TEL 1N4763A, 1N4763A, 1N4764A, 1N4764A, 1N4762A Datasheet

...
1N4741A THRU 1M200Z
GLASS PASSIVATED JUNCTION SILICON ZENER DIODE
VOLTAGE - 11 TO 200 Volts Power - 1.0 Watt
FEATURES
l Low profile package l Built-in strain relief l Glass passivated junction l Low inductance l Typical IR less than 5.0A above 11V l High temperature soldering :
260/10 seconds at terminals l Plastic package has Underwriters Laboratory Flammability Classification 94V-O
MECHANICAL DATA
Case: Molded plastic, DO-41 Epoxy: UL 94V-O rate flame retardant Lead: Axial leads, solderable per MIL-STD-202, method 208 guaranteed
DO-41
Polarity: Color band denotes cathode end Mounting position: Any Weight: 0.012 ounce, 0.3 gram
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Ratings at 25ambient temperature unless otherwise specified.
Peak Pulse Power Dissipation on TA=50(Note A) Derate above 50 Peak forward Surge Current 8.3ms single half sine-wave superimposed on rated load(JEDEC Method) (Note B) Operating Junction and Storage Temperature Range TJ,T
NOTES: A. Mounted on 5.0mm2(.013mm thick) land areas. B. Measured on 8.3ms, single half sine-wave or equivalent square wave, duty cycle = 4 pulses per minute maximum.
SYMBOL VALUE UNITS
PD 1.0
6.67
I
10 Amps
FSM
-55 to +150
STG
Watts
mW/
1N4741A THRU 1M200Z
*ELECTRICAL CHARACTERISTICS (TA=25unless otherwise noted) VF=1.2V max, IF=200mA for all types.
Surge Current
Type No. (Note 1.)
1N4741A 1N4742A 1N4743A 1N4744A 1N4745A 1N4746A 1N4747A 1N4748A 1N4749A 1N4750A 1N4751A 1N4752A 1N4753A 1N4754A 1N4755A 1N4756A 1N4757A 1N4758A 1N4759A 1N4760A 1N4761A 1N4762A 1N4763A 1N4764A
1M110Z 1M120Z 1M130Z 1M150Z 1M160Z 1M180Z 1M200Z
Nominal Zener
Voltage Vz @ I
volts
(Notes2. And
3.) 11
12 13 15 16 18 20 22 24 27 30 33 36 39 43 47 51 56 62 68 75 82
91 100 110 120 130 150 160 180 200
Test current
ZT
IZT
mA
23 21 19 17
15.5 14
12.5
11.5
10.5
9.5
8.5
7.5
7.0
6.5
6.0
5.5
5.0
4.5
4.0
3.7
3.3
3.0
2.8
2.5
2.3 2
1.9
1.7
1.6
1.4
1.2
Maximum Zener Impedance (Note 4.) Leakage Current
ZZT @ IZT
Ohms
8.0
9.0 10 14 16 20 22 23 25 35 40 45 50 60 70 80 95
110 125 150 175 200 250 350 450 550
700 1000 1100 1200 1500
ZZk @ IZK
Ohms
700 700 700 700 700 750 750 750 750
750 1000 1000 1000 1000 1500 1500 1500 2000 2000 2000 2000 3000 3000 3000 4000 4500 5000 6000 6500 7000 8000
IZK
mA
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
IR
A Max
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
VR
Volts
8.4
9.1
9.9
11.4
12.2
13.7
15.2
16.7
18.2
20.6
22.8
25.1
27.4
29.7
32.7
35.8
38.8
42.6
47.1
51.7
56.0
62.2
69.2
76.0
83.6
91.2
98.8
114.0
121.6
136.8
152.0
@ TA=25
Ir - mA
(Note 5.)
414 380 344 304 285 250 225 205 190 170 150 135 125 115 110
95 90 80 70 65 60 55 50 45
-
-
-
-
-
-
-
NOTE:
1.Tolerance and Type Number Designation. The type numbers listed have a standard tolerance on the nominal zener voltage of ±5%.
2.Specials Available Include: A. Nominal zener voltages between the voltages shown and tighter voltage tolerances. B. Matched sets.
3.Zener Voltage (VZ) Measurement. Guarantees the zener voltage when measured at 90 seconds while maintaining the lead temperature (TL) at 30±1, from the diode body.
4.Zener Impedance (ZZ) Derivation. The zener impedance is derived from the 60 cycle ac voltage, which results when an ac current having an rms value equal to 10% of the dc zener current (IZT or IZK) is superimposed on IZT or I
ZK.
5.Surge Current (Ir) Non-Repetitive. The rating listed in the electrical characteristics table is maximum peak, non-repetitive, reverse surge current of 1/2 square wave or equivalent sine wave pulse of 1/120 second duration superimposed on the test current, IZT, per JEDEC registration; however, actual device capability is as described in Figure 5.
Loading...
+ 3 hidden pages