Teletronics TT5800 Users Manual

TT5800 Quick User Guide

802.11a 310mW

Package Contains

1. TT5800 802.11a PCBA (1)

2. IEEE 802.11a miniPCI radio card (1)

3. Power over Ethernet Injector (1)

4. 48VDC Power Adapter (1)

5. Ethernet Cable (2)

6. Waterproof RJ-45 Connector (1)

7. Mounting Hardware (1)

8. 23dBi Subscriber antenna,

9. 20cm RF cable (cable loss: 8dB)

10. User Manual

Quick Installation

Always double check for any missing parts from the kit you received before deployment.

Next step is to set up the computer Ethernet interface for configuring the TT5800. Since the default IP Address of the
unit is on the 192.168.10.x IP range in both Client Bridge and AP mode you’ll need to set the computer Ethernet
interface within the same IP range, such as 192.168.10.66.

Hardware Installation

Follow the procedure below to install your TT5800 device:

1. Select a suitable place on the network to install the TT5800. For best wireless reception and performance the
external antenna should be positioned within Line of Sight from the AP with proper alignment.

2. Connect the TT5800 to the ODU side of the PoE Injector via a straight Ethernet cable (Cat-5), then connect the
NET side of the PoE Injector to either a computer or an Ethernet Switch.

Note: The TT5800 now fully supports the MDI/MDI-X standard and no longer require the use of cross over cable to
connect directly with a computer.

3. Connect the 48VDC power adapter to the power jack on the PoE injector to power on the TT5800.

Check the LEDs on the TT5800 to confirm if the status is okay. At this point the PWR and LAN LEDs should be on
green. The WLAN light should light up once the unit is associated wirelessly with another wireless device. However
at this point the unit is still in factory default setting so do not the alarmed that the WLAN light doesn’t light up.

Web Control Interface

Default IP Address in Client Bridge Mode: 192.168.10.241

Default IP Address in Access Point Mode:

192.168.10.240

Default Login / Password: Nothing needs to be typed in for login and password authentication.

For detailed instructions on how to configure the TT-5800, please refer to
www.teletronics.com/Support.html

TT5800 is current designed to be configured only for the point-to-point operation mode, one access point
(AP)and one access client (AC) are needed.
Use in the following applications:

 Financial banks and brokerage houses sensitive data transmission
 Government agencies data connection among buildings
 Central office to branch office(s) connection
 Remote wireless monitoring
 TT5800 has one antenna port, one data/power port and one console port. The antenna port is N-Type

female connector used to connect to the RF cable then to the flat panel antenna. The data/power port is
used to link to the cable from the power injector. When the TT5800 and the network/power injector are
connected together, The TT5800 is turned on and initialized if the network/power injector in the indoor
is also installed successfully.

Warranty Policy

Limited Warranty

All Teletronics’ products warranted to the original purchaser to be free from defects in materials and workmanship
under normal installation, use, and service for a period of one (1) year from the date of purchase.

Under this warranty, Teletronics International, Inc. shall repair or replace (at its option), during the warranty period,
any part that proves to be defective in material of workmanship under normal installation, use and service, provided
the product is returned to Teletronics International, Inc., or to one of its distributors with transportation charges
prepaid. Returned products must include a copy of the purchase receipt. In the absence of a purchase receipt, the
warranty period shall be one (1) year from the date of manufacture.

This warranty shall be voided if the product is damaged as a result of defacement, misuse, abuse, neglect, accident,
destruction or alteration of the serial number, improper electrical voltages or currents, repair, alteration or
maintenance by any person or party other than a Teletronics International, Inc. employee or authorized service
facility, or any use in violation of instructions furnished by Teletronics International, Inc.

This warranty is also rendered invalid if this product is removed from the country in which it was purchased, if it is
used in a country in which it is not registered for use, or if it is used in a country for which it was not designed. Due
to variations in communications laws, this product may be illegal for use in some countries. Teletronics International,
Inc. assumes no responsibility for damages or penalties incurred resulting from the use of this product in a manner
or location other than that for which it is intended.

IN NO EVENT SHALL TELETRONICS INTERNATIONAL, INC. BE LIABLE FOR ANY SPECIAL, INCIDENTAL OR
CONSEQUENTIAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESSED OR IMPLIED,
WHATSOEVER.

Some states do not allow the exclusion or limitation of special, incidental or consequential damages, so the above
exclusion or limitation may not apply to you.

This warranty gives you specific legal rights, and you may also have other rights that vary from state to state.