Teletronics FXS1 User Manual

Warranty Policy

Limited Warranty

2 Choke Cherry Road, Rockville, MD 20850 Tel: [phone] Fax: [phone]

All Teletronics’ products warranted to the original purchaser to be free from defects in materials and
workmanship under normal installation, use, and service for a period of one (1) year from the date of
purchase. Under this warranty, Teletronics International, Inc. shall repair or replace (at its option), during the
warranty period, any part that proves to be defective in material of workmanship under normal installation,
use and service, provided the product is returned to Teletronics International, Inc., or to one of its distributors
with transportation charges prepaid. Returned products must include a copy of the purchase receipt. In the
absence of a purchase receipt, the warranty period shall be one (1) year from the date of manufacture.

This warranty shall be voided if the product is damaged as a result of defacement, misuse, abuse, neglect,
accident, destruction or alteration of the serial number, improper electrical voltages or currents, repair,
alteration or maintenance by any person or party other than a Teletronics International, Inc. employee or
authorized service facility, or any use in violation of instructions furnished by Teletronics International, Inc.

This warranty is also rendered invalid if this product is removed from the country in which it was purchased,
if it is used in a country in which it is not registered for use, or if it is used in a country for which it was not
designed. Due to variations in communications laws, this product may be illegal for use in some countries.
Teletronics International, Inc. assumes no responsibility for damages or penalties incurred resulting from the
use of this product in a manner or location other than that for which it is intended.

IN NO EVENT SHALL TELETRONICS INTERNATIONAL, INC. BE LIABLE FOR ANY SPECIAL, INCIDENTAL OR
CONSEQUENTIAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESSED OR IMPLIED,
WHATSOEVER.

Some states do not allow the exclusion or limitation of special, incidental or consequential damages, so
the above exclusion or limitation may not apply to you. This warranty gives you specific legal rights, and
you may also have other rights that vary from state to state.

All Rights Reserved. Copyright 2006 Teletronics International, Inc.

RMA Policy

Product Return Policy

It is important to us that all Teletronics’ products are bought with full confidence. If you are not 100%
satisfied with any product purchased from Teletronics you may receive a prompt replacement or refund,
subject to the terms and conditions outlined below.

IMPORTANT: Before returning any item for credit or under warranty repair, you must obtain a Return
Merchandise Authorization (RMA) number by filling out the RMA form. Products will not be accepted
without an RMA number. All products being shipped to Teletronics for repair/refund/exchange must be
freight prepaid (customer pays for shipping). For all under warranty repair/replacement, Teletronics
standard warranty applies.

30-Day full refund or credit policy:
I. Product was purchased from Teletronics no more than 30 day prior to the return request.
II. All shipping charges associated with returned items are non-refundable.
III. Products are returned in their original condition along with any associated packaging, accessories,
mounting hardware and manuals. Any discrepancy could result in a delay or partial forfeiture of your credit.

Unfortunately Teletronics cannot issue credits for:
I. Products not purchased from Teletronics directly. If you purchased from a reseller or distributor
you must contact them directly for return instructions.
II. Damaged items as a result of misuse, neglect, or improper environmental conditions.
III. Products purchased direct from Teletronics more than 30 days prior to a product return request.

To return any product under 1 year warranty for repair/replacement, follow the RMA procedure.

Quick Product Guide

Technical Specs

Easy access to IP from phone set or PBX
Cost Saving - Telephone call from VPN

Features

Protocol
Supported

Supplementary
Service

FAX Support

Codec
Supported

Voice Quality

QoS
Caller ID
Tone

ADSL Env.
Firewall Env.
Security
Config. & Man.
Upgrade

Power
Operation Temp.
Humidity
Console Interface

or public Internet

Follows the existing telephone call dial plan
Easy interface to ADSL/Cable Modem or

Leased line equipment

ITU-T H.323 v2/v3/v4 compliance
SIP RFC3261

H.450 (Call Hold, Call Transfer, Call Forward)

Automatic FAX detection
Group 3 Fax relay at 2.4 - 14.4 kbps
Support T.38 protocol

G.711A/u-law, G.723.1, G.729, G.729A,
G.729B, G.729AB

VAD (Voice Activity Detection)
CNG (Comfort Noise Generation)
G.165/G.168 compliant echo cancellation
Programmable Dynamic Jitter Buffer
Bad Frame Interpolation
Provide both in-band and out of band DTMF
generation detection
Gain/Attenuation Settings
Provide progress tone: Dial Tone, Busy Tone,
2nd Dial Tone, Call-Holding Tone and
Ring-Back Tone

TOS
Generation (FSK/DTMF)
DTMF/CPT (Call Progress Tone)
Generation Detection
PPPoE
Behind NAT Router or IP sharing device
Support H.235 security function
Console port, TELNET and Web Browser
Firmware upgrade through network by
TFTP/FTP

Input AC 100V ~ 240V Output DC12V

41 ~ 104°F (5 ~ 40°C)

10% to 90% (Non-condensing)

One DB-9 RS-232 COM port

VoIP FXS1 Adapter

Item# 21-106

Network
Interface

FXS
Interface

Dimensions

Weight

Four 10/100Base-T
Ethernet RJ-45 ports
(WAN/LAN)

(1) One RJ-11 Telephone
port (FXS)
Programmable AC
impedance,
Feeding voltage,
Ring Voltage, Ring
Cadence, Loop current
and call progress tone
ON-Hook Voltage: 48Vdc
Ring Voltage: 50 V RMS
Loop Current:
Constant 23mA

4" x 4" x 1.4"

1.5 lbs (0.68kg)

Package List

1. EZLoop® VoIP FXS1 Unit

2. AC Adapter

3. Ethernet Cable

4. Quick Product Guide

Sample Application Diagram Initial Set-Up Guide (Cont.)

5. Optional Set-up:

Connect the FXS1 #1 port to your Router instead of DSL or Cable modem.
Teletronics recommend places the FXS1 in front of Router to maximize the
voice quality.

FXS1

6. Configuring from Web Browser:

FXS1 WAN: default to DHCP Client

DSL/CABLE MODEM

FXS1 LAN IP: 10.1.1.3

Web IP Address: http://10.1.1.3
User ID: root
Password: (No Password/Leave it blank)

INTERNET

LAPTOP/NOTEBOOK

ANALOG
PHONE

Initial Set-Up Guide

1. Using the Ethernet

Using the Ethernet cable provided, connect the DSL or Cable modem to the #1 port
on the back of the FXS1.

2. Connect the Ethernet

Connect the Ethernet (LAN) port of your Router or your computer by using your own
Ethernet cable into the ports #2, #3, or #4.

3. Power on the FXS1

Power on the FXS1 by using the AC Adapter provided.

4. Connect your phone

Connect your phone to the Phone1 port on the back of the FXS1.

Please Note:

Please download FXS1 User Manual at www.teletronics.com/User Manuals.html

PLEASE VISIT OUR WEBSITE AT WWW.TELETRONICS.COM FOR MORE INFORMATION