Page 1
F.01U.307.689 Rev. 02 MAY/2017
Airman 7
Operating Instructions
Page 2
2 Airman 8
Bosch Security Systems, Inc.
Operating Instructions
F.01U.307.689
Rev. 02
PROPRIETARY NOTICE
The product information and design disclosed herein were originated by and are the property of
Bosch Security Systems, Inc. Bosch reserves all patent, proprietary design, manufacturing,
reproduction, use and sales rights thereto, and to any article disclosed therein, except to the
extent rights are expressly granted to others.
COPYRIGHT NOTICE
Copyright 2017 by Bosch Security Systems, Inc. All rights reserved. Reproduction, in whole or
in part, without prior written permission from Bosch is prohibited.
*All other trademarks are property of their respective owners.
WARRANTY AND SERVICE INFORMATION
For warranty and service information................................................... www.telex.com/warranty
CUSTOMER SUPPORT
Technical questions should be directed to:
Customer Service Department
Bosch Security Systems, Inc.
www.telex.com
Technical Solutions
Telex Aviation Technical Support ...................................................................... 1-800-898-6723
After-Sales Support............................................................................................. 1-800-553-5992
DISCLAIMER
The manufacturer of the equipment described herein makes no expressed or implied
warranty with respect to anything contained in this manual and shall not be held liable
for any implied warranties of fitness for a particular application or for any indirect,
special, or consequential damages. The information contained herein is subject to
change without prior notice and shall not be construed as an expressed or implied
commitment on the part of the manufacturer.
Page 3
Airman 8 Important! Read Before Use 3
Bosch Security Systems, Inc.
Operating Instructions
F.01U.307.689
Rev. 02
Important!
Read Before Use
General:
• Read this technical manual completely before using the product.
• This technical manual is also available at www.telex.com/aviation.
Health and Safety:
• Always keep at least 4” (~10cm) between the ear cups and a pacemaker
or implanted defibrillator because this product generates magnetic fields.
• Keep away from children – product parts and accessories are a choking
hazard.
• This headset is capable of producing sound pressure over 85dB(A). In
many countries, this is the maximum legal level for continuous noise
exposure during the working day. Do not listen at high volume levels for
extended periods of time to prevent hearing damage.
Preventing Damage and Malfunctions:
• Always keep the headset dry and do not expose it to extreme
temperatures to avoid corrosion or deformation.
• Never attempt to repair a headset which is not operating correctly.
Contact the Telex dealer you purchased the headset through or
authorized repair facility.
• Only replace parts of the headset whose replacement is described within
this manual. All other parts must be replaced by an authorized repair
facility.
Page 4
4 Important! Read Before Use Airman 8
Bosch Security Systems, Inc.
Operating Instructions
F.01U.307.689
Rev. 02
Page 5
Table
of
Contents
F.01U.307.689
Rev. 02
Operating Instructions
Bosch Security Systems, Inc.
IMPORTANT! READ BEFORE USE ...............................3
INTRODUCTION ..............................................................7
General Description .............................................................. 7
Features ................................................................................ 7
FAA ....................................................................................... 8
Reference View ................................................................... 10
Connections ........................................................................ 11
INSTALLATION .............................................................13
Installation ........................................................................... 13
Headset Adjustment ............................................................ 16
Mic Placement .................................................................... 18
Microphone Gain Adjustment .............................................. 19
Clothing Clip Assembly and Attachment ............................. 20
CARE & MAINTENANCE ..............................................21
Recommended Maintenance Schedule .............................. 21
Cleaning the Headset and Connectors ............................... 22
Cleaning the Ear Cushions and Headband Pads ............... 22
Replacing Ear Cushions and Headband Pads .................... 22
Installing or Replacing the Hygienic Covers ....................... 24
Cleaning or Replacing the Windscreen ............................... 24
Headset Storage ................................................................. 25
TROUBLESHOOTING ...................................................27
Troubleshooting .................................................................. 27
Label Information ................................................................ 32
Page 6
6 Airman 7
F.01U.307.689
Rev. 02
Operating Instructions
Bosch Security Systems, Inc.
SPECIFICATIONS .........................................................33
Specifications ......................................................................33
Part Number Information .....................................................35
Page 7
Bosch Security Systems, Inc.
Operating Instructions
F.01U.307.689
Rev. 02
CHAPTER 1
Introduction
General Description
The Telex Airman 7 is a lightweight aviation headset designed specifically for
optimizing pilot communications in commercial and business turbine aircraft.
Building on the tradition of the Airman 750, the Airman 7 has improved
durability, intelligibility, and comfort. Soft pliable ear cushions and headband
pads combine with dual-direction ear cup pivots to provide long flight wearing
comfort.
Features
• Flexible boom-mounted, noise-reducing microphone, positionable for
right- or left-side use
• Dual, Single, and Listen-only versions available
• Soft, pliable ear cushions and headband pads
• FAA TSO C-139a approved
Page 8
Bosch Security Systems, Inc.
Operating Instructions
F.01U.307.689
Rev. 02
8 Introduction Airman 7
FAA
The Telex Airman 7 Headset (with or without microphone) is approved for
aircraft use under FAA TSO-C139A.
The conditions and tests required for the TSO approval of this article are
minimum performance standards. It is the responsibility of those installing this
article, either on or within a specific type or class of aircraft, to determine that
the aircraft installation conditions are within the TSO standards. TSO articles
may have separate approval for installation on aircraft. The article may be
installed only if performed under 14 CFR part 43 or the applicable air
worthiness requirements.
Tests were conducted per the minimum standards defined in RTCA DO -214A
and DO-160G. The headset was designed and is manufactured to meet the
following environmental categories.
Environmental Qualification Form
CONDITIONS
DO-160G
SECTION
DESCRIPTION OF TESTS
CONDUCTED
Temperature and Altitude 4.0
Ground Survival Low-Temp/Short-Time
Operating Low-Temp
4.5.1 Equipment tested to Category A1
Operating Low Temperature 4.5.2 Equipment tested to Category A1
Ground Survival High-Temp & Short-Time
Operating High-Temp
4.5.3 Equipment tested to Category A1
High Temperature 4.5.4 Equipment tested to Category A1 with
70°C max. exception
by DO-214 2.5.1.2
In-Flight Loss of Cooling 4.5.5 Equipment identified as Category X, N/A
Altitude 4.6.1 Equipment tested to Category A1/
50000ft.
Decompression 4.6.2 Equipment tested to Category A1/
50000ft.
Overpressure 4.6.3 Equipment tested to Category A1
Temperature Variation 5.0 Equipment tested to Category C
Humidity 6.0 Equipment tested to Category A
Operational Shock and Crash Safety 7.0 Equipment identified as Category X, N/A
by DO-214 2.5.4.1 and 2.5.4.2
Vibration 8.0 Equipment tested to Category S, aircraft
zone 2 (instrument panel
or console mounting), Aircraft type 2
(Fixed Wing Turbojet or Turbofan
engines), using vibration test curve B.
Explosive Atmosphere 9.0 Not Applicable
Waterproofness 10.0 Not Applicable
Fluids Susceptibility 11.0 Not Applicable
Sand and Dust 12.0 Not Applicable
Page 9
Bosch Security Systems, Inc.
Operating Instructions
F.01U.307.689
Rev. 02
Airman 7 Introduction 9
Fungus 13.0 Equipment identified as Category X, N/A
Salt Fog Test 14.0 Equipment identified as Category X, N/A
Magnetic Effect 15.0 Equipment is Category Z
Power Input 16.0 Equipment tested to Category A
Voltage Spike 17.0 Equipment tested to Category A
Audio Frequency Susceptibility 18.0 Equipment tested to Category R
Induced Signal Susceptibility 19.0 Equipment tested to Category ZW
Radio Frequency Susceptibility 20.0 Equipment tested to Category T
Momentary Equipment tested to Category T
Steady State Equipment tested to DO-214 2.5.11.2
Emission of RF Energy 21.0 Equipment tested to Category M
Lightning Induced Transient Susceptibility
(multiple burst)
22.0 Equipment identified as Category L2
Lightning Direct Effects 23.0 Not Applicable
Icing 24.0 Not Applicable
Electrostatic Discharge 25.0 Not Applicable
Fire, Flammability 26.0 Not Applicable - all components except
wire considered small parts
Wire Flammability Flammability:
-JAR, FAR 25.853, 25.855, 25.869, and
appendix F
CONDITIONS
DO-160G
SECTION
DESCRIPTION OF TESTS
CONDUCTED
Page 10
Bosch Security Systems, Inc.
Operating Instructions
F.01U.307.689
Rev. 02
10 Introduction Airman 7
Reference View
FIGURE 1. Airman 7 Reference view
1. Headband Pad
2. Headset Slider
3. Ear Cushion
4. Ear Cup Rotator
5. Yok e
6. Boom Rotator
7. Strain Relief
8. Boom
9. Microphone/Windscreen
10. Te mpl e Pa d
Page 11
Bosch Security Systems, Inc.
Operating Instructions
F.01U.307.689
Rev. 02
Airman 7 Introduction 11
Connections
Airman 7 Series headsets are available with multiple connector styles
depending on the application of use. All models utilize custom cables
developed specifically for in-cockpit use. All connection points implement
strain and bend relief features to provide long-term durability. Shielded wires
throughout the headset protect against RFI (Radio Frequency Interference)
and EMI (Electromagnetic Interference).
Dual Plug PJ Connector
PJ-068 (equivalent) Description
Tip Not Used
Ring Mic Signal
Sleeve Mic GND
PJ-055 (equivalent) Description
Tip Headphone Signal
Sleeve Headphone GND
Page 12
Bosch Security Systems, Inc.
Operating Instructions
F.01U.307.689
Rev. 02
12 Introduction Airman 7
Single Plug PJ Connector
5-Pin XLR Aircraft Cable
PJ-068 (equivalent) Description
Tip Headphone Signal
Sleeve Headphone GND
Pin Description Color
1 Headphone Signal Yellow
2 Headphone GND Black/Outer Shield
3 Mic Signal White
4 Mic GND and ANR Return Blue/Inner Shield
5 ANR IN Red
Page 13
Bosch Security Systems, Inc.
Operating Instructions
F.01U.307.689
Rev. 02
CHAPTER 2
Installation
Installation
To install the headset for use, do the following:
Step 1 Inspect the headset for signs of damage. Do not use the
headset if signs of damage are evident.
Step 2 Plug the headset into the aircraft console, see “Install the Sin-
gle Plug Headphone in an Aircraft (Listen Only)” on page 14,
“Install the Dual Plug Headset in an Aircraft” on page 14, or
“Install the XLR Plug Headset in an Aircraft” on page 15.
Step 3 Put the headset on.
Step 4 Adjust the headset for proper use, see “Headset Adjustment”
on page 16.
Step 5 Attach the clothing clip.
Page 14
Bosch Security Systems, Inc.
Operating Instructions
F.01U.307.689
Rev. 02
14 Installation Airman 7
Install the Single Plug Headphone in an Aircraft (Listen Only)
To install the single plug headphone in an aircraft, do the following:
1. Insert the plug into the headset jack on the aircraft console.
Install the Dual Plug Headset in an Aircraft
To install the dual plug headset in an aircraft, do the following:
1. Insert the microphone plug (smaller plug) into the microphone
jack on the aircraft console.
2. Insert the headset plug (larger plug) into the headset jack on the
aircraft console.
FIGURE 1. Single Plug Installation
FIGURE 2. Dual Plug Installation
Page 15
Bosch Security Systems, Inc.
Operating Instructions
F.01U.307.689
Rev. 02
Airman 7 Installation 15
Install the XLR Plug Headset in an Aircraft
To install the XLR plug headset in an aircraft, do the following:
> Insert the XLR plug into the XLR jack on the aircraft audio panel.
FIGURE 3. XLR Plug Installation
Page 16
Bosch Security Systems, Inc.
Operating Instructions
F.01U.307.689
Rev. 02
16 Installation Airman 7
Headset Adjustment
The Airman 7 headset is designed to rest evenly on top of the head with each
ear cup sitting centered and flush on each ear. The headset/headphone
should fit over the head without pinching or gapping.
Headband Adjustment
To adjust the headband size, do the following:
> With the headset resting securely on the top of the head, slide the ear
cup up and down to center the ear cup over the ear.
NOTE: The headset works best when the headband pad is centered on
the head. Both sides of the headset should be slid evenly for
proper use.
FIGURE 4. Headband Adjust
Page 17
Bosch Security Systems, Inc.
Operating Instructions
F.01U.307.689
Rev. 02
Airman 7 Installation 17
Ear Cup Adjustment
To adjust the ear cup to fit correctly, do the following:
> Swivel the ear cup left or right to position the ear cup straight on
the ear.
NOTE: Over time, repositioning the headset may be necessary for
comfort.
IMPORTANT: Take care not to over-adjust the ear cups. Do not rotate
the ear cups more than 90° or damage may occur.
FIGURE 5. Ear Cup Adjustment
Page 18
Bosch Security Systems, Inc.
Operating Instructions
F.01U.307.689
Rev. 02
18 Installation Airman 7
Mic Placement
The headset ships with the boom positioned at the top of the headband.
Rotate the entire boom overhead to wear the microphone on either the right or
left side of the head.
CAUTION: There are two(2) stops below the boom housing. Rotating the
boom past these stops will cause damage to the unit. The boom
microphone is rotated upward to move to the other side of the
headset.
***Do not rotate past the built-in stops. Doing so will damage
the microphone.***
FIGURE 6. Boom Mic Rotation
Page 19
Bosch Security Systems, Inc.
Operating Instructions
F.01U.307.689
Rev. 02
Airman 7 Installation 19
To properly place the mic, do the following:
1. Rotate the boom to the side you want to use (left or right).
2. Bend the boom to position the mic in front of the mouth.
NOTE: For best noise-cancelling quality, place the boom mic as
close to the mouth as possible and speak into the mic.
Microphone Gain Adjustment
The Microphone Gain has been factory-adjusted to the nominal level
required for normal radio operation.
IMPORTANT: Under normal circumstances microphone gain does not
require adjustment. If needed, adjustment by an
authorized aviation technician is recommended. For
instructions on how to adjust the Microphone Gain, see
the Customer Maintenance Manual, located on
www.telex.com.
FIGURE 7. Mic Placement
Page 20
Bosch Security Systems, Inc.
Operating Instructions
F.01U.307.689
Rev. 02
20 Installation Airman 7
Clothing Clip Assembly and Attachment
Using the clothing clip reduces the cord weight from the headset. The clothing
clip comes attached to the cord and only needs to be adjusted up or down for
best use.
FIGURE 8. Clothing Clip Assembly and Attachment
Page 21
Bosch Security Systems, Inc.
Operating Instructions
F.01U.307.689
Rev. 02
CHAPTER 3
Care & Maintenance
Recommended Maintenance Schedule
NOTE: Ear cushions, headband pads, and microphone wind screens are
considered wear items. For proper headset performance these
items need to be inspected and replaced at regular intervals. See
maintenance schedule (below) for more information. Headset
performance diminishes if not replaced when deterioration or
damage is apparent.
Task
Per Use Monthly 6
Months
Check Boom Mic Placement X
Check Ear Cup Placement X
Check Headband Fit X
Inspect And Clean Connectors X
Clean Windscreen X
Clean Ear Cushions X
Clean Headband Pad X
Check Connection Cable X
Inspect & Replace Windscreen X
Inspect & Replace Ear Cushions X
Inspect & Replace Headband Pad X
Page 22
Bosch Security Systems, Inc.
Operating Instructions
F.01U.307.689
Rev. 02
22 Care & Maintenance Airman 7
Cleaning the Headset and Connectors
IMPORTANT: Do not allow any liquid to puddle on the unit or touch the
speaker or microphone element directly.
To clean the headset, do the following:
> Using a mild detergent with water and a soft towel, or isopropyl
alcohol wipes, clean the plastic and metal headset parts.
IMPORTANT: Do not soak or allow liquid to puddle on the unit.
Cleaning the Ear Cushions and Headband
Pads
IMPORTANT: Do not soak cushions or pads.
To clean the ear cushions and headband pad, do the following:
> Using a damp (not wet) soft towel or isopropyl alcohol wipes, gently
wipe the ear cushions and headband pad thoroughly.
Replacing Ear Cushions and Headband Pads
To ensure optimal product performance, it is recommended you replace ear
cushions and headband pads periodically (every six (6) months or sooner, if
needed).
To remove the ear cushions, do the following:
1. Grasp the edge of the ear cushion where it folds into the slot on the
ear cup.
2. Gently pull the ear cushion up and away from the ear cup.
3. Starting at the top of the ear cup (1), carefully work the cushion
around the cup (2) until it is in place (3).
Page 23
Bosch Security Systems, Inc.
Operating Instructions
F.01U.307.689
Rev. 02
Airman 7 Care & Maintenance 23
4. Verify the cushion is seated properly before use.
To remove the headband pads, do the following:
1. Grasp the edge of the headband pad.
2. Gently pull the headband pad away from the headband.
To replace the headband pad, do the following:
1. Remove the paper from the sticky side of the headband cushion.
2. Align the headband pad with the recessed area on the headband.
3. Firmly press the headband pad into place.
Page 24
Bosch Security Systems, Inc.
Operating Instructions
F.01U.307.689
Rev. 02
24 Care & Maintenance Airman 7
Installing or Replacing the Hygienic Covers
NOTE: Two hygienic covers are included with the headset. However,
extra hygienic covers can be purchased separately.
To replace the hygienic covers, do the following:
1. Grasp the edge of the hygienic cover where it folds into the slot on
the ear cup.
2. Gently pull the hygienic cover up and away from the ear cup.
3. Starting at the top of the ear cup, carefully work the cover around the
ear cup until it’s in place.
Cleaning or Replacing the Windscreen
The foam windscreen can be cleaned using low pressure air to blow
contaminates off from the exterior, If low pressure air does not provide
effective results the windscreen should be replaced.
IMPORTANT: Do not clean the windscreen while installed on the
microphone. Do not use any liquid on the foam
windscreen.
To remove the windscreen, do the following:
> Grasp the microphone windscreen and gently pull away from
microphone.
To replace the windscreen, do the following:
> Slide new windscreen over microphone.
Page 25
Bosch Security Systems, Inc.
Operating Instructions
F.01U.307.689
Rev. 02
Airman 7 Care & Maintenance 25
Headset Storage
To store the headset, do the following:
1. Move the boom mic above the headband.
2. Fold the ear cups flat.
Page 26
Bosch Security Systems, Inc.
Operating Instructions
F.01U.307.689
Rev. 02
26 Care & Maintenance Airman 7
3. Coil the cord into a loop.
4. Place the coiled cord and headset in a box or protective case.
OR
Place the coiled cord and headset in the optional carrying case
(see “Part Number Information” on page 35).
Page 27
Bosch Security Systems, Inc.
Operating Instructions
F.01U.307.689
Rev. 02
CHAPTER 4
Troubleshooting
Troubleshooting
• “No one can hear me when I talk” on page 28.
• “Others only hear me sporadically or my voice is distorted and
unintelligible” on page 29.
• “I cannot hear anyone who is trying to speak to me” on page 30.
• “I hear others only sporadically or what I hear is distorted and
unintelligible” on page 31.
Page 28
Bosch Security Systems, Inc.
Operating Instructions
F.01U.307.689
Rev. 02
28 Troubleshooting Airman 7
Issue Possible Cause Solution
No one can hear me
when I talk
• Microphone not
connected
correctly.
• Verify microphone
is plugged in
correctly.
• Verify no breaks
or damage to cord
(If damaged,
headset needs to
be serviced).
• Microphone is not
placed correctly.
• Reposition
microphone to
correct location
closely to front of
mouth. For more
information, see
“Mic Placement”
on page 18.
• Intercom system
is not adjusted
properly, not
functioning, or
compatible with
microphone.
• Authorized
avionics
technician or
repair facility
needs to readjust
and re-test
microphone
amplifier.
• Microphone gain
is not adjusted
properly.
• Authorized
avionics
technician or
repair facility
needs to readjust
and re-test
microphone
amplifier.
• Microphone is not
functioning.
• Return headset to
authorized repair
center for
maintenance.
Page 29
Bosch Security Systems, Inc.
Operating Instructions
F.01U.307.689
Rev. 02
Airman 7 Troubleshooting 29
Others only hear me
sporadically or my
voice is distorted and
unintelligible
• Microphone is not
located correctly.
• Reposition
microphone to
correct location
closely to front of
month. For more
information, see
“Mic Placement”
on page 18.
• Microphone
windscreen is
missing or needs
to be replaced.
• Replace
Windscreen
For more
information, see
“Cleaning or
Replacing the
Windscreen” on
page 24.
• Pilot is speaking
to loudly or to
quietly into the
microphone.
• Alter speaking
level.
• Intercom system
is not adjusted
properly, not
functioning, or not
compatibly with
microphone.
• Authorized
avionics
technician needs
to verify
compatibility and
proper of function
of the intercom.
• Microphone gain
is not adjusted
properly.
• Authorize avionics
technician or
repair facility
needs to re-adjust
and re-test
microphone
amplifier.
• Microphone is not
functioning.
• Return headset to
authorized repair
center for
maintenance.
Issue Possible Cause Solution
Page 30
Bosch Security Systems, Inc.
Operating Instructions
F.01U.307.689
Rev. 02
30 Troubleshooting Airman 7
I cannot hear anyone
who is trying to speak
to me
• Headphones not
connected
correctly.
• Verify headphone
is plugged in
correctly.
• Verify no breaks
or damage to
cord.
• Headphones are
not worn properly.
• Reposition
headphones to
ensure properly
covering the ear.
For more
information, see
“Headset
Adjustment” on
page 16.
• Intercom System
is not adjusted
properly, not
functioning, or not
compatible with
headphones.
• Authorized
avionics
technician needs
to verify
compatibility and
proper function of
the intercom.
• Headphone
volume setting is
not adjusted
properly.
• Adjust volumes,
as required (if
equipped).
• Headphones are
not functioning.
• Return headset to
authorized repair
center for
maintenance.
• Sidetone volume
levels are not
correct (only
applies to not
being able to hear
yourself over
sidetone.
• Adjust the
sidetone level on
the intercom or
radio system, if
applicable.
Issue Possible Cause Solution
Page 31
Bosch Security Systems, Inc.
Operating Instructions
F.01U.307.689
Rev. 02
Airman 7 Troubleshooting 31
I hear others only
sporadically or what I
hear is distorted and
unintelligible
• Headphones have
poor connection
to the aircraft.
• Check and clean
connectors and
re-connect to
aircraft.
• Headphones are
not properly
positioned.
• Reposition
headphones to
ensure properly
covering of the
ear. For more
information, see
“Headset
Adjustment” on
page 16.
• Headphone ear
cushions are
missing or need to
be replaced.
• Replace ear
cushions
For more
information, see
“Replacing Ear
Cushions and
Headband Pads”
on page 22.
• Intercom system
is not adjusted
properly, not
functioning, or not
compatible with
headphones.
• Authorized
avionics
technician needs
to verify
compatibility and
proper function of
the intercom.
• Headphone
volume setting is
not adjusted
properly.
• Adjust volumes,
as required (if
equipped).
• Headphone are
not functioning.
• Return headset to
authorized repair
center for
maintenance.
Issue Possible Cause Solution
Page 32
Bosch Security Systems, Inc.
Operating Instructions
F.01U.307.689
Rev. 02
32 Troubleshooting Airman 7
Label Information
The Datamatrix ECC200 holds the following information:
• CTN Number
• Serial Number
• SAP Part Number
• Datamatrix ECC200
FIGURE 1. Box Label Information
FIGURE 2. Example Headband
Page 33
Bosch Security Systems, Inc.
Operating Instructions
F.01U.307.689
Rev. 02
CHAPTER 5
Specifications
Specifications
Receiver
Type Dynamic
Impedance AIRMAN7-0220, AIRMAN7-0211
600 +/-20% @ 1 kHz
AIRMAN7-0110
300 +/-20% @ 1 kHz
AIRMAN7-0210, AIRMAN7-0000
150 +/-20% @ 1 kHz
Frequency Response
(Per RTCA DO-214a)
< 10dB max. to min. over the range of 350 to
3500Hz
Sensitivity
(Per RTCA DO-214a)
For models AIRMAN 7-0220, AIRMAN 7-0211
92 dB +/- 5 dBSPL
For model AIRMAN 7-0110
95 dB +/- 5 dBSPL
For models AIRMAN 7-0210, AIRMAN 7-0000
98 dB +/- 5 dBSPL
Page 34
Bosch Security Systems, Inc.
Operating Instructions
F.01U.307.689
Rev. 02
34 Specifications Airman 7
Microphone and Amplifier
(not applicable for Airman7.000 listen-only)
Element Type Noise-canceling amplified electret
Frequency Response
(Per RTCA DO-214a)
Sensitivity
(Per RTCA DO-214a)
-28dB +/- 2 dB re 1V/Pa @ 1kHz, 12V
Operating Voltage
(Per RTCA DO-214a)
8-28 VDC (470 Ohm TSO load circuit)
Connector Type
For models AIRMAN 7-0210, AIRMAN 7-0211, AIRMAN 7-0110
Microphone
PJ-068 (equivalent)
Headphones
PJ-055 (equivalent)
For models AIRMAN 7-0220
Microphone and Headphones
5-pin Male XLR
For model AIRMAN 7-0000
Headphones
PJ-055 (equivalent)
Page 35
Bosch Security Systems, Inc.
Operating Instructions
F.01U.307.689
Rev. 02
Airman 7 Specifications 35
Part Number Information
Physical
Weight headset weight
(with cord)
wearing weight
(without cord)
Airman7-0210 ~5.7 oz. (~161.6 g) ~3.3 oz. (~93.6 g)
Airman7-0220 ~5.9 oz. (~167.3 g) ~3.3 oz. (~93.6 g)
Airman7-0211 ~5.7 oz. (~161.6 g) ~3.3 oz. (~93.6 g)
Airman7-0110 ~4.9 oz. (~138.9 g) ~2.5 oz. (~70.9 g)
Airman7-0000 ~3.7 oz. (~104.9 g) ~2.8 oz. (~81 g)
Cord Length
6 ft. +/-4 in. (1.8 m +/- 10.0 cm)
Color Black and stainless steel
CTN Description
AIRMAN7-0210 Double Side Headset, 2PJ, 150 Ohm
AIRMAN7-0220 Double Side Headset, XLR5, 600 Ohm
AIRMAN7-0211 Double Side Headset, 2PJ, 600 Ohm
AIRMAN7-0110 Single Side Headset, 2PJ, 300 Ohm
AIRMAN7-0000 Double Side Headphone, PJ, 150 Ohm
AIRMAN8-0900 Windscreen for Airman 7 or 8, 2 pcs
AIRMAN7-0901 Foam Cushion for Airman 7 or 8, 2 pcs
AIRMAN7-0902 Supple Cushion for Airman 7 or 8, 2 pcs
AIRMAN7-0904 Clothing Clip for Airman 7 or 8
AIRMAN7-0905 Carrying Case for Airman 7 or 8
AIRMAN7-0906 Headband Pad for Airman 7 or 8
AIRMAN7-0907 Hygiene Cover for Airman 7, 10 pcs
Page 36
Bosch Security Systems, Inc.
12000 Portland Avenue South
Burnsville, MN 55337 U.S.A.
www.boschcommunications.com
Loading...