00P3DG090TSEB2
User’s Manual
TeleEye RN684 / RN688 / RN6816
Before using the product, please
read this manual carefully.
User’s Manual
1
Notice:
Signal Communications Limited reserves the right to make improvements to the product
described in this manual at any time and without prior notice.
This manual is copyrighted. All rights are reserved. This manual may not be copied,
reproduced or translated in whole or part without prior consent from Signal Communications
Limited.
Tele Eye is a trademark of Signal Communications Limited and is registered in China, Hong
Kong, US and other countries.
TeleEye's products are sold under the brand name of CAMERIO in Australia, Japan, Korea,
New Zealand, Taiwan and Argentina.
CAMERIO is a trademark of Signal Communications Limited and is registered in Australia,
Japan, Korea, New Zealand, Taiwan and Argentina.
All other trademarks are the property of their respective owners Copyright (c) 2007 Signal
Communications Limited (A Member of TeleEye Group). All rights reserved.
Version 2.1
Limits of Liability and Disclaimer of Warranty
Signal Communications Limited has taken care in preparation of this manual, but makes no
expressed or implied warranty of any kind and assumes no responsibility for errors or
omissions.
No liability is assumed for incidental or consequential damages in connection with or arising
out of the use of the information or accessories contained herein.
Features and specifications are subject to change without prior notice.
User’s Manual
2
Caution and Preventive Tips
• Switch the 115/230V selector to your local voltage standard
• Handle with care, do not drop the unit
• Mount the unit in an equipment rack or place it on a solid, stable surface.
• Indoor use only. Do not place the unit in a humid, dusty, oily, or smoky site.
• Do not place it in an area with poor ventilation or in an area close to fire or other sources of
heat. Doing so may damage the unit as well as cause fire or an electric shock.
• When cleaning is necessary, shut down the system and unplug the unit from the outlet
before uncovering the top cover. Do not use liquid cleaners or aerosol cleaners. Use only
a damp cloth for cleaning.
• Always shut down the system prior connecting or disconnecting accessories, with the
exception of USB devices.
• Lithium battery: Danger of explosion if battery is incorrectly replaced. Replace with the
same or equivalent type of batteries recommended by the manufacturer. Dispose used
batteries according to the battery manufacturer’s instructions.
This symbol intends to alert the user to the presence of important operating and
maintenance (servicing) instructions in the literature accompanying the
appliance.
This symbol intends to alert the user to the presence of unprotected “Dangerous
Voltage” within the product’s enclosure that may be strong enough to cause a
risk of electric shock.
User’s Manual
3
Important Information
Before proceeding, please read and observe all instructions and warnings in this manual.
Retain this manual with the original bill of sale for future reference and, if necessary, warranty
service. When unpacking your unit, check for missing or damaged items. If any item is missing,
or if damage is evident, DO NOT INSTALL OR OPERATE THIS PRODUCT. Contact your
dealer for assistance.
Rack Mounting
Consult with the supplier or manufacturer of your equipment rack for the proper hardware and
procedure of mounting this product in a safe fashion. Avoid uneven loading or mechanical
instability when rack-mounting units. Make sure that units are installed to get enough airflow for
safe operation. The maximum temperature for rack-mounted units is 40 °C. Check product
label for power supply requirements to assure that no overloading of supply circuits or over
current protection occurs. Mains grounding must be reliable and uncompromised by any
connections.
User’s Manual
4
Table of Content
1. Overview .......................................................................................................................6
2. System Setup................................................................................................................7
2.1 Position the Unit...................................................................................................7
2.2 Selecting Video Format........................................................................................7
2.3 Connecting Devices to the Unit............................................................................8
2.4 Rear Panel Connections......................................................................................8
3. General System Setup ...............................................................................................10
3.1 Front Panel Introduction ....................................................................................10
3.1.1 LED Definition ......................................................................................10
3.1.2 Function Keys.......................................................................................11
3.2 Power Up / Down the Unit .................................................................................13
3.3 Entering OSD Setup Menu ................................................................................13
3.4 System Date / Time Setting ...............................................................................14
3.4.1 Set Date / Time.....................................................................................15
3.4.2 Daylight Saving Time............................................................................16
3.4.3 Network Time Protocol Setup...............................................................17
3.5 Record Schedule / Quality Setting .....................................................................18
3.5.1 Schedule Setup....................................................................................18
3.5.2 Preset Record Configuration ................................................................19
3.5.3 To Record Event Video Only ................................................................19
3.5.4 ezRecord Setup....................................................................................19
3.5.5 Circular Recording................................................................................20
3.5.6 Purge Data ...........................................................................................21
4. Basic Operation..........................................................................................................22
4.1 Viewing Live / Playback Video...........................................................................22
4.1.1 Viewing Modes.....................................................................................22
4.1.2 Digital Zoom .........................................................................................23
4.1.3 Viewing Live Cameras..........................................................................23
To Freeze Live Image..............................................................................23
4.1.4 Viewing Recorded Video ......................................................................23
Key Usage in Playback ...........................................................................24
Pause Playback and Single Step Forward..............................................24
Viewing Live Image in Playback Mode....................................................25
4.2 Sequence Setup ................................................................................................25
4.2.1 Sequence with Main Monitor ................................................................25
4.2.2 Sequence with Call Monitor (8ch and 16ch only) .................................26
4.3 Searching Recorded Video................................................................................26
4.3.1 Searching by Time................................................................................27
User’s Manual
5
4.3.2 Searching by Event ..............................................................................27
4.4 Video Export ......................................................................................................28
4.4.1 ezBurn Introduction ..............................................................................29
4.4.2 To Export Normal Video........................................................................29
4.4.3 To Export Event Video..........................................................................30
4.5 Dome Control.....................................................................................................30
4.5.1 Dome Connection.................................................................................31
4.5.2 Dome Protocol Setup ...........................................................................31
4.5.3 RS485 Setup........................................................................................32
4.5.4 Dome Controlling Keys.........................................................................32
4.5.5 Setting Preset Points............................................................................34
4.5.6 Calling Preset Points ............................................................................35
5. Remote Monitoring Software.....................................................................................36
5.1 Remote Monitoring System Requirements ........................................................36
5.2 Getting Start of Installation.................................................................................37
5.2.1 Changing Internet Settings...................................................................37
5.2.2 Installing Remote Monitoring Software.................................................39
5.2.2.1 Log in / Log off ........................................................................40
5.2.2.2 Software Upgrades .................................................................41
5.3 Basic Operation for Monitoring remotely............................................................41
5.3.1 To View Live Video ...............................................................................42
5.3.1.1 Selecting Display Mode ..........................................................42
5.3.1.2 Operating Cameras with Dome Control ..................................43
5.3.2 Instant Recording .................................................................................44
5.3.2.1 Recording Video Instantly .......................................................44
5.3.2.2 To Playback Instant Recorded Video ......................................44
5.3.3 To Take a Snapshot ..............................................................................44
5.3.4 To Playback Video................................................................................45
5.3.4.1 Playing Back Remote Video....................................................45
5.3.4.2 To Playback Local *.drv Files ..................................................46
5.3.4.3 Playback Controls ...................................................................47
5.3.5 Search from Event List.........................................................................48
5.3.6 Remote Monitoring Software Trouble Shooting Guide .........................49
Appendix A: Technical Specifications ...........................................................................50
Appendix B: Remote Controller .....................................................................................51
Appendix C: Setting up a DVR behind a Router ...........................................................53
User’s Manual
6
1. Overview
The Proficient MPEG-4 Series DVR is an integrated digital video recorder
that combines the features of a time-lapse audio / video recorder, a
multiplexer, and a video server to create a single security CCTV solution.
Its outstanding triplex operation enables users to view live or playback
recorded video, remotely access through network simultaneously while
recording other video, and to view wanted recorded video instantly by
entering the time and date or selecting recorded video from the event list.
The DVR series unit includes the remote viewing and configuration software
that is a Web-browser plug-in, allows user to view live or recorded video
images and enables remote configuration. The remote software is stored in
the DVR series unit and deployed over a LAN, WAN or Internet connection to
remote Windows-based computers. This simplifies the installation and
maintenance of the software components so all remote users are kept up to
date.
The DVR series unit offers advanced features not typically found in standard
multiplexers; it integrates the full features of a DVR, multiplexer and video
server (by using the remote software). The key features of the DVR series
unit are listed as follows.
Advanced Functions
• Triplex Operation: Live /Playback, Record, Network
• Supports up to 2 internal HDDs
• Supports internal CD-RW
• Supports NTP for time synchronization
• Supports Mobile View software
• Multi-language support
• Multiple built-in dome camera control protocols
• Supports Pre-Alarm Recording
• Motion Detection Marker
• Remote software for remote monitoring
User’s Manual
7
Human Technology:
• ezBurn™ for quick video export
• ezRecord™ for quick recording setting
• ezDDNS™ for automatic DDNS configuration
• IR Remote Control (Optional)
• Compact Control Keyboard (Optional)
2. System Setup
The notices and introduction on system installation will be described
particularly in this chapter. Please follow the description to operate the unit.
In order to prevent the unit from data loss and system damage that caused by
a sudden power fluctuation, use of an Uninterruptible Power Supply (UPS) is
highly recommended
2.1 Position the Unit
First, note to position / mount the DVR series unit in a proper place and be
sure to power off the unit before making any connections. The placed location
should avoid hindering or blocking the unit from airflow. Enough airflow is
needed to protect the unit from overheating. The maximum allowable
temperature of operating environment is 40°C.
The unit utilizes heat-conducting techniques to transfer internal heat to the
case, especially to the bottom side of the unit.
NOTE: Be sure the rubber feet are not removed, and always leave a
space for air ventilation on the unit’s bottom side.
2.2 Selecting Video Format
The DVR series unit is designed to operate under either NTSC or PAL video
formats. The switch is positioned on the rear panel.
User’s Manual
8
2.3 Connecting Devices to the Unit
This section lists some important notices that should be read before making
any connection to the DVR series unit.
Connecting Required Devices
Before power up the unit, you should connect cameras and a main monitor to
the unit for basic operation. If needed, connect a call monitor for displaying
full screen video of all installed cameras in sequence.
Connecting Short-term Device
If you plan to install any short-term devices to the DVR series unit and use
them as part of the unit system, such as USB CD-ROM, USB Hard Disk Drive,
etc, make sure those devices are connected only after the unit is powered up.
The reason is because the DVR series unit can recognize the external
devices only after the power-up process is done completely.
2.4 Rear Panel Connections
There are various connectors on the rear panel for the DVR series unit
installations. The following figure shows the connectors by name; and
followed by the detailed description of each connector.
Main Monitor (BNC/ VGA)
BNC and VGA output connectors are offered for
connecting to a main monitor. The main monitor
displays live image and playback recorded video in
either full-screen or split-window format. VGA output
connector is optional.
Call Monitor(for 8ch and 16ch Models only)
The call monitor is used to display full screen video of
all installed cameras in sequence. The BNC call
monitor connector allows user to connect the DVR
series unit with an optional call monitor.
User’s Manual
9
Video Input
16 BNC connectors are offered for video input
streams from installed cameras. The number of
connectors is equal to the number of channels.
Alarm I/O & RS485
The unit provides an alarm I/O and RS485 port that
offers user the flexibility required to connect the unit to
the other device. The definitions for pins varies when
the DVRs have different channels. Refer to Setup
Guide for detailed pin definitions.
4ch model
8ch/16ch models
LAN Connector (RJ-45)
The DVR series unit is capable of networking. The
LAN port opens the door of the DVR series unit to
Ethernet where by the Internet.
Power Jack
The DVR series unit has a free voltage DC power
connection jack. Please connect the power adapter
that ships with the unit.
Audio In / Out
The DVR series unit provides two channels of audio
recording and playback. Audio In RCA connector is
offered for connecting an audio source device (e.g.
external amplified microphone) to the unit; Audio Out
RCA connector is offered for connecting an audio
output device (e.g. amplified speakers) to the unit.
User’s Manual
10
3. General System Setup
The DVR series unit allows user to access some general operations through
the front panel easily. The following subsections introduce the general
operations of the unit.
The regular displayed OSD information and its displayed positions are shown
as following figure. The channel title will be displayed on the top-left side of
the window, either in full screen mode or in multiple channel mode. The
current operating mode, including Call mode, Dome-Control mode, Playback
mode. Freeze mode and Sequence mode, will be displayed on the
bottom-left side of the screen. And the date/ time information will be display
on the bottom-right side.
Ch4
►*1
2005/11/09 PM04:31:22
3.1 Front Panel Introduction
The front panel controls enable user to control the unit and preset the
programmable functions.
3.1.1 LED Definition
The LEDs on the front panel of the DVR series unit are described as follows.
Power LED (Green)
The LED lights up when the correct power is connected
to the unit.
Alarm LED (Red)
The LED lights up when an alarm is triggered.
REC LED (Green)
The LED blinks while the DVR series unit is recording.
User’s Manual
11
Network LED (Green)
The LED lights up when the DVR series unit is
connected to a network and blinks when the data is
being transferred.
3.1.2 Function Keys
This section describes the functional keys, which are for normal operation, on
the front panel of the DVR series unit.
Please refer to the Setup Guide for the graphical illustration of functional
keys.
CHANNEL
• In both Live and Playback modes, press the CHANNEL key to view the
corresponding video in full screen. The number of the CHANNEL keys
corresponds to the number of cameras supported by the unit.
• In dome control mode, the key “1” is used to access the Set/Go preset
menu; the key “2” is used to hide or display the dome setting parameters.
DOME
Press the key to enter dome control mode. Please refer to Section Dome
Control for detailed controlling operation.
MODE
Press repeatedly to select for wanted main monitor display format. There are
four available view modes: full screen, 4-window (2×2), 9-window (3x3), and
16-window (4x4). Refer to Section View Modes
for detailed information.
SEQ
(Sequence)
Press to start automatic sequencing of the video coming from the installed
cameras.
MENU
Press this key to call the OSD setup menu.
User’s Manual
12
ESC
Press to cancel or exit from certain mode or OSD setup menu without
changing the settings made previously.
ZOOM/ENTER
• In OSD menu or selection interface, press this key to make the selection
or save settings.
• In live full screen view mode, press this key to view a 2× zoom image;
press it again to exit zoom mode.
COPY
In Playback mode, press COPY to select the start and end point of the video
you want to export. Refer to Section Video Export for detailed information.
PLAY/STOP
Press this key to switch between live image and playback video.
NOTE: The video of latest 5 ~ 10 minutes cannot be played back
because the video is still saved in the buffer.
FREEZE
• Press FREEZE while viewing live image, the live video will be frozen. The
date / time information shown on the monitor will continue updating. Press
FREEZE again to return to live mode.
• Press FREEZE while playing the recorded video, the playback video will
be paused. Press LEFT / RIGHT to move the recorded video reverse /
forward by single step. Press FREEZE again to continue playing video.
SEARCH
In both Playback and Live mode, the user can press SEARCH to call the
Search menu for searching and playing back recorded video by date and
time or events.
Direction Keys
• In Zoom mode, these keys function as Direction keys.
• In the OSD menu, the LEFT/ RIGHT keys are used to move the cursor to
previous or next fields. To change the value in the selected field, press
UP/ DOWN.
User’s Manual
13
3.2 Power Up / Down the Unit
If you must shut down the DVR series unit for any reason, please use the
proper shut down and power up procedures to avoid damaging your DVR unit.
To Power Up the Unit
Simply plug in the power adapter that came with the package and the DVR
will start to boot.
The color bar and system checking information will be shown on the monitor
and then disappear when the unit has been completely powered up.
To Restart / Shutdown the Unit
Press MENU and input the administrator password to access the OSD Main
menu. Select <Shutdown> in Main Menu and press ENTER to enter the
Shutdown menu, which displays as follows.
Shutdown
1. Power Off
2. Reboot
Execute
Execute
<Power Off>
Select this item to shut down the unit. Do not remove the power during shut
down until the message “You can safely turn off DVR now!” displays.
<Reboot>
Select this item to reboot the unit. The color bar and system checking
information are displayed on the monitor until the unit is completely restarted.
3.3 Entering OSD Setup Menu
The OSD Main menu contains a list of items that are used to configure the
DVR series unit. To enter the Main menu, press MENU and then enter
Administrator or User password. The Password Verification screen displays
as follows.
Password Verification
________
Press Channel Keys To Enter Password
(4-8 Digits)
Press ◄ Key To Delete
User’s Manual
14
The default passwords are shown in the following table. The same passwords
are used for entering the remote viewing software DynaRemote Lite.
Administrator Password User Password
1 2 3 4 4 3 2 1
NOTE: It is strongly suggested to change the passwords to prevent
unauthorized access to the unit.
After entering the correct password, the Main menu is displayed.
Main Menu
1. System Setup
2. Monitor Setup
3. Camera Setup
4. Record Setup
5. Sequence Setup
6. Event Setup
7. Database Setup
8. Configuration
9. Shutdown
Move the cursor up / down over the OSD items using the Direction keys and
press ENTER to enter the selected sub-menu.
3.4 System Date / Time Setting
User can set the current date, time and other OSD parameters in Date/Time
menu (under System Setup Menu). The administrator’s privileges are
required for entering the submenu. In OSD Main menu, select <System
Setup> and press ENTER, then select <Date/Time> to access the Date/Time
menu; the menu displays as follows.
Date/Time
1. Date
2. Time
3. Time Zone
4. Date/Time Display
5. Date Display Mode
6. Time Display Mode
7. Date/Time Order
8. Daylight Saving Time Setup
9. Network Time Protocol Setup
2005/02/21
PM10:39:26
OFF
1 Row
Y/M/D
24 HR
Date First
User’s Manual
15
3.4.1 Set Date / Time
Set Date / Time
Select <Date> / <Time> and press ENTER for adjusting the settings. LEFT /
RIGHT keys are used to move the cursor to previous or next field, ENTER is
for selecting, and UP / DOWN are used to change the value in the selected
field.
NOTE: The new date / time setting applies to record new video. The
date and time of previously recorded video will not be changed.
NOTE: If you have to change time settings in any case, we strongly
recommend you to format the HDDs to avoid database corruption.
Date / Time Display
Users are allowed to set the time OSD displays in 1 or 2 rows. Use the UP /
DOWN keys to change the setting. The default is to display the time OSD in
one row.
Date Display Mode
This function allows user to set the OSD display type of the date. There are
three options to select from: <Y/M/D>, <M/D/Y> or <D/M/Y>. “Y” represents
“Year”, “M” represents “Month” and “D” represents “Day”.
Move to the item and press ENTER, the option starts blinking. Use UP /
DOWN keys to change the setting. The default setting is <Y/M/D> in both
NTSC / PAL formats.
Time Display Mode
User can set the time format to <12 hour> or <24 hour>. Use the UP / DOWN
keys to change the format. The default setting is <12 hour>.
Date / Time Order
The item is used to set the order of date / time display to <Date First> or
<Time First>. Use UP / DOWN keys to change the setting.
User’s Manual
16
3.4.2 Daylight Saving Time
Daylight Saving Time
The item is for those people who live in certain regions to observe Daylight
Saving Time. Select <ON> to enable, or <OFF> to disable the function.
If the function is disabled, the DST Start / End time and DST Bias will be
grayed out and cannot be accessed.
NOTE: If this function is enabled, the date/time information will be
shown on the screen with a DST icon when playing back recorded
video or searching video in the event list. “S” indicates summer time
and “W” indicates wintertime.
DST Start / End
The items are used to program the daylight saving duration. Use LEFT /
RIGHT keys to move the cursor to the next or previous field, UP / DOWN to
change the settings in the selected field.
DST Bias
The item allows user to set the amount of time to move forward from the
standard time for daylight saving time. The available options are <30>, <60>,
<90> and <120> minutes.
User’s Manual
17
3.4.3 Network Time Protocol Setup
Time Zone
Select <Time Zone> to enter the time zone. To find out your local time zone,
please visit www.greenwichmeantime.com or refer to the following figure.
NOTE: The <Time Zone> must be set to your local time zone or the
<Network Time Protocol Setup> will not be accessible.
Network Time Protocol Setup
After entering the time zone, the <Network Time Protocol Setup> option will
appear. Select the <Network Time Protocol Setup> to set the time server.
The default time server is time.nist.gov, but the user can change it to other
time servers when desired. A list of IP addresses of the time servers is listed
below.
129.6.15.28 129.6.15.29 132.163.4.101
132.163.4.102 132.163.4.103 128.138.140.44
192.43.244.18 131.107.1.10 69.25.96.13
206.246.118.250 208.184.49.9 64.125.78.85
207.200.81.113 64.236.96.53 68.216.79.113
After the time server is set, select <Manually Time Sync> to sync the time.
The time sync can also be updated periodically. Select <Automatically Time
Sync>, and the time will be automatically synced once an hour.
User’s Manual
18
3.5 Record Schedule / Quality Setting
The Record Setup menu allows user to set recording quality, recording
schedules, and other recording parameters. Administrator's password is
required to access Record Setup menu. In the Main menu, move the cursor
to <Record Setup> and press ENTER; the following menu is displayed.
Record Setup
1. Record Mode
2. Schedule Setup
3. Preset Config
4. ezRecord Setup
5. Circular Recording
6. Purge Data
720×240@60PPS
Standard
ON
3.5.1 Schedule Setup
The Schedule Setup is used to set the day and night time, or weekend
recording schedule. Select <Schedule Setup> from the Record Setup menu
and press ENTER; the following menu is displayed.
Schedule Setup
1. Day Time Start
2. Day Time End
3. Night Time Start
4. Night Time End
5. Weekend Schedule
6. Weekend Start
7. Weekend End
AM 06:00
PM 06:00
PM 06:00
AM 06:00
YES
Fri 18:00
Mon
06:00
• Make appropriate changes of the start time of Day and Night Time using
Direction keys.
• Press ENTER to confirm the settings or ESC to cancel.
• If you want to have a weekend record, choose <YES> to enable the
Weekend Schedule in advance and then set the Weekend Start/End time.
• Press ESC to return to previous page.
User’s Manual
19
3.5.2 Preset Record Configuration
The <Preset Config> is used to select the preset recording quality and frame
rate. In normal circumstances, we strongly suggest you set the item to
<Standard>, the default. Below table shows the PPS and picture size under
<Standard> in Half-D1 mode. Please refer to OSD Menu Setup Guide,
Section Preset Record Configuration for more detailed information.
Halfl-D1 mode (NTSC: 720x240@60PPS; PAL: 720x288@50PPS)
Normal PPS Normal Size Event PPS Event Size
3.75 NTSC
(3.125 PAL)
11 KB
15 NTSC
(12.5 PAL)
17 KB
3.5.3 To Record Event Video Only
If you want your DVR unit to start recording only when the alarm is triggered,
follow the steps:
• Enter the OSD setup menu with correct password.
• In the OSD setup menu, select <Record Setup> menu. Move the cursor to
the item <Preset Config>, and select <Event only>.
Refer to OSD Menu Setup Guide, Section Preset Record Configuration for
more detailed information.
3.5.4 ezRecord Setup
This item aims to ease the complicated record settings, and to make the
setup much easier. Note that the item can be reached only when you select
<ezRecord> as the option for <Preset Config>.
Select <ezRecord Setup> from <Record Setup> and press ENTER, the
sub-menu appears as below figure:
ezRecord Setup
How Many Days To Record
Daytime Record
Night Record
Weekend Record
Average Normal PPS
Average Normal Quality
2 Days
Yes
Yes
Yes
3.75
Best
Record Info
User’s Manual
20
Follow these steps to Setup ezRecord:
• Select <How Many Days To Record> and press ENTER, then press
UP/DOWN to choose an option. The average normal PPS & Quality will
be adjusted automatically. The maximum of days depends of the size of
your HDD. In other words, the larger the size of the HDD installed, the
more days the unit can record.
• Move to <Daytime Record> and press ENTER. This item is for you to
select whether you want the DVR to record during daytime. If yes, use
UP/DOWN to select <Yes> as to enable day time recording; or select
<No> to disable.
• Repeat the same procedures through the 3rd and 4th item, respectively.
Note that <Weekend Record> will be inaccessible if you select <NO> for
the item <Weekend Schedule> in <Schedule Setup>.
• Select <Average Normal PPS> and press ENTER, then press
UP/DOWN to make a choice. The <How Many Days To Record> will be
computed automatically.
• Select <Average Normal Quality> and press ENTER, then press
UP/DOWN to make a choice. The <How Many Days To Record> will be
computed automatically.
NOTE: The current number of connected cameras will affect
the recording quality automatically calculated through the
<ezRecord Setup>. Therefore, once you disconnect cameras or
connect more cameras to the unit, you should reset the
<ezRecord Setup>.
3.5.5 Circular Recording
User can choose to record video in circular mode or in linear mode. If you
choose to record in circular mode, then the unit begins to stores new video
into the HDD spaces and overwrite the oldest recorded video. If you choose
to record in linear mode in stead, the unit stops recording when the HDD is
full, and the internal buzzer starts beeping.
From the Record Setup menu, move the cursor to <Circular Recording> and
press ENTER, then select <ON> / <OFF> using UP / DOWN keys.
User’s Manual
21
3.5.6 Purge Data
This item is used to delete the Normal or Event recording video. In Record
Setup menu, move the cursor to <Purge Data> and press ENTER; the Purge
Data menu is displayed.
Purge Data
1. Purge All Data
2. Purge All Event Data
3. Purge Event Before
4. Start to Purge
NO
NO
2005/01/01
NO
• Purge All Data
The item is used to delete all recorded video from database(s). Set this item
to <YES> using UP / DOWN keys, and start the deleting by enable (YES) the
<Start to Purge> function.
• Purge All Event Data
The item is used to delete all event video from database(s). Using UP /
DOWN keys to select <YES> and start the deleting by setting the <Start to
Purge> to <YES>.
• Purge Event Before
The item is used to delete event video before a specific date. Use LEFT /
RIGHT keys to move the cursor to next or previous field, ENTER to select the
item and UP / DOWN to adjust the value.
• Start to Purge
After selecting the video you want to delete or setting the date for deletion,
set this item to <YES> for start the deleting or choose <NO> to cancel.
User’s Manual
22
4. Basic Operation
The DVR series unit allows user to access some general operations through
the front panel easily. The following sections introduce the general operations
of the unit.
4.1 Viewing Live / Playback Video
The general functions in live and playback mode are described in the
following sections.
4.1.1 Viewing Modes
The DVR series unit provides user versatile ways of viewing both live and
recorded video. Following presents these view formats.
Viewing in Full Screen
Press any CHANNEL key directly to view the corresponding camera image in
full screen format.
Viewing in Multi-window
Various multi-window view formats are offered for selection. To switch
between available viewing formats, press MODE repeatedly.
The available view formats are illustrated as the following figure.
User’s Manual
23
4.1.2 Digital Zoom
Users are able to view a 2× full screen in live mode. To view the 2× full
screen, follow the steps.
• Press a CHANNEL key to view the corresponding camera in full screen.
• Press ZOOM to enter a 2× full screen zoom mode of the selected camera.
• If you need to view specific area of the 2× zoomed screen, use Direction
keys to pan / tilt the zoomed area around the original image.
• Either press ZOOM again or ESC to leave the zoom mode.
4.1.3 Viewing Live Cameras
Users are allowed to view live camera in versatile viewing modes, including
full-screen, 2×2, 3x3 and 4×4. The general operation under live mode is
described as follows.
To Freeze Live Image
Press FREEZE while viewing live image, the image pauses but the date /
time information does not, and the system clock continues running.
Press FREEZE to pause the live image; press FREEZE again to resume the
live camera view.
4.1.4 Viewing Recorded Video
To view recorded video, user can press PLAY/STOP key directly. When press
the PLAY/STOP key, the unit starts to continue playing back the recorded
video from the suspended point of record. If it is the first time to use the
PLAY/STOP key, the unit will playback from the very beginning of the record.
Alternatively, user can select records from the Search menu to play specific
video. Refer to OSD Menu Setup Guide, Section Searching Recorded
Video for more information.
The Forward or Reverse speed indicator will be shown on the bottom-left of
the screen, when in the playback mode.
The general operations in playback mode are described as follows.
User’s Manual
24
Key Usage in Playback
The key usage is slightly different in playback mode. Following is the key
usage found in playback mode.
z LEFT (Reverse Playback)
The key is used to reverse the recorded video while the unit is playing
back. Press the key repeatedly to increase the speed of reverse
playback by 1×, 2×, 4×, 8×, 16×, or 32×.
z RIGHT (Forward Playback)
The key is used to play the recorded video fast forward. Press the key
repeatedly to increase the speed of forward playback by 1×, 2×, 4×, 8×,
16×, or 32×.
z FREEZE
Press FREEZE to pause the playback video. When the recorded video is
paused, press LEFT / RIGHT to resume playback video single step
reverse / forward, respectively. Press FREEZE again to continue playing
video.
z PLAY/STOP
Press it to start playing back video, exit current mode, or stop playing
back video and return to live mode.
Pause Playback and Single Step Forward
To pause and resume recorded video, follow these steps.
• Press one of the CHANNEL keys to display the corresponding camera in
full screen.
• Press FREEZE to pause the current playback image.
• Press RIGHT / LEFT Direction keys to move the video single step reverse
/ forward. Press and hold RIGHT / LEFT keys to repeatedly reverse /
forward the video single step.
• Press FREEZE again to resume the playback operation.
User’s Manual
25
Viewing Live Image in Playback Mode
Press the MODE key repeatedly in playback mode, a 16-window viewing
mode contains both live and playback image appears. This viewing mode is
illustrated as the following figure.
The eight windows on the top side of the screen playback the Live video from
channel 1 to channel 8 respectively, and the other windows allow user to view
Playback image from channel 1 to channel 8.
4.2 Sequence Setup
This section introduces the way to view sequence mode with both Main
Monitor and Call Monitor, if connected. Sequence function can avoid manual
backtracking and provides more flexibility while monitoring surveillance.
4.2.1 Sequence with Main Monitor
Automatic sequence function can be observed in any view mode. Select
certain view format and press SEQ to toggle the automatic sequence; press
ESC to stop sequencing. The figure below displays the 4-camera and
9-camera sequencing view modes.
User’s Manual
26
4.2.2 Sequence with Call Monitor (8ch and 16ch only)
Users are allowed to use the DVR series unit front panel to control a call
monitor display without having to access the Main menu. Two viewing modes
can be displayed on call monitor: Sequence display and Single camera
display. To program the call monitor sequence, see OSD Menu Setup Guide,
Section Sequence Setup.
Follow the steps to control the call monitor.
• Press the CALL key on the front panel to enter call monitor control mode.
The message “Call Mode” will be shown on the bottom-left of the screen.
Press 1-16 Key To Select Channel
Press SEQ To Enable Sequence
Call Mode
• Press CHANNEL key to display the associated camera on call monitor.
• Alternatively, press SEQ repeatedly to display the sequence of cameras
previously programmed in Call Monitor Schedule menu.
• Press ESC to return the front panel to Main monitor control mode.
4.3 Searching Recorded Video
The DVR series is capable of searching and playing back recorded video by
date and time or events. Entering the specific date and time of the wanted
video, the unit will then search for the matched video and play it on the
monitor. Alternatively, the user can search event video by selecting channel
as well.
In live or playback mode, press SEARCH to enter the Search menu, which is
shown as follows.
Search
----------------------------Search By Time---------------------------From:
End:
Select:
2005/01/01 00:00:00
2005/05/01 00:00:00
2005/01/01 00:00:00
Begin Playback
----------------------------Search By Event---------------------------Select Channel: CH1 CH2 CH3 CH4
Event List
User’s Manual
27
4.3.1 Searching by Time
Follow the steps to search video by date and time.
• Press SEARCH key to enter the Search menu; the From Time and End
Time of the available video is listed on top of the screen. The value is
unchangeable.
• Use Direction keys to move the cursor for setting the start time; adjusting
the date and time values by UP / DOWN keys.
• Press ENTER to confirm the settings or ESC to abort.
• Move the cursor to <Begin Playback> and press ENTER to start playing
back the selected video.
• Either press PLAY/STOP again or ESC to return to live video.
NOTE: If there is no available recorded video that matches your
specified time and date, the unit starts playback from the next
available video.
NOTE: The date/time information will be shown on the screen
with a DST icon if the Daylight Saving Time function is enabled.
“S” indicates summer time and “W” indicates winter time.
4.3.2 Searching by Event
“Event List” allows you to search wanted video by event. The Event List is
displayed as below figure:
Event List
First Page
Date Time
2005/03/17 11:26:50
2005/03/17 09:53:03
2005/03/16 16:14:42
2005/03/15 03:45:31
2005/03/12 22:27:56
2005/03/12 10:09:29
2005/03/11 12:18:20
2005/03/10 05:16:00
2005/03/08 17:11:37
2005/03/08 16:29:10
2005/03/08 03:22:17
Ch.
2
5
3
1
1
7
6
4
2
8
2
Type
Motion
Alarm
Alarm
Motion
Alarm
Motion
Motion
Alarm
Motion
Motion
Alarm
User’s Manual
28
The list displays events by date, time, triggered camera and alarm type. As
some events are deleted, others are displayed. The latest recorded event
video will be listed on the top.
Follow these steps to search event video through Event List:
• Press SEARCH to enter the Search menu.
• To search event video that has been recorded on a specific camera, use
LEFT / RIGHT to move the cursor and press ENTER to select or de-select
a channel.
• Move the cursor to <Event List> and press ENTER to list the event video
of the selected channels. The Event List displays.
• To exit the event list, press ESC.
Follow the steps to playback video from Event List.
• Press and hold UP / DOWN to scroll through the Event List.
• Press ENTER to play back the selected event record.
• Press PLAY/STOP to return to live mode.
4.4 Video Export
The unit allows you to export wanted video to the built-in CD-RW or an
external device, such as a USB ThumbDrive®, and the exported video will be
saved as *.drv file.
If you want to export video to an external device, make sure the device is has
been connected to the DVR unit and the port has been set appropriately for
video export.
NOTE: Once an external device has been connected to the DVR unit,
the device has priority over the built-in CD-RW; which means that the
wanted video will be exported to the external device instead of the
built-in CD-RW.
According to the size of video, the export may take about 10 minutes to 1
hour.
User’s Manual
29
4.4.1 ezBurn Introduction
Built with the ezBurn technology, ezBurn function provides users the easier
way to export desired video with built-in CD-RW or to an external device,
such as an USB ThumbDrive®.
TWO keys (SEARCH and COPY) and THREE touches are all you need for
completing the export. The entire exporting process will be done through the
front panel, without needing to enter the OSD setup menu.
The ezBurn exporting process is illustrated as below figure:
The entire process is described step by step in the following sections.
NOTE: The file exported using ezBurn will be in .drv file format, and
it can only be played using the remote player software.
4.4.2 To Export Normal Video
To Export normal video to external device, follow these step:
• Press SEARCH and play wanted normal video by entering date and time.
Note if you are viewing in multiple channel mode, please make sure there
is no window displaying in Live mode. Otherwise, the export won’t work.
• After entering playback mode, play the video and press COPY at the point
that you want to start the export. The playback continues.
• Press COPY again at the point that you want to end the export. Then the
“ezBurn” window will display as below figure. The information shown on
the window is read only.
ezBurn confirmation
Selected Device: Built-in CD-RW
All data on the disc will be erased.
Exported Required Size = 11 MB
Real Export Range:
From: 2005/11/07 AM10:41:13
To: 2005/11/07 AM10:41:21
Enter: YES ESC: NO
User’s Manual
30
• Press ENTER to start the export; or, press ESC to abort.
• If there is no any exportable device connected to the DVR unit, then a
warning message will be shown on the screen, as below figure:
No exportable device detected.
Please install the target device/media
to the DVR.
Enter: Retry ESC: Exit
4.4.3 To Export Event Video
To export event video, follow these steps:
• Press SEARCH and play wanted event video. To play event video, refer to
Section Searching Recorded Video.
• After entering the playback mode, press COPY. The “ezBurn” window will
display as below figure. The information shown on it is for read only.
ezBurn confirmation
Selected Device: Built-in-CD-RW
All data on the disc will be erased.
Exported Required Size = 11 MB
Export Event Info:
Data Time Ch Type
205/11/07 AM10:42:35 13 Motion
Enter: YES ESC: NO
• If there is no any exportable device connected to the DVR unit, a warning
message will be shown on the screen
• Press ENTER to start the export the whole event video to the connected
device; or, press ESC to abort.
4.5 Dome Control
The DVR series unit allows user to control a dome camera by the front panel.
In Live mode, user can press CHANNEL key to display the desired dome
camera in full screen. To enter Dome Control mode, press the DOME key and
press channel key 2 to display the hint screen; to exit the Dome Control mode
and return to live mode, press ESC or DOME.
User’s Manual
31
To configure the dome controls settings, see the following sections.
4.5.1 Dome Connection
Follow the steps to install dome camera.
• See Setup Guide for RS-485 port pin definition.
• Connect the R+, R- terminals on the dome camera to the D+, D- terminals
on the RS-485 port by RS-485 cable respectively. Refer to the connection
figure illustrated in Setup Guide.
4.5.2 Dome Protocol Setup
The Dome Protocol item lists the available dome protocols for communicating
with dome cameras connected to the DVR series unit. From the Main menu,
select <Camera Setup> and press ENTER. The following menu is displayed.
Analog Camera
1. Analog Camera Select
2. Dome Protocol
3. Dome ID
4. Camera Title
5. Covert
6. Brightness
7. Contrast
8. Saturation
9. Hue
CH1
None
0
NO
0
0
0
0
To configure dome protocol, select a camera first and set the communications
protocol associated with dome camera using the Direction keys and ENTER.
The available protocol includes <DynaColor>, <Pelco D>, <Pelco P>,
<AD422>, <Fastrax 2>, <JVC>, <Panasonic_C>, <Panasonic_N>, and
<None> (default).
NOTE: The settings become effective after saving the changes and
exiting from the menu.
User’s Manual
32
4.5.3 RS485 Setup
The DVR series unit controls the domes via RS-485 communication protocol.
The RS-485 parameters in the DVR series unit must be set to the same
parameters set in dome camera.
Users are allowed to change the RS-485 settings of the DVR series unit.
Select <System Setup> in Main menu, then select <RS485 Setup> from the
System Setup menu and press ENTER. The following menu is displayed.
RS485 Setup
1 Unit ID
2 Baud Rate
3 Bits
4 Stop
5 Parity
224
9600
8
1
None
The ID number must match the ID address set by the dome. The Unit ID is in
the range of 1 to 255. The default ID is 224. Note that there cannot be any
two devices on the same bus given the same ID address, or a conflict may
occur.
The default RS-485 settings of the DVR series unit are 9600 Baud, 8 Data
Bits, 1 Stop Bit and No Parity.
NOTE: The settings become effective after saving the changes and
exiting from the menu.
4.5.4 Dome Controlling Keys
The functions of some keys in dome control mode are totally different from
normal status function. Please refer to Setup Guide for the graphical
illustration of functional keys.
Set / Go Preset
This key is used to enter the Dome Preset menu to set up certain position as
a preset and go to the predetermined preset positions for viewing.
Toggle Hint Screen
This function is used to avoid viewing the dome parameter information while
controlling dome camera. Press this key to hide the screen. Press it again to
redisplay the screen.
User’s Manual
33
Iris Open
Use to open the Iris on the dome camera.
Focus Near
Use to focus the dome camera near.
Zoom In
Use to zoom in the dome camera. This function enables the user to enlarge a
certain area.
ESC
Use to leave dome control mode and return to live and full screen viewing
mode.
Auto / Enter
• In OSD Menu mode, the key is used to make selection.
• In dome control mode, this key is used to activate automatic focus and iris
function.
Iris Close
Use to close the Iris on the dome camera.
Focus Far
Use to focus the selected dome camera far.
Zoom Out
Use to zoom out the dome camera. This function enables the user to shrink
the current image and view a larger area.
Pan / Tilt
Use to pan and tilt dome camera.
User’s Manual
34
4.5.5 Setting Preset Points
The DVR series unit allows user to set preset positions. The amount of preset
points depends on the dome manufacturer.
Follow the steps to set preset points.
• Press a Channel key to view the corresponding camera in full screen.
• Then press DOME to enter dome control mode. And a Hint Screen shown
as below figure displays on the screen.
• Press 2 to hide the dome control Hint Screen; press 2 again to toggle the
Hint Screen.
• Use Direction keys to position the dome camera to desired position.
Hint Screen
DOME / ESC: Exit
MODE / PLAY: Iris Open / Close
SEQ / FREEZE: Focus Near / Far
MENU / SEARCH: Zoom In / Out
ENTER: Auto Focus / Iris
◄▲▼►: Pan / Tilt
CH1: Set / Go Preset
CH2: Hint Screen On / Off
Dome Control
• Press 1 to access the Set/Go Preset function. The Dome Preset menu is
displayed.
Dome Preset
Index
1
2
3
4
5
6
7
Set Preset
NO
NO
NO
NO
NO
NO
NO
Go Preset
NO
NO
NO
NO
NO
NO
NO
• Use UP / DOWN keys to select the desired preset number from the menu.
• Set the <Set Preset> of the selected preset number to <YES>, and press
ENTER to save the position. Now the preset is set and ready to be called.
User’s Manual
35
4.5.6 Calling Preset Points
Follow the steps to call preset points.
• Press a Channel key to view the corresponding camera in full screen.
• Then press DOME to enter dome control mode. Then a Hint Screen,
shown as blow figure, will display on the screen.
• Press 2 to hide the dome control Hint Screen; press 2 again to toggle the
Hint Screen.
• Press 1 to access the Set/Go Preset function.
Dome Preset
Index
1
2
3
4
5
6
7
Set Preset
NO
NO
NO
NO
NO
NO
NO
Go Preset
NO
NO
NO
NO
NO
NO
NO
• Use UP / DOWN keys to select the desired preset number from the menu.
• Set the <Go Preset> of the selected preset number to <YES>, and press
ENTER to call the preset point.
• Now the selected dome camera rotates to the preset position automatically.
User’s Manual
36
5. Remote Monitoring Software
The remote monitoring software is a remote browser-based software
application designed to operate with the DVR series products. Using the
software, users are allowed to view live and recorded video, and also to
configure the DVR series units remotely via a LAN, WAN or Internet on your
personal computer.
The DVR series unit automatically downloads the remote monitoring software
plug-ins to the connected PC when you connect to the DVR series unit by
entering the IP address of the unit in the address bar on the browser.
Due to the setting items are similar to those listed in the DVR’s OSD setup
menu, please refer to the sections above for setting configuration of the
remote monitoring software.
The tasks can be performed with the remote monitoring software are listed
below:
• Remote viewing of live/ recorded video
• Remote setup of the DVR series unit
• Remote control of dome cameras
• Alarm notification from the DVR series unit
• Up to five connections to one DVR series using the remote monitoring
software, including one Administrator and four User operators
5.1 Remote Monitoring System Requirements
Items Minimum Requirements
Personal Computer
Pentium-3 600 MHz processor (Pentium Celeron or
Pentium-4 1.5GHz processor preferred)
Minimum RAM 256 MB
Hard Drive 20 MB available for software installation
Operating System
Windows XP, 2003
Windows 2000
Web Browser
Microsoft Internet Explorer version 6.0 or above
Monitor Resolution
Minimum 1024 x 768 with 16-bit color
Video Card
XVGA with 16 MB video RAM
Network Card
10Base-T (10 Mbps) or 100Base-TX (100 Mbps)
operation; must match the network configuration
User’s Manual
37
5.2 Getting Start of Installation
Refer to the following description to install the remote control software.
5.2.1 Changing Internet Settings
The PC you want to operate with the remote monitoring software should be
set to accept ActiveX plug-ins. Please follow the steps to set the Internet
security settings appropriately.
• Before operating the remote monitoring software, please check the IP
address of your DVR series unit. To check the IP address, press MENU
key on the unit and enter password to access OSD setup menu. Select
<System Setup>, <Network Setup>, then <LAN Setup> to check the IP.
• Start the IE; you may start it either by clicking on the desktop icon, or by
using the Start menu to access it.
NOTE: Windows IE provides the ActiveX component that is
required when using the remote monitoring software.
• Select <Tools> from the main menu of the browser, then <Internet
Options>, and then click the <Security> tab.
• Select <Trusted sites> and click <Sites> to specify its security setting.
User’s Manual
38
• Uncheck “Require server verification (https:) for all sites in this zone”.
Type the IP address of the unit in field and click <Add> to add this web site
to the zone.
• Click <OK> to confirm the setting and close Trusted sites dialog.
• In the Security Level area, click <Custom Level>. The Security Settings
screen is displayed.
• Under <All ActiveX controls and plug-ins>, set all items to <Enable> or
<Prompt>.
• Click <OK> to apply the setting and close the <Security Settings> screen.
• Click <OK> to close Internet Options dialog.
Now you can continue with the rest of the installation.
User’s Manual
39
5.2.2 Installing Remote Monitoring Software
Start the browser to initiate the installation of the remote monitoring software
on your personal computer. You can save the IP address of the remote unit
as a Favorites item in your web browser to have easy access next time.
• Start the IE; you may start it either by clicking on the desktop icon, or by
using the Start menu to access it.
• Enter the IP address of your DVR series unit in the address bar at the top
of the browser.
• The ActiveX controls and plug-ins dialog will show twice for confirmation;
click <YES> to accept ActiveX plug-ins. The remote monitoring software
plug-ins will be downloaded and installed on your PC automatically when
the connection is successfully made.
NOTE: Do not enter any leading 0 characters in the address, for
example, “192.068.080.006” should be entered as “192.68.80.6”.
If the default trigger port 80 is changed into another one, take port
81 for example, you should enter the IP address as
“192.68.80.6:81”.
• A version check starts to verify whether the remote monitoring software
was installed already, and also check if the version is the same as that
stored in that particular DVR series unit. This process may take up to 30
seconds.
• When the software is completely downloaded and installed, the Login
Screen is now displayed.
User’s Manual
40
5.2.2.1 Log in / Log off
You can log in using the <Admin> or <User> account. <Admin> account can
perform unit configuration freely, while <User> account has more limitation on
remote access to the unit.
One “Admin” and up to four “Users” can access a DVR series unit at the
same time. Furthermore, if the “Admin” account is currently accessing the
unit’s OSD setup menu via front panel of the unit, then you cannot save
information as an “Admin” on the remote monitoring software. The Admin
account of the DVR series unit has priority.
The following steps demonstrate procedures to view video from remote unit:
• Start the remote monitoring software by entering the IP Address of the
DVR series unit in the Address bar of the browser. Or you may click on the
Favorite entry for the unit (if the IP address of the unit has been set).
• Enter your Username and password. You can save password in the list if
needed. The default usernames and passwords are listed as below.
Login Type
Default User name
Admin User
Default Password
1234 4321
• Click <OK> to log in to the DVR series unit. The process may take a few
seconds.
• If the connection is made successfully, the main window will display live
video of the attached cameras.
If you close the IE browser, you log off the system at the same time.
User’s Manual
41
5.2.2.2 Software Upgrades
When a new version of the remote monitoring software is available on your
DVR series unit, upgrade will be prompted when you access the unit. Follow
the steps to upgrade the software.
• The message as the above figure will be prompted. Click <Yes> to accept
version upgrade.
• Start your IE again and enter the IP address of the DVR series unit in the
Address bar of the browser; or if you have set a Favorite for the unit
address, click the Favorites entry for your unit.
• When the software is completely downloaded and installed, the Login
Screen will be displayed.
5.3 Basic Operation for Monitoring remotely
When you successfully connect to a DVR series unit, the main window of the
remote monitoring software will display as follows. The connected cameras of
the DVR series unit will be listed on the left and an array of camera output
windows will display on the right of the main window.
User’s Manual
42
To view the main window in full-screen view, press <F11> on your keyboard.
The functions on the remote monitoring software will be described in the
following sections.
5.3.1 To View Live Video
You can view live video from the cameras attached to the DVR series unit by
clicking <Live> button on the main window toolbar.
You can select desired display mode and assign wanted camera view to the
window(s) after the live images of the DVR series unit are displayed on the
main window. To select wanted display mode and assign camera, refer to the
following sections.
5.3.1.1 Selecting Display Mode
You can choose the number of windows to be displayed on
the main window. Click one of the display buttons on the
left-bottom corner of the main window. You can select from 4,
9 and 16 camera displays. To view certain window in full
screen, you may either double-click on the wanted window,
or click on the corresponding CAMERA button.
User’s Manual
43
5.3.1.2 Operating Cameras with Dome Control
The remote monitoring software allows you to control and
configure a dome camera remotely.
Click on any CAMERA button displayed with a dome icon to
view the camera in full screen. The Dome Control Panel
(shown as right) will be displayed in the left-bottom side of
the main window. The items on the dome control panel are
described as follows.
Set Preset Points
This item is used to set up preset positions.
The remote monitoring software allows its user to set up to 255 preset
positions with DynaColor, American Dynamics, Fastrax, JVC, Panasonic (C &
N), and Pelco (Pelco P & Pelco D) domes.
Use Direction buttons to move dome camera to an appropriate position, and
then click the button and choose wanted number from the pull-down list. The
preset position is named as the selected number.
Go Preset Point
This item is used to call the camera preset point which was set up with
the set preset point function. Click and choose a number to call the preset
point for viewing.
A.F. (Auto Focus)
Click to automatically adjust the focus of the camera for a clear view.
ID (Dome ID Setup)
Click for changing the dome ID and protocol. User
privileges in not allowed to change the dome ID and
protocol; Admin privileges is required to access this
function.
Focus
Use to adjust the camera lens to focus on objects for a clear view. Click the
adjusting buttons to modify the focus setting.
User’s Manual
44
Iris
This item is used to open and close the iris to let more or less light into the
camera. Click the adjusting buttons to modify the iris setting.
Zoom
You are allowed to zoom-in or zoom-out using the adjusting buttons. Zoom-in
to enlarge a certain area and zoom-out to view more area.
Direction Buttons
These buttons are used to pan and/or tilt the dome camera. Click the arrow
button in the direction you want to view.
5.3.2 Instant Recording
The Instant Recording function allows you to record video
quickly to your PC.
NOTE: The Audio function is set to OFF as the
default setting.
5.3.2.1 Recording Video Instantly
Follow the steps to start recording instantly:
• Click on the <Instant Recording> button.
• Select the destination you want to save the video.
• Click on the button again to stop recording.
NOTE: The instant recording video will be saved as *.drv file.
5.3.2.2 To Playback Instant Recorded Video
Follow the steps to playback a video recorded by “Instant Recording”.
• Click <Play> on main window toolbar and click <Local Playback> tab.
• Click <Open> to choose a recorded file.
• Click <OK> to start playing the recorded video.
5.3.3 To Take a Snapshot
The software allows you to take a snapshot through the hot key on the top of
the main window. Each click takes a snapshot and it will be saved as a *.BMP
file on the desktop of you PC. The snapshot file will be named as
“Snapshot-*”.
User’s Manual
45
5.3.4 To Playback Video
The remote monitoring software allows you to view recorded video either
from the DVR series unit, or playback from the hard disk drive of your PC
To access the Playback screen, click <Play> button on the main window
toolbar. There are three tabs in the Playback screen: <Remote Playback>
and <Local Playback> tabs. <Remote Playback> allows you to play back
from a DVR series unit. <Local Playback> enables you to playback a
recorded video file stored on the hard disk drive of your PC.
The DVR series unit continues recording while you are playing back recorded
video on your PC, either remote playback or local playback.
5.3.4.1 Playing Back Remote Video
To view remote video, click <Play> on the main window toolbar, and then
<Remote Playback> tab. The <Remote Playback> screen will be displayed.
The <From> and <To> in the <Available Record Video> on top of the screen
display the date and time from which recorded video is available for playback.
To playback remote video segments, follow these steps:
• Choose <Playback> in <Select> field for playback recorded video.
• Select the date and time of the segment to playback from the <Start> field.
User’s Manual
46
• You can change the date and time either by typing desired numbers
directly or using the arrow buttons.
To type directly:
Click on day, month and year of date field respectively, and type the
desired numbers directly. Follow above steps to adjust the hour, minute
and second of time field.
To use the arrow buttons:
Click on the arrow button next to the date field to display the calendar; then
click the left and right arrow at the top of the calendar to change the date.
Use up and down arrow next to the time field to change to the wanted time.
• The other way to select date and time is by moving the blue sliding bar in
the center of the screen.
• Click <OK> to start the playback, or click <Close> to abort.
• The other option <Download (.DRV)> in <Select> field enables the user to
download the video segment of selected date and time to the PC. The
selection of time duration is the same as described above. Files
downloaded will be in *.drv format.
5.3.4.2 To Playback Local *.drv Files
The <Local Playback> tab allows you to playback *.drv video files stored in
your PC's hard drive.
Click the <Local Playback> tab in the <Playback> screen. The Local
Playback screen is shown as below.
User’s Manual
47
Follow below steps to play back a downloaded *.drv file with the remote
monitoring software.
• Click <Open> and the file selection screen is displayed.
• Select the *.drv video file to playback and click <OK>.
• Click <OK> in the <Local Playback> Screen to start the playback, or click
<Cancel> to abort.
• View the video playback using the Playback controls.
• To end the playback, click <Live> to return to live video.
5.3.4.3 Playback Controls
When playing back local or remote video, the remote monitoring software is
in Playback Mode. The playback controls toolbar will emerge on the main
window toolbar, as shown in the following figure.
The Playback controls and indicators are described as below.
Fast Backward
Click to play the recorded video in reverse direction. Click repeatedly to
select the rewind speed: 1×, 2×, 4×, 8×, 16×, or 32×.
Play / Pause
Click once to play the recorded video; click again to pause the playback.
Fast Forward
Click to play the recorded video forward. Click repeatedly to select the
forward speed: 1×, 2×, 4×, 8×, 16×, or 32×.
User’s Manual
48
5.3.5 Search from Event List
Click SEARCH, the Event List appears. The List contains information about
the alarm events that your unit recorded and saved. Up to 1024 events can
be listed in the Event List.
The Event List (shown as below figure) displays each event by its number,
the date and time of the event, the type of the event (including Alarm In,
Motion Detection, Video Loss, and Over Speed), and the camera channel
where the event occurred.
To view an event video, follow these steps:
• Click SEARCH button positioned in the main window toolbar. The Event
List appears.
• Scroll through the Event List and highlight the interested events.
• Double-click on the desired event to view the event video.
User’s Manual
49
5.3.6 Remote Monitoring Software Trouble Shooting Guide
What if the server ask to upgrade the software every time when you try to
connect to the DVR series unit unit? If the following screen displays
repeatedly, please follow the steps to delete the temporary internet files.
• Select <Tools> from the main menu of the web browser, then <Internet
Options>, and then click the <General> tab.
• Click the <Delete Files> button in the <Temporary Internet Files> field; the
<Delete Files> screen displays as below.
• Check the <Delete all offline content> box and click <OK>.
• Now, enter the IP address of your DVR series unit to make the connection
again.
User’s Manual
50
Appendix A: Technical Specifications
RN684 RN688 RN6816
PAL/CCIR: 625 lines, 25 frames per second
NTSC/EIA: 525 lines, 30 frames per second
INPUT STANDARD
Composite video, 1Vp-p, BNC, switchable
INPUT CHANNELS 4 8 16
Main Monitor BNCx1, 1.0Vp-p, 75 ohm
Call Monitor - BNCx1, 1.0Vp-p, 75 ohm
OUTPUT
STANDARD
VGA (Optional) 800x600, 1024x768, 1280x1024 pixels
COMMUNICATION NETWORK TCP/IP, DHCP, DDNS
CONCURRENT USERS 2
RECORDING MODE Schedule / Motion / Alarm / Remote
D1 (PAL: 720x576 / NTSC: 720x480)
Half D1 (PAL: 720x288 / NTSC: 720x240)
RECORDING RESOLUTION
CIF (PAL: 368X288 / NTSC: 360X240)
HD TYPE IDE interface, ATA66, 2 internal
COMPRESSION FORMAT MPEG-4, Advanced Simple Profile
PAL: 25fps (720X576); 100fps (360X288)
MAX RECORDING RATE
NTSC: 30fps (720X480); 120fps (360X240)
PLAYBACK SCHEDULE Date, time, event
PLAYBACK SPEED 1X, 2X, 4X, 8X, 16X, 32X
ALARM IN/OUT
4 inputs,
1 output
8 inputs,
1 output
16 inputs,
1 output
AUDIO IN/OUT 2 inputs, 2 outputs
BACKUP DEVICE CD-RW, USB
TELEMETRY STANDARD RS-485, 1200, 2400, 4800, 9600, 19200bps
TELEMETRY PROTOCOL
Pelco P, Pelco D, AD422, Fastrax 2,
JVC, Panasonic_C, Panasonic_N
OPTIONAL PERIPHERAL VGA converter
VOLTAGE External Adapter, AC 100~240V to DC 12V
MAX. RATING 96W
AMBIENT TEMPERATURE 0°C ~ 40°C
RELATIVE HUMIDITY 30% ~ 90% (no condensation)
DIMENSION 440mm (W) x 50mm (H) x 340mm (D)
WEIGHT 4.9kg
**All specifications are subject to change without notice.
User’s Manual
51
Appendix B: Remote Controller
A remote control is provided for the DVR unit. The function keys on the remote control are
listed as below figure:
User’s Manual
52
The keys of the remote control function as the keys of the front panel of the DVR. The only
difference between the remote control and the front panel keys is the “DVR SEL” key. The
DVR Selection key is used to switch control between each DVR.
The remote control can be used to control up to 16 DVRs. To setup the remote control, the
first thing you need to do is to assign a unique DVR Unit ID to each DVR.
Use the front panel of the DVR, and follow this path to change the DVR Unit ID, <Main
Menu> Æ <System Setup> Æ <RS485 Setup> Æ <Unit ID>
Change the DVR Unit ID to any number between 224 and 239, and exit the menu.
The ID Table is listed below for your reference.
DVR Unit ID 224 225 226 227 228 229 230 231
Remote Control # 1 2 3 4 5 6 7 8
DVR Unit ID 232 233 234 235 236 237 238 239
Remote Control # 9 10 11 12 13 14 15 16
After the DVR Unit ID is changed, you will need to setup the “DVR SEL” of the remote
control. Press “DVR SEL”, and then press the Remote Control # immediately to select the
DVR. For example, assuming that you have set the DVR Unit ID to 225, then you should
press “DVR SEL”, and then press “2” immediately. Now, the remote control will only be able
to control the specified DVR. Press “DVR SEL”, and then press the Remote control # to
switch between DVRs.
If you want to exit the single DVR control mode, press “DVR SEL”, and then press “ESC” to
do so.
User’s Manual
53
Appendix C: Setting up a DVR behind a Router
This appendix describes how to set up a router if the DVR connects to the internet via a
router.
To properly operate a web server, e.g. a DVR, the user has to set up both the IP and port of
the DVR, which are essential for data and command transmission. The port setting is
adjustable in OSD setup menu of the DVR and only one port is needed to do remote
operation. Typically and by the default, the DVR operates on port 80, which is well known
as the http port. Please make sure that port 80 is not blocked by your ISP or you will have
to find another available port and change the setting of the DVR.
In case a router or sometimes a DSL modem is in place, the real IP is now assigned to the
router instead of the DVR. The DVR is located behind the wall (router) and operates on
virtual IP. In most cases, virtual IP starts with 192.168.x.x. The router has two IP: one is
real IP (WAN IP), the other is virtual IP (LAN IP). The virtual IP would be 192.168.x.1.
When the remote user wants to operate the DVR, he will have to send command to the real
IP, i.e. the router. Then the router has to map (forward) the command to the DVR. Thus it is
required to set up the router for port mapping (forwarding) before you can remotely see
image from your DVR.
See your router manufacturer's websites for more instructions on port mapping.
User’s Manual
54
Following is an example of how the router should be set.
Router
(D-Link DI-724P+)
WAN IP: 218.160.54.13
LAN IP: 192.168.0.1
PC
IP: 192.168.0.100
DVR 1
IP: 192.168.0.167
Trigger port: 80
DVR 2
IP: 192.168.0.200
Trigger port: 81
• To change the setting of the router, you need a PC with web browser.
• Connect to D-Link DI-724P+ from PC via IE. The setup screen will be shown after
entering the correct username and password.
• Click the <Advanced> tab and follow the steps to set up web port forward to DVR 1.
User’s Manual
55
A. Select <Enabled> to set up the service.
B. Enter the name of the setting in the Name field: DVR 1.
C. Enter Private IP: 167
D. Choose <TCP> as the Protocol Type.
E. Enter Private Port: 80.
F. Enter Public Port: 80.
G. Click <Always> for the Schedule setting.
H. Click <Apply>.
• Click <Continue> to go on when the following screen displays.
• Follow the steps to set up web port forward to DVR 2.
A. Click <Enabled> to set up the service.
B. Enter the name of the setting in the Name field: DVR 2.
C. Enter Private IP: 200
D. Choose <TCP> as the Protocol Type.
E. Enter Private Port: 81.
F. Enter Public Port: 81.
G. Click <Always> for the Schedule setting.
H. Click <Apply>.
• Now you can see DVR 1 via http://218.160.54.13:80 and DVR 2 via
http://218.160.54.13:81.
• If there are more than one DVR behind the router, repeat the steps for port mapping
setting.
Loading...