Teledif TSA2 ver. T.tel Quick Installation Manual

working with love is a bond with our customers

TSA 2

ver. T.tel

Emergency Alarm and Commu-

nication System

For Analog Line

(PSTN)

TELEDIF ITALIA S.R.L.

Strada della Pronda 66/8 bis - 10142 TORINO - ITALY

Tel.: [phone] Fax: [phone]

Web: www.teledif.it E-mail: [e-mail]

Certified UNI EN ISO 9001:2008 Reg. n° ER/ES-1072/2002

4

Quick Installation Guide

SW 1.4

This document does not replace the User Guide that is available for free
download from our web site: www.teledif.it.
Our technical staff is available for any technical question.

1

WIRING DIAGRAM

CN1 (Power supply)
1: Positive (12 Vdc)
2: Negative (Ground)

CN3 (Alarm contacts)
1 e 2: Main / Cab

CN5 (Handsfree and Relay)
1: Ground
2: Speaker
3: Microfone
4: Power out (12 Vdc)
5: Relay 1 n.o.
6: Relay 1 common
7: Relay 2 n.o.

8: Relay 2 common

CN6 (Handset doorphone)
1: Speaker
2: Microfone
3: Ground

Example
TSA 2 Urmet 824/500
CN5-1 ­CN5-2 1
CN5-3 2
CN5-4 +

+

1

CN1

2

-

CN3

1

CN6

2
3

DLR1
DLV1

1
2
3

CN5

4
5
6
7
8

TR2

TR1

2
1

DLV1: Green LED “ON”
DLR1: Red LED “LINE”
TR1: Audio level from line to cab (CCW- / CW +)
TR2: Audio level from cab to line (CCW - / CW +)

INSTALLATION : Connect power taking care of the polarity
PROGRAMMING AND DATA READING: Dial TSA2 telephone number, wait for the message, then

dial:

•

Star (*) to access the system

•

Password (default password: 1234 )

•

Pound key (#) to start programming

•

Programming or reading according to the following sintax:
Write code (11) - parameter to write - star (*) - value - star (*)
Read code (12) - parameter to read
It is always possible to write more parameters using the same sequence. To terminate programming and
exit, digit pound key (#) or hang up.

The RED Led OFF means that the system is properly working.
The RED Led Fast Blinking means an error in the system (see User Guide).

Programming is always possible also with an active error.

Telephone

Line
(2 central
contacts)

SYSTEM SETTING

In order to properly manage the device from a Call Center it is strongly recommended that the unique
System ID Code is properly programmed (unique 6 digit number)
11 04 * <System ID, 6 digit>*

MAIN ALARM

1) Program at least one of the five numbers reserved to the main alarm
11 81 *<Tel. No.>*

2) Set the number of calling cycles (recommended endless=0)
11 20 *0*

REMOTE AUTO TEST (72 hours test)

1) Store the telephone number that will receive the 72 hours test calls and the delay time (in minutes)
to start the first call

11 88 *<Tel. No.>*
11 42 *<HH>*
11 43 *<mm>*

BATTERY ALARM

1) Store the telephone number that will receive the low battery alarm

11 89 *<Tel. No.>*

MESSAGES RECORDING

1) Store at least the main message including the information to locate the system

11 30 *<sec>*
Parameter 30 is the number of the message to record and <sec> is the duration of the message.
Repeat until the message is satisfactory recorded.

ANSWER TO A CALL GENERATED BY TSA 2

1) Listen to the message including the alarm type and the location

2) Use the following commands:

- 7 to listen again to the message

- 5 to start voice communication with the elevator cabin

- 4 to receive the alarm type and location from the system via DTMF tones

- 9 to close the communication

2

3