Instructions
020-2664-00
TLA7012 Portable Logic Analyzer
Rackmount Kit
071-1750-00
Warning
The servicing instructions are for use by qualified
personnel only. To avoid personal injury, do not
perform any servicing unless you are qualified to
do so. Refer to all safety summaries prior to
performing service.
www.tektronix.com
*P071175000*
071175000
Copyright © Tektronix, Inc. All rights reserved. Licensed software products are owned by Tektronix or its subsidiaries or
suppliers, and are protected by national copyright laws and international treaty provisions.
Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication supercedes
that in all previously published material. Specifications and price change privileges reserved.
TEKTRONIX and TEK are registered trademarks of Tektronix, Inc.
Contacting Tektronix
Tektronix, Inc.
14200 SW Karl Braun Drive
P.O. Box 500
Beaverton, OR 97077
USA
For product information, sales, service, and technical support:
H In North America, call 1-800-833-9200.
H Worldwide, visit www.tektronix.com to find contacts in your area.
Service Safety Summary
Only qualified personnel should perform service procedures. Read this Service
Safety Summary and the General Safety Summary in the product service manual
or the instruction manual.
Do Not Service Alone. Do not perform internal service or adjustments of this
product unless another person capable of rendering first aid and resuscitation is
present.
To prevent the instrument and rack from falling onto the operator, two or more
installers should install the instrument into the rack cabinet. After completing the
installation procedure, the installers should verify that the instrument and rack
cabinet will not tip forward while the instrument is in the extended position.
Disconnect Power. To avoid electric shock, switch off the instrument power, then
disconnect the power cord from the mains power.
Use Care When Servicing With Power On. Dangerous voltages or currents may
exist in this product. Disconnect power and disconnect test leads before
removing protective panels, soldering, or replacing components.
To avoid electric shock, do not touch exposed connections.
TLA7012 Portable Logic Analyzer Rackmount Kit Instructions
1
Service Safety Summary
2
TLA7012 Portable Logic Analyzer Rackmount Kit Instructions
Kit Description
Products
This introduction describes the installation of the rackmount kit to your standard
portable instrument.
CAUTION. This kit requires you to remove the right-side panel of the instrument
rack you intend to use. Y ou must have access to the right side of your instrument
to connect the logic analyzer probes when the instrument is installed in the rack.
The rackmount kit is a collection of parts that, once installed, configure the
instrument for mounting into a standard 19-inch equipment rack.
TLA7012 AllSerialNumbers
TLA7012 Portable Logic Analyzer Rackmount Kit Instructions
3
Kit Description
Figure 1: Completed rackmount installation
4
TLA7012 Portable Logic Analyzer Rackmount Kit Instructions
Kit Parts List
Kit Description
Figure 2
on page 6
-- -- -- -- -- -- -- -- -- 1ea 020-2664-XX RACKMOUNT KIT TLA7012 CONSISTING OF
-- -- -- -- -- -- -- -- -- 1 e a 071-1750-00 TECH MANUAL: INSTRUCTIONS, TLA7012
11ea436-0426-00 CHASSIS ASSY, TLA7012 RACKMOUNT,
21ea407-5122-00 BRACKET, LOCKING
32ea386-7459-00 PANEL, COSMETIC
41ea351-1119-00 GUIDE, SLIDE (RACKMOUNT, L AND R)
52ea407-5125-00 BRACKET, RACKMOUNT GUIDE, SET OF 4
61ea407-5131-00 BRACKET, PORT RACKMNT ADAPTER (R)
Quantity Part number Description
THE FOLLOWING:
INCLUDES 6-32 AND 10-32 SCREWS
W/HARDWARE
71ea407-5124-00 BRACKET, PORT RACKMNT ADAPTER (L)
8 2ea 367-0530-00 HANDLE: BOW
NS - Not Saleable
TLA7012 Portable Logic Analyzer Rackmount Kit Instructions
5
Kit Description
2
1
4
8
6
7
5
3
Figure 2: Rackmount kit parts
6
TLA7012 Portable Logic Analyzer Rackmount Kit Instructions
Loading...