Tektronix SPECMONBUP (Options 65, 66,,6566) Field Install Instructions

xx

SPECMONBUP (Options 65, 66, and 6566)
SPECMONB Series Real-Time Spectrum Analyzers

ZZZ

Digital I and Q Outputs and Zero Span Output Upgrades

Instructions

www.tektronix.com

P075106600*

*

075-1066-00

Copyright © Tektronix. All rights reserved. Licensed software products are owned by Tektronix or its subsidiaries
or suppliers, and are protected by national copyright laws and international treaty provisions.

Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication
supersedes that in all previously published material. Specifications and price change privileges reserved.

TEKTRONIX and TEK are registered trademarks of Tektronix, Inc.

Service safety summary

Only qualified personnel should perform service procedures. Read this Service
Safety Summary and the General Safety Summary located in the Service Manual

before perfo

Do Not Service Alone. Do not perform internal service or adjustments of this
product unless another person capable of rendering first aid and resuscitation is
present.

rming any service procedures.

Disconnec

disconnect the power cord from the mains power.

UseCareWhenServicingWithPowerOn. Dangerousvoltagesorcurrentsmay
exist in this product. Disconnect power, remove battery (if applicable), and
disconnect test leads before removing protective panels, soldering, or replacing
compon

To avoid electric shock, do not touch exposed connections.

tPower. To avoid electric shock, switch off the instrument power, then

ents.

SPECMONB Series Digital I/Q and Zero Span Upgrades 1

Kit description

Kit description

This kit describes the installation of the following Options:

Products

SPECMONB Ser

Option 65: Digital I and Q Outputs

Option 66: Zero Span Output

Option 6566: Digital I and Q Outputs and Zero Span Output

SPECMON3B. Allserialnumbers

SPECMON6B. Allserialnumbers

SPECMO

N26B. All serial numbers

ies.

2 SPECMONB Series Digital I/Q and Zero Span Upgrades

Kit p arts list

Kit description

The following table provides a list of parts contained in this kit. The kit contains
the same parts, regardless of which of the three options you ordered. The actual
option (or options) available is controlled with the option key provided in the kit.

Quantity Part number Description

1 075-1066-X

1 171-2191-

2 174-5106-XX

2 174-5195-XX

1 174-5213-XX

1 174-6418-XX

1 200-

4 211-0450-XX

8 211-1050-XX

1 863-0955-XX

XX

5317-XX

X

MANUAL, TECH INSTALLATION, SPECMONBUP
OPTIONS 65, 66, 6566

MANUAL,TECH; SVCPT-UPG; TEKTRONIX
SUPPLEMENTAL INFORMATION SHEET FOR
THE PEOPLE

CABLE, ASSEMBLY (I AND Q OUT, PANEL MOUNT),
SAFETY CO

CABLE ASSY ELEC: 2X 50P MDR CONN. 1.5M L, 18
TWIST PA

S REPUBLIC OF CHINA; CHINA ROHS

NTROLLED

IR, 100 OHM, 1 I/O, 13 GND, W/SHIELD

NOTE. These cables are not needed to install the Option.

They are supplied for external connections to the I and Q

connectors.

Output

CABLE ASSY, RIBBON; STATIC GROUND, 1X2; SAFETY

OLLED

CONTR

CABLE, COAX BNC-ST TO SMB-RA

COVER, REAR PANEL, OPTION (I AND Q / ZERO SPAN)

W, MACHINE; 2.5MM X 0.45 X 6MM, PNH, STEEL,

SCRE
ZINC PLATED, T8 TORX DRIVE

EW, MACHINE; 6-32 X 0.312 L, PNH, STEEL, ZINC

SCR
FINISH, T15

T BD SUBASSY; REAL TIME IQ AND LOG VIDEO

CK
OUTPUT, FUNCTIONALLY TESTED

1

/A

N

ABEL, EXPORT CONTROL CLASSIFICATION

L

NOTE. Export control label only applies to SPECMONB

Series instruments when installing Option 65 or Option 6566.

1

1

N/A LABEL, MANUFACTURED; OPTION KEY UPGRADE

LABEL

N/A LABEL, MANUFACTURED; PRODUCT LABEL, SAFETY

CONTROLLED

SPECMONB Series Digital I/Q and Zero Span Upgrades 3