone or Picture is stored.

• Press OK to Save your choices when complete

25

4.7 How do I set Speed Dial numbers?

Having Speed Dials set makes it quicker to call selected contacts.

Menu > Contacts > Select the Contact > Options > Scroll down ▼ > Set Speed Dial > Setup

• Assign the chosen contact to the next available number

• Speed dials 1, 2 and 3 are preset and cannot be changed

• Press the OK Key to Setup the speed dial or press OK Key again to cancel

• Press the key to exit when finished.

4.8 How do I make a call using Speed Dial?

• From the Idle screen press and hold the required number key to call that Contact

• E.g. A long press on the 1 key will automatically dial the Voicemail service.

4.9 How do I update an existing Contact?

• Edit the existing contact: Menu > Contacts > View > Edit. Press Save when finished

• Contacts are normally stored in the default Group, All

• You can move contacts into other Groups: Family, Friends, Work, and VIP.

• Search for a contact by pressing the letter keys that correspond to the contact name

• Refine the search by entering a subsequent letter that can occur anywhere in the name.

Eg. ‘J n ’ wil l find ‘John’ a nd ‘Juli a n ’ but n o t ‘J ames ’; ‘J a’ wi l l f i nd Jul i an a n d Jame s but no t J ohn

26

4.10 Advanced Contact Options

Menu > Contacts > Options

Option Description or subsequent options

Call Make a Voice Call or Video Call to the selected contact

Send Send an SMS, MMS or E-mail to the selected contact

New Contact Create a new contact

Edit Contact Edit the selected contact

Delete Delete contact, Delete all (Phone), Delete all (USIM), Delete all (Both)

Copy Copy to phone, Copy all

Send Bus. Card Send a business card via SMS, MMS, E-mail or Bluetooth

Default Memory Default save location for contacts, USIM card or Phone

Service Dial number Preset Voicemail and Video-mail message bank numbers

Speed dial Assign a speed dial to the selected contact

Manage Contact

Set Group parameters (eg Ringtone and photo), Speed dial info and check

the memory status

27

5 Calls

5.1 How do I make a Voice Call?

• Enter the number on the keypad and press the key to make a voice call.

• Press OK to activate Handsfree or Speakerphone (Loudsp.)

• Press the key to end the call.

5.2 How do I make a Voice Call from my Contacts?

• Press the Down Arrow ▼(default shortcut) for the Contacts menu.

• Use the Arrow Keys ▼▲ to scroll to the chosen contact.

• Search Contacts using the letter keys – eg. p ress ‘J’ to fin d John

• Press the key to make the call.

• Press the key to end the call.

5.3 How do I view and make a Voice Call from my Call History?

• Press the key to bring up All Calls. Press again for Last Number Redial

• Use the Arrow Keys ▼▲ to choose a number from the All calls list

• Press the key to make the call.

• Press the key to end the call.

28

5.4 Call options during an active Voice Call

Press the Left Soft Key for Options during a voice call. Use the End key to return to the call menu

Hold: Puts the current call on hold

End call: End the call

Record: Record the current call. The audio file is saved to the My Audios folder

DTMF Off/On: Enable or disable sending DTMF tones. Default is ON

Message: Switch to SMS interface during a call

Contacts: Switch to Contacts interface during a call

Browser: Launch the web browser

5.5 How do I activate Speakerphone?

Handsfree or Speakerphone is activated by pressing OK (Loudsp.) during a call

• To dial an International number press the star key twice for the International Prefix ‘+’

• To call a number received within a message highlight the number then press the Call key

• The microphone is on the base of the handset. Be careful not to block it with your hands

• During a call change the volume using the side Volume keys

• The number of rings before the phone diverts to Voicemail is set by your Service Provider.

The default is 6 rings. Contact your Service Provider to change this setting.

• To enable international roaming please contact your Service Provider.

29

5.6 How do I answer a Call?

When you receive an incoming call:

• The phone will light up, the call alert will sound and the phone will vibrate depending on the

current profile setting.

• You will receive an incoming call notification displayed on the screen

• Press or OK to initiate Speakerphone (Loudsp.) to answer the call.

• Press to Reject the call.

• Press Silence to mute the incoming ring if required. This feature is useful to silence the incoming

ring without answering the call. The other party hears ring tone until the call ends.

5.7 How do I make a Video Call?

3G coverage is required to make and receive video calls.

• Enter the phone number using the keypad or from the Contacts list as already described

• Press to make a video call.

• Press to end the call.

If the call is not successful you will be asked if you want to try a voice call instead.

30

5.8 Call options during an active Video Call

Press the Left Soft Key for the following Options during a video call:

Hold / Retrieve Send a still picture instead of your own image and the voice is muted

Start recording video Record video from the other party (i.e. received video stream)

Block/Send my picture Block / Send your own image to the other party

Use back/front camera Select the back/front camera

Brightness Adjust the brightness

Zoom Change the magnification of your own image

PIP off / on Hide or show your own picture on the local screen

Exchange PIP Reverses the Picture in Picture display, ie. the initiator of the call will

now appear larger

New text message Send SMS during a video call

Contacts Switch to Contacts interface

5.9 How do I answer a Video Call?

3G coverage is required to make and receive video calls. If a video call is received when browsing or

using multimedia functions, the browser, media player or FM radio will be suspended.

When receiving an incoming Video call:

• When receiving an incoming video call the phone will ring, vibrate and illuminate depending on the

current profile setting,

• Press the Video call key to accept the video call,

• Press the End key to end the video call.

31

5.10 How do I make Emergency Calls?

To make an emergency call during normal use

• Ensure that the handset is switched on and in service.

• Press the key repeatedly to return to the Idle Screen.

• Enter the emergency number for the present location using the keypad, (eg 000).

• Press the key to call the number. Follow instructions received and do not end the call until

told to do so.

• If the keypad is locked it is possible to dial the Emergency Numbers without having to unlock the

keypad. Press the numbers as required then press the Call key.

Emergency calls can be made without a USIM Card (Phone PIN not required)

When the USIM card is not inserted or registered it is possible to dial the emergency services.

Enter the emergency number and press or OK to make the call.

• Advise the operator which emergency service you require

• Give your position and remain stationary to get the best coverage

• Due to the nature of the cellular system the connection of emergency calls cannot be

guaranteed

• Never rely solely on any wireless device for essential communications ie. medical emergencies

• The Emergency Number 112 is used internationally.

32

Advanced Call Settings

5.11 Videophone Setting

Menu > Settings > tab right to Call > Videophone settings

All the fields are preset by your Service Provider. If you change Service Providers you may need to

update these settings. Contact your Service Provider for more details.

5.12 Call Divert

Menu > Settings > tab right to Call > Call divert

This service enables incoming calls to be diverted to another number. Choose the Call divert function

required from the menu list. From the functions listed select the feature you wish to Activate,

Deactivate or Check status.

5.13 Call Waiting

Menu > Settings > tab right to Call > Call Waiting

This feature allows an incoming call to be answered while already on a call. Answering the incoming

call will automatically place the first call on hold. The handset displays a table showing the Active call

and call on Hold. Pressing Options allows the switching between the ‘Active’ and ‘Hold’ calls.

Press Options to switch calls between Hold and Active:

03991234xx Active Press Options > Hold to switch calls

03996543xx Hold Press Options > Active to switch calls

33

5.14 Call Barring

Menu > Settings > tab right to Call > Call barring

Call barring is a network feature. The barring password is provided by your service provider. The service

needs to be enabled on your account. To obtain your PIN number contact your Service Provider.

Bar all outgoing calls: Calls cannot be made.

Bar outgoing calls (international): International calls cannot be made.

Outgoing International Calls except

for calls to the home country

Restricts international calls except to your home country

Bar all incoming calls: Calls cannot be received.

Bar incoming calls when roaming Calls cannot be received when you are overseas

Cancel all call barring Cancels all barring settings

Change password Set password to activate or erase call barring.

5.15 Send my number

Menu > Settings > tab right to Call > Send my number

Send or hide your number when making calls. Switch it on or off. The default set by the network is On.

34

5.16 Missed Calls Alert

Menu > Settings > tab right to Handset > Missed calls alert

After missing a call, the missed call icon will be displayed on the information bar.

When the Missed call alert is set the reminder tones will sound at your specified interval for 5 times or

until the on screen message is acknowledged.

After a missed call press the green call key to display the All Calls list.

Press the green call key again to dial the last number.

5.17 Call Options when Connected to a Bluetooth device

If the handset is connected to a Bluetooth accessory such as a car kit or a wireless headset then an

incoming call is forwarded to the Bluetooth device. Press the Call key on the Bluetooth device to

answer the call. When idle press the call key on the Bluetooth device to initiate Last Number Redial on

the handset. The handset does not support Contacts over Bluetooth. See Section 13.10 for more details

An active call can be switched between the Bluetooth device and the handset by pressing:

Options > Switch to Handset / Switch to Bluetooth.

35

6 Messages and Emails

6.1 How do I send a Text Message (SMS)?

Right Arrow ►New Message > Text Message or
Menu > Messages > New Message > Text Me ssage

• Press the OK Key to select from Contacts (Cont.) or enter the number manually.

• Scroll to the chosen contact and press OK twice (once to select and once to confirm)

• Press the Down Arrow ▼ twice (once to add extra contacts, once again to enter the text area)

• The default text mode is Predictive Text indicated by the En symbol

• Enter text by pressing the corresponding keys once for each required letter eg. 43556 for ‘hello’. The

system updates the display to show the most probable entry. See Section 6.3 for more details.

• Select the desired word from the available list and press OK to confirm or choose Spell Word? to add

a new word to the My Words dictionary.

• Press Options for the My Words dictionary

• Press the # key to toggle between En, 123, ABC and abc text modes.

• When completed press the OK Key to Send the message.

6.2 How do I view a received Text Message (SMS)?

• The envelope icon will appear on the information bar to indicate a received message. The

message alert tone and vibrate activate depending on the current profile setting. Press OK to View

the message.

• Navigate to the Inbox (Menu > Messages > Inbox > OK to Select) to view all received messages.

Scroll to the desired message and press OK to View.

36

6.3 How do I use Predictive Text?

Predictive text allows words to be entered more efficiently using a single keypress for each letter, as

opposed to multiple keypresses in multi-tap text mode. Compare how to write the word ‘the’:

Traditional multi-tap text mode (ABC, abc) Predictive Text Mode (En)
Press 8 (tuv) once to select ‘t’

Press 8 once for ‘t’

Press 4 (ghi) twice to select ‘h’

Press 4 once for ‘h’

Press 3 (def) twice to select ‘e’

Press 3 once for ‘e’

• The default text mode is predictive text indicated by En in the top right corner of the display.

• Press the # key to toggle between different modes En, abc, ABC, 123

• It is not possible to disable predictive text mode or to change the initial mode

• Predictive text uses a built-in dictionary to generate words from the sequence of letters pressed.

• When a word is highlighted press the C key to delete the word, press the # key to change to capitals

as follows: dave, Da ve, DAVE

• Select the desired word from the available list using the ▲▼keys and press OK to confirm or

choose Spell Word? to save to My Words (See 6.4). Unknown words default to Spell Word?

• If the next letter is on the same key, wait until the cursor appears or press the Right arrow ►to

move the cursor on

• To insert a space press the 0 key. Press the C key once to delete single letters, hold to clear all text

• Press the 1 key for common punctuation marks. Press the * key for special characters

• ABC, abc are multi tap modes. Press the key once for the first letter, twice for the second letter etc.

• In text input screens (eg SMS, MMS and E-Mail) you can add your own words to the built-in

Dictionary which is called My Words

• Press the Options key to access My Words to Add new words to the available lists.

37

6.4 How do I add words to the built in Dictionary (My Words)?

• From predictive text mode enter words directly by choosing Spell Word?

• From the text entry screen press the Options key and select My Words

• The first time you use My Words press OK to Add a new word

• Type the new word using the ABC or abc modes then press OK to Save it

• In My Words you can press the Options key to Edit, Delete or Delete all words.

6.5 Special Characters and SMS Message Length

The underlined characters in the above chart are Unicode Characters. This means that they are not

part of the standard SMS character set and they require 2 SMS characters to transmit them. Normal

SMS message length is 160 characters. If exceeded, the message will be sent by two SMS’. When the

underlined characters are used the message length is limited to 70 characters. When 70 characters is

exceeded the message is sent by two SMS’.

38

6.6 How do I send a Multimedia Message (MMS)?

Use a Multimedia Message to send pictures, music or video files to your friends.

Menu > Messages > New Message > Multimedia Message

• Enter the phone number or press OK for Contacts to select a number

• Press the down arrow ▼and enter text in the title field (if required)

• Press the down arrow ▼to enter the text area (main message body)

• From the text area press OK to Insert an Image, Audio or Video file

• Browse the folders to select the required file. Press OK

• When finished press the Right Soft Key to Send

Each ‘page’ can only contain one image, one audio, and one video file. To add more than one

file of the same type, select Options to add a new page.

6.7 How do I receive a Multimedia Message (MMS)?

Menu > Messages > Inbox

• When receiving an MMS you get a standard message alert. Press OK to View.

• Press Retrieve to download the message attachment.

• When the attachment has downloaded press the Left Soft Key for Options.

• Choose Use Highlight Object to Save the file into File Manager

6.8 MMS Settings

Menu > Messages > ▼ Settings > Mul. Msg. Settings

The MMS settings are preset by your Service Provider. If using an alternate Service Provider the MMS

Settings will need to be modified.

39

6.9 WAP Push Messages

Menu > Messages > ▼ Settings > Mul. Msg Settings > Push Messages – Accept or Reject

A WAP push message is a formatted SMS that displays a message to the user, giving the option of

connecting directly to a particular URL via the mobile phone’s WAP browser.

• WAP Push Messages are indicated by the Icon on the main display.

• Use the Browser to view Push Messages. Set to Reject to disable Push Messages

6.10 How do I send an Email?

Menu > Messages > tab right to Email > Settings > Mailbox Settings > Options > Edit

• The default Email client is configured for BigPond

• Add your BigPond username, password and email address

• The username should be the full address: [e-mail]

• It is possible to Add other providers under Mailbox Settings

• Configure the POP Server details, SSL settings, IP Address etc. by reference to the other provider.

Sending an Email

Menu > Messages > tab right to Email > New E-mail

• Enter the sender address e.g. [e-mail]

• Press the down arrow ▼ to access the Copy To Field

• Press the down arrow ▼ to access the Title Field

• Press the down arrow ▼ to enter the Text Field

• Press OK to Insert attachments if required

• Browse to the appropriate folder to add the attachment

• When you are finished press the Right Soft Key to Send.

40

6.11 How do I receive an Email?

Configure the Email Client with your personal settings to enable receiving Emails.

Menu > Messages > tab right to Email > Settings > Mailbox Settings > Options > Edit

• The default Email client is configured for BigPond

• Add your BigPond username, password and email address

• The username should be the full address: [e-mail]

• It is possible to Add other providers under Mailbox Settings

• Configure the POP Server details, SSL settings, IP Address etc. by reference to the other provider.

Send an SMS, MMS or Email to up to 10 recipients

Receiving an Email

Menu > Messages > tab right to Email > Inbox > Options > Retrieve

New Email messages will be delivered to the handset

6.12 How do I set up automatic Email Retrieval?

Menu > Messages > tab right to Email > Settings > Automatic Retrieval

Set your required polling time interval to check the server for new Email messages.

6.13 Pushmail Settings

Menu > Messages > tab right to E-mail > Settings > Pushmail Settings > Receive Pushmail

Pushmail denotes an automatic email retrieval service that is Always On. New emails arriving on your

server are ‘pushed’ to your handset. This feature depends on network support and it is not provided

automatically by a POP3 server.

41

7 How to Personalise the Phone

There are many ways to customise the handset such as changing the profiles, wallpaper, ringtones,

setting up shortcuts etc.

7.1 Change the Profiles

Menu > Settings > tab right to Profiles > Edit the required Profile

From the idle screen long press the # key to engage Meeting Mode (silent with vibrate)

Profiles are used to control the preferred ringing mode, keys tones etc. The pre-defined profiles are:

General Keytones ON, Ringing ON, Vibrate OFF

Meeting Keytones OFF, Ringing OFF, Vibrate ON

Outdoor Keytones ON, Ringing ON, Vibrate ON, Ringing FULL volume

Silent Keytones OFF, Ringing OFF, Vibrate OFF

Car Kit Keytones OFF, Ringing ON, Vibrate OFF, Auto answer and Backlighting Always on

The following profile settings can be customised using Edit

Voicecall ringtone Ring volume Message tone Warning Tone

Videocall ringtone Ring type (vibrate etc) Keytones Earpiece volume

The Car Kit profile is only engaged when the device is installed in a car kit and provides 2 extra
features, Auto Answer and Backlighting Always on.

42

7.2 Change the Shortcut Keys (Arrow keys)

The four arrow keys (▲▼◄►) can be customised to launch preferred features quickly from the idle
screen.

Menu > Settings > tab right to Handset > Shortcut Keys > OK

• Set each key in turn to the preferred setting

• Scroll to the chosen feature and press OK to assign the shortcut key.

Example Shortcut Setting:

File Manager

▲

Calendar ◄ ► Messages

▼

Contacts

7.3 Change the Background Screen (Wallpaper)

Menu > Settings > Screen > Wallpaper

• Browse to the required folder eg Photos > My Pictures

• Choose the required picture and press Set to confirm

See Connectivity to import pictures

See Imaging to take photos on the camera

43

7.4 Change the default Ringtones

Menu > Settings > tab right to Profiles > Edit

• Edit the current profile to change the default Ringtones for all incoming calls

• Press OK to Modify the Voicecall ringtone (scroll down to select Videocall ringtone)

• Browse to Audios, Ring to see the available built in tones.

• See Connectivity to import your own music files.

7.5 Enable Vibrate Mode

Menu > Settings > tab right to Profiles > Edit

• Edit the current profile to enable the Vibrate function

• Scroll down▼ to Ringing Type and press OK to Modify

• Select the required mode and press OK to confirm.

• The vibrate icon will be displayed on the Information Bar

7.6 Engage Meeting Mode with a single key press

• Mute the handset and switch it to vibrate mode by long pressing the # key from the Idle Screen:

• Press and hold the # key to engage and disengage Meeting Mode

• The vibrate icon and mute symbol will be displayed on the Information Bar

7.7 Switch the Keytones off

Menu > Settings > tab right to Profiles > Edit

• Scroll down ▼ to Keytones and switch them off.

44

7.8 Change the Screen Brightness

Menu > Settings > Set Brightness

• Use the Up and Down ▲▼ keys to set the desired level.

7.9 Change the Display Backlighting

Menu > Settings > Display backlighting

• Screen full-light is the main screen lighting. After the set time the screen goes to half light

• Screen half-light, the screen is partially lit for the specified time

7.10 Set the Keypad backlighting

Menu > Settings > Keypad backlighting

Duration 30 secs The keys remain illuminated for 30 seconds after the last key press

Always On The keypad backlighting is enabled for the Duration specified

Customise The keypad is only illuminated between the times set

Keypad backlighting is unnecessary during the day so a customised setting will improve

battery life

7.11 Add a Greeting and Owner name

Menu > Settings > Owner name

Menu > Settings > Greeting

• The Owner name is permanently displayed on the idle screen

• The Greeting is displayed during the start up sequence

45

7.12 What is the PIN Code?

Menu > Settings > Security > Activate Security Codes > Pin Code

• The PIN code is stored on the USIM card and protects your account against unwanted use

• Select On or Off and enter the PIN number to confirm. The original PIN number is provided by your

service provider but can be changed if required

• To change the PIN Code select Change Security Codes

• If you forget the PIN code it can be reset by your service provider.

7.13 What is the Handset Code?

Menu > Settings > Security > Activate Security Codes > Handset Code

• The Handset Code is stored on the handset and protects against unwanted use. If the handset is

lost or stolen it cannot be switched on without the handset lock code. This provides a greater level

of protection than the PIN code which protects the USIM card only. The default code is 0000

• Select On or Off and enter the Handset code, 0000.

• To change the Handset Code select Change Security Codes and enter a new code of your choice

• It is important to remember this code as it cannot be reset if it is forgotten.

7.14 Additional notes on PIN Codes

• The PIN and PUK Codes are provided by your Service Provider

• If you enter the PIN number incorrectly three times the phone will be PUK locked

• Contact your service provider to get the PIN Unlocking Key (PUK code)

• PIN2 Code is an additional PIN on the USIM card and is not generally used.

46

8 File Manager and External Memory

All user files and downloaded content are stored in the File Manager.

8.1 File Manager

Menu > Tool s > File Manager

The file manager is separated into four folders, Photos, Audios, Videos and Others as shown:

Folder

Contents Description

Top Animations, Latest Animations Link to BigPond

Top Pics, Latest Pics Link to BigPond

Wallpapers Background screens for the handset

Photos

My Pictures Default directory for handset pictures

Latest Tones, To p Tone s Link to BigPond

Tone of the week Link to BigPond

Ring Pre-loaded handset Ring Tones

Audios

My Audios Storage for your own Audio files (MP3 etc)

Top Videos, Music Videos Link to BigPond

Videos

My Videos Default directory for handset videos

Others

Downloaded Internet files, Java apps etc.

47

8.2 Installing Additional Memory - microSD card

Handset memory can be increased by inserting a microSDHC card up to 4GB.

microSD cards up to 2GB are supported (FAT 16 format)

microSDHC (high capacity) cards up to 4GB are supported (FAT 32 format).

• Open the microSD port cover on the right hand edge of the phone

• Carefully insert the microSD card as shown above

• Close the side cover

• The external memory is accessed through the File Manager application described below.

With the microSD card inserted the default storage location for user photos and videos is the

External Memory. You can set this under Menu > Settings > Handset > Download Location

Always handle memory cards with care and avoid static discharge

48

8.3 Access the T-Flash card (microSD) using File Manager

Menu > Tool s > File Manager > tab right to T-Flash Card

• All the folders and files that are stored on the card are displayed

8.4 File Manager and T-Flash Options Table

Depending on your location within File Manager, there are different Options (Left soft key) available as

shown in the table below:

Folder Options File Options Mark Options

Search Mark Mark all files

New folder Send Unmark all

Delete Set as ringtone / wallpaper Add to playlist / slide

Delete all Add to playlist / slide Move to

Rename Move to Copy to

Folder information Copy to Delete

Space information Rename Delete all

Delete Play marked files

Delete all Space information

Mark all files New folder

File information

Space information

New folder

Press the Options to Mark files to perform the function to multiple file selections.

49

9 Alarms and Appointments

9.1 Set Alarms

Menu > Tool s > Alarm > Add

Configure the alarm as required using the Alarm Setup Screen:

• Daily Alarm goes off every day

• Workday Alarm goes off Mon – Fri only (Rest days can be set under Options)

• Weekly Alarm will go off at the same time each week

• Once Alarm will only go off once

• Snooze can be set to be Off, 5, 10, 15 or 30 minute intervals

• Snooze will repeat for six times or until you Stop the alarm by pressing the OK key

• The Alarm Tone is preset by the Ringfile Press Edit to change if required

• If the Alarm time has passed it cannot be saved

• If the phone is switched off the Alarm will automatically switch on the handset.

Alarm Summary Table

Alarm type Daily, Workday, Weekly, Once

Alarm date Available with Weekly and Once

Alarm time Set as required

Snooze Off, 5, 10, 15, 30 minutes

Ringtone On / Off

Ringfile Alarm.mid, press Edit to change

Status Enable / Disable

Alarm remark Optional

50

9.2 Set Appointments using the Calendar

Menu > Tool s > Calendar > Add

• Add a Meeting, Memo or Reminder. The memo function does not include an alarm

• Use the Meeting function to set repeat events such as Weekly Meetings and Anniversaries

• Follow the prompts on screen to configure the event, see the examples in the table below

• Events are shown by a highlighted box on the event day

• Use Options to see the Week view and to change default behaviour under Settings

• If the Alarm time has passed or is after the event time you cannot save the appointment

• If the phone is switched off the Alarm will automatically switch on the handset.

Examples of different uses for the Calendar > Meeting function

Daily Reminder Meeting with alarm Repeat Meeting Anniversary

Subject Check mail Appointment Weekly Team John’s Birthday

Location Dentist Office

Start time 10.00am 11.00am 10.00am 08.00am

End time 10.00am 01.00pm 11.00am 08.00am

Start date 28/9/08 30/10/2008 29/9/2008 29/03/2009

Alarm set On On On On

Alarm time 09.45am 10.00am 09.45am 08.00am

Alarm date 28/9/08 30/10/2008 29/9/2008 29/3/09

Repeat set Daily Not repeated Weekly Yearly

Repeat until 28/10/08 N/A 29/9/2012 29/03/2030

51

10 Imaging - Pictures and Videos

10.1 How to use the Camera

Menu > Multimedia > Camera

Shortcuts: Press and hold the side camera key to activate the camera.

The camera key activates the shutter and if pressed again will Save the image.

From Still mode press ►to change to Video mode as shown by the icon in the top right

hand corner.

• Use the Up and Down arrows to control the zoom*

• Press the Options button to:

¾ Change the Photo Size**

¾ Change the Photo Quality

¾ Change the Brightness

¾ Change the Contrast

¾ Apply an Effect (Normal, B&W or Sepia)

¾ Change the Shutter sound

¾ Save to – Handset memory or External Memory (SD card if fitted)

¾ Use the front / back camera

¾ Switch to Video Camera

* Zoom is not available on 1200 x 1600 as the screen is at maximum resolution.

** The default photo size is small to enable easy sending by MMS and Email.

To increase the size : Menu > Multimedia > Camera > Options > Photo Size

52

10.2 How to use the Video Camera

Menu > Multimedia > Video Camera

Shortcut: Press and hold the side camera key to activate the camera, press ►to switch

to video mode.

From Video mode press the ◄to change to Still mode as shown by the icon in the top right

hand corner.

• Use the Up and Down arrows to control the zoom

• Press the Options button to change the following:

¾ Video size, default is 15 seconds. Change this if required.

¾ Video Quality

¾ Brightness

¾ Contrast

¾ Effect (Normal, B&W or Sepia)

¾ Video sound

¾ Video format, MP4 or 3GP

¾ Save to – Handset memory or External memory (SD card if fitted)

¾ Use the front / back camera

¾ Switch to Camera

Press My Vids to view your saved video files

When viewing a video press Full Screen to view in Landscape.

53

10.3 Viewing pictures and videos

1. View the file directly from file manager

Menu > Tool s > File Manager > Photos > My Pictures or

Menu > Tool s > File Manager > Videos > My Videos

Scroll down the list to your chosen picture, Press Open to view the image.

2. Create a slide show to view pictures in sequence

Menu > Multimedia > Slide Show > Add > Photos > My Pictures

Select your required photos using Options > Mark and then Save the slide show

Press Start to automatically view the pictures sequentially.

3. View My Pics or My Vids from Camera mode

Menu > Multimedia > Camera > My Pics

Menu > Multimedia > Video Camera > My Vids

Press the Right Soft Key to select My Pics or My Vids to view your saved photos.

Additional features when viewing Pictures and Videos

Still Pictures Videos

Full Screen Right Soft Key Full Screen, Landscape Right Soft Key

Zoom in and out Up and Down Arrows Volume up and down Up and Down Arrows

Rotate the image 1,3 keys Brightness 2,8

Move the image 2,4,6,8

54

11 Music

To import music files onto the handset see the following sections:

• Import music files from your computer using JoinME (See Connectivity)

• Import music files from your computer or other device using Bluetooth (See Connectivity)

• Download music from BigPond Music: Menu > Games and Applications > Downloads

11.1 FM Radio

Menu > Multimedia > FM Radio

• Insert the personal hands free kit (PHF). The headset acts as the antenna for the FM radio.

• Tune the required station using the◄► keys or Options > Auto Search or Set Channel

• Auto Search scans automatically for channels.

• Use Set Channel to enter the frequency using the keypad and * key to access the decimal point

• Remember to Save the new channel.

• Press Options > Rename to personalize the channel name eg ABC

• If an incoming call is received, the radio will be suspended while you answer the call.

11.2 Browse and play music files from File Manager

Menu > Tools > File manager > Audios > My Audios

• Press Open to play the desired music file.

Warning – At high volumes, prolonged listening to audio devices can damage hearing.

55

11.3 Create a new Playlist

Method 1: Create a Playlist from File Manager

Menu > Tool > File Manager > Audios > My Audios

• Scroll through the files and press Options > Mark (or Mark all files) to select files then Press OK

• Press Options > Add to Playlist > OK (for existing Playlist) or Add / New (to create a playlist)

• The selected song or songs will be added to an existing or new playlist

• Menu > Multimedia > Playlist > Scroll to select, OK to Play

Method 2: Create a playlist in Multimedia

Menu > Multimedia > Playlist > Add > Playlist name > OK > Audios > My Audios

• Scroll through the tracks and press Options > Mark to add the selected files to the playlist

• Press OK to save the Playlist, Press OK again to begin playing it

• Once a Playlist has been saved press Options > Edit to add or delete tracks and press Options to

rename, delete etc.

• Press Options to set the Repeat Setting; no repeat, all repeat or shuffle

• Use the side volume keys to adjust the volume

• Use ▲▼ keys to select tracks from your playlist

• Press the ◄► keys to skip tracks

• Press and hold the ◄► keys to forward or rewind through tracks

It is possible to create up to six different playlists.

56

12 Assisted-GPS

A-GPS is an advanced positioning system developed for mobile phone applications. The complex

calculations performed by a GPS receiver are carried out on an external server. Assistance information

is sent to the handset over the cellular system and is dependant on cellular coverage. The handset

contains an antenna and receiver specifically for A-GPS signals and this enables the handset to

calculate its position in terms of longitude, latitude and altitude.

• Stand alone GPS is a limited service pre-installed in the handset, that in good conditions will

provide a decimal location position.

• Full functionality requires additional applications to be installed or supplied by third parties. Please

contact your service provider for more information.

• The GPS receiver requires signals from at least three satellites and can take several minutes to

acquire.

• Reception is reduced in city areas, best reception is achieved with a clear view of the whole sky.

• The signal strength may be reduced in a vehicle, indoors or in overcast weather conditions.

• The antenna is in the top of the phone. Avoid blocking it with your hand to maximize reception

• It is not recommended to utilise stand alone GPS for mission critical applications.

• To switch GPS On or Off go to Tools, GPS Status. Perform a search under GPS Location. Results will

be dependant on the above conditions.

• Regular use of GPS positioning will increase battery consumption.

57

13 Connectivity

13.1 Use Join Me to connect the phone to a computer

Join Me is a program to connect the phone to a computer. After installation Join Me is used to manage

contacts, messages and calendar functions. It is also used to connect to the internet and transfer

music / picture files.

Compatibility

• The software is only compatible with Windows* XP Service Pack 2, Windows* 2000 SP 4 Windows

Vista*, MAC OS 10.5 and 10.4. However Join Me cannot be guaranteed to run on these systems.

• It is not compatible with Windows* ME, 98, 95 or with any 64 bit systems.

• The software may not run in all PC environments, or in conjunction with other software.

• Multi-boot systems are not supported.

• The software should be installed and run under the Administrator login.

Installation

• The following procedures and examples are only applicable to the PC Version of Join Me

• Please follow the installation steps carefully.

• If the installation fails please see the ReadMe file on the CD or consult our web site for more help.

www.zte.com.au.

*Windows, Vista, XP, 2000 and ME are registered trademarks of the Microsoft Corporation.

58

13.2 Installing Join Me

Please install the Join Me CD before connecting the phone to the computer.

• Insert the CD provided into the computer

• The CD will auto-start after a few seconds

• If auto run does not start then run Setup.exe from the CD

• The installation shield will launch and guide you through the installation

• Please follow the prompts to install the software

• When the installation is complete plug the handset into the computer using the USB lead supplied

• The USB lead is unique and should not be used for other devices (It is not the same as digital

camera leads)

• When the handset is plugged in the computer will automatically install the drivers. If this fails

consult our website for more help or access Windows Device Manager to update the drivers. See

www.zte.com.au for instructions

Note

If the phone is connected to the computer before installing the CD then the drivers will not be installed

correctly.

• Unplug the phone, un-install then re-install Join Me

• Press the Help Icon to access the built in Help menu.

• See www.zte.com.au for more assistance

59

13.3 Use Join Me to copy photos to your computer

Transfer photos from the handset to your computer using Join Me:

• Make sure the phone is switched on, connected to the computer and Join Me has been installed.

• The PC Connection on the handset needs to be set to USB

Menu > Settings > Handset > PC Connection > USB

• Connect the phone to the computer using the USB lead supplied

• Double-click the Join Me icon on the desktop.

• Select the phone type and press Connect.

• Select the Media tab as shown on the next page

• Double click on My Phone in the bottom left hand corner

• Double click on Photos to expand the folder structure

• Double click on My Pictures to see the picture files on the right hand side.

• Drag* the required file from the file list and Drop* it into the required destination folder on the PC.

• The file will be copied to the destination folder (Desktop in the example below).

• Files can only be transferred into Folders.

The default picture size is very small when viewed on the computer.

See section 10.1 to change the image size.

* Drag and Drop is a method of copying files. Click on the file, hold down the left mouse button,

move the mouse pointer to the required destination and release the left mouse button to Drop

the file to that location. Alternatively right click on the file and use Copy and Paste from the

menu.

60

Copy files (eg Photos) from the phone to the computer using JoinME

1. Select the Media Tab

2. Select My Pictures folder on My Phone

3. Drag the picture from My Pictures

to a folder on the PC

4. Alternatively right click on the file and

use Copy and Paste from the menu

Files can only be copied into Folders

61

13.4 Use Join Me to transfer music from a computer

Music files can be transferred onto the phone using Join Me.

• Make sure the phone is switched on, connected to the computer and Join Me has been installed.

• The PC Connection on the handset needs to be set to USB

Menu > Settings > Handset > PC Connection > USB

• Double click the Join Me icon on the desktop.

• Select the phone type and press Connect.

• Select the Media tab as shown in the picture on the next page.

• Double click My Phone in the bottom left hand corner.

• Double click Audios to open up the Audios folder.

• Locate the music files on the computer by browsing through the Windows file structure in Join Me.

• Drag the required file from the top half (computer) and drop it into My Audios on the phone.

• The file is copied to the destination folder (as shown below). Files can only be copied into Folders.

• Alternatively Right Click on the file, choose Copy, then go to the destination folder and Paste.

MP3, WAV, WMA and MIDI Files are supported but MP3 is preferable due to smaller file size.

62

Copy files (eg Music) from the Computer to the handset using JoinME

Use drag and drop to copy the

selected file from the computer to

the My Audios folder on the handset.

Alternatively select the file, right click

to Copy the file, select the destination

folder (on the handset) and choose Paste.

Files can only be transferred into user folders

on the handset. Eg. Transfer music files into

My Audios, pictures into My Pictures and Java

games and applications into the Others folder.

All other folders are write protected.

63

13.5 Enter Contacts using Join Me

Use Join Me to enter new contacts into the phone.

.

The save position ‘Local’ refers to the computer. Remember to change this if you want to save

contacts directly to the handset or use the copy function to copy contacts from Local to Phone.

There is less storage available on the USIM card so some of the fields are greyed out.

On the phonebook tab enter

contacts directly using the PC.

Select “New Contact” then

complete the required fields.

Select the Save Position; Local,

Phone ,(U)SIM or All.

64

13.6 Copy Contacts from the phone to the computer

Copy one or all of the contacts from Local to Phone using the same method

2. ‘Select all’ by checking the
box at the top of the list.

3. Drag and drop the complete
list to Local.

This will copy all the USIM
contacts to the PC (Local)

You can also select an
individual contact to copy it in
either direction.

1. Select the USIM card to

copy contacts from the
USIM to the PC.

You can also right click on the
Contacts grid and Import from

Outlook. See 13.7 below…

65

13.7 Import Contacts from Microsoft Outlook

• Launch Microsoft Outlook, load Join Me and connect your handset to the computer.

• Note, at the end of the import process Outlook can shut down. Please save any information

beforehand.

• Select the PhoneBook tab in Join Me, see image in 13.6 above.

• Click on the button and select Import contacts from Outlook.

• Select one of the 3 listed options, Replace with new items, Allow Duplicates or Do not create

duplicates and click OK.

• Only contacts in the root folder (Contacts) of Outlook will be copied

• The following fields are imported from Outlook to Join Me as below:

Outlook Join Me

Full Name Name

Mobile Telephone Number Home mobile

Home Telephone Number Home phone

Business Telephone Number Work mobile

Company Main Telephone Number Work phone

Other Telephone Number Other mobile

Company Name Company

Profession Notes

Web Page Web

66

13.8 Import Calendar events from Microsoft Outlook

• Launch Microsoft Outlook, load Join Me and connected your handset to the computer.

• Note, at the end of the import process Outlook can shut down. Please save any information

beforehand.

• Make sure you are on the Calendar tab in Join Me

• Click on the button and select Import Calendar from Outlook.

• All calendar entries are copied into Join Me

• Select the required entries, or select All

• Copy the imported entries from Local to Phone

13.9 Use Join Me to connect to the Internet

You can use the mobile phone as a dial up modem to connect a computer o the internet.

• Make sure the phone is switched on and connected to the computer and Join Me has been

installed.

• The PC Connection on the handset needs to be set to USB

Menu > Settings > Handset > PC Connection > USB

• Double click the Join Me icon on the desktop.

• Select the Internet tab as shown below

• Press Connect to go online

The default APN is Tel st ra .i nt er ne t. Please check with your service provider to confirm the

correct APN if required.

67

13.10 Connect to a Bluetooth Device

Bluetooth is used as a wireless connection for headsets, hands free car kits and computers. Not all

applications or devices are supported. Bluetooth is an open forum and manufacturers choose which

functions to implement.

The handset supports Bluetooth 1.2 with Handsfree, Headset, FTP and DUN profiles.

Consult the other device for compatibility, connection issues and to find the pairing password.

Please follow the process carefully. Connecting to a Bluetooth device first time around requires

authentication where both devices share a password.

When the devices are paired and connected the process is more automatic.

Connect to a Bluetooth Device

Menu > Tool s > Bluetooth > Bluetooth Manager

• Press the Left or Right Arrow Key to switch Bluetooth on.

• Go down to Visible then press the Left or Right Arrow Key to select Show. The phone name can be

customised if required. Press OK to confirm.

• Go to My Devices and press OK. Press Search to look for Bluetooth devices nearby.

• The chosen device must be switched on and in pairing mode.

• Available devices are listed in the device list. Select the required device and press OK to Connect.

• Enter the pass code, usually 0000 or 1234. Consult the device for more information.

• If you are connecting to a PC or another mobile enter the same password when requested on that

device.

• Once the password has been shared and accepted by both devices they are paired.

68

Send files from the handset to another device

Menu > Tool s > File Manager

• Browse through the folders to the chosen file

• Press the Left Soft Key for Options

• Choose Send then select Bluetooth and press the OK Key

• If no devices are shown press Search

• Select the required device to send the file to

• Enter a pass code and use the same pass code on the other device (eg 0000).

Receive files from another device

• When another device sends you a file press Ye s to authorise the connection

• Press Ye s to accept the file

Connect to a Bluetooth Car Kit or Personal Headset

Follow the manufacturer’s instructions carefully to enable Pairing Mode on the other device.

It is not possible to connect the phone to the other device unless Pairing Mode is enabled.

Select the required device, share a pass code and press Connect.

Menu > Tools > Bluetooth > Bluetooth Manager > Turn On, Show > OK

• Make sure Bluetooth is On and in Show mode and the other device is in Pairing Mode

• On the handset go to Bluetooth: Menu > Too ls > Bluetooth > My Devices

• Press the Right Soft Key to Search

• From the list of available devices select the required device and press OK to Connect

• Enter the pass code specified in the user guide of the far end device (eg 0000 or 1234)

• When the devices are paired the handset will report the device has been added

69

• In My Devices go to the new device and press OK to Connect

• The devices are now Connected

• When connected, incoming calls are sent to the Bluetooth device automatically. Press the call

button to answer.

• During a call press Options > Switch to Handset to return the call to the handset

13.11 Dial Up Networking using USB or Bluetooth

Dial Up Networking (DUN) is a method to connect your PC or MAC to the internet using the handset as

a modem.

1.Dial up Networking over USB using the Windows Wizard

Make sure Join Me is installed, the handset is on and connected to the PC using the USB lead supplied.

Example for Windows XP

On the PC go Start > Accessories > Communications > New Connection Wizard and follow the prompts:

Connect to the internet > Set up my connection manually > Connect using a dial up modem

Select the ZTE USB Modem and uncheck any other modems

The ISP Name can be any name you like eg. T165i Handset

Set the Phone number to *99# > The Username and Password must be blank >

‘Make this the default Internet connection’ can be unchecked (optional) >

‘Add a shortcut to this connection to my Desktop’ can be checked (optional) > Finish

Press Dial to test the connection

The PC will open an internet connection using the handset as a high speed modem

70

2. Dial Up Networking over Bluetooth

Bluetooth can be considered as a wireless replacement for the USB connection and is compatible with

any DUN enabled Bluetooth device. Use Bluetooth to connect the handset to a PC or MAC and use Dial

Up Networking to create an internet connection.

a) Both devices must have Bluetooth ON

Handset: Menu > Tools > Bluetooth > Bluetooth Manager > Turn On, Show > OK

PC or MAC: Enable Bluetooth using the appropriate hardware or software settings

b) Set the handset PC Connection to Bluetooth

Menu > Settings > Handset > PC Connection > Bluetooth

c) Create a New Connection on the PC or MAC

Launch the Bluetooth manager software on your PC or MAC. This varies depending on your platform,

hardware and software. Create a new connection and enter the same password, when prompted, on

each device. Select the T165i Handset, the Dial Number is *99# and the Username and Passwords are

blank.

When the Bluetooth manager opens a connection to the handset, accept the incoming connection by

pressing Yes when prompted.

The PC or MAC can now connect to the internet via the handset.

The features described are dependant on external suppliers’ hardware and software and vary between

platforms and components. Consult your system supplier for more information.

71

13.12 PC Connection

Menu > Settings > Handset > PC Connection > Bluetooth

PC Connection specifies how the handset initiates data connections to the PC. It can be set to be via

Bluetooth or via the USB cable. Join Me requires the USB connector, other transfers can operate via

Bluetooth if supported by your system.

If PC Connection > Bluetooth is selected then Join Me will not connect to the handset.

Restore the PC Connection to USB to re-enable Join Me.

13.13 Synchronize with a network server (SyncML)

Use SyncML to enhance your Personal Information Management by synchronizing Contacts and

Calendar information on the handset with those on a network server.

Menu > Tools > SyncML

• Complete the Sync settings before synchronizing the contacts and calendar

• Select to use Two-way fast sync or Two-way slow sync

• Use Query log to view the SyncML info

• SyncML requires network support and may require an additional subscription

• Contact your Service Provider for more details.

72

14 Other Facilities

14.1 Browser

Menu > Tool s > Browser

Home the home page is set by your Service Provider

New Link enter a web address manually using the keypad

Bookmark Link to a previously saved page

History Display pages visited

Saved Page View a local copy of a previously saved page

Settings Display browser settings (see below)

Version Display current browser version

Menu > Tool s > Browser> Settings > Advanced Settings

Connection settings Sets the APN, preset by your service provider

Advanced settings Customise the browser display modes, sound, cache, cookies etc

Clear cache Clears all cache data

Clear Cookies Deletes all cookie information

Clear autofill list Deletes all input history items

Certificate List the root and CA certificates on the handset

73

14.2 Stopwatch

Menu > Tools > Stopwatch

• Press OK Key to Start timing.

• Press OK to Stop timing. The screen will display the event time.

• Press OK to continue timing.

• Press Right Soft Key to reset.

14.3 Calculator

Menu > Tools > Calculator

• Press 0~9 keys to enter numbers, Decimal to enter the decimal point.

• Press ▲▼▲▼ for +, –, ×, ÷

• Press the End key to clear last digit and results.

• Press OK to show the result

14.4 World Time

Menu > Tools > World Time

• The world time function provides time information on major cities worldwide.

• Scroll to the desired city by using the Left / Right keys.

• Select the required city then press the OK Key to save the selected city as the local time zone.

• Note changing time zones changes the current time setting.

74

14.5 Currency Conversion

Menu > Tools > Currency Conversion

• Convert currencies quickly and easily

• The exchange rate stays set after you close the function

• Use the ▲▼arrows to highlight the required field

• Press Decimal to use a decimal point

• The result is displayed in local or foreign currency automatically

14.6 PocketNews

Menu > Tools > Pocket News

Select the required feature from the available menus. The information is regularly updated by your

service provider and is be sent to your handset by SMS.

14.7 Games and Applications

Menu > Games and Applications

• Download the latest games from your service provider or other specialist websites

• Note that DRM Protected files (Games, Music and Images) cannot be copied to other devices

• The handset supports Java Midlet 2.0

• Use Join Me to copy other games from your computer (see Connectivity)

• Games and applications are saved into the Others folder

• Select Open to install the game.

75

14.8 Voice Recorder

Menu > Multimedia > Voice Recorder

• Press OK to Start recording the voice memo

• Press OK to Pause / Continue (Contin.) recording

• Press the Right Soft Key to Stop recording

• Press OK to Save. The file will be saved to My Audios

• Press Right Soft Key to Discard the voice memo

• Press Left Soft Key to Send the memo via MMS, Email or Bluetooth.

14.9 Slide Show

Menu > Multimedia > Slide Show

• Add pictures by pressing Add or Options > New Slide

• Browse to My Pictures and Mark the pictures you want. Press OK to finish, Play to play.

• Use Options to Edit, create New slide, Rename, Delete, Delete all, and View the image info.

14.10 Streaming URL

Menu > Multimedia > Streaming URL

Streaming URL are links to audio or video streaming content over the internet. The content is only

available while connected to the server and depends on your network provider.

14.11 Connections

Menu > Settings > Handset > Connections

Connections are pre-defined by your service provider and enable the handset to connect to the

internet via WAP and to send multi media messages (MMS). When using an alternate carrier, Add a

new Connection setting as defined by your service provider.

76

14.12 Access Point Settings

Menu > Settings > Handset > Access point settings

Access Point Settings (also called APN) are pre-defined by your service provider and enable the

handset to connect to the internet via WAP and to send multi media messages (MMS). When using an

alternate carrier, Add a new Connection setting as defined by your service provider.

14.13 Restore default settings

Menu > Settings > tab right to Handset Settings > Restore Default Settings > 0000

If the handset is not working as normal, restore the handset to default factory settings. The default

Handset Lock Code is 0000. User content will not be erased.

14.14 Auto Keylock

Menu > Settings > Handset > Keylock

Auto keylock can be set to automatically lock the keypad after a predetermined time. Set your desired
time from the available choices. Press * followed by the Right Soft Key to lock or unlock the keypad.

Emergency numbers can still be dialled while the keypad is in the locked state.

Enter the emergency number on the keypad then press the green Call Key.

77

14.15 Download Location

Menu > Settings > Handset > Download Location

When a microSD card is installed the default save location for user photos and videos changes to the

External Memory. This refers to the microSD card.

14.16 Network Settings

Menu > Settings > tab right to Handset Settings > Network Settings

Preferred mode: Lock the handset to GSM or UMTS (3G) Networks

Preferred Band: Lock the handset to certain bands, U = UMTS, G = GSM

Preferred selection: Choose which network to register with from a list of available networks.

Manual Network Selection overrides the Preferred Mode and Band settings.

The handset will stay on the chosen network and related band. Eg. If you choose a GSM

Network, the Preferred Mode will switch to GSM and remain in GSM-only mode. Further

searches performed by Preferred Selection > Manual mode will only detect networks from the

GSM band. To return to normal mode set Preferred Mode and Preferred band to Automatic.

78

14.17 CTM

Menu > Settings > tab right to Handset > CTM

CTM (Cellular Text Telephone Modem) is a text based communications protocol to offer support to

hearing and speech impaired people. Hearing or speech impaired persons can communicate using a

teletype (TTY) terminal connected to the mobile phone via a CTM Modem. The TTY signals are sent

alongside speech so it is possible to configure the system to enable speaking and hearing as well as

typing or receiving text to the TTY device. See below for the options available:

CTM Mode Description

Full Text entered on the terminal is sent to the other party. Received text from the

other party is displayed on the terminal.

Talk & Read Received text is displayed on the terminal, Voice is relayed to the other party.

Write & Hear Text entered on the terminal is sent to the other party with incoming speech

heard from the other party.

Off All CTM is disabled, use the phone as normal.

• If you are using a TTY terminal the terminal baud rate must be set to 45.45 bps

• If you are using a termina with a built in CTM modem then select CTM Off on the handset

79

15 Technical, Support and Warranty Information

15.1 Troubleshooting and FAQ’s

Please check the manual thoroughly before contacting your service provider

Symptom Solution

No incoming ring

or alarm tone

Check the ring tone and ring volume settings under Profiles

Check the handset is not muted (Long press the # Key)

(No) keytones when

pressing keys

Check the key tone settings in the current profile.

See 7.1 Change the Profiles

A phone number cannot

be dialled

Check for network coverage

Check whether any call restrictions are set. See Call Barring

Short messages cannot be

sent or received

See Text Message Settings and check the SMS centre number is

correct. Contact your service provider for more details.

MMS messages cannot be

sent or received

Your subscription does not include data services. Check with your

service provider.

How do I switch off

Predictive Text?

The # key is used to toggle between different modes.

See Chapter 6 for details.

I cannot connect to

FOXTEL or BigPond

Your subscription is not provisioned for data services. Check with

your service provider.

I cannot connect to

Join Me

Check: Menu > Settings > Handset > PC Connection > USB

Uninstall and re-install the CD software

See FAQ’s at www.zte.com.au for more assistance

80

Symptom Resolution

My phone is slow to

respond, handset storage

problems

Restart your phone every day to refresh the memory

Delete or archive old SMS messages and other content

Restore default settings:

Menu > Settings > Handset > Restore Default > 0000 > Ye s

The battery discharges

quickly

Possible network coverage issue. Check the signal strength. With

only 1 or 2 bars, the battery has to work harder to maintain

network contact. Limit multi-media and Bluetooth usage to save

power. The battery may be worn out and needs to be replaced.

I cannot charge the phone

Confirm the charger is properly inserted. Remove the battery, clean

the contacts using a dry cloth, and check it is inserted correctly. The

battery may be worn out and needs to be replaced.

Tip: Charge the phone using the supplied USB cable.

How do I enter text in an

SMS?

From the phone number field press the down arrow twice to move

into the text area. Use predictive text or abc mode to manually

type words. See chapter 6 for details.

How do I change the

Ringtone?

Edit the current profile and select a new tune from the Audios

directory. See chapter 7 for details.

The handset switches off

after charging.

The handset is charging in the off state. Press and hold the Red key

to switch the handset ON or charge it in the ON state

The handset switches on

automatically

An alarm or calendar event will switch the handset on

automatically.

81

Symptom Resolution

My phone is not able to

connect to other Bluetooth

devices

Turn Bluetooth on. Set visibility to Show. Possible compatibility

issues. Manufacturers incorporate different Bluetooth profiles. Not

all functionality is supported.

How do I transfer pictures

via Bluetooth to a photo

printer (eg Kodak)?

This is not supported due to different Bluetooth profiles. Copy

photos using Join Me or a T-Flash card

15.2 Error Messages

Message Solution

No (U)SIM detected

Check a valid USIM card is inserted

See 2.1 How do I insert the USIM Card?

Enter PIN code Enter the correct PIN code supplied by your service provider

Enter PUK code Contact your service provider to get the PUK code

Enter 16 digit unlock code Please contact your service provider

Enter handset lock code The default handset lock code is 0000

82

15.3 Technical Parameters

Network

Compatibility

3G WCDMA 850, 1900, 2100 MHz with HSDPA data up to 7.2 Mbps

2G GSM 850, 900, 1800, 1900MHz with EDGE data up to 236.8Kpbs

Dimensions L×W×H Approx 117mm x 51mm x 16mm

Weight Approx 119g (Including standard battery)

Features MP4 video, MP3 audio, 2.0/0.3MPixel camera, Video Phone, USB, FM

Radio, A-GPS, Java MIDP 2.0, 2.0” 262K colour LCD display, 240 x 320

pixels, MMS, E-mail, Calendar, Speakerphone, Voice Recorder, Bluetooth

1.2 Stereo, Supports 4GB microSDHC, CTM.

Battery 1300mA hours, Lithium ion (Li-ion)

Continuous idle

time*

Up to 250 hours

Continuous talk

time*

180 minutes on GSM network, 180 minutes on WCDMA network,

Video call >70 minutes

Charge time Approximately 3 hours

Battery Life Approximately 400 charge cycles

Supported Files JPG, BMP, GIF, MP3, WAV, MID, WMA, MMF, AMR, MP4, 3GP, TXT

*The phone’s talk and idle time are based on ideal working environments. The use of extended

backlighting, browser, and network conditions can reduce battery life and talk/idle time.

83

15.4 Support Information

• For Warranty Service directions please consult the ZTE website at http://www.zte.com.au

• All calls for PIN number enquiries, Network problems, Next G Services, BigPond account information,

Web Access, Account and Billing Information, USIM card registration and general enquiries should

be directed to your Service Provider.

15.5 Warranty Information

The warranty does not apply to defects or errors in the product caused by:

(a) Reasonable abrasion.

(b) Misuse including mishandling, physical damage, improper installation, unauthorized

disassembly of the product.

(c) Water, exposure to solvents or any other liquid damage.

(d) Any unauthorized repair or modification.

(e) Power surges, lightning damage, fire, flood or other events outside ZTE’s reasonable control.

(f) Use of the product with any unauthorized third party products such as generic chargers.

(g) Any other cause beyond the range of normal usage for products.

The End User shall have no right to reject, return, or receive a refund for any product from ZTE under

the above-mentioned situations.

Note: Consult the warranty card for full information

84

16 Environmental Statement

The ZTE handset is made using the latest manufacturing techniques and environmental standards to

reduce waste and hazards to the environment. However at the end of life of the equipment the

manufacturer recommends that you return the handset and accessories to the nearest re-cycling

depot or send it to our recycling agent below. Valuable materials such as gold, silver, and copper can

be recovered from the handset. Any toxic materials will be prevented from entering the environment

and the waste materials will be recycled.

At the end of life of the equipment please send the handset, batteries and charger to:

MRI (Australia) Pty Ltd or MRI Sydney

20-24 Dennis St 1 – 4 Bentley Street

Campbellfield Wetherill Park

VIC 3061 NSW 2164

www.mri.com.au

MRI Australia recycles every part of the equipment and diverts over 90% of the materials from landfill

for re-use.

85

17 General Safety and Maintenance Information

The handset contains delicate electronic circuitry, magnets and battery systems. You should treat it

with care and pay attention to the following points:

• Handle the handset with care. Do not drop or

throw the handset down roughly.

• Do not immerse in any liquid. The handset

contains a liquid detection sticker and the
warranty will be voided by any liquid
damage.

• Do not place the handset near computer

disks, credit cards, and other magnetic media.
The information contained on disks or cards
may be erased or damaged.

• Do not leave the handset or battery in direct

sunlight or near other heat sources where
temperatures could exceed 45°C.

• Keep the handset, battery, charger and other

accessories away from children.

• In the unlikely event of a battery leak avoid

contact with your eyes or skin. Flush with
water and consult a doctor.

• Observe and obey warning signs at petrol

stations, airports and hospitals.

• The operation of some medical electronic

devices, such as hearing aids and pacemakers,

may be affected by the handset.

• Take care not to allow metal objects such as

coins or keys to come into contact with the
battery terminals.

• Do not dispose of batteries in a fire.

• Do not throw used batteries into household

rubbish, return them to a recycling point.

• Do not connect the handset to any other

chargers or cigarette lighter chargers.

• Only use the supplied charger.

• Be careful not to pierce the battery with

sharp objects and do not use damaged
batteries.

• Do not disassemble or modify the battery.

• Stop using the battery if abnormal heat,

odour, discolouration, deformation, or
abnormal condition is detected during use,
charge, or storage.

• Do not put the battery in your mouth.

• Only use original replacement batteries.

• Do not attempt to dismantle the handset or

any of its accessories.

86

• Do not place the handset close to the edge of

a table in case it moves when set on vibrate
mode.

• Do not put the handset into a microwave

oven, dryer, or high-pressure container.

• Don’t use the handset immediately after a

sudden temperature change eg. from an air
conditioned environment to high
temperature and humidity outside. In such
cases there could be condensing moisture
inside the handset which can cause internal
damage. Switch off and leave for 30 minutes
before use.

• Do not use the handset while driving or

operating other machinery.

• Do not use the handset where blasting is in

progress.

• Switch the phone off when boarding aircraft.

• Do not leave the handset at the bottom of a

bag where it may be damaged by sharp
objects.

• Do not use your phone or accessories at

refuelling points, near fuel or chemicals or
store it in the same compartment as

flammable gas, liquid or explosives.

• At high volume, prolonged listening to audio

devices can cause hearing loss.

• Do not leave the handset discharged or

disconnected for a long time, otherwise your
personal data may be lost.

• Remember to make backup copies of all

important data on the handset.

• Take care when the phone is in your pocket.

Sitting down may damage the handset.

• It is normal for the handset to become warm

while the battery is being charged.

• Under poor network conditions battery life is

considerably reduced.

• When the battery is thrown away cover the

terminals with insulating tape.

• Please recycle the packaging and all parts.

• Emergency service coverage is dependant on

network availability and battery status.

• It is always good practice to switch off the

handset regularly.

• Do not expose the handset to oils or solvents.

• If you have an alarm set the handset will

switch on at the prescribed time.

87

Index

Advanced Call Settings 32

Answer a Call 21, 29

Appointments 49

Background Screen 42

Backlight Duration 44

Battery 18, 20

Bluetooth 67, 68

Bluetooth Car Kit 68

Calculator 73

Calendar 50

Call Divert 32

Call History 27

Call options 28, 30

Camera 51

CD 58

Change PIN Numbers 45

Charger 19

Charging 20

Contacts 23, 25

Copy photos 60

CTM Set 78

Dial Up Networking (DUN) 69

Dictionary 36

Download Location 47, 77

DTMF 28

E-Mail 39

Emergency Calls 31

En 35

Environmental 84

FAQ’s 79

File Manager 46

FM radio 54

Handsfree 28

International Dialling 28

Java Games 74

Join Me 57, 58

Key Tones 43

Last Number Redial 27

Main Menu 22

Make a Call 21

Make a Voice Call 27

Make Videos 52

Meeting Mode 43

Microsoft Outlook 65

88

MP3 Player 54

Multimedia Message 38

Music Player 54

My Words 37

Network Settings 77

PC 58, 61

PIN Codes 45

Playlist 55

Predictive Text 36

Preferred mode 77

Preferred selection 77

Profiles 41

Push Messages 39

Receive a Text Message 35

Restore default settings 76

RF Energy 3

RF Safety Information 3

Ringtone 43

Safety Information 85

Screen Brightness 44

Send a Text Message 21, 35

Set Alarms 49

Set the Time 20

Shortcut 42

Silent Mode 43

SIM card 17

Slide Show 75

SMS Message Length 37

Snooze 49

Speakerphone 28

Speed Dial 25

Stopwatch 73

Streaming URL 71

SyncML 71

Take Pictures 51

Technical Parameters 82

Troubleshooting 79

USB 19

Using T-Flash cards 47

Vibrate Mode 43

Video Call 29

Voice Recorder 75

Wallpaper 42

WAP 39

Warranty 83

World Time 73