Tektronix Y400 Setup Manual

Warning!

Layout

Installing/Removing Batteries

Connecting Power Adapters

To avoid injury, do not connect this product to any
source which may be subject to the effects of
lightning.

Important Safety Information

Review the following safety precautions to avoid
injury and prevent damage to this product or any
products connected to it.

Service. Only qualified personnel should perform

service procedures.

Power. Use only the Power cords, Desk Top Power

Supplies, Batteries, or In-Vehicle Power Adapters
specified for this product and certified for the country
of use. Observe all ratings marked on these parts.

Intended Use. The Y400 is intended for use only with

the specified application modules available from
Tektronix. Important safety information is contained
in the application module user manuals.

Read Application Module Manuals. Before operating

the Y400 NetTek Analyzer Platform, refer to the
application module manuals for:

H Detailed instructions on installing and charging

the battery. Recharge batteries for the recom­mended charge cycle only.

H System specifications, environmental ratings, and

electrical ratings.

H General safety warnings and cautions related to

operating the system and an explanation of the
safety symbols marked on the product.

H Proper use of controls and settings, and proper

connection of inputs and outputs.

H Proper use of the product’s shoulder strap, strand

hook, and other accessories.

H Proper application module installation.

H Proper system maintenance.

Batteries

External

power

Front panel

123 4

1. Power/Suspend button

2. Reset button

3. Status light

4. Battery charge/level light

Input and Output Ports

1

1. Microphone input

2. Headphone jack

3. Ethernet (RJ-45)

4. Serial (RS-232)

5. Keyboard

. USB host

6

7. USB slave

3

2

Application

modules

I/O ports

PC card

4567

1

Power adapter jack

Charging Batteries

2

Pull and lift tab:

Swing up retainer

3

Lift battery by strap

Retainer in
open position

1. Connect AC or DC power adapter to Y400.

2. Connect AC or DC power adapter to appropriate

power source. The battery charge/level light turns
green.

3. Battery charge time (full charge):

H Analyzer powered off: 4 hours

H Analyzer powered on: 8 hours

For more information on battery charging, battery
calibration, and power management, select Start >

Help > Windows CE Basics > Tektronix NetTek
Analyzer Platform Basics > Power Management.

Powering On and Off the Analyzer

To power on the NetTek Analyzer, press the
Power/Suspend button (blue button at lower left
corner of instrument). Powering up the NetTek
Analyzer takes about 30 seconds.

To power off the NetTek Analyzer, do one of the
following:

H Press the Power/Suspend button

H Select Start > Shutdown > Shutdown

For more information on the Shutdown menu
functions, select Start > Help > Windows CE Basics

> Tektronix NetTek Analyzer Platform Basics >
Shutting Down the Instrument

Copyright E Tektronix, Inc. All rights reserved

Calibrating the Touch-Screen Display

Cleaning

EMC Compliance

You must calibrate the touch-screen display to
respond correctly to your taps before using the
NetTek Analyzer.

1. Select Start > Settings > Control Panel.

2. Open (double-tap) the Stylus icon.

3. In the Double-Tap tab, double-tap the

checkerboard grid at a comfortable speed with a
stylus or your finger. This sets the tap rate
sensitivity.

4. Select the Calibration tab.

5. Follow the on-screen instructions to set the

touch-screen location and pressure values. Apply
pressure to the touch-screen for approximately
5 seconds to register each tap.

6. Tap OK to close the dialog box.

7. Restart the NetTek Analyzer to save and apply the

touch-screen calibration settings.

Online Help

To access Windows CE online help, select
Start > Help.

For NetTek Analyzer-specific help, select Start >

Help > Windows CE Basics > Tektronix NetTek
Analyzer Platform Basics.

Some application windows have context-sensitive
help, as indicated by a question mark icon at the top
of the application screen. Selecting the context-sensi­tive icon displays information about the active
application window.

Transportation and Lithium-Ion Batteries

Each Y400 lithium--ion battery pack contains less
than 8 grams of lithium, with individual cells each
containing less than 1.5 grams of lithium, as
measured by International Civil Aviation Organiza­tion (ICAO) standards. Consult your air carrier for
applicability and determination of any special
lithium--ion battery transportation requirements.

1. Disconnect the NetTek Analyzer from the external
power adapter.

2. Close all NetTek Analyzer connector and battery
doors.

3. Install the bus door on the NetTek Analyzer or
application module.

4. Use a soft cloth dampened with a solution of
water and mild detergent. Do not immerse the
analyzer or use abrasive cleaners.

CAUTION. To prevent damage to external
surfaces, do not use chemicals that contain
acetone, benzene, toluene, xylene, or similar
solvents. Do not use bleach or ammonia
solutions for cleaning.

Contacting Tektronix

Web site: www.tektronix.com

Phone: [phone]

Address: Tektronix, Inc.

Department or name (if known)
14200 SW Karl Braun Drive
P.O. Box 500
Beaverton, OR 97077
USA

Email: [e-mail]

Additional contact information is also located on the
online help system by selecting Start > Help >

Windows CE Basics > Tektronix NetTek Analyzer
Platform Basics > Contacting Tektronix.

For more information on the NetTek Analyzer,
including options and accessories, go to
www.tektronix.com and enter Y400 in the web page
search field.

EC Declaration of Conformity -- EMC
Meets intent of Directive 89/336/EEC for Electromagnetic

Compatibility. Compliance was demonstrated to the following
specifications as listed in the Official Journal of the European
Union:

EN 61326 EMC requirements for Class A electrical

equipment for measurement, control and
laboratory use.

IEC 61000-4-2 Electrostatic discharge immunity

(Performance criterion B)

IEC 61000-4-3 RF electromagnetic field immunity

(Performance criterion A)

IEC 61000-4-4 Electrical fast transient/burst immunity

(Performance criterion B)

IEC 61000-4-5 Power line surge immunity

(Performance criterion B)

IEC 61000-4-6 Conducted RF immunity

(Performance criterion A)

IEC 61000-4-11 Voltage dips and interruptions immunity

(Performance criterion B)
EN 61000-3-2 AC power line harmonic emissions
EN 61000-3-3 Voltage changes, fluctuations, and flicker
Australia/New Zealand Declaration of Conformity -- EMC
Complies with EMC provision of Radiocommunications Act per

the following standard(s):
AS/NZS 2064.1/2 Industrial, Scientific, and Medical

1

Platform EMC performance may be altered when operated
with an application module; EMC specifications for the
application module apply in that case.

2

EMC compliance was demonstrated using high-quality
shielded interface cables.

3

Emissions that exceed the limits of this standard may occur
when the instrument is connected to a test object.

4

Minimum Immunity test requirement.

2,3

Equipment: 1992

1,2,3,4

Y400
NetTekr Analyzer
Setup Reference

*P071143000*

071-1430-00

www.tektronix.com