Telex BP-2000, BP-1000 User Manual
Telex
Operating Instructions
1
Chan
2
Call
Talk
BP-2000/BP-1000
Belt Packs
®
Audiocom
Intercom
System
GENERAL
The Audiocom® BP-2000 and BP-1000 are microprocessor
controlled one- and two-channel intercom belt packs. An
internal switch and jumper setting allows the units to be used
with Clear-Com® components, if desired. Other internal
switch and jumper settings allow the unit to be uniquely
configured to the operator’s requirements.
FCC STATEMENT
This equipment uses, and can radiate radio frequency energy
that may cause interference to radio communications if not
installed in accordance with this manual. The equipment has
been tested and found to comply with the limits of a Class A
computing device pursuant to Subpart B, Part 15 of FCC
Rules which are designed to provide reasonable protection
against such interference when operated in a commercial
environment. Operation of this equipment in a residential
area may cause interference which the user (at his own
expense) will be required to correct.
This product meets the Electromagnetic Compatibility
Directive, 89/336/EEC.
®Audiocom is a registered trademark of Telex Communications, Inc.,
™Burnsville, Minnesota 55337
®Clear-Com is a registered trademark of Clear-Com Intercom Systems
1
End-User License Agreement for Telex®Software
IMPORTANT - Please read this document carefully before using this
product.
THIS DOCUMENT STATES THE TERMS AND CONDITIONS UPON WHICH
TELEX COMMUNICATIONS, INC. (the ‘COMPANY’) OFFERS TO LICENSE
THE INSTALLED SOFTWARE OR PROGRAM (the ‘SOFTWARE’) FOR USE
WITH THE PRODUCT IN WHICH IT WAS INSTALLED. YOU ARE AGREEING
TO BECOME BOUND BY THE TERMS OF THIS AGREEMENT. IF YOU DO
NOT AGREE TO THE TERMS OF THIS AGREEMENT, DO NOT USE THIS
PRODUCT. PROMPTLY RETURN THE PRODUCT TO THE PLACE WHERE
YOU OBTAINED IT FOR A FULL REFUND.
The installed software as supplied by the Company is licensed, not sold, to you
for use only under the terms of this license, and the Company reserves all rights
not expresslygranted to you. You own the productor other mediaon or inwhich
the Software is originally or subsequently recorded or fixed, but the Company
retains ownership of all copies of the Software itself.
1. License: This license allows you to use the Software for internal purposes
only on a single product in which it was installed.
2. Restrictions: (a) You may not market, distribute or transfer copies of the
Software to others or electronically transferorduplicatetheSoftware. YOU MAY
NOT REVERSE ENGINEER, DECOMPILE, DISASSEMBLE, MODIFY,
ADAPT, TRANSLATE, RENT, LEASE OR LOAN THE SOFTWARE OR
CREATE DERIVATIVE WORKS BASED ON THE SOFTWARE OR ANY
ACCOMPANYING WRITTEN MATERIALS. (b) The Software and the
accompanying written materials are copyrighted. Unauthorized copying of the
Software, including portions thereof or the written materials, is expressly
forbidden. (c) You understand that the Company may update or revise the
Software and in so doing incurs no obligation to furnish such updates to you.
3. Limited Warranty: The Company does not warrant that the operation of the
Software will meet your requirements or operate free from error. The Company
DISCLAIMS ALL OTHER WARRANTIES AND CONDITIONS EITHER
EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
NON-INFRINGEMENT OF THIRD PARTY RIGHTS.
4. Limited Liability: The liability of the Company for any claims arising out ot this
License based upon the Software, regardless of the form of action, shall not
exceed the greater of the license fee for the Software or $50.
38109-709 Rev A 10/97
2
OPERATION
SYSTEM POWER
The BP-2000 belt pack receives power externally, in one of
two ways:
· Via the intercom channel (similar to the BP-1000)
· Via the local-power (pin 2) of the intercom channel
connector
The BP-1000 belt pack receives power externally, via the
intercom channel.
Both the BP-2000 and BP-1000 will pass system power
through to subsequent belt packs that are “daisy chained”
together.
INITIAL BP-2000/BP-1000 SETUP
The channel termination is initially set for balanced operation,
which is compatible with other Audiocom® equipment. If the
unit is going to be connected to Clear-Com equipment, one
switch and several jumpers must be changed as described in
the section on Clear-Com Setup in this manual.
The headset microphone type is initially set for single-ended
dynamic operation. To change the microphone type to
balanced dynamic, refer to Table 2 for the position of J15.
To change the headset microphone to an electret type, refer
to Table 2 in this manual for the position of switch SW1. If the
type requirement of a headset microphone is unknown, the
recommended setting is single-ended dynamic.
3
1 234
BP-2000
BP-1000
1
TALKCALLCHAN
2
5
6
HEADSET LINES
1 34
77
TALKCALL
6
5
88
HEADSET LINES
Figure 1. BP-2000 & BP-1000
Connections and Controls
4
EXTERNAL CONNECTIONS & CONTROLS
NOTE: The numbers refer to the callouts in Figure 1.
1. Volume Control
Use this control to adjust the headset listen level.
2.
Chan
Button and Indicators
The
Chan
button (only on the BP-2000) allows the user to
select which intercom channel is active. The yellow
indicator next to the
channel. Press the
selection, the yellow indicator for that channel will light.
3.
Call
Button and Indicator
The Call function allows the user to send or receive
signals to other devices on the intercom channel selected.
The
Call
button operates in two ways:
Call receive:
When there is an incoming call signal, the indicator is
red. (If Audible Call Alert is enabled, incoming calls will
cause beeps in the headset.) On the BP-2000, calls
can be received on the selected channel only.
1or2
lights to show the active
Chan
button to change the channel
Call send:
To send a call signal to all stations on a channel, press
and hold the
received. The indicator will glow red. On the BP-2000,
calls can be sent on the selected channel only.
4.
Talk
Button and Indicator
The
Talk
button activates the headset microphone and
operates in two ways:
Call
button until a verbal response is
5
Loading...