Tektronix WSTRO, WSTROU, WSTRM, TDS3EM, VCLNKP,VCLNKB User manual

Copyright © Tektronix, Inc. All rights reserved. Licensed software products are owned by Tektronix or its suppliers and are protected by United States copyright laws and international treaty provisions.
Use, duplication, or disclosure by the Government is subject to restrictions as set forth in subparagraph (c)(1)(ii) of the Rights in Technical Data and Computer Software clause at DFARS 252.227-7013, or subparagraphs (c)(1) and (2) of the Commercial Computer Software – Restricted Rights clause at FAR 52.227-19, as applicable.
Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication supercedes that in all previously published material. Specifications and price change privileges reserved.
Tektronix, Inc., P.O. Box 500, Beaverton, OR 97077 TEKTRONIX and TEK are registered trademarks of Tektronix, Inc.
VocalLink is a trademark of Tektronix, Inc.
Tektronix Software Solution V2.0 WSTRO & WSTROU WaveStar
Software for Oscilloscopes V2.4 WSTRM WaveStar Software for Meters V2.4 AD007 GPIB-LAN Adapter TDS3EM Ethernet Communications Module VCLNKP & VCLNKB VocalLinkt Software V1.2
071-0878-00

Preface

2
Preface
Tektronix Software Solutions is a suite of software products designed to connect, capture, and analyze data from Tektronix TDS/THS/CSA oscilloscopes and TX Series true RMS digital multimeters. Refer to the section in this booklet that pertains to your software and the product user manual for more information on each product.
This disk contains the following products:
H WSTRO WaveStar Software for Oscilloscopes (refer to page 3) H WSTROU Upgrade to update WaveStar Software for Windows 3.1 to
WSTRO WaveStar Software for Oscilloscopes (refer to page 6)
H Free 30-day Demo of WSTRO WaveStar Software for Oscilloscopes (refer to
page 8)
H WaveStar Reader (refer to page 9) H WSTRM WaveStar Software for Meters (refer to page 10) H AD007 GPIB-LAN Adapter software (refer to page 11) H TDS3EM Ethernet Communications Module TekVisa software (refer to
page 13)
H VCLNKB and VCLNKP VocalLink software (refer to page 14)
1
WSTRO WaveStar Software for Oscilloscopes
4
H TDS3EM Ethernet communications module for the TDS3000 Series oscil-
loscopes
H AD007 GPIB-LAN adapter H Infrared (IR)-to-RS-232 cable for TX-DMM (included with purchase of
WSTRM)

Starting WaveStar Software Installation

To begin the software installation, insert the installation disk into the CD-ROM drive. If the install menu does not appear, you can bring up the install menu as follows:

Windows 95/98

1. Click on the Start button in the Taskbar and select Run.
2. In the Open box, type: X:\install.exe
where X is the CD drive label.

3. Select OK. Windows NT 4.0

1. From the File menu, select Run.

WaveStar Software

WaveStar Software introduces a family of Windows 95, 98, and NT 4.0 applications that connect your Tektronix TDS/THS, CSA803, 11800 oscilloscope, or TX-DMM digital multimeter, to your PC desktop.

System Requirements

To install and run WaveStar software, you must have an Windows-based program with the following installed:
H Windows 95, 98, or NT 4.0 operating system H 16 MB RAM or greater recommended H CD-ROM drive, 4X or better H Super VGA monitor or better H 20 MB disk space H Appropriate interface hardware to communicate with your instrument:
H GPIB National Instruments IEEE 488.2 Interface Card H PC compatible serial communications port and RS-232 cable
3
WSTROU Upgrade to WaveStar for Oscilloscopes
6

Installing WSTROU WaveStar Upgrade Software

WSTROU Upgrade to WaveStar Software for Oscilloscopes upgrades your WaveStar for Windows 3.1 software to WaveStar for Oscilloscopes software, which runs on WIndows 95/98/NT 4.0 operating systems. WSTRO WaveStar Software for Oscilloscopes lets you capture, analyze, measure, control, and document Tektronix TDS, THS, and CSA oscilloscope information at your PC desktop.
You can install WSTROU only if you have the serial number from your WSTR31 WaveStar Software. This number can be found on the seal of the software license agreement envelope in which you received the WSTR31 installation disks, or on the WSTR31 floppy disk label.
Follow the steps below to install the upgrade to WaveStar Software for Oscillo­scopes:
1. Insert the CD-ROM into the CD-ROM drive. The main WaveStar installation
screen appears, with four tabs along the top. If the WaveStar menu does not display automatically, refer to page 4.
2. Select the WaveStar for Oscilloscopes tab. The installer opens the WaveStar
for Oscilloscopes information screen with a menu bar at the top of the installer screen.
2. In the Command Line box, type: X:\install.exe
where X is the CD drive label.
3. Select OK.

Installing WSTRO WaveStar Software for Oscilloscopes

WSTRO WaveStar Software is a Windows 95/98/NT 4.0 application that lets you capture, analyze, measure, control, and document Tektronix TDS, THS, and CSA oscilloscope waveforms and measurements from your PC desktop.
Follow the steps below to install WSTRO WaveStar Software for Oscilloscopes:
1. Insert the CD-ROM into the CD-ROM drive. The main WaveStar installation
screen appears, with four tabs along the top. If the WaveStar menu does not display automatically, refer to page 4.
2. Select the WaveStar for Oscilloscopes tab. The installer opens the WaveStar
for Oscilloscopes information screen with a menu bar at the top of the installer screen.
3. Select Install in the menu bar. The installation wizard appears next and walks
you through the rest of the installation process. Follow the instructions in the wizard. When prompted, select WaveStar Software for Oscilloscopes –Purchase required. You will need to enter the key code provided with WSTRO; keep the key code handy.
WSTRO WaveStar Software for Oscilloscopes
5
Free 30-Day Demo
8

Installing Free 30-Day WaveStar for Oscilloscopes Demo Software

The free 30-day demo is a full featured version of WSTRO WaveStar Software for Oscilloscopes that expires thirty days after installation. WSTRO WaveStar Software for Oscilloscopes lets you capture, analyze, measure, control, and document Tektronix TDS, THS, and CSA oscilloscope information at your PC desktop.
Follow the steps below to install the free 30-day demo:
1. Insert the CD-ROM into the CD-ROM drive. The main WaveStar installation
screen appears, with four tabs along the top. If the WaveStar menu does not display automatically, refer to page 4.
2. Select the WaveStar for Oscilloscopes tab. The installer opens the WaveStar
for Oscilloscopes information screen with a menu bar at the top of the installer screen.
3. Select Install in the menu bar. The installation wizard appears next and walks
you through the rest of the installation process. Follow the instructions in the wizard. When prompted, select WaveStar Software DEMO to load the demo software.
3. Select Install in the menu bar. The installation wizard appears next and walks
you through the rest of the installation process. Follow the instructions in the wizard. When prompted, select WaveStar Software for OscilloscopesPurchase required.
4. You will need to enter the serial number from your WSTR31 software as well
as the new key code provided with WSTROU; keep these numbers handy.
WSTROU Upgrade to WaveStar for Oscilloscopes
7
WSTRM WaveStar Software for Meters
10

Installing WSTRM WaveStar Software for Meters

WSTRM WaveStar Software for Meters is a Windows 95/98/NT 4.0 application that lets you capture, analyze, measure, control, and document Tektronix TX-DMM series meter information at your PC desktop.
Follow the steps below to install WaveStar Software for Meters:
1. Insert the CD-ROM into the CD-ROM drive. The main WaveStar installation
screen appears, with four tabs along the top. If the WaveStar menu does not display automatically, refer to page 4.
2. Select the WaveStar for Meters tab. The installer opens the WaveStar for
Meters information screen with a menu bar at the top of the installer screen.
3. Select Install in the menu bar. The installation wizard appears next and walks
you through the rest of the installation process. Follow the instructions in the wizard.

Installing WaveStar Reader

WaveStar Reader is a free program that lets you view existing data sheet and notebook files in a WaveStar-like window, and can be loaded on any number of PCs.
Follow the steps below to install WaveStar Reader:
1. Insert the CD-ROM into the CD-ROM drive. The main WaveStar installation
screen appears, with four tabs along the top. If the WaveStar menu does not display automatically, refer to page 4.
2. Select the WaveStar for Oscilloscopes tab. The installer opens the WaveStar
for Oscilloscopes information screen with a menu bar at the top of the installer screen.
3. Select Install in the menu bar. The installation wizard appears next and walks
you through the rest of the installation process. Follow the instructions in the wizard. When prompted, select WaveStar Reader to load the WaveStar reader software.
WaveStar Reader
9
AD007 GPIB-LAN Adapter
12

AD007 Software Installation

Follow the steps below to install the AD007 software:
1. Insert the CD-ROM into the CD-ROM drive. The main WaveStar installation
screen appears, with four tabs along the top. If the WaveStar menu does not display automatically, refer to page 4.
2. Select the AD007 tab. The installer opens the AD007 information screen with
a menu bar at the top of the installer screen.
3. Select Install in the menu bar. The installation wizard appears next and walks
you through the rest of the installation process. Select the desired installation options and follow the instructions in the wizard.

AD007 GPIB-LAN Adapter Software

The AD007 adapter allows GPIB devices to talk or listen to networked computers and peripherals through a 10Base-T Ethernet connection.

System Requirements

The AD007 adapter requires the following system components for installation and operation.
H IBM-compatible PC with Windows 95, 98, or NT 4.0 operating system H CD ROM drive H Web browser H 10Base-T Ethernet card H 10Base-T LAN connection with a server that supports BOOTP or DHCP H LPD-compatible print server for network printing
11
14

VocalLink Software

The VocalLink software installs on a PC that connects to a Tektronix TDS500, TDS600, TDS700, TDS3000, or TDS7000 series oscillo­scopes. VocalLink software will install TekVisa software in order to communicate with these oscilloscopes.

System Requirements

To install and run VocalLink software, you must have an Windows­based operating system with the following minimum configuration.
TDS 7000 series oscilloscopes meet the system requirements to operate VocalLink software.
H Microsoft Windows 95, 98, 2000, or Windows NT 4.0 H 166 MHz Pentium processor H 32 MB RAM H Sound card with an amplifier H Noise cancelling microphone headset (supplied) H CD-ROM drive, 4X or better

Installing TDS3EM

The TDS3EM Ethernet communication module connects your TDS3000 Series oscilloscope to any 10baseT Ethernet LAN. WaveStar needs to install TekVisa software in order to communicate with the TDS3EM module.
Follow the steps below to install TekVisa software for the TDS3EM module:
1. Insert the CD-ROM into the CD-ROM drive. The main WaveStar installation
2. Select the TDS3EM tab. The installer opens the TDS3EM information screen
3. Select Install in the menu bar. The installation wizard appears next and walks
NOTE. If you already installed TekVisa as part of WaveStar Software for
Oscilloscopes or Meters, you do not need to install the TDS3EM TekVisa software; it is the same software.
screen appears, with four tabs along the top. If the WaveStar menu does not display automatically, refer to page 4.
with a menu bar at the top of the installer screen.
you through the rest of the installation process. Follow the instructions in the wizard.
13
VocalLink Software
16

Installing VocalLink Software

To install VocalLink software for a supported oscilloscope follow these steps:
NOTE. If you already installed TekVisa as part of another software
package for oscilloscopes, you do not need to install the VocalLink TekVisa software; it is the same software.
1. Insert the CD-ROM into the CD-ROM drive. Typically, the CD-ROM drive
automatically runs the installation program. If it does not, use the following instructions:
To install VocalLink, select Start > Run, and type
<CDĆROM drive mapping>:\VL\setup.exe
To install TekVisa, select Start > Run, and type
<CDĆROM drive mapping>:\Tekvisa\setup.exe
NOTE. In the TDS7000 Series oscilloscope, the CD-ROM drive mapping
is located on the D drive.
2. Select the VocalLink tab. The installer opens the V ocalLink information screen.
VocalLink Software
H Super VGA monitor or better H 20 MB of disk space H TekVisa software (supplied) or other VISA software H Install one of the following: GPIB controller card and cable,
AD007 GPIB-LAN Adapter, RS-232 COM port (TDS 3000 only), or a 10baseT Ethernet LAN.
NOTE. For optimum performance, you need 233 MHz and 64 MB of
RAM. On minimum-configured machines, close all other programs before running VocalLink software.
15
VocalLink Software
18
VocalLink Software
3. Select Install in the menu bar. The installation wizard appears next and walks
you through the rest of the installation process. Follow the instructions in the wizard.
NOTE. When the installer displays the dialog asking for your name,
company, and keycode, enter your VocalLink 14-character software keycode attached to your CD case; keep this number handy.
17
Loading...