Teletronics EZBridge Sample Applications User Manual
Application Note
to construct a network between
mode on basic network
If you encounter problems during the
The Access Point can swap between these two
. In this
application note, we will give two examples to show
you how to construct a network with the two modes of
the Access Point. Figure 1 is the example of
connecting two networks wirelessly. Figure 2 is the
sing the Access Point as an access
between the
mode,
.
Access Point
One or more PCs (desktop or notebook) with Ethernet
to
k
or Netscape
with
Figure 1
both of
Web
of
. Figure 4
Web management configuration
Network
. Figure 5 shows
Once you have configured all of the PCs on your network with
values, the setup and installation of connection
This guide is for you
wired and wireless network with the Access Point.
This sheet will guide you how to install Access Point
mode and Station/Bridge
step by step.
installation, please refer to your User Manual.
Introduction
modes: Access Point and Station/Bridge
application of u
point repeater.
Note: To have your Access Point switched
Access Point mode and the Station/Bridge
please refer to the AP Station Upgrade Quick Guide
Figure 1: Connect two networks wirelessly
Notebook
LAN
WA1300 Access Point
WA1300 Access Point
Figure 2: AP Repeater
Donald^^11
WA1300 Bridge/Station
WA1300 Bridge/Station
WA1300 Access Point
Application 1: Connect Two Networks Wirelessly
System Requirements
a) Two Access Point devices. One sets to
mode and the other sets to Station/Bridge mode.
b)
interface. Set its IP address, for example,
192.168.1.200 and Subnet mask to 255.255.255.0.
c) TCP/IP protocol must be installed on all PCs.
d) Network cables. Use standard 10/100BaseT networ
(UTP) cables with RJ45 connectors.
e) Microsoft Internet Explorer 5.0 or later
Navigator 4.7 or later.
Installation Instructions
a) Use straight LAN cable to connect the Access Point
one LAN, and Station/Bridge with the other.
shows the placement.
b) Connect the power adapter to the power jacks on
Access Point and Station/Bridge.
c) Open the Web browser to enter the Access Point
management page, and then set the Network Name
Access Point to, for example, wirelesslan
shows the Access Point
Mac II
PC
page.
Figure 4: Access Point Web management configuration page
d) In the Station Web management page, set the
Name of Station/Bridge to wirelesslan
the Station Web management configuration page.
Notebook
Figure 3: Installation Diagram
002
2503500500
Figure 5: Station Web management configuration page
appropriate
between two networks are complete.
mode and the other to
One PC (desktop or notebook) with Ethernet
to, for example,
to
(For setting all Access Point
10/100BaseT
with
AP1
on
to, for example,
Web management page. Figure 4
Web management configuration
to, for example,
Web management page.
management
PC
/Station.
to, for example,
Web management
Web
to, for example,
Web management
Web
PC
.
on
to, for example,,
Web management page.
Web
to, for example,
Web management page.
administration
AP1
Once you have configured all the Wireless PCs on the two
AP
Application 2: AP Repeater
System Requirements
a) Three Access Point devices. Set two of them to
Access Point
Bridge/Station mode.
b)
interface. Set its IP address
192.168.1.200 and Subnet mask
255.255.255.0.
devices)
c) TCP/IP protocol must be installed on PC.
d) Network cables. Use crossover
network (UTP) cables with RJ45 connectors.
e) Microsoft Internet Explorer 5.0 or later or
Netscape Navigator 4.7 or later.
Installation Instructions
a) Use crossover LAN cable to connect PC
one Access Point. Here we label it as
hereafter.
b) Connect the power adapter to the power jack
AP1.
c) Set the Network Name of AP1
rep on AP1
shows the AP
page.
d) Set the IP address of AP1
192.168.1.80 on AP1
Figure 6 shows the AP
administration page.
e) Use crossover LAN cable to connect
f) Connect the adapter to power jack on STA.
g) Set the Network Name of STA
h) Set the IP address of STA
(disconnect to AP1) with one Bridge
Here we label it as STA hereafter.
wirelesslan on Station
page. Figure 5 illustrates the Station
management configuration page.
192.168.1.99 in the Station
page. Figure 7 illustrates the Station
management administration page.
Figure 6: AP management administration page
002
2503500500
Figure 7: Station management administration page
i) Use crossover LAN cable to connect
(disconnect to STA) with the other Access Point
Here we label it as AP2 hereafter.
j) Connect the power adapter to the power jack
AP2.
k) Set the Network Name of AP2
wirelesslan on AP2
Figure 4 shows the Access Point
management configuration page.
l) Set the IP address of AP2
192.168.1.90 on AP2
Figure 6 shows the AP management
page.
m) Use crossover LAN cable to connect
(disconnect to AP2) with STA.
networks with appropriate value of Network name, the
Repeater setup and installation are complete.
2503501400
Loading...