Tektronix WVR6UP, WVR7UP, WVR6100 Series, WVR70UP, WVR7000 Series Instructions Manual
...
Instructions
WVR6UP, WVR70UP, and WVR7UP Upgrades
WVR6100, WVR7000, and WVR7100 Series
Waveform Rasterizers
075-0887-03
Warning
The servicing instructions are for use by qualified
personnel only. To avoid personal injury, do not
perform any servicing unless you are qualified to
do so. Refer to all safety summaries prior to
performing service.
www.tektronix.com
*P075088703*
075088703
Copyright © Tektronix. All rights reserved. Licensed software products are owned by Tektronix or its subsidiaries or
suppliers, and are protected by nat ional copyright laws and international treaty provisions.
Tektronix produc ts are covered by U.S. and foreign patents, issued and pending. Information in this publication supercedes
that in all previously published m aterial. Specifica tions and price change privileges reserved.
TEKTRONIX and TEK are registered trademarks of Tektronix, Inc.
Contacting Tektronix
Tektronix, Inc.
14200 SW Karl Braun Drive
P.O. Box 500
Beaverton, OR 97077
USA
For product information, sales, service, and technical support:
H In North America, call 1-800-833-9200.
H Worldwide, visit www.tektronix.com to find contacts in your area.
Service Safety Summary
Only qualified personnel should perform service procedures. Read this Service
Safety Summary and the General Safety Summary in the product service manual
or the instruction manual.
Do Not Service Alone. Do not perform internal service or adjustments of this
product unless another person capable of rendering first aid and resuscitation is
present.
Disconnect Power. To avoid electric shock, switch off the instrument power, then
disconnect the power cord from the mains power.
Use Care When Servicing With Power On. Dangerous voltages or currents may
exist in this product. Disconnect power, remove battery (if applicable), and
disconnect test leads before removing protective panels, soldering, or replacing
components.
To avoid electric shock, do not touch exposed connections.
WVR6UP, WVR70UP, and WVR7UP Upgrades
1
Service Safety Summary
2
WVR6UP, WVR70UP, and WVR7UP Upgrades
Kit Description
p
p
WVR70UPSD
FieldinstallsOptionSD,whichaddssupportforstandarddefinitionvide
o
WVR6U
P-A
D
aud
i
d
ded
aud
ioand
aud
iosigna
lsintheAES/EBU
WVR7U
P-DDand
Ana
logandDigitalaud
i
d
ded
aud
ioand
aud
i
WVR7U
P-DDE
D
igital(AC
)
decode,and
Ana
logandDigitalaud
i
f
W
V
W
V
wavef
a
y.W
V
ayj
a
vef
waveformdisplay.WVR6100instrumentsdisplayjitterwaveformsforSD
These instructions support field installation of all options currently available for
field installation in the WVR6100, WVR7000, and WVR7100 Waveform
Rasterizers. Find your kit in the table of kits supported that follows.
CAUTION. To prevent monitoring problems, after installing any audio option in
this kit, do not use the optional accessory, Analog/Audio Breakout Cable
Assembly, Tektronix part number 012-1658-01. This optional accessory is for
rasterizers that shipped with early versions of audio option hardware and will
not work properly with your new audio option. You can order part number
012-1688-00, which is an Analog/Audio Breakout Cable Assembly that will work
with your new audio option.
Kit Description
WVR70UP-SD
WVR7UP-SD
WVR70UP-DS
WVR6UP-DS
WVR7UP-DS
Field installs Option SD,whichadds su
signal monitoring to the WVR7000 or WVR7100.
Field installs Option DS, which adds support for Digital audio monitoring of
embedded audio and audio signals in the AES/EBU inputs.
ort for standard-definitionvideo
WVR70UP-AD
WVR7UP-AD
WVR6UP-DD
WVR6UP-DDE
WVR6UP-EYE
WVR7UP-EYE
WVR6UP-PHY
WVR7UP-PHY
Field installs Option AD, which adds support for Analog audio and Digital
omonitoring ofembe
inputs.
Field installs Option DD, which adds support for Dolby Digital (AC-3) decode
omonitoring ofembe
signals in the AES/EBU inputs.
Field installs Option DDE, which adds support for Dolby E decode, Dolby
-- 3
embedded audio and audio signals in the AES/EBU inputs.
Field installs Option EYE, which adds support for eye pattern monitoring of
the physical layer of video signals. WVR6100 instruments display eye
patternsfor SD signals;
also display eye patterns for SD signals if equipped with Option SD. (See
entry f or WVR7UP--SD in this table.)
Field installs Option PHY, which adds all of the capabilities of Option EYE
plus support for automated eye parameters measurement and ji tter
orm displ
signals; WVR7100 for HD signals. WVR7100 instruments also display jitter
waveforms for SD signals when equipped with Option SD. (See entry for
WVR7UP-SD in thi s table)
R7100for HD signals.
R6100 instruments displ
omonitoring o
R7100 instruments
itter w
ormsfor SD
o
WVR6UP, WVR70UP, and WVR7UP Upgrades
3
Kit Description
Products
WVR6100 Waveform Rasterizer All instruments
WVR7000 Waveform Rasterizer All instruments
WVR7100 Waveform Rasterizer All instruments
Minimum Tool and Equipment List
Required tools and equipment Part number
Screwdriver handle. Accepts TORX-driver bits. General tool. Used for
audio and EYE display options.
NA
T-10 TORX drive bit. Used for removing the rasterizer top cover. Used
for audi o and EYE display options.
T-15 TORX drive bit. Used for removing most of the screws on the
rasterizer. Used for audio and EYE display options.
3/16 Nutdriver. Used for removing and installing audio option boards
for audi o options only that have analog audio I/O connector.
5/16 Nutdriver. Used for loosening and tightening the nuts that secure
the fan bracket when installing a new Power Supply cable.
1/4 Nutdriver. Used for removing or installing internal audio board
mounting posts. Used for audio and EYE display options.
A st andard PC running Windows 98, Windows NT 4.0, Windows ME,
Windows 2000, or Windows XP. Used f or installing all options.
Winsock 2.0, an Et hernet int erface, and 10 MB of free disk space
must be present on the PC system. Used for installing all options.
NA
NA
NA
NA
NA
NA
NA
4
WVR6UP, WVR70UP, and WVR7UP Upgrades
Kit Parts Lists
Kit Description
WVR7UP-SD
WVR70UP-SD
WVR6UP-DS
WVR70UP-DS
WVR7UP-DS
Quantity Part number Description
1 each 020-2612-XX Documents CD
1 each 075-0887-XX Kit instructions
Quantity Part number Description
1 each 020-2612-XX Documents CD
1 each 075-0887-XX Kit instructions
3 each 129-1570-XX Post, spacer; 1.385 X 0.250 X 0.375 deep
1 each 174-4973-XX Cable assembly 80 POS. Cable with two 2X40 connectors
8 each 210-1039-XX Washer, lock; 0.521 ID; 0.025 thick
3 each 211-0722-XX Screw; 6--32 X 0.250, panhead T-- 15 TORX drive
8 each 220-0497-XX Nut; hex; 0.5--28 X 0.562
1 each 671-6072-XX Circuit-board assembly; Digital Audio
WVR6UP-AD
WVR70UP-AD
WVR7UP-AD
Quantity Part number Description
1 each 020-2612-XX Documents CD
1 each 075-0887-XX Kit instructions
3 each 129-1570-XX Post, spacer; 1.385 X 0.250 X 0.375 deep
1 each 131-7430-XX Connector, DSUB; male, 62 pins, 0.100 center, 30 gold
1 each 174-4973-XX Cable assembly 80 POS. Cable with two 2X40 connectors
8 each 210-1039-XX Washer, lock; 0.521 ID; 0.025 thick
3 each 211-0722-XX Screw; 6--32 X 0.250, panhead T-- 15 TORX drive
2 each 214-3903-XX Screw; 4--40 X 0.312 long, 0.188 H hex head stand off
8 each 220-0497-XX Nut; hex; 0.5--28 X 0.562
1 each 671-9938-XX Circuit-board assembly; Digital Analog Audio
WVR6UP, WVR70UP, and WVR7UP Upgrades
5
Kit Description
WVR6UP-DD
WVR7UP-DD
WVR6UP-DDE
WVR7UP-DDE
Quantity Part number Description
1 each 020-2612-XX Documents CD
1 each 075-0887-XX Kit instructions
3 each 129-1570-XX Post, spacer; 1.385 X 0.250 X 0.375 deep
1 each 131-7430-XX Connector, DSUB; male, 62 pins, 0.100 center, 30 gold
1 each 174-4973-XX Cable assembly 80 POS. Cable with two 2X40 connectors
8 each 210-1039-XX Washer, lock; 0.521 ID; 0.025 thick
3 each 211-0722-XX Screw; 6--32 X 0.250, panhead T-- 15 TORX drive
2 each 214-3903-XX Screw; 4--40 X 0.312 long, 0.188 H hex head stand off
8 each 220-0497-XX Nut; hex; 0.5--28 X 0.562
1 each 671-9938-XX Circuit-board assembly; Digital Analog Audio
Quantity Part number Description
1 each 020-2612-XX Documents CD
1 each 075-0887-XX Kit instructions
1 each 119-7167-XX Circuit-board assembly; Dolby E/Digital Decoder Module;
72 PIN SIM M
3 each 129-1570-XX Post, spacer; 1.385 X 0.250 X 0.375 deep
1 each 131-7430-XX Connector, DSUB; male, 62 pins, 0.100 center, 30 gold
1 each 174-4973-XX Cable assembly 80 POS. Cable with two 2X40 connectors
8 each 210-1039-XX Washer, lock; 0.521 ID; 0.025 thick
3 each 211-0722-XX Screw; 6--32 X 0.250, panhead T-- 15 TORX drive
2 each 214-3903-XX Screw; 4--40 X 0.312 long, 0.188 H hex head stand off
8 each 220-0497-XX Nut; hex; 0.5--28 X 0.562
1 each 671-9938-XX Circuit-board assembly; Digital Analog Audio
6
WVR6UP, WVR70UP, and WVR7UP Upgrades
Kit Description
WVR6UP-EYE
WVR7UP-EYE
Quantity Part number Description
1 each 020-2612-XX Documents CD
1 each 075-0887-XX Kit instructions
5 each 129-1604-XX Hardware; spacer post, .309 L, 6--32 male, 4--40 female
1 each 174-5224-XX Cable assembly, Power Supply to Main and Eye boards
1 each 174-5301-00 Coaxial cable, SMA
1 each 671-6099-XX Circuit board subassembly; SD, Eye board
Quantity Part number Description
1 each 020-2612-XX Documents CD
1 each 075-0887-XX Kit instructions
5 each 129-1604-XX Hardware; spacer post, .309 L, 6--32 male, 4--40 female
1 each 174-5224-XX Cable assembly, Power Supply to Main and Eye boards
2 each 174-5301-00 Coaxial cable, SMA
1 each 679-9935-XX Circuit board subassembly; Loop-through board
1 each 671-9936-XX Circuit board subassembly; HD/SD, Eye board
WVR6UP-PHY
WVR7UP-PHY
Quantity Part number Description
1 each 020-2612-XX Documents CD
1 each 075-0887-XX Kit instructions
5 each 129-1604-XX Hardware; spacer post, .309 L, 6--32 male, 4--40 female
1 each 174-5224-XX Cable assembly, Power Supply to Main and Eye boards
1 each 174-5301-00 Coaxial cable, SMA
1 each 671-6099-XX Circuit board subassembly; SD, Eye board
Quantity Part number Description
1 each 020-2612-XX Documents CD
1 each 075-0887-XX Kit instructions
5 each 129-1604-XX Hardware; spacer post, .309 L, 6--32 male, 4--40 female
1 each 174-5224-XX Cable assembly, Power Supply to Main and Eye boards
2 each 174-5301-00 Coaxial cable, SMA
1 each 679-9935-XX Circuit board subassembly; Loop-through board
1 each 671-9936-XX Circuit board subassembly; HD/SD, Eye board
WVR6UP, WVR70UP, and WVR7UP Upgrades
7
Kit Description
8
WVR6UP, WVR70UP, and WVR7UP Upgrades
Loading...