Teli CS3920 Operation Manual

Version 1.3

High-resolution CCD Camera

Model CS3920

Operation Manual

Enter the blank below Product Serial Number, which is found on bottom/rear
chassis of your camera. Keep this number for your record.

Model No.

CS3920

Serial No.

TOKYO ELECTRONIC INDUSTRY CO., LTD.

2000-04-07

Thank you for purchasing our CS3920 B/W CCD camera.
This operation manual contains some important information such as how to use
this equipment correctly and safely. Please read through this manual carefully.
After reading, keep this manual by the side of your equipment for your future
reference.

CONTENTS

GENERAL SAFETY INSTRUCTIONS

1. PRODUCT DESCRIPTION 1

2. FEATURES 1

3. CONFIGURATION 1

4. OPTIONAL ACCESSORIES 1

5. DESIGNATIONS AND WORKINGS OF EACH PART

2

6. HOW TO MOUNT THE CAMERA 3

7. CONNECTION 3

8. SETTING 4

9. SPECIFICATIONS 6

10. TIMING CHART 7

11. EXTERNAL-VIEW DRAWING 13

BEFORE USING THE CAMERA ― GENERAL SAFETY INSTRUCTIONS

This Operation manual contains important information for the operator (user) and/or people
around him/her to avoid personal injuries, or property damages against him/her or people
around him/her by using this product correctly. Prior to use, read this operation manual
carefully to fully understand its instructions for correct use.

[Definition of markings]
The meaning of each mark used in this instruction manual is given below.

DANGER

This mark warns the user that improper use, indicated with this mark, may
cause death or severe personal injuries against the user or people around
him/her.

CAUTION

This mark warns the user that improper use, indicated with this mark, may
cause personal injuries (*1) or material damages (*2) against the user or

people around him/her.
Notes
*1 : Personal injuries mean wounds, burns, electric shocks, and others for which the person
injured need not to be hospitalized nor to be cared for the long term.
*2 : Material damages mean any direct or consequential damages related to property or material
loss.

This mark indicates what the user SHOULD NOT DO. The details of things which the user
should not do are described next to this mark.
This mark indicates what the user MUST DO. The details of things which the user must do
are described next to this mark.
This mark indicates that the user must be alert against a possible DANGER. The details of
the DANGER which the user must be aware of are described next to this mark.
This mark indicates that the user are given a CAUTION against possible hazards. The
details of the CAUTION which the user must be aware of are described next to this mark.

●Handling precautions

DANGER

If any overheating sign is observed, discontinue the use immediately.
In the event that smoke, smell, or any other overheating sign is observed, turn the power
switch of the system OFF immediately, and remove the camera cable from the camera
connector. Do NOT try to continue to use the camera. To do so in spite of clear signs of
malfunction invites a fire, an electric shock hazard, or a serious damage to the camera. In
such case, contact us or our dealer/distributor from which you purchased the camera for
repair service.
If any malfunctioning sign is observed, discontinue the use immediately.
Do NOT try to use the camera when it is malfunctioning. (Ex. No images on the
monitor) In the event of malfunction, turn the power switch of the system OFF
immediately, and remove the camera cable from the camera connector. In such case,
contact us or our dealer/distributor from which you purchased the camera for repair
service.

!

!

!

If any foreign object gets into the camera, discontinue the use immediately.
In the event that liquids, small particles, or any other foreign objects get into the camera,
do NOT try to continue to use the camera. To do so invites a fire or an electric shock
hazard. In that case, turn the power switch of the camera OFF immediately, and remove
the camera cable from the camera connector. After that, contact us or our
dealer/distributor from which you purchased the camera for repair service/technical
advice.
If any outer strong impact is given to the camera, discontinue the use immediately.
In the event that the camera is dropped onto the ground, or the cabinet of the camera is
damaged, turn the power switch of the system OFF immediately, and remove the camera
cable from the camera connector. Do NOT try to continue to use the camera. To do so
invites a fire or an electric shock hazard. In such case, contact us or our
dealer/distributor from which you purchased the camera for repair service.
Do NOT disassemble the camera.
Do NOT attempt to pull apart, repair, or modify the camera on your own. To do so might
lead to an irreparable breakdown / malfunction, or might invite an unexpected accident.
Contact us or the dealer/distributor from which you purchased the camera for
repair/modification.
Do NOT supply any power other than specified.
The camera is designed to work only under specified voltage. Do NOT attempt to drive
the camera with the power other than DC12V. Operating the camera under power other
than DC12V invites a fire or a electric shock hazard.
Do NOT place the camera unstably.
Do NOT place the system on an unstable table, sloped ground, etc.. Make sure that the
camera do not fall to prevent an accident.
Do NOT place any potentially-hazardous things on the camera.
Do NOT place any things on the camera which may, if it gets into the inside of the body,
damage the inner parts of the camera (such as a flower pot, glass, cosmetics, a container
filled with liquids or chemicals, as well as small metal parts, etc.). If tumbled, the liquids
inside the bottle, etc. may get into the system, causing a fire or an electric shock
accident.
Do NOT short-circuit signal outputs.
Avoid short-circuit of signal outputs. Otherwise it may cause damage to the camera. For
inspection of inner parts/circuits, adjustment, maintenance, contact us or the
dealer/distributor from which you purchased the camera.
Do NOT use the camera in a high-humidity environment.
Do NOT place the camera near a humidifier, or in other high-humidity environment.
To do so may cause a fire or an electric shock accident.
Do NOT expose the camera to direct sunlight, nor intensive heat.
Do not place the camera where it is exposed to direct sunlight, or in a higher temperature
than guaranteed (Over 40 degrees Celsius). To do so may cause the inner temperature of
the camera to go up, resulting in burning-down of inner parts, circuits or a fire accident.
Do NOT expose the camera to greasy fumes
Do NOT place the camera at the location where it is exposed to greasy fumes or steams,
or heavy dusts. To do so may cause the inner temperature of the camera to go up,
resulting in burning-down of inner parts/circuits or a fire accident.

CAUTION

Do NOT connect/disconnect connectors with power ON.
Before connecting/disconnecting connectors, make sure to check if the system is
powered OFF. Doing so with power ON may cause a damage or an electric shock
accident.
Do NOT give a strong shock/impact against the camera-head.
Avoid giving a strong shock against the camera head. The camera-head might be
damaged.
Do NOT pull/swing the cable forcefully.
Do not pull strongly the camera cable/camera-head nor swing it. The stress from pulling
or swinging may cause damage in the coating of the cable, or breaks in the inside wires.
In carrying the camera around, be sure to disconnect connection cables/lines beforehand.
Otherwise, the connection cable(s)/line(s) might be damaged, causing a fire or an
electric shock accident.

If the camera is operated in the electromagnetic field, there may be cases where beat
noises (vertical, horizontal, or oblique stripes) may appear in the video output. In that
case, take preventive measures on the electromagnetic-wave generating source so that
the camera do not receive the interference by the electromagnetic-wave. Take extra
precautions against electromagnetic-wave-interference if the camera is used with a
servomotor, inverter, or other electromagnetic-wave-generating equipment.
When the camera is not in use, put a lens or a lens-cap onto the camera head so that the
image pickup plane of CCD is protected from dust, foreign object, or other flaw-causing
object. If the glass plane (image pickup plane) gets dirty, clean it with a cotton swab.
When it needs to be cleaned with a cleaner, be sure NOT to use any organic solvent other
than ethyl alcohol. As a countermeasure against condensation, when the camera is
moved from a warm place to a cold place, take appropriate precautions to prevent
condensation from forming on the camera.
Avoid placing the camera where it is splashed with water or any other fluids. Operating
the camera with its inner parts/circuits in wet condition may cause a damage or an
electric shock accident.

!

!

!

!

!

RESTRICTION FOR USE

Do not attempt irregular signal interface other than specified. Under signal interface
other than recommended/specified in this instruction manual, the camera might fail to
exert the maximum performance. In much worse case, if you continue to use the camera
under incorrect signal interface, part(s) of circuits might burn down.
In case malfunction of this equipment (e.g. video output cut-off) can be expected to lead
to significant accident, avoid using this equipment for such system build-in use.

CASES FOR INDEMINITY (LIMITED WARRANTY)

We shall be exempted from taking responsibility and held harmless for damages or
losses incurred by user in the following cases.

1.

In case damages or losses are caused by fire, earthquake, or other acts of Gods, the
act by third party, misuse by the user deliberately or erroneously, use under extreme
operating conditions.

2.

In case indirect, additional, consequential damages (loss of expected interest,
suspension of business activities) are incurred as results of malfunction or
non-function of the equipment, we shall be exempted from assuming responsibility
for such damages.

3.

In case damages or losses are caused by incorrect use which is not in line with the
instructions in this operation manual.

4.

In case damages or losses are caused by malfunction resulting from bad connection
with other equipment.

5.

In case damages or losses are caused by repair or modification done by the user.