Telematrix 3300IP User Manual

3300IP VOIP Phone
User Manual
TeleMatrix, Inc
1
1.1 Overview of Hardware…………………………………………………………..5
1.2 Overview of Software……………………………………………………………5
2 Keypad of 3300IP…………………………………………………….……………...6
2.1 Function Table of Keyboard
………………………………………………….....6
2.2 Keyboard function and LCD Menu catalog……………………………………..7 3 Program the Phone via a WebBrowser…….……………………………………...10
3.1 Login..
…………………………………………………………………………..10
3.2 Current state…………………………………………………………………….10
3.3 Networ k………………………………………………………………………….11
3.3.1 WAN Config...................................................................................................11
3.3.2 LAN Config………………………………………………………………...13
3.4 VoIP
……………………………………………………………………………..13
3.4.1 SIP Config…………………………………………………………………...13
3.4.2 Iax2 Config………………………………………………………………….15
3.5 Advance…………………………………………………………………………16
3.5.1 DHCP Server……………………………………………………………..….16
3.5.2 NAT
………………………………………………………………………….17
3.5.3 STUN ………………………………………………………………………..18
3.5.4 Net Service…………………………………………………………………..19
3.5.5 Firewall settings
……...………………………………………………………20
3.5.6 QoS settings...………………………………………………………………..21
3.5.7 Digital Map…………………………………………………………………..21
3.5.8 Call Service Settings………….……………………………………………...23
3.5.9 Memory Key ………………………………………………………………...24
3.5.10 MMI Filter
………………………………………………………………….24
3.5.11 Audio Settings……………………….……………………………………..25
3.5.12 VPN………………………………………………………………………...25
3.6 Dial-Peer dial rule setting……………………………………………………….26
3.7 Config Manage………………………………………………………………….27
3.8 Update
…………………………………………………………………………...28
3.8.1 Update……………………………………………………………………….28
3.8.2 Auto Update…………………………………………………………………29
3.9 System Manage
…………………………………………………………………30
3.9.1 Account Manage…………………………………………………………….30
3.9.2 Syslog Config………………………………………………………………..30
3.9.3 Phone Book………………………………………………………………….31
3.9.4 Time Set…………………….……………………………………………….31
3.9.5 MMI SET
…………………………………………………………………….32
3.9.6 Logout & Reboot…………………………………………………………….32
4 Operating Method for Dialing…………………………………………………….33
4.1 How to dial IP Phone
…………………………………………………………...33
4.2 Set the Phone to Server…………………………………………………….....,33
2
4.2.1 Set WAN Interface
p
N
…………………………………………………………33
4.2.2 SIP Setting………………………………………………………………….35
4.2.3 IAX Setting………………………………………………………………...36
4.3How to Use Dialing Rules……………………………………………………….36
4.4 Voice mail……………………………………………………………………….38
Reset to Factory Default:
To reset the phone to the factory default settings, press “#” during the startup procedure ( At
ower up you can see a black progress bar). The phone will enter into “post” mode, then input
* # 1 6 8 ”. Then you will see “clearing conf” on the screen, next you see “conf reset”. Now you have reset to the default settings.
Default IP Address = 192.168.10.1
Login = admin
Password = admin
If phone’s default IP address has changed from 192.168.10.1, the current IP address can be displayed by using the submerged keys below the faceplate. To Enter the Menu, hold the Left/Store key for 3 seconds and enter default password of 123.
"STORE" key is "MENU"
"FLASH" key is "ENTER"
Scroll using Vol "+" or "-" key.
Check the IP address via the menu of:
ETWORK>WAN >Status
3
Functions
1.
Support two SIP servers working at the same time
2.
Provide a Backup SIP Server
3.
Support NAT (Network Address Translation), Firewall
4. Support DHCP assignment IP addresses, etc automatically
5. Support PPPoEused while connecting ADSLcable modem
6.
Supports program updates through HTTP ,FTP and TFTP
7. Check the dynamic voice; Soften the noise; Buffer technique of voice
8.
Hold Function
9.
Hotline Function (Phone goes off-hook, specified number is dialed)
10.
Speed-dial
11.
Call-forward, Three-way conference call
12. Caller ID display
13.
DND (Do Not Disturb), Black List, Limit List
14.
Auto-answer.
15. Set through standard Web Browser
16.
Remote Management Function
17. Classification management for common user’s password and superuser’s
password.
Standards and Protocols
IEEE 802.3 /802.3 u 10 Base T / 100Base TX
PPPoE DHCP Client and Server Support G.711a/u,G729, G723.1 5.3/6.3 audio Codec SIP RFC3261, RFC 2543 Support IAX2 TCP/IP: Internet transfer and control protocol RTP: Real-time Transport Protocol RTCP: Real-time Control Protocol VAD/CNG save bandwidth Telnet: Internet's remote login protocol DNS: Domain Name Server TFTP: Trivial File Transfer Protocol
4
1. Introduction
This is the user manual for the 3300IP VoIP Phone. Some configuration and set-up is required before using the 3300IP. This manual will illustrate how to set the phone through keyboard and web service.
1.1 Overview of Hardware
1.1.1 The two RJ-45 network interface ports support 10/100M Ethernet. The default WAN interface is a DHCP Client server. User should connect the WAN interface to their Internet router ADSL or POE switch, and connect a computer to the LAN interface (default IP address is 192.168.10. 1). You can use the administrator’s user name “admin” and password“admin”to login and set program changes.
1.1.2 Only the WAN interface supports Power Over Ethernet (802.31f / POE).
1.2 Overview of Software
Network Protocol Tone
SIP v1(RFC2543)
V2(RFC3261)
IP/TCP/UDP/RTP/RTCP
IP/ICMP/ARP/RARP/SNTP
Ring Tone Ring Back Tone Dial Tone Busy Tone
TFTP Client/DHCP Client/PPPOE
Client
Telnet/HTTP Server
DNS Clients
Codec
G.711 64K bit/s(PCM)
Phone Function
Volume Adjustment Speed dial key
Phonebook G.723.1 63k/5.3k bit/s G.726: 16k/24k/32k/40k
bit/s(ADPCM)
G.729A: 8k bit/s(CS-ACELP)  G.729B: adds VAD & CNG to
IP Assignment
IP (Static IP)
DHCP
PPPoE
G.729
Voice Quality Security
VAD Voice activity detection CNG Comfortable noise
generator
LEC Line echo canceller Packet Loss Compensation Adaptive Jitter Buffer
HTTP 1.1 basic/digest
authentication for Web setup
MD5 for SIP authentication
(RFC2069/RFC2617)
QoS
QoS field
Call Function NAT Traversal
STUN Call Hold Call Waiting
Configuration
5
Call Forward Caller ID 3-way conference
Web Browser
Console/Telnet
Keypad
DTMF
DTMF RELAY DTMF RFC 2833 DTMF SIP Info
SIP Server
Support two SIP server working at
the same time
Provide a Backup SIP Server
2 3300IP phone keyboard
2.1 Keys functions Keys
Volume +
Mode
calling
mode
config
increase the volume
choose the page(page up)
mode
Volume -
calling
mode
config
reduce the volume
choose the page(page down)
mode
Enter config
confirm/enter into the next menu
mode
Menu
hold mode
calling
mode
config
enter into the speed-dial
setting menu after three seconds long pressing.
back to the last menu
mode
Redial
calling
mode
config
redial the last number and make a call
delete the existing
mode
Hold calling
call waiting
mode
CONF calling
Three way conference
mode
hold mode
M1~M10
dialing
10 speed dial numbers
mode
Voicemail
hold mode
Pick up voicemail
Firmware Upgrade
TFTP
HTTP
FTP
Function/Display
storage mode and
digits
6
1
2
3
4
5
6
7
8
9
0
*
dialing
mode
config
mode
dialing
mode
config
mode
dialing
mode
config
mode
dialing
mode
config
mode
dialing
mode
config
mode
dialing
mode
config
mode
dialing
mode
config
mode
dialing
mode
config
mode
dialing
mode
config
mode
dialing
mode
config
mode
dialing
mode
config
mode
“1”
“1”, “space”, “@”, “_”, “-”, “/”, “%”
“2”
“2”, “a”, “b”, “c”, “A”, “B”, “C”
“3”
“3”, “d”, “e”, ”f”, “D”, “E”, “F”
“4”
“4”, “g”, “h”, “I”, “G”, “H”, “I”
“5”
“5”, “j”, “k”, “l”, “J”, “K”, “L”
“6”
“6”, “m”, “n”, “o”, “M”, “N”, “O”
“7”
“7”, “p”, “q”, “r”, “s”, “P”, “Q”, “R”, ‘S”
“8”
“8”, “t”, “u”, “v”, “T”, “U”, “V”
“9”
“9”, “w”, “x”, “y”, “z”, “W”, “X”, “Y”, “Z”
“0”
“0”, “*”, “#”, “$”, “&”, “?”, “!”, “<”, “>”
“*”
“*”, “.”
7
calling
# dialing
2.1.1 Voice Control
Press “VOL+”to increase the volume and press “VOL-”to decrease.
2.1.2 Hold Function
When you are in communication on one line and also another line, you can switch between calls using the “Hold” key.
mode
mode
Realize the 3-way conference call by pressing # under the Hold mode dial as the first number or finish number sign
2.2 Functions and Settings / LCD Menu Catalog
T o determine settings as well as modify a subset of the phone’s features, you must enter the programming mode. This is done by navigating the submerged keys found underneath the 3300Ips faceplate. The left key is “Menu” and servers to back out of the menu tree. The right “Enter” key serves to select and move forward through the menu tree.
1. Press down the left submerged “Menu” key to program a speed dial button. Input the intended speed dial number. Finally, press the corresponding speed dial key to save.
2. Enter the programming mode by pressing down the left submerged “Men u” key for 3 seconds. You will be prompted to “Input Password”… the default password is 123, then you can press the right submerged “Enter” key to begin navigating the phone’s programming menus through the LCD.
3. When modifying settings, press “Redial” to enter modification status, and “0” is to make no choice, “1” is to make choice, “Enter” is to confirm the modification, “Menu” is to quit the modification. After finishing the modification setting, we will save it on “Save” menu. After rebooting all the settings will be go into effect.
4、Menu catalog:
1) Network
2) Call Feature
3) SIP
4) DSP
5) System
6) Other Setting
2.2.1 Network:
2.2.1.1 LAN
1)
Bridge Mode
2) IP
3)
Netmask
4)
DHCP Server
Switch
8
DNS Relay
5)
NAT
Switch FTPalg PPPTPalg
2.2.1.2 WAN
1)
Status
2) Static Net
IP NetMask Gateway DNS DNS2
3) PPPoE
User name Password
4) QoS
2.2.2 Call Feature
2.2.2.1 Phone-number
1)
Public SIP
2) Private SIP
2.2.2.2 Limit-List
1)
Current
2) ADD
3)
DEL
2.2.2.3 Black-List
1) Current
2)
ADD
3) DEL
2.2.2.4 FastCall
2.2.2.5 Three Talk
2.2.2.6 Call-Transfer
2.2.2.7 Call-Waiting
2.2.2.8 Call-Forward
1) Condition
2)
SIP
Transfer Num Transfer IP Port
2.2.2.9 Dial-Rule
1)
End With #
2) Fixed Length
Switch Length
9
2.2.3 SIP
2.2.3.1 Reg Status
1) Public Reg
2)
Private Reg
2.2.3.2 Reg Switch
1)
Public
2) Private
2.2.3.3 Server
1)
Public
2) Private
2.2.3.4 Domain
1)
Public
2) Private
2.2.3.5 User Agent
1) Public
2) Private
2.2.3.6 Detect-server
2.2.3.7 Dtmf-mode
2.2.3.8 Interval-time
2.2.3.9 Swap-server
2.2.3.10 RFC-version
2.2.3.11 Signal-Port
2.2.3.12 Stun
1)
Switch
2)
Addr
3) Port
4)
Expire T i me
2.2.4 DSP
2.2.4.1 Codec
2.2.4.2 Handdown-time
2.2.4.3 Dtfm-Volume
2.2.4.4 Input-Volume
2.2.4.5 Output-Volume
2.2.5 System
2.2.5.1 Save
2.2.5.2 Reboot
2.2.5.3 Set Default
2.2.6 Other Setting
2.2.6.1 Syslog
1) Switch
2) Server-IP
3)
Server-Port
10
3 Programming the phone via a web browser
Insert one end of an Ethernet cable into the network interface of your computer, then insert the other end to the LAN interface of the phone (jack furthest from the handset). The phones usually come defaulted to have an address of 192.168.10.1. They are also defaulted to parcel out an IP address to your computer so that your computer will be on the same network as the phone (such as 192.168.10.2). If this is not the case, you must manually set the IP address of your computer 192.168.10.xxx. Next open a web browser, such as Internet Explorer (IE) or Mozilla Firefox and input 192.168.10.1 on the add ress field. At this time you will enter the web-enable programming page of the IP phone.
3.1 Login
The default
user name/password
admin/admin
are
or guest/guest.
3.2 Current Status
This page layout shows the operational state of the VoIP phone. The network part shows the connection state of the WAN interface and the LAN interface as well as the network setting; the work state of Public SIP service of VoIP part, and here you can see the registration and whether registered to the server or not. The Phone Number part shows the telephone numbers in Private SIP server and Public SIP server. The Firmware version of the phone is shown at the bottom of the page.
11
3.3 Network
3.3.1 Wan Config
WAN port network setting page. Supports static IP assignment, DHCP (to dynamically obtain an IP address) and PPPoE.
Configure Static IP:
----Enable Static;
----Set 3300IP’s IP address in the IP Address;
----Set network mask in the Netmask field;
----Set router IP address in the
----DNS Domain:
----Set local DNS server in the Preferred DNS and the Alternate DNS
Configure to dynamically obtain IP
----Enable DHCP
If there is DHCP server in your local network, the IP phone will automatically obtain
an IP address and WAN port network information from your DHCP server.
Gateway
;
12
Configure PPPoE:
----Enable PPPoE
----
----Enter PPPoE username and pin in the username and password.
PPPoE server
: Enter “ANY” if none is specified from your ITSP (service provider).
The IP Phone will automatically obtain WAN port network information from your ITSP
if PPPoE setting and the setup are correct.
Notice: If user accesses the IP phone through WAN port. He/She should use the new IP address to access the IP phone when the WAN port address was changed.
13
3.3.2 LAN Config
LAN IP Netmask: DHCP Server: Enable DHCP service in LAN port; after user changes LAN IP, phone
will automatically modify DHCP Lease Table and save the configuration according to IP and netmask, DHCP server configuration will not take effect until you reboot the device.
NAT: Bridge Mode:
addresses for its LAN port in bridge mode and its LAN and WAN port will be in the same network. (This setting won’t take effect unless you save the config and reboot the device)
Enable NAT.
Set the IP and Netmask for the LAN
Enable this option to switch to bridge mode. IP phone won’t assign IP
3.4 VoIP
3.4.1 SIP Config
Setting page of public SIP server:
14
Register Server Addr:
Register address of public SIP server
Register Server Port: Register port of public SIP serverdefault port is 5060
Register Username:
Username of your SIP account (Always the same as the
phone number)
Register Password:
Password of your SIP account.
Proxy Server Addr: IP address of proxy SIP server (SIP provider always use the same IP for register server and proxy server, in this case you don’t need to configure the proxy server information.)
Proxy Server Port: Signal port of SIP proxy
Proxy Username:
Proxy Password:
proxy server username
proxy server password
Domain Realm: SIP domain, enter the sip domai n if a ny, otherwise 3300IP will use the proxy server address as sip domain.
Local SIP port: Local SIP register port, default 5060
Phone Number:
Enable Register:
Phone number of your SIP account
Enable/Disable SIP register. The IP Phone won’t send
registration information to SIP server if enable register is not selected.
Enable Message WaitingThe configuration allows/forbids Message Waiting.
Advanced SIP Setting
Register Expire Time:
will auto configure this expiration time to the server recommended setting if it is different from the SIP server.
Call Forward: Please refer to Value_add_service
No answerIf no answer, it will forward to the appointed phone.
Always:The caller always forwards to the appointed phone.
Forward Photo Number:call the forwarded phone number.
register expire time, default is 60 seconds. The IP Phone
for detail.
15
Detect Interval Time:
enable, the IP phone will periodically detect if the SIP server is available according this setting.
User Agent:
Encrypt Key: The particular service system decrypts of the key, matching with the
server Type usage, the key provide by the particular service system supplier, default is empty
Server TypeThe particular service system supplier carries out the sign and speeches to encrypt, default is common
DTMF Mode: DTMF signal sending mode: support RFC2833, DTMF_RELAY (inband audio) and SIP info
RFC Protocol Edition:
need to communicate to devices (such as CISCO5300) using the SIP 1.0. Default is RFC
3261.
Co-work with the Auto Detect Server, if Auto Detect Server is
Current 3300IP SIP version. Set to RFC 2543 if the gate
3.4.2 Iax2 Config
Setting page of public IAX server:
IAX Server Addr:
Register address of public IAX server
IAX Server Port: Account Name:
number)
Account Password: Local port: Phone Number:
Voice mail number: If the IAX support voice mail, but your username of the voice
mail is letters which you can not input with the ATA, then you u s e th e number to stand for your username
Voice mail text:
here. Echo test number: If the platform supports echo test, and the number is test form, the config the test number to replace the text format The echo test is to test the ring status of terminals and platform
Echo test text: Refresh time: Enable Register: enable or disable register Enable G.729: IAX2(Default Protocol):
choose SIP as default
IAX refresh time
Using G.729 speech coding mandatory consultations
Register port of public IAX serverdefault port is 4569 Username of your SIP account (Always the same as the phone
Password of your IAX account.
Signal port of local, default port is 4569
if IAX support voice mail, config the domain name of your mail box
echo test number in text format
Phone number of your IAX account
Set IAX 2 as the default protocol , if not the system will
16
3.5 Advance
3.5.1 DHCP Server
DHCP server manage page. User may trace and modify DHCP server information in this page.
DHCP Lease Tabledisplay the IPMAC corresponding table that the server distributed.
Lease Table Name:
Start IP:
End IP: Ending IP address of lease table. Network device connecting to the 3300IP
LAN port can dynamically obtain an IP address in the scope/range between start IP and end IP.
Lease Time:
Netmask:
Gateway: Default gateway of lease table
DNS:
DNS Relay:
User may use below setting to add a new lease table.
Starting IP address of lease table.
Netmask of lease table.
default DNS server of lease table.
enable DNS relay function.
Notice: This setting won’t take ef fect unless you save the config and reboot
Lease table name.
DHCP server lease time.
the device
17
3.5.2 NAT
Advance NAT setting. Maximum 10 items for TCP and UDP port mapping.
DHCP Lease Table
IPSec ALG:
FTP ALG:
PPTP ALG:
Transfer Type:
Enable/Disable IPSec ALG;
Enable/Disable FTP ALG;
Enable/Disable PPTP ALG;
Transfer type using port mapping.
Inside IP: LAN device IP for port mapping.
Inside Port:
Outside Port:
LAN device port for port mapping.
WAN port for port mapping.
Click Add to add new port mapping item and Delete to delete current port mapping item.
Show IP—MAC corresponding t able assi gned by D HCP ser ver.
18
DMZ Config
3.5.3 STUN
This page is used to set the private sip server, stun server, and back up sip server information.
STUN Server setting: SIP STU N is u sed to real iz e SIP penetrates through N AT , when the phone configures IP and port of STUN server (default is 3478) and select Enable SIP Stun, common SIP server can be used to realize the phone to penetrate through NAT. In this way, If you have common SIP proxy and STUN server parked public network, it is all right, but STUN only support three NAT ways: FULL CONE, restricted, port restricted;
STUN Server Addr: STUN Server Port: STUN Effect Time: stun detect NAT type circle, unit: minute.
configure stun server address;
configure stun server port default 3478
19
Local SIP Port Load Use Stun
Load the choices of SIP line.
Stun. Set the Stun that allows/forbids use user setting.
The SIP port of this phone.
3.5.4 Net Service
HTTP Port: Configure the HTTP transfer port; default is 80. User may change this
port to enhance system’s security. When this port is changed, please use http://xxx.xxx.xxx.xxx:xxxx/ to reconnect.
Telnet Port: Configure telnet transfer port, default is 23.
RTP Initial Port:
RTP Port Quantity: Maximum RTP port quantity, default is 200
RTP initial port.
Notice: Settings in this page won’t take effect unless you save and reboot
the device.
If you need to change telnet port or HTTP port, please use the port greater
than 1024, because ports under 1024 is system remain ports.
HTTP service if HTTP is set to 0.
20
3.5.5 Firewall settings
Firewall setting page. User may set up firewall to prevent unauthorized Internet users from accessing private networks connected to the Internet (input rule), or prevent unauthorized private network devices to access the internet.
Access list support two type limits: input_access limit or output_access limit. Each type support 10 items maximum.
3300IP firewall filter is base WAN port. So the source address or input destination address should be WAN port IP address.
Configuration:
In_access enable
Out_access enable enable out_access rule
Input/Output:
Deny/Permit: specify current adding rule is deny rule or permit rule.
Protocol Type:
Port Range:
port range if this rule
Src Addr: source address. Can be single IP address or network address.
Dest Addr:
destination address. Can be IP address or network address.
Src Mask: source address mask. Indicate the source is dedicate IP if set to
255.255.255.255. Otherwise is network ID
Des Mask:
Destination address mask. Indicate the source is dedicate IP if set
to 255.255.255.255. Otherwise is network ID
enable in_access rule
specify current adding rule is input rule or output rule.
protocol using in this rule: TCP/IP/ICMP/UDP.
21
3.5.6 QoS settings
The IP phones implement QoS (Quality of Service) based upon 802.1p. QoS is used to mark the network communication priority in the data link/MAC sub-layer. The IP Phone will sort/prioritize the packets using 802.1p/ QoS and send them to the destination.
VLAN Enable: If VLAN service is enabled, the second layer will realize separate voice, signal and data transmission. To realize separate voice and data transmission by dispose for IP precedence of ToS area of voice transmission. To reach upper layer switch or router have priority to transfer voice transmission. (The prerequisite is the upper layer switch or router has to identify ToS area.)
VLAN ID:
function. The realized voice packet s tra nsfer at the s ame VLAN. The prerequ isite is it must the same as VLAN of upper switch. The value range are 1~4094.
DiffServ Enable: If enable the VLAN service, it indicates use DSCP mode to realize three layers QoS. This moment, the DSCP of SIP signals which between 3300IP Phone and MGC. It will use Class Selector 5 (The value is 0xA0). And the DSCP of mediums information (In RTP packets) would be used the values of DiffServ Value field.
Dispose VLAN ID is add a Tag header after realize enable the VLAN
DiffServ Value:
0x28,0x30,0x38,0x48,0x50,0x58,0x68,0x70,0x78,0x88,0x90,0x98,0xb8.default is 0xb8 ,oxb8 stands for best fast transmission; 28-38 is guarantee for the transmission priority for the 1st rank , 48-58 is guarantee for the transmission priority for the 2nd rank, 68-78 is guarantee for the transmi ssi on pri ority f or the 3r d r ank, 88- 98 i s guar antee f or t he transmission priority for the 4th rank.
802IP Priority: The priority of 802.ip
The value range
3.5.7 Digital Map
Digit map is a set of rules to determine when the user has finished dialing.
3300IP support below digital map:
22
Digital Map is based on some rules to judg e when user e nd thei r dialin g an d se nd the number to the server. 3300IP support following digital map:
----End With “#”: Use # as the end of dialing.
----Fixed Length: When the length of the dialing match, the call will be sent.
----Timeout: Specify the timeout of the last dial digit. The call will be sent after timeout
----Prefix: User define digital map:
[ ] represents the range of digit, can be a range such as [1-4], or use comma such as [1,3,5], or use a list such as [234]
x represents any one digit between 0~9
Tn represents the last digit timeout. n represents the time from 0~9 second, it is necessary. Tn must be the last two digit in the entry. If Tn is not included in the entry, we use T0 as default, it means system will sent the number immediately if the number matches the entry.
Example:
8[2-8]xxx xx All number from 8200000 to 8899999 will be sent immediately . 955xx 5 digits numbers begin with 9 will be sent immediately. 10060 Number 10060 will be sent will be immediately 22xxxxxT1 7 digits numbers begin with 22 will be sent after one second
39[3,9]xxxx, 7 digits numbers begin with 393 or 399 will be sent
immediately.
23
3.5.8 Call Service Settings
User configure the value add service such as hotline, call forward, call transfer, call waiting, 3-way conference call, auto-answer, etc in this page
Hotline: configure hotline number. 3300IP immediately dials this number after hook-off if it is set.
Auto Answer: Enable/disable auto answer function.
No Disturb:
Ban Outgoing:
Enable Call Transfer: Please refer to Value_add_service
Enable Call Waiting:
Enable Three Way Call:
Accept Any Call: If this option is disable, 3300IP refuse the incoming call when the
called number is different from 3300IP’s phone number.
No Answer Time: no answer call forward time setting.
Black List:
Limit List:
DND, do not disturb, enable this option to refuse any calls.
Enable this to ban outgoing calls.
for detail.
Enable/disable Call Waiting
Please refer to Value_add_service
for detail.
incoming call in these pho ne numbers will be refused.
outgoing calls with these phone numbers will be refused
24
3.5.9 Memory Key
This page layout shows the number setting of Voice mail and speed-dial key.
3.5.10
When MMI filter is enable. Only IP address within the start IP and end IP can access 3300IP phone.
MMI Filter
MMI filter is used to make access limit to 3300IP phone.
25
3.5.11 Audio Settings
CODEC:
Signal Standard: Signal standard for different area.
Handdown Time:
Input Volume: Handset in volume.
Output Volume:
Handfree Volume:
G729 Payload Length: G729 payload length
VAD:
select the prefer CODEC; support ulaw, alaw, G729 and G7231 5.3/6.3
hand down detect time.
Handset out volume.
Hand free volume
Enable/disable Voice Activity Detection
3.5.12 VPN
This page is VPN setting page , the IP phone support the VPN with UDP and L2TP protocol .The parameters is as below
VPN IP
terminal. If there is a IP addr ess shown on ter minal ( except for 0.0. 0.0),i t means your VPN has registered
UDP Tunnel
VPN Server Addr
VPN Server Port Register to the port of VPN server
Server Group ID
Server Area Code
After VPN registered successfully, VPN server will giv e an IP a ggress to the
register to the address of VPN server
the group ID of UDP VPN
the area code of VPN server
26
L2TP
VPN Server Addr register to the address of VPN server
VPN User Name
VPN Password
UDPTunnel:
L2TP:
Enable VPN: Enable the VPN server, you must choose U DP or L2TP type in advanc e
Notice: At the present, L2TP only support L2TP VPN server under Linux, UDP only support a private UDP VPN server.
use the L2TP to visit VPN
L2TP VPN username
L2TP VPN password
use the UDP to visit VPN
Dial-Peer dial rule setting
3.6
Please refer to How to use dial rule
for detail.
27
Config Manage
3.7
Save Config: save current settings. Clear Config:
restore to default settings.
Backup Config: Backup the config file, via point the right key of mouse- save target as….-will pop a save window, then type the config file name in the File name (the file type is text file)
Update Configuration: Update the current configuration through configuration files.
Notice: clear config in admin mode, all settings restores to factory default; clear config in
guest modem, all settings except sip, advance sip restore to factory default.
28
3.8 Update
3.8.1 Update
Web Update:
Update the application or configuration files of the phone. The application document is .z format, and the configuration files is .cfg format.
Through clicking on the "browse" button to open the upgrade file or configuration file, then click on "Update" button. After the upgrade, 3300IP will automatically restart.
FTP Update:
upload/download the configure file with FTP or TFTP server, or download firmware from FTP or TFTP server
Back up configure file to your FTP/TFTP server.
configure use .cfg extension.
The Type includes two parts of config file export and config file import
Config file export: export the config file
Config file import: import the config file
3300IP phone support FTP and TFTP auto update, the gateway will auto obtain the configure file from your update server if configured. To obtain the original configure file, you can use the FTP/TFTP back up as describe above. Configure file using module structure, user may remain the concerned modules and remove other modules. Put the configure file in the root directory of update server when finish editing.
29
3.8.2 Auto Update
Current Version:
Server Address:
Username: FTP server user name
Password:
Config File Name:
Config Encrypt Key: The encrypt key of confirmation file
Protocol Type:
Update Interval Time: The interval time that the terminals search for new
configuration file.
the system will display the current version number
FTP/TFTP server address
FTP server password
The name of configuration file
The protocol type that used for upgrading
Update Mode:
auto provision mode; Disable: not auto updateUpdate after reboot:
auto update after rebootUpdate at time interval: auto update after a certain time
Configure file version was in the <<VOIP CONFIG FILE>> Version 1.0007 and <GLOBLE CONFIG MODULE> ConfFile Version
For instance:
Gateway original version is:
<<VOIP CONFIG FILE>>Version:1.0000
<GLOBLE CONFIG MODULE> ConfFile Version:6
User may edit the configure file version to:
30
<<VOIP CONFIG FILE>>Version:1.0007
<GLOBAL CONFIG MODULE> ConfFile Version7
3.9 System Manage
3.9.1 Account Manage
Set web access account or keypad password of 3300IP.
31
3.9.2 Syslog config
Set the system log
Server IP:
Server Port: set the syslog server port
MGR Log Level:
SIP Log Level:
IAX2 Log Level: set the IAX2 log level
Please click “apply” after setting
set the syslog server address
set the MGR log level
set the SIP log level
3.9.3
Phone Book
3.9.4 Time Set
This page layout is the setting of time of phone.
32
Server:
Timezone: select correct time zone in list box
Timeout:
Daylight:
SNTP: select SNTP server
12 Hours Format:
Manual Config: The time setting
type the IP address of time server
longest response time for SNTP
Daylight saving time
select 12 hours format
3.9.5 MMI SET
Set the greeting information on LCD.
3.9.6 Logout & Reboot
Logoutlogout the Web entry.
Reboot Phone:logout the entry, and reboot the phone. When u ser modify any config of the phone, it will take effect after being reb oote d, you can enter into thi s layout a nd click
33
“Reboot”. And the phone will be rebooted automatically.
Note
always save config before reboot, otherwise the setting will return to previous setting.
Reboot IP phone, some setting needs to reboot to make it works. Please
4 Operating Method for Dialing
4.1 How to dial IP Phone
Yon can make a call after bein g made a pr oper setting o n your phone. Ple ase confirm whether all the net wires are connected correctly.
If you want to make a call, you can ma ke it af ter di aling th e num ber and th en pressi ng “#”.
You can find IP address by the menu.
Modifying the IP address of the computer, and making it the same net with IP100.
Inputting the IP address of IP100 in the browser, and then you can visit the setting layout of IP100 after press the Enter key; super user account is admin/admin; common user account is guest/guest.
4.2 Set the phone being connected to server
4.2.1 Set the WAN interface
The connection ways of entering the NetworkWAN Config layout phone of the net port:
3300IP could be connected to Internet by using the static IP, DHCP IP, or PPPoE dialing.
34
Configure Static IP:
----choose static;
----fill in the IP address of 3300IP in the IP address;
----fill in the subnet mask in Netmask;
----fill in the router address or up Gateway address in the Gateway;
----fill in the local DNS server address in the Pri mary DNS and Alt er DNS respectively.
Use the configure to dynamic obtain IP to get IP address:
----choose DHCP option. Now, if the network has DHCP server, then 3300IP will get IP address, Netmask, Gateway, Primary DNS and Alter DNS from this DHCP server automatically.
Use PPPoE dialing to connect the Internet:
35
----choose PPPoE option.
----please fill in the account and password which PPPoE have dialed in the PPPoE Username and Password. So 3300IP could connect the Internet through PPPoE d ialing, and automatically get IP address, Netmask, Gateway, Primary DNS and Alter DNS and so on .
4.2.1 SIP
setting
Enter into the information:
Register Server Addr:
Register Server Port:
Register Username:
phone number)
VoIP  SIP Config
to set the layout config and sip account
Register address of public SIP server
Register port of public SIP server
Username of your SIP account (Always the same as the
default port is 5060
36
Register Password:
Phone Number: Phone number of your SIP account
----choose Enable Register You can dial VoIP phone when the WAN interface and IAX protocol are being set correctly .
Password of your SIP account.
4.2.2 IAX setting
IAX Server Addr:
IAX Server Port:
Account Name:
number)
Account Password: Local port: Phone Number:
----choose Enable Register
----if you use IAX account to m ake a call, please choose IAX(Deault Protocol), if you fail to choose it, then you can use SIP account to make a call again.
----if you use G..729 to arrange it ,please choose Enable G..729 You can dial VoIP phone when the WAN interface and IAX protocol are being set correctly .
Note:
please choose Save Config in the Config Manage after setting the information, or
the existing setting information will be failed after rebooting..
How to use the dial rule?
4.3
3300IP provide flexible dial rule, with different dial-rule configure, user can easily
Register address of public IAX server Register port of public IAX serverdefault port is 4569 Username of your SIP account (Always the same as the phone
Password of your IAX account.
Signal port of local, default port is 4569
Phone number of your IAX account
37
implement the following function:
----Replace, delete or add prefix of the dial number.
----Make direct IP to IP call
----Place the call to different servers according the prefix.
You can click “Add” to add a new dial rule. Below is the detail setting of the dial-rule:
Phone Number:
The Number suit for this dial rule, can be set as full match or prefix match. Full match means that if the number user dialed is completely the same as this number, the call will use t his di al-r ule. Prefix match means that if prefix of the number that the user dials is the same as the prefix, the call will use this dial-rule, to distinguish from the full match case, you need to add “T” after the prefix number in the phone number setting.
Call Mode:
support SIP.
Destination (optional): call destination, can be IP or domain. Default is 0.0.0.0, in
this case the call will be routed to the Public SIP server. If you set the destination to
255.255.255.255, then the call will be routed to the private SIP server. Also you can key other address here to make direct IP calls
Port (optional):
Configure the port of the destination, default is 5060 in SIP
Alias (optional):Set up the Alias. We support four Alias as below. Alias need to
co-work with the Del Length:
add:xxx, add prefix to the phone number, can set to reduce the dial length. all: xxx, replace the phone number with the xxx, can use as speed dial function. del, delete the first N numbers. N is set in the Del Length
rep:xxxreplace the first N numbers. N is set in the Del Length. For Example: Use wants to place a call 86633-8215555, then you can set the phone number in the dial rule as 0633T, and set the Alias as rep:86633, and set the Del Length to 4. Then all calls begin with 0633 will be changed to 86633 xxxxxxxx.
Suffix (optional):
Configure suffix, show no suffix if not set
Instance:
38
2T rule
sent to private SIP server.
3T rule: If the call starts with 3, the first 3 w ill be deleted, and the rest num b er with be
sent to public SIP server.
123 rule: Dial 123 and will send 06332221015 to your server. Used as speed dial
function.
0T rule
dial 06332221015 and AG-188 will send 866332221015 to your server.
11 rule
without set up a sip server.
: If the call starts with 2, the first 2 will be deleted, and the rest number will be
: If the calls is begin with 0, the first 0 will be replace by 86. Means that if you
: when you dial 11, the call with send to 192.168.0.11, suit for LAN application
4.4 Voice mail
When there is a mail, voice mail LED would be flickering, and LC D would display “New message”. After listening the message , voice mail LE D would stop flickering, and “New message” would disappear from LCD.
39
Loading...