Teleco Voyager Digimatic SM 65, Voyager Digimatic SM 85, Voyager Digimatic 50 Installation Manual And User's Manual

UK

SHORT MAST 33 cm

INSTALLATION GUIDE

AND USER MANUAL

Information

Congratulations on your purchase! VOYAGER Digimatic SM 65/85 is among the most
technologically advanced products in the field of satellite TV reception. This handbook has
been prepared to provide information on how to install, use, maintain and technical specifications
your VOYAGER Digimatic SM 65/85.

For additional information, please contact your local dealer or directly the manufacturers:

TELECO s.p.a.

Via E. Majorana 49
48022 LUGO (RA)

Web site: www.telecogroup.com
Technical attendance: 899.899.856

TELECO .p.a. declines all responsibility for any errors contained in this manual. All the
contained information are up to the dates of printing and of the above-mentioned software
revisions. TELECO .p.a. reserves the right to introduce any modification made necessary by
the development of its products.

TELECO WARRANTY

Teleco guarantees its satellite dishes and terrestrial antennas against any
material and/or construction fault and defect. The warranty offered by TELECO
is limited to the free-of-charge replacement or repairing of any parts that are
deemed faulty by TELECO. The warranty is applicable for a period of 3
YEARS starting from the product purchase date; however, it will only be
considered valid if the Customer is able to produce a written document
(invoice or tax receipt) showing the purchase date.

The following is excluded from the TELECO warranty:

a. Damages caused by incorrect installation and/or use and/or maintenance
b. Damages resulting from product alterations not authorised by Teleco
c. Damages resulting from the use of spare parts different from original

Teleco parts

d. Damages resulting from repairs carried out by personnel not

authorised by Teleco
e. Normal part wear;
f. Expenses incurred for spare parts transport between the Customer's

and the service centre
g. Damages that may occur during transport:

the Customer shall always be responsible for transport risks.

1

…and then drill the outside wall.

Set the drilling jig in place. Drill in the
middle of the jig (page 22)

Using a dia. 42 cutter, drill the inside
wall first…

Caution:

Mount the antenna away from the vehicle
roof edge to avoid overhanding the roof
line when travelling.

The Voyager Digimatic antenna must
be installed near a vertical wall where
the wall outlet can be fitted

Installation instructions

2

Insert the mast roof mounting bracket in
the dia. 42 hole bored in the roof, making
sure you apply a layer of silicone under
the ring nut.

Fasten the ring nut using self-tapping
screws. Place the rubber gasket over the
ring nut. ( Screws not supplied )

Secure the pipe lead to the roof using
the ring nut and its wedge-shaped spacer .
Caution: the antenna must be in
horizontal position. The wedge-shaped
spacer is used to set the antenna in the
horizontal position even if the roof is
inclined.

Lock the collar on the wedge spacer
by applying the 2 screws (not supplied).

3

3,5x30

Introduce the
nut in its seat
on the back of
the wall outlet

Tight the locking ring nut
This mast locking device must be
screwed tight every time you wish to
secure the antenna in the desired position.
To turn or lift the mast, loosen this ring
nut.

Spread a thin film of Vaseline inside the
seal and introduce the mast

Fit the upper part of the wall outlet without
tightening all the way

Fix the outlet unit to the wall

4

Caution: Extend the dish mast
all the way as shown in the

figure

Tighten the indicator screw hard, to the
end of the thread as shown in the figure.

Insert the cable in the plastic handle hole

5

3.9X13
Screw with
pointed end

4X10

Screw

without

pointed end

Before fitting the plastic handle in the
tube, make sure that the holes A and C
are aligned with the reference mark B

Force the
flexible tongues
of the pointer
into the two slots
inside the
handle, then
push until they
come out of the
slots

Make sure that the cable runs in front
of the pointer reference mark B

Using the
screw, fasten
the plastic
handle to the
mast. Do not
turn the
handle while
carrying out
this operation
because the
tongues
might come
out of the
slots.

Insert the
crank in the
shaft square
seat and
tighten using
the special
bolt

Fasten the antenna to the
arm as shown in the figure.

6

Lower the dish until the right travelling position
is reached. Fix the steel plate to the roof with
cement or both-sides adhesive tape under the
LNB spacer

Make sure that
the antenna is
exactly in its
stowed
position. Place
the sticker on
the mast in
such a way
that you can
quickly lock the
antenna in the
right position
before every
start.

The antenna must be absolutely installed according to fig. 23, i.e.,
the disc must be bent to the rear of the vehicle.

7