Teletronics EZBridge AP User Manual

Quick Installation

between

wired and wireless network. You will learn how to

on your network step by step.

If you have any problems during the installation,

access

The access point is compliant with the IEEE

Small as the sparrow

are damaged or missing,

One or more PCs (desktop or notebook) with

Network cables. Use standard 10/100BaseT

Microsoft Internet Explorer 5.0 or later or

Access Point

onnect the power adapter to the power jack on the

on when the

Power on one of the PCs and login if you are asked to.

on the

Control

This guide is for you to make a connection
install the Access Point
please refer to your User Manual.

Introduction

Congratulations on the purchase of your new

point.

802.11b (DSSS) specifications.
is, it possesses all its internal organs.

Package Contents

The following items should be included:

a) One Access Point Unit (the device).
b) One Power Adapter.
c) One User’s Manual.
d) One Quick Installation Guide.

If any items listed above
please contact your dealer immediately.

System Requirements

a)

Ethernet interface.

b) TCP/IP protocol must be installed on all PCs.
c)

network (UTP) cables with RJ45 connectors.

d) All wireless devices must be compliant with the

IEEE 802.11b specifications.

e)

Netscape Navigator 4.7 or later.

WA1300 Access Point

Notebook

Donald^^11

Notebook

PC

Figure 1: Network Connection

002
2503500500

Notebook

Mac II

Installing Your Access Point

Take Windows 98 platform for example

Figure 2: Installation Diagram

Installation Instructions

a) Use straight LAN cable to connect the

with a hub of the wired network.

b) C

Access Point.

The Power LED (the right one) should be

power adapter is connected.

c) Use straight LAN cable to connect the PC with the

wired network.

d)

When you reach the desktop, click Start
taskbar, select Settings , and then select
Panel.

e) Double-click the Network icon to open the Network

dialog box as below.

Figure 3: Network Configuration

f) Select the TCP/IP protocol for your network card.

as

an IP

should be ranged from 1 to 254 and is never used

again. Windows may copy files to your

you will be asked to restart

your computer and

t asked,

manually restart the computer to ensure the

you just

type

field.

User

User

shown

g) Click the Configuration tab and type texts in the

, for example.

,

following

function. Follow the steps below (take 64 bit encryption

select the

WEP key

10 hex digits into the key box

WEP key

the

Once you have configured all of the PCs on your

values of Network name and

WEP key, the access point setup and installation are

For instructions on MAC address filtering or other

o) Click Properties. You will then see a dialog box

shown below.

Figure 4: IP Address

p) Ensure your TCP/IP settings are correct

follows.
To use static IP address, select Specify
address. Type 192.168.1.200 in the IP address
field and 255.255.255.0 in the Subnet Mask field.

The IP address must be 192.168.1.x. The value of x

by other PCs.

q) Click OK

computer, and then

your PC. Click Yes to restart

initiate the new settings. If you aren’

system has used the IP address

specified.

r) Open your Web browser and

“HTTP://192.168.1.90” in the Address

Then press Enter.

Figure 5: Enter Web Address

s) A logon dialog box will appear. The default

Name is root and Password is root. Put

Name and Password and Click OK.

Figure 6: User name/Password Dialog Box

t) After you click OK, the Setup screen is

like the following figure.

002
2503500500

Figure 7: Setup Screen

Network name field, wirelesslan
After setting the Network name, click Save

Reboot, and then OK.
The Configuration screen is shown as the
figure.

For the purpose of security, you can enable the WEP
for example):
h) Click the Encryption tab, and then

WEP enabled function.

i) Choose 64 bit on the right side of the

lengths field. Type

at the right of the WEP key 1 field.

j) Choose Key 1 on the right side of the

to use field.

k) Select the Deny unencrypted data option.
l) Choose Shared Key in the Authentication field.
m) Click Save, Reboot, and then OK in sequence.
n) The Configuration screen is shown as

following figure.

network with appropriate
complete.

advanced configurations, refer to your User Manual.

2503501200