Telkonet SS6600 User Manual
EcoSmart VRF Controller
Firmware Version 2.x
Installation, Operation & Maintenance Guide
Use this guide along with the EcoAir or EcoTouch+ IOM as applicable.
EcoSmart VRF Controller: Part of the EcoWave Remote Thermostat/Controller Package ............................ 5
EcoSmart VRF Controller Required Equipment ............................................................................... 9
EcoSmart VRF Controller Installation .......................................................................................... 9
ZigBee Wireless ................................................................................................................... 14
Regular Maintenance ............................................................................................................ 14
Troubleshooting .................................................................................................................. 16
Appendix A-Anatomy of EcoSource VRF Conroller .......................................................................... 18
Appendix B-Additional Installation Options .................................................................................. 19
NTC Probe ...................................................................................................................... 19
Analog Outputs ................................................................................................................ 19
Proportional Valve Control ................................................................................................... 19
CAUTION!
Failure to understand and follow all instructions carefully before installing or operating this
device could cause personal injury and/or property damage.
All wiring must conform to local and national electrical ordinances and codes.
Prevent electrical shock, personal injury, and equipment damage: prior to installation or
service, disconnect system’s electric power at main fuse or circuit breaker box.
EcoSmart VRF Controller
For Use with Firmware Version 2.x
I, O & M Guide
Revision 2.3
Page 2 www.telkonet.com
Telkonet, Inc.
20800 Swenson Drive, Suite 175
Waukesha, WI 53186
(800) 380-9640
The EcoSmart Energy Management
System
The EcoSmart Energy Management System reduces HVAC
energy consumption without interfering with occupant
comfort.
EcoSmart thermostats such as the EcoAir/EcoTouch
automatically learn and adapt to the heating and cooling
patterns of each room. For example, a room on the east
side of a building will receive direct sunlight in the
morning and will either need less HVAC heating or more
HVAC cooling. However, as the day progresses, the room
will need more HVAC heating or less HVAC cooling as it
moves into the shade. An EcoSmart thermostat will
continually monitor the room, learn its patterns, and
adjust its heating and cooling profiles accordingly.
EcoSmart thermostats also learn and adapt to occupant
schedules. When a room is unoccupied, the
EcoAir/EcoTouch will enter an energy saving mode,
allowing the room to drift away from the desired set
point. During this drift period, the thermostat will
operate the HVAC unit less often, reducing energy costs.
When the room becomes occupied again, the
RecoveryTime™ technology built into each
EcoAir/EcoTouch will return the room to the set point
without occupant interaction.
The EcoWave is available in several configurations to
address specific requirements of multiple applications
including hotel, classroom, office, university dormitory,
military residence hall, retail, public area, convention
center, and a wide variety of commercial and industrial
spaces.
The firmware of standalone EcoWave thermostats is
identical to the firmware of networked versions.
Standalone Thermostats can be networked by adding a
network module to the base units at any time.
Programming features used during installation,
maintenance, and troubleshooting are available in the
on-screen Maintenance Menu.
Regulatory Compliance & FCC Notice
Warning: Any changes or modifications made to this
product not expressly authorized by the manufacturer
could void the user’s right to operate this device.
The device complies with part 15 of the FCC Rules as
well as Industry Canada Rules and Regulations licenseexempt RSS standard(s). Operation is subject to the
following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept
any interference received, including interference that
may cause undesired operation.
Le présent appareil est conforme aux CNR d'Industrie
Canada applicables aux appareils radio exempts de
licence. L'exploitation est autorisée aux deux conditions
suivantes : (1) l'appareil ne doit pas produire de
brouillage, et (2) l'utilisateur de l'appareil doit accepter
tout brouillage radioélectrique subi, même si le
brouillage est susceptible d'en compromettre le
fonctionnement.
A separation distance of at least 20 centimeters should
be maintained between the transmitter's radiating
structure(s) and the body of the user or nearby persons.
Afin de se conformer aux exigences d'exposition RF MIC /
FCC / ISED, cet appareil doit être installé pour fournir au
moins 20 cm de séparation du corps humain en tout
temps.
FCC ID: XV6SS6600
EcoWave Remote Thermostat/Controller
Package
The EcoWave Remote Thermostat/Controller Package is
comprised of two hardware components: the wireless
EcoAir/EcoTouch battery powered display unit and the
EcoSource+ HVAC controller. The EcoSource+ is placed in
the HVAC unit for physical control of the system. The
EcoAir/EcoTouch display can be placed in the optimum
location for both temperature measurement and ease of
occupant use. There are no restrictions based on where
existing thermostat wire has been run or if there are
enough conductors.
The EcoWave Package can be configured for many
different HVAC scenarios. It can control multiple HVAC
systems, each equipped with an EcoSource+, but all
directed by a single EcoAir/EcoTouch display unit. This
type of installation reduces the complexity of running
multiple HVAC units in a single large space and
eliminating the potential of opposing modes forcing
equipment to compete against each other.
The EcoSource+ can accept associations with up to 15
total EcoSmart and other compatible wireless devices,
such as multiple occupancy sensors and door switches.
Each compatible wireless device may be associated to
more than one EcoSource+.
The EcoWave adds functionality, increased usability,
extra efficiency, and component cost savings to
conference rooms or large room suites. Multiple
EcoSmart VRF Controller
For Use with Firmware Version 2.x
I, O & M Guide
Revision 2.3
Page 3
20800 Swenson Drive, Suite 175
Waukesha, WI 53186
www.telkonet.com
Telkonet, Inc.
(800) 380-9640
EcoAir/EcoTouch thermostats in different areas of a
building give each individual area the ability to make
setpoint changes to control a single EcoSource+.
Together, the EcoWave package forms a wireless
programmable controllable thermostat with over 125
configurable settings used to control the efficiency of
HVAC systems. It can be easily installed on packaged
terminal air conditioners, fan coils, heat pumps, split
systems, and more. With software-based relay control
and fan speed configuration, programming setup is
simple and fast.
Wiring follows industry-standard conventions whenever
possible. Telkonet can develop specific wiring diagrams,
if a complete specification is provided for the HVAC
unit(s) in use at the site. The pin allocations of the
EcoSource+ are below. The wiring interface conforms to
industry standards.
Functional Caveats
Telkonet ships equipment to customers pre-programmed
based on a pre-deployment analysis and discussion with
property management. Generally, command-level
programming at the field level will not be needed. When
a command change is needed, Telkonet will provide a
detailed synopsis of the proposed changes. Arbitrarily
changing command values without prior discussion with
Telkonet Applications Engineering can result in
suboptimal thermostat performance and a loss of energy
savings. All of these can possibly impact the user
interface. For this reason, such arbitrary changes do not
represent a Recommended Best Practice, and any
corrective actions taken by Telkonet (including
consultation) are subject to Professional Services charges
at prevailing rate.
EcoSmart VRF Controller
For Use with Firmware Version 2.x
I, O & M Guide
Revision 2.3
Page 4
20800 Swenson Drive, Suite 175
Waukesha, WI 53186
www.telkonet.com
Telkonet, Inc.
(800) 380-9640
EcoSmart VRF Controller: Part of the EcoWave Remote
Thermostat/Controller Package
EcoSmart VRF Controller: Part of the EcoWave Remote Thermostat/Controller Package
The EcoWave package is comprised of two hardware components as shown below. Together they form a
wireless programmable controllable thermostat. With software-based relay control and fan speed
configuration, programming setup is simple and fast.
Display unit
EcoTouch+ (or EcoAir)
EcoSmart VRF Controller
Place in optimum location for occupancy detection,
temperature measurement and ease of occupant use
HVAC Controller
Install in or on HVAC unit
Accepts association with 15 total compatible wireless devices
Each compatible wireless device can be associated to
multiple EcoSmart VRF Controllers
Accomodates a Variety of Configurations
The EcoWave Package can be configured for many different HVAC scenarios. For example:
One EcoTouch+ (or EcoAir) can
control multiple HVAC systems,
each equipped with an EcoSource
VRF, but all directed by a single
EcoTouch+ (or EcoAir) display
unit. This type of installation
reduces the complexity of running
multiple HVAC units in a single
large space and eliminating the
potential of opposing modes
forcing equipment to compete
against each other.
.
EcoSmart VRF Controller
For Use with Firmware Version 2.x
EcoSmart VRF Controller: Part of the EcoWave
Remote Thermostat/Controller Package
I, O & M Guide
Revision 2.3
Page 5
20800 Swenson Drive, Suite 175
Waukesha, WI 53186
www.telkonet.com
Telkonet, Inc.
(800) 380-9640
EcoSmart VRF Controller: Part of the EcoWave Remote
Thermostat/Controller Package
Multiple EcoTouch+ (or EcoAirs) can
control one HVAC system, equipped with
one EcoSource VRF.
The wiring interface conforms to industry standards. Telkonet can develop specific wiring diagrams, if a
complete specification is provided for the HVAC unit(s) in use at the site.
EcoSmart VRF Controller
For Use with Firmware Version 2.x
EcoSmart VRF Controller: Part of the EcoWave
Remote Thermostat/Controller Package
I, O & M Guide
Revision 2.3
Page 6
20800 Swenson Drive, Suite 175
Waukesha, WI 53186
www.telkonet.com
Telkonet, Inc.
(800) 380-9640
Loading...