TeleEye R X S er i es
Video Recording Trans m it t er
RX364
RX368
RX361 6
User Guide
Notice:
Signal Communications Limited reserves the right to make improvements to the product
described in this manual at any time and w ithout prior notice.
This manual is copy righted. A ll rights are reserved. This manual should not be copied,
reproduced or translated in w hole or part w ithout prior consent f rom Signal Communications
Limited.
TeleEye is a trademark of Signal Communications Limited and is registered in China,
European Communities, H ong K ong, US and other countries.
A ll other trademarks are the property of their respective ow ners.
Copy right (c) 2006 Signal Communications Limited (A member of TeleEye G roup). A ll
rights reserved.
Release Version 2.01.01
L im its of L ia b il ity a n d D is cl a im er of W a r r a n ty
Signal Communications Limited has taken care in preparation of this manual, but makes
no expressed or implied w arranty of any kind and assume no responsibility f or errors or
omissions. N o liability is assumed f or incidental or conseq uential damages in connection w ith
or arising out of the use of the inf ormation or accessories contained herein.
Features and specif ications are subj ect to change w ithout prior notice.
Table of Contents
S E C T I O N 1 1
Introduction 1
A . Introduction 1
B . F e a ture s 2
C . R e m o v ing th e P a ck a g e s 3
D . C onv e ntion U s e d in T h is M a nua l 3
E . F ront P a ne l D e s crip tion 3
F . R e a r P a ne l D e s crip tion 6
S E C T I O N 2 9
H a rd D is k Ins ta l l a tion, F orm a tting a nd S ca nning 9
A . H a rd D is k Ins ta l l a tion 9
B . F orm a t H a rd D is k 12
C . S ca n D is k 15
S E C T I O N 3 16
B a s ic Ins ta l l a tion f or L oca l a nd R e m ote M onitoring 16
A . S e tup TeleEye R X f or L oca l C C T V M onitor 16
B . S e tup TeleEye R X f or L A N C onne ction w ith S ta tic IP 19
C . S e tup TeleEye R X f or B roa db a nd or N a rrow b a nd Inte rne t C onne ction w ith S ta tic IP 29
D . S e tup TeleEye R X f or B roa db a nd or N a rrow b a nd Inte rne t C onne ction w ith D y na m ic IP 38
E . S e tup TeleEye R X f or M ode m C onne ction 4 8
S E C T I O N 4 5 7
B a s ic O p e ra tion f or L oca l a nd R e m ote M onitoring 5 7
A . L oca l C C T V M onitor : L iv e M onitoring , R e cording a nd P l a y b a ck 5 7
B . TeleEye R X R e ce p tion S of tw a re W X - 30 : L iv e M onitoring , R e cording a nd P l a y b a ck 60
S E C T I O N 5 64
O S D M e nu O p e ra tion 64
A . H ow to us e O S D m e nu 64
B . M a in M e nu 65
C . R e cording L og M e nu 8 3
D . P T Z M e nu 8 5
E . R e cording M e nu 8 5
F . E v e nt M e nu 8 6
S E C T I O N 6 92
A dv a nce d O p e ra tion 92
A . Ins ta l l TeleEye R X w ith A l a rm S e ns ors a nd R e l a y C ontrol P ort 92
B . Ins ta l l TeleEye R X w ith T a m p e r C ircuit a nd E x te rna l R e s is tors 94
C . T h roug h p ut C ontrol 97
D . E v e nt H a ndl ing 98
E . E v e nt A ction 119
F . P a s s w ord 132
G . B uil t- In W e b S e rv e r 133
H . B a ck up to C D - R 136
I. C onne ction w ith P T Z ca m e ra s 138
J . P a ne l K e y L ock 14 1
K . T im e S y nch roniz a tion 14 2
A P P E ND I X A 143
S a f e ty Ins truction 14 3
A P P E ND I X B 144
L im ite d W a rra nty 14 4
A P P E ND I X C 145
s u r e L IN K T e ch nol og y 14 5
A P P E ND I X D 149
F irm w a re U p g ra de 14 9
A P P E ND I X E 15 0
G e ne ra l T e rm s D is cus s ion 15 0
A P P E ND I X F 15 1
A udit T ria l L og D e s crip tion 15 1
A . A udit T ria l L og de s crip tion of s e tting l og a nd op e ra tion l og 15 1
B . S e tting L og O p e ra tion C ol um n T a b l e 15 1
C . O p e ra tion L og O p e ra tion C ol um n T a b l e 15 3
A P P E ND I X G 15 4
H a rd D is k R e com m e nda tion L is t 15 4
A P P E ND I X H 15 5
S p e cif ica tions 15 5
Tele Eye RX U s er G u i d e
P a g e 1
SECTION 1
In t r o d u c t i o n
A. I n t r o d u c t i o n
TeleEye R X Series Video Recording Transmitter operates w ith its revolutionary multi-
rate video coder to f ulf ill the highest video coding req uirements f or simultaneous transmission
and recording. Seamless video transmission by TeleEye R X can be perf ormed in low and
medium bandw idth communication netw orks including A DSL, I SDN and PSTN ; w hilst
DVD-q uality videos can be transmitted through LA N and recorded into local hard drive w ith
optimum speed at 50/ 60f ps and resolution in D1 resolution. Real time recording of up to
200/ 240f ps on all video channels can also be achieved at CI F resolution.
TeleEye R X provides prof essional and real lif e security control of premises w ith its
sophisticated event management scheme. I t responses to w ide range of events triggered by
external alarm sensor, video motion, pow er interruption and tamper. There is an arm/ disarm
control f or the event management mechanism. Every external alarm input is conf igurable w ith
an individual entry / exit delay , f ire z one and tamper detection setting. Various actions like
sending video back to a designated receiving PC, video recording, email notif ication, etc.
TeleEye R X can also keep a comprehensive log of the events f or audit trail.
TeleEye R X is designed to f ully comply w ith the British Standard BS 8418:2003,
providing prof essional remote monitoring and visual alarm verif ication solution to central
monitoring station.
W ith a built-in CD-w riter, video f ootage stored inside TeleEye R X can be easily extracted
f or evidential purposes. Recorded video can be backed up in CD and play ed back in any PC
w ithout any special sof tw are.
In t r o d u c t i o n
Tele Eye RX U s er G u i d e
B . F e a t u r e s
H a r d w a r e F e a t u r e
Video recording w ith rate up to 100/ 120f ps (RX 364), 200/ 240f ps (RX 368 & RX 3616)
Remote and standalone operations
Composite video output w ith O SD menu
SM A C-M multi-rate video coding technology
Real time video transmission
Up to 60f ps (RX 364), 120f ps (RX 368 & RX 3616) over LA N f or N TSC
Up to 50f ps (RX 364), 100f ps (RX 368 & RX 3616) over LA N f or PA L
Excellent picture resolution
Up to 720 x 480 pixels f or N TSC
Up to 720 x 576 pixels f or PA L
4 (RX 364)/ 8 (RX 368) / 16 (RX 3616) video inputs w ith one video output
1 (RX 364)/ 2 (RX 368 & RX 3616) audio inputs
1 audio output and 1 public addressing (P.A .)output
4 relay sw itches and 4 (RX 364) / 8 (RX 368) / 16 (RX 3616) alarm inputs
4 additional detection inputs
Removable hard disk
Built-in CD w riter
P a g e 2
F u n c t i o n a l F e a t u r e
sureL I N K , support both static and dy namic I P
Sophisticated event management
Sy stem arm/ disarm
Flexible connections: LA N , A DSL, PSTN , I SDN , mobile netw ork, etc.
Triplex operation: simultaneous video monitoring, recording & play back
Video motion detection
Event-driven recording
Pre- & post-event video recording
Entry / exit z one conf igurable on all alarm inputs
A uto alarm dialback
Connection authentication
Compatibility w ith popular telemetry protocols
Single-site monitoring
W eb-based video monitoring
Programmable video recording
Data retention
In t r o d u c t i o n
Tele Eye RX U s er G u i d e
C . R e m o v i n g t h e P a c k a g e s
A f ter removing the package, make sure y ou have the f ollow ing items:
TeleEye R X Video Recording Transmitter w ith Built-in CD W riter
H ard Disk Cartridge A ccessories (K ey x 2 and Screw x 4)
User G uide
W arranty Card
Registration Code Sheet
H DD Recommendation List
Sof tw are CD
Pow er A daptor and Pow er Cord
A larm Port Connector (37 Pins) & A larm Port Cover
Resistors (1.2kΩ x 20, 6kΩ x 20)
Straight-through Ethernet Cable
D . C o n v e n t i o n U s e d i n T h i s M a n u a l
“ ” : Buttons on the TeleEy e RX transmitter f ront panel
{ } : H ardw are I tems on the TeleEy e RX transmitter besides buttons
[ ] : O SD menu or M S W indow s menu
( ) : Ref ers to other section or page
P a g e 3
E . F r o n t P a n e l D e s c r i p t i o n
Re m o v a b l e H a r d D i sk Ca r t r i d g e
{ Key L ock } and { Key } are provided to lock the hard disk f rom unauthoriz ed removing
and also be used to sw itch O N / O FF the sy stem
L i v e Ca m e r a Co n t r o l Bu t t o n s
For RX 364 (1-4), RX 368 (1-8), RX 3616 (1-16)
“C a m er a C on tr ol ” f ast sw itch to a specif ic camera f or local monitoring
Bu i l t - i n CD W r i t e r
I t allow s user to back up video to CD-R or CD-RW (M ax siz e of 650 M B)
In t r o d u c t i o n
Tele Eye RX U s er G u i d e
S c r e e n Mo d e Co n t r o l
P a g e 4
Fo r R X 364
Fo r R X 368
Fo r R X 3616
Full, Q uad, 3 x 3, H ex screen mode:
The sy stem w ill display one, f our, eight, sixteenth
screens decided on the button pressed. Seq uential
mode w ill also disable.
Seq uential mode* * :
The seq uential button enables the seq uential page
mode of live monitoring. I n seq uential mode, screen
mode can be changed by pressing the seq uential
button again.
* * I n FULL screen seq uential mode, the camera
seq uence can be set on user’s pref erence.
(M ain M enu --- Setup --- Video --- Local monitoring
--- Seq uential Cams)
Me n u Co n t r o l Bu t t o n s / L o c a l P l a y b a c k Co n t r o l Bu t t o n s / P T Z Co n t r o l
S u m m a r y o f C o n t r o l B u t t o n
Buttons M enu M ode Play back M ode PTZ M ode
Cursor Up Pause Tilt Up
Cursor Dow n Stop Tilt Dow n
Cursor Lef t Rew ind Pan Lef t
Cursor Right Forw ard Pan Right
Enter Play Z oom I n
Pervious Page Back/ Stop Z oom O ut
In t r o d u c t i o n
Tele Eye RX U s er G u i d e
Mo d e Co n t r o l Bu t t o n s a n d L E D
These 5 buttons are used f or sw itching betw een the control modes
“E v en t” button : Pop up event menu
“Rec” button : Enable/ disable normal or scheduled recording
“L iv e” button : View live video at any time and PTZ control in live mode
“S ea r ch ” button : Play back log menu
“M en u ” button : Sy stem settings and other sy stem operations
N o t i f i c a t i o n L E D s
P a g e 5
There are 5 notif ication LEDs, 2 red colors and 3 blue colors f rom lef t to right.
{ E v en t L E D }
{ Recor din g L E D }
{ L iv e L E D }
{ S ea r ch L E D }
{ M en u L E D }
{ P ow er L E D }
: Blinks w hen event is triggered
: I s O N w hen the transmitter is recording
: I s O N during live monitoring
: I s O N w hen the sy stem is in play back mode
: I s O N w hen the sy stem is in menu mode
: I s O N continuously w hen the sy stem is pow ered up
In t r o d u c t i o n
Tele Eye RX U s er G u i d e
F . R e a r P a n e l D e s c r i p t i o n
RX3 6 4 :
10 6 5 4 3 21
789
RX3 6 8
10 6 5 4 3 2 1
P a g e 6
789
RX3 6 16
10 6 5 4 3 2 1
789
In t r o d u c t i o n
Tele Eye RX U s er G u i d e
1. V ideo O u tp u t C on n ector s
A composite video signal w ith 1V p-p is output f rom this connector
PA L/ CCI R f ormat w ith 625 lines, 25 f rames per second
N TSC/ EI A f ormat w ith 525 lines, 30 f rames per second
2. V ideo I n p u t C on n ector
{ Standard BN C connectors} f or video source input
A composite video source f rom camera should be supplied to these connectors
CH 1 – CH 4 (RX 364)
CH 1 – CH 8 (RX 368)
CH 1 – CH 16 (RX 3616)
3. A u dio I n / O u t P or t
{ A udio I n} : Connect audio input device (e.g. microphone) w ith RCA j ack to
TeleEye R X transmitter f or recording. (O nly 1 { A udio I n} f or RX 364)
{ A udio O ut} : Connect audio output device (e.g. speaker) w ith RCA j ack to TeleEye
R X transmitter and generate output audio signal
{ A udio PA } : Connect audio output device (e.g. speaker) to Tele Eye R X transmitter
and generate audio signal to f acilitate remote public addressing
P a g e 7
4. E th er n et S ock et ( 10 / 10 0 B a s e- T )
This socket is used f or connecting TeleEye R X to the corporate computer netw ork
(e.g. LA N )
This socket includes { C O L L E D } and { L I NK L E D }
{ C O L L E D } : W hen O N , indicates that collision is occurring on the netw ork
{ L I NK L E D } : W hen O N , indicates that TeleEye R X is connecting to the netw ork
and ready to f unction
5. U S B
For support use only
6. RS 2 3 2 ( M odem ) P or t
A { DB-9 M ale Connector} of DTE f ormat, capable f or connecting to DCE such as
modem, I SDN terminal adapter
P i n n u m b er D ef i n i t i o n D i r ec t i o n
1 C D I n p u t
2 R X D I n p u t
3 T X D O u t p u t
4 D T R O u t p u t
5 G N D – – –
6 D S R I n p u t
7 R T S O u t p u t
8 C T S I n p u t
9 – – –
In t r o d u c t i o n
Tele Eye RX U s er G u i d e
7. RS 48 5 I n / O u t P or t
{ I n} : 2-w ay terminal block f or connecting a key board controller to TeleEye R X
transmitter in order to control a PTZ camera
{ O ut} : 2-w ay terminal block f or connecting a PTZ camera
8. Rel a y O u t / A l a r m I n P or t
4 relay (also call sw itch) output
TeleEye RX 364: 4 alarm input
TeleEye RX 368: 8 alarm input
TeleEye RX 3616: 16 alarm input
A ll alarm ports are N C/ N O ty pe and none/ SEO L/ DEO L tamper ty pe input
A ll relay ports are latching/ push-button ty pe output
9. P ow er
Connect pow er supply (12V DC) to TeleEye R X transmitter
10. S w itch
Sw itch on or of f the TeleEye R X transmitter
P a g e 8
In t r o d u c t i o n
Tele Eye RX U s er G u i d e
P a g e 9
SECTION 2
H a r d D i s k In s t a l l a t i o n ,
F o r m a t t i n g a n d S c a n n i n g
A. H a r d D i s k I n s t a l l a t i o n
TeleEye R X transmitter supports A T A standard hard disk. User should use the hard disk listed
at the hard disk recommendation list on A ppendix E.
Recommendation: The hard disk is suggested to set in M a s ter M ode. For details please ref er to
the hard disk case or its manual.
H a r d D i sk F r o n t P a n e l D e sc r i p t i o n
K ey Lock Description
1. H DD activity indicator
2. Pow er indicator
3. A ctive-handle
4. H andle
5. Cartridge f rame
6. K ey lock
H a r d D i sk In st a l l a t i o n , F o r m a t t i n g a n d S c a n n i n g
Tele Eye RX U s er G u i d e
In st a l l a t i o n P r o c e d u r e
R X M UST be shut dow n bef ore install / uninstall hard disk
P a g e 10
1. Press “M en u ”
2. [S H U T D O W N] menu w ill pop up and select [S H U T D O W N] option and press “E n ter ”
button.
3. Select [Y E S ] and press “E n ter ”
[I T I S NO W S A F E T O T U RN O F F R X ].
4. Pull the active-handle outw ards. Then use the
bundled key provided and insert into the
key hole. Turn the key anti-clockw ise (position
C), then y ou can pull out the handle.
5. Pull the handle outw ards to remove the carrier
body aw ay f rom the cartridge f rame.
6. Push the release latch to slide the top cover
backw ards and remove.
button, select [S H U T D O W N] option and press “E n ter ” button.
button to conf irm the shut dow n and w ait f or the message
H a r d D i sk In st a l l a t i o n , F o r m a t t i n g a n d S c a n n i n g
Tele Eye RX U s er G u i d e
cl ock w is e
7. I nsert the DC pow er cable and I DE cable on the
H DD
8. Position the H DD into carrier body and secure
the H DD using the f our screw s provided.
P a g e 11
9. Slide the top cover back to the carrier body by
sliding f orw ard to secure.
10. Slide the carrier body back into the cartridge
f rame and push carrier body f urther into
cartridge f rame until f u l l y in s er ted.
11. Pull the active-handle outw ards, then use the
bundled key and insert into the key hole, turning
the key
(position A ) to secure the
handle.
H a r d D i sk In st a l l a t i o n , F o r m a t t i n g a n d S c a n n i n g
Tele
Eye
R X
[I NC O RRE C T D I S K
F O RM A T ]
[Y E S ]
[F O RM A T D I S K]
[S C A N D I S K]
SCAN DISK
Tele Eye RX U s er G u i d e
\ SCANNING 9 0 %
B . F o r m a t H a r d D i s k
Format H ard disk w ill erase all data in the hard disk and reconstruct it so that it is readable by
TeleEye R X transmitter. Y ou must f ormat the hard disk af ter installed a new hard disk to
TeleEye R X transmitter.
Formatting w ill be used if the hard disk f ormat is N O T TeleEye R X transmitter recogniz ed
f ormat. Usually , it is a new hard disk, or a hard disk not used by TeleEye R X transmitter.
P r o c ed u r e
INCO R R E CT DISK F O R M AT
F O R M AT NO W ?
Y E S NO
P a g e 12
1. A f ter starting up
transmitter, O SD
menu w ill pop up
menu. Select
option and press
“E n ter ” button to f ormat the hard disk.
F O R M AT DISK
\ F O R M AT T ING 9 0 %
2.
message board w ill pop up to
show about the status
3. A f ter f inishing f ormat process,
processing board w ill pop up to show the scanning
status. The transmitter w ill restart.
H a r d D i sk In st a l l a t i o n , F o r m a t t i n g a n d S c a n n i n g
M AIN M E NU
SCAN / F O R M AT DISK
F O R M AT DISK
AL L DAT A IN DISK
Tele Eye RX U s er G u i d e
W IL L B E E R ASE D ,
SU R E T O P R O CE E D ?
Y E S NO
P a g e 13
Ma n u a l F o r m a t t i n g
I t w ill be used if user w ants to f ormat the hard disk so as to have a clean recording space and
redeem the f ile allocation.
SE T U P . . .
B ACKU P T O CD- R . . .
SW IT CH CO NT R O L . . .
SCAN / F O R M AT DISK . . .
T R ANSM IT T E R INF O . . .
L O CK KE Y S E NT E R
SH U T DO W N E NT E R
M AST E R H DD
M O DE L NO M AX T O R X X X X
SE R IAL NO X X X X X X X
CAP ACIT Y 4 1 G B
SL AV E N/ A
M O DE L NO
SE R IAL NO
CAP ACIT Y
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - DISK U SAG E 5 2 %
SCAN DISK E NT E R
F O R M AT E NT E R
1. Press “M en u ”
button, select [S C A N/ F O RM A T
D I S K] option and press “E n ter ” button to enter
[S C A N/ F O RA M A T D I S K] sub menu.
2. Select [F O RM A T ] option press “E n ter ”
button
3. Select [Y E S ] option and press “E n ter ” button
and [F O RM A T D I S K] board w ill pop up to show
about hard disk f ormat processing status
4. Press “E n ter ” button to restart transmitter
w hen [F O RM A T F I NI S H E D ] message board
H a r d D i sk In st a l l a t i o n , F o r m a t t i n g a n d S c a n n i n g
F O R M AT
F O R M AT F INISH E D ,
SY ST E M W IL L R E ST AR T NO W
Tele Eye RX U s er G u i d e
O K
pops up.
P a g e 14
H a r d D i sk In st a l l a t i o n , F o r m a t t i n g a n d S c a n n i n g
SCAN DISK
SCAN / F O R M AT DISK
F O R M AT
E NT E R
AL L R E CO R DING W IL L ST O P
Tele Eye RX U s er G u i d e
DU R ING SCANDISK
SU R E T O P R O CE E D ?
Y E S NO
P a g e 15
C . S c a n D i s k
I t is a hard disk maintenance f unction w hich similar to Scan Disk f unction provided by the
O perating Sy stem of y our personal computer. TeleEye R X transmitter provides this f unction in
an attempt to rescue the hard disk w hen errors are f ound, and to enhance its perf ormance and
reliability .
P r o c ed u r e
M AIN M E NU
SE T U P . . .
B ACKU P T O CD- R . . .
SW IT CH CO NT R O L . . .
SCAN / F O R M AT DISK . . .
T R ANSM IT T E R INF O . . .
L O CK KE Y S E NT E R
SH U T DO W N E NT E R
1. Press “M en u ”
D I S K] option and press “E n ter ” button to enter
[S C A N/ F O RA M T D I S K] sub menu.
button, select [S C A N/ F O RM A T
There is inf ormation about the hard disk. I f not,
please check that the hard disk is installed properly .
2. Select [S C A ND I S K] option press “E n ter ”
button.
3. Select [Y E S ] option and press “E n ter ” button to
start the [S C A ND I S K] process.
M AST E R H DD
M O DE L NO M AX T O R X X X X
SE R IAL NO X X X X X X X
CAP ACIT Y 4 1 G B
SL AV E N/ A
M O DE L NO
SE R IAL NO
CAP ACIT Y
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - DISK U SAG E 5 2 %
SCAN DISK E NT E R
H a r d D i sk In st a l l a t i o n , F o r m a t t i n g a n d S c a n n i n g
Tele Eye RX U s er G u i d e
R G 5 9 ca b l e
B a s i c In s t a l l a t i o n f o r L o c a l a n d
R e m o t e M o n i t o r i n g
A. S e t u p TeleE y e R X f o r L o c a l C C T V M o n i t o r
C o n n ec t i o n T o p o l o g y
VIDEO OUT: Connect to
P a g e 16
SECTION 3
m oni tor w i th R G 5 9 ca b l e
CCTV
Moni tor
R G 5 9 ca b l e
P ow er A d a p ter
VIDEO IN : Connect to
ca m er a s w i th R G 5 9 ca b l e
a nd B N C connector
TeleEye R X
Ca m er a s
**For RX368/RX3616, t h e “VIDEO OUT” p ort i s on t h e ri g h t s i d e of “VIDEO IN ” **
E q u i p m e n t
TeleEye R X Transmitter
Cameras
Video Cables (RG -59) w ith BN C H eader
CCTV M onitor
B a s i c I n s t a l l a t i o n f o r L o c a l a n d R em o t e M o n i t o r i n g
Tele Eye RX U s er G u i d e
P a g e 17
S e t u p P r o c e d u r e
1. Connect cameras to TeleEye R X { V ideo I n p u t} w ith RG 59 cable and BN C connector.
N ot e : T h e c a me ra s y s t e m i s e i t h e r N TS C or P A L a n d s u p p os e s a l l c a me ra s u s e t h e S A M E
s y s t e m f orma t .
2. Connect CCTV monitor to TeleEye R X { V ideo O u tp u t} w ith RG 59 cable and BN C
connector.
3. I nstall and use the bundled key to lock the { H a r d D is k Ra ck } w ith hard disk to the
TeleEye R X .
N ot e : I f t h e re i s n o h a rd d i s k i n s t a l l e d , Re c ord i n g a n d P l a y b a c k a re n ot f u n c t i on a l
4. Plug in the pow er adapter (12V DC) to TeleEye R X .
5. Turn on the pow er of TeleEye R X , camera and monitor. Check the { P ow er L E D }
w hich is lit up in blue color continuously at TeleEye R X f ront panel af ter pow er on. A f ter
several seconds, live video appears on the CCTV monitor as f ollow s:
N ot e : P l e a s e g o t h rou g h t h e f ol l ow i n g s t e p s ( 6- 10 ) i f C C T V mon i t or d oe s n ot s h ow v i d e o c l e a rl y
B a s i c I n s t a l l a t i o n f o r L o c a l a n d R em o t e M o n i t o r i n g
Tele Eye RX U s er G u i d e
SE T U P M E NU
R E ST O R E F ACT O R Y SE T T ING
E NT E R
V IDE O
P a g e 18
6. Press the “M en u ”
button to pop up the [M A I N
M E NU ] on O SD.
7. Use “U p ” or “D ow n ” button to select
[S E T U P ] option and press “E n ter ” button to
enter the [S E T U P ] sub-menu.
8. Use “U p ”
or D ow n ” button to select
[V I D E O ] option and press “E n ter ” button to
enter the [V I D E O ] sub-menu.
M AIN M E NU
SE T U P . . .
B ACKU P T O CD- R . . .
SW IT CH CO NT R O L . . .
SCAN / F O R M AT DISK . . .
T R ANSM IT T E R INF O . . .
L O CK KE Y S E NT E R
SH U T DO W N E NT E R
V IDE O . . .
R E CO R DING . . .
SW IT CH E S . . .
DAT E / T IM E . . .
CO NNE CT IO N . . .
E V E NT H ANDL E R . . .
T R ANSM IT T E R . . .
P ASSW O R D . . .
9. Select [V I D E O F O RM A T ] and press “L ef t”
or “Rig h t” button to set either [NT S C ]
or [P A L ] option. (A ll cameras should have the
same video f ormat).
10. Y ou can alw ay s press “L iv e” button to exit any
menu operation and start live monitoring.
CAM E R A SE T T ING . . .
L O CAL M O NIT O R ING . . .
O SD CO L O R B L U E
V IDE O F O R M AT P AL
B a s i c I n s t a l l a t i o n f o r L o c a l a n d R em o t e M o n i t o r i n g
Tele Eye RX U s er G u i d e
R G 5 9 ca b l e
S ock et
N etw or k s w i tch
P a g e 19
B . S e t u p TeleE y e R X f o r L AN C o n n e c t i o n w i t h S t a t i c
I P
C o n n ec t i o n T o p o l o g y
VIDEO OUT: Connect to
m oni tor w i th R G 5 9 ca b l e
a nd B N C connector
CCTV
M oni tor
VIDEO IN : Connect to
ca m er a s w i th R G 5 9 ca b l e
a nd B N C connector
TeleEye R X
Eth er net
P ow er A d a p ter
S tr a i g h t-th r ou g h Eth er net ca b l e
R G 5 9 ca b l e
Ca m er a s
**For RX368/RX3616, t h e “VIDEO OUT” p ort i s on t h e ri g h t s i d e of “VIDEO IN ” **
Eq u i p m en t
TeleEye R X Transmitter
N etw ork Sw itch
Straight-through Ethernet Cable (bundled)
Cross-over Ethernet Cable
Cameras
Video Cables (RG -59) w ith BN C H eader
CCTV M onitor
CD RO M w ith W X -30 Sof tw are (bundled) (f or PC operation only )
PC
P C R eq u i r em en t s
C P U : Pentium I V 2.4 G H z or above
RA M : 512 M B or above
D is p l a y : 1024 x 768, true color or better
O S : M S W indow s 2000, X P
H D D : 1G B of f ree disk space or above
B a s i c I n s t a l l a t i o n f o r L o c a l a n d R em o t e M o n i t o r i n g
Tele Eye RX U s er G u i d e
P a g e 20
S et u p P r o c ed u r e
1. Connect cameras to TeleEye R X { V ideo I n p u t} w ith RG 59 cable and BN C connector.
N ot e : T h e c a me ra s s y s t e m i s e i t h e r N TS C or P A L a n d s u p p os e s a l l c a me ra s u s e t h e S A M E
s y s t e m f orma t .
2. Connect CCTV monitor to TeleEye R X { V ideo O u tp u t} w ith RG 59 cable and BN C
connector.
3. I nstall and use the bundled key to lock the { H a r d D is k Ra ck } w ith hard disk to the
TeleEye R X .
N ot e : I f t h e re i s n o h a rd d i s k i n s t a l l e d , Re c ord i n g a n d P l a y b a c k a re n ot f u n c t i on a l
4. Connect the pow er adapter (12V DC) to the TeleEye R X .
5. Turn on the pow er of TeleEye R X , camera and monitor. Check the { P ow er L E D }
w hich is lit up in blue color continuously at TeleEye R X f ront panel af ter pow er on. A f ter
several seconds, live video appears on the CCTV monitor as f ollow s:
N ot e : P l e a s e g o t h rou g h t h e f ol l ow i n g s t e p s ( 6- 10 ) i f t h e v i d e o of C C T V mon i t or d oe s n ot s h ow
B a s i c I n s t a l l a t i o n f o r L o c a l a n d R em o t e M o n i t o r i n g
c l e a rl y .
Tele Eye RX U s er G u i d e
V IDE O
SE T U P M E NU
V IDE O . . .
R E CO R DING . . .
SW IT CH E S . . .
DAT E / T IM E . . .
CO NNE CT IO N . . .
E V E NT H ANDL E R . . .
T R ANSM IT T E R . . .
L O CK KE Y S E NT E R
DIAG NO ST IC . . .
R E ST O R E F ACT O R Y SE T T ING E NT E R
P a g e 21
6. Press the “M enu”
button to pop up the [M A I N
M E NU ] on O SD.
7. Use “U p ” or “D ow n ” button to select
[S E T U P ] option and press “E n ter ” button to
enter the [S E T U P ] sub-menu.
8. Select [V I D E O ] option and press “Enter” button
to enter the [V I D E O ] sub-menu
CAM E R A SE T T ING . . .
L O CAL M O NIT O R ING . . .
O SD CO L O R B L U E
V IDE O F O R M AT P AL
9. Select [V I D E O F O RM A T ] and press “L ef t” or
“Rig h t” button to set either [NT S C ] or [P A L ]
option. (A ll cameras should have the same video
f ormat).
10. Y ou can alw ay s press “L iv e” button to exit any
menu operation and start live monitoring.
11. Conf igure T e le Eye R X transmitter I P setting
Setup TeleEye R X transmitter I P through CCTV monitor, please go to step 11a.
Setup TeleEye R X transmitter I P through PC, through PC, please go to step11b.
11.a.1 Conf igure TeleEye R X transmitter I P setting through CCTV M onitor
B a s i c I n s t a l l a t i o n f o r L o c a l a n d R em o t e M o n i t o r i n g
Tele Eye RX U s er G u i d e
RG59 cable
192.168.0.2
[C O NNE C T I O N]
SE T U P M E NU
CO NNE CT IO N
TeleEye R X
P a g e 22
E t h er n et
P o w er A d ap t er
V IDE O . . .
R E CO R DING . . .
SW IT CH E S . . .
DAT E / T IM E . . .
CO NNE CT IO N . . .
E V E NT H ANDL E R . . .
T R ANSM IT T E R . . .
L O CK KE Y S E NT E R
DIAG NO ST IC . . .
R E ST O R E F ACT O R Y SE T T ING E NT E R
S o ck et
RG59 cable
11.a.2 Press the “M en u ” button such that the O SD
main menu opens on the monitor.
C am er as
C C T V
M o n i t o r
11.a.3 Use “U p ”
or “D ow n ” button to select
[S E T U P ] option and press “E n ter ” button to
enter [S E T U P ] sub menu.
11.a.4 Select
option and press
“E n ter ” button to enter connection setting
menu.
T CP / IP …
M O DE M …
T H R O U G H P U T …
11.a.5 Select [T C P / I P ] option and Press “E n ter ”
button
11.a.6 Select [I P ] option and press “E n ter ”
button. I P address consists of f our f ields. Each
B a s i c I n s t a l l a t i o n f o r L o c a l a n d R em o t e M o n i t o r i n g
[S U B NE T M A S K]
[E NA B L E G A T E W A Y ]
M O D I F I E D ]
IP 1 9 2 . 1 6 8 . 0 . 2
IP
SE T T ING M O DIF IE D
IP : 2 1 0 . 1 7 . 1 3 9 . 1 4 5
Tele Eye RX U s er G u i d e
P O R T 1 0 2 4
SU B NE T M ASK 2 5 5 . 2 5 5 . 2 5 5 . 0
E NAB L E G AT E W AY NO
G AT E W AY 0 . 0 . 0 . 0
E NAB L E DNS NO
f ield can assign a number f rom 0 to 2 5 5
P R IM AR Y DNS 0 . 0 . 0 . 0
SE CO NDAR Y DNS 0 . 0 . 0 . 0
SU R E L INK …
11.a.7 Use “L ef t” or “Rig h t” button to
select f ield and use “U p ” or “D ow n ”
button to set number.
11.a.8 Press “E n ter ” button to save the change and
return previous menu.
P a g e 23
11.a.9 Follow the netw ork setting and assign a valid
subnet mask to
IP 2 1 0 . 1 7 . 1 3 9 . 1 4 5
P O R T 1 0 2 4
SU B NE T M ASK 2 5 5 . 2 5 5 . 2 5 5 . 0
[G A T E W A Y ] option in similar w ay .
E NAB L E G AT E W AY Y E S
G AT E W AY 2 1 0 . 1 7 . 1 3 9 . 1
E NAB L E DNS NO
P R IM AR Y DNS 0 . 0 . 0 . 0
N ote: The DN S setting is optional w hich is
SE CO NDAR Y DNS 0 . 0 . 0 . 0
SU R E L INK …
usef ul f or sureL I N K , time sy nchroniz ation and
SE T T ING W IL L T AKE E F F E CT
P R E SS E NT E R T O CO NT INU E
e-mail notif ication.
AF T E R R E ST AR T ,
O K
T CP / IP
and select
option and input
11.a.10 Press “L iv e” button, then [S E T T I NG
message board w ill pop up. Press
“E n ter ” button to restart the TeleEye R X .
B a s i c I n s t a l l a t i o n f o r L o c a l a n d R em o t e M o n i t o r i n g
Tele Eye RX U s er G u i d e
192.168.0.2
192.168.0.3
C r o s s
-
o v e r E t h e r n e t C a b l e
L oca l A r ea C on n ection s
11.b Conf igure TeleEye R X transmitter I P setting through PC
P a g e 24
P o w er A d ap t er
TeleEye R X
E t h er n et
S o ck et
RG59 cable
11.b.1. I n W indow s 2000/ X P desktop, select S ta r t >
C on tr ol P a n el
11.b.2. Double click Netw or k a n d D ia l - u p C on n ection s
> right click
and choose
P r op er ties .
11.b.3. Choose I n ter n et P r otocol ( T C P / I P ) and click
P r op er ties
C am er as
11.b.4. Enter an I P a ddr es s , s u b n et m a s k and D ef a u l t
g a tew a y . N o t e t h a t IP a d d r e s s s h o u l d b e
“ 1 9 2 . 1 6 8 . 0 . x x ” e x c e p t “ 1 9 2 . 1 6 8 . 0 . 2 ” w h i c h i s
TeleEye R X d e f a u l t IP a d d r e s s .
11.b.5. Enter the P r ef er r ed and A l ter n a te D NS s er v er ,
if necessary .
11.b.6. Click O K to activate the new I P.
Y ou have to conf irm that I P address has been
correctly set on y our computer. O n y our w indow s,
click s ta r t > r u n , ty pe “cm d” at open f ield, press
O K button, ty pe “ip con f ig ” on the DO S prompt
and y ou w ill see an I P set on y our computer.
B a s i c I n s t a l l a t i o n f o r L o c a l a n d R em o t e M o n i t o r i n g
Tele Eye RX U s er G u i d e
W in dow ]
P a g e 25
11.b.7. Connect the PC Ethernet socket to the transmitter
Ethernet socket at rear panel of the transmitter
w ith cr os s - ov er Ethernet cable. Check if the
{ L I NK L E D } of the transmitter is O N.
11.b.8. Run W X -30 sof tw are w hich has been installed to
the PC. (For details of W X -30 sof tw are
installation, please ref er to W X -30 Sof tw are
G uide)
11.b.9. Choose [T r a n s m itter ] [Reg is tr a tion ] to
register the TeleEye R X transmitter. User needs
to input transmitter serial number and registration
code.
For example :
S er ia l No. : VTC12345
Reg is tr a tion C ode : 1234567890
10/100 B A S E - T
L I N K C O L
11.b.10. Press [C on n ect] icon to pop up the [C on n ect
. Ty pe and select the f ollow ing setting :
P h on e/ I P : 192.168.0.2
C on n ect U s in g : TCP/ I P LA N
P a s s w or d: 000000
I P (192.168.0.2) and P a s s w or d (000000) are
def ault setting of TeleEye R X
B a s i c I n s t a l l a t i o n f o r L o c a l a n d R em o t e M o n i t o r i n g
Tele Eye RX U s er G u i d e
P a g e 26
11.b.11. Press [C on n ect]
icon to connect y our
PC to the transmitter. Live video is show n on the
W X -30 if success. O therw ise, the [W a r n in g ]
board w ill pop up and show y ou f ailure message.
For f ailure case, please press [C on n ect] icon
to check that the connection setting is valid or not.
11.b.12. Press [T r a n s m itter S etu p ] icon to show
TeleEye R X conf iguration menu.
11.b.13. Select [C on n ection ] and press [Netw or k
S ettin g s ] icon to conf igure
netw ork setting.
11.b.14. Change the I P f rom 192.168.0.2 to
210.17.139.145 (f or example). G atew ay setting is
used f or W A N . Primary and Secondary DN S
setting are used f or sureL I N K , time
sy nchroniz ation * * or e-mail notif ication f unction
* * .
11.b.15. Press [A p p l y ] icon to save the netw ork
setting and pop up the message board. A f ter
several seconds, the transmitter w ill restart
automatically .
B a s i c I n s t a l l a t i o n f o r L o c a l a n d R em o t e M o n i t o r i n g
Tele Eye RX U s er G u i d e
L oca l A r ea C on n ection s
Tele
Eye
R X
RG 5 9 cable
N et w o r k s w i t ch
21 0 .1 7 .1 39 . 14 6
21 0 .1 7. 1 39 . 14 7
11.b.16. I n W indow s 2000/ X P desktop, select S ta r t >
C on tr ol P a n el
11.b.17. Double click Netw or k a n d D ia l - u p C on n ection s
> right click
P r op er ties .
11.b.18. Choose I n ter n et P r otocol (TCP/ I P) and click
P r op er ties
11.b.19. Enter the I P a ddr es s , s u b n et m a s k and D ef a u l t
g a tew a y f or the PC to r es tor e to its or ig in a l
n etw or k con f ig u r a tion .
Note: The first 3 field of IP address should be
same as
tran smitter IP an d g atew ay
address. IP address is “2 1 0 .1 7 .1 39 .1 4 6 ” an d
g atew ay address is “2 1 0 .1 7 .1 39 .1 ” in this
ex amp le.
and choose
P a g e 27
11.b.20. Click O K to apply the settings
12. Disconnect the TeleEye R X transmitter and current PC. Reconnect the transmitter and
current PC to the LA N netw ork through s tr a ig h t- th r ou g h E th er n et ca b l e.
13. Check Ethernet socket of both TeleEye R X transmitter and PC to ensure that the
{ G RE E N L I NK L E D } turns O N . Then connection diagram is show n as below :
C C T V
M o n i t o r
P o w er A d ap t er
E t h er n et
S o ck et
S t r a i g h t -t h r o u g h E t h er n et c abl e
Tel e E y e R X
21 0. 1 7. 1 39 . 14 5
RG 5 9 cable
C am e r as
10/100 B A S E - T
L I N K C O L
B a s i c I n s t a l l a t i o n f o r L o c a l a n d R em o t e M o n i t o r i n g
Tele Eye RX U s er G u i d e
W X - 3 0
W in dow ]
[
W a r n in g
]
P a g e 28
14. Run
sof tw are at any local netw ork PC. (For
details of W X -30 sof tw are installation, please ref er
to W X -30 Sof tw are G uide)
15. Press [C on n ect] icon to pop up the [C on n ect
. For example, ty pe and select the
f ollow ing setting :
P h on e/ I P : 210.17.139.145
C on n ect U s in g : TCP/ I P LA N
P a s s w or d: 000000
16. Press [C on n ect] icon to connect y our PC
and the transmitter. The video appears on the W X 30 if success. O therw ise, the
board w ill
pop up and show y ou f ailure message. For f ailure
case, please press [C on n ect]
icon to check that
the connection setting is valid or not.
B a s i c I n s t a l l a t i o n f o r L o c a l a n d R em o t e M o n i t o r i n g
Tele Eye RX U s er G u i d e
R G 5 9 c a b l e
C. S e t u p TeleE y e R X f o r B r o a d b a n d o r N a r r o w b a n d
I n t e r n e t Co n n e c t i o n w i t h S t a t i c I P
C o n n ec t i o n T o p o l o g y
V I D EO O UT : C on ne c t to
m on i to r w i th R G 5 9 c a b l e a n d
B N C c o n ne c tor
V I D EO IN : C on ne ct t o
c a m e r a s w i th R G 5 9 c a b l e
a n d B N C c o n ne c t o r
P a g e 29
Te le E ye R X
R G 5 9 c a b l e
C a m e r a s
In te r n et
C C TV
M o ni to r
P o w e r A d a p te r
R o u t e r / G a t e w a y
R o u t e r / G a t e w a y
E th e r n et
S o c k e t
S tr a i g h t-th r o u g h E t h er n et c a b l e
S tr a i g h t-th r o u g h E t h er n et c a b l e
* * F or R X 36 8 / R X 36 1 6 , the “VIDEO OUT” p ort is on the rig ht side of “VIDEO IN ” * *
R em a r k f o r I n t er n et C o n n ec t i o n D ef i n i t i o n
B r oa db a n d : Connection speed is 128kbps or above, e.g. A DSL, DSL.
Na r r ow b a n d : Connection speed is below 128kbps, e.g. dial up netw ork, G PRS
Eq u i p m en t
TeleEye R X Transmitter
N etw ork Sw itch, Router/ G atew ay
Straight-through Ethernet Cable (bundled)
Cross-over Ethernet Cable
Cameras, Video Cables (RG -59) w ith BN C H eader
CCTV M onitor
CD RO M w ith W X -30 Sof tw are (bundled) (f or PC operation only )
PC
P C R eq u i r em en t s
C P U : Pentium I V 2.4 G H z or above
RA M : 512 M B or above
D is p l a y : 1024x768, true color or better
O S : M S W indow s 2000, X P
H D D : 1 G B of f ree disk space or above
B a s i c I n s t a l l a t i o n f o r L o c a l a n d R em o t e M o n i t o r i n g
Tele Eye RX U s er G u i d e
P a g e 30
S et u p P r o c ed u r e
1. Connect cameras to TeleEye R X { Video I nput} w ith RG 59 cable and BN C connector.
Note: The c amera sy stem is either N TS C or P A L an d sup p oses all c ameras use the S A M E
sy stem format.
2. Connect CCTV monitor to TeleEye R X { Video O utput} w ith RG 59 cable and BN C
connector.
3. I nstall and use the bundled key to lock the { H ard Disk Rack} w ith hard disk to the TeleEye
R X .
Note: If there is n o hard disk in stalled, R ec ordin g an d Play bac k are n ot fun c tion al.
4. Connect the pow er adapter (12V DC) to the TeleEye R X .
5. Turn on the pow er of TeleEye R X , camera and monitor. Check the { P ow er L E D }
w hich is lit up in blue color continuously at TeleEye R X f ront panel af ter pow er on. A f ter
several seconds, live video appears on the CCTV monitor as f ollow s:
,
Note: Please g o throug h the follow in g step s ( 6 - 1 0 ) if the v ideo of C C TV mon itor does n ot show
B a s i c I n s t a l l a t i o n f o r L o c a l a n d R em o t e M o n i t o r i n g
c learly .
Tele Eye RX U s er G u i d e
192.168.0.2
RG59 ca b l e
MAIN MENU
V ID EO
S ET UP MENU
R ES T O R E F AC T O R Y S ET T ING
ENT ER
P a g e 31
6. Press the “M en u ”
button to pop up the [M A I N
M E NU ] on O SD.
7. Use “U p ” or “D ow n ” button to select
[S E T U P ] option and press “E n ter ” button to
enter the [S E T U P ] sub-menu.
8. Select [V I D E O ] option and press “E n ter ”
button
to enter the [V I D E O ] sub-menu.
9. Select [V I D E O F O RM A T ] and press “L ef t”
S ET UP . . .
B AC K UP T O C D - R . . .
S W IT C H C O NT R O L . . .
S C AN / F O R MAT D IS K . . .
T R ANS MIT T ER INF O . . .
L O C K K EY S ENT ER
D IAG NO S T IC . . .
S H UT D O W N ENT ER
V ID EO . . .
R EC O R D ING . . .
S W IT C H ES . . .
D AT E / T IME . . .
C O NNEC T IO N . . .
EV ENT H AND L ER . . .
P AS S W O R D . . .
T R ANS MIT T ER . . .
or “Rig h t” button to set either [NT S C ] or
[P A L ] option. (A ll cameras should have the same
video f ormat).
C AMER A S ET T ING . . .
L O C AL MO NIT O R ING . . .
O S D C O L O R B L UE
V ID EO F O R MAT P AL
10. Y ou can alw ay s press “L iv e” button to exit any
menu operation and start live monitoring.
Setup TeleEye R X transmitter I P through CCTV monitor, please go to step 11a.
Setup TeleEye R X transmitter I P through PC, please go to step11b.
11.a Conf igure TeleEye R X transmitter I P setting through CCTV M onitor
TeleEye R X
E t h e r n e t
S o ck e t
P o w e r A d a p t e r
RG59 ca b l e
C a m e r a s
C C T V
M o n i t o r
B a s i c I n s t a l l a t i o n f o r L o c a l a n d R em o t e M o n i t o r i n g
Tele Eye RX U s er G u i d e
S ET UP MENU
R ES T O R E F AC T O R Y S ET T ING
ENT ER
C O NNEC T IO N
IP
S ET T ING MO D IF IED
P a g e 32
11.a.1 Press the “M en u ”
button such that the O S D
m a in m en u pops up on the monitor.
11.a.2 Use “U p ” or “D ow n ” button to select
[S E T U P ] option and press “E n ter ” button.
11.a.3 Select [C O NNE C T I O N] option and press
“E n ter ” button
11.a.4 Select [T C P / I P ] option and Press “E n ter ”
button
11.a.5 Select [I P ] option and press “E n ter ” button. I P
address consists of f ou r f iel ds . Each f ield can
assign a number f rom 0 to 2 5 5 .
V ID EO . . .
R EC O R D ING . . .
S W IT C H ES . . .
D AT E / T IME . . .
C O NNEC T IO N . . .
EV ENT H AND L ER . . .
P AS S W O R D . . .
T R ANS MIT T ER . . .
T C P / IP …
MO D EM …
T H R O UG H P UT …
T C P / IP
IP 1 9 2 . 1 6 8 . 0 . 2
P O R T 1 0 2 4
S UB NET MAS K 2 5 5 . 2 5 5 . 2 5 5 . 0
ENAB L E G AT EW AY NO
G AT EW AY 0 . 0 . 0 . 0
ENAB L E D NS NO
P R IMAR Y D NS 0 . 0 . 0 . 0
S EC O ND AR Y D NS 0 . 0 . 0 . 0
S UR EL INK …
11.a.6 Use “L ef t”
or “Rig h t” button to select f ield and use
“D ow n ” button to set number.
11.a.7 Press “E n ter ” button to save the change and return
previous menu.
11.a.8 Follow the netw ork setting and assign valid subnet
mask to [S U B NE T M A S K] and select [E NA B L E
G A T E W A Y ] option and input [G A T E W A Y ]
option in similar w ay .
11.a.9 Set the G atew ay value (f or example) to
2 10 .17 .13 9.1
Note: The D NS settin g is op tion al w hic h is useful
for sureL I N K , time sy n c hron iz ation * * or e- mail
n otific ation fun c tion * * .
11.a.10 Press “L iv e”
button and [S E T T I NG
M O D I F I E D ] message board w ill pop up.
“U p ” or
IP : 2 1 0 . 1 7 . 1 3 9 . 1 4 5
T C P / IP
IP 2 1 0 . 1 7 . 1 3 9 . 1 4 5
P O R T 1 0 2 4
S UB NET MAS K 2 5 5 . 2 5 5 . 2 5 5 . 0
ENAB L E G AT EW AY Y ES
G AT EW AY 2 1 0 . 1 7 . 1 3 9 . 1
ENAB L E D NS NO
P R IMAR Y D NS 0 . 0 . 0 . 0
S EC O ND AR Y D NS 0 . 0 . 0 . 0
S UR EL INK …
S ET T ING W IL L T AK E EF F EC T
AF T ER R ES T AR T ,
P R ES S ENT ER T O C O NT INUE
O K
11.b Conf igure TeleEye R X transmitter I P setting through PC
B a s i c I n s t a l l a t i o n f o r L o c a l a n d R em o t e M o n i t o r i n g
Tele Eye RX U s er G u i d e
192.168.0.2
192.168.0.3
C r o s s
-
o v e r E t h e r n e t C a b l e
S ta r t
Netw or k a n d D ia l - u p
C on n ection s
L oca l A r ea
I n ter n et P r otocol ( T C P / I P )
Enter the Pref erred and A lternate DN S server, if
P o w er A d ap t er
E t h er n et
S o ck et
P a g e 33
TeleEye R X
RG59 cable
C am er as
11.b.1. I n W indow s 2000/ X P desktop, select
>
C on tr ol P a n el
11.b.2. Double click
> right click
C on n ection s and choose P r op er ties .
11.b.3. Choose
and click
P r op er ties
11.b.4. Enter an I P address, subnet mask and Def ault
gatew ay . N ote that I P address should be
“192.168.0.xx” except “192.168.0.2” w hich is
TeleEye R X def ault I P address.
11.b.5.
necessary .
11.b.6. Click O K to activate the new I P.
Note: Y ou hav e to c on firm that IP address has
been c orrec tly set on y our c omp uter. O n y our
w in dow s, c lic k s t a r t > r u n , ty p e “c md” at O p en
field an d p ress OK button , then ty p e “i p c o n f i g ”
on the D O S p romp t, y ou w ill see an IP set on
y our c omp uter.
B a s i c I n s t a l l a t i o n f o r L o c a l a n d R em o t e M o n i t o r i n g
Tele Eye RX U s er G u i d e
cr os s - ov er
{ L I NK L E D }
[T r a n s m itter ]
[Reg is tr a tion ]
Tele
Eye
R X
[C on n ect W in dow ]
C on n ect U s in g
P a g e 34
11.b.7. Connect the PC Ethernet socket to the
transmitter Ethernet socket at rear panel of the
transmitter w ith
Check if the
Ethernet cable.
of the transmitter is
O N.
11.b.8. Run W X -30 sof tw are w hich has been installed to
the PC. (For details of W X -30 sof tw are
installation, please ref er to W X -30 Sof tw are
G uide)
11.b.9. Choose
register the
transmitter. User needs
to
to input transmitter serial number and
registration code.
For example :
S er ia l No. : VTC12345
Reg is tr a tion C ode : 1234567890
10/100 B A S E - T
L I N K C O L
11.b.10. Press [C on n ect] icon to pop up the
f ollow ing setting :
F or B r oa db a n d C on n ection :
P h on e/ I P : 192.168.0.2
C on n ect U s in g : TCP/ I P Broadband
P a s s w or d : 000000
O R
F or Na r r ow b a n d C on n ection :
P h on e/ I P : 192.168.0.2
P a s s w or d : 000000
I P (192.168.0.2) and P a s s w or d (000000)
B a s i c I n s t a l l a t i o n f o r L o c a l a n d R em o t e M o n i t o r i n g
. Ty pe and select the
: TCP/ I P N arrow band
Tele Eye RX U s er G u i d e
[
W a r n in g
]
[C on n ection ]
[Netw or k
sure
L I N K
P a g e 35
11.b.11. Press [C on n ect]
icon to connect
y our PC and the transmitter. The video appears
on the W X -30 if success. O therw ise, the
board w ill pop up and show y ou
f ailure message. For f ailure case, please press
[C on n ect] icon to check that the connection
setting is valid or not.
11.b.12. Press [T r a n s m itter s etu p ] icon to show
TeleEye R X conf iguration menu.
11.b.13. Select
and press
S ettin g s ] icon to conf igure
netw ork setting.
11.b.14. Change the I P f rom 192.168.0.2 to (f or example)
210.17.139.145 and G atew ay setting
210.17.139.1 (f or example). Primary and
Secondary DN S setting (f or example) are used
f or
, time sy nchroniz ation* * or e-mail
notif ication f unction * * .
11.b.15. Press [A p p l y ] icon to save the
netw ork setting and pop up the message board.
A f ter several seconds, the transmitter w ill restart
automatically .
B a s i c I n s t a l l a t i o n f o r L o c a l a n d R em o t e M o n i t o r i n g
Tele Eye RX U s er G u i d e
S ta r t
Netw or k a n d D ia l - u p
C on n ection s
L oca l A r ea
I n ter n et P r otocol ( T C P / I P )
RG59 cable
P a g e 36
11.b.16. I n W indow s 2000/ X P desktop, select
>
C on tr ol P a n el
11.b.17. Double click
> right click
C on n ection s and choose P r op er ties .
11.b.18. Choose
and click
P r op er ties
11.b.19. Enter the I P address, subnet mask and Def ault
gatew ay f or the PC to restore to its original
netw ork conf iguration.
11.b.20. Click O K to apply the setting
12. Disconnect the transmitter and current PC. Reconnect the transmitter and current PC to the
I nternet netw ork through s tr a ig h t- th r ou g h E th er n et ca b l e.
13. Check Ethernet socket of both the transmitter and PC to ensure that the { G RE E N L I NK
L E D } turns O N . Then connection diagram is show n as f ollow s:
10/100 B A S E - T
L I N K C O L
I n t er n et
C C T V
M o n i t o r
P o w er A d ap t er
R o u t e r / G a t e w a y
2 1 0 . 1 7 . 1 3 9 . 1
2 1 1 . 1 3 4 . 1 3 9 . 1
R o u t e r / G a t e w a y
E t h er n et
S o ck et
S t r ai g h t -t h r o u g h E t h er n et cable
RG59 cable
S t r ai g h t -t h r o u g h E t h er n et cable
TeleEye R X
2 1 0 . 1 7 . 1 3 9 . 1 4 5
C am er as
2 1 1 . 1 3 4 . 1 3 9 . 9
2 1 1 . 1 3 4 . 1 3 9 . 7
B a s i c I n s t a l l a t i o n f o r L o c a l a n d R em o t e M o n i t o r i n g
Tele Eye RX U s er G u i d e
Tele
Eye R X
W X - 3 0
[C on n ect W in dow ]
ex a m p l e
[
W a r n in g
]
14. Conf igure the netw ork setting f or
transmitter and y our PC if necessary , such as
router/ gatew ay port mapping (select
router/ gatew ay I P as I P provided by y our I SP
and the transmitter I P as I P provided by the
router/ gatew ay ), f irew all, etc. (Please ref er to the
manual of y our router/ gatew ay .)
P a g e 37
15. Run
sof tw are at any netw ork PC. (For
details of W X -30 sof tw are installation, please
ref er to W X -30 Sof tw are G uide)
16. Press [C on n ect] icon to pop up the
. For
, ty pe and
select the f ollow ing setting :
B r oa db a n d C on n ection :
P h on e/ I P : 210.17.139.145
C on n ect U s in g : TCP/ I P Broadband
P a s s w or d : 000000
O R
Na r r ow b a n d C on n ection :
P h on e/ I P : 210.17.139.145
C on n ect U s in g : TCP/ I P N arrow band
P a s s w or d : 000000
17. Press [C on n ect] icon to connect y our
PC and the transmitter. The video appears on the
W X -30 if success. O therw ise, the
board w ill pop up and show y ou f ailure message.
For f ailure case, please press [C on n ect] icon
to check that the connection setting is valid or
not.
B a s i c I n s t a l l a t i o n f o r L o c a l a n d R em o t e M o n i t o r i n g
Tele Eye RX U s er G u i d e
R G 5 9 c a b le
E th er n e t
D. S e t u p TeleE y e R X f o r B r o a d b a n d o r N a r r o w b a n d
I n t e r n e t C o n n e c t i o n w i t h Dy n a m i c I P
C o n n ec t i o n T o p o l o g y
V ID E O O U T : C o n n e c t t o
m on i tor w i th R G 5 9 c a b l e
a n d B N C co n n e c tor
V ID E O IN : C onnect to
ca m er a s w i th R G 5 9 ca b l e
a n d B N C co n nec t o r
P a g e 38
Te l e E y e R X
w w w . y o u r_site .y o u r _ c o mp a n y.te le e y e . n e t
C a m e r a s
I n te rn e t
C C T V
M o ni to r
P o w er A d a p te r
R o u t e r / G a t e w a y
R o u t e r / G a t e w a y
S o c k e t
S tr a i g h t-t h r o u g h E t h er n et c a b l e
R G 5 9 c a b le
S tr a i g h t-th r ou g h E t h er n e t c a b l e
* * F or R X 36 8 / R X 36 1 6 , the “VIDEO OUT” p ort is on the rig ht side of “VIDEO IN ” * *
R em a r k f o r I n t er n et C o n n ec t i o n D ef i n i t i o n
Broadband : Connection speed is eq ual or above 128kbps, e.g. A DSL, DSL.
N arrow band : Connection speed is below 128kbps, e.g. dial up netw ork, G PRS
Eq u i p m en t
TeleEye R X Transmitter
N etw ork Sw itch, Router/ G atew ay , A DSL M odem
Straight-through Ethernet Cable (bundled), Cross-over Ethernet Cable
Cameras, Video Cables (RG -59) w ith BN C H eader, M onitor
CD RO M w ith W X -30 Sof tw are (bundled) (f or PC operation only )
CCTV M onitor
PC
P C R eq u i r em en t s
C P U : Pentium I V 2.4 G H z or above
RA M : 512 M B or above
D is p l a y : 1024 x 768, true color or better
H D D : 1 G B of f ree disk space or above
O S : M S W indow s 2000, X P
B a s i c I n s t a l l a t i o n f o r L o c a l a n d R em o t e M o n i t o r i n g
Tele Eye RX U s er G u i d e
S et u p P r o c ed u r e
P a g e 39
1. Connect cameras to TeleEye R X { Video I nput} w ith RG 59 cable and BN C connector.
Note: The c amera sy stem is either N TS C or P A L an d sup p ose all c ameras use the S A M E
sy stem format.
2. Connect CCTV monitor to TeleEye R X { Video O utput} w ith RG 59 cable and BN C
connector.
3. I nstall and use the bundled key to lock the { H ard Disk Rack} w ith H ard disk to the
TeleEye R X .
Note: If there is n o hard disk in stalled, R ec ordin g an d Play bac k are n ot fun c tion al.
4. Connect the pow er adapter (12V DC) to the TeleEye R X .
5. Turn on the pow er of TeleEye R X , camera and monitor. Check the { P ow er L E D }
w hich is lit up in blue color continuously at TeleEye R X f ront panel af ter pow er on. A f ter
several seconds, live video appears on the CCTV monitor as f ollow s:
,
Note: Please g o throug h the follow in g step s ( 6 - 1 0 ) if the v ideo of C C TV mon itor does n ot show
B a s i c I n s t a l l a t i o n f o r L o c a l a n d R em o t e M o n i t o r i n g
c learly .
Tele Eye RX U s er G u i d e
192.168.0.2
RG59 ca b l e
SETUP MENU
R ESTO R E F A C TO R Y SETTI NG
ENTER
V I DEO
SETUP MENU
R ESTO R E F A C TO R Y SETTI NG
ENTER
P a g e 40
6. Press the “M en u ”
M E NU ] on O SD.
7. Use “U p ” or “D ow n ” button to select
[S E T U P ] option and press “E n ter ” button to
enter the [S E T U P ] sub-menu.
button to pop up the [M A I N
V I DEO . . .
R EC O R DI NG . . .
SW I TC H ES . . .
DA TE / TI ME . . .
C O NNEC TI O N . . .
EV ENT H A NDL ER . . .
PA SSW O R D . . .
TR A NSMI TTER . . .
8. Select [V I D E O ] option and press “E n ter ”
button
9. Select [V I D E O F O RM A T ] and press “L ef t”
or “Rig h t” button to set either [NT S C ] or
[P A L ] option. (A ll cameras should have the same
video f ormat).
C A MER A SETTI NG . . .
L O C A L MO NI TO R I NG . . .
O SD C O L O R B L UE
V I DEO F O R MA T PA L
10. Y ou can alw ay s press “L iv e” button to exit any
menu operation and start live monitoring.
Setup TeleEye R X transmitter I P through CCTV monitor, please go to step 11a.
Setup TeleEye R X transmitter I P through PC, please go to step11b.
11.a Conf igure TeleEye R X transmitter I P setting through CCTV M onitor
P o w e r A d a p t e r
TeleEye R X
E t h e r n e t S o ck e t
RG59 ca b l e
C a m e r a s
11.a.1 Press the “M en u ” button such that the O SD
main menu pops up on the monitor.
V I DEO . . .
R EC O R DI NG . . .
11.a.2 Use “U p ” or “D ow n ” button to select
[S E T U P ] option and press “E n ter ” button.
SW I TC H ES . . .
DA TE / TI ME . . .
C O NNEC TI O N . . .
EV ENT H A NDL ER . . .
PA SSW O R D . . .
TR A NSMI TTER . . .
11.a.3 Select [C O NNE C T I O N]option and press
C C T V
M o n i t o r
“E n ter ” button
B a s i c I n s t a l l a t i o n f o r L o c a l a n d R em o t e M o n i t o r i n g
Tele Eye RX U s er G u i d e
C O NNEC TI O N
TH R O UG H PUT
…
TC P / I P
SUR EL I NK
…
IP
TC P / I P
SUR EL I NK
P a g e 41
11.a.4 Select [T C P / I P ] option and Press “E n ter ”
button
TC P / I P …
MO DEM …
11.a.5 Select [I P ] option and press “E n ter ” button.
I P 1 9 2 .1 6 8 .0 .2
I P address consists of f our f ields. Each f ield can
assign a number f rom 0 to 2 5 5 .
PO R T 1 0 2 4
SUB NET MA SK 2 5 5 .2 5 5 .2 5 5 .0
ENA B L E G A TEW A Y NO
G A TEW A Y 0 .0 .0 .0
ENA B L E DNS NO
PR I MA R Y DNS 0 .0 .0 .0
SEC O NDA R Y DNS 0 .0 .0 .0
11.a.6 Use “L ef t”
f ield and use “U p ” or “D ow n ” button to
or “Rig h t” button to select
IP : 2 1 0 . 1 7 . 1 3 9 . 5
set number. Set I P address (f or example) to
210.17.139.5
11.a.7 Press “E n ter ” button to save the change and return previous menu.
I P 2 1 0 .1 7 .1 3 9 .5
PO R T 1 0 2 4
11.a.8 Follow the netw ork setting and assign valid subnet
mask to [S U B NE T M A S K] and select [E NA B L E
G A T E W A Y ] option and input [G A T E W A Y ]
option in similar w ay . A ssign the G atew ay (f or
example) to 210.17.139.1
11.a.9 Select [E NA B L E D NS ] option Use “L ef t”
or
SUB NET MA SK 2 5 5 .2 5 5 .2 5 5 .0
ENA B L E G A TEW A Y Y ES
G A TEW A Y 2 1 0 .1 7 .1 3 9 .1
ENA B L E DNS NO
PR I MA R Y DNS 0 .0 .0 .0
SEC O NDA R Y DNS 0 .0 .0 .0
SUR EL I NK …
“Rig h t” button to select [Y E S ] to enable DN S.
11.a.10 A ssign the Primary DN S (f or example) to 202.14.67.4
11.a.11 A ssign the Secondary DN S (f or example) to 202.14.67.14
11.a.12 Select [S U RE L I NK] option f rom TCP/ I P menu and press “E n ter ” button to enter
the sub menu.
ENA B L ED Y ES
SUR EL I NK A DDR ESS www…..
R EF R ESH R A TE 1 MI NS
11.a.13 Select [E NA B L E D ] option and press “L ef t” or “Rig h t” button to set [Y E S ]
value
11.a.14 Select [S U RE L I NK A D D RE S S ] option and press “E n ter ”
sureL I N K editing menu.
B a s i c I n s t a l l a t i o n f o r L o c a l a n d R em o t e M o n i t o r i n g
button to
Tele Eye RX U s er G u i d e
192.168.0.2
192.168.0.3
C r o s s
-
o v e r E t h e r n e t C a b l e
SUR EL I NK A DDR ESS
SETTI NG MO DI F I ED
There are tw o f ields f or assigning sureL I N K
address
“w w w .y ou r _ s ite.y ou r _ com p a n y .teleEye.net”
0 1 2 3 4 5 6 7 8 9
P a g e 42
A B C D E F G H I J
K L M N O P Q R S T
U V W X Y Z B A C K NEX T
C L EA R END
W W W . _ . TEL EEY E.NET
11.a.15 Use “U p ” or “D ow n ” or “L ef t” or “Rig h t”
button to select values and use “E n ter ” button
to assign value.
11.a.16 [B A C K] back to previous value or f ield
11.a.17 [NE X T ] next to f ield
11.a.18 [C L E A R] clear f ield
11.a.19 [E ND ] f inish to assign sureL I N K address and exit the editing menu.
11.a.20 Press “L iv e”
button and [S E T T I NG M O D I F I E D ] message board w ill pop up. Press
“E n ter ” button to restart the transmitter.
SETTI NG W I L L TA K E EF F EC T
A F TER R ESTA R T ,
PR ESS ENTER TO C O NTI NUE
11b: Conf igure TeleEye R X transmitter I P setting
O K
through PC
TeleEye R X
P o w e r A d a p t e r
RG59 ca b l e
E t h e r n e t S o ck e t
C a m e r a s
B a s i c I n s t a l l a t i o n f o r L o c a l a n d R em o t e M o n i t o r i n g
Tele Eye RX U s er G u i d e
11.b.1. I n W indow s 2000/ X P desktop, select S ta r t >
C on tr ol P a n el
11.b.2. Double click Netw or k a n d D ia l - u p
C on n ection s > right click L oca l A r ea
C on n ection s and choose P r op er ties .
11.b.3. Choose I n ter n et P r otocol ( T C P / I P ) and click
P r op er ties
P a g e 43
11.b.4. Enter an I P address, subnet mask and Def ault
gatew ay .
Note: IP address should be “1 9 2 .1 6 8 .0 .x x ”
ex c ep t “1 9 2 .1 6 8 .0 .2 ” w hic h is TeleEye R X
default IP address.
11.b.5. Enter the Pref erred and A lternate DN S server, if
necessary .
11.b.6. Click O K to activate the new I P.
Y ou have to conf irm that I P address has been
correctly set on y our computer. O n y our
w indow s, click s ta r t > r u n , ty pe “cm d” at
O pen f ield and press O K button, then ty pe
“ip con f ig ” on the DO S prompt, y ou w ill see an
I P set on y our computer.
11.b.7. Connect the PC Ethernet socket to the
transmitter Ethernet socket at rear panel of the
transmitter w ith cr os s - ov er Ethernet cable.
Check if the { L I NK L E D } of the transmitter is
O N.
10/100 B A S E - T
L I N K C O L
B a s i c I n s t a l l a t i o n f o r L o c a l a n d R em o t e M o n i t o r i n g
Tele Eye RX U s er G u i d e
11.b.8. Run W X -30 sof tw are w hich has been installed
to the PC. (For details of W X -30 sof tw are
installation, please ref er to W X -30 Sof tw are
G uide)
11.b.9. Choose [T r a n s m itter ] [Reg is tr a tion ] to
register the TeleEye R X transmitter. User
needs to input transmitter serial number and
registration code.
For example :
S er ia l No. : VTC12345
Reg is tr a tion C ode : 1234567890
P a g e 44
11.b.10. Press [C on n ect] icon to pop up the
[C on n ect W in dow ]. Ty pe and select the
f ollow ing setting :
B r oa db a n d C on n ection :
P h on e/ I P : 192.168.0.2
C on n ect U s in g : TCP/ I P Broadband
P a s s w or d : 000000
O R
Na r r ow b a n d C on n ection :
P h on e/ I P : 192.168.0.2
C on n ect U s in g : TCP/ I P N arrow band
P a s s w or d : 000000
I P (192.168.0.2) and P a s s w or d (000000) are
def ault setting of TeleEye R X
B a s i c I n s t a l l a t i o n f o r L o c a l a n d R em o t e M o n i t o r i n g
Tele Eye RX U s er G u i d e
w w w .y ou r _ s ite.y ou r _ com p a n y .T el eE y e.n et
P a g e 45
11.b.11. Press [C on n ect]
icon to connect y our
PC and the transmitter. The video appears on
the W X -30 if success. O therw ise, the
[W a r n in g ] board w ill pop up and show y ou
f ailure message. For f ailure case, please press
[C on n ect] icon to check that the
connection setting is valid or not.
11.b.12. Press [T r a n s m itter S etu p ] icon to show
TeleEye R X conf iguration menu.
11.b.13. Select [C on n ection ] and press [Netw or k
S ettin g s ] icon to conf igure
netw ork setting.
11.b.14. For example :
A ssign 210.17.139.5 to I P
A ssign 210.17.139.1 to G atew ay
A ssign 202.14.67.4 to Primary DN S
A ssign 202.14.67.14 to Secondary DN S
Enable sureL I N K
A ssign
“
Note: The abov e n etw ork settin g is an ex amp le.
Please c on sult y ou n etw ork admin istrator to g et
y our n etw ork settin g in formation
”
B a s i c I n s t a l l a t i o n f o r L o c a l a n d R em o t e M o n i t o r i n g
Tele Eye RX U s er G u i d e
RG59 cable
P a g e 46
11.b.15. Press [A p p l y ]
icon to save the
netw ork setting and pop up the message board.
A f ter several seconds, the transmitter w ill
restart automatically .
11.b.16. I n W indow s 2000/ X P desktop, select S ta r t >
C on tr ol P a n el
11.b.17. Double click Netw or k a n d D ia l - u p
C on n ection s > right click L oca l A r ea
C on n ection s and choose P r op er ties .
11.b.18. Choose I n ter n et P r otocol ( T C P / I P ) and click
P r op er ties
11.b.19. Enter the I P address, subnet mask and Def ault
gatew ay f or the PC to restore to its original
netw ork conf iguration.
11.b.20. Click O K to apply the setting
12. Disconnect the transmitter and current PC. Reconnect the transmitter and current PC to the
I nternet netw ork through s tr a ig h t- th r ou g h E th er n et ca b l e.
13. Check Ethernet socket of both the transmitter and PC to ensure that the { G RE E N L I NK
L E D } turns O N . Then connection diagram is show n as f ollow s:
P rimary D N S : 2 0 2 .1 4 .6 7 .4
I nternet
C C T V
M o n i to r
P o w er A d ap ter
R o u t e r / G a t e w a y
2 1 0 .1 7 .1 3 9 .1
E th er n et
S o ck et
S tr ai g h t-th r o u g h E th er n et cable
S tr ai g h t-th r o u g h E th er n et cable
2 1 1 .1 3 4 .1 3 9 .1
TeleEye R X
www.your_site.your_company.teleeye.net
RG59 cable
C am er as
2 1 1 .1 3 4 .1 3 9 .9
2 1 1 .1 3 4 .1 3 9 .7
S econd ary D N S : 2 0 2 .1 4 .6 7 .1 4
R o u t e r / G a t e w a y
B a s i c I n s t a l l a t i o n f o r L o c a l a n d R em o t e M o n i t o r i n g
Tele Eye RX U s er G u i d e
14. Conf igure the netw ork setting f or TeleEye R X
transmitter and y our PC if necessary , such as
router/ gatew ay port mapping (select router/ gatew ay
I P as I P provided by y our I SP and the transmitter I P
as I P provided by the router/ gatew ay ), f irew all, etc.
(Please ref ers to the manual of y our router/ gatew ay .)
15. Run W X - 3 0 sof tw are at any netw ork PC. (For
details of W X -30 sof tw are installation, please ref er
to W X -30 Sof tw are G uide)
16. Press [C on n ect] icon to pop up the [C on n ect
W in dow ]. For ex a m p l e, ty pe and select the
f ollow ing setting :
B r oa db a n d C on n ection :
P h on e/ I P :
w w w .y our_ site.y our_ company .TeleEy e.net
C on n ect U s in g : TCP/ I P Broadband
P a s s w or d : 000000
O R
Na r r ow b a n d C on n ection :
P h on e/ I P :
w w w .y our_ site.y our_ company .TeleE y e .net
C on n ect U s in g : TCP/ I P N arrow band
P a s s w or d : 000000
P a g e 47
17. Press [C on n ect] icon to connect y our
PC and the transmitter. The video appears on the
W X -30 if success. O therw ise, the [W a r n in g ] board
w ill pop up and show y ou f ailure message. For
f ailure case, please press [C on n ect] icon to
check that the connection setting is valid or not.
B a s i c I n s t a l l a t i o n f o r L o c a l a n d R em o t e M o n i t o r i n g
Tele Eye RX U s er G u i d e
R G 5 9
ca b l e
E. S e t u p TeleEy e R X f o r M o d e m C o n n e c t i o n
C o n n ec t i o n T o p o l o g y
VIDEO OUT: Connect to
M od em p or t connect
to a DB -9 connector
m oni tor w i th R G 5 9 ca b l e
a nd B N C connector
VIDEO IN : Connect to
ca m er a s w i th R G 5 9 ca b l e
a nd B N C connector
P a g e 48
CCTV
M oni tor
P ow er A d a p ter
Tel ep h one ca b l e
Telephone
Net w or k
R S 2 3 2 s er i a l ca b l e
M od em
Tel ep h one ca b l e
R S 2 3 2 s er i a l ca b l e
M od em
TeleEye R X
R G 5 9 ca b l e
Ca m er a s
* * F or R X 36 8 / R X 36 1 6 , the “VIDEO OUT” p ort is on the rig ht side of “VIDEO IN ” * *
Eq u i p m en t
TeleEye R X Transmitter
I SDN / PSTN M odem
RS232 Serial Cable
Telephone Cable
Cameras
Video Cables (RG -59) w ith BN C H eader
CCTV M onitor
CD RO M w ith W X -30 Sof tw are (bundled) (f or PC operation only )
PC
P C R eq u i r em en t s
C P U : Pentium I V 2G H z or above
RA M : 256 M B or above
D is p l a y : 800x600, hi-color or better
O S : M S W indow s 2000, X P
B a s i c I n s t a l l a t i o n f o r L o c a l a n d R em o t e M o n i t o r i n g
Tele Eye RX U s er G u i d e
P a g e 49
S et u p P r o c ed u r e
1. Connect cameras to TeleEye R X { V ideo I n p u t} w ith RG 59 cable and BN C connector.
Note: The c amera sy stem is either N TS C or P A L an d all c ameras must be the same sy stem
format.
2. Connect CCTV monitor to TeleEye R X { V ideo O u tp u t} w ith RG 59 cable and BN C
connector.
3. I nstall and use the bundled key to lock the { H a r d D is k Ra ck } w ith hard disk to the
TeleEye R X .
Note: If there is n o hard disk in stalled, R ec ordin g or Play bac k is n ot fun c tion al durin g liv e
v ideo mon itorin g .
4. Connect the pow er adapter (12V DC) to the TeleEye R X .
5. Turn on the pow er of TeleEye R X , camera and monitor. Check the { P ow er L E D }
w hich is lit up in blue color continuously at TeleEye R X f ront panel af ter pow er on. A f ter
several seconds, live video appears on the CCTV monitor as f ollow s:
,
Note: Please g o throug h the follow in g step s ( 6 - 1 0 ) if the v ideo of C C TV mon itor does n ot show
B a s i c I n s t a l l a t i o n f o r L o c a l a n d R em o t e M o n i t o r i n g
c learly .
Tele Eye RX U s er G u i d e
192.168.0.2
RG59 ca b l e
[C O NNE C T I O N]
SETUP MENU
R ESTO R E F A C TO R Y SETTI NG
ENTER
V I D EO
SETUP MENU
R ESTO R E F A C TO R Y SETTI NG
ENTER
C O NNEC TI O N
P a g e 50
6. Press the “M en u ”
M E NU ] on O SD.
7. Use “U p ” or “D ow n ” button to select
[S E T U P ] option and press “E n ter ” button to
button to pop up the [M A I N
V I D EO . . .
R EC O R D I NG . . .
SW I TC H ES . . .
D A TE / TI ME . . .
C O NNEC TI O N . . .
EV ENT H A ND L ER . . .
PA SSW O R D . . .
TR A NSMI TTER . . .
enter the [S E T U P ] sub-menu.
8. Select [V I D E O ] option and press “E n ter ”
button
9. Select [V I D E O F O RM A T ] and press “L ef t”
or “Rig h t” button to set either [NT S C ] or
[P A L ] option. (A ll cameras should have the same
video f ormat).
C A MER A SETTI NG . . .
L O C A L MO NI TO R I NG . . .
O SD C O L O R B L UE
V I D EO F O R MA T PA L
10. Y ou can alw ay s press “L iv e” button to exit any
menu operation and start live monitoring.
Setup TeleEye R X transmitter I P through CCTV monitor, please go to step 11a.
Setup TeleEye R X transmitter I P through PC, please go to step11b.
11a: Conf igure TeleEye R X transmitter modem connection setting through CCTV M onitor
TeleEye R X
C C T V
M o n i t o r
P o w e r A d a p t e r
E t h e r n e t
S o ck e t
RG59 ca b l e
C a m e r a s
11.a.1. Press the “M en u ” button such that the O SD
[M A I N M E NU ] pop up on the monitor.
V I D EO . . .
11.a.2. Use “U p ” or “D ow n ” button to select
R EC O R D I NG . . .
SW I TC H ES . . .
D A TE / TI ME . . .
C O NNEC TI O N . . .
[S E T U P ] option and press “E n ter ” button
EV ENT H A ND L ER . . .
and select
PA SSW O R D . . .
TR A NSMI TTER . . .
option and press
“E n ter ” button.
11.a.3. Use “U p ” or “D ow n ” button to select
TC P / I P …
MO D EM …
[M O D E M ] option and press “E n ter ” button
TH R O UG H PUT …
B a s i c I n s t a l l a t i o n f o r L o c a l a n d R em o t e M o n i t o r i n g
Tele Eye RX U s er G u i d e
[B A U D RA T E ]
[RI NG
RG59 cable
MO D EM
P a g e 51
11.a.4. Select
and then
C O U NT ] option press “E n ter ” button
B A UD R A TE 5 7 6 0 0 B PS
R I NG C O UNT 1
11.a.5. Use “U p ” or “D ow n ” button to set
number. Press “E n ter ” button to input baud
rate and ring count setting
11.b: Conf igure TeleEye R X transmitter modem connection setting through PC
C C T V
M o n i t o r
P o w er A d ap t er
T elep h o n e cable
RS 2 3 2 s er i al cable
TeleEye R X
RG59 cable
C am er as
Telephone
N et w or k
T elep h o n e cable
M o d em
M o d em
M o d em S et u p f o r W i n d o w s 20 0 0 / X P o f P C
11.b.1. I n W indow s 2000/ X P desktop, select S ta r t >
C on tr ol P a n el
11.b.2. Double click A dd H ardw are, press Nex t, to
search the modem connected to the PC
automatically
RS 2 3 2 s er i al cable
B a s i c I n s t a l l a t i o n f o r L o c a l a n d R em o t e M o n i t o r i n g
Tele Eye RX U s er G u i d e
11.b.3. W indow s 2000/ X P can search the modem device
automatically . I f modem installation has
problem, please ref er to the modem manual.
11.b.4. A f ter searching the modem, W indow s 2000/ X P
can install the modem driver automatically . Press
[F in is h ] button to exit the menu. The modem is
ready to use.
P a g e 52
11.b.5. Run W X -30 sof tw are w hich has been installed to
the PC. (For details of W X -30 sof tw are
installation, please ref er to W X -30 Sof tw are
G uide)
B a s i c I n s t a l l a t i o n f o r L o c a l a n d R em o t e M o n i t o r i n g
Tele Eye RX U s er G u i d e
Tele
Eye
R X
11.b.6. Choose [T r a n s m itter ] [Reg is tr a tion ] to
register the
to input transmitter serial number and
registration code.
For example :
S er ia l No. : VTC12345
Reg is tr a tion C ode : 1234567890
11.b.7. Press [C on n ect] icon to pop up the
[C on n ect W in dow ]. For example, ty pe and
select the f ollow ing setting :
P h on e/ I P :
29955992 (Phone number of the transmitter)
C on n ect U s in g :
U.S. Robotics 56K Voice EX T PnP
(M odem Driver)
P a s s w or d: 000000
transmitter. User needs
P a g e 53
11.b.8. Press [C on n ect] icon to connect y our
PC and the transmitter. The video appears on the
W X -30 if success. O therw ise, the [W a r n in g ]
board w ill pop up and show y ou f ailure message.
For f ailure case, please press [C on n ect]
icon to check that the connection setting is valid
or not.
11.b.9. Press [T r a n s m itter s etu p ] icon to show
TeleEye R X conf iguration menu.
11.b.10. Select [C on n ection ] and press [M odem
S ettin g s ] icon to conf igure
netw ork setting.
B a s i c I n s t a l l a t i o n f o r L o c a l a n d R em o t e M o n i t o r i n g
Tele Eye RX U s er G u i d e
S ta r t
Nex t
11.b.11. A ssign modem baud rate in order to adj ust
modem connection speed.
11.b.12. A ssign ring count, so modem can connect to the
transmitter af ter that ring count.
P a g e 54
11.b.13. Press [A p p l y ] icon to save the
netw ork setting and pop up the message board.
A f ter several seconds, the transmitter w ill restart
automatically .
12. I f user setup modem connection by using local CCTV monitor (Step 11a), please install the
modem f or y our PC and connect to the telephone netw ork in order to connect to TeleEye
R X transmitter
12.1 I n W indow s 2000/ X P desktop, select
>
C on tr ol P a n el
12.2 Double click A dd H ardw are, press
, to
search the modem connected to the PC
automatically
B a s i c I n s t a l l a t i o n f o r L o c a l a n d R em o t e M o n i t o r i n g
Tele Eye RX U s er G u i d e
[F in is h ]
[C on n ect W in dow ]
12.3 W indow s 2000/ X P can search the modem device
automatically . I f modem installation has
problem, please ref er to the modem manual.
12.4 A f ter searching the modem, W indow s 2000/ X P
can install the modem driver automatically . Press
button to exit the menu. The modem is
ready to use.
P a g e 55
12.5 Run W X -30 sof tw are w hich has been installed to
the PC. (For details of W X -30 sof tw are
installation, please ref er to W X -30 Sof tw are
G uide)
12.6 Press [C on n ect] icon to pop up the
. For example, ty pe and
select the f ollow ing setting :
P h on e/ I P :
29955992 (Phone number of the transmitter)
C on n ect U s in g :
U.S. Robotics 56K Voice EX T PnP
(M odem Driver)
P a s s w or d: 000000
B a s i c I n s t a l l a t i o n f o r L o c a l a n d R em o t e M o n i t o r i n g
Tele Eye RX U s er G u i d e
P a g e 56
12.7 Press [C on n ect]
PC and the transmitter. The video appears on the
W X -30 if success. O therw ise, the [W a r n in g ]
board w ill pop up and show y ou f ailure message.
For f ailure case, please press [C on n ect]
icon to check that the connection setting is valid
or not.
icon to connect y our
B a s i c I n s t a l l a t i o n f o r L o c a l a n d R em o t e M o n i t o r i n g
Tele Eye RX U s er G u i d e
P a g e 57
SECTION 4
Basic Operation for L ocal and
R em ote M onitoring
A. L o c a l C C T V M o n i t o r : L i v e M o n i t o r i n g , R e c o r d i n g
a n d P l a y b a c k
1. L i v e Mo n i t o r i n g
Press “S cr een C on tr ol ” buttons to view the live video in f ull, q uad, 3 x 3 (RX 368/ 3616
only ), hex (RX 3616 only ) and seq uential display mode.
FULL
SEQ UEN TI A L
Q UA D
3X 3
f or R X 364, FULL, Q UA D and SEQ UEN TI A L buttons are available
f or R X 368, FULL, Q UA D, 3X 3 and SEQ UEN TI A L buttons are available
f or R X 3616, FULL, Q UA D, 3X 3, H EX and SEQ UEN TI A L buttons are available
Press “L iv e C a m er a C on tr ol ” buttons to f ast sw itch to a specif ic camera f or local
monitoring
H EX
f or R X 364, buttons 1-4 are available
f or R X 368, buttons 1-8 are available
f or R X 3616, buttons 1-16 are available
B a s i c L o c a l O p er a t i o n : L i v e M o n i t o r i n g , R ec o r d i n g a n d P l a yb a c k
Tele Eye RX U s er G u i d e
R EC O R D I NG
R E C O R D IN G C A M E R A
1 - 3 -
R EC O R D I NG
2. Re c o r d i n g
P a g e 58
1. Press “Rec”
STA R T R EC O R D I NG ENTER
w ill pop up.
R EC C A MER A - - - -
2. Select [RE C C A M E RA ] option and press “E n ter ”
STA R T SC H ED UL E R EC ENTER
button and [RE C O RD I NG ] menu
button to enable recording cameras.
3. Use “L ef t” or “Rig h t” button to select
the recording camera and use “U p ” or “D ow n ”
button to enable or disable the recording camera.
4. Step 4: A f ter setting the recording cameras, press
STA R T R EC O R D I NG ENTER
“E n ter ” button to save the setting and back to
R EC C A MER A 1 - 3 –
[RE C O RD I NG ] menu.
STA R T SC H ED UL E R EC ENTER
(e.g. Cam 1 & 3 are enabled, Cam 2 & 4 are
di s abled)
5. Select [S T A RT RE C O RD I NG ] option and press
“E n ter ”
button f or recording. The { Rec L E D }
w ill be turned O N (RED Color) w hich indicates
that recording is processing.
6. Press “Rec” button again to stop recording
f unction and the { RE C L E D } w ill be turned O FF.
B a s i c L o c a l O p er a t i o n : L i v e M o n i t o r i n g , R ec o r d i n g a n d P l a yb a c k
Tele Eye RX U s er G u i d e
R EC O R D I NG L O G
1 2 – 1 3 A UG 2 0 0 5
PL A Y
R EC O R D I NG L O G
1 2 – 1 3 A UG 2 0 0 5
PL A Y
P l a y b a c k
1. Press “S ea r ch ”
[RE C O RD I NG L O G ] board on O SD.
2. Press “P l a y / E n ter ” button to show [P L A Y ]
T IM E S E A R C H
menu.
M O N T H L O G
D A Y L O G
3. Select [M I NU T E L O G ] option and press
H O U R L O G
10M IN L O G
M IN U T E L O G
“E n ter ” button.
[RE C O RD I NG L O G ] board w ill show the log
TI ME C A MER A EV ENT R EMA R K SENSO R
1 1 : 5 4 1 2 3 4 - - - - - - - - - - - - - - -
1 1 : 5 5 1 2 3 4 - - - - - - - - - - - - - - - - - - - -
1 1 : 5 6 1 2 3 4 - - - - - - - - - - - - - - 1 1 : 5 7 1 2 3 4 - - - - - - - - - - - - - - 1 1 : 5 8 1 2 3 4 - - - - - - - - - - - - - - 1 1 : 5 9 1 2 3 4 - - - - - - - - - - - - - - -
in minute scale.
4. Select a record and press “E n ter ” button f or
play back.
button to pop up
P a g e 59
TI ME C A MER A EV ENT R EMA R K SENSO R
1 1 : 0 0 1 2 3 4 - - - - - - - - - - - - - - -
1 2 : 0 0 - - - 4 - - - - - - - - - - - - - - - - - - - -
1 3 : 0 0 - - - - - - - - - - - - - - - - - - 1 4 : 0 0 - 2 - - - - - - - - - - - - - - - - 1 5 : 0 0 - - - - - - - - - - - - - - - - - - 1 6 : 0 0 1 - - - - - - - - - - - - - - - - - -
Then [P L A Y B A C K] menu w ill pop up again.
T IM E S E A R C H
5. Select [P L A Y ] option and press “E n ter ”
M O N T H L O G
button again f or play back.
D A Y L O G
H O U R L O G
10M IN L O G
M IN U T E L O G
B a s i c L o c a l O p er a t i o n : L i v e M o n i t o r i n g , R ec o r d i n g a n d P l a yb a c k
Tele Eye RX U s er G u i d e
6. Using “P l a y b a ck C on tr ol b u tton ” f or
P l a y
These icons will shown on OSD for playback
st at u s
P a u s e
R e w i n d
F o r w a r d
P a g e 60
F a s t f o r w a r d
S t e p f o r w a r d
S t e p b a c k w a r d
7. Press “s cr een con tr ol ” or “ca m er a
con tr ol ” buttons to
change the view mode in local CCTV video
play back.
B . TeleE y e R X R e c e p t i o n S o f t w a r e W X - 3 0 : L i v e
M o n i t o r i n g , R e c o r d i n g a n d P l a y b a c k
1. L i v e Mo n i t o r i n g
User can view a particular camera by simply clicking the camera button (e.g. 1, 2 or 3) on
the camera control panel, or view all cameras, click [A l l ]
B a s i c L o c a l O p er a t i o n : L i v e M o n i t o r i n g , R ec o r d i n g a n d P l a yb a c k
icon.
Tele Eye RX U s er G u i d e
Screen view s in Full screen
Screen view s in Q uarter screen
Screen view s in H ex screen
A uto-arrange can optimise the screen
view s in order to display as many highresolution pictures as possible.
User can change TeleEye R X Reception Sof tw are
W X -30 live monitoring q uality by f ollow ing steps.
1. Click [T r a n s m itter S ettin g s ] icon at the
sof tw are f ront panel.
2. Enter the a dm in is tr a tor p a s s w or d to proceed.
3. A transmitter settings menu w ill pop up.
4. Choose video properties under [v ideo in p u t] to
change the b r ig h tn es s , con tr a s t and col or
level.
P a g e 61
5. Choose [Recor din g ] to change the recording
q uality and resolution.
B a s i c R em o t e O p er a t i o n : L i v e M o n i t o r i n g , R ec o r d i n g a n d P l a yb a c k
Tele Eye RX U s er G u i d e
2 . Re c o r d i n g
P a g e 62
1. Press [Recor d]
icon to setup recording
setting.
2. I nput administrator passw ord (0 0 0 0 0 0 as def ault
passw ord) and press [O K] button.
3. Enable recording cameras ( Tick f or enable,
blank f or disable)
4. Press [S ta r t Recor din g ] icon to
start recording
Recording
f u nct ion is running
B a s i c R em o t e O p er a t i o n : L i v e M o n i t o r i n g , R ec o r d i n g a n d P l a yb a c k
Tele Eye RX U s er G u i d e
3 . P l a y b a c k
P a g e 63
1. Press [P l a y ]
icon to show play back menu
2. Select and input the record date and time f or
searching and press [Rel oa d]
icon.
3. Select a tim e s l ot r ecor d and press [S ta r t
P l a y b a ck ] button.
4. Use “p l a y b a ck con tr ol b u tton ” to
control play back video such as “p l a y ”, “p a u s e”,
“f or w a r d”, “b a ck w a r d” and “s top ” f unction.
5. Press [A l l ] , [F u l l s cr een ] , [Q u a r ter
s cr een ] , [3 X 3 s cr een ] , [H ex s cr een ]
or [A u to- a r r a n g e] icon to change the
view mode f or play back.
Note: A f ter p r e s s i n g “ pause” b u tton f or 1 m i n u te, r ec ep ti on s of tw a r e W X - 3 0 w i l l c on ti n u e to
p l a y b a c k th e v i d eo a u tom a ti c a l l y .
Note: I f u s er r ec or d v i d eo b y u s i n g q u a d r ec or d i n g m od e, th e p l a y b a c k v i d eo q u a l i ty m a y n ot b e
g ood a s i n f u l l s c r een d i s p l a y m od e.
B a s i c R em o t e O p er a t i o n : L i v e M o n i t o r i n g , R ec o r d i n g a n d P l a yb a c k
Tele Eye RX U s er G u i d e
OS D M enu Operation
A. H o w t o u s e O S D m e n u
1. Press the “M en u ” button to open the main menu
2. Using the “U p ” / “D ow n ” button to select a sub-menu
3. A selected sub-menu option w ill be pointed by a hand cursor and highlighted
P a g e 64
SECTION 5
4. Press “E n ter ” button to conf irm the selection and open the sub-menu
5. I f menu option ends w ith [. . .] indicates sub-menu existing, y ou can alw ay s press the
“E n ter ” button to open the sub-menu.
6. I f menu option does not end w ith [. . .] but provides selection, user can press the “L ef t”
/ “Rig h t” button to select the options.
7. Y ou can press the “B a ck ”
8. Press “L iv e” button or “B a ck ” button until O SD disappears to exit menu and
save the setting. [S E T T I NG S A V E D ] message w ill be show n.
button once back to previous menu.
O S D M en u O p er a t i o n
Tele Eye RX U s er G u i d e
M A IN M E N U
S E T U P M E N U
B . M a i n M e n u
The M ain menu allow s user to setup and control the transmitter, some operations such as
backup, sw itch, scandisk and f ormat can be done in the main menu.
Ma i n Me n u
S E T U P . . .
B A C K U P T O C D - R . . .
S W IT C H C O N T R O L . . .
S C A N / F O R M A T D IS K . . .
T R A N S M IT T E R IN F O . . .
L O C K K E Y S E N T E R
S H U T D O W N E N T E R
S E T U P : Change the TeleEye R X transmitter setting
B A C KU P T O C D R : Backup recorded video to CD-R or CD-RW
S W I T C H C O NT RO L : Turn on / of f sw itch 1-4
S C A N / F O RM A T D I S K : Show the hard disk inf ormation, do scandisk and
f ormat the hard disk operation
T RA NS M I T T E R I NF O : Show the TeleEye R X transmitter inf ormation
L O C K KE Y S : Lock the panel key s
S H U T D O W N : Shut dow n or restart Te le Eye R X transmitter
P a g e 65
V ID E O . . .
R E C O R D IN G . . .
S W IT C H E S . . .
D A T E / T IM E . . .
C O N N E C T IO N . . .
E V E N T H A N D L E R . . .
T R A N S M IT T E R . . .
PA S S W O R D . . .
R E S T O R E F A C T O R Y S E T T IN G E N T E R
Ma i n Me n u S e t u p
V I D E O : Change camera, local monitoring, PTZ setting, O SD
color and video f ormat related settings
RE C O RD I NG : Change recording related settings
S W I T C H E S : Change sw itches related settings
D A T E / T I M E : Change date and time settings
C O NNE C T I O N : Change connection and netw ork related settings
E V E NT H A ND L E R : Change event related settings
T RA NS M I T T E R : Change the transmitter name, registration checking
and perf orm f irmw are upgrade
P A S S W O RD : Change the passw ord
RE S T O RE F A C T O RY S E T T I NG : Restore def ault f actory setting
O S D M en u O p er a t i o n
Tele Eye RX U s er G u i d e
V ID E O
C A M E R A S E T T IN G
C A M E R A
1
S E T T IN G
Ma i n Me n u S e t u p V i d e o
C A M E R A S E T T IN G . . .
L O C A L M O N IT O R IN G . . .
O S D C O L O R B L U E
V ID E O F O R M A T PA L
C A M E RA S E T T I NG : Change camera name and install camera
L O C A L M O NI T O RI NG : Change local CCTV monitor related setting
O S D C O L O R : Change O SD color
V I D E O F O RM A T : Change the video f ormat to PA L or N TSC f ormat
Ma i n Me n u S e t u p V i d e o Ca m e r a S e t t i n g
C A M E R A 1 . . .
C A M E R A 2 . . .
C A M E R A 3 . . .
C A M E R A 4 . . .
.
.
.
C A M E R A 13 . . .
C A M E R A 14 . . .
C A M E R A 15 . . .
C A M E R A 16 . . .
P a g e 66
Note: Nu m b er of i tem s i n th i s m en u d ep en d s on tr a n s m i tter m od el .
Ma i n Me n u S e t u p V i d e o Ca m e r a S e t t i n g Ca m e r a 1 S e t t i n g
IN S T A L L E D Y E S
N A M E C A M E R A 1
S U PPO R T PT Z Y E S
G E N E R A L PT Z S E T T IN G . . .
I NS T A L L E D : I nstall the camera
NA M E : Edit the camera name
S U P P O RT P T Z : Enable the PTZ camera
G E NE RA L P T Z S E T T I NG : Change PTZ camera setting
O S D M en u O p er a t i o n
Tele Eye RX U s er G u i d e
G E N E R A L PT Z S E T T IN G
PT Z M O V E M E N T S E T T IN G
D W E L L T IM E
2
Ma i n Me n u S e t u p V i d e o Ca m e r a S e t t i n g Ca m e r a X S e t t i n g
G e n e r a l P T Z S e t t i n g
PA N S PE E D F A S T
T IL T S PE E D F A S T
PT Z M O V E M E N T S E T T IN G . . .
A D V A N C E PT Z S E T T IN G . . .
P A N S P E E D : Select the pan (horiz ontal direction) speed of the
PTZ camera
T I L T S P E E D : Select the tilt (vertical direction) speed of the PTZ
camera
P T Z M O V E M E NT S E T T I NG : Change the PTZ camera movement duration
A D V A NC E P T Z S E T T I NG : Change the PTZ camera driver and baud rate
P a g e 67
Ma i n Me n u S e t u p V i d e o Ca m e r a S e t t i n g Ca m e r a X S e t t i n g
G e n e r a l P T Z S e t t i n g P T Z Mo v e m e n t S e t t i n g
PA N D U R A T IO N 5
T IL T D U R A T IO N 5
Z O O M D U R A T IO N 3
F O C U S D U R A T IO N 3
IR IS D U R A T IO N 3
A D D IT IO N A L D U R A T IO N 3
W A S H E R D U R A T IO N 3
W IPE R D U R A T IO N 3
PA T R O L S PE E D 3
P A N D U RA T I O N : Select the PTZ camera pan duration
T I L T D U RA T I O N : Select the PTZ camera tilt duration
Z O O M D U RA T I O N : Select the PTZ camera z oom duration
F O C U S D U RA T I O N : Select the PTZ camera f ocus duration
I RI S D U RA T I O N : Select the PTZ camera iris duration
A D D I T I O NA L D U RA T I O N : Select the PTZ camera additional duration if any
W A S H E R D U RA T I O N : Select the PTZ camera w asher duration
W I P E R D U RA T I O N : Select the PTZ camera w iper duration
P A T RO L S P E E D : Select the PTZ camera patrol speed
D W E L L T I M E : Select the PTZ camera dw ell time
O S D M en u O p er a t i o n
Tele Eye RX U s er G u i d e
L O C A L M O N IT O R IN G
A D V A N C E PT Z S E T T IN G
Ma i n Me n u S e t u p V i d e o Ca m e r a S e t t i n g Ca m e r a X S e t t i n g
G e n e r a l P T Z S e t t i n g A d v a n c e P T Z S e t t i n g
PT Z D R IV E R T E L E E Y E D M 4 . . .
B IT R A T E 9 600
P T Z D RI V E R : Select the PTZ camera driver
B I T RA T E : Select the PTZ camera bit rate
Ma i n Me n u S e t u p V i d e o L o c a l Mo n i t o r i n g
C L O C K PO S IT IO N B O T T O M
C A M E R A N A M E PO S IT IO N T O P
S E Q U E N T IA L S W IT C H T IM E 1S E C
S E Q U E N T IA L M O D E C A M E R A S 1- 3D E F A U L T D IS PL A Y M O D E Q U A D
H O R IZ O N T A L PO S IT IO N 5
V E R T IC A L PO S IT IO N 0
H O R IZ O N T A L S C A L E 10
V E R T IC A L S C A L E 2
P a g e 68
C L O C K P O S I T I O N : Change the clock position
C A M E RA NA M E P O S I T I O N : Change the camera name position
S E Q U E NT I A L S W I T C H T I M E : Change the sw itch time betw een each live
camera display f or seq uential mode monitoring
S E Q U E NT I A L M O D E C A M E RA S : Select cameras f or seq uential mode monitoring
D E F A U L T D I S P L A Y M O D E : Select def ault display mode in CCTV monitor
af ter TeleEye R X transmitter boot up
H O RI Z O NT A L P O S I T I O N : Change horiz ontal position of local video output
V E RT I C A L P O S I T I O N : Change vertical position of local video output
H O RI Z O NT A L S C A L E : Change horiz ontal scale of local video output
V E RT I C A L S C A L E : Change vertical scale of local video output
For [H O RI Z O NT A L P O S I T I O N], [V E RT I C A L P O S I T O N], [H O RI Z O NT A L S C A L E ]
and [V E RT I C A L S C A L E ] options, change these options if live video position or siz e display
does not f it in the local CCTV monitor.
O S D M en u O p er a t i o n
Tele Eye RX U s er G u i d e
R E C O R D IN G
RECORDING
Ma i n Me n u S e t u p Re c o r d i n g
R E C O R D IN G M O D E C O N T IN U O U S
D IS K M O D E C Y C L IC
Q U A L IT Y E X C E L L E N T
IM A G E S IZ E F U L L
S C H E D U L E R E C O R D IN G . . .
R E C O R D IN G R E T E N T IO N . . .
R E C O V E R R E C O R D IN G E N T E R
RE C O RD I NG M O D E : Change recording mode in 1, 2, 3, 4, 5 f rame per
D I S K M O D E : Select the f ix or cy clic disk mode
Q U A L I T Y : Change recording q uality w ith 5 levels
I M A G E S I Z E : Change recording video siz e in dif f erent modes
S C H E D U L E RE C O RD I NG : Set up a recording schedule up to 1 w eek
RE C O RD I NG RE T E NT I O N : Set a retention period f or recording
RE C O V E R RE C O RD I NG : Recover damaged recording log.
P a g e 69
second (FPS) and continuous setting
Note: R ec or d i n g i n c y c l i c d i s k m od e c a n er a s e th e ol d es t r ec or d i n g d a ta i n h a r d d i s k i f th e
h a r d d i s k i s f u l l , w h er ea s r ec or d i n g w i l l b e s top p ed i n f i x d i s k m od e
Recor din g S ch edu l er
Recording scheduler allow s users to record video w ith user selected time. I t supports 2
modes of schedule recording: normal recording and motion recording.
Nor m a l ty p e:
The transmitter records video w ith user selected time. Continuous, 1FPS, 2FPS, 3FPS,
4FPS and 5FPS f rame rate can be chosen in normal recording mode.
M otion ty p e:
The transmitter records video of a camera if the selected motion block in the camera
detects motion during user selected time. M otion recording only provides 1FPS and
continuous recording f rame rate.
A d d i n g S c h ed u l e I n C a l en d a r V i ew
1. Press “M en u ”
button, select [S E T U P ] option and
press “E n ter ” button to enter [S E T U P ] sub
menu. Select [RE C O RD I NG ] option and press
“E n ter ”
button, then select [S C H E D U L E D
RECORDING M ODE CONT INU OU S
DISK M ODE CY CL IC
Q U A L IT Y EXCEL L ENT
IM A GE SIZ E F U L L
SCH EDU L ED RECORDING . . .
RECORDING RET ENT ION . . .
RE C O RD I NG ] option and press “E n ter ” button
to show recording scheduler menu.
O S D M en u O p er a t i o n
SU NDA Y
OPT ION
A DD SCH EDU L E
SCH EDU L E W EEK DA Y
Tele Eye RX U s er G u i d e
A DD
L IST V IEW
2. Calendar View of recording schedule is show n. Press
H OU R T IM E SCA L E CA M ERA
“E n ter ”
0 0 : 0 0 – – – –
0 2 : 0 0 – – – –
0 4 : 0 0 – – – –
0 6 : 0 0 – – – –
0 8 : 0 0 – – – –
10 : 0 0 – – – –
12 : 0 0 – – – –
14 : 0 0 – – – –
16 : 0 0 – – – –
18 : 0 0 – – – –
20 : 0 0 – – – –
22 : 0 0 – – – –
button to add schedule or change view .
: REC
: M OT ION REC
P a g e 70
3. Select [A D D ] option and press “E n ter ”
button to
add a new recording schedule.
4. Select [T Y P E ] option to choose schedule recording
T Y PE REC
ty pe. Set [RE C ] f or normal schedule recording. Set
W EEK DA Y S S– – – – – –
ST A RT T I M E 0 0 : 0 0
[M O T I O N RE C ] f or motion schedule recording.
END T IM E 0 2 : 0 0
CA M ERA 1234
F RA M E RA T E CONT INU OU S
GENERA L M OT ION SET T ING . . .
A PPL Y ENT ER
5. Select [W E E KD A Y S ] and press “E n ter ” button
S M T W T F S
to select the day of time slot added in a w eek. Use
“U p ” or “D ow n ” button to enable the day .
From the lef t to right, the day options are Sunday
(S), M onday (M ), Tuesday (T), W ednesday (W ),
Thursday (T), Friday (F) and Saturday (S). Press
“E n ter ” button to apply the w eekday s setting.
O S D M en u O p er a t i o n
Tele Eye RX U s er G u i d e
T I M E
A DD SCH EDU L E
A DD SCH EDU L E
A PPL Y
ENT ER
A DD SCH EDU L E
6. I n [A D D S C H E D U L E ] menu, select [S T A RT
T I M E ] and [E ND T I M E ] to choose the time
0 2 : 0 0
interval f or the schedule recording. Press “E n ter ”
P a g e 71
button and use “U p ” or “D ow n ” button to
select the time. A time slot is minimum 10 m in u tes
long. Finally , press “E n ter ” button to apply the
time settings.
7. I n [A D D S C H E D U L E ] menu, select [C A M E RA ]
T Y PE M OT ION REC
W EEK DA Y S SM T W T F S
ST A RT T I M E 0 0 : 0 0
or [F RA M E RA T E ] to choose the f rame rate or
END T IM E 0 2 : 0 0
camera respectively .
CA M ERA 1234
F RA M E RA T E CONT INU OU S
GENERA L M OT ION SET T ING . . .
A PPL Y ENT ER
8. I f user selects motion recording in [T Y P E ] option,
T Y PE M OT ION REC
user should set motion settings in [G E NE RA L
W EEK DA Y S SM T W T F S
M O T I O N S E T T I NG ] option.
ST A RT T I M E 0 0 : 0 0
END T IM E 0 2 : 0 0
CA M ERA 1234
F RA M E RA T E CONT INU OU S
GENERA L M OT ION SET T ING
. . .
Note that :
I f [ E ND T I M E ] i s earli er t h an [ S T A R T
T I M E ] , i t w i ll as s u me t h e end t i me i s o n
nex t day .
E .g. M o nday , s t art t i me : 18 : 0 0 , end t i me :
0 9 : 0 0
T h e s c h edu le p eri o d i s f ro m M o nday 18 : 0 0
t o T u es day 0 9 : 0 0 .
9. Select the motion camera and press “E n ter ”
10. Select [A P P L Y ] and press “E n ter ” button to
T Y PE M OT ION REC
save the recording schedule setting of the time slot.
W EEK DA Y S SMTWTFS
ST A RT T I M E 0 0 : 0 0
END T IM E 0 2 : 0 0
CA M ERA 1234
F RA M E RA T E CONT INU OU S
GENERA L M OT ION SET T ING . . .
A PPL Y
ENT ER
O S D M en u O p er a t i o n
ST A RT RECORDING
OPT ION
Tele Eye RX U s er G u i d e
A DD
L IST V IEW
← S U N D A Y →
H O U R T IM E S C A L E C A M E R A
00: 00 1235467 8 9 A B C D E F G
02: 00 1235467 8 9 A B C D E F G
04: 00 1235467 8 9 A B C D E F G
06: 00 1235467 8 9 A B C D E F G
08 : 00 1235467 8 9 A B C D E F G
10: 00 1235467 8 9 A B C D E F G
12: 00 1235467 8 9 A B C D E F G
14: 00 1235467 8 9 A B C D E F G
16: 00 1235467 8 9 A B C D E F G
18 : 00 1235467 8 9 A B C D E F G
20: 00 1235467 8 9 A B C D E F G
22: 00 1235467 8 9 A B C D E F G
: R E C : M O T IO N R E C
R ed blo c k means t h e t i mes lo t i s s et t o no rmal
rec o rdi ng.
G reen blo c k means t h e t i me s lo t i s s et t o mo t i o n
rec o rdi ng.
O nly o ne rec o rdi ng t y p e c an be s et i n o ne t i me s lo t
P a g e 72
O ne blo c k o f t i me s lo t o n
c alendar v i ew rep res ent s a
10 mi nu t e s c h edu le, s o o ne ro w
rep res ent s 2- h o u r s c h edu le.
T h e ro w rep res ent s a p eri o d o f
8 : 0 0 - 10 : 0 0
R ed nu mbers means t h e
c ameras i s no rmal rec o rdi ng.
G reen nu mbers means t h e
c ameras i s mo t i o n rec o rdi ng
W h i t e nu mbers means t h e
c ameras are s et t o mo t i o n
and no rmal i n t h e s ame ro w ,
i .e. w i t h i n 2 h o u rs .
11. Press “L iv e”
button to exit O SD menu or press
“B a ck ” button to enter action menu again.
Press “Recor d” button to enter [RE C O RD I NG ]
ST A RT RECORDING ENT ER
REC. CA M ERA 1234
menu. Select [S T A RT S C H E D U L E ] and press
ST A RT SCH EDU L E REC ENT ER
“E n ter ” button to activate recording scheduler
R ec o r d i n g S c h ed u l er i n L i st V i ew
1. I n calendar view , press “E n ter ” button to pop
up [O P T I O N] menu. Select [L I S T V I E W ] and
press “E n ter ” button to enter list view .
O S D M en u O p er a t i o n
SU NDA Y
SU NDA Y
A DD
REM OV E OPT ION
REM OV E SEL ECT ED
Tele Eye RX U s er G u i d e
A DD
REM OV E
REM OV E
REM OV E DA Y
EDIT
EDIT
REM OV E W EEK
COPY
COPY
CA NCEL
CA L ENDA R V IEW
CA L ENDA R V IEW
2. List view schedule is show n. The schedule in list
ST A RT END CA M ERA F PS
view is same as the schedule in calendar view .
0 0 : 0 0 0 9 : 0 0 1234 C
0 9 : 0 0 10 : 0 0 12– 4 2
10 : 0 0 12 : 0 0 1– 3– 1
Press “E n ter ”
12 : 0 0 14 : 0 0 12– – 3
menu.
14 : 0 0 16 : 0 0 1– 3– 4
16 : 0 0 18 : 0 0 1– 34 5
18 : 0 0 19 : 0 0 1234 C
19 : 0 0 22 : 0 0 1234 1
22 : 0 0 0 0 : 0 0 1– 34 C
button to pop up [O P T I O N]
P a g e 73
: REC
: M OT ION REC
3. I n [O P T I O N] menu of list view , user can add,
remove, edit or copy schedule in list view . Select
[C A L E ND A R V I E W ] and press “E n ter ”
button to return to calendar view .
R em o v i n g S c h ed u l e P r o c ed u r e
1. I n list view , select the time slot that y ou w ould
like to remove.
ST A RT END CA M ERA F PS
0 0 : 0 0 0 9 : 0 0 1234 C
0 9 : 0 0 10 : 0 0 12– 4 2
10 : 0 0 12 : 0 0 1– 3– 1
12 : 0 0 14 : 0 0 12– – 3
14 : 0 0 16 : 0 0 1– 3– 4
16 : 0 0 18 : 0 0 1– 34 5
18 : 0 0 19 : 0 0 1234 C
19 : 0 0 22 : 0 0 1234 1
22 : 0 0 0 0 : 0 0 1– 34 C
: REC
: M OT ION REC
2. Press “E n ter ” button to pop up [O P T I O N]
menu. Select [RE M O V E ] and press “E n ter ”
button to pop up [RE M O V E O P T I O N] menu.
3. Select [RE M O V E S E L E C T E D ] to remove the
selected schedule. User may choose [RE M O V E
D A Y ] to remove all schedules f or the w hole day .
O r, choose [RE M O V E W E E K] to remove all
schedules in a w eek. Select [C A NC E L ] to exit
the menu w ithout removing schedule.
O S D M en u O p er a t i o n
A DD
EDIT SCH EDU L E
SU NDA Y
SU NDA Y
REM OV E
Tele Eye RX U s er G u i d e
Ed i t i n g S c h ed u l e P r o c ed u r e
EDIT
COPY
CA L ENDA R V IEW
1. I n list view , select a time slot that y ou w ould like to
edit.
P a g e 74
ST A RT END CA M ERA F PS
0 0 : 0 0 0 9 : 0 0 1234 C
0 9 : 0 0 10 : 0 0 12– 4 2
10 : 0 0 12 : 0 0 1– 3– 1
12 : 0 0 14 : 0 0 12– – 3
14 : 0 0 16 : 0 0 1– 3– 4
16 : 0 0 18 : 0 0 1– 34 5
18 : 0 0 19 : 0 0 1234 C
19 : 0 0 22 : 0 0 1234 1
22 : 0 0 0 0 : 0 0 1– 34 C
2. Press “E n ter ” button to pop up [O P T I O N]
menu. Select [E D I T ] and press “E n ter ” button
to pop up [E D I T S C H E D U L E ] menu.
3. I n [E D I T S C H E D U L E ] menu, user can change
recording ty pe, camera and f rame rate of that
T Y PE M OT ION REC
schedule. I f the schedule is motion recording, user
CA M ERA 1234
F RA M E RA T E CONT INU OU S
should change other motion settings.
GENERA L M OT ION SET T ING . . .
A f ter changing the settings, select [A P P L Y ] and
A PPL Y ENT ER
press “E n ter ”
button to save the new schedule
settings.
: REC
: M OT ION REC
C o p yi n g S c h ed u l e P r o c ed u r e
1. I n list view , select the time slot that y ou w ould
like to copy .
ST A RT END CA M ERA F PS
0 0 : 0 0 0 9 : 0 0 1234 C
0 9 : 0 0 10 : 0 0 12– 4 2
10 : 0 0 12 : 0 0 1– 3– 1
12 : 0 0 14 : 0 0 12– – 3
14 : 0 0 16 : 0 0 1– 3– 4
16 : 0 0 18 : 0 0 1– 34 5
18 : 0 0 19 : 0 0 1234 C
19 : 0 0 22 : 0 0 1234 1
22 : 0 0 0 0 : 0 0 1– 34 C
: REC
: M OT ION REC
O S D M en u O p er a t i o n
A DD
COPY SCH EDU L E
RECORDING
RECORDING RET ENT ION
REM OV E
Tele Eye RX U s er G u i d e
EDIT
COPY
CA L ENDA R V IEW
P a g e 75
Press “E n ter ”
button to pop up [O P T I O N] menu.
Select [C O P Y ] option and press “E n ter ” button to
pop up [C O P Y S C H E D U L E ] menu.
2. I n [C O P Y S C H E D U L E ] menu, select [C O P Y
S C H E D U L E S ] option and user should set
[S I NG L E S C H E D U L E ] to copy the selected
COPY SCH EDU L ES SINGL E SCH EDU L E
COPY T O W EEK DA Y S X– – – – – –
schedule of the day or set [E NT I RE D A Y ] to
A PPL Y ENT ER
copy all schedules of the day .
3. Select [C O P Y T O W E E KD A Y S ] option to set
the day that the schedule copies to. Select
[A P P L Y ] option and press “E n ter ” button to
copy the schedule.
R ec o r d i n g R et en t i o n
This f irmw are of TeleEye R X transmitter supports passw ord protection f or all menus, Sy stem
administrator can setup a passw ord to protect the transmitter f rom being operated by
unauthoriz ed operators
R ec o r d R et en t i o n S et u p P r o c ed u r e
1. Press “M en u ”
RECORDING M ODE CONT INU OU S
option and press “E n ter ” button to enter
DISK M ODE CY CL IC
Q U A L IT Y EXCEL L ENT
[S E T U P ] sub menu. Select
IM A GE SIZ E F U L L
[RE C O RD I NG ] option and press “E n ter ”
SCH EDU L ED RECORDING . . .
RECORDING RET ENT ION . . .
button, select [S E T U P ]
button, then select [RE C O RD
RE T E NT I O N] option and press “E n ter ”
button to show [RE C O RD I NG
RE T E NT I O N] menu.
2. I n [RE C O RD I NG RE T E NT I O N] menu,
user and enable/ disable this f unction, set
ENA BL E Y ES
retention period and schedule time f or
RET ENT ION PERIOD ( DA Y S) 9 9 9
SCH EDU L E T IM E F OR RET ENT ION 0 8 : 0 0
retention. Press “E n ter ” button af ter
selecting [RE T E NT I O N P E RI O D
( D A Y S )] / [S C H E D U L E T I M E F O R
RE T E NT I O N] and use “U p ”
“D ow n ” button to select the period /
time.
O S D M en u O p er a t i o n
or
Tele Eye RX U s er G u i d e
S W IT C H E S
S W IT C H
1
S E T T IN G
T Y PE
L A T C H IN G
D A T E / T IM E
Ma i n Me n u S e t u p S w i t c h e s
S W IT C H 1 S E T T IN G . . .
S W IT C H 2 S E T T IN G . . .
S W IT C H 3 S E T T IN G . . .
S W IT C H 4 S E T T IN G . . .
Change the sw itch setting by choosing “S W I T C H 1, 2 , 3 a n d 4”
Ma i n Me n u S e t u p S w i t c h e s S w i t c h 1 S e t t i n g
N A M E S W IT C H 1
P a g e 76
NA M E : Edit the name of the sw itch
T Y P E : Change the ty pe of the sw itch, either l a tch in g or
p u s h - b u tton ty pe
Ma i n Me n u S e t u p D a t e T i m e S e t u p
T IM E S Y N C E N A B L E D Y E S
T IM E Z O N E . . .
D A T E 11 M A R 2006
T IM E 11 : 03
PR I T IM E S E R V E R T IM E . W IN D . .
S E C T IM E S E R V E R T IM E . N IS T . .
D N S S E T T IN G . . .
U PD A T E D A T E / T IM E E N T E R
S T A T U S
T I M E S Y NC E NA B L E D : Enable/ Disable time sy nchroniz ation
T I M E Z O NE : Change the time z one
D A T E : Set the current date
T I M E : Set the current time
P RI T I M E S E RV E R : Set a primary time server
S E C T I M E S E RV E R : Set a secondary time server
D NS S E T T I NG : Change the netw ork setting
U P D A T E D A T E / T I M E : Update date/ time f rom server
S T A T U S : Show the status of time sy nc
O S D M en u O p er a t i o n
Tele Eye RX U s er G u i d e
Mo d i f y sy st e m t i m e
1. Sy stem date and time can only be modif ied w hen T I M E S Y NC is disabled.
P a g e 77
2. Press “E n ter ”
D A T E
3. Press “L ef t”
button to select [D A T E T I M E ] or [T I M E ] option
D A T E
2 4 A U G 2 0 0 5
T IM E
T IM E
/ “Rig h t” button to select date, month, y ear f or [D A T E T I M E ] or
select hour, minutes f or [T I M E ] option
4. Press “U p ” / “D ow n ” button to change the value
5. Press “E n ter ” button to save setting and exit this page of menu
Ma i n Me n u S e t u p D a t e / T i m e T i m e Z o n e
1. Select a corresponding time z one w ill
enable Day light saving f unction.
2. Press “L ef t” / “Rig h t”
button to select betw een time z ones
(G M T).
3. Press “U p ” / “D ow n ” button to
select betw een dif f erent cities
4. Press “E n ter ”
button to save setting
and back to previous menu.
.
G M T + 08 : 00 .
A N T A R C T IC A / C A S E Y
A S IA / B R U N E I
A S IA / C H O N G Q IN G
A S IA / C H U N G K IN G
A S IA / H A R B IN
A S IA / H O N G _ K O N G
A S IA / IR K U T S K
A S IA / K A S H G A R
A S IA / K U A L A _ L U M PU R
A S IA / K U C H IN G
A S IA / M A C A O
A S IA / M A C A U
←G M T + 08 : 00→
1 5 : 1 8
PA G E 1/ 3
O S D M en u O p er a t i o n
Tele Eye RX U s er G u i d e
C O N N E C T IO N
T C P / IP
S U R E L IN K
Ma i n Me n u S e t u p Co n n e c t i o n
T C P / IP …
M O D E M …
T H R O U G H PU T …
T C P / I P : Conf igure T C P / I P netw ork related setting
M O D E M : Conf igure modem related setting
T H RO U G H P U T : Conf igure throughput control setting
Ma i n Me n u S e t u p Co n n e c t i o n T CP / IP
IP 19 2.168 .0.2
PO R T 1024
S U B N E T M A S K 255.255.255.0
E N A B L E G A T E W A Y N O
G A T E W A Y 0.0.0.0
E N A B L E D N S N O
PR IM A R Y D N S 0.0.0.0
S E C O N D A R Y D N S 0.0.0.0
S U R E L IN K …
P a g e 78
I P : Change TeleEye R X transmitter I P
P O RT : Change TeleEye R X transmitter port
S U B NE T M A S K : Change TeleEye R X transmitter subnet mask
E NA B L E G A T E W A Y : Enable TeleEye R X transmitter gatew ay setting
G A T E W A Y : Change TeleEye R X transmitter gatew ay
E NA B L E D NS : Enable TeleEye R X transmitter DN S setting
P RI M A RY D NS : Change TeleEye R X transmitter primary DN S
S E C O ND A RY D NS : Change TeleEye R X transmitter secondary DN S
S U RE L I NK : Change TeleEye R X transmitter sureL I N K setting
Ma i n Me n u S e t u p Co n n e c t i o n T CP / IP sureL IN K
E N A B L E D Y E S
S U R E L IN K A D D R E S S W W W . . . . .
R E F R E S H R A T E 15 M IN S
E NA B L E D : Enable sureL I N K option
S U RE L I NK A D D RE S S : Change the TeleEye R X transmitter sureL I N K
address
RE F RE S H RA T E : Select the sureL I N K ref resh rate
O S D M en u O p er a t i o n
Tele Eye RX U s er G u i d e
E V E N T H A N D L E R
Ma i n Me n u S e t u p Co n n e c t i o n Mo d e m
M O D E M
B A U D R A T E 57 600 B PS
R IN G C O U N T 1
B A U D RA T E : Change the baud rate of the modem
RI NG C O U NT : Change the ring count to connect to the modem
Ma i n Me n u S e t u p Co n n e c t i o n T h r o u g h p u t
T H R O U G H PU T
L A N S T R E A M 100M B PS
B R O A D B A N D S T R E A M 40M B PS
N A R R O W B A N D S T R E A M 128 K B PS
B PS : B IT PE R S E C O N D
P a g e 79
L A N S T RE A M : Change the data rate of LA N connection
B RO A D B A ND S T RE A M : Change the data rate of broadband connection
NA RRO W B A ND S T RE A M : Change the date rate of narrow band connection
Ma i n Me n u S e t u p E v e n t H a n d l e r
A R M / D IS A R M . . .
S E C U R IT Y S W IT C H . . .
A L A R M . . .
M O T IO N . . .
V ID E O L O S S . . .
S Y S T E M T A M PE R . . .
PO W E R F A IL U R E . . .
D IS K U S A G E . . .
O V E R H E A T . . .
The event handler menu contain 9 f unctions (A RM / D I S A RM , S E C U RI T Y S W I T C H ,
A L A RM , M O T I O N, V I D E O L O S S , S Y S T E M T A M P E R, P O W E R F A I L U RE , D I S K
U S A G E and O V E RH E A T )
O S D M en u O p er a t i o n
Tele Eye RX U s er G u i d e
T R A N S M IT T E R
F IR M W A R E U PG R A D E
PA S S W O R D M E N U
Ma i n Me n u S e t u p T r a n sm i t t e r
T R A N S M IT T E R N A M E R X 364
R E G IS T R A T IO N C H E C K IN G Y E S
B U IL T - IN W E B S E R V E R N O
U PG R A D E . . .
T RA NS M I T T E R NA M E : Edit the transmitter name
RE G I S T RA T I O N C H E C KI NG : Check if the serial number of the transmitter match
the serial number registered in the reception
sof tw are W X -30 or not
B U I L T - I N W E B S E RV E R : Change the status of built-in server
U P G RA D E : Upgrade new version f irmw are
Ma i n Me n u S e t u p T r a n sm i t t e r U p g r a d e
P a g e 80
U PG R A D E F R O M U S B E N T E R
U PG R A D E F R O M C D E N T E R
The new version f irmw are can be upgraded via USB or CD
Note: U s er n eed s to i n s ta l l a f or m a tted h a r d d i s k f i r s t b ef or e th e f i r m w a r e u p g r a d e th r ou g h
C D
Ma i n Me n u S e t u p P a ssw o r d
E N A B L E E V E N T M E N U PA S S W O R D N O
E N A B L E R E C O R D IN G M E N U PA S S W O R D N O
E N A B L E S E A R C H M E N U PA S S W O R D N O
E N A B L E M A IN M E N U PA S S W O R D N O
E N A B L E K E Y S L O C K E D PA S S W O R D N O
C H A N G E PA S S W O R D . . .
E NA B L E E V E NT M E NU P A S S W O RD : Change the status of event menu passw ord
E NA B L E RE C O RD I NG M E NU P A S S W O RD : Change the status of recording menu
passw ord
E NA B L E S E A RC H M E NU P A S S W O RD : Change the status of search menu passw ord
E NA B L E M A I N M E NU P A S S W O RD : Change the status of main menu passw ord
E NA B L E KE Y S L O C KE D P A S S W O RD : Change the status of key s locked passw ord
C H A NG E P A S S W O RD : Setup a new passw ord
* N o t e : d e f a u l t p a s s w o r d = 1 1 1 1 1 1
O S D M en u O p er a t i o n
Tele Eye RX U s er G u i d e
B A C K U P T O C D R
S W IT C H E S
B A C K
S W IT C H E S
B A C K
Ma i n Me n u Ba c k u p t o CD - R
S T A R T D A T E 01 A U G 2005
S T A R T T IM E 15: 08
B A C K U P S IZ E ( M B ) 650
S T A R T B A C K U P E N T E R
S T A RT D A T E : Set the start date of the f ootage
S T A RT T I M E : Set the start time of the f ootage
B A C KU P S I Z E : Set the backup siz e (10M B ~ 650 M B)
S T A RT B A C KU P : Start Backup CD-R operation, and TeleEye R X
transmitter w ill search the f ootages f rom start date
and time and calculate the end time of f ootage
according to the f ootages siz e and backup siz e.
Ma i n Me n u S w i t c h Co n t r o l
P a g e 81
U S E C A M K E Y S T O
C O N T R O L S W IT C H E S
N O N A M E O N O F F
1 S W IT C H 1 O F F
2 S W IT C H 2 O F F
3 S W IT C H 3 O F F
4 S W IT C H 4 O F F
N O N A M E O N O F F
1 S W IT C H 1 O N
2 S W IT C H 2 O N
3 S W IT C H 3 O N
4 S W IT C H 4 O N
U S E C A M K E Y S T O
C O N T R O L S W IT C H E S
The sw itches can be controlled by pressing the cam key s (1, 2, 3 and 4) respectively . A nd the
screen w ill show the current status (O N / O FF) of sw itches
S W I T C H 1 : Control by cam key 1
S W I T C H 2 : Control by cam key 2
S W I T C H 3 : Control by cam key 3
S W I T C H 4 : Control by cam key 4
O S D M en u O p er a t i o n
Tele Eye RX U s er G u i d e
S C A N / F O R M A T D IS K
T R A N S M IT T E R IN F O R M A T IO N
Ma i n Me n u S c a n / F o r m a t D i sk
M A S T E R H D D
M O D E L N O M A X T O R X X X X
S E R IA L N O X X X X X X X
C A PA C IT Y 41G B
S L A V E N / A
M O D E L N O
S E R IA L N O
C A PA C IT Y
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - D IS K U S A G E 52%
S C A N D IS K E N T E R
F O R M A T E N T E R
M A S T E R/ S L A V E : Show the device ty pe
M O D E L NO : Show the device model no.
S E RI A L NO : Show the device serial no.
C A P A C I T Y : Show the capacity of the device
D I S K U S A G E : Show the disk usage in percentage
S C A ND I S K : Start H DD scanning operation
F O RM A T : Start H DD f ormatting operation
P a g e 82
Ma i n Me n u T r a n sm i t t e r In f o r m a t i o n
T R A N S M IT T E R N A M E R X 364
T R A N S M IT T E R IP 19 2.168 .0.2
M O D E L N O . R X 364
S E R IA L N O . V T C X X X X X
V E R S IO N 01.00
T RA NS M I T T E R NA M E : Show the transmitter name
T RA NS M I T T E R I P : Show the transmitter I P address
M O D E L NO . : Show the transmitter model no.
S E RI A L NO . : Show the transmitter serial no.
V E RS I O N : Show the transmitter f irmw are version
O S D M en u O p er a t i o n
Tele Eye RX U s er G u i d e
RECORDING L OG
12 – 13 A U G20 0 5
L O C K K E Y S
K E Y L O C K E D
Ma i n Me n u L o c k K e y s
L O C K K E Y S E N T E R
A U T O K E Y L O C K 15S E C
L O C K KE Y S : Lock all key s on the f ront panel
A U T O KE Y L O C K : Select auto key lock duration, key s on f ront panel
w ill be automatically locked up if no button is being
pressed w ithin the selected period.
U N L O C K ?
Y E S N O
P a g e 83
W hen the key s are being locked, pressing any key on the f ront panel the sy stem w ill show a
message to conf irm the unlock operation. Select “Y ES” to unlock the key s , “N O ” to keep the
key s locked.
C. R e c o r d i n g L o g M e n u
T IM E CA M ERA EV ENT REM A RK SENSOR M OT ION A U DIO V IDEOL OSS
11 : 0 0 1234 - - - - - - - - - - - - - - - - - - - - - - - - 12 : 0 0 - - - 4 - - - - - - - - - - - - - - - - - - - - - - - - 13 : 0 0 - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
14 : 0 0 - 2 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
15 : 0 0 - - - - - - - - - - - - - - - - - - - - - - - - - - - - 16 : 0 0 1 - - - - - - - - - - - - - - - - - - - - - - - - - - - 17 : 0 0 1 - - - - - - - - - - - - - - - - - - - - - - - - - - - -
T I M E : Show date of log
C A M E RA : Show time of log
E V E NT : Show event triggered
RE M A RK : I tems are not available now
S E NS O R : Show alarm sensor triggered
M O T I O N : Show motion trigger in w hich camera
A U D I O : Show audio channel
V I D E O L O S S : Show camera video loss
O S D M en u O p er a t i o n
Tele Eye RX U s er G u i d e
T IM E S E A R C H
PL A Y
P a g e 84
1. Press “E n ter ” button to choose play recording log, time search f unction and log time
scale
2. Press the “B a ck ” button to exit the recording log menu
T IM E S E A R C H
M O N T H L O G
D A Y L O G
H O U R L O G
10M IN L O G
M IN U T E L O G
P L A Y : Play the current selected record
T I M E S E A RC H : Search specif y time recording log and play it
M O NT H L O G : Change the recording log scale to month
D A Y L O G : Change the recording log scale to day
H O U R L O G : Change the recording log scale to hour
10 M I N L O G : Change the recording log scale to 10 minutes
M I NU T E L O G : Change the recording log scale to 1 minute
Re c o r d i n g L o g Me n u T i m e S e a r c h
D A T E 13 S E P 2005
T IM E 10 : 30
C A M E R A 1234
S E A R C H
D A T E : Select the date of record
T I M E : Select the time of record
C A M E RA : Select the camera of record
S E A RC H : Search the record
E N T E R
O S D M en u O p er a t i o n
IRIS - < > +
RECA L L PRESET NO.
F OCU S - < > +
RECA L L PRESET
PROGRA M PRESET
RECA L L PA T ROL
Tele Eye RX U s er G u i d e
ST OP PA T ROL
A U X PA N
IRIS CT RL
F OCU S CT RL
A U X CT RL
P a g e 85
D . P T Z M e n u
1. For any camera supports PTZ , [P T Z O P T I O N] menu alw ay s pops up w hen user press the
“L iv e” button. User selects [D I S A B L E P T Z ] to disable PTZ f unction.
2. Using the “U p ” / “D ow n ” button to select each option
P T Z Co n t r o l In t e r f a c e
PTZ sy mbol w ill f lash near the camera name on the O SD f or current controlling PTZ
camera. User can use f ront panel to pref orm pan / tilt / z oom action of the selected PTZ
supported camera any time w hen live monitoring on O SD.
P T Z Co n t r o l Me t h o d :
1. Press “L iv e” button to pop up PTZ control options.
Select any options and press “E n ter ”
pop up.
2. For example, [I RI S C T RL ] is selected. I ris control
menu w ill pop up. Use “L ef t” or “Rig h t”
button to control - or + the value respectively .
3. To Recall Preset, Program Preset and Recall Patrol
options, Press “L iv e C a m er a C on tr ol B u tton s ” to
select preset numbers.
button to
Use “U p ” , “D ow n ” buttons to select other PTZ
camera control as example on the lef t.
E . R e c o r d i n g M e n u
O S D M en u O p er a t i o n
Tele Eye RX U s er G u i d e
R E C O R D IN G
R E C O R D IN G C A M E R A
E V E N T M E N U
S T A R T R E C O R D IN G E N T E R
S T A R T S C H E D U L E R E C E N T E R
P a g e 86
R E C C A M E R A - - - -
1. Press the “Rec”
button to pop up the main menu
2. Using the “U p ” / “D ow n ” button to select recording and set recording camera
S T A RT RE C O RD I NG : Start recording operation
RE C O RD I NG C A M E RA : Select the camera f or recording
S T A RT S C H E D U L E RE C : Start scheduled recording
Re c o r d i n g Me n u Re c o r d i n g Ca m e r a
1 - 3 -
1. Using the “L ef t” / “Rig h t” button to select camera
2. Press the “U p ” / “D ow n ” button to enable or disable camera f or recording
3. Press “E n ter ” button to conf irm the selection. Press the “B a ck ” button to exit
w ithout saving any recording camera setting
F . E v e n t M e n u
1. Press the “E v en t” button to pop up the event menu
2. Using the “U p ” / “Dow n” button to select a sub-menu
3. A selected sub-menu option w ill be pointed by a hand cursor and highlighted
O S D M en u O p er a t i o n
E V E N T S T A T U S . . .
E V E N T L O G . . .
C O N N E C T IO N L O G . . .
S E T T IN G L O G . . .
O PE R A T IO N L O G . . .
Tele Eye RX U s er G u i d e
E V E N T S T A T U S
C L E A R E V E N T
E N T E R
P a g e 87
4. Press “E n ter ”
button to conf irm the selection and pop up the sub-menu
E V E NT S T A T U S : Show event status
E V E NT L O G : Show the event log
C O NNE C T I O N L O G : Show the remote connection log
S E T T I NG L O G : Show the setting log
O P E RA T I O N L O G : Show the operation log
1. I f menu option end w ith [ . . .] indicates sub-menu existing, y ou can alw ay s press “E n ter ”
button to pop up the sub-menu.
2. Y ou can press the “B a ck ” button back to previous menu and “L iv e” button to exit
menu.
E v e n t Me n u E v e n t S t a t u s
A L A R M 1234
M O T IO N 12
V ID E O L O S S - - 34
D IS K F U L L N O R M A L
O V E R H E A T N O R M A L
T A M PE R S Y S / A R M S E C S W
PO W E R F A IL U R E F A IL
A L A RM : Show the alarm status
M O T I O N : Show the motion status
V I D E O L O S S : Show the video loss status
D I S K F U L L : Show the hard disk status
O V E RH E A T : Show the overheat status
S Y S T E M F A I L U RE : Show the sy stem status
T A M P E R : Show the arm, security sw itch and sy stem tamper
status
P O W E R F A I L U RE : Show the status of pow er f ailure input
C L E A R E V E NT : Clear event
O S D M en u O p er a t i o n
Tele Eye RX U s er G u i d e
A L A R M L O G
E v e n t Me n u A l a r m L o g
D A T E T IM E C H A N N E L S T A T U S A C T IO N
03A U G 05 12 : 45 : 18 - - - 4 - - - - R E S E T - - - - - -
03A U G 05 12 : 29 : 46 - - - 4 - - - - T G R R- D - B- - - - - - - - -
02A U G 05 09 : 50 : 33 - - - - - - - - A R M - - - - - 02A U G 05 09 : 35 : 02 - 2 - - - - - - T A M PE R - - - E - 01A U G 05 11 : 05 : 03 - - - - - - - - S S O N - - - - - 01A U G 05 10 : 25 : 36 1 - - - - - - - R E S E T - - - - - 01A U G 05 10 : 10 : 10 1 - - - - - - - T G R - S- E - P
01A U G 05 09 : 29 : 17 - - - - - - - - E N T R Y - - - - - -
D A T E : Show the date log
T I M E : Show the time log
C H A NNE L : Show the event number (alarm / motion & videoloss only )
S T A T U S : Show the status. Full description of status is show n as f ollow :
Display Description
TG R Event trigger
TA M PER A larm tampered
RESET Event reset
CLEA R User clear event status
A RM Sy stem is armed
DI SA RM Sy stem is disarmed
SS O N Security sw itch turned on
SS O FF Security sw itch turned of f
EN TRY Event trigger during entry delay time
EX I T Event trigger during exit delay time
P a g e 88
A C T I O N : Show the event associated action
Display Description
R Recording
S Sw itch
D Dial back
E E-mail notif ication
B Buz z er
P Recall Preset PTZ position
L A ssociate camera to local monitor
O S D M en u O p er a t i o n
Tele Eye RX U s er G u i d e
C O N N E C T IO N L O G
SET T ING L OG
P a g e 89
E v e n t Me n u Co n n e c t i o n L o g
D A T E T IM E U S E R R E M A R K IP/ PH O N E N O D E V IC E S T A T U S
22A U G 05 12 : 45 : 18 A D M IN - - - - 19 2.168 .0.2 T C P / IP D IS C O N N E C T E D
22A U G 05 12 : 29 : 46 A D M IN D IA L IN 19 2.168 .0.2 T C P / IP C O N N E C T E D
21A U G 05 09 : 50 : 33 A D M IN - - - - 19 2.168 .0.2 T C P / IP D IS C O N N E C T E D
21A U G 05 09 : 35 : 02 A D M IN D IA L B A C K 19 2.168 .0.2 T C P / IP C O N N E C T E D
20A U G 05 11 : 05 : 03 A D M IN - - - - 19 2.168 .0.2 T C P / IP D IS C O N N E C T E D
20A U G 05 10 : 25 : 36 A D M IN D IA L B A C K 19 2.168 .0.2 T C P / IP C O N N E C T E D
20A U G 05 10 : 10 : 10 A D M IN - - - - 19 2.168 .0.2 T C P / IP D IS C O N N E C T E D
20A U G 05 09 : 29 : 17 A D M IN D IA L B A C K 19 2.168 .0.2 T C P / IP C O N N E C T E D
D A T E : Show the date log
T I M E : Show the time log
U S E R : Show the user ty pe connected to the transmitter
through remote sof tw are
RE M A RK : Show the connection triggered by user or dialback
action
DI A L I N Remote connect to transmitter
DI A L BA CK Transmitter connect to remote
I P / P H O NE NO . : Show the I P or phone number of the remote host
D E V I C E : Show connection method by the remote sof tw are
S T A T U S : Show the connection status
E v e n t Me n u S e t t i n g L o g
DA T E T IM E OPERA T ION CH A NNEL REM A RK DEV ICE IP / PH ONE NO
0 3DEC0 5 12 : 45 : 18 A L A RM SEN T Y PE - - - 4 NC T CP / IP 19 2.16 8 . 0 . 2
0 3DEC0 5 12 : 29 : 46 M OT ION - - - 4 ENA BL ED L OCA L 0 . 0 . 0 . 0
0 2DEC0 5 0 9 : 50 : 33 RECORD M ODE - - - - CONT INU OU S L OCA L 0 . 0 . 0 . 0
0 2DEC0 5 0 9 : 35 : 0 2 V IDEOL OSS - 2 - - ENA BL ED L OCA L 0 . 0 . 0 . 0
0 1DEC0 5 11 : 0 5 : 0 3 V IDEO F ORM A T - - - - NT SC T CP / IP 19 2.16 8 . 0 . 2
0 1DEC0 5 10 : 25 : 36 A L A RM T M R T Y PE 1 - - - DEOL T CP / IP 19 2.16 8 . 0 . 2
0 1DEC0 5 10 : 10 : 10 A L A RM 1 - - - ENA BL ED L OCA L 0 . 0 . 0 . 0
0 1DEC0 5 0 9 : 29 : 17 CA M ERA - - 3 - INST A L L ED L OCA L 0 . 0 . 0 . 0
D A T E : Show the date log
T I M E : Show the time log
O P E RA T I O N : Show the setting that w as done by user (Please ref er
to the A ppendix)
C H A NNE L : Show the channel f or the setting, such as alarm
sensor number, camera number
RE M A RK : Show the set value of the setting
D E V I C E : Show the setting that w as done by w hich ty pe of user
I P / P H O NE NO : Show the I P or phone number f or the remote user
O S D M en u O p er a t i o n
Tele Eye RX U s er G u i d e
S E A R C H L O G
L O G O PT IO N
OPERA T ION L OG
E v e n t Me n u O p e r a t i o n L o g
DA T E T IM E OPERA T ION DEV ICE IP / PH ONE NO
0 3DEC0 5 12 : 45 : 18 ST OP PL A Y BA CK T CP / IP 19 2.16 8 . 0 . 2
0 3DEC0 5 12 : 29 : 46 ST A RT PL A Y BA CK L OCA L 0 . 0 . 0 . 0
0 2DEC0 5 0 9 : 50 : 33 ST OP RECORDING L OCA L 0 . 0 . 0 . 0
0 2DEC0 5 0 9 : 35 : 0 2 ST A RT RECORDING L OCA L 0 . 0 . 0 . 0
0 1DEC0 5 11 : 0 5 : 0 3 ST OP PL A Y BA CK L OCA L 0 . 0 . 0 . 0
0 1DEC0 5 10 : 25 : 36 ST A RT PL A Y BA CK T CP / IP 19 2.16 8 . 0 . 2
0 1DEC0 5 10 : 10 : 10 ST OP RECORDING L OCA L 0 . 0 . 0 . 0
0 1DEC0 5 0 9 : 29 : 17 ST A RT RECORDING T CP / IP 19 2.16 8 . 0 . 2
D A T E : Show the date log
T I M E : Show the time log
O P E RA T I O N : Show the operation done by user (Please ref er to the
A ppendix)
D E V I C E : Show the setting done by w hich ty pe of user
I P / P H O NE NO : Show the I P or phone number f or the remote user
P a g e 90
S e a r c h L o g
For each log, y ou can press “E n ter ”
button in [T I M E S E A RC H ] option to enter search log menu.
T IM E S E A R C H
E V E N T PL A Y B A C K
The connection log contains the f ollow ing options
D A T E : Set the search date
T I M E : Set the search time
S E A RC H : Search the nearest record according to the da te and
button to enter the log option, and press “E n ter ”
D A T E 20 S E P 2005
T IM E 10 : 19
S E A R C H E N T E R
tim e
O S D M en u O p er a t i o n
Tele Eye RX U s er G u i d e
EV ENT L OG
A L A RM L OG
L OG OPT ION
P l a y i n g c o r r e sp o n d i n g f o o t a g e f r o m e v e n t L o g
Event log play back supports user to play back the video directly f rom selected event log.
Event Log Playback Pr oced u r e :
P a g e 91
1. Press “E v en t”
button to pop up the
event menu. Select [E V E NT L O G ]
option and press “E n ter ”
button to
view all kinds of event logs.
2. For example, selecting [A L A RM L O G ]
DA T E T IM E CH A NNEL ST A T U S A CT ION
0 3A U G0 5 12 : 45 : 18 - - - 4 - - - - RESET - - - - - -
and press “E n ter ” button to enter
0 3A U G0 5 12 : 29 : 46 - - - 4 - - - - T GR R- D - B-
0 2A U G0 5 0 9 : 50 : 33 - - - - - - - - A RM - - - - - -
alarm log menu.
0 2A U G0 5 0 9 : 35 : 0 2 - 2 - - - - - - T A M PER - - - E - 0 1A U G0 5 11 : 0 5 : 0 3 - - - - - - - - SS ON - - - - - 0 1A U G0 5 10 : 25 : 36 1 - - - - - - - RESET - - - - - 0 1A U G0 5 10 : 10 : 10 1 - - - - - - - T GR - S- E - P
0 1A U G0 5 0 9 : 29 : 17 - - - - - - - - ENT RY - - - - - -
A L A RM L OG . . .
M OT ION L OG . . .
V IDEO L OSS L OG . . .
SY ST EM T A M PER L OG . . .
A RM DISA RM T A M PER L OG . . .
SECU . SW IT CH T A M PER L OG . . .
POW ER F A IL U RE L OG . . .
DISK U SA GE L OG . . .
OV ERH EA T L OG . . .
3. I n the alarm log menu, press “E n ter ”
button to pop up [L O G O P T I O N] menu.
I f there exists a corresponding recording
T I M E SEA RCH
event, [E V E NT P L A Y B A C K] option
EV ENT PL A Y BA CK
w ill be included in the [L O G O P T I O N]
menu f or play back the video.
4. Select [E V E NT P L A Y B A C K] and press
“E n ter ” button to w atch the play back
f or this event.
O S D M en u O p er a t i o n
Tele Eye RX U s er G u i d e
P a g e 92
SECTION 6
Advanced Operation
A . I n s t a l l TeleE y e R X w i t h A l a r m S e n s o r s a n d R e l a y
Co n t r o l P o r t
TeleEye RX 3 64/ 3 68 / 3 616 support up to 4/ 8/ 16 alarm ports in that order w ith tamper detection
f or connecting w ith alarm sensors, 4 additional input sensors and 4 relay ports f or control. The
def initions of alarm and relay control ports are show n in the f ollow ing diagram.
P i n a ssi g n m en t f o r TeleEye R X 364
Pin 1 A L A R M 1 Pin 2 0 G N D
Pin 2 A L A R M 2 Pin 2 1 G N D
Pin 3 A L A R M 3 Pin 2 2 G N D
Pin 4 A L A R M 4 Pin 2 3 G N D
Pin 5 N / A Pin 2 4 G N D
Pin 6 N / A Pin 2 5 G N D
Pin 7 N / A Pin 2 6 G N D
Pin 8 N / A Pin 2 7 G N D
Pin 9 N / A Pin 2 8 A R M / D I S A R M
Pin 10 N / A Pin 2 9 S E C U R I T Y S W I T C H
Pin 11 N / A Pin 3 0 PO W E R F A I L U R E
Pin 12 N / A Pin 3 1 S Y S T E M T A M PE R
Pin 13 N / A Pin 3 2 N / A
Pin 14 N / A Pin 3 3 N / A
Pin 15 R E L A Y 0 a Pin 3 4 R E L A Y 0 b
Pin 16 R E L A Y 1a Pin 3 5 R E L A Y 1b
Pin 17 R E L A Y 2 a Pin 3 6 R E L A Y 2 b
Pin 18 R E L A Y 3 a Pin 3 7 R E L A Y 3 b
Pin 19 N / A
I n s t a l l TeleEye R X w i t h A l a r m S en s o r s a n d R el a y C o n t r o l P o r t
Tele Eye RX U s er G u i d e
P i n a ssi g n m en t f o r TeleEye R X 368
Pin 1 A L A R M 1 Pin 2 0 G N D
Pin 2 A L A R M 2 Pin 2 1 G N D
Pin 3 A L A R M 3 Pin 2 2 G N D
Pin 4 A L A R M 4 Pin 2 3 G N D
Pin 5 A L A R M 5 Pin 2 4 G N D
Pin 6 A L A R M 6 Pin 2 5 G N D
Pin 7 A L A R M 7 Pin 2 6 G N D
Pin 8 A L A R M 8 Pin 2 7 G N D
Pin 9 N / A Pin 2 8 A R M / D I S A R M
Pin 10 N / A Pin 2 9 S E C U R I T Y S W I T C H
Pin 11 N / A Pin 3 0 PO W E R F A I L U R E
Pin 12 N / A Pin 3 1 S Y S T E M T A M PE R
Pin 13 N / A Pin 3 2 N / A
Pin 14 N / A Pin 3 3 N / A
Pin 15 R E L A Y 0 a Pin 3 4 R E L A Y 0 b
Pin 16 R E L A Y 1a Pin 3 5 R E L A Y 1b
Pin 17 R E L A Y 2 a Pin 3 6 R E L A Y 2 b
Pin 18 R E L A Y 3 a Pin 3 7 R E L A Y 3 b
Pin 19 N / A
P i n a ssi g n m en t f o r TeleEye R X 3616
P a g e 93
Pin 1 A L A R M 1 Pin 2 0 G N D
Pin 2 A L A R M 2 Pin 2 1 G N D
Pin 3 A L A R M 3 Pin 2 2 G N D
Pin 4 A L A R M 4 Pin 2 3 G N D
Pin 5 A L A R M 5 Pin 2 4 G N D
Pin 6 A L A R M 6 Pin 2 5 G N D
Pin 7 A L A R M 7 Pin 2 6 G N D
Pin 8 A L A R M 8 Pin 2 7 G N D
Pin 9 A L A R M 9 Pin 2 8 A R M / D I S A R M
Pin 10 A L A R M 10 Pin 2 9 S E C U R I T Y S W I T C H
Pin 11 A L A R M 11 Pin 3 0 PO W E R F A I L U R E
Pin 12 A L A R M 12 Pin 3 1 S Y S T E M T A M PE R
Pin 13 A L A R M 13 Pin 3 2 A L A R M 14
Pin 14 A L A R M 15 Pin 3 3 A L A R M 16
Pin 15 R E L A Y 0 a Pin 3 4 R E L A Y 0 b
Pin 16 R E L A Y 1a Pin 3 5 R E L A Y 1b
Pin 17 R E L A Y 2 a Pin 3 6 R E L A Y 2 b
Pin 18 R E L A Y 3 a Pin 3 7 R E L A Y 3 b
Pin 19 N / A
I n s t a l l TeleEye R X w i t h A l a r m S en s o r s a n d R el a y C o n t r o l P o r t
Tele Eye RX U s er G u i d e
R 6 K
R 6 K
P a g e 94
B . I n s t a l l TeleE y e R X w i t h T a m p e r Ci r c u i t a n d
E x t e r n a l R e s i s t o r s
TeleEye R X supports tamper detection (DEO L and SEO L) on all alarm inputs including
arm/ disarm input, security sw itch input, sy stem tamper and pow er f ailure input.
D E O L : D u a l E n d of L in e ter m in a tion w ith NC a n d NO con n ection
S E O L : S in g l e E n d of L in e ter m in a tion w ith NC a n d NO con n ection
NC / NO : A l a r m a n d oth er in p u t p or ts w ith ou t ta m p er detection cir cu it con n ection
For example, by connecting the tamper circuit w ith DEO L, the circuit is in the normal close
condition if the resistance betw een point A and B detects 1.2kΩ (show n as below ), w hereas the
circuit is in normal open condition if the resistance betw een point A and B (show n as below )
detects 7.2kΩ .The resistance transition f rom 1.2kΩ to 7.2kΩ is generated by an alarm tamper
event f or normal close circuit. The setup conf iguration of those alarms and input ports are show n
in the f ollow ing diagram. The circuit debouncing time betw een each sensor is 20 millisecond.
D u a l En d o f L i n e C o n f i g u r a t i o n
A
R 1 . 2 K
s en s o r
d riv e
o u t p u t
C
B
N o r m a l C l o s e ( N C )
A
R 1 . 2 K
C
s en s o r
d riv e
o u t p u t
B
N o r m a l O p e n ( N O )
wire
wire
T e r m S t a t u s D e s c r i p t i o n
S / C T A M P E R W i r e s h o r t ( p o i n t A a n d B )
L o Z N O R M A L S e n s o r d r i v e o u t p u t c l o s e ( p o i n t B a n d
C )
H i Z A L A R M S e n s o r d r i v e o u t p u t o p e n ( p o i n t B a n d
C )
O / C T A M P E R W i r e o p e n ( p o i n t A a n d B )
T e r m S t a t u s D e s c r i p t i o n
S / C T A M P E R W i r e s h o r t ( p o i n t A a n d B )
L o Z A L A R M S e n s o r d r i v e o u t p u t c l o s e ( p o i n t B a n d
C )
H i Z N O R M A L S e n s o r d r i v e o u t p u t o p e n ( p o i n t B a n d
C )
O / C T A M P E R W i r e o p e n ( p o i n t A a n d B )
I n s t a l l TeleEye R X w i t h T a m p er C i r c u i t a n d Ex t er n a l R es i s t o r s
Tele Eye RX U s er G u i d e
S i n g l e En d o f L i n e C o n f i g u r a t i o n
P a g e 95
C
A
T e r m S t a t u s D e s c r i p t i o n
s en s o r
d riv e
o u t p u t
N o r m a l C l o s e ( N C )
s en s o r
d riv e
o u t p u t
B
A
B
wire
wire
N o r m a l O p e n ( N O )
S / C T A M P E R W i r e s h o r t ( p o i n t A a n d B )
L o Z N O R M A L S e n s o r d r i v e o u t p u t c l o s e ( p o i n t
O / C A L A R M S e n s o r d r i v e o u t p u t o p e n ( p o i n t
T e r m S t a t u s D e s c r i p t i o n
S / C A L A R M S e n s o r d r i v e o u t p u t c l o s e ( p o i n t
L o Z N O R M A L S e n s o r d r i v e o u t p u t o p e n ( p o i n t
O / C T A M P E R W i r e o p e n ( p o i n t A a n d B )
W i t h o u t T a m p er D et ec t i o n C i r c u i t C o n f i g u r a t i o n
A
T e r m S t a t u s D e s c r i p t i o n
S / C N O R M A L S e n s o r d r i v e o u t p u t c l o s e
s en s o r
d riv e
o u t p u t
N o r m a l C l o s e ( N C )
B
wire
O / C A L A R M S e n s o r d r i v e o u t p u t o p e n
B a n d C )
B a n d C )
A a n d B )
A a n d B )
( p o i n t A a n d B )
( p o i n t A a n d B )
T e r m S t a t u s D e s c r i p t i o n
S / C A L A R M S e n s o r d r i v e o u t p u t c l o s e
( p o i n t A a n d B )
s en s o r
d riv e
o u t p u t
A
wire
O / C N O R M A L S e n s o r d r i v e o u t p u t o p e n
B
( p o i n t A a n d B )
N o r m a l O p e n ( N O )
L EG EN D
N O N o r m a l l y O p e n A l a r m
N C N o r m a l l y C l o s e d A l a r m
O / C O p e n C i r c u i t
S / C S h o r t C i r c u i t
L o Z L o w I m p e d a n c e
H i Z H i g h I m p e d a n c e
Notes :
The t a b l e b el o w s ho w s t he s u m m a r y b et w een t he r es i s t a n c e n et w o r k a n d t he c o n d i t i o n r es u l t .
N o t e t ha t t hi s t a b l e i s u s ed a s a r ef er en c e. Ther e m a y b e a 1 0 % t o l er a n c e f o r t he r es i s t a n c e
v a l u e i n t he b el o w t a b l e.
I n s t a l l TeleEye R X w i t h T a m p er C i r c u i t a n d Ex t er n a l R es i s t o r s
Loading...