Teledyne PPE 6 kV User Manual
HIGH VOLTAGE
PPE 6 kV
GENERAL CHARACTERISTICS
Operating temperature: 0 °C to 50 °C
Cable length: 2 m
Weight of probe + accessories: 70 gr
Coupling: 1 MΩ DC/AC
Warranty: One year
Overvoltage category: CAT I
Pollution degree: 1
CLEANING
The exterior of the probe only should be
cleaned with a soft cloth moistened with
either water or isopropyl alcohol.
USING AND MAINTENANCE
The probe user should note that the protection
provided by the equipment may be impaired,
if the equipment is used in a manner not
specified by the manufacturer.
To guarantee accurate performance
characteristics, machanical shocks should be
avoided, as well as damage to the cable
through excessive bending. Handle with care,
especially when the extra thin spring-tip is
fitted. All maintenance should be referred to
qualified personnel.
SALES & SERVICE LECROY
Corporate Headquarters
U.S.A.: Chestnut Ridge
Phone (1) 914 578 6020
Fax (1) 914 578 5985
European Headquarters
Germany: Heidelberg
Phone (49) 6221 827 00
Fax (49) 6221 834 655
S
AFETY INFORMATION
The probe is designed to be safe under the
following conditions:
Indoor use
Altitude to 2000 m
Temperature range from 0 °C to 50 °C
Maximum relative humidity 80 % for temperatures up to 31 °C, decreasing linearly
to 40 % relative humidity at 50 °C
WARNING
Do not disassemble or disconnect probes while
they are connected to a voltage source. Use only
grounded oscilloscopes.
Attention: Refer to this manual before
using the probe.
Danger. High Voltage.
10
100
1000
10000
0,1 1 10 100 1000
Frequency [MHz]
Voltage [V]
ELECTRICAL CHARACTERISTICS
System attenuation: 1000:1
System input resistance: 50 MΩ
Input capacitance: < 6 pF
Compensation range: 10 pF to 50 pF
System BW (-3 dB): 400 MHz typical
Max. non-destructive input voltage: 6 kV
See voltage derating curve
Impulse
DC + peak AC
LF PROBE ADJUSTMENT (1000:1)
Connect the probe to a 1 kHz square wave
signal. Adjust compensation trimmer in the
BNC-box for optimum square wave response.
Undershoot
Correct
Overshoot
HF PROBE ADJUSTMENT
The probe can be adjusted for high frequency if
necessary. Remove boot and isolation from
BNC-box. Connect the probe to 1 MHz square
wave signal. Turn the PCB in the BNC-box by 180 °
and adjust this trimmer for optimum square wave
response. Then replace all parts again in their
previous position.
Undershoot
Correct
Overshoot
STANDARD ACCESSORIES SUPPLIED
WITH THE PROBE
Accessories Quantities
1. Trimming tool 1
2. Sprung hook 1
3. IC Insulating tip (red) 1
4. Insulating tip (red) 1
5. Ground lead (22 cm) 1
6. BNC Adapter 1
7. Straight tip (0.8 mm) 1
8. Spring contact tip (0.8 mm) 1
9. Crocodile clip 1
10. Flexible 4 mm security adapter 1
11. Security ground lead 1
The following accessories are rated up to:
Sprung hook 1000 V
BNC Adapter 100 V
Crocodile clip 1000 V
Flexible 4 mm security adapter 1000 V
OPTIONAL PROBE KIT PK103
Same as standard accessories supplied with
probe, except for:
Straight tip (5 pieces)
Spring contact tip (5 pieces)
11
2
1
5
3
4
7
6
8
9
10
Loading...