Tektronix TBS1052B EDU, TBS1072B EDU, TBS1102B EDU, TBS1152B EDU, TBS1202B EDU Performance Verification

...
x
TBS1000B and TBS1000B-EDU Series Oscilloscopes Specications and Performance Verication
ZZZ
Technical Reference
*P077102500*
077-1025-00
xx
TBS1000B and TBS1000B-EDU Series Oscilloscopes Specications and Performance Verication
ZZZ
Technical Reference
Register now!
Click the following link to protect your product.
www.tektronix.com/register
www.tektronix.com
077-1025-00
Copyright © Tektronix. All rights reserved. Licensed software products are owned by Tektronix or its subsidiaries or suppliers, and are protected by na
tional copyright laws and international treaty provisions.
Tektronix pro previously published material. Specications and price change privileges reserved.
TEKTRONIX and TEK are registered trademarks of Tektronix, Inc.
ducts are covered by U.S. and foreign patents, issued and pending. Information in this publication supersedes that in all
Contacting Tektronix
Tektronix, Inc. 14150 SW Karl Braun Drive P.O. Box 500 Beaverton, OR 97077 USA
For product i nformation, sales, service, and technical support:
In North America, call 1-800-833-9200. Worldwide, visit www.tektronix.com to nd contacts in your area.
Table of Contents
Important safety information .......................................................................................................... iii
General safe
Service safety summary ......................................................................................................... vi
Terms in this manual ........ . . . . . . . . . . . .............. . . . . . . . . . . .............. . . . . . . . . . . .............. . . . . . . . . . . .............. . . . vii
Symbols and
Specications .......................................................................................................................... 1
Signal Acquisition System Characteristics...................................................................................... 1
Time Base S
Triggering System........... . . . . . . . . . . . ............. . . . . . . . . . . . ............. . . . . . . . . . . . ............. . . . . . . . . . . . ............. . . . . .9
Display Specications........................................................................................................... 13
Interface
Data Handling Characteristics . . . . . . .............. . . . . . . . . . . .............. . . . . . . . . . . ............... . . . . . . . . . . .............. . . . . . 14
Power Distribution System...................................................................................................... 14
Mechanic
EnvironmentalPerformance.................................................................................................... 15
Data Logging System Characteristics........ . . . . . . . . . . . ............. . . . . . . . . . . . .............. . . . . . . . . . . ............. . . . . . . . . . . 15
Limit Te
Performance Verication ............................................................................................................. 17
Required Equipment ........... . . . . . . . . . . ............ . . . . . . . . . . ............ . . . . . . . . . .............. . . . . . . . . . . ............ . . . . . . . . 17
Test R e
Performance Verication Procedures . . . . . . . .............. . . . . . . . . . . ............ . . . . . . . . . ............. . . . . . . . . . . . ............ . . 18
Example of a Vertical Position Accuracy Test Spreadsheet . . . . . . . ................. . . . . . . . . . . ................. . . . . . . . . . . ........... 29
Sample Filled-In Vertical Position Accuracy Test Spreadsheet ............. . . . . . . . . . . . .............. . . . . . . . . . . . .............. 29
ex
Ind
ty summary......................................................................................................... iii
terms on the product............. . . . . . . . . . . . .............. . . . . . . . . . . . .............. . . . . . . . . . . . ................ . . . vii
ystem ............................................................................................................... 5
s and Output Ports Specications .................................................................................... 13
al Characteristics..................................................................................................... 14
sting System Characteristics........................................................................................... 16
cord...................................................................................................................... 18
Self Test.................................................................................................................... 19
libration............................................................................................................. 19
Self Ca
Check DCGain Accuracy ................................................................................................. 19
Check Bandwidth . . . ............ . . . . . . . . . . ........... . . . . . . . . . . ............ . . . . . . . . . . ............ . . . . . . . . . ............ . . . . . 20
Sample Rate Accuracy and Delay Time Accuracy ............................................................... 21
Check
Check Edge Trigger Sensitivity . . . . . . . . .............. . . . . . . . . . . ............ . . . . . . . . . .............. . . . . . . . . . . ............ . . 22
Check External Edge Trigger Sensitivity........... . . . . . . . . . . ............. . . . . . . . . . . ............. . . . . . . . . . . . ............. . 24
k Vertical PositionAccuracy......................................................................................... 25
Chec
Table of Content
s
TBS1000B and TBS1000B-EDU Specications and Performance Verication i
Table of Content
s
ii TBS1000B and TBS1000B-EDU Specications and Performance Verication
Important safet
y information
Important saf
This manual contains information and warnings that must be followed by the user for safe operation and to keep the product in a safe condition.
To safely perform service on this product, additional information is provided at the end of this section. (See page vi, Service safety summary.)
ety information
General safety summary
Use the product only as specied. Review the following safety precautions to avoid injury and prevent damage to this product or any products connected to it. Carefully read all instructions. Retain these instructions for future reference.
Comply with local and national safety codes.
For correct and safe operation of the product, it is essential that you follow generall to the safety precautions specied in this manual.
The product is designed to be used by trained personnel only.
Only qualied personnel who are aware of the hazards involved should remove the cover for repair, maintenance, or adjustment.
Before use, alway
This product is not intended for detection of hazardous voltages.
s check the product with a known source to be sure it is operating correctly.
y accepted safety procedures in addition
Use personal protective equipment to prevent shock and arc blast injury where hazardous live conductors are exposed.
While using this product, you may need to access other parts of a larger system. Read the safety sections of the other component manuals for warnings and cautions related to operating the system.
When incorporating this equipment into a system, the safety of that system is the responsibility of the assembler of the system.
To avoid re or personal injury
Use proper power cord. Use
Do not use the provided power cord for other products.
Ground the product. This product is grounded through the grounding conductor of the power cord. To avoid electric
shock, the grounding conductor must be connected to earth ground. Before making connections to the input or output terminals of the product, make sure that the product is properly grounded.
Do not disable the power cord grounding connection.
Power disconnect.
Do not position the equipment so that it is difcult to disconnect the power switch; it must remain accessible to the user at all times to allow for quick disconnection if needed.
The power switch disconnects the product from the power source. See instructions for the location.
Connect and disconnect properly. Do not connect or disconnect probes or test leads while they are connected
to a voltage source.
Use only insulated voltage probes, test leads, and adapters supplied with the product, or indicated by Tektronix to be suitable for the product.
only the power cord specied for this product and certied for the country of use.
TBS1000B and TBS1000B-EDU Specications and Performance Verication iii
Important safet
Observe all terminal ratings. To avoid re or shock hazard, observe all ratings and markings on the product. Consult
the product man Category (CAT) rating and voltage or current rating of the lowest rated individual component of a product, probe, or accessory. Use caution when using 1:1 test leads because the probe tip voltage is directly transmitted to the product.
Do not apply a potential to any terminal, including the common terminal, that exceeds the maximum rating of that terminal.
Do not oat the common terminal above the rated voltage for that terminal.
Do not operate without covers. Do not operate this product with covers or panels removed, or with the c ase open.
Hazardous voltage exposure is possible.
Avoid exposed circuitry. Do not touch exposed connections and components when power is present.
Do not operate with suspected failures. If you suspect that there is damage to this product, have it inspected by
qualied service personnel.
Disable the product if it is damaged. Do not use the product if it is damaged or operates incorrectly. If in doubt about safety of the product, turn it off and disconnect the power cord. Cl early mark the product to prevent its further operation.
Before use, inspect v oltage probes, test leads, and accessories for mechanical damage and replace when damaged. Do not use probes or test leads if they are damaged, if there is exposed metal, or if a wear indicator shows.
Examine the exterior of the product before you use it. Look for cracks or missing pieces.
y information
ual for further ratings information before making connections to the product. Do not exceed the Measurement
Use only specied replacement parts.
Use proper fuse. Use only the fuse type and rating specied for this product.
Wear eye protection. Wear eye protection if exposure to high-intensity rays or laser radiation exists.
Do not operate in wet/damp conditions. Be aware that condensation may occur if a unit is moved from a c old to a
warm environment.
Do not operate in an explosive atmosphere.
Keep product surfaces clean and dry.
Remove the input signals before you clean the product.
Provide proper ventilation. Refer to the installation instructions in the manual for details on installing the product
so it has proper ventilation.
Slots and openings are provided for ventilation and should never be covered or otherwise obstructed. Do not push objects into any of the openings.
Provide a safe working environment. Always place the product in a location convenient for v iewing the display
and indicators.
Avoid improper or prolonged use of keyboards, pointers, and button pads. Improper or prolonged keyboard or pointer use may result in serious injury.
Be sure your work area meets applicable ergonomic standards. Consult with an ergonomics p ro fessional to avoid stress injuries.
Probes and test leads
Before connecting probes or test leads, connect the power cord from the power connector to a properly grounded power outlet.
iv TBS1000B and TBS1000B-EDU Specications and Performance Verication
Important safet
Keep ngers behind the nger guards on the probes.
Remove all probes, test leads and accessories that are not in use.
Use only correct Measurement Category (CAT), voltage, temperature, altitude, and amperage rated probes, test leads, and adapters f
or any measurement.
y information
Beware of high voltages. Understand the voltage ratings for the probe you are using and do not exceed those ratings.
Two ratings are important to know and understand:
The maximum measurement voltage from the probe tip to the probe reference lead.
The m aximum oating voltage from the probe reference lead to earth ground
These two voltage ratings depend on the probe and your application. Refer to the Specications section of the manual for more information.
WARNING. To prevent electrical shock, do not exceed the maximum measurement or maximum oating voltage for the
oscilloscope input BNC connector, probe tip, or probe reference lead.
Connect and disconnect properly. Connect the probe output to the measurem ent product before connecting the
probe to the circuit under test. Connect the probe reference lead to the circuit under test before connecting the probe input. Disconnect the probe input and the probe reference lead from the circuit under test before disconnecting the probe from the measurement product.
Connect and disconnect properly. De-energize the circuit under test before connecting or disconnecting the current
probe.
Connect the pro
Do not connect a
be reference lead to earth ground only.
current probe to any wire that carries voltages above the current probe voltage rating.
Inspect the probe and accessories. Before each use, inspect probe and accessories for damage (cuts, tears, or
defects in the probe body, accessories, or cable jacket). Do not use if damaged.
Ground-referenced oscilloscope use. Do not oat the reference lead of this probe when using with ground-referenced
oscilloscopes. The reference lead must be connected to earth potential (0 V).
TBS1000B and TBS1000B-EDU Specications and Performance Verication v
Important safet
y information
Servicesafetysummary
The Service safety summary section c ontains additional information required to safely perform service on the product. Only qualied personnel should perform service procedures. Read this Service safety summary and the General safety summary before performing any service procedures.
To avoid electric shock. Do not touch exposed connections.
Do not service alone. Do not perform internal service or adjustments of this product unless another person capable of
rendering rst aid and resuscitation is present.
Disconnect
power before removing any covers or panels, or opening the case for servicing.
power.
To avoid electric shock, switch off the product power and disconnect the power cord from the mains
Use care when servicing with power on. Dangerous voltages or currents may exist in this product. Disconnect
power, remove battery (if applicable), and disconnect test leads before removing protective panels, soldering, or replacing components.
Verify sa
fety after r epair.
Always recheck ground continuity and mains dielectric strength after performing a repair.
vi TBS1000B and TBS1000B-EDU Specications and Performance Verication
Terms in this manual
These terms may appear in this manual:
WARNING. Warning statements identify conditions or practices that could result in injury or loss of life.
CAUTION. Caution statements identify conditions or practices that could result in damage to this product or other property.
Symbols and terms on the product
These terms may appear on the product:
DANGER indicates an injury hazard immediately accessible as you read the marking.
WARNING indicates an injury hazard not immediately accessible as you read the marking.
CAUTION indicates a hazard to property including the product.
Important safet
y information
When this symbol is marked on the product, be sure to consult the manual to nd out the nature of the potential hazards and any actions which have to be taken to avoid them. (This symbol may also be used to refer the user to ratings
The following symbol(s) m ay appear on the product:
in the manual.)
TBS1000B and TBS1000B-EDU Specications and Performance Verication vii
viii TBS1000B and TBS1000B-EDU Specications and Performance Verication
Specications
Specication
These specications apply to all TBS1000B series oscilloscopes. To v erify that an oscilloscope meets specications, it mustrst meet the following conditions:
The oscilloscope must have been operating continuously for twenty minutes within the specied operating temperature.
You must perform the Do Self Cal operation, accessible through the Utility menu, if the operating temperature has changed by more than 5 °C (9 °F) since the last time the Do Self Cal operation was performed.
The oscilloscope must be within the factory calibration interval of one year.
Specications are provided in the following tables. All specications are guaranteed unless noted "typical." Specications that are marked with the symbol are checked in the Performance Verication section. (See page 17, Performance Verication.)
s
Signal Acquisition System Characteristics
NOTE. A ll amplitude-related or modied specications require 1X probe attenuation factors unless otherwise specied.
This is due to the way the displayed sensitivity works. This does not affect actual methods of attachment. It only alters the relationship between displayed scale factors and the specications.
Table 1: Signal acquisition system characteristics
Characteristic
Number of Input Channels
Input Impedance, DC Coupled
Maximum Input Voltage
Bits
Sensitivity Range 2 mV/div to 5 V/div in 1-2-5 sequence with the probe attenuation set to 1X.
Description
Two
DC, AC, or GNDInput Coupling AC coupling connects a capacitor in series with the i nput circuitry. The DC input impedance
becomes very high, since capacitance is in series with all paths to ground. Ground coupling mode provides a reference waveform derived from the v alues identied during
SPC. This reference waveform shows visually where ground is expected to be. 1MΩ ±2%inparallelwith20pF±3pF
At the front panel connector, 300 V 100 kHz to 13 V peak AC at 3 MHz and above.
Based on sinusoidal or DC input signal. The maximum viewable signal while DC coupled is ±50 V offset ±5 V/div at 4 divisions, or 70 V. AC coupling allows measuring signals on a DC level up to 300 V. For nonsinusoidal waveforms, peak value must be less than 450 V. Excursions above 300 V should be less than 100 ms in duration, and the duty factor is limited to 44%. The RMS signal level must be limited to 300 V. If these values are exceeded, damage to the instrument may result.
8 bits except at 2 mV/divNumber of Digitized Displayed vertically with 25 digitization levels per division, 10 divisions dynamic range. 2 mV/div setting is generated by digital multiplication and the resolution is reduced. Given 100
levels available, the resolution is >6.5 bits.
, Installation Category II; derate at 20 dB/decade above
RMS
TBS1000B and TBS1000B-EDU Specications and Performance Verication 1
Specications
Table 1: Signal acquisition system characteristics (cont.)
Characteristic
Display Gain Variable
Probe Scale Factors
Acquisition Modes
Retained Front Panel Settings
Math Modes All Units :
Voltage Measurement Functions
DC Gain Accuracy, Sample or Average Acquisition
Measurement Accuracy, Average Acquisition Mode
Description
The Display Gain Variable function allows the user to vary the vertical display gain continuously over the full range.
Resolution is that of the coarse gain from which these data are constructed. Fine gain values (for instance 120 mV/div) are acquired at the next higher coarse gain setting (in this case 200 mV/div).
The Display Gain Variable is achieved by digital multiplication of the data to obtain the settings between the 1-2-5 gain settings.
Hard copy outputs to printer will be exactly the same as seen on screen even when the Display Gain Variable is u sed.
However, WAVEFORM DATA obtained through the I/O interface i s limited to the 1-2-5 gain settings.
1X, 10X, 20X, 50X, 100X, 500X, 1000X voltage attenuation. 5, 1, 500 m, 200 m, 100 m, 20 m, 10 m, 1 m V/A current scale factor. This adjusts the display scale factor of the instrument to accommodate various probe types. Accuracy of the probe used must be added to the accuracy specications of instrument. No automatic probe interface is provided, so you must verify that the settings match the probe
characteristics. The probe check function allows setting of the proper attenuation for voltage probes.
Sample, Peak Detect, Average Envelope mode not provided Front panel settings are retained when the instrument power is turned off and on with the power
switch. The settings are retained when the line power is turned off and on. The instrument periodically saves front panel settings after settings are changed. There is a
delay of three seconds after the last change and before the storage of the settings in memory.
Channel 1 – Channel 2 Channel 2 – Channel 1 Channel 1 + Channel 2 Channel 1 * Channel 2
Mean, Cycle Mean, Cursor Mean, Max, Min, RMS, Cycle RMS, Cursor RMS, Peak-to-Peak., Amplitude, Positive O vershoot, Negative Overshoot, High, Low
This is the difference between the measured DC gain and the nominal DC gain, divided by the nominal DC gain and expressed as a percent.
±3%, 5 V/div through 10 mV/div ±4%, 5 mV/div and 2 mV/div This is the accuracy of DC voltage measurements acquired using Average of > 16 waveforms.DC Voltage
Vertical position = 0: ±(3% of |reading| + 0.1 div + 1 mV) Vertical position 0 and vertical scale = 2 mV/div to 200 mV/div: ±[3% of |reading + vertical
position| + 1% of |vertical position| + 0. 2 div + 7 mV] Vertical position 0 and vertical scale > 200 mV/div: ±[3% of |reading + vertical position| +
1% of |vertical position| + 0.2 div + 175 mV]
2 TBS1000B and TBS1000B-EDU Specications and Performance Verication
Table 1: Signal acquisition system characteristics (cont.)
Specications
Characteristic
Delta Volts Measurement Accuracy, Average Acquisition Mode
Analog Bandwidth
Analog Bandwidth, DC Coupled, Sample or Average
Analog Bandwidth, DC Coupled, Peak Detect, typical
Analog Bandwidth Selections
Description
Delta volts between any two averages of 16 waveforms acquired under the same setup and ambient conditions.
(3% of |reading| + 0.05 div)
Dened in Section 4.6 of IEEE std 1057. The difference between the upper and lower frequencies, at which the amplitude response, as seen in the data record, is 0.707 (-3 dB) of the response seen in the data record at the specied reference frequency. Species only the -3 dB point. It does not include the in-band response.
This is analog bandwidth when the instrument is DC coupled in sample or average mode. V/div values are accurate for probe attenuation settings of 1X. No probe should be installed for these measurements. System bandwidth is type tested to be equivalent to this specication with the provided probe in 10X mode. Use Section 4.6.1 of IEEE 1057, with the reference frequency of 1 kHz at an amplitude of 5 divisions, driven from a 50 source with external termination at the input BNC (25 effective source).
TBS1202B, TBS1202B-EDU: DC to 200 MHz for 5 mV/div through 5 V/div settings with bandwidth limit at full with temperature between 0° and 35 °C. DC to >160 MHz from 5 mV/div through 5 V/div settings with bandwidth limit at full for temperatures between 0° and 50 °C.< 5 mV/div settings are limited to 20 MHz bandwidth.
TBS1152B, TBS1152B-EDU: DC to 150 MHz for 5 mV/div through 5 V/div settings with bandwidth limit at full. < 5 mV/div settings are limited to 20 MHz bandwidth.
TBS1102B, TBS1102B-EDU: DC to 100 MHz for 5 mV/div through 5 V/div settings with the bandwidth limit at full. < 5 mV/div settings are limited to 20 MHz bandwidth.
TBS1072B, TBS1072B-EDU: DC to 70 MHz for 5 mV/div through 5 V/div settings with the bandwidth limit at full. < 5 mV/div settings are limited to 20 MHz bandwidth.
TBS1052B, TBS1052B-EDU: DC to 25 MHz for 5 mV/div through 5 V/div settings with bandwidth limit at full. < 5 mV/div settings are limited to 20 MHz bandwidth.
This is the analog bandwidth when the instrument is DC coupled. V/div values are accurate for probe attenuation settings of 1X. No probe should be installed for these measurements.
TBS1202B, TBS1202B-EDU, TBS1152B, TBS1152B-EDU, TBS1102B, TBS1102B-EDU: DC to 75 MHz for 5 mV/div through 5 V/div settings with the bandwidth limit at full. Settings less than 5 mV/div are limited to 20 MHz bandwidth.
TBS1072B, TBS1072B-EDU: DC to 50 MHz for 5 mV/div through 5 V/div settings with the bandwidth limit at full. Settings less than 5 mV/div are limited to 20 MHz bandwidth.
TBS1052B, TBS1052B-EDU: DC to 30 MHz for 5 mV/div through 5 V/div settings with the bandwidth limit at full. Settings less than 5 mV/div are limited to 20 MHz bandwidth.
20 MHz bandwidth limit ON/OFF
TBS1000B and TBS1000B-EDU Specications and Performance Verication 3
Specications
Table 1: Signal acquisition system characteristics (cont.)
Characteristic
Upper-Frequency Limit, 20 MHz Bandwidth Limited, typical
Lower- Frequency Limit, AC Coupled
Rise Time, typical
Peak Detect Mode Pulse Response
Vertical Position Ranges
Vertical Position Accuracy
Description
This is the upper frequency for Analog Bandwidth when the instrument has 20 MHz bandwidth limiting turned on.
20 MHz Bandwidth of all trigger paths are similarly limited, except the External Trigger, which is not
affected by BW Limit function. Each channel is separately limited, allowing different bandwidths on different channels of the same instrument.
This is the lower frequency for Analog Bandwidth when the instrument is AC-coupled
10 Hz. <1 Hz when 10X, passive probes are used.
Model
TBS1202B, TBS1202B -EDU TBS1152B, TBS1152B-EDU TBS1102B, TBS1102B-EDU TBS1072B, TBS1072B -EDU TBS1052B, TBS1052B -EDU Rise time is generally calculated from the following formula: Rise time in ns = 350 / Bandwidth in
MHz
This is the capability of the instrument to capture single event pulses using the Peak Detect Acquisition Mode.
The minimum single pulse widths for guaranteed 50% or greater amplitude capture are as follows:
Model
TBS1202B, TBS1202B-EDU, TBS1152B, TBS1152B-EDU, TBS1102B, TBS1102B-EDU, TBS1072B, TBS1072B -EDU
TBS1052B, TBS1052B -EDU
These are the ranges of the user-settable input offset voltage.
Volts/Div Setting
2 mV/div to 200 mV/div > 200 m V/div to 5 V/div
This is the accuracy of the nominal voltage level represented by the code at the vendor of the A-D converter's dynamic range.
Volts/Div Setting
2 mV/div to 200 mV/div ±(1% of |selected value| + 0.1 div + 5 mV) within the
> 200 mV/div to 5 V/div ±(1% of |selected v alue| + 0.1 div + 125 mV) within
Expected full bandwidth rise time
2.1 ns
2.4 ns
3.5 ns
5.0 ns
7.0 ns
Sec/Div Setting
50 s/div to 5 μS/div
Position Range
±1.8V ±45V
Position Accuracy
range ±1.8 V
the range ±45 V
Minimum Pulse Width
12 ns
13 ns
4 TBS1000B and TBS1000B-EDU Specications and Performance Verication
Table 1: Signal acquisition system characteristics (cont.)
Specications
Common Mode Rejection Ratio (CMRR), typical
Crosstalk (Channel Isolation)
With the same signal applied to each channel, CMRR is the ratio of the acquired signal amplitude to the amplitude of the MATH difference waveform, either (Channel 1 - Channel 2), (Channel 2 ­Channel 1)
Model
TBS1202B, TBS1202B-EDU, TBS1152B, TBS1152B-EDU, TBS1102B, TBS1102B-EDU
Section 4.11.1 of IEEE std. 1057. It is the ratio of the level of a signal input into one channel to that of the same signal present in another channel due to stray coupling.
Model
TBS1202B, TBS1202B-EDU
TBS1152B, TBS1152B-EDU
TBS1102B, TBS1102B-EDU
TBS1072B, TBS1072B-EDU
TBS1052B, TBS1052B-EDU
Common Mode Rejection Ratio
100:1 at 60 Hz, reducing to 10:1 with 50 MHz sine wave, with equal Volts/Div and Coupling settings on each channel.
Crosstalk
100:1 with a 100 MHz s ine wave and with equal V/div settings on each channel
100:1 with a 70 MHz sine wave and with equal V/div settings on each channel
100:1 with a 50 MHz sine wave and with equal V/div settings on each channel
100:1 with a 30 MHz sine wave and with equal V/div settings on each channel
100:1 with a 20 MHz sine wave and with equal V/div settings on each channel
Time Base System
Table2: Timebasesystem
Characteristic
Sample-Rate Range
Description
This is the range of real-time rates, expressed in samples/second, at which a digitizer samples signals at its inputs and stores the samples in memory to produce a record of time-sequential samples. (IEEE 1057, 2.2.1)
Model
TBS1202B, TBS1202B-EDU, TBS1152B, TBS1152B-EDU, TBS1102B, TBS1102B-EDU
TBS1072B, TBS1072B-EDU, TBS1052B, TBS1052B-EDU
Sample-rate range
5 S/s to 2000 MS/s. Refer to the table for a tabular listing (See Table 3 on page 7.)
5 S/s to 1000 MS/s Refer to the table for a tabular listing (See Table 3 on page 7.)
TBS1000B and TBS1000B-EDU Specications and Performance Verication 5
Specications
Table 2: Time base system (cont.)
Characteristic
Interpolation
Record Length
Seconds/Division Range
Long-Term Sample Rate and Horizontal Position Time Accuracy
Horizontal Position Time Range
Zoom
Delta Time Measurement Accuracy
Description
(Sin x)/x interpolationWaveform Waveform interpolation is activated for sweep speeds of 100 ns/div and faster.
This is the total number of samples contained in a single acquired waveform record (Memory Length in IEEE 1057.2.2.1).
2,500 samples per record.
Sec/Div Variable function is not available for this product.
Model Range
TBS1202B, TBS1202B-EDU, TBS1152B, TBS1152B-EDU, TBS1102B, TBS1102B-EDU
TBS1072B, TBS1072B-EDU, TBS1052B, TBS1052B-EDU
This is the maximum, total, long-term error in sample-rate or horizontal position time accuracy, expressed in parts per million.
±50 ppm over any 1 ms interval.
Horizontal scale setting Horizontal position time range
5ns/divto10ns/div 25 ns/div to 100 μs/div 250 μs/divto10s/div 25 s/div to 5 0 s/div The user controls the time from the trigger to the center graticule on the display with the
Horizontal Position knob. The resolution of the Horizontal Position time is 1/25 of a horizontal division. The zoom function enables a user to select a part of the display to be magnied. Both the
original waveform and the zoomed waveform are displayed. The user chooses the waveform with the Multipurpose knob.
This is the accuracy of delta time measurements made on any single waveform. The specication is related to the long-term sampling rate.
The following limits are given for signals having an amplitude 5 divisions, a slew rate at the measurement points of 2.0 divisions/ns, and acquired 10 mV/div.
Condition
Single shot, sample mode, full bandwidth selected
> 16 averages, full bandwidth selected
The Sample Interval is the time between the samples in the waveform record.
2.5 ns/div to 50 s/div in 1–2.5–5 sequence Refer to the table for a tabular listing (See Table 3 on page 7.)
5 ns/div to 50 s/div in 1–2.5–5 sequence Refer to the table for a tabular listing (See Table 3 on page 7.)
–4 div * s/div to 20 ms –4 div * s/div to 50 ms –4 div * s/div to 50 s –4 div * s/div to 250 s
Time Measurement Accuracy
±(1 Sample Internal + 100 ppm * |reading| + 0.6 ns)
±(1 Sample Internal + 100 ppm * |reading| + 0.4 ns)
6 TBS1000B and TBS1000B-EDU Specications and Performance Verication
Table 2: Time base system (cont.)
Specications
Characteristic
Time Measurement Functions
Miscellaneous Measurement
Description
Frequency, Period , Rise, Fall, Pwidth, Nwidth, Pduty, Nduty, DelayRR, DelayRF, DelayFR, DelayFF, Burst width, Phase.
Area, Cycle Area, Rising edge count, Falling edge count, Positive pulse count, Negative pulse count
Functions
The following table shows conditions for each Sec/Div. When possible, the input signal is over-sampled. At the fastest Sec/Div settings, the data is interpolated so that the waveform record length stays constant.
Table 3: Table of time base characteristics
Sampling rate [Sampling rate with interpolation]
1GS/smax
1
2 GS/s max
2
1 G S/s [100 GS/s] 2 GS/s [100 GS/s] 1 GS/s [50 GS/s] 2 GS/s [50 GS/s] 1 GS/s [25 GS/s] 2 GS/s [25 GS/s] 1 GS/s [10 GS/s] 2 GS/s [10 GS/s] 1GS/s[5GS/s] 2GS/s[5GS/s] 1 GS/s [2.5 GS/s] 2 GS/s [2.5 GS/s] 1GS/s 500 MS/s 250 MS/s 100 MS/s 50 MS/s 25 MS/s 10 MS/s 5MS/s
2.5 MS/s 1MS/s 500 KS/s 250 KS/s 100 KS/s 50 KS/s 25 KS/s 10 KS/s 5KS/s
2.5 KS/s 1KS/s 500 S/s
Horizontal pixel interval in Display
30 ps 60 ps 120 ps 300 ps 600 ps
1.2 ns 3ns 6ns 12 ns 30 ns 60 ns 120 ns 300 ns 600 ns
1.2 μs 3 μs 6 μs 12 μs 30 μs 60 μs 120 μs 300 μs 600 μs
1.2 ms 3ms 6ms
Sec/Div Mode
2
2.5 ns 5ns 10 ns 25 ns 50 ns 100 ns 250 ns 500 ps 1 μs
2.5 μs 5 μs 10 μs 25 μs 50 μs 100 μs 250 μs 500 μs 1ms
2.5 ms 5ms 10 ms 25 ms 50 ms 100 ms 250 ms 500 ms
FISO (interpolated) FISO (interpolated) FISO (interpolated) FISO (interpolated) FISO (interpolated) FISO (interpolated) FISO FISO FISO FISO FISO FISO FISO FISO FISO S.P. S.P. S.P. S.P. S.P. S.P. S.P. S.P. S.P. (Scan Mode) S.P. (Scan Mode) S.P. (Scan Mode)
Sample interval in waveform record
10 ps 20 ps 40 ps 100 ps 200 ps 400 ps 1ns 2ns 4ns 10 ns 20 ns 40 ns 100 ns 200 ns 400 ns 1 μs 2 μs 4 μs 10 μs 20 μs 40 μs 100 μs 200 μs 400 μs 1ms 2ms
TBS1000B and TBS1000B-EDU Specications and Performance Verication 7
Specications
Table 3: Table of time base characteristics (cont.)
Sample interval in waveform
Sec/Div Mode
1s
2.5 s 5s 10 s 25 s 50 s
1
TBS107
2
TBS1102B, TBS1102B-EDU, TBS1152B, TBS1152B-EDU, TBS1202B, TBS1202B-EDU
S.P. (S can Mode) S.P. (S can Mode) S.P. (S can Mode) S.P. (S can Mode) S.P. (S can Mode) S.P. (S can Mode)
2B, TBS1072B-EDU, TBS1052B, TBS1052B-EDU
record
4ms 10 ms 20 ms 4ms 100 ms 200 ms
Sampling rate [Sampling rate with interpolation]
1GS/smax
250 S/s 100 S/s 50 S/s 25 S/s 10 S/s 5S/s
Horizontal
1
2 GS/s max
2
pixel interval in Display
12 ms 30 ms 60 ms 120 ms 300 ms 600 ms
8 TBS1000B and TBS1000B-EDU Specications and Performance Verication
Triggering System
Table 4: Triggering system
Characteristic Description
Trigger Types Edge, Video, Pulse Width
Selection
Horizonta Position
Trigger Holdoff Range
External Trigger Input Impedan
External Trigger Maximu Voltage
Line Trigger Characteristics
Edg
l Trigger
ce
m Input
e Trigger Trigger Modes Auto, Normal
Trigger Slope
Specications
Channel 1,
External, External/5, AC LineTrigger Source
Channel 2 External/5 selection attenuates the external signal by 5. When Bandwi
dth Limit is selected for c hannels, the bandwidth of that channel’s trigger path will
also be limited. The bandwidth of the External Trigger path is not affected by the bandwidth limit. The trigge
500 ns min The abili
r position is set by the Horizontal Position knob.
imum to 10 s maximum
ty to set large values of Holdoff is limited by the difculty in adjusting the Holdoff at seconds/Div settings less than 100 ms/Div. This is because Holdoff cannot be set in Scan Mode, which begins at 100 ms/div when Trigger Mode is AUTO. By adjusting Trigger Mode to NORMAL, the Scan
1M±2%i
300 V
Mode operation is turned off, and Holdoff can be adjusted at larger seconds/Div settings.
nparallelwith20pF±3pF
, Installation Category II; derate at 20 dB/decade above 100 kHz to 13 V peak AC at
RMS
3 MHz and above Based on sinusoidal or DC input signal. The maximum viewable signal while DC coupled is ±50 V
offset ±5 V/div at 4 divisions, or 70 V. AC coupling allows measuring signals on a DC level up
V. For nonsinusoidal waveforms, peak value must be less than 450 V. Excursions above
to 300 300 V should be less than 100 ms duration and the duty factor is limited to < 44%. RMS signal level must be limited to 300 V. If these values are exceeded, damage to the instrument may result.
Line Trigger mode provides a source to synchronize the trigger with the AC line input.
t Amplitude requirements: 85 V
Inpu
- 265 VAC.
AC
Input Frequency requirements: 45 Hz - 440 Hz.
AC, DC, Noise Reject, High Frequency Reject, Low Frequency RejectTrigger Coupling The External Trigger path does not have a DC blocking capacitor ahead of the trigger input
rcuit. The roll off associated with AC coupling happens after the input circuit. When attempting
ci to trigger on an AC signal that has a DC offset, use care to avoid overloading the input of the External Trigger circuit. For signals that have a large DC offset, using Channel 1 or Channel 2
ith AC coupling is preferred.
w Rising Edge, Falling Edge
TBS1000B and TBS1000B-EDU Specications and Performance Verication 9
Specications
Table 4: Triggering system (cont.)
Characteristic Description
Sensitivity, Edge-Type Trigger, DC Coupled
Measurement Style A: The minimum signal levels for achieving stable frequency indication on the Trigger Frequency Counter within 1% of correct indication.
Measurement Style B: Section 4 10.2 in IEEE Std. #1057. The minimum signal levels required for stable edge triggering of an acquisition when the trigger Source is DC coupled.
Trigger Source Sensitivity
(Measurement style A), typical
Channel Inputs
Ext
Ext/5
Trigger Frequency Readout typically stabilizes at 50% more signal than generates a stable visual display.
All products
TBS1052B, TBS1052B­EDU
TBS1072B, TBS1072B­EDU
TBS1102B, TBS1102B­EDU
TBS1152B, TBS1152B­EDU
TBS1202B, TBS1202B­EDU
1.5 div from DC to 10 MHz ( > 2 mV/div)
4 div from DC to 10 MHz (2 mV/Div)
3 div between 10 MHz and 50 MHz
3 div between 10 MHz and 70 MHz
3 div between 10 MHz and 100 MHz
3 div between 10 MHz and 150 MHz
3 div between 10 MHz and 200 MHz
300 mV from DC to 100 MHz
500 mV from 100 MHz to 200 MHz
(TBS1202B, TBS1202B-EDU, TBS1152B, TBS1152B-EDU )
1.5 V from DC to 100 MHz
2.5 V from 100 MHz to 200 MHz
(TBS1202B, TBS1202B-EDU, TBS1152B, TBS1152B-EDU )
Sensitivity (Measurement style B)
0.8 div from DC to 10 MHz >2mV/div)
2.5 div from DC to 10 MHz (2 mV/Div)
1.5 div between 10 MHz and 50 MHz
1.5 div between 10 MHz and 70 MHz
1.5 div between 10 MHz and 100 MHz
1.5 div from 10 MHz and 100 MHz
2.0 div above 100 MHz to 150 MHz
1.5 div from 10 MHz and 100 MHz
2.0 div above 100 MHz to 200 MHz
200 mV from DC to 100 MHz
350 mV from 100 MHz to 200 MHz
(TBS1202B, TBS1202B-EDU, TBS1152B, TBS1152B-EDU )
1 V from DC to 100 MHz
1.75 V from 100 MHz to 200 MHz
(TBS1202B, TBS1202B-EDU, TBS1152B, TBS1152B-EDU )
10 TBS1000B and TBS1000B-EDU Specications and Performance Verication
Table 4: Triggering system (cont.)
Characteristic Description
Sensitivity, Edge-Type Trigger, non-DC Coupled, typical
Lowest Frequency for Successful Operation of “Set Level to 50%” Function, typical
Trigger Level Ranges, typical
Trigger Level Accuracy, DC Coupled, typical
Video Trigger
Default Settings for Video Trigger
Video Trigger Source Selection
Video Trigger Polarity Selection
Video Sync Selection
Formats and Field Rates
Trigger Source Sensitivity
AC Same as DC Coupled limits for frequencies 50 H z and
Noise Rej
HF Rej LF Ref Same as DC Coupled limits for frequencies above
Since AC coupling is not done in the front end, use of a 10 M probe does not affect the low frequency corner.
This is the typical lowest frequency for which the “Set Level to 50%” function will successfully determine the 50% point of the trigger signal.
50 Hz. Using a 10M probe will not affect the operation of this function.
Input Channel ±8 divisions from center screen
Ext ±1.6 V Ext/5: The settable resolution for Trigger Level is 0.02 division for an input channel source, 4 mV for Ext
source, and 20 mV for Ext/5 source.
This is the amount of deviation allowed between the level on the waveform at which triggering occurs and the level selected for DC-coupled triggering signals. A sine wave with 20 ns rise time corresponds to about 18 MHz.
±(0.2 div + 5 mV) for signals within ±4 divisions from the center screen, having rise and fall times of 20 ns.
Ext: ±(6% of setting + 40 mV) for signals less than ±800 mV Ext/5: ±(6% of setting + 200 mV) for signals less than ±4 V
Trigger Mode: Auto Trigger Coupling: AC Same as Source Selections listed above except Line Trigger. Line Trigger source is meaningless
in this mode. Normal (Negative going Sync Signal), Invert (Positive going Sync Signal)
Line, Line #, Odd Field, Even Field, Field: PAL/SECAM, NTSC formats
Fieldrates:50Hzto60Hz.Video Trigger Line rates: 15 kHz to 20 kHz (NTSC, PAL, SECAM)
Specications
above Effective in Sample or Average Mode, > 10 mV/div to
5 V/div. Reduces DC Coupled trigger sensitivity by 2X. Same as DC Coupled limits from DC to 7 kHz.
300 kHz.
±8 V
TBS1000B and TBS1000B-EDU Specications and Performance Verication 11
Specications
Table 4: Triggering system (cont.)
Characteristic Description
Pulse-Width Trigger
Video Trigger Sensitivity, typical
Pulse-Width Trigger Modes
Pulse Width Trigger Edge
Pulse Width Range
Pulse Width Resolution
Equal Guardband
Not Equal Guardband
Pulse-Width Trigger Point
This is the minimum peak-to-peak video s ignal required for stable Video-Type triggering. A 2 division composite video signal will have 0 .6 division sync tip.
Source
Input Channels 2 divisions of composite video Ext Ext/5 2 V of composite video
< (Less than), > (Greater than), = (Equal), (Not equal)
Falling edge for positive polarity pulse. Rising edge for negative polarity pulse.
33 ns width 10 seconds
16.5 ns or 1 part per thousand, whichever is larger
t > 330 ns: ±5% < guardband < ±(5.1% + 16.5 ns) t 330 ns: guardband = ±16.5 ns. All pulses, even from the most stable sources, have some amount of jitter. To avoid disqualifying
pulses that are intended to qualify but are not absolutely correct values, Tektronix provides an arbitrary guardband. Any measured pulse width within the guardband will qualify. If you are looking for pulse width differences that are smaller than the guardband width, offsetting the center should allow discriminating differences down to the guardband accuracy.
330 ns < 1: ±5% guardband < ±(5.1% + 16.5 ns) 165 ns < 1 < 330 ns: guardband = -16.5 ns/+33 ns t 165 ns: guardband = ± 16.5 ns All pulses, even from the most stable sources, have some amount of jitter. To avoid disqualifying
pulses that are intended to qualify but are not absolutely correct values, Tektronix provides an arbitrary guardband. Any measured pulse width outside the guardband will qualify. If you are looking for pulse width differences that are smaller than the guardband width, offsetting the center should allow discriminating differences down to the guardband accuracy. Not equal has slightly better ability to deal w ith small pulse widths than equal. The accuracy is not better.
Equal: The oscilloscope triggers when the trailing edge of the pulse crosses the trigger level. Not Equal: If the pulse is narrower than the specied width, the trigger point is the trailing edge.
Otherwise, the oscilloscope triggers when a pulse continues longer than the time specied as the Pulse Width.
Less than: The trigger point is the trailing edge. Greater than (also called the time out trigger): The oscilloscope triggers when a pulse continues
longer than the time specied as the Pulse Width.
Typical sensitivity
400 mV of composite video
12 TBS1000B and TBS1000B-EDU Specications and Performance Verication
Display Specications
Table 5: Display specications
Characteristic Description
Display Type
Display Res
Brightness, typical
Contrast Ratio and Control, typical
olution
Specications
This is the description of the display, including its nominal screen size.
17.0 cm (width) * 11.1 cm (height) * 0.8 cm (depth), 17.78 cm diagonal (7”), WVGA(800(H)X480(V)), active TFT c background.
This is the number of individually addressable pixels
800 horizo The video
This is th
300 cd/m The brightness can be controlled by the PWM signal; a menu for this is provided. Available black room contrast ratio, full black to full white. 400 minimum, 500 typical.
olor liquid crystal display (LCD) with color characters/waveforms on a black
ntal by 480 vertical pixels display contains both the character and waveform displays.
e light output of the back light.
2
, typical. 250 cd/m2min.
Interfaces and Output Ports Specications
6: Interfaces and output ports specications
Table
Characteristic Description
USB Device USB 2.0 High Speed device. 480 Mb/second maximum. Supports PICTBRIDGE compatibility and
provides USB-TMC communications with Tektronix extensions.
dard
Stan
Host
USB
USB Host Current Provides full 0.5 A of 5 V.
PIB Interface
G
robe Compensator,
P Output Voltage and Frequency, typical
2.0 Full Speed host. 12 Mb/sec maximum. Supports USB Mass Storage Class. Bulk Only
USB Subclass only. Provides full 0.5 A of 5 V.
Standard
andard
St
PIB access via TEK-USB-488 accessory.
G
he Probe Compensator output voltage is in peak-to-peak Volts and frequency is in Hertz.
T
Output voltage: 5.0 V ±10% into 1 Mload. Frequency: 1 kHz
TBS1000B and TBS1000B-EDU Specications and Performance Verication 13
Specications
Data Handling Characteristics
Table 7: Data handling characteristics
Characteristic Description
Retention of Front Panel Settin
Stored Wave and Multiple Front Panel Settings
gs
forms
Front panel settings are stored periodically in memory. The settings are not lost when the instrument is turned off or if there is a power failure.
Two Channel or B. One, both, or neither of A or B waveform memories can be displayed. Ten user setups of the current instrument settings can be saved and restored from nonvolatile memory. Additional storage is availabl
e when an appropriate mass storage device is connected via USB.
Power Distribution System
Table 8: Power distribution system
Characteristic Description
Power Consumption Source Voltage Full Range: 100 to 240 V Source Frequency 360 Hz to 440 Hz from 100 VACto 120 VAC.
Fuse Rating
Less than 30 W at 85 to 275 V
45 Hz to
3.15 A
66 Hz from 100 V
mps, T rating, 250 V; IEC and UL approved.
1, Channel 2, or Math waveforms can be stored in nonvolatile waveform memory A
input.
AC
± 10%, Installation Category II (Covers range of 90 to 264 V
ACRMS
to 240 VAC.
AC
AC
Mechanical Characteristics
Table 9: Mechanical characteristics
Characteristic Description
Weight
Size
Cooling Method Convection cooled
Requirements that follow are nominal:
kg (4.4 lbs), stand-alone instrument
2.0
2.2 kg (4.9 lbs), with accessories
3.6 kg (8 lbs), when packaged for domestic shipment Height Width Depth
158 mm (6.22 in)
326.3 mm (12.85 in)
124.1 mm (4.88 in)
14 TBS1000B and TBS1000B-EDU Specications and Performance Verication
Environmental Performance
Table 10: Environmental performance
Characteristic Description
Temperature
Humidity
Altitude
Operating 0° C to +50° C (32 °F to 122 °F) Nonoperating
Operating a Nonoperating
Operatin Nonoperating
nd
g
Data Logging System Characteristics
Specications
–40° C to +71° C (–40 °F to 159.8 °F), with 5° C/minute maximum gradient
5% to 90% rel 5% to 45% RH above +40° C up to +50° C, noncondensing, and as
limited by a Maximum Wet-Bulb Temperature of +37° C (derates relative h
Up to 3,00 Up to 12,0
ative humidity (% RH) at up to +39° C
umidity to 45 % RH at +50° C)
0 meters (9,842 feet) 00 meters (39,370 feet).
NOTE. T
the trigger conditions to use, you can use the data logging menu to set up the oscilloscope so that it will save all of the triggered waveform to a USB memory device, within a time duration that you have set.
Table
Characteristic Description
Dura
Sou
Select Folder The le folder where you save the waveform data.
his software feature directs the oscilloscope to automatically collect data over a period of time. After you congure
11: Data logging system characteristics
tion
rce
ime period.
The t
0.5 hour, 1 hour, 1.5 hour, 2 hour, 2.5 hour, 3 hour, 3.5 hour, 4 hour, 4.5 hour, 5 hour, 5.5 hour, 6 hour, 6.5 hour, 7 hour, 7.5 hour, 8 hour, 9 hour, 10 hour, 11 hour, 12 hour, 13 hour, 14 hour, 15
, 16 hour, 17 hour, 18 hour, 19 hour, 20 hour, 21 hour, 22 hour, 23 hour, 24 hour, Innite
hour
signal source which you want to save the waveform.
The Channel 1, Channel 2, Math
You can create the new folder or change the existing folder as the folder where you want to save
e waveform data.
th
TBS1000B and TBS1000B-EDU Specications and Performance Verication 15
Specications
Limit Testing System Characteristics
NOTE. This sof
or fail results by judging whether the input signal is within the bounds of the template.
tware feature directs the oscilloscope to monitor an active input signal against a template and to output pass
Table 12: Limit testing system characteristics
Characteri
Source
Compare Re
Run/Stop To enable or disable the limit testing function.
Templa t
Source The location of the signal source that is used to create the limit test template.
Vertical Limit The vertical limit in vertical divisions.
Horizontal Limit The horizontal limit in horizontal divisions.
Dest
Disp
Act
Stop After Denes the conditions that will cause the oscilloscope to end limit testing.
stic
f Channel
e Setup
ination Ref Channel
lay Template
iononViolation
Descriptio
The signal source which you want to do the limit testing.
Channel 1, C
The refere
RefA, RefB, and DualRef. The limit testing system will compare the source signal with this template.
Run, Stop Use this
that you dene as the boundary to compare with the input source signal. You can create the template from internal or external waveforms with specic horizontal and vertical tolerances.
Single
0~100
0~500
The l
RefA, RefB.
Disp
On, Off.
Denes the actions the oscilloscope will take after a violation is detected. Save Image: The oscilloscope will automatically save a screen image when a violation is
tected.
de Save Waveform: The oscilloscope will automatically save a digital copy of the source waveform
when a violation is detected.
anual: Lets you stop the test by toggling the “Run/stop” choice.
M Waveforms: Lets you set the numbers of waveforms to test before stopping limit testing. Violations: Lets you set the numbers of violations to detect before stopping limit testing.
lapsed time: Lets you set the elapsed test time in seconds to pass before stopping limit testing.
E
n
hannel 2, Math
nce channel number where the template is saved.
.
menu item to set up a limit test waveform template. The template is the mask signal
Ref(CH1, CH2, MATH) Dual Ref(CH1, CH2, MATH)
0mdiv
mdiv.
ocation of the reference memory location that is used to store the limit test template.
lays or does not display a stored test template.
16 TBS1000B and TBS1000B-EDU Specications and Performance Verication
Performance Ver
ication
Performance V
This chapter contains performance verication procedures for the specications marked with the check m ark. The following equipment, or a suitable equivalent, is required to complete these procedures.
erication
Required Equipment
Table 13: Performance verication
Description Minimum requirements Examples
DC Voltage Source 17.5 mV to 7 V, ±0.5% accuracy Leveled Sine Wave Generator 50 kHz and 200 MHz, ±3% amplitude
Time Mark Generator
50BNC Cable BNC male to BNC male, 1 m (36 in) long 50BNC Cable BNC male to BNC male, 25 cm (10 in)
50Feedthrough Termination BNC male and female connectors Dual Banana to BNC Adapter Banana plugs to BNC female BNC T Adapter BNC male to dual BNC female connectors Splitter, Power Frequency range: DC to 4 GHz.
Adapter (four required) Male N-to-female BNC Adapter Leads, 3 Black
Leads, 2 Red
accuracy 10 ms period, ±10 ppm accuracy
long
Tracking: >2.0%
Female N-to-male BNC Stacking Banana Plug Patch Cord,
45 cm (18 in) long Stacking Banana Plug Patch Cord,
45 cm (18 in) long
Wavetek 9100 Universal Calibration System with Oscilloscope Calibration Module (Option 250)
Fluke 5500A Multi-product C alibrator with Oscilloscope Calibration Option (Option 5500A-SC)
Tektronix part number 012-0482-XX Tektronix part number 012-0208-XX
Tektronix part number 011-0049-XX Tektronix part number 103-0090-XX Tektronix part number 103-0030-XX Tektronix part number 015-0565-XX
Tektronix part number 103-045-XX Tektronix part number 103-0058-XX Pomona #B-18-0
Pomona #B-18-2
TBS1000B and TBS1000B-EDU Specications and Performance Verication 17
Performance Ver
ication
Test Record
Table 14: Test
record
Instrument Serial Number: Temperature: Date of Calib
ration:
Instrument performance t
Channel 1 DC Gain Accuracy
est
Minimum Incoming Outgoing Maximum
5mV/div 200 mV/div 2V/div
Channel 2 DC Gain Accuracy
5mV/div 200 mV/di
v
2V/div Channel Channel Sample Channe Chann Exte Chan
1 Bandwidth 2 Bandwidth
Rate and Delay Time Accuracy
l 1 Edge Trigger S ensitivity
el 2 Edge Trigger S ensitivity
rnal Edge Trigger Sensitivity
nel 1 Vertical Position Accuracy,
Minimum margin Channel 2 Vertical Position Accuracy,
Minimum margin
1
The bandwidth test does not have a high limit.
2
The limits vary by model. Check the procedure for the correct limits.
Certicate Number: RH %: Technician:
33.6 mV 36.4 mV
1.358 V 1.442 V
13.58 V 14.42 V
33.6 mV 36.4 mV
1.358 V 1.442 V
13.58 V 14.42 V
1
2.12 V
2.12 V
— —
1
-2 divs +2 divs
2
Stable Stabl Stab 0
0
trigger
e trigger
le trigger
— — — —
2
2
Performance Verication Procedures
Before beginning these procedures, two conditions must be met:
The oscilloscope must have been operating continuously for twenty minutes within the operating temperature range specied in the Environmental Performance table. (See Table 10.)
You must perform the Self Calibration operation described below. If the ambient temperature changes by more than 5 °C, you m ust perform the Self Calibration operation again.
The time required to complete the entire procedure is approximately one hour.
WARNING. Some procedures use hazardous voltages. To prevent electrical shock, always set voltage source outputs
to 0 V before making or changing any interconnections.
18 TBS1000B and TBS1000B-EDU Specications and Performance Verication
Performance Ver
ication
Self Test
This internal procedure is automatically performed every time the oscilloscope is powered on. No test equipment or hookups are required. Verify that no error messages are displayed before continuing with this procedure.
Self Calibration
The self cali
bration routine lets you quickly optimize the oscilloscope signal path for maximum measurement accuracy. You
can run the routine at any time, but you should always run the routine if the ambient temperature changes by 5 °C or more.
1. Disconnect all probes and cables from the channel input connectors (channels 1 and 2).
2. Push the Utility button and select the Do Self Cal option to start the routine. The routine takes approximately one
minute to complete.
3. Verify that self calibration passed.
Check DC G
ain Accuracy
This test checks the DC gain accuracy of all input channels.
1. S et the DC voltage source output level to 0V.
2. Set up the oscilloscope using the following table:
Push menu button Select menu option Select setting
Default Setup
Channel 1
——
Probe 1X
Acquire Average 16
Measure
Source Channel under test Measurements Mean
3. Connect the oscilloscope channel under test to th e DC voltage source as shown in the following gure:
4. For each vertical scale (volts/division) setting in the following table, perform the following steps:
a. Set the DC voltage source output level to the positive v oltage listed and then record the mean measurement as V
b. Reverse the polarity of the DC voltage source and record the mean measurement as V
c. Calculate V
diff=Vpos-Vneg
and compare V
to the accuracy limits in the following table:
diff
neg
.
.
pos
TBS1000B and TBS1000B-EDU Specications and Performance Verication 19
Performance Ver
ication
Vertical Scale (volts/div) setting
5mV/div 200 mV/div 2V/div
5. Set DC voltage source output level to 0V.
6. Disconnect the test setup.
7. Repeat steps 1 through 6 for all input channels.
Check Band
This test checks the bandwidth of all input channels.
1. Set up the oscilloscope using the following table:
Push menu button Select menu option Select setting
Default Setup Channel 1 Acquire Average 16
Trig Menu
Measure
width
DC voltage source output levels Accuracy limits for V
+17.5 mV, -17. +700 mV, -700 m +7.00 V, -7.0
——
Probe 1X
Coupling Source Channel under test Measurements Peak-Peak
5mV
0V
33.6 mV to 36.4
V
1.358 V to 1.44
13.58 V to 14.
Noise Reject
diff
mV
2V
42 V
2. Connect the oscilloscope channel under test to the leveled sine wave generator as shown in the following gure:
3. Set the oscilloscope Vertical Scale (volts/division) to 500 mV/div.
4. Set the oscilloscope Horizontal Scale (seconds/division) to 10 μs/div.
5. Set the leveled sine wave generator frequency to 50 kHz.
6. Set the leveled sine wave generator output level so the peak-to-peak measurement is between 2.98 V and 3.02 V.
20 TBS1000B and TBS1000B-EDU Specications and Performance Verication
7. Set the leveled sine wave generator frequency to:
200 MHz if you are checking a TBS1202B or TBS1202B-EDU
150 MHz if you are checking a TBS1152B or TBS1152B-EDU
100 MHz if you are checking a TBS1102B or TBS1102B-EDU
70 MHz if you are checking a TBS1072B or TBS1072B-EDU
50 MHz if you are checking a TBS1052B or TBS1052B-EDU
8. Set the oscilloscope Horizontal Scale (seconds/division) to 10 ns/div.
9. Check that the peak-to-peak measurement is 2.12 V.
10. Disconnect the test setup.
11. Repeat steps 1 through 10 for all input channels.
Check Sample Rate Accuracy and Delay Time Accuracy
This test checks the time base accuracy.
1. Set up the oscilloscope using the following table:
Performance Ver
ication
Push menu button Select menu option Select setting
Default S etup Channel 1
2. Connect the oscilloscope to the time mark generator as shown in the following gure:
3. Set the time mark generator period to 10 ms.
4. Set the oscilloscope Vertical Scale (volts/division) to 500 mV/div.
5. Set the oscilloscope Main Horizontal Scale (seconds/division) to 1ms/div.
6. Push the Trigger Level knob to activate the Set To 50% feature.
——
Probe 1X
7. Use the Vertical Position control to center the test signal on screen.
8. Use the Horizontal Position control to set the position to 10.00 ms.
9. Set the oscilloscope Horizontal Scale (seconds/division) to 250 ns/div.
TBS1000B and TBS1000B-EDU Specications and Performance Verication 21
Performance Ver
10. Check that the rising edge of the marker crosses the center horizontal graticule line within ±2 divisions of the vertical
center graticu
ication
le line, as shown in the following gure:
NOTE. One division of displacement from graticule center corresponds to a 25 ppm time base error.
11. Disconnect the test setup.
Check E
This test checks the edge trigger sensitivity for all input channels.
1. Set up the oscilloscope using the following table:
Push menu button Select menu option Select setting
Default Setup Channel 1 Trig Menu Mode Normal
Acquire
Measure
dge Trigger Sensitivity
——
Probe 1X
Sample Source Channel under test Measurements Peak-Peak
22 TBS1000B and TBS1000B-EDU Specications and Performance Verication
Performance Ver
2. Connect the oscilloscope channel under test to the leveled sine wave generator as shown in the following gure:
3. Set the oscilloscope Vertical Scale (volts/division) to 500 mV/div.
4. Set the oscilloscope Horizontal Scale (seconds/division) to 25 ns/div.
5. Set the leveled sine wave generator frequency to 10 MHz.
ication
6. Set the leveled sine wave generator output level to approximately 500 mV
so that the measured amplitude is
p-p
approximately 500 mV. (The measured amplitude can uctuate around 500 mV.)
7. Push the Trigger Level knob to activate the Set To 50%. Rotate the Trigger Level knob to adjust the trigger level
as necessary and then check that triggering is stable.
8. Set the leveled sine wave generator frequency to:
200 MHz if you are checking a TBS1202B or TBS1202B-EDU
150 MHz if you are checking a TBS1152B or TBS1152B-EDU
100 MHz if you are checking a TBS1102B or TBS1102B-EDU
70 MHz if you are checking a TBS1072B or TBS1072B-EDU
50 MHz if you are checking a TBS1052B or TBS1052B-EDU
9. Set the oscilloscope Horizontal Scale (seconds/division) to 5ns/div.
10. Set the leveled sine wave generator output level to approximately 750 mV
approximately 750 mV. (The measured ampl
itude can uctuate around 750 mV.)
so that the measured amplitude is
p-p
11. Push the Trigger Level knob to activ a te the Set To 50% feature. Rotate the Trigger Level knob to adjust the trigger
level as necessary and then check that triggering is stable.
12. For the TBS1152B, TBS1152B-EDU, TBS1202B, and TBS1202B–EDU models, set the frequency to 150 MHz, and increase the amplitude to 1 V
. Verify stable triggering.
p-p
13. Set the oscilloscope Horizontal Scale (seconds/division) to 2.5 ns/div.
14. Change the oscilloscope setup using the following table:
Push menu button Select menu option Select setting
Trig Menu
Slope
Falling
15. Push the Trigger Level knob to activate the Set To 50% feature. Rotate the Trigger Level knob to adjust the trigger level as necessary and then check that triggering is stable.
TBS1000B and TBS1000B-EDU Specications and Performance Verication 23
Performance Ver
16. Disconnect the test setup.
17. Repeat steps 1 through 16 for all input channels.
ication
Check Externa
l Edge Trigger Sensitivity
This test checks the edge trigger sensitivity for the external trigger.
1. Set up the oscilloscope using the following table:
Push menu button Select menu option Select setting
Default Setup Channel 1
Trig Menu
——
Probe 1X Source
Ext
Mode Normal
Acquire
Measure
Sample Source CH1
Measurements Peak-Peak
2. Connect the oscilloscope to the leveled sine wave generator as shown in the following gure, using channel 1 and Ext Trig.
3. Set the oscilloscope Vertical Scale (volts/division) to 100 mV/div.
4. Set the oscilloscope Horizontal Scale (seconds/division) to 25 ns/d iv .
5. Set the leveled sine wave generator frequency to 10 MHz.
6. Set the sine wave generator output level to approximately 300 mV
into the power splitter. This is about 200 mV
p-p
p-p
on channel 1 of the oscilloscope.
The Ext Trig input will also be receiving approximately 200 mV
. Small deviations from the nominal 200 mV
p-p
p-p
oscilloscope display are acceptable.
24 TBS1000B and TBS1000B-EDU Specications and Performance Verication
Performance Ver
7. Set the leveled sine wave generator frequency to:
200 MHz if you are checking a TBS1202B or TBS1202B-EDU
150 MHz if you are checking a TBS1152B or TBS1152B-EDU
100 MHz if you are checking a TBS1102B or TBS1102B-EDU
70 MHz if you are checking a TBS1072B or TBS1072B-EDU
50 MHz if you are checking a TBS1052B or TBS1052B-EDU
8. Set the oscilloscope Horizontal Scale (seconds/division) to 5ns/div.
9. Push the Trigger Level knob to activate the Set To 50% feature. Rotate the Trigger Level knob to adjust the trigger
level as nec
essary and then check that triggering is stable.
ication
10. Set the osci
11. Push the Tr
level as necessary and then check that triggering is stable.
12. Change the oscilloscope setup using the following table:
Push menu button Select menu option Select setting
Trig Menu
13. Push the Trigger Level knob to activate the Set To 50% feature. Rotate the Trigger Level knob to adjust the trigger
level as
14. Disconn
lloscope Horizontal Scale (seconds/division) to 2.5 ns/div.
igger Level knob to activate the Set To 50% feature. Rotate the Trigger Level knob to adjust the trigger
Slope
necessary and then check that triggering is stable.
ect the test setup.
Falling
Check Vertical Position Accuracy
The results of this test and the DC Gain Accuracy test together dene the DC Measurement Accuracy of the oscilloscope. The DC Measurement Accuracy specication encompasses two different ranges of operation over two different attenuator settings.
DC Gain Accuracy: Identies errors, mostly from the A/D converter, when the vertical position (known as offset in these oscilloscopes) is set to 0 divisions (or a grounded input will show screen center)
Vertical Position Accuracy: Identies errors, mostly from the position c ontro l, made when the vertical position is set to a non-zero value
The two attenuator settings operate identically, so verication of the attenuation range from -1.8 V to 1.8 V also veries the attenuation range of -45 V to 45 V.
TBS1000B and TBS1000B-EDU Specications and Performance Verication 25
Performance Ver
1. Set up the oscilloscope as shown in the following table:
Push menu button Select menu option Select setting
Default Setup
Channels 1, 2, Channels 1, 2, Volts/Div 50 mV/div
Trig Menu
Acquire
Measure
1
The test operates without a trigger. To maintain uniformity and to avoid false triggering on noise, the Ext trigge
2. Make a spreadsheet approximately as shown in the example in Appendix A. You only need to enter the values for column A and the equations. The values in columns B, C, D, E, F, and G are examples of the measured or calculated values.
The PDF version of the technical reference manual (which you can download from www.tektronix.com/manuals), includes an empty spreadsheet for your convenience. To access and save the test spreadsheet, see the instructions in Appendix A: Example of a Vertical Position Accuracy Test Spreadsheet on page A-1.
ication
——
Probe 1X
1
Source
Ext Mode Auto Sample
Source Channel under test Measurements Mean
r is the recommended source.
3. Connect the oscilloscope, power supply, and voltmeter as shown in the following gure:
4. Set the power supply to the 1.8 V value shown in column A, the Approximate Test Voltage.
5. Adjust the vertical position knob for the DC line to position the line in the center of the screen.
6. Enter the voltage on the voltmeter and on the oscilloscope into the spreadsheet in the appropriate columns, B and C.
7. Repeat steps 4 through 6 for the values of 1.76 V through 0 V.
8. Swap the connections to the positive terminal of the power supply with those at the negative terminal as shown in
the following gure:
26 TBS1000B and TBS1000B-EDU Specications and Performance Verication
9. Repeat steps 4 through 6 for the values of -0.04 V through -1.8 V.
10. Enter the Minimum Margin number (cell I16) for the channel tested in the test record.
Performance Ver
ication
11. Repeat steps 1 through 10 for all input channels.
TBS1000B and TBS1000B-EDU Specications and Performance Verication 27
Performance Ver
Data verication. To verify data, set the spreadsheet to present a line graph of columns D, E, and F. Verify that no error
values (the blu involved in this example, refer to the data in the previous table (see step 1).
ication
e line in the center) go above the yellow line (upper line), or below the purple line (lower line). F or calculations
Figure 1: Example of a line graph for the Vertical Position Accuracy test
28 TBS1000B and TBS1000B-EDU Specications and Performance Verication
Example of a Vert
ical Position Accuracy Test Spreadsheet
Example of a Ve
This appendix contains a lled-in example of the vertical position accuracy (VPA) test spreadsheet that is used. (See page 25, Check Vertical Position Accuracy.)
The PDF version of this technical reference manual (Tektronix part number 077-1025-00) includes an empty VPA test spreadsheet for your convenience. To access and save the test spreadsheet:
1. Go to the Tektronix manuals Web site, www.tektronix.com/manuals.
2. Enter 077102500 in the Search Manuals eld and click Go.
3. Click Download for the TBS1000B and TBS1000B-EDU Series Digital Storage Oscilloscopes Technical Reference
Manual (Tektronix part number 077102500) and follow the instructions to download the le to your PC.
4. Open the PDF le in Adobe Reader (version 7 or later).
5. Click the Attachments tab or click View > Navigation Panels > Attachments to display the Attachments panel.
6. Double-click the VPA Test Table.xls le.
7. Click OK in the Launch Attachment dialog box. The test spreadsheet opens in your spreadsheet application and shows the Blank Test Record spreadsheet tab.
8. Click File > Save As to save the le to a name and location that you enter. You can now use the spreadsheet to enter
values for the vertical position accuracy test.
rtical Position Accuracy Test Spreadsheet
Sample Filled-In Vertical Position Accuracy Test Spreadsheet
Table 15: Vertical position accuracy test spreadsheet
ABC DEFGHI
1 Approx-
imate Test Vo lt­age
2 2.00 0.000
3 1.96 0.000 4 1.92 0.000
5
6 1.84 0.000
7
1.88 0.000
1.80 1.80 1.79 0.010 -0.02
DVM Mea­sured Voltage
Oscillo­scope Measured Voltage
Error Lower
Limit
‡‡‡
‡‡‡
‡‡‡
‡‡‡
‡‡‡
8
Up­per Limit
0.028 0.018
Margin
Volts­/div
Offset as a frac­tional division
Offset in volts
Total voltage offset
0.05
0.1
0.005
0.01=I2* I4+I5
TBS1000B and TBS1000B-EDU Specications and Performance Verication 29
Example of a Vert
Table 15: Vertical position accuracy test spreadsheet (cont.)
ical Position Accuracy Test Spreadsheet
8 1.76 1.76 1.75 0.010 -0.02
76
9 1.72 1.72 1.72 0.000 -0.02
72
10 1.68 1.68 1.68 0.000 -0.02
68
11 1.64 1.64 1.64 0.000 -0.02
64
12 1.60 1.6 1.6 0.000 -0.02
6
13 1.56 1.56 1.56 0.000 -0.02
56
14 1.52 1.52 1.52 0.000 -0.02
52
15 1.48 1.48 1.49 -0.01
0
16 1.44 1.44 1.45 -0.01
0
17 1.40 1.4 1.41 -0.01
0
18 1.36 1.36 1.37 -0.01
0
19 1.32 1.32 1.33 -0.01
0
20 1.28 1.28 1.29 -0.01
0
21 1.24 1.24 1.25 -0.01
0
22 1.20 1.2 1.21 -0.01
0
23 1.16 1.16 1.17 -0.01
0
24 1.12 1.12 1.13 -0.01
0
25 1.08 1.08 1.09 -0.01
0
26 1.04 1.04 1.05 -0.01
0
-0.02 48
-0.02 44
-0.02 4
-0.02 36
-0.02 32
-0.02 28
-0.02 24
-0.02 2
-0.02160.02160.012
-0.02120.02120.011
-0.02 08
-0.02 04
0.02760.018
0.02720.027
0.02680.027 Equa-
0.02640.026 Equa-
0.026 0.026 Equa-
0.02560.026
0.02520.025 Equa-
0.02480.015
0.02440.014 Mini-
0.024 0.014
0.02360.014
0.02320.013
0.02280.013
0.02240.012
0.022 0.012
0.02080.011
0.02040.010
Gain error
tion for cell D7
tion for cell E7
tion for cell F7
tion for cell G7
mum margin
1%
=B7-C7
=-F7
=(ABS( B7)*$I$8
+ $I$6)
=MIN (D7-
E7,F7­D7)
0.007= MIN
(G7:G97)
30 TBS1000B and TBS1000B-EDU Specications and Performance Verication
Table 15: Vertical position accuracy test spreadsheet (cont.)
Example of a Vert
ical Position Accuracy Test Spreadsheet
27 1.00 1 1.01 -0.01
0
28 0.96 0.96 0.966 -0.00
6
29 0.92 0.92 0.926 -0.00
6
30 0.88 0.88 0.886 -0.00
6
31 0.84 0.84 0.845 -0.00
5
32 0.80 0.8 0.805 -0.00
5
33 0.76 0.76 0.764 -0.00
4
34 0.72 0.72 0.724 -0.00
4
35 0.68 0.68 0.683 -0.00
3
36 0.64 0.64 0.643 -0.00
3
37 0.60 0.6 0.6 0.000 -0.01
38 0.56 0.56 0.561 -0.00
1
39 0.52 0.52 0.521 -0.00
1
40 0.48 0.48 0.481 -0.00
1
41 0.44 0.44 0.44 0.000 -0.01
42 0.40 0.4 0.401 -0.00
1
43 0.36 0.36 0.361 -0.00
1
44 0.32 0.32 0.32 0.000 -0.01
45 0.28 0.28 0.281 -0.00
1
46 0.24 0.24 0.244 -0.00
4
47 0.20 0.2 0.204 -0.00
4
48 0.16 0.16 0.163 -0.00
3
-0.02 0.02 0.010
-0.01 96
-0.01 92
-0.01 88
-0.01 84
-0.01 8
-0.01 76
-0.01 72
-0.01 68
-0.01 64
6
-0.01 56
-0.01 52
-0.01 48
44
-0.01 4
-0.01 36
32
-0.01 28
-0.01 24
-0.01 2
-0.01160.01160.009
0.01960.014
0.01920.013
0.01880.013
0.01840.013
0.018 0.013
0.01760.014
0.01720.013
0.01680.014
0.01640.013
0.016 0.016
0.01560.015
0.01520.014
0.01480.014
0.01440.014
0.014 0.013
0.01360.013
0.01320.013
0.01280.012
0.01240.008
0.012 0.008
TBS1000B and TBS1000B-EDU Specications and Performance Verication 31
Example of a Vert
Table 15: Vertical position accuracy test spreadsheet (cont.)
ical Position Accuracy Test Spreadsheet
49 0.12 0.12 0.123 -0.00
3
50 0.08 0.08 0.083 -0.00
3
51 0.04 0.04 0.043 -0.00
3
52 0.00 0 0.002 -0.00
2
53 -0.04 -0.04 -0.039 -0.00
1
54 -0.08 -0.079 -0.079 0.000 -0.01
55
56 -0.16 -0.159 -0.159 0.000 -0.011590.011590.012
57
58 -0.24 -0.239 -0.238 -0.00
59 -0.28 -0.279 -0.274 -0.00
60 -0.32 -0.319 -0.314 -0.00
61 -0.36 -0.359 -0.353 -0.00
62 -0.40 -0.399 -0.393 -0.00
63 -0.44 -0.439 -0.432 -0.00
64 -0.48 -0.48 -0.473 -0.00
65 -0.52 -0.52 -0.513 -0.00
66 -0.56 -0.56 -0.552 -0.00
67 -0.6 -0.6 -0.592 -0.00
68 -0.64 -0.64 -0.633 -0.00
69 -0.68 -0.68 -0.673 -0.00
70 -0.72 -0.72 -0.713 -0.00
-0.12 -0.12 -0.118 -0.00 2
-0.20 -0.199 -0.198 -0.00 1
1
5
5
6
6
7
7
7
8
8
7
7
7
-0.01120.01120.008
-0.01 08
-0.01 04
-0.01 0.01 0.008
-0.01 04
079
-0.01120.01120.009
-0.011990.011990.011
-0.01 239
-0.01 279
-0.01 319
-0.01 359
-0.01 399
-0.01 439
-0.01 48
-0.01 52
-0.01 56
-0.01 6
-0.01 64
-0.01 68
-0.01 72
0.01080.008
0.01040.007
0.01040.009
0.010790.011
0.012390.011
0.012790.008
0.013190.008
0.013590.008
0.013990.008
0.014390.007
0.01480.008
0.01520.008
0.01560.008
0.016 0.008
0.01640.009
0.01680.010
0.01720.010
32 TBS1000B and TBS1000B-EDU Specications and Performance Verication
Table 15: Vertical position accuracy test spreadsheet (cont.)
Example of a Vert
ical Position Accuracy Test Spreadsheet
71 -0.76 -0.76 -0.754 -0.00
6
72 -0.80 -0.8 -0.794 -0.00
6
73 -0.84 -0.84 -0.835 -0.00
5
74 -0.88 -0.88 -0.875 -0.00
5
75
76 -0.96 -0.96 -0.956 -0.00
77
78 -1.04 -1.04 -1.04 0.000 -0.02
79 -1.08 -1.08 -1.08 0.000 -0.02
80 -1.12 -1.12 -1.12 0.000 -0.02120.02120.021
81 -1.16 -1.16 -1.16 0.000 -0.02160.02160.022
-0.92 -0.92 -0.915 -0.00 5
4
-1.00 -1 -0.996 -0.00 4
-0.01 76
-0.01 8
-0.01 84
-0.01 88
-0.01 92
-0.01 96
-0.02 0.02 0.016
04
08
0.01760.012
0.018 0.012
0.01840.013
0.01880.014
0.01920.014
0.01960.016
0.02040.020
0.02080.021
82 -1.20 -1.2 -1.2 0.000 -0.02
2
83 -1.24 -1.24 -1.24 0.000 -0.02
24
84 -1.28 -1.28 -1.28 0.000 -0.02
28
85 -1.32 -1.32 -1.32 0.000 -0.02
32
86 -1.36 -1.36 -1.36 0.000 -0.02
36
87 -1.40 -1.4 -1.4 0.000 -0.02
4
88 -1.44 -1.44 -1.44 0.000 -0.02
44
89 -1.48 -1.48 -1.48 0.000 -0.02
48
90 -1.52 -1.52 -1.52 0.000 -0.02
52
91 -1.56 -1.56 -1.56 0.000 -0.02
56
92 -1.60 -1.6 -1.6 0.000 -0.02
6
0.022 0.022
0.02240.022
0.02280.023
0.02320.023
0.02360.024
0.024 0.024
0.02440.024
0.02480.025
0.02520.025
0.02560.026
0.026 0.026
TBS1000B and TBS1000B-EDU Specications and Performance Verication 33
Example of a Vert
Table 15: Vertical position accuracy test spreadsheet (cont.)
ical Position Accuracy Test Spreadsheet
93 -1.64 -1.64 -1.64 0.000 -0.02
64
94 -1.68 -1.68 -1.68 0.000 -0.02
68
95 -1.72 -1.72 -1.72 0.000 -0.02
72
96 -1.76 -1.76 -1.75 -0.01
0
97 -1.80 -1.8 -1.79 -0.01
0 98 -1.84 99 -1.88 100 -1.92 101 -1.96 102 -2.00
These test values are outside of the range in the specication.
-0.02 76
-0.02 8
‡‡‡
‡‡‡
‡‡‡
‡‡‡
‡‡‡
0.02640.026
0.02680.027
0.02720.027
0.02760.018
0.028 0.018
34 TBS1000B and TBS1000B-EDU Specications and Performance Verication
Index
Index
B
bandwidth tes
t, 20
C
calibration
Do Self Cal, 19
D
DC gain acc delay time accuracy test, 21
uracy test, 19
E
edge trigger s equipment required
performance verication, 17
external edg
test, 24
ensitivity test, 22
e trigger sensitivity
P
performance verication, 17
S
sample rate and delay time accuracy
test, 21 self calibra specications, 1
tion, 19
V
Vertical position a ccuracy test, 25
example li
example spreadsheet, 29
ne graph, 28
TBS1000B and TBS1000B-EDU Specications and Performance Verication 35
Loading...