Teletronics EZ Bridge 802.11B User Manual
EZ Bridge 802.11B 100mW Product Guide
Section - Product Information
I. Introduction
Product Name: EZ Bridge
Model: 802.11B 100mW
Item Number: 11-207 (PCB Kit) and 11-208 (NEMA4 Box)
II. Technical Specs
Protocol: IEEE 802.11b
Spreading: Direct Sequence Spread Spectrum (DSSS)
Modulation: DBPSK @ 1Mbps; DQPSK @ 2Mbps; CCK @ 5.5 and 11Mbps
Frequency Band: 2.4 GHz (ISM band)
Data Rate Supported: 1, 2, 5.5, and 11 Mbps
RF Configuration Modes: Station Bridge, Ad-Hoc and AP modes supported
Operating Channels: 11 channels (US, Canada
Transmit Gain: 20±1dBm (~100 mW) Typical; 27 dBm (500mW) with optional amplifier
Receive Sensitivity: 1 Mbps: -93 dBm, 2 Mbps: -90 dBm, 5.5 Mbps: -85 dBm, 11 Mbps: -82 dBm
TX/RX Range: (In free space)
Indoor: 11, 5.5 Mpbs = 164 Ft. (50 m); 2, 1 Mbps = 360 Ft. (110 m)
Outdoor: 11, 5.5 Mbps = 787 Ft. (240 m); 2, 1 Mpbs = 1968 Ft. (600 m)
Antenna Connector: MMCX Connector (Use connector nearby the LED for Outdoor Installations.)
Uplink: 10 base T Ethernet
Network Architecture Types: Infrastructure
Security Filter: MAC Address Filtering
Regulatory Approval: FCC Part 15, Sec. 15.247, Sec. 15.107 and Class B
Weight PCB: 195g (6.87 oz)
Dimensions PCB: 5.75" L x 3.38" W x 1.25" H (15cm L x 8.5cm W x 3cm H)
Weight w/ NEMA4 Box: 1.13 Kg (2.5 lb)
Dimensions w/ NEMA4 Box: 7" L x 5.4" W x 2.8" H (18cm L x 13.8cm W x 7.3cm H)
Environmental:
Operating Temperature: -20°C to 70°C (-4°F to 158°F)
Humidity: 10 to 90% (non-condensing)
AC Adapter:
Input 120 VAC -- 60 Hz -- 10 W
Output 7.5 VDC -- 1.5 A
III. Package List
1. EZBridge
2. Power over Ethernet Injector
3. AC/DC Power Adapter
4. Ethernet Cable
5. Ethernet Crossover Cable
6. Waterproof RJ-45 Connector
7. Mounting Hardware
8. User Manual
Section - B Quick Setup Guide
I. Initial Setup
Requirements
¸ One or more PCs (desktop or notebook) with Ethernet interface.
¸ TCP/IP protocol must be installed on all PCs. (Refer to User Manual for additional information)
¸ Network cables. Use standard 10/100BaseT network (UTP) cables with RJ45 connectors.
¸ All wireless devices must be compliant with the IEEE 802.11B specifications.
¸ Microsoft Internet Explorer 5.0 or later or Netscape Navigator 4.7 or later.
* To avoid damage to the EZ Bridge, do not connect the power adapter to a power source until all other
connections has been established.
II. Unit login info
After all initial setup requirements are checked type the following IP under the address bar of a web browser to
login.
EZ Bridge Default IPs
In AP Mode: 192.168.1.99
In Client Mode: 192.168.1.99*
Authentication: Nothing needs to be typed for login and password.*
* The default factory setting for EZ Bridge 802.11B.