The DIALOG® 3G endpoint (DTMW) is an RF transceiver used
to communicate metered consumption data in Automatic Meter
Reading (AMR) systems.
Begin
3G features an exclusive design that completely encapsulates
the encoder electronics, transceiver, antenna, and batteries
under the register glass. A design called ConnectionFree™.
Chapter 1.
Getting Started
Chapter 2.
Installing the
Hypertext links are blue.
Provides an overview of the DTMW
endpoint installation, including installation
options, siting, and required tools.
Provides step-by-step instructions for wiring
the endpoint to a register and installing the
endpoint using the rod mount, on a wall or
similar surface, or on a pipe.
Se e C on te nt s o n pa ge i ii f or
th e c om pl et e t ab le o f
co n te nt s
CAUTION: The User and the Installer should be aware that changes and modifications to the equipment
not expressly approved by Master Meter could void warranty and the user's authority to operate the
equipment.
Professionally trained personnel should install the equipment.
The antenna used for this transmitter must be installed to normally provide minimum separation distance
of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other
antenna or transmitter
ATTENTION! This type of note is used to warn of potential physical harm to the user or hardware. It is
critical that you pay strict attention to WARNING notes, read the information carefully, and heed the
advice/instructions.
4
Page 5
Cautionary
Note on
Repairs &
Modifications
ATTENTION!:
Attempts to repair a 3G endpoint by unauthorized personnel (any one
other than a Master Meter factory certified professional) may subject
the person to shock hazard scenario if removal of protective covers is
attempted. Unauthorized repair may void the warranty and/or
maintenance contract with your company.
ATTENTION!:
This unit cannot be modified and is not repairable. Modification of this
device could cause non-compliance with FCC rules. Attempts to
modify this device will void the warranty.
ATTENTION!:
Follow these procedures to avoid injury to yourself or others.
5
Page 6
Id e nt if ic at io n
General Admin
TrademarkNotice
Tr a de ma rk N ot i ce
PatentNotice
Pa te nt N ot ic e
ComplianceStatement
Co m pl ia nc e St a te me nt
Tr a ns mi ss io n Du ty Cy cl e
DTMW - 3G Endpoint Installation Guide
3G is a registered trademark of Master Meter, Inc. All other product names
and logos in this document are used for identification purposes only and
may be trademarks or registered trademarks of their respective companies.
3G intellectual property is protected by US and foreign patents, and/or
patents pending.
The digital portion of the transceiver has been tested and found to comply with
the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and can
radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the
following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help
This device complies with Part 15 of FCC Rules. Operation is subject to the
following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including
interference that may cause undesired operation
The transmission duty cycle is limited by its design not to exceed 1.0%
6
Page 7
Tr a ns po rt at io n Cl a ss if ic at io n
Pr o du ct R et u rn
Do c um en t Id ea s & S u gg es ti o ns
The Federal Aviation Administration prohibits operating transmitters and
receivers on all commercial aircraft. When activated, endpoints are
considered operating transmitters and receivers and cannot be shipped by
air.
To comply with FCC, UN, and Department of Transportation regulations, all
units must be returned in their original packaging following Master Meter’s
Return Material Authorization (RMA) process.
We want to hear your ideas on how we might improve and add value to this
document. If you have comments or suggestions on how we may improve
this document, send them to: