Page 1
SignalVu-PC
Vector Analysis Software
Programmer Manual
*P077072117*
077-0721-17
Page 2
Page 3
SignalVu-PC
Vector Analysis Software
Programmer Manual
Register now!
Click the following link to protect your product.
www.tek.com/register
*P077072117*
077-0721-17
Page 4
Copyright © Tektronix. All rights reserved. Licensed software products are owned by Tektronix or its subsidiaries or suppliers, and are
protected by national copyright laws and international treaty provisions. Tektronix products are covered by U.S. and foreign patents, issued
and pending. Information in this publication supersedes that in all previously published material. Specifications and price change privileges
reserved.
TEKTRONIX and TEK are registered trademarks of Tektronix, Inc.
Contacting Tektronix
Tektronix, Inc.
14150 SW Karl Braun Drive
P.O. Box 500
Beaverton, OR 97077
USA
For product information, sales, service, and technical support:
• In North America, call 1-800-833-9200.
• Worldwide, visit to www.tek.com find contacts in your area.
Page 5
Table of Contents
Table of Contents
Preface..........................................................................................................................................................................................9
Related documentation.......................................................................................................................................................... 9
Getting Started............................................................................................................................................................................ 10
Overview of the Manual....................................................................................................................................................... 10
Setting up remote communication........................................................................................................................................11
Measurement support.......................................................................................................................................................... 14
Syntax and Commands...............................................................................................................................................................18
Command syntax................................................................................................................................................................. 18
Backus-Naur Form Definition........................................................................................................................................18
SCPI Commands and Queries......................................................................................................................................18
IEEE 488.2 Common Commands.................................................................................................................................22
Constructed Mnemonics............................................................................................................................................... 23
Command groups................................................................................................................................................................ 23
Functional groups......................................................................................................................................................... 23
Programming hints........................................................................................................................................................24
IEEE common commands................................................................................................................................................... 24
Obsolete commands............................................................................................................................................................ 25
Abort commands..................................................................................................................................................................26
Calculate commands........................................................................................................................................................... 26
Marker mnemonics....................................................................................................................................................... 44
Calibration commands......................................................................................................................................................... 45
Display commands...............................................................................................................................................................46
Fetch commands................................................................................................................................................................. 67
Initiate commands................................................................................................................................................................88
Input commands.................................................................................................................................................................. 88
Mass memory commands....................................................................................................................................................89
Specifying the File........................................................................................................................................................ 96
Output commands................................................................................................................................................................96
Read commands..................................................................................................................................................................98
Sense commands...............................................................................................................................................................119
Status commands.............................................................................................................................................................. 175
Source commands............................................................................................................................................................. 178
System commands............................................................................................................................................................ 178
Trace commands............................................................................................................................................................... 179
Trace mnemonics....................................................................................................................................................... 187
Trigger commands............................................................................................................................................................. 187
Unit commands.................................................................................................................................................................. 190
Retrieving response message........................................................................................................................................... 190
Command descriptions............................................................................................................................................................. 191
Calculate commands......................................................................................................................................................... 192
Calibration commands....................................................................................................................................................... 495
Display commands.............................................................................................................................................................504
DISPlay:AVTime[:MEASview<y>]:SELect:FIRSt........................................................................................................ 522
DISPlay:AVTime[:MEASview<y>]:SELect:SECond ................................................................................................... 522
SignalVu-PC Vector Analysis Software Programmer Manual 5
Page 6
Table of Contents
DISPlay:AVTime[:MEASview<y>]:SELect:THIRd....................................................................................................... 523
DISPlay:AVTime[:MEASview<y>]:SELect:FOURth.................................................................................................... 523
DISPlay:PULSe:CUMulative:STATistics[:MEASview<y>]:MFReqerror.......................................................................741
DISPlay:PULSe:OGRAm[:MEASview<y>]:FVTime:DETection...................................................................................750
DISPlay:PULSe:OGRAm[:MEASview<y>][:SCALe]:RSCale......................................................................................751
DISPlay:PULSe:OGRAm[:MEASview<y>]:WINDow:TRACe:GRATicule:GRID:STATe.............................................. 751
DISPlay:PULSe:OGRAm[:MEASview<y>]:TRACE:POINts........................................................................................752
DISPlay:SGRam[:MEASview<y>]:TIME:OVERlap..................................................................................................... 794
Fetch commands............................................................................................................................................................... 893
:FETCh:AVTime[:MEASview<y>]:AVERage:{FIRSt|SECond|THIRd|FOURth} ..........................................................913
:FETCh:AVTime[:MEASview<y>]:MAXimum:{FIRSt|SECond|THIRd|FOURth}..........................................................913
:FETCh:AVTime[:MEASview<y>]:MAXLocation:{FIRSt|SECond|THIRd|FOURth} ....................................................914
:FETCh:AVTime[:MEASview<y>]:MINimum:{FIRSt|SECond|THIRd|FOURth} ..........................................................915
:FETCh:AVTime[:MEASview<y>]:MINLocation:{FIRSt|SECond|THIRd|FOURth} ..................................................... 915
:FETCh:AVTime[:MEASview<y>]:RESult:{FIRSt|SECond|THIRd|FOURth}............................................................... 916
FETCh:SIGNalvu:ACQuisition:COUPling? (Query Only)..........................................................................................1187
FETCh:SIGNalvu:ACQuisition:TERMination? (Query Only) .................................................................................... 1187
FETCh:SIGNalvu:ACQuisition:MAX:RT:BW? (Query Only) ..................................................................................... 1188
Input commands.............................................................................................................................................................. 1293
Memory commands......................................................................................................................................................... 1300
MMEMory:AVTime[:MEASview<y>]:STORe:PLOT ................................................................................................. 1303
MMEMory:AVTime[:MEASview<y>]:STORe:PLOT:DONe .......................................................................................1304
MMEMory:SGRam[:MEASview<y>]:STORe:PLOT..................................................................................................1338
MMEMory:SGRam[:MEASview<y>]:STORe:PLOT:DONe (Query only)...................................................................1338
Output commands............................................................................................................................................................1357
Read commands..............................................................................................................................................................1366
READ:AVTime[:MEASview<y>]:AVERage:{FIRSt|SECond|THIRd|FOURth}? ........................................................ 1387
READ:AVTime[:MEASview<y>]:MAXimum:{FIRSt|SECond|THIRd|FOURth}?........................................................ 1387
READ:AVTime[:MEASview<y>]:MAXLocation:{FIRSt|SECond|THIRd|FOURth}? .................................................. 1388
READ:AVTime[:MEASview<y>]:MINimum:{FIRSt|SECond|THIRd|FOURth}? ........................................................ 1389
READ:AVTime[:MEASview<y>]:MINLocation:{FIRSt|SECond|THIRd|FOURth}? ....................................................1389
READ:AVTime[:MEASview<y>]:RESult:{FIRSt|SECond|THIRd|FOURth}?..............................................................1390
Sense commands............................................................................................................................................................ 1730
[SENSe]:AVTime[:MEASview<y>]:SELEcted:SOURce ........................................................................................... 1778
[SENSe]:AVTime[:MEASview<y>]:SPAN:LINK.........................................................................................................1778
[SENSe]:FVTime[:MEASview<y>]:FREQuency:SPAN:LINK ................................................................................... 1922
[SENSe]:FVTime[:MEASview<y>]:SELEcted:SOURce............................................................................................1926
[SENSe]:IQVTime[:MEASview<y>]:FREQuency:SPAN:LINK.................................................................................. 1928
[SENSe]:IQVTime[:MEASview<y>]:SELEcted:SOURce.......................................................................................... 1931
[SENSe]:PHVTime[:MEASview<y>]:FREQuency:SPAN:LINK................................................................................. 2122
[SENSe]:PHVTime[:MEASview<y>]:SELEcted:SOURce......................................................................................... 2125
SENSe:PULSe:CUMulative:HISTogram[:MEASview<y>]:SELEcted:SOURce.........................................................2152
[SENSe]:PULSe:CUMulative:STATistics[:MEASview<y>]:SELEcted:SOURce........................................................2153
[SENSe]:PULSe[:MEASview<y>]:STATistics:SELEcted:SOURce............................................................................2157
[SENSe]:PULSe:OGRAm[:MEASview<y>]:SELEcted:SOURce...............................................................................2162
[SENSe]:PULSe:OGRAm[:MEASview<y>]:ANALysis:FVTime:ONTime:LENgth..................................................... 2163
[SENSe]:PULSe:OGRAm[:MEASview<y>]:ANALysis:FVTime:INDependent:STARt............................................... 2163
[SENSe]:PULSe:OGRAm[:MEASview<y>]:ANALysis:FVTime:INDependent:LENgth..............................................2164
[SENSe]:PULSe:TRACe[:MEASview<y>]:SELEcted:SOURce................................................................................ 2167
6
Page 7
Table of Contents
[SENSe]:PULSe:RESult[:MEASview<y>]:SELEcted:SOURce ................................................................................2168
[SENSe]:SGRam[:MEASview<y>]:{BANDwidth|BWIDth}:OPTimization.................................................................. 2206
[SENSe]:SGRam[:MEASview<y>]:CLEar:RESults (No Query Form).......................................................................2209
[SENSe]:SGRam[:MEASview<y>]:TIME[:SCALe]:OVERlap....................................................................................2216
[SENSe]:SGRam[:MEASview<y>]:TIME[:SCALe]:ZOOM........................................................................................ 2218
[SENSe]:SGRam[:MEASview<y>]:TIME[:SCALe]:AUTO.........................................................................................2218
[SENSe]:SGRam[:MEASview<y>]:TIME[:SCALe]:STARt.........................................................................................2219
[SENSe]:SGRam[:MEASview<y>]:SELEcted:SOURce ...........................................................................................2219
[SENSe]:SIGNalvu:ACQuisition[:SOURce<x>]:CHANnel[:RF].................................................................................2225
[SENSe]:SIGNalvu:ACQuisition[:SOURce<x>]:CHANnel:I.......................................................................................2226
[SENSe]:SIGNalvu:ACQuisition[:SOURce<x>]:CHANnel:Q.....................................................................................2226
[SENSe]:SIGNalvu:ACQuisition[:SOURce<x>]:CHANnel:IPLus ............................................................................. 2227
[SENSe]:SIGNalvu:ACQuisition[:SOURce<x>]:CHANnel:IMINus............................................................................ 2227
[SENSe]:SIGNalvu:ACQuisition[:SOURce<x>]:CHANnel:QPLus.............................................................................2228
[SENSe]:SIGNalvu:ACQuisition[:SOURce<x>]:CHANnel:QMINus.......................................................................... 2228
[SENSe]:SIGNalvu:ACQuisition[:SOURce<x>]:REFlevel[:RF] ................................................................................ 2229
[SENSe]:SIGNalvu:ACQuisition[:SOURce<x>]: REFlevel:I......................................................................................2229
[SENSe]:SIGNalvu:ACQuisition[:SOURce<x>]:REFlevel:Q .................................................................................... 2230
[SENSe]:SIGNalvu:ACQuisition[:SOURce<x>]:REFlevel:IPLus ..............................................................................2230
[SENSe]:SIGNalvu:ACQuisition[:SOURce<x>]:REFlevel:IMINus.............................................................................2231
[SENSe]:SIGNalvu:ACQuisition[:SOURce<x>]:REFlevel:QPLus ............................................................................2232
[SENSe]:SIGNalvu:ACQuisition[:SOURce<x>]:REFlevel:QMINus ..........................................................................2232
[SENSe]:SIGNalvu:ACQuisition[:SOURce<x>]:EXTattn[:RF] .................................................................................. 2233
[SENSe]:SIGNalvu:ACQuisition[:SOURce<x>]:EXTattn:I ........................................................................................ 2233
[SENSe]:SIGNalvu:ACQuisition[:SOURce<x>]:EXTattn:Q ...................................................................................... 2234
[SENSe]:SIGNalvu:ACQuisition[:SOURce<x>]:EXTattn:IPLus ................................................................................2235
[SENSe]:SIGNalvu:ACQuisition[:SOURce<x>]:EXTattn:IMINus ..............................................................................2235
[SENSe]:SIGNalvu:ACQuisition[:SOURce<x>]:EXTattn:QPLus .............................................................................. 2236
[SENSe]:SIGNalvu:ACQuisition[:SOURce<x>]:EXTattn:QMINus ............................................................................2236
[SENSe]:SIGNalvu:ACQuisition[:SOURce<x>]:DESkew[:RF]..................................................................................2237
[SENSe]:SIGNalvu:ACQuisition[:SOURce<x>]:DESkew:I .......................................................................................2237
[SENSe]:SIGNalvu:ACQuisition[:SOURce<x>]:DESkew:Q......................................................................................2238
[SENSe]:SIGNalvu:ACQuisition[:SOURce<x>]:DESkew:IPLus ...............................................................................2239
[SENSe]:SIGNalvu:ACQuisition[:SOURce<x>]:DESkew:IMINus ............................................................................ 2239
[SENSe]:SIGNalvu:ACQuisition[:SOURce<x>]:DESkew:QPLus .............................................................................2240
[SENSe]:SIGNalvu:ACQuisition[:SOURce<x>]:DESkew:QMINus ...........................................................................2240
[SENSe]:SIGNalvu:ACQuisition:CONTrol:SOURce<x>:STATe................................................................................ 2241
[SENSe]:SIGNalvu:ACQuisition:INPuttype:REFlevel............................................................................................... 2241
[SENSe]:SIGNalvu:ACQuisition:GLOBal:REFlevel ................................................................................................. 2242
[SENSe]:SIGNalvu:ACQuisition[:SOURce<x>]:PERSrc:REFlevel .......................................................................... 2242
[SENSe]:SPECtrum[:MEASview<y>]:SELEcted:SOURce .......................................................................................2243
[SENSe]:SVPC:ACQuisition:CONTrol:TRIGger ...................................................................................................... 2273
[SENSe]:SVPC:ACQuisition:CONTrol:CHANnel ..................................................................................................... 2273
[SENSe]:TOVerview[:MEASview<y>]:SELEcted:SOURce.......................................................................................2277
Status commands............................................................................................................................................................ 2343
System commands.......................................................................................................................................................... 2392
Trace Commands.............................................................................................................................................................2423
TRACe<x>:FVTime[:MEASview<y>]:DETection.......................................................................................................2441
TRACe<x>:PHVTime[:MEASview<y>]:DETection.................................................................................................... 2454
SignalVu-PC Vector Analysis Software Programmer Manual 7
Page 8
Table of Contents
TRACe:SGRam[:MEASview<y>]:RESet...................................................................................................................2459
Trigger commands........................................................................................................................................................... 2580
TRIGger[:SEQuence]:EVENt:A:TYPE ..................................................................................................................... 2580
TRIGger[:SEQuence]:EVENt:A:EDGE:SOURce...................................................................................................... 2580
TRIGger[:SEQuence]:EVENt:A:EDGE:SOURce:TYPE............................................................................................2580
TRIGger[:SEQuence]:EVENt:A:EDGE:COUPling.................................................................................................... 2581
TRIGger[:SEQuence]:EVENt:A:EDGE:SLOPe ........................................................................................................2581
TRIGger[:SEQuence]:EVENt:A:EDGE:SOURce:FORMat .......................................................................................2581
TRIGger[:SEQuence]:EVENt:A:EDGE:LEVEl:ANAlog ............................................................................................ 2582
TRIGger[:SEQuence]:EVENt:A:EDGE:LEVEl:MAGNitude.......................................................................................2582
TRIGger[:SEQuence]:EVENt:A:EDGE:LEVEl:FREQuency......................................................................................2583
TRIGger[:SEQuence]:EVENt:A:EDGE:HOLDoff:TIME.............................................................................................2583
Status and Events................................................................................................................................................................... 2586
Status and event reporting system.................................................................................................................................. 2586
Status Byte.......................................................................................................................................................................2588
Standard event status block.............................................................................................................................................2590
Operation status block..................................................................................................................................................... 2591
Questionable Status Block...............................................................................................................................................2591
Queues............................................................................................................................................................................ 2593
Status and event processing sequence........................................................................................................................... 2594
Synchronizing execution.................................................................................................................................................. 2595
Error messages and codes.............................................................................................................................................. 2596
Command errors.......................................................................................................................................................2596
Execution errors........................................................................................................................................................2597
Device specific errors................................................................................................................................................2599
Query Errors............................................................................................................................................................. 2599
Device errors.............................................................................................................................................................2599
Status Conditions.............................................................................................................................................................2602
Global status.............................................................................................................................................................2602
Measurement status................................................................................................................................................. 2602
Source status............................................................................................................................................................2603
Appendices............................................................................................................................................................................. 2605
Appendix A: Character charts.......................................................................................................................................... 2605
Appendix B: SCPI conformance information....................................................................................................................2605
Appendix C: Creating a DPX Frame Access Plugin.........................................................................................................2607
Glossary.................................................................................................................................................................................. 2610
Glossary...........................................................................................................................................................................2610
8
Page 9
Preface
Preface
The SignalVu-PC Vector Signal Analysis Software enables you to use your PC to analyze RF signal behavior with the same software
used on the RSA6100B, RSA5100B, and RSA5100A Series Real-Time Analyzers. The SignalVu-PC software supports the use of the
RSA6100B, RSA5100B, and RSA5100A Series commands with some limitations. For example, commands that control functions that are
only available on RSA instruments.
When SignalVu-PC software is connected to an RSA306, RSA306B, RSA500A series, RSA600A series, or RSA7100A Spectrum Analyzer,
the software supports commands that control the functions of those instruments.
This manual is composed of the following sections:
• Getting Started outlines how to use the GPIB interface.
• Syntax and Commands defines the syntax used in command descriptions, presents a list of all command subsystems, and presents
detailed descriptions of all programming commands.
• Status and Events describes how the status and Events Reporting system operates and presents a list of all system errors.
• Appendices provides additional information including character charts, GPIB interface specification, and factory initialization settings.
Related documentation
• SignalVu-PC Vector Signal Analysis Software Help
The help contains detailed information about how to operate the application and is found in the SignalVu-PC application. A PDF of the
Help is also available at www.tek.com/manuals.
• TekVISA Programmer Manual
(Tektronix part number 077-0140-XX)
This manual is available as a printable PDF file on the Tektronix Web site (www.tek.com/manuals). The manual describes TekVISA,
the Tektronix implementation of the VISA Application Programming Interface (API). TekVISA is industry-compliant software for writing
interoperable instrument drivers in a variety of Application Development Environments (ADEs).
SignalVu-PC Vector Analysis Software Programmer Manual 9
Page 10
Getting Started
Getting Started
You can write computer programs that remotely take measurements and read those measurements for further analysis or storage. To help
you get started with programming, this section includes the following subsections.
• Overview of the Manual
Summarizes each major section of this manual.
• Measurement Support
Describes which RSA measurement displays are available with the software.
• Setting Up Remote Communication
Describes how to set up TekVISA, the programming interface, and enable control over the Ethernet.
Overview of the Manual
The information contained in each major section of this manual is described below.
Syntax and Commands
Syntax and Commands, describes the structure and content of the messages your program sends to the analyzer. The following figure
shows command parts as described in the Command Syntax subsection.
Figure 1: Command parts
Section 2 also describes the effect of each command and provides examples of how you might use it. The Command Groups subsection
provides lists by functional areas. The commands are listed alphabetically in the Command Descriptions section.
Figure 2: Functional groupings and an alphabetical list of commands
Status and Events
The program may request information from the instrument. The instrument provides information in the form of status and error messages.
The following figure illustrates the basic operation of this system. Section 3, Status and Events,describes how to get status or event
information from the program and details the event and error messages.
10
Page 11
Figure 3: Event-driven program
Setting up remote communication
Getting Started
To use the SignalVu-PC programmatic interface you must install the Tektronix Virtual Instrument Software Architecture (TekVISA) on your
PC. TekVISA is a Tektronix VISA solution provided for customers. It is a collection of software and documentation that allows for remote
control of instruments regardless of instrument brand and physical connection. It includes a VISA driver, VISA libraries, documentation,
USB Device Driver, VXI-11 server, and connection management/debug software.
TekVISA is included as part of the SignalVu-PC application software package and you can select to automatically install it.
Setup for the programming interface
Enable the programming interface and install TekVISA. The programming interface is automatically enabled as part of the SignalVu-PC
application software installation. However, in order to control SignalVu-PC using the programmatic interface, you must also install TekVISA,
as follows.
The programming interface is automatically enabled as part of the SignalVu-PC application software installation. However, in order to
control SignalVu-PC using the programmatic interface, you must also install TekVISA as follows.
1. Install SignalVu-PC.
2. When the installation is almost complete, the following dialog box will appear. Verify that the Install TekVISA box is checked.
SignalVu-PC Vector Analysis Software Programmer Manual 11
Page 12
Getting Started
3. Click Finish.
Enable control over the Ethernet
Communication with SignalVu-PC over an Ethernet LAN connection is supported with the VXI-11 protocal. The VXI-11 standard specifies
an instrument protocol for TCP/IP computer networks, supporting writing and reading data to and from instruments.
The VXI-11 server is automatically installed on the target PC as part of the SignalVu-PC application software installation process. This also
creates a shortcut in the Startup folder. Do the following two procedures to establish communication between the instrument and the PC
hosting SignalVu-PC.
1. Select the tray icon at the bottom right corner of the Windows Desktop to view hidden icons.
2. Right click the Server Control icon and select Server Properties.
3. When the TekVISA LAN Server Properties window opens, verify the Socket Server port is set to 5005. If it is not, change it to 5005.
12
Page 13
Getting Started
4. Click OK.
5. Right click the Server Control icon again and select Start Socket Server. This will start the socket server to enable communication
with the instrument and SignalVu-PC.
6. On the PC hosting SignalVu-PC, select the tray icon at the bottom right corner of the Windows Desktop to view hidden icons.
7. Click on theVISAResourceManager icon and select Instrument Manager from the menu.
8. Click the Search Criteria button and select the LAN tab.
SignalVu-PC Vector Analysis Software Programmer Manual 13
Page 14
Getting Started
9. Enter the IP address of the instrument in the Hostname field. (Use the address of the instrument for which you started the socket
server in the previous steps.)
10. Set to Socket and the Port to 5005.
11. Click the add icon arrow below it to add the address to the available sockets field and then click the Search button.
12. Select the added instrument from the Instruments list and click the Identify button. This will return the *IDN? response for
SignalVu-PC.
Measurement support
Each command works in a particular measurement view(s). Views are specified under the Conditionsheading in the command description.
The following table lists all available measurement displays supported by the SignalVu-PC software, which measurement view it is in, and
if it requires an installed option.
If you send a command for the measurement view that is not active on screen, an execution error will occur.
Note:
Note: Some measurement displays require installed options. See the Tektronix Web site product page for a list of available
options.
14
Page 15
Table 1: Measurement support
Measurement group Measurement
General signal viewing Amplitude vs Time
DPX®(Spectrum, DPXogram, and Split only)
Frequency vs Time
Phase vs Time
RF I&Q vs Time
Spectrogram
Spectrum
Time overview
Analog Modulation Amplitude modulation
Frequency modulation
Phase modulation
Settling Time
(requires Option SVTNL-SVPC or SVTFL-SVPC)
Freq Settling
Phase Settling
Getting Started
General purpose digital
modulation
(requires Option SVMNL-SVPC orSVMFL-SVPC)
RF Channel power and ACPR
Table continued…
Constellation
Demod I&Q versus Time
EVM vs Time
Eye Diagram
Freq Dev vs Time
Mag Error vs Time
Phase Error vs Time
Signal quality
Symbol table
Trellis
User defined filters
Freq Settling (requires Option SVT).
MCPR
Occupied Bandwidth
Phase Settling (requires Option SVT)
Signal Strength
SEM
Spurious
SignalVu-PC Vector Analysis Software Programmer Manual 15
Page 16
Getting Started
Measurement group Measurement
OFDM(requires Option SVONL-SVPC or SVOFL-SVPC) OFDM Channel Response
OFDM Constellation
OFDM EVM
OFDM Mag Error
OFDM Phase Error
OFDM Power
OFDM Summary
OFDM Symbol Table
OFDM Flatness
WLAN (Requires Option SV23NL/SV23FL-SVPC, SV24NL/SV24FLSVPC, or SV25NL/SV25FL-SVPC)
P25 Analysis (requires Option SV26)(Requires Option SV26NLSVPC or SV26FL-SVPC)
Bluetooth® Analysis (Requires Option SV27NL/SV27FL-SVPC or
SV31NL/SV31FL-SVPC)
Table continued…
WLAN Channel Response
WLAN Constellation
WLAN EVM
WLAN Flatness
WLAN Mag Error
WLAN Phase Error
WLAN Power vs Time
WLAN Summary
WLAN Symbol Table
SEM
P25 Eye Diagram
P25 Freq Dev vs Time
P25 Power vs Time
P25 Constellation
P25 Symbol Table
P25 Summary
MCPR
Time Overveiw
BT 20dB BW
BT CF Offset and Drift
BT Constellation
BT Eye Diagram
BT Freq Dev vs Time
BT Inband Emission
BT Summary
BT Symbol Table
Time Overview
16
Page 17
Measurement group Measurement
LTE Analysis (Requires Option SV28NL-SVPC or SV28FL-SVPC)
EMC Analysis (Requires option EMCVUNL-SVPC or EMCVUFLSVPC)
Tracking generator (Only for the RSA500A series and RSA600A
series) (Requires Option 04)
LTE ACLR
LTE Channel Spectrum
LTE Constellation
LTE Power vs Time
SEM
EMC-EMI
DPX
Spectrogram
Spectrum
Transmission Gain
Getting Started
Pulsed RF
(Requires Option SVPNL-SVPC or SVPFL-SVPC)
802.11ad Analysis
(Available for offline analysis only)
Return Loss (Requires Option 04 and Option SV60NL-SVPC or
SV60FL-SVPC) (Only for the RSA500A series and RSA600A
series)
5GNR Analysis(Requires Option 5GNRNL-SVPC)
Audio Analysis
(Requires Option SVANL-SVPC or SVAFL-SVPC)
Pulse statistics
Pulse table
Pulse trace
Pulse-Ogram
Cumulative Histogram
Cumulative Statistics
802.11ad Summary
802.11ad Symbol Table
802.11ad Constellation
802.11ad EVM vs Time
Cable Loss
RL/DTF
NR Constellation
NR Channel Power
NR Adjacent Channel Power
NR Spectral Emission Mask
NR Summary
Audio Spectrum
Audio Summary
SignalVu-PC Vector Analysis Software Programmer Manual 17
Page 18
Syntax and Commands
Syntax and Commands
Command syntax
This section contains information on the Standard Commands for Programmable Instruments (SCPI) and IEEE 488.2 Common Commands
you can use to program your RSA Series analyzer. The information is organized in the following subsections
• Backus-Naur Form Definition
• SCPI Commands and Queries
• IEEE 488.2 Common Commands
• Constructed Mnemonics
Backus-Naur Form Definition
This manual may describe commands and queries using the Backus-Naur Form (BNF) notation. The following table defines the standard
BNF symbols.
Table 2: BNF symbols and meanings
Symbol Meaning
< > Defined element
:= Is defined as
| Exclusive OR
{ } Group; one element is required
[ ] Optional; can be omitted
. . . Previous element(s) may be repeated
( ) Comment
SCPI Commands and Queries
SCPI is a standard created by a consortium that provides guidelines for remote programming of instruments. These guidelines provide
a consistent programming environment for instrument control and data transfer. This environment uses defined programming messages,
instrument responses, and data format across all SCPI instruments, regardless of manufacturer. The analyzer uses a command language
based on the SCPI standard.
The SCPI language is based on a hierarchical or tree structure as shown in the following figure that represents a subsystem. The top level
of the tree is the root node; it is followed by one or more lower-level nodes.
Figure 4: Example of SCPI subsystem hierarchy tree
You can create commands and queries from these subsystem hierarchy trees.Commands specify actions for the instrument to perform.
Queries return measurement data and information about parameter settings.
18
Page 19
Syntax and Commands
Creating Commands
SCPI commands are created by stringing together the nodes of a subsystem hierarchy and separating each node by a colon.
In the figure above, TRIGger is the root node and EVENt, GATed, INPut, and SOURce are lower-level nodes. To create a SCPI command,
start with the root node TRIGger and move down the tree structure adding nodes until you reach the end of a branch. Most commands and
some queries have parameters; you must include a value for these parameters. If you specify a parameter value that is out of range, the
parameter will be set to a default value. The command descriptions,list the valid values for all parameters.
For example, TRIGgerEVENt:SOURce EXTRear is a valid SCPI command created from the hierarchy tree. (See Figure 2.)
Creating Queries
To create a query, start at the root node of a tree structure, move down to the end of a branch, and add a question mark.
TRIGgerEVENt:SOURce? is an example of a valid SCPI query using the hierarchy tree in the figure. (See Figure 2.)
Query Responses
The query causes the analyzer to return information about its status or settings.When a query is sent to the analyzer, only the values are
returned. When the returned value is a mnemonic, it is noted in abbreviated format, as shown in the following table.
Table 3: Query response examples
Query Response
CALCulate:SPECtrum:MARKer:X 7.50E+9
SENSe:SPECtrum:FFT:WINDow BH4B
A few queries also initiate an operation action before returning information. For example, the *CAL? query runs a calibration.
Parameter Types
Every parameter in the command and query descriptions is of a specified type.The parameters are enclosed in brackets, such as <value>.
The parameter type is listed after the parameter and is enclosed in parentheses, for example, (Boolean).Some parameter types are
defined specifically for the RSA Series command set and some are defined by ANSI/IEEE 488.2-1987 as shown in the following table.
Table 4: Parameter types used in syntax descriptions
Parameter type Description Example
arbitrary block
Boolean Boolean numbers or values ON or 1; OFF or 0
binary Binary numbers #B0110
octal Octal numbers #Q57, #Q3
hexadecimal
NR12numeric
NR223 numeric
Table continued…
1
A specified length of arbitrary data #512234xxxxx . . . where 5 indicates that the
following 5 digits (12234) specify the length
of the data in bytes;xxxxx ... indicates the
data
2
Hexadecimal numbers (0-9, A, B, C, D, E, F)
#HAA, #H1
Integers 0, 1, 15, -1
Decimal numbers 1.2, 3.141516, -6.5
1
Defined in ANSI/IEEE 488.2 as "Definite Length Arbitrary Block Response Data."
2
An ANSI/IEEE 488.2-1992-defined parameter type.
3
Some commands and queries will accept an octal or hexadecimal value even though the parameter type is defined as NR1.
SignalVu-PC Vector Analysis Software Programmer Manual 19
Page 20
Syntax and Commands
Parameter type Description Example
NR3
2
Floating point numbers 3.1415E-9, -16.1E5
NRf2numeric
Flexible decimal number that may be type
See NR1, NR2, and NR3 examples
NR1, NR2 or NR3
string
4
Alphanumeric characters (must be within
"Testing 1, 2, 3"
quotation marks)
Special Characters
The Line Feed (LF) character (ASCII 10), and all characters in the range of ASCII 127-255 are defined as special characters. These
characters are used in arbitrary block arguments only; using these characters in other parts of any command yields unpredictable results.
Abbreviating Commands,Queries, and Parameters
You can abbreviate most SCPI commands, queries, and parameters to an accepted short form. This manual shows these short forms as
a combination of upper and lower case letters. The upper case letters indicate the accepted short form of a command. As shown in the
following figure, you can create a short form by using only the upper case letters. The accepted short form and the long form are equivalent
and request the same action of the instrument.
Figure 5: Example of abbreviating a command
The numeric suffix of a command or query may be included in either the long form or short form; the analyzer will default to
Note:
"1" if no suffix is used. In the above figure, the "3" of "MARKer3" indicates that the command is directed to Marker 3.
Chaining Commands and Queries
You can chain several commands or queries together into a single message. To create a chained message, first create a command or
query, add a semicolon(;), and then add more commands or queries and semicolons until the message is complete. If the command
following a semicolon is a root node, precede it with a colon (:). The following figure illustrates a chained message consisting of several
commands and queries. The single chained message should end in a command or query, not a semicolon. Responses to any queries in
your message are separated by semicolons.
4
Defined in ANSI/IEEE 488.2 as "String Response Data."
20
Page 21
Syntax and Commands
Figure 6: Example of chaining commands and queries
If a command or query has the same root and lower-level nodes as the previous command or query, you can omit these nodes. In the
following figure, the second command has the same root node (TRIGgerEVENt) as the first command, so these nodes can be omitted.
Figure 7: Example of omitting root and lower-level nodes in a chained message
Unit and SI Prefix
If the decimal numeric argument refers to amplitude, frequency, or time, you can express it using SI units instead of using the scaled
explicit point input value format <NR3>. (SI units are units that conform to the Systeme International d'Unites standard.) For example, you
can use the input format 200 mV or 1.0 MHz instead of 200.0E-3 or 1.0E+6, respectively, to specify voltage or frequency.
The following table lists the available units.
Table 5: Available units
Symbol Meaning
dB decibel (relative amplitude)
dBm decibel (absolute amplitude)
DEG degree (phase)
Hz hertz (frequency)
PCT percent (%)
s second (time)
V volt
The available SI prefixes are shown in the following table.
SignalVu-PC Vector Analysis Software Programmer Manual 21
Page 22
Syntax and Commands
Table 6: Available SI prefixes
SI prefix Z A F P N U M K
Corresponding power
10
-21
10
-18
10
-15
10
-12
10
-9
10
-6
10
-3
10
+3
MA
10
5
G T PE EX
+6
10
+9
10
+12
10
+15
10
You can omit a unit in a command, but you must include the unit when using a SI prefix. For example, frequency of 15 MHz can be
described as follows
15.0E6, 1.5E7Hz, 15000000, 15000000Hz, 15MHz, etc
("15M" is not allowed.)
Note that you can use either lower or upper case units and prefixes. The following examples have the same result, respectively.
170mHz, 170mHz, 170MHz, etc
250mv, 250mV, 250MV, etc
General Rules
Here are three general rules for using SCPI commands, queries, and parameters:
• You can use single (‘ ’) or double (“ ”) quotation marks for quoted strings, but you cannot use both types of quotation marks for the
same string.
correct "This string uses quotation marks correctly."
correct ‘This string also uses quotation marks correctly.'
incorrect "This string does not use quotation marks correctly.'
• You can use upper case, lower case, or a mixture of both cases for all commands, queries, and parameters.
+18
SENSE:SPECTRUM:FFT:LENGTH 1024
is the same as
sense:spectrum:fft:length 1024
and
SENSE:spectrum:FFT:length 1024
Literal strings (quoted) are case sensitive, for example, file names.
Note:
• No embedded spaces are allowed between or within nodes.
correct SENSE:SPECTRUM:FFT:LENGTH 1024
incorrect SENSE: SPECTRUM: FFT: LEN GTH 1024
IEEE 488.2 Common Commands
ANSI/IEEE Standard 488.2 defines the codes, formats, protocols, and usage of common commands and queries used on the interface
between the controller and the instruments.The analyzer complies with this standard.
Command and Query Structure
The syntax for an IEEE 488.2 common command is an asterisk (*) followed by a command and, optionally, a space and parameter value.
The syntax for an IEEE 488.2 common query is an asterisk (*) followed by a query and a question mark.All of the common commands and
queries are listed in the last part of the Syntax and Commands section. The following are examples of common commands:
5
When the unit is "Hz", "M" may be used instead of "MA" so that the frequency can be represented by "MHz"
22
Page 23
Syntax and Commands
• *ESE 16
• *CLS
The following are examples of common queries
• *ESR
• *IDN
Constructed Mnemonics
Some header mnemonics specify one of a range of mnemonics. For example, a trace mnemonic can be either TRACe1, TRACe2,
TRACe3, or TRACe4. You use these mnemonics in the command just as you do any other mnemonic. For example, there is a
TRACe1:SPECtrum:FUNCtion command, and there is also a TRACe2:SPECtrum:FUNCtion command. In the command descriptions, this
list of choices is abbreviated as TRACe<x>. The value of <x> is the upper range of valid suffixes. If the numeric suffix is omitted, the
analyzer uses the default value of "1".
Table 7: Constructed mnemonics
Symbol Meaning
MARKer<x> A marker specifier where <x> = 0, 1, 2, 3, or 4.
Refer to Marker Mnemonics
RANGe<x> A range specifier where <x> = 1 to 20.
Refer to [SENSe]:SPURious Subgroup for details.
SPUR<x> A spurious specifier where <x> = 1 to the number of spurious signals.
Refer to FETCh|:READ:SPURious Subgroup for details, respectively.
TRACe<x> A trace specifier where <x> = 0, 1, 2, 3, 4, or 5.
Refer to TRACe Commands for details.
Command groups
This section lists the analyzer commands in two ways. It first presents them by functional groups. It then lists them alphabetically.The
functional group list starts below.The alphabetical list provides more detail on each command. For the complete list of commands, see the
Command Descriptions section.
The analyzers conform to the Standard Commands for Programmable Instruments(SCPI) 1999.0 and IEEE Std 488.2-1987, except where
noted.
Items followed by question marks are queries; items without question marks are commands. Some items in this section have a question
mark in parentheses () in the command header section; this indicates that the item can be both a command and a query.
For the conventions of notation in this manual, refer to Command Syntax and following pages.
Functional groups
All commands are divided into groups as shown in the following table.
Table 8: List of command group
Command group Function
IEEE common Conforms to the IEEE Std 488.2.
Table continued…
SignalVu-PC Vector Analysis Software Programmer Manual 23
Page 24
Syntax and Commands
Command group Function
ABORt Resets the trigger system and stops measurements.
CALCulate Controls the markers and the search operations.
DISPlay Controls the display of measurement results and waveforms.
FETCh Retrieves the measurements from the last acquired data.
INITiate Controls data acquisition.
INPut Controls the characteristics of the signal input.
MMEMory Provides mass storage capabilities for the analyzer.
OUTPut Controls the characteristics of the signal output.
READ Obtains the measurement results with acquiring data.
SENSe Sets up detailed conditions for each measurement.
STATus Controls the status and event registers.
SYSTem Sets or queries system parameters for operation.
TRACe Controls trace activation and math operations.
UNIT Specifies fundamental units for measurement.
Programming hints
Here are some basic tips for using commands:
• Selecting a measurement item
Use Display commands to select or display the measurement view. [Example] DISPlay:GENeral:MEASview:NEW
SPECtrum Displays the spectrum view on the screen.
• Setting measurement parameters
Use Sense commands to set conditions for the measurement session. [Example] SENSe:SPECtrum:FREQuency:CENTer
1.5GHz Sets the center frequency to 1.5 GHz in the spectrum view.
• Processing waveforms arithmetically
Use Trace commands for math operation on waveforms. [Example] TRACe1:SPECtrum:FUNCtion AVERage Averages the
spectrum waveform.
• Measuring with the markers
Use Calculate commands to measure some quantity using the markers. [Example]
CALCulate:SPECtrum:MARKer1:MAXimum Positions the marker at the highest peak signal on the spectrum.
• Scaling the waveform
Use Display commands to change the waveform portion on screen. [Example]DISPlay:IQVTime:Y:SCALe 1.5 Sets the
vertical range to 1.5 V in the IQ versus Time graph.
The following sections list the commands by group.
IEEE common commands
The IEEE 488.2 common commands have a "*" prefix.
24
Page 25
Syntax and Commands
Table 9: Status and error commands
Command Description
*CLS Clears status.
*ESE Sets or queries the bits in the ESER register.
*ESR? Returns the contents of the SESR register.
*IDN? Returns the instrument identification code.
*OPC Synchronizes commands.
*OPT? Returns a list of options installed in your analyzer.
*RST Returns the instrument settings to the factory defaults.
*SRE Sets or queries the bits in the SRER register.
*STB? Returns the contents of the SBR using the MSS bit.
*WAI Prevents the analyzer from executing further commands.
Obsolete commands
The following table lists obsolete commands and their replacements.
Table 10: Obsolete and replacement commands
Obsolete commands Replacement commands
[SENSe:]PULSe:ANALyze:MEASurement:TI
ME:AUTO
[SENSe:]PULSe:ANALyze:MEASurement:TI
ME:STARt
[SENSe:]PULSe:ANALyze:MEASurement:TI
ME:STOP
[SENSe]:PULSe:FREFerence:CHIRpbw(?) SENSe:PULSe:MEASview<y>:FREFerence:CSLope
SENSe:PULSe:MEASview<y>:ANALyze:FDOMain:MEASurement:TIME:ALENgth
SENSe:PULSe:MEASview<y>:ANALyze:FDOMain:MEASurement:TIME:METHod
SENSe:PULSe:MEASview<y>:ANALyze:FDOMain:MEASurement:TIME:RLENgth
SENSe:PULSe:MEASview<y>:ANALyze:FDOMain:MEASurement:TIME:RLEVel
SENSe:PULSe:MEASview<y>:ANALyze:FDOMain:MEASurement:TIME:STARt
SENSe:PULSe:MEASview<y>:ANALyze:IRESponse:MEASurement:TIME:ALENgth
SENSe:PULSe:MEASview<y>:ANALyze:IRESponse:MEASurement:TIME:METHod
SENSe:PULSe:MEASview<y>:ANALyze:IRESponse:MEASurement:TIME:RLENgth
SENSe:PULSe:MEASview<y>:ANALyze:IRESponse:MEASurement:TIME:RLEVel
SENSe:PULSe:MEASview<y>:ANALyze:IRESponse:MEASurement:TIME:STARt
SENSe:PULSe:MEASview<y>:ANALyze:OVERshoot:MEASurement:TIME:ALENgth
SENSe:PULSe:MEASview<y>:ANALyze:OVERshoot:MEASurement:TIME:METHod
SENSe:PULSe:MEASview<y>:ANALyze:OVERshoot:MEASurement:TIME:RLENgth
SENSe:PULSe:MEASview<y>:ANALyze:OVERshoot:MEASurement:TIME:RLEVel
SENSe:PULSe:MEASview<y>:ANALyze:OVERshoot:MEASurement:TIME:STARt
Note: <y> is the Measurement Index. Range: 1–8 (based on number of sources of connected instrument), where MEASview<y>
keyword is optional and by default y is 1
SignalVu-PC Vector Analysis Software Programmer Manual 25
Page 26
Syntax and Commands
Abort commands
Use the Abort commands to reset the trigger system and to stop measurements.
Table 11: Abort commands
Command Description
ABORt Resets the trigger system and stops measurements.
Calculate commands
Use the Calculate commands to control the markers and the search operations.See the Index for commands not listed in the following
table.
Table 12: Calculate commands
Command Description
CALCulate:MARKer:ADD Adds a marker.
CALCulate:TXGain subcommand group Transmission Gain measurements
CALculate:TXGain:MARKer<x>:DELTa:X? Returns the delta marker frequency for the specified marker on the
trace.
CALculate:TXGain:MARKer<x>:DELTa:Y? Returns the delta marker amplitude for the specified marker on the
trace.
CALculate:TXGain:MARKer<x>:MAXimum Moves the specified marker to the highest peak on the trace.
CALculate:TXGain:MARKer<x>:PEAK:HIGHer Moves the specified marker to the next peak higher in amplitude on
the trace.
CALculate:TXGain:MARKer<x>:PEAK:LEF Moves the specified marker to the next peak to the left on the trace.
CALculate:TXGain:MARKer<x>:PEAK:LOWer Moves the specified marker to the next peak lower in amplitude on
the trace.
CALculate:TXGain:MARKer<x>:PEAK:RIGHt Moves the specified marker to the next peak to the right on the
trace.
CALculate:TXGain:MARKer<x>:TRACe Sets or queries the trace on which the specified marker is placed in
the Transmission Gain display.
CALculate:TXGain:MARKer<x>:X Sets or queries the horizontal position for the specified marker on
the trace.
CALculate:TXGain:MARKer<x>:Y? Queries the marker amplitude of the specified marker on the trace.
CALCulate:BLUEtooth subcommand group Bluetooth measurements
CALCulate:BLUEtooth:CONSte:MARKer<x>:DELTa:X[:TIME]? Queries the delta marker time for the selected marker.
CALCulate:BLUEtooth:CONSte:MARKer<x>:FDEViation? Queries the frequency deviation for the selected marker.
CALCulate:BLUETooth:CONSte:MARKer<x>:MAGNitude? Queries the magnitude readout of the selected marker.
CALCulate:BLUEtooth:CONSte:MARKer<x>:MAXimum Positions the selected marker at the symbol in the center of the
analyzed time record.
CALCulate:BLUEtooth:CONSte:MARKer<x>:PEAK:LEFT Moves the selected marker in the time domain to the next symbol
number to the left, relative to the previous marker position.
Table continued…
26
Page 27
Syntax and Commands
Command Description
CALCulate:BLUEtooth:CONSte:MARKer<x>:PEAK:RIGHt Moves the selected marker in the time domain to the next symbol
number to the right, relative to the previous marker position.
CALCulate:BLUETooth:CONSte:MARKer<x>:PHASe? Queries the phase readout of the selected marker
CALCulate:BLUEtooth:CONSte:MARKer<x>:SYMBol? Queries the symbol readout value for the selected marker.
CALCulate:BLUEtooth:CONSte:MARKer<x>:Trace Sets or queries the Trace for the selected marker.
CALCulate:BLUETooth:CONSte:MARKer<x>:VALue? Queries the value readout of the selected marker.
CALCulate:BLUEtooth:CONSte:MARKer<x>:X Sets or queries the time position of the selected marker.
CALCulate:BLUEtooth:EDIagram:MARKer<x>:DELTa:X[:TIME]? Returns the delta marker time for the selected marker.
CALCulate:BLUEtooth:EDIagram:MARKer<x>:DELTa:Y? Returns the delta marker time for the selected marker.
CALCulate:BLUEtooth:EDIagram:MARKer<x>:MAXimum Returns the delta marker amplitude for the selected markers.
CALCulate:BLUEtooth:EDIagram:MARKer<x>:PEAK:HIGHer Moves the selected marker to the highest peak.
CALCulate:BLUEtooth:EDIagram:MARKer<x>:PEAK:LEFT Moves the selected marker to the next peak to the left.
CALCulate:BLUEtooth:EDIagram:MARKer<x>:PEAK:LOWer Moves the selected marker to the next peak lower in amplitude.
CALCulate:BLUEtooth:EDIagram:MARKer<x>:PEAK:RIGHt Moves the selected marker to the next peak to the right.
CALCulate:BLUEtooth:EDIagram:MARKer<x>:TRACe The command places the selected marker on the I or Q trace in
theBluetooth eye diagram display. The query returns the name of
the tracewhere the current marker resides.
CALCulate:BLUEtooth:EDIagram:MARKer<x>:X[:TIME] Sets or queries the horizontal position (time) of the selected marker.
CALCulate:BLUEtooth:EDIagram:MARKer<x>:Y? Returns the vertical position of the selected marker.
CALCulate:BLUEtooth:FDVTIME:MARKer<x>:DELTa:X[:TIME]? Queries the delta marker time for the selected marker.
CALCulate:BLUEtooth:FDVTIME:MARKer<x>:DELTa:Y? Returns the delta marker amplitude for the selected marker .
CALCulate:BLUEtooth:FDVTime:MARKer<x>:MAXimum Moves the selected marker to the highest peak on the trace.
CALCulate:BLUEtooth:FDVTime:MARKer<x>:PEAK:HIGHer Moves the selected marker to the next peak higher in amplitude.
CALCulate:BLUEtooth:FDVTime:MARKer<x>:PEAK:LEFT Moves the selected marker to the next peak to the left on the trace .
CALCulate:BLUEtooth:FDVTime:MARKer<x>:PEAK:LOWer Moves the selected marker to the next peak lower in amplitude.
CALCulate:BLUEtooth:FDVTime:MARKer<x>:PEAK:RIGHT Moves the selected marker to the next peak to the right on the
trace.
CALCulate:BLUEtooth:FDVTIME:MARKer<x>:X[:TIME] Sets or queries the marker time.
CALCulate:BLUEtooth:FDVTIME:MARKer<x>:Y Sets or queries the marker amplitude.
CALCulate:BOBW:MARKer<x>:DELTa:X? Returns the delta marker frequency for the selected marker.
CALCulate:BOBW:MARKer<x>:DELTa:Y? Returns the delta marker frequency for the selected marker on the
Bluetooth 20 dB bandwidth measurement.
CALCulate:BOBW:MARKer<x>:MAXimum Positions the selected marker at the maximum value of the display.
CALCulate:BOBW:MARKer<x>:PEAK:HIGHer Moves the selected marker to the next peak higher in amplitude.
CALCulate:BOBW:MARKer<x>:PEAK:LEFT Moves the selected marker in the time domain to the left, relative to
the previous marker position on the trace.
CALCulate:BOBW:MARKer<x>:PEAK:LOWer Moves the selected marker to the next peak lower in amplitude.
CALCulate:BOBW:MARKer<x>:PEAK:RIGHt Moves the selected marker in the time domain to the right, relative
to the previous marker position on the trace.
Table continued…
SignalVu-PC Vector Analysis Software Programmer Manual 27
Page 28
Syntax and Commands
Command Description
CALCulate:BOBW:MARKer<x>[:SET]:CENTer Sets the center frequency to the value at the marker position.
CALCulate:BOBW:MARKer<x>:X Sets or queries the time position of the selected marker.
CALCulate:BOBW:MARKer<x>:Y? Returns the amplitude position of the selected marker.
CALCulate:DPX:MARKer subcommand group DPX power density readings
CALCulate:DPX:MARKer<x>:POWer:DENSity? Returns the power density of the specified marker.
CALCulate:DPX:MARKer<x>:POWer:IDensity? Returns the integrated power density reading between the MR
(reference marker) and the selected marker.
CALCulate:DPX:MARKer<x>:POWer:INTEgrated? Returns the integrated power reading between the MR (reference
marker) and the selected marker.
CALCulate:MARKer:MODE Sets or queries the marker mode.
CALCulate:NOISe subcommand group Noise and Gain measurements
CALCulate:NOISe:FIGure:MARKer<x>:DELTa:X? Queries the frequency difference between MR (reference marker)
and the selected marker
CALCulate:NOISe:FIGure:MARKer<x>:DELTa:Y? Queries the power difference value between MR (reference marker)
and the selected marker.
CALCulate:NOISe:FIGure:MARKer<x>:MAXimum Places the selected marker at the maximum value on the peak of
the trace.
CALCulate:NOISe:FIGure:MARKer<x>:PEAK:HIGHer Places the selected marker at the next highest peak on the trace.
CALCulate:NOISe:FIGure:MARKer<x>:PEAK:LEFT Places the selected marker at the next peak on the trace to the left
of the selected marker
CALCulate:NOISe:FIGure:MARKer<x>:PEAK:LOWer Places the selected marker at the next lowest peak on the trace.
CALCulate:NOISe:FIGure:MARKer<x>:PEAK:RIGHt Places the selected marker at the next peak on the trace to the right
of the selected marker.
CALCulate:NOISe:FIGure:MARKer<x>:TRACe Sets or queries which trace the specified marker is attached to.
CALCulate:NOISe:FIGure:MARKer<x>:X? Queries the frequency of the specified marker.
CALCulate:NOISe:FIGure:MARKer<x>:Y? Queries the vertical position (dB) of the specified marker.
CALCulate:NOISe:GAIN:MARKer<x>:DELTa:X? Query returns the frequency difference between MR (reference
marker) and the selected marker.
CALCulate:NOISe:GAIN:MARKer<x>:DELTa:Y? Query returns the power difference value between MR (reference
marker) and the selected marker.
CALCulate:NOISe:GAIN:MARKer<x>:MAXimum? Places the selected marker at the maximum value on the peak of
the trace.
CALCulate:NOISe:GAIN:MARKer<x>:PEAK:HIGHer? Places the selected marker at the next highest peak on the trace.
CALCulate:NOISe:GAIN:MARKer<x>:PEAK:LEFT? Places the selected marker at the next peak on the trace to the left
of the selected marker.
CALCulate:NOISe:GAIN:MARKer<x>:PEAK:LOWer? Places the selected marker at the next lowest peak on the trace.
CALCulate:NOISe:GAIN:MARKer<x>:PEAK:RIGHt? Places the specified marker on a specified trace. The query form
returns the trace on which the marker resides.
CALCulate:NOISe:GAIN:MARKer<x>:TRACe Sets or queries which trace the specified marker is attached to.
CALCulate:NOISe:GAIN:MARKer<x>:X? Queries the horizontal position of the specified marker.
Table continued…
28
Page 29
Syntax and Commands
Command Description
CALCulate:NOISe:GAIN:MARKer<x>:Y? Queries the vertical position of the specified marker.
CALCulate:NOISe:TEMPerature:MARKer<x>:DELTa:X? Returns the frequency difference between MR (reference marker)
and the selected marker.
CALCulate:NOISe:TEMPerature:MARKer<x>:DELTa:Y? Returns the temperature difference between MR (reference marker)
and the selected marker.
CALCulate:NOISe:TEMPerature:MARKer<x>:MAXimum? Places the selected marker at the maximum value on the peak of
the trace.
CALCulate:NOISe:TEMPerature:MARKer<x>:PEAK:HIGHer? Places the selected marker at the highest peak on the trace.
CALCulate:NOISe:TEMPerature:MARKer<x>:PEAK:LEFT? Places the selected marker at the next peak on the trace to the left
of the selected marker.
CALCulate:NOISe:TEMPerature:MARKer<x>:PEAK:LOWer? Places the selected marker at the next lowest peak on the trace.
CALCulate:NOISe:TEMPerature:MARKer<x>:PEAK:RIGHt? This command places the specified marker on a specified trace.
The query form returns the trace on which the marker resides.
CALCulate:NOISe:TEMPerature:MARKer<x>:TRACe Sets or queries which trace the specified marker is attached to.
CALCulate:NOISe:TEMPerature:MARKer<x>:X? Queries the frequency of the specified marker.
CALCulate:NOISe:TEMPerature:MARKer<x>:Y? Queries the temperature (Kelvin) at the specified marker.
CALCulate:NOISe:YFACtor:MARKer<x>:DELTa:X? Queries the frequency difference between MR (reference marker)
and the selected marker.
CALCulate:NOISe:YFACtor:MARKer<x>:DELTa:Y? Queries the power difference value between MR (reference marker)
and the selected marker.
CALCulate:NOISe:YFACtor:MARKer<x>:MAXimum Places the selected marker at the maximum value on the peak of
the trace.
CALCulate:NOISe:YFACtor:MARKer<x>:PEAK:LEFT? Places the selected marker at the next peak to the left on the trace.
CALCulate:NOISe:YFACtor:MARKer<x>:PEAK:LOWer? Places the selected marker at the next lowest peak on the trace.
CALCulate:NOISe:YFACtor:MARKer<x>:PEAK:RIGHt? Places the specified marker on a specified trace. The query form
returns the trace on which the marker resides.
CALCulate:NOISe:YFACtor:MARKer<x>:TRACe Sets or queries which trace the specified marker is attached to.
CALCulate:NOISe:YFACtor:MARKer<x>:X? Queries the frequency of the specified marker.
CALCulate:NOISe:YFACtor:MARKer<x>:Y? This command queries the vertical position (dB) of the specified
marker.
CALCulate:P25 subcommand group P25 analysis
CALCulate:P25:CONSte:MARKer<x>:DELTa:X[:TIME]? Returns the delta marker time for the selected marker.
CALCulate:P25:CONSte:MARKer<x>:FDEViation? Queries the frequency deviation of the selected marker.
CALCulate:P25:CONSte:MARKer<x>:MAGNitude? Queries the frequency deviation (for Freq Dev trace types) or
magnitude (for IQ trace types) of the selected marker.
CALCulate:P25:CONSte:MARKer<x>:MAXimum Moves the selected marker to the highest peak on the trace.
CALCulate:P25:CONSte:MARKer<x>:PEAK:LEFT Moves the selected marker to the next peak to the left on the trace.
CALCulate:P25:CONSte:MARKer<x>:PEAK:RIGHt Moves the selected marker to the next peak to the right on the
trace.
CALCulate:P25:CONSte:MARKer<x>:PHASe? Queries the phase of the selected marker.
Table continued…
SignalVu-PC Vector Analysis Software Programmer Manual 29
Page 30
Syntax and Commands
Command Description
CALCulate:P25:CONSte:MARKer<x>:SYMBol? Queries the readout symbol of the selected marker.
CALCulate:P25:CONSte:MARKer<x>:Trace Places the selected marker on the Demodulated I and Q versus
Time trace. The query returns the name of the trace on which the
marker resides.
CALCulate:P25:CONSte:MARKer<x>:VALue? Queries the readout value of the specified marker.
CALCulate:P25:CONSte:MARKer<x>:X Sets or queries the horizontal position of the selected marker.
CALCulate:P25:EDIagram:MARKer<x>:DELTa:X[:TIME]? Returns the delta marker time for the selected marker.
CALCulate:P25:EDIagram:MARKer<x>:DELTa:Y? Returns the delta marker time for the selected marker.
CALCulate:P25:EDIagram:MARKer<x>:MAXimum Moves the selected marker to the highest peak.
CALCulate:P25:EDIagram:MARKer<x>:PEAK:HIGHer Moves the selected marker to the next highest peak.
CALCulate:P25:EDIagram:MARKer<x>:PEAK:LEFT Moves the selected marker to the next peak to the left .
CALCulate:P25:EDIagram:MARKer<x>:PEAK:LOWer Moves the selected marker to the next lowest peak.
CALCulate:P25:EDIagram:MARKer<x>:PEAK:RIGHt Moves the selected marker to the next peak to the right .
CALCulate:P25:EDIagram:MARKer<x>:TRACe Sets the selected marker on the I or Q trace, or queries the trace
that the specified marker is on.
CALCulate:P25:EDIagram:MARKer<x>:X Sets or queries the horizontal position of the selected marker.
CALCulate:P25:EDIagram:MARKer<x>:Y Sets or queries the vertical position of the selected marker.
CALCulate:P25:PVTime:MARKer<x>:DELTa:X[:TIME]? Returns the delta marker time (seconds) for the selected marker.
CALCulate:P25:PVTime:MARKer<x>:DELTa:Y[:TIME]? Returns the Delta marker amplitude (dB) for the selected marker.
CALCulate:P25:PVTime:MARKer<x>:Maximum Moves the selected marker to the highest peak on the trace.
CALCulate:P25:PVTime:MARKer<x>:PEAK:HIGHer Moves the selected marker to the next peak higher in amplitude on
the trace.
CALCulate:P25:PVTime:MARKer<x>:PEAK:LEFT Moves the selected marker to the next peak to the left on the trace.
CALCulate:P25:PVTime:MARKer<x>:PEAK:LOWer Moves the selected marker to the next peak lower in amplitude on
the trace.
CALCulate:P25:PVTime:MARKer<x>:PEAK:RIGHt Moves the selected marker to the next peak to the right on the
trace.
CALCulate:P25:PVTime:MARKer<x>:X Sets or queries the horizontal position of the selected marker.
CALCulate:P25:PVTime:MARKer<x>:Y Sets or queries the vertical position of the selected marker.
CALCulate: Marker subgroup Marker position and values
CALCulate:SPECtrum[:MEASview<y>]:MARKer<x>:POWer:DENSity?Returns the power density of the specified marker.
CALCulate:SPECtrum[:MEASview<y>]:MARKer<x>:POWer:IDENSi
ty
CALCulate:SPECtrum[:MEASview<y>]:MARKer<x>:POWer:INTEgr
ated?
CALCulate:MARKer:AOFF Turns off all markers.
CALCulate:MARKer:DELete Deletes the last marker added.
CALCulate:MARKer:DENSity:EXCursion Sets or queries the minimum excursion of DPX signal density.
Table continued…
30
Returns the integrated power density reading between the MR
(reference marker) and the selected marker.
Returns the integrated power reading between the MR (reference
marker) and the selected marker.
Page 31
Syntax and Commands
Command Description
CALCulate:MARKer:DENSity:SMOothing Sets or queries the number of pixels squared for smoothing the
density.
CALCulate:MARKer:DENSity:THReshold Sets or queries the threshold of DPX signal density to detect peaks.
CALCulate:MARKer:DRAG:SEARch:STATe Enables or disables peak searching when dragging a marker in a
plot.
CALCulate:MARKer:MODE Sets or queries the marker mode.
CALCulate:MARKer:NOISe:MODE Sets or queries the marker noise mode.
CALCulate:MARKer:PEAK:EXCursion Sets or queries the minimum excursion level.
CALCulate:MARKer:PEAK:THReshold Sets or queries the threshold level to detect peaks.
CALCulate:SEARch subgroup Calculate search commands
CALCulate:SEARch:LIMit:FAIL? Queries whether the waveform cuts across the limit or not.
CALCulate:SEARch:LIMit:MATCh:BEEP[:STATe] Sets or queries whether to beep when a match occurs.
CALCulate:SEARch:LIMit:MATCh:SACQuire[:STATe] Sets or queries whether to stop acquiring data on match.
CALCulate:SEARch:LIMit:MATCh:SDATa[:STATe] Sets or queries whether to save the acquisition data automatically.
CALCulate:SEARch:LIMit:MATCh:SPICture[:STATe] Sets or queries whether to save the whole screen automatically.
CALCulate:SEARch:LIMit:MATCh:STRace[:STATe] Sets or queries whether to save the spectrum trace automatically.
CALCulate:SEARch:LIMit:OPERation Sets or queries the limit operation in the search function.
CALCulate:SEARch:LIMit:OPERation:FEED Sets or queries the data flow to be fed in the search operation.
CALCulate:SEARch:LIMit:OPERation:MASK:LOAD Loads the limit mask from a specified file for the search operation.
CALCulate:SEARch:LIMit:OPERation:MASK:STORE Stores the limit mask to a specified file for the search operation.
CALCulate:[:SEARch|:TEST]:LIMit[:STATe]:MATCh:FILE:LOCation Sets or queries the limit value in the search operation.
CALCulate:SEARch:LIMit:REPort:DATA? Returns the frequency range(s) that satisfy the search condition.
CALCulate:SEARch:LIMit:REPort:POINts? Returns the number of range(s) that satisfy the search condition.
CALCulate:SEARch:LIMit:STATe Sets or queries whether to enable or disable the search function.
CALCulate:ACPower subgroup Channel power and ACPR measurement
CALCulate:ACPower:MARKer<x>:DELTa:X? Returns the delta marker frequency for the selected marker.
CALCulate:ACPower:MARKer<x>:DELTa:Y? Returns the delta marker amplitude for the selected marker.
CALCulate:ACPower:MARKer<x>:MAXimum Moves the marker to the highest peak on the trace.
CALCulate:ACPower:MARKer<x>:PEAK:LEFT Moves the marker to the next peak to the left on the trace.
CALCulate:ACPower:MARKer<x>:PEAK:RIGHt Moves the marker to the next peak to the right on the trace.
CALCulate:ACPower:MARKer<x>:X Sets or queries the horizontal position of the marker.
CALCulate:ACPower:MARKer<x>:Y? Queries the marker amplitude of the selected marker.
CALCulate:{AM|FM|PM} subgroup (Option 21 only) AM/FM/PM measurement
CALCulate:{AM|FM|PM}:MARKer<x>:DELTa:X? Returns the delta marker time for the selected marker.
CALCulate:{AM|FM|PM}:MARKer<x>:DELTa:Y? Returns the delta marker amplitude for the selected marker.
CALCulate:{AM|FM|PM}:MARKer<x>:MAXimum Moves the marker to the highest peak on the trace.
CALCulate:{AM|FM|PM}:MARKer<x>:PEAK:HIGHer Moves the marker to the next peak higher in amplitude.
CALCulate:{AM|FM|PM}:MARKer<x>:PEAK:LEFT Moves the marker to the next peak to the left on the trace.
Table continued…
SignalVu-PC Vector Analysis Software Programmer Manual 31
Page 32
Syntax and Commands
Command Description
CALCulate:{AM|FM|PM}:MARKer<x>:PEAK:LOWer Moves the marker to the next peak lower in amplitude.
CALCulate:{AM|FM|PM}:MARKer<x>:PEAK:RIGHt Moves the marker to the next peak to the right on the trace.
CALCulate:{AM|FM|PM}:MARKer<x>:X Sets or queries the horizontal position (time) of the marker.
CALCulate:{AM|FM|PM}:MARKer<x>:Y? Queries the marker amplitude of the selected marker.
CALCulate:AUDio subgroup Audio measurements
CALCulate:AUDio:HARMonic:HNUMber Sets or queries the number of harmonics.
CALCulate:AUDio:HARMonic:NHNumber Sets or queries the number of non-harmonics.
CALCulate:AUDio:NHARmonic:EXCursion Sets or queries the non-harmonic excursion value.
CALCulate:AUDio:NHARmonic:IGNore Sets or queries the ignore region of the non-harmonics.
CALCulate:AUDio:NHARmonic:THReshold Sets or queries the non-harmonic threshold value.
CALCulate:AUDio:SPECtrum:MARKer<x>:DELTa:X? Returns the delta marker frequency for the selected marker on the
spectrum trace.
CALCulate:AUDio:SPECtrum:MARKer<x>:DELTa:Y? Returns the delta marker amplitude for the selected marker on the
spectrum trace.
CALCulate:AUDio:SPECtrum:MARKer<x>:MAXimum Moves the selected marker to the highest peak on the spectrum
trace.
CALCulate:AUDio:SPECtrum:MARKer<x>:PEAK:HIGHer Moves the selected marker to the next peak higher in amplitude on
the spectrum trace.
CALCulate:AUDio:SPECtrum:MARKer<x>:PEAK:LEFT Moves the selected marker to the next peak to the left on the
spectrum trace.
CALCulate:AUDio:SPECtrum:MARKer<x>:PEAK:LOWer Moves the selected marker to the next peak lower in amplitude on
the spectrum trace.
CALCulate:AUDio:SPECtrum:MARKer<x>:PEAK:RIGHt Moves the selected marker to the next peak to the right on the
spectrum trace.
CALCulate:AUDio:SPECtrum:MARKer<x>:TRACe Sets or queries the trace on which the specified marker is placed in
the spectrum measurement.
CALCulate:AUDio:SPECtrum:MARKer<x>:X Sets or queries the horizontal position of the selected marker on the
spectrum trace.
CALCulate:AUDio:SPECtrum:MARKer<x>:Y? Queries the marker amplitude of the selected marker on the
spectrum trace.
CALCulate:AVTime subgroup Frequency versus Time measurement
CALCulate:AVTime[:MEASview<y>]:MARKer<x>:DELTa:X? Returns the delta marker time for the selected marker.
CALCulate:AVTime[:MEASview<y>]:MARKer<x>:DELTa:Y? Returns the delta marker amplitude for the selected marker.
CALCulate:AVTime[:MEASview<y>]:MARKer<x>:MAXimum Moves the marker to the highest peak on the trace.
CALCulate:AVTime[:MEASview<y>]:MARKer<x>:PEAK:HIGHer Moves the marker to the next peak higher in amplitude.
CALCulate:AVTime[:MEASview<y>]:MARKer<x>:PEAK:LEFT Moves the marker to the next peak to the left on the trace.
CALCulate:AVTime[:MEASview<y>]:MARKer<x>:PEAK:LOWer Moves the marker to the next peak lower in amplitude.
CALCulate:AVTime[:MEASview<y>]:MARKer<x>:PEAK:RIGHt Moves the marker to the next peak to the right on the trace.
CALCulate:AVTime[:MEASview<y>]:MARKer<x>:TRACe Sets or queries the trace on which the marker is placed.
CALCulate:AVTime[:MEASview<y>]:MARKer<x>:X Sets or queries the horizontal position of the marker.
Table continued…
32
Page 33
Syntax and Commands
Command Description
CALCulate:AVTime[:MEASview<y>]:MARKer<x>:Y? Queries the marker amplitude of the selected marker.
CALCulate:CONSte subgroup (Option 21 only) Constellation measurement
CALCulate:CONSte:MARKer<x>:DELTa:X[:TIME]? Returns the delta marker time for the selected marker.
CALCulate:CONSte:MARKer<x>:FDEViation? Queries the frequency deviation of the selected marker.
CALCulate:CONSte:MARKer<x>:MAGNitude? Queries the magnitude readout of the marker.
CALCulate:CONSte:MARKer<x>:MAXimum Positions the marker at the symbol in the center of the time record.
CALCulate:CONSte:MARKer<x>:PEAK:LEFT Moves the marker in the time domain to the next lower symbol
number.
CALCulate:CONSte:MARKer<x>:PEAK:RIGHt Moves the marker in the time domain to the next higher symbol
number.
CALCulate:CONSte:MARKer<x>:PHASe? Queries the phase readout of the marker.
CALCulate:CONSte:MARKer<x>:SYMBol? Queries the symbol readout of the marker.
CALCulate:CONSte:MARKer<x>:VALue? Queries the value readout of the marker.
CALCulate:CONSte:MARKer<x>:X Sets or queries the time position of the marker on the trace.
CALCulate:DIQVtime subgroup (Option 21 only) Demodulated I&Q versus Time measurement
CALCulate:DIQVtime:MARKer<x>:DELTa:X[:TIME]? Returns the delta marker time for the selected marker.
CALCulate:DIQVtime:MARKer<x>:DELTa:Y? Returns the delta marker amplitude for the selected marker.
CALCulate:DIQVtime:MARKer<x>:MAXimum Moves the marker to the highest peak on the trace.
CALCulate:DIQVtime:MARKer<x>:PEAK:HIGHer Moves the marker to the next peak higher in amplitude.
CALCulate:DIQVtime:MARKer<x>:PEAK:LEFT Moves the marker to the next peak to the left on the trace.
CALCulate:DIQVtime:MARKer<x>:PEAK:LOWer Moves the marker to the next peak lower in amplitude.
CALCulate:DIQVtime:MARKer<x>:PEAK:RIGHt Moves the marker to the next peak to the right on the trace.
CALCulate:DIQVtime:MARKer<x>:TRACe Places the selected marker on the Demodulated I&Q versus Time
trace.
CALCulate:DIQVtime:MARKer<x>:X[:TIME] Sets or queries the horizontal position (time) of the marker.
CALCulate:DIQVtime:MARKer<x>:Y? Queries the marker amplitude of the selected marker.
CALCulate:DPX subgroup DPX spectrum measurement
CALCulate:DPX:MARKer<x>:DELTa:Y? Returns the delta marker amplitude for the selected marker.
CALCulate:DPX:MARKer<x>:MAXimum Moves the marker to the highest peak on the trace.
CALCulate:DPX:MARKer<x>:PEAK:HIGHer Moves the marker to the next peak higher in amplitude.
CALCulate:DPX:MARKer<x>:PEAK:LEFT Moves the marker to the next peak to the left on the trace.
CALCulate:DPX:MARKer<x>:PEAK:LOWer Moves the marker to the next peak lower in amplitude.
CALCulate:DPX:MARKer<x>:PEAK:RIGHt Moves the marker to the next peak to the right on the trace.
CALCulate:DPX:MARKer<x>[:SET]:CENTer Sets the center frequency to the marker frequency.
CALCulate:DPX:MARKer<x>:TRACe Sets or queries the trace to attach the marker to.
CALCulate:DPX:MARKer<x>:X:AMPLitude Sets or queries the amplitude position of the marker.
CALCulate:DPX:MARKer<x>:X[:FREQuency] Sets or queries the frequency position of the marker.
CALCulate:DPX:MARKer<x>:X:PHASe Sets or queries the phase position of the selected marker.
Table continued…
SignalVu-PC Vector Analysis Software Programmer Manual 33
Page 34
Syntax and Commands
Command Description
CALCulate:DPX:MARKer<x>:X:TIME Sets or queries the time position of the selected marker.
CALCulate:DPX:MARKer<x>:Y? Queries the marker amplitude of the selected marker.
CALCulate:EDIagram subgroup (Option 21 only) Eye diagram
CALCulate:EDIagram:MARKer<x>:DELTa:X[:TIME]? Returns the delta marker time for the selected marker.
CALCulate:EDIagram:MARKer<x>:DELTa:Y? Returns the delta marker amplitude for the selected marker.
CALCulate:EDIagram:MARKer<x>:MAXimum Moves the marker to the highest peak on the trace.
CALCulate:EDIagram:MARKer<x>:PEAK:HIGHer Moves the marker to the next peak higher in amplitude.
CALCulate:EDIagram:MARKer<x>:PEAK:LEFT Moves the marker to the next peak to the left on the trace.
CALCulate:EDIagram:MARKer<x>:PEAK:LOWer Moves the marker to the next peak lower in amplitude.
CALCulate:EDIagram:MARKer<x>:PEAK:RIGHt Moves the marker to the next peak to the right on the trace.
CALCulate:EDIagram:MARKer<x>:TRACe Places a marker on the I or Q trace in the eye diagram display.
CALCulate:EDIagram:MARKer<x>:X[:TIME] Sets or queries the horizontal position (time) of the marker.
CALCulate:EDIagram:MARKer<x>:Y? Queries the marker amplitude of the selected marker.
CALCulate:EVM subgroup (Option 21 only) EVM versus Time measurement
CALCulate:EVM:MARKer<x>:DELTa:X? Returns the delta marker time for the selected marker.
CALCulate:EVM:MARKer<x>:DELTa:Y? Returns the delta marker amplitude for the selected marker.
CALCulate:EVM:MARKer<x>:MAXimum Moves the marker to the highest peak on the trace.
CALCulate:EVM:MARKer<x>:PEAK:HIGHer Moves the marker to the next peak higher in amplitude.
CALCulate:EVM:MARKer<x>:PEAK:LEFT Moves the marker to the next peak to the left on the trace.
CALCulate:EVM:MARKer<x>:PEAK:LOWer Moves the marker to the next peak lower in amplitude.
CALCulate:EVM:MARKer<x>:PEAK:RIGHt Moves the marker to the next peak to the right on the trace.
CALCulate:EVM:MARKer<x>:X Sets or queries the horizontal position of the marker.
CALCulate:EVM:MARKer<x>:Y? Queries the marker amplitude of the selected marker.
CALCulate:FDVTime subgroup (Option 21 only) Frequency deviation versus Time measurement
CALCulate:FDVTime:MARKer<x>:DELTa:X[:TIME]? Returns the delta marker time for the selected marker.
CALCulate:FDVTime:MARKer<x>:DELTa:Y? Returns the delta marker frequency for the selected marker.
CALCulate:FDVTime:MARKer<x>:MAXimum Moves the marker to the highest peak on the trace.
CALCulate:FDVTime:MARKer<x>:PEAK:HIGHer Moves the marker to the next peak higher in amplitude.
CALCulate:FDVTime:MARKer<x>:PEAK:LEFT Moves the marker to the next peak to the left on the trace.
CALCulate:FDVTime:MARKer<x>:PEAK:LOWer Moves the marker to the next peak lower in amplitude.
CALCulate:FDVTime:MARKer<x>:PEAK:RIGHt Moves the marker to the next peak to the right on the trace.
CALCulate:FDVTime:MARKer<x>:X[:TIME] Sets or queries the horizontal position (time) of the marker.
CALCulate:FDVTime:MARKer<x>:Y? Queries the marker amplitude of the selected marker.
CALCulate:{FSETtling|PSETtling} subgroup Frequency and Phase Settling measurements
CALCulate:{FSETtling|PSETtling}:MARKer<x>:DELTa:X? Returns the delta marker time for the selected marker in the
Frequency and Phase Settling displays.
CALCulate:{FSETtling|PSETtling}:MARKer<x>:DELTa:Y? Returns the delta marker frequency for the selected marker in the
Frequency and Phase Settling displays.
Table continued…
34
Page 35
Syntax and Commands
Command Description
CALCulate:{FSETtling|PSETtling}:MARKer<x>:MAXimum Moves the selected marker to the highest peak on the trace in the
Frequency or Phase Settling display.
CALCulate:{FSETtling|PSETtling}:MARKer<x>:PEAK:HIGHer Moves the selected marker to the next peak higher in amplitude on
the Frequency or Phase Settling trace.
CALCulate:{FSETtling|PSETtling}:MARKer<x>:PEAK:LEFT Moves the selected marker to the next peak to the left on the trace
in the Frequency or Phase Settling display.
CALCulate:{FSETtling|PSETtling}:MARKer<x>:PEAK:LOWer Moves the selected marker to the next peak lower in amplitude on
the Frequency or Phase Settling trace.
CALCulate:{FSETtling|PSETtling}:MARKer<x>:PEAK:RIGHt Moves the selected marker to the next peak to the right on the trace
in the Frequency or Phase Settling display.
CALCulate:{FSETtling|PSETtling}:MARKer<x>:TRACe Sets or queries the trace on which the specified marker is placed in
the spectrum measurement
CALCulate:{FSETtling|PSETtling}:MARKer<x>:X Sets or queries the horizontal position of the selected marker in the
Frequency and Phase Settling display.
CALCulate:{FSETtling|PSETtling}:MARKer<x>:Y? Queries the marker amplitude of the selected marker in the
Frequency and Phase Settling display.
CALCulate:FVTime subgroup Frequency versus Time measurement
CALCulate:FVTime[:MEASview<y>]:MARKer<x>:DELTa:X? Returns the delta marker time for the selected marker.
CALCulate:FVTime[:MEASview<y>]:MARKer<x>:DELTa:Y? Returns the delta marker frequency for the selected marker.
CALCulate:FVTime[:MEASview<y>]:MARKer<x>:MAXimum Moves the marker to the highest peak on the trace.
CALCulate:FVTime[:MEASview<y>]:MARKer<x>:PEAK:HIGHer Moves the marker to the next peak higher in amplitude.
CALCulate:FVTime[:MEASview<y>]:MARKer<x>:PEAK:LEFT Moves the marker to the next peak to the left on the trace.
CALCulate:FVTime[:MEASview<y>]:MARKer<x>:PEAK:LOWer Moves the marker to the next peak lower in amplitude.
CALCulate:FVTime[:MEASview<y>]:MARKer<x>:PEAK:RIGHt Moves the marker to the next peak to the right on the trace.
CALCulate:FVTime[:MEASview<y>]:MARKer<x>:X Sets or queries the horizontal position of the marker.
CALCulate:FVTime[:MEASview<y>]:MARKer<x>:Y? Queries the marker amplitude of the selected marker.
CALCulate:IQVTime subgroup RF I&Q versus Time measurement
CALCulate:IQVTime[:MEASview<y>]:MARKer<x>:DELTa:X? Returns the delta marker time for the selected marker.
CALCulate:IQVTime[:MEASview<y>]:MARKer<x>:DELTa:Y? Returns the delta marker amplitude for the selected marker.
CALCulate:IQVTime[:MEASview<y>]:MARKer<x>:MAXimum Moves the marker to the highest peak on the trace.
CALCulate:IQVTime[:MEASview<y>]:MARKer<x>:PEAK:HIGHer Moves the marker to the next peak higher in amplitude.
CALCulate:IQVTime[:MEASview<y>]:MARKer<x>:PEAK:LEFT Moves the marker to the next peak to the left on the trace.
CALCulate:IQVTime[:MEASview<y>]:MARKer<x>:PEAK:LOWer Moves the marker to the next peak lower in amplitude.
CALCulate:IQVTime[:MEASview<y>]:MARKer<x>:PEAK:RIGHt Moves the marker to the next peak to the right on the trace.
CALCulate:IQVTime[:MEASview<y>]:MARKer<x>:TRACe Sets or queries the trace (I or Q) to place the marker.
CALCulate:IQVTime[:MEASview<y>]:MARKer<x>:X Sets or queries the horizontal position of the marker.
CALCulate:IQVTime[:MEASview<y>]:MARKer<x>:Y? Queries the marker amplitude of the selected marker.
CALCulate:MCPower subgroup MCPR measurement
CALCulate:MCPower:MARKer<x>:DELTa:X? Returns the delta marker frequency for the selected marker.
Table continued…
SignalVu-PC Vector Analysis Software Programmer Manual 35
Page 36
Syntax and Commands
Command Description
CALCulate:MCPower:MARKer<x>:DELTa:Y? Returns the delta marker amplitude for the selected marker.
CALCulate:MCPower:MARKer<x>:MAXimum Moves the marker to the highest peak on the trace.
CALCulate:MCPower:MARKer<x>:PEAK:LEFT Moves the marker to the next peak to the left on the trace.
CALCulate:MCPower:MARKer<x>:PEAK:RIGHt Moves the marker to the next peak to the right on the trace.
CALCulate:MCPower:MARKer<x>:X Sets or queries the horizontal position of the marker.
CALCulate:MCPower:MARKer<x>:Y? Queries the marker amplitude of the selected marker.
CALCulate:MERRor:MARKer<x>:DELTa:X? Magnitude error versus Time measurement
CALCulate:MERRor:MARKer<x>:DELTa:X? Returns the delta marker time for the selected marker.
CALCulate:MERRor:MARKer<x>:DELTa:Y? Returns the delta marker amplitude for the selected marker.
CALCulate:MERRor:MARKer<x>:MAXimum Moves the marker to the highest peak on the trace.
CALCulate:MERRor:MARKer<x>:PEAK:HIGHer Moves the marker to the next peak higher in amplitude.
CALCulate:MERRor:MARKer<x>:PEAK:LEFT Moves the marker to the next peak to the left on the trace.
CALCulate:MERRor:MARKer<x>:PEAK:LOWer Moves the marker to the next peak lower in amplitude.
CALCulate:MERRor:MARKer<x>:PEAK:RIGHt Moves the marker to the next peak to the right on the trace.
CALCulate:MERRor:MARKer<x>:X Sets or queries the horizontal position of the marker.
CALCulate:MERRor:MARKer<x>:Y? Queries the marker amplitude of the selected marker.
CALCulate:OBWidth subgroup Occupied Bandwidth measurement
CALCulate:OBWidth:MARKer<x>:DELTa:X? Returns the delta marker frequency for the selected marker.
CALCulate:OBWidth:MARKer<x>:DELTa:Y? Returns the delta marker amplitude for the selected marker.
CALCulate:OBWidth:MARKer<x>:MAXimum Moves the marker to the highest peak on the trace.
CALCulate:OBWidth:MARKer<x>:PEAK:HIGHer Moves the marker to the next peak higher in amplitude.
CALCulate:OBWidth:MARKer<x>:PEAK:LEFT Moves the marker to the next peak to the left on the trace.
CALCulate:OBWidth:MARKer<x>:PEAK:LOWer Moves the marker to the next peak lower in amplitude.
CALCulate:OBWidth:MARKer<x>:PEAK:RIGHt Moves the marker to the next peak to the right on the trace.
CALCulate:OBWidth:MARKer<x>[:SET]:CENTer Sets the center frequency to the value at the marker position.
CALCulate:OBWidth:MARKer<x>:X Sets or queries the horizontal position of the marker.
CALCulate:OBWidth:MARKer<x>:Y? Queries the marker amplitude of the selected marker.
CALCulate:OFDM subgroup Orthogonal frequency division multiplexing measurement
CALCulate:OFDM:CONSte:MARKer<x>:FREQuency Sets or queries the frequency position of the selected marker.
CALCulate:OFDM:CONSte:MARKer<x>:MAGNitude? Queries the marker magnitude of the selected marker.
CALCulate:OFDM:CONSte:MARKer<x>:PHASe? Queries the phase readout of the selected marker.
CALCulate:OFDM:CONSte:MARKer<x>:TIME Sets or queries the X position of the selected marker.
CALCulate:OFDM:CONSte:MARKer<x>:TYPE? Queries the data type of the selected marker.
CALCulate:OFDM:CONSte:MARKer<x>:VALue? Queries the value of the specified marker.
CALCulate:OFDM:CRESponse:MARKer<x>:DELTa:X? Returns the delta marker frequency for the selected marker.
CALCulate:OFDM:CRESponse:MARKer<x>:DELTa:Y? Returns the delta marker frequency for the selected marker.
CALCulate:OFDM:CRESponse:MARKer<x>:MAXimum Moves the selected marker to the highest peak.
Table continued…
36
Page 37
Syntax and Commands
Command Description
CALCulate:OFDM:CRESponse:MARKer<x>:PEAK:HIGHer Moves the selected marker to the next peak higher in amplitude.
CALCulate:OFDM:CRESponse:MARKer<x>:PEAK:LEFT Moves the selected marker to the next peak to the left.
CALCulate:OFDM:CRESponse:MARKer<x>:PEAK:LOWer Moves the selected marker to the next peak lower in amplitude.
CALCulate:OFDM:CRESponse:MARKer<x>:PEAK:RIGHt Moves the selected marker to the next peak to the right.
CALCulate:OFDM:CRESponse:MARKer<x>:X Sets or queries the horizontal position of the selected marker.
CALCulate:OFDM:CRESponse:MARKer<x>:Y? Returns the amplitude of the selected marker.
CALCulate:OFDM:FLATness:MARKer<x>:MAXimum Positions the specified marker at the maximum point on the trace.
CALCulate:OFDM:FLATness:MARKer<x>:PEAK:HIGHer Moves the specified marker to the next peak higher in amplitude on
the trace.
CALCulate:OFDM:FLATness:MARKer<x>:PEAK:LEFT Moves the specified marker to the next peak to the left on the trace.
CALCulate:OFDM:FLATness:MARKer<x>:PEAK:LOWer Moves the marker to the next peak lower in amplitude on the trace.
CALCulate:OFDM:FLATness:MARKer<x>:PEAK:RIGHt Moves the marker to the next peak to the right on the trace.
CALCulate:OFDM:FLATness:MARKer<x>:X Sets or queries the horizontal value at the selected marker position
on the points trace.
CALCulate:OFDM:FLATness:MARKer<x>:Y? Returns the value of the amplitude (vertical position) at the selected
marker position.
CALCulate:OFDM:TABLe:MARKer<x>:FREQuency Sets or queries the frequency position of the selected marker.
CALCulate:OFDM:TABLe:MARKer<x>:TIMe Sets or queries the marker time.
CALCulate:OFDM:TABLe:MARKer<x>:VALue? Queries the value readout of the selected marker.
CALCulate:PERRor subgroup (Option 21 only) Phase error versus Time measurement
CALCulate:PERRor:MARKer<x>:DELTa:X? Returns the delta marker time for the selected marker.
CALCulate:PERRor:MARKer<x>:DELTa:Y? Returns the delta marker phase for the selected marker.
CALCulate:PERRor:MARKer<x>:MAXimum Moves the marker to the highest peak on the trace.
CALCulate:PERRor:MARKer<x>:PEAK:HIGHer Moves the marker to the next peak higher in amplitude.
CALCulate:PERRor:MARKer<x>:PEAK:LEFT Moves the marker to the next peak to the left on the trace.
CALCulate:PERRor:MARKer<x>:PEAK:LOWer Moves the marker to the next peak lower in amplitude.
CALCulate:PERRor:MARKer<x>:PEAK:RIGHt Moves the marker to the next peak to the right on the trace.
CALCulate:PERRor:MARKer<x>:X Sets or queries the horizontal position of the marker.
CALCulate:PERRor:MARKer<x>:Y? Queries the marker amplitude of the selected marker.
CALCulate:PHVTime subgroup Phase versus Time measurement
CALCulate:PHVTime[:MEASview<y>]:MARKer<x>:DELTa:X? Returns the delta marker time for the selected marker.
CALCulate:PHVTime[:MEASview<y>]:MARKer<x>:DELTa:Y? Returns the delta marker phase for the selected marker.
CALCulate:PHVTime[:MEASview<y>]:MARKer<x>:MAXimum Moves the marker to the highest peak on the trace.
CALCulate:PHVTime[:MEASview<y>]:MARKer<x>:PEAK:HIGHer Moves the marker to the next peak higher in amplitude.
CALCulate:PHVTime[:MEASview<y>]:MARKer<x>:PEAK:LEFT Moves the marker to the next peak to the left on the trace.
CALCulate:PHVTime[:MEASview<y>:MARKer<x>:PEAK:LOWer Moves the marker to the next peak lower in amplitude.
CALCulate:PHVTime[:MEASview<y>]:MARKer<x>:PEAK:RIGHt Moves the marker to the next peak to the right on the trace.
CALCulate:PHVTime[:MEASview<y>]:MARKer<x>:X Sets or queries the horizontal position of the marker.
Table continued…
SignalVu-PC Vector Analysis Software Programmer Manual 37
Page 38
Syntax and Commands
Command Description
CALCulate:PHVTime[:MEASview<y>]:MARKer<x>:Y? Queries the marker amplitude of the selected marker.
CALCulate:PULSe subgroup Pulsed RF measurements
CALCulate:PULSe:STATistics[:MEASview<y>]:FFT:INDicator:X Sets or queries the frequency in Hz for the X cursor.
CALCulate:PULSe:STATistics[:MEASview<y>]:FFT:INDicator:Y? Returns the frequency level in dB for the Y cursor.
CALCulate:PULSe:STATistics[:MEASview<y>]:HISTogram:INDicato
r:X
CALCulate:PULSe:STATistics[:MEASview<y>]:HISTogram:INDicato
r:Y?
CALCulate:PULSe:STATistics[:MEASview<y>]:MARKer<x>:DELTa:X?Returns the delta marker frequency for the specified marker.
CALCulate:PULSe:STATistics[:MEASview<y>]:MARKer<x>:DELTa:Y?Returns the delta marker amplitude for the specified marker.
CALCulate:PULSe:STATistics[:MEASview<y>]:MARKer<x>:MAXimumMoves the marker to the highest peak on the trace.
Sets or queries the histogram indicator X value.
Queries the histogram indicator Yvalue.
CALCulate:PULSe:STATistics[:MEASview<y>]:MARKer<x>:PEAK:H
IGHer
CALCulate:PULSe:STATistics[:MEASview<y>]:MARKer<x>:PEAK:L
EFT
CALCulate:PULSe:STATistics[:MEASview<y>]:MARKer<x>:PEAK:L
OWer
CALCulate:PULSe:STATistics[:MEASview<y>]:MARKer<x>:PEAK:R
IGHt
CALCulate:PULSe:STATistics[:MEASview<y>]:MARKer<x>:X Sets or queries the horizontal position of the marker.
CALCulate:PULSe:STATistics[:MEASview<y>]:MARKer<x>:Y? Queries the marker amplitude of the selected marker.
CALCulate:PULSe:TRACe[:MEASview<y>]:MARKer<x>:DELTa:X? Returns the delta marker time for the selected marker.
CALCulate:PULSe:TRACe[:MEASview<y>]:MARKer<x>:DELTa:Y? Returns the delta marker amplitude for the selected marker.
CALCulate:PULSe:TRACe[:MEASview<y>]:MARKer<x>:MAXimum Moves the marker to the highest peak on the pulse trace.
CALCulate:PULSe:TRACe[:MEASview<y>]:MARKer<x>:PEAK:HIG
Her
CALCulate:PULSe:TRACe[:MEASview<y>]:MARKer<x>:PEAK:LEFTMoves the marker to the next peak to the left on the pulse trace.
CALCulate:PULSe:TRACe[:MEASview<y>]:MARKer<x>:PEAK:LO
Wer
CALCulate:PULSe:TRACe[:MEASview<y>]:MARKer<x>:PEAK:RIGHtMoves the marker to the next peak to the right on the pulse trace.
Moves the marker to the next peak higher in amplitude.
Moves the marker to the next peak to the left on the statistics trace.
Moves the marker to the next peak lower in amplitude.
Moves the marker to the next peak to the right on the statistics
trace.
Moves the marker to the next peak higher in amplitude.
Moves the marker to the next peak lower in amplitude.
CALCulate:PULSe:TRACe[:MEASview<y>]:MARKer<x>:X Sets or queries the horizontal position of the marker.
CALCulate:PULSe:TRACe[:MEASview<y>]:MARKer<x>:Y? Queries the marker amplitude of the selected marker.
CALCulate:SEARch subgroup Spectrogram measurement
CALCulate:SEARch:LIMit:FAIL? Queries whether the waveform cuts across the limit in the search
operation.
Table continued…
38
Page 39
Syntax and Commands
Command Description
CALCulate:SEARch:LIMit:MATCh:BEEP[:STATe] Sets or queries whether or not to emit a beep on match during run
or replay in the search operation.
CALCulate:SEARch:LIMit:MATCh:SACQuire[:STATe] Sets or queries whether or not to stop acquiring data on match
during run or replay in the search operation.
CALCulate:SEARch:LIMit:MATCh:SDATa[:STATe] Sets or queries whether or not to save automatically (AutoSave)
acquisition data on match during run in the search operation.
CALCulate:SEARch:LIMit:MATCh:SPICture[:STATe] Sets or queries whether or not to save automatically (AutoSave) the
whole screen on match during run in the search operation.
CALCulate:SEARch:LIMit:MATCh:STRace[:STATe] Sets or queries whether or not to save automatically (AutoSave) the
spectrum trace on match during run in the search operation.
CALCulate:SEARch:LIMit:OPERation Sets or queries the search condition parameter.
CALCulate:SEARch:LIMit:OPERation:FEED Sets or queries the data flow to be fed in the search operation.
CALCulate:SEARch:LIMit:OPERation:MASK:LOAD Loads the specified limit mask file for the search operation.
CALCulate:SEARch:LIMit:OPERation:MASK:STORE Saves the limit mask to a specified file.
CALCulate:[:SEARch|:TEST]:LIMit[:STATe]:MATCh:FILE:LOCation Sets or queries the limit value (in dB) in the search operation.
CALCulate:SEARch:LIMit:REPort:DATA? Queries the frequency range(s) that satisfy the search condition.
CALCulate:SEARch:LIMit:REPort:POINts? Queries the number of frequency range(s) that satisfy the search
condition.
CALCulate:SEARch:LIMit:STATe Sets or queries the search function (enabled or disabled).
CALCulate:SEM subgroup Spectral Emissions Mask measurement
CALCulate:SEM:MARKer<x>:DELTa:X? Returns the delta marker frequency for the selected marker.
CALCulate:SEM:MARKer<x>:DELTa:Y? Returns the delta marker amplitude for the selected marker.
CALCulate:SEM:MARKer<x>:MAXimum Moves the selected marker to the highest peak.
CALCulate:SEM:MARKer<x>:PEAK:HIGHer Moves the selected marker to the next peak higher in amplitude.
CALCulate:SEM:MARKer<x>:PEAK:LEFT Moves the selected marker to the next peak to the left.
CALCulate:SEM:MARKer<x>:PEAK:LOWer Moves the selected marker to the next peak lower in amplitude.
CALCulate:SEM:MARKer<x>:PEAK:RIGHt Moves the selected marker to the next peak to the right.
CALCulate:SEM:MARKer<x>[:SET]:CENTer Moves the specified marker to the center frequency.
CALCulate:SEM:MARKer<x>:X Sets or queries the horizontal position of the selected marker.
CALCulate:SEM:MARKer<x>:Y? Queries the marker amplitude of the selected marker.
[CALCulate]:SGRam subgroup Spectrogram measurements
CALCulate:SGRam[:MEASview<y>]:MARKer<x>:DELTa:X:FREQue
ncy?
CALCulate:SGRam[:MEASview<y>]:MARKer<x>:DELTa:X[:TIME]? Returns the delta marker time for the selected marker.
CALCulate:SGRam[:MEASview<y>]:MARKer<x>:DELTa:Y? Returns the delta marker amplitude for the selected marker.
CALCulate:SGRam[:MEASview<y>]:MARKer<x>:MAXimum Moves the marker to the highest peak on the trace.
CALCulate:SGRam[:MEASview<y>]:MARKer<x>:PEAK:HIGHer Moves the marker to the next peak higher in amplitude.
CALCulate:SGRam[:MEASview<y>]:MARKer<x>:PEAK:LEFT Moves the marker to the next peak to the left on the trace.
CALCulate:SGRam[:MEASview<y>]:MARKer<x>:PEAK:LOWer Moves the marker to the next peak lower in amplitude.
Table continued…
Returns the delta marker frequency for the selected marker.
SignalVu-PC Vector Analysis Software Programmer Manual 39
Page 40
Syntax and Commands
Command Description
CALCulate:SGRam[:MEASview<y>]:MARKer<x>:PEAK:RIGHt Moves the marker to the next peak to the right on the trace.
CALCulate:SGRam[:MEASview<y>]:MARKer<x>[:SET]:CENTer Sets the center frequency to the marker frequency.
CALCulate:SGRam[:MEASview<y>]:MARKer<x>:X:FREQuency Sets or queries the marker frequency.
CALCulate:SGRam[:MEASview<y>]:MARKer<x>:X[:TIME] Sets or queries the marker time.
CALCulate:SGRam[:MEASview<y>]:MARKer<x>:Y? Queries the marker amplitude of the selected marker.
CALCulate:SPECtrum subgroup Spectrogram measurement
CALCulate:SPECtrum[:MEASview<y>]:MARKer<x>:DELTa:X? Returns the delta marker frequency for the selected marker.
CALCulate:SPECtrum[:MEASview<y>]:MARKer<x>:DELTa:Y? Returns the delta marker amplitude for the selected marker.
CALCulate:SPECtrum[:MEASview<y>]:MARKer<x>:MAXimum Moves the marker to the highest peak on the trace.
CALCulate:SPECtrum[:MEASview<y>]:MARKer<x>:PEAK:HIGHer Moves the marker to the next peak higher in amplitude.
CALCulate:SPECtrum[:MEASview<y>]:MARKer<x>:PEAK:LEFT Moves the marker to the next peak to the left on the trace.
CALCulate:SPECtrum[:MEASview<y>]:MARKer<x>:PEAK:LOWer Moves the marker to the next peak lower in amplitude.
CALCulate:SPECtrum[:MEASview<y>]:MARKer<x>:PEAK:RIGHt Moves the marker to the next peak to the right on the trace.
CALCulate:SPECtrum[:MEASview<y>]:MARKer<x>[:SET]:CENTer Sets the center frequency to the marker frequency.
CALCulate:SPECtrum[:MEASview<y>]:MARKer<x>:TRACe Sets or queries the trace on which the marker is placed.
CALCulate:SPECtrum[:MEASview<y>]:MARKer<x>:X Sets or queries the horizontal position of the marker.
CALCulate:SPECtrum[:MEASview<y>]:MARKer<x>:Y? Queries the marker amplitude of the selected marker.
CALCulate:SPURious subgroup Spurious measurement
CALCulate:SPURious:MARKer<x>:DELTa:X? Returns the delta marker frequency for the selected marker.
CALCulate:SPURious:MARKer<x>:DELTa:Y? Returns the delta marker amplitude for the selected marker.
CALCulate:SPURious:MARKer<x>:MAXimum Moves the marker to the highest peak on the trace.
CALCulate:SPURious:MARKer<x>:PEAK:HIGHer Moves the marker to the next peak higher in amplitude.
CALCulate:SPURious:MARKer<x>:PEAK:LEFT Moves the marker to the next peak to the left on the trace.
CALCulate:SPURious:MARKer<x>:PEAK:LOWer Moves the marker to the next peak lower in amplitude.
CALCulate:SPURious:MARKer<x>:PEAK:RIGHt Moves the marker to the next peak to the right on the trace.
CALCulate:SPURious:MARKer<x>[:SET]:CENTer Sets the center frequency to the marker frequency.
CALCulate:SPURious:MARKer<x>:X Sets or queries the horizontal position of the marker.
CALCulate:SPURious:MARKer<x>:Y? Queries the marker amplitude of the selected marker.
CALCulate:TDIagram subgroup (Option 21 only) Trellis diagram
CALCulate:TDIagram:MARKer<x>:DELTa:X[:TIME]? Returns the delta marker time for the selected marker.
CALCulate:TDIagram:MARKer<x>:DELTa:Y? Returns the delta marker amplitude for the selected marker.
CALCulate:TDIagram:MARKer<x>:MAXimum Moves the marker to the highest peak on the trace.
CALCulate:TDIagram:MARKer<x>:PEAK:HIGHer Moves the marker to the next peak higher in amplitude.
CALCulate:TDIagram:MARKer<x>:PEAK:LEFT Moves the marker to the next peak to the left on the trace.
CALCulate:TDIagram:MARKer<x>:PEAK:LOWer Moves the marker to the next peak lower in amplitude.
CALCulate:TDIagram:MARKer<x>:PEAK:RIGHt Moves the marker to the next peak to the right on the trace.
CALCulate:TDIagram:MARKer<x>:X[:TIME] Sets or queries the horizontal position (time) of the marker.
Table continued…
40
Page 41
Syntax and Commands
Command Description
CALCulate:TDIagram:MARKer<x>:Y? Queries the marker amplitude of the selected marker.
CALCulate:TOVerview subgroup Time overview
CALCulate:TOVerview[:MEASview<y>]:MARKer<x>:DELTa:X? Returns the delta marker time for the selected marker.
CALCulate:TOVerview[:MEASview<y>]:MARKer<x>:DELTa:Y? Returns the delta marker amplitude for the selected marker.
CALCulate:TOVerview[:MEASview<y>]:MARKer<x>:MAXimum Moves the marker to the highest peak on the trace.
CALCulate:TOVerview[:MEASview<y>[:MARKer<x>:PEAK:HIGHer Moves the marker to the next peak higher in amplitude.
CALCulate:TOVerview[:MEASview<y>[:MARKer<x>:PEAK:LEFT Moves the marker to the next peak to the left on the trace.
CALCulate:TOVerview[:MEASview<y>]:MARKer<x>:PEAK:LOWer Moves the marker to the next peak lower in amplitude.
CALCulate:TOVerview[:MEASview<y>]:MARKer<x>:PEAK:RIGHt Moves the marker to the next peak to the right on the trace.
CALCulate:TOVerview[:MEASview<y>]:MARKer<x>:X Sets or queries the horizontal position of the marker
CALCulate:TOVerview[:MEASview<y>]:MARKer<x>:Y? Queries the marker amplitude of the selected marker.
CALCulate:WLAN subgroup Wireless LAN measurement
CALCulate:WLAN:CONSte:MARKer<x>:FREQuency Sets or queries the frequency value of the marker.
CALCulate:WLAN:CONSte:MARKer<x>:MAGNitude? Returns the magnitude value at the indicated marker position.
CALCulate:WLAN:CONSte:MARKer<x>:PHASe? Returns the phase value at the indicated marker position.
CALCulate:WLAN:CONSte:MARKer<x>:TIME Sets the time offset value at the selected marker position on the
points trace.
CALCulate:WLAN:CONSte:MARKer<x>:TYPE? Returns the data type of the subcarrier for data at the indicated
marker position.
CALCulate:WLAN:CONSte:MARKer<x>:VALue? Queries the value readout at the selected marker position on the
points trace.
CALCulate:WLAN:CRESponse:MARKer<x>:DELTa:X? Queries the delta Subcarrier or frequency value at the selected
marker position.
CALCulate:WLAN:CRESponse:MARKer<x>:DELTa:Y? Queries the vertical delta value for the points trace at the selected
marker position.
CALCulate:WLAN:CRESponse:MARKer<x>:MAXimum Moves the marker to the highest peak on the trace.
CALCulate:WLAN:CRESponse:MARKer<x>:PEAK:HIGHer Moves the marker to the next peak higher in amplitude.
CALCulate:WLAN:CRESponse:MARKer<x>:PEAK:LEFT Moves the marker to the next peak on the left on the trace.
CALCulate:WLAN:CRESponse:MARKer<x>:PEAK:LOWer Moves the marker to the next peak lower in amplitude.
CALCulate:WLAN:CRESponse:MARKer<x>:PEAK:RIGHt Moves the marker to the next peak to the right on the trace.
CALCulate:WLAN:CRESponse:MARKer<x>:X Sets or queries the value of the horizontal position for the selected
marker.
CALCulate:WLAN:CRESponse:MARKer<x>:Y? Returns the value of the amplitude at the selected marker position.
CALCulate:WLAN:EVM:MARKer<x>:AVERage:SUBCarrier? Queries the EVM value at the selected marker position on the
average trace.
CALCulate:WLAN:EVM:MARKer<x>:AVERage:SYMBol? Queries the EVM value at the selected marker position on the
average trace.
CALCulate:WLAN:EVM:MARKer<x>:DELTa:SUBCarrier? Queries the delta Subcarrier or frequency value at the selected
marker position.
Table continued…
SignalVu-PC Vector Analysis Software Programmer Manual 41
Page 42
Syntax and Commands
Command Description
CALCulate:WLAN:EVM:MARKer<x>:DELTa:SYMBol? Queries the delta time value in seconds or symbols at the selected
marker position.
CALCulate:WLAN:EVM:MARKer<x>:DELTa:Y? Queries the vertical delta value for the points trace at the selected
marker position.
CALCulate:WLAN:EVM:MARKer<x>:FREQuency Sets or queries the frequency value of the marker.
CALCulate:WLAN:EVM:MARKer<x>:TIME Sets the vertical marker value of the points trace.
CALCulate:WLAN:EVM:MARKer<x>:VALue? Queries the EVM value at the selected marker position.
CALCulate:WLAN:FLATness:MARKer<x>:MAXimum Positions the specified marker at the maximum point on the trace.
CALCulate:WLAN:FLATness:MARKer<x>:PEAK:HIGHer Moves the specified marker to the next peak higher in amplitude.
CALCulate:WLAN:FLATness:MARKer<x>:PEAK:LEFT Moves the specified marker to the next peak to the left.
CALCulate:WLAN:FLATness:MARKer<x>:PEAK:LOWer Moves the marker to the next peak lower in amplitude.
CALCulate:WLAN:FLATness:MARKer<x>:PEAK:RIGHt Moves the marker to the next peak to the right.
CALCulate:WLAN:FLATness:MARKer<x>:X Sets or queries the horizontal position for the selected marker.
CALCulate:WLAN:FLATness:MARKer<x>:Y? Returns the value of the amplitude (vertical position) at the selected
marker position.
CALCulate:WLAN:MERRor:MARKer<x>:AVERage:SUBCarrier? Queries the value readout at the selected marker position on the
average trace.
CALCulate:WLAN:MERRor:MARKer<x>:AVERage:SYMBol? Queries the value readout at the selected marker position on the
average trace.
CALCulate:WLAN:MERRor:MARKer<x>:DELTa:SUBCarrier? Queries the delta Subcarrier or frequency value at the selected
marker position.
CALCulate:WLAN:MERRor:MARKer<x>:DELTa:SYMBol? Queries the delta time value in seconds or symbols at the selected
marker position.
CALCulate:WLAN:MERRor:MARKer<x>:DELTa:Y? Queries the vertical delta value for the points trace at the selected
marker position.
CALCulate:WLAN:MERRor:MARKer<x>:FREQuency Sets or queries the frequency value of the marker.
CALCulate:WLAN:MERRor:MARKer<x>:TIME Sets the time offset value at the selected marker position.
CALCulate:WLAN:MERRor:MARKer<x>:VALue? Queries the value readout at the selected marker position.
CALCulate:WLAN:PERRor:MARKer<x>:AVERage:SUBCarrier? Queries the Phase Error value at the selected marker position on
the average trace.
CALCulate:WLAN:PERRor:MARKer<x>:AVERage:SYMBol? Queries the Phase Error value at the selected marker position on
the average trace.
CALCulate:WLAN:PERRor:MARKer<x>:DELTa:SUBCarrier? Queries the delta Subcarrier or frequency value at the selected
marker position.
CALCulate:WLAN:PERRor:MARKer<x>:DELTa:SYMBol? Queries the delta time value in seconds or symbols at the selected
marker position.
CALCulate:WLAN:PERRor:MARKer<x>:DELTa:Y? Queries the vertical delta value for the points trace at the selected
marker position.
CALCulate:WLAN:PERRor:MARKer<x>:FREQuency Sets or queries the frequency value at the selected marker position.
CALCulate:WLAN:PERRor:MARKer<x>:TIME Sets the time value (offset) at the selected marker position.
CALCulate:WLAN:PERRor:MARKer<x>:VALue? Queries the Phase Error value at the selected marker position.
Table continued…
42
Page 43
Syntax and Commands
Command Description
CALCulate:WLAN:PVTime:MARKer<x>:DELTa:X? Returns the delta time value at the selected marker position.
CALCulate:WLAN:PVTime:MARKer<x>:DELTa:Y? Queries the vertical delta value for the points trace at the selected
marker position.
CALCulate:WLAN:PVTime:MARKer<x>:MAXimum Positions the specified marker at the maximum point.
CALCulate:WLAN:PVTime:MARKer<x>:PEAK:HIGHer Moves the specified marker to the next peak higher in amplitude.
CALCulate:WLAN:PVTime:MARKer<x>:PEAK:LEFT Moves the specified marker to the next peak on the left.
CALCulate:WLAN:PVTime:MARKer<x>:PEAK:LOWer Moves the marker to the next peak lower in amplitude.
CALCulate:WLAN:PVTime:MARKer<x>:PEAK:RIGHt Moves the marker to the next peak to the right.
CALCulate:WLAN:PVTime:MARKer<x>:X Sets or queries the value of the horizontal position for the selected
marker
CALCulate:WLAN:PVTime:MARKer<x>:Y? Returns the amplitude at the selected marker position.
CALCulate:WLAN:TABLe:MARKer<x>:FREQuency Assigns or queries the frequency value of the marker.
CALCulate:WLAN:TABLe:MARKer<x>:TIME Sets or queries the vertical value at the selected marker position.
CALCulate:WLAN:TABLe:MARKer<x>:VALue? Queries the decoded symbol value at the selected marker position.
CALCulate:LTE subgroup
CALCulate:LTE:ACLR:MARKer:<x>PEAK:HIGHer Moves the specified marker to the next peak higher in amplitude on
the trace.
CALCulate:LTE:ACLR:MARKer<x>:DELTa:X? Returns the frequency of the specified delta marker on the trace.
CALCulate:LTE:ACLR:MARKer<x>:DELTa:Y? Returns the amplitude for the specified delta marker on the trace.
CALCulate:LTE:ACLR:MARKer<x>:MAXimum Positions the specified marker at the highest peak on the trace.
CALCulate:LTE:ACLR:MARKer<x>:PEAK:LEFT Moves the selected marker to the next peak to the left on the trace.
CALCulate:LTE:ACLR:MARKer<x>:PEAK:LOWer
Moves the selected marker to the next peak lower in amplitude on
the trace.
CALCulate:LTE:ACLR:MARKer<x>:PEAK:RIGHt Moves the selected marker to the next peak to the right on the
trace.
CALCulate:LTE:ACLR:MARKer<x>:SET:CENTer Moves the specified marker to the center frequency.
CALCulate:LTE:ACLR:MARKer<x>:X Sets or queries the horizontal position of the selected marker on the
trace.
CALCulate:LTE:ACLR:MARKer<x>:Y? Queries the amplitude of the selected marker on the trace.
CALCulate:LTE:CHSPectrum:MARKer<x>:DELTa:X? Returns the frequency of the specified delta marker on the trace.
CALCulate:LTE:CHSPectrum:MARKer<x>:DELTa:Y? Returns the amplitude for the specified delta marker on the trace.
CALCulate:LTE:CHSPectrum:MARKer<x>:MAXimum Positions the marker at the highest peak on the trace.
CALCulate:LTE:CHSPectrum:MARKer<x>:PEAK:LEFT Moves the selected marker to the next peak to the left on the trace.
CALCulate:LTE:CHSPectrum:MARKer<x>:PEAK:RIGHt Moves the selected marker to the next peak to the right on the
trace.
CALCulate:LTE:CHSPectrum:MARKer<x>:X Sets or queries the horizontal position of the selected marker on the
trace.
CALCulate:LTE:CHSPectrum:MARKer<x>:Y? Queries the amplitude of the selected marker on the trace.
CALCulate:LTE:CONSte:MARKer<x>:FREQuency Sets or returns the subcarrier number of the LTE symbol.
Table continued…
SignalVu-PC Vector Analysis Software Programmer Manual 43
Page 44
Syntax and Commands
Command Description
CALCulate:LTE:CONSte:MARKer<x>:MAGNitude? Queries the marker magnitude of the selected marker.
CALCulate:LTE:CONSte:MARKer<x>:PHASe? Queries the phase readout of the selected marker.
CALCulate:LTE:CONSte:MARKer<x>:TIME Sets or queries the X position (Symbol Value) of the selected
marker.
CALCulate:LTE:CONSte:MARKer<x>:TYPE? Queries the data type of the selected marker as PSS or SSS.
CALCulate:LTE:PVTime:MARKer:<x>PEAK:HIGHer Moves the specified marker to the next peak higher in amplitude on
the trace.
CALCulate:LTE:PVTime:MARKer<x>:DELTa:X? Returns the frequency of the specified delta marker on the trace.
CALCulate:LTE:PVTime:MARKer<x>:DELTa:Y? Returns the amplitude for the specified delta marker on the trace.
CALCulate:LTE:PVTime:MARKer<x>:MAXimum Positions the specified marker at the highest peak on the trace.
CALCulate:LTE:PVTime:MARKer<x>:PEAK:LEFT Moves the selected marker to the next peak to the left on the trace.
CALCulate:LTE:PVTime:MARKer<x>:PEAK:LOWer Moves the selected marker to the next peak lower in amplitude on
the trace.
CALCulate:LTE:PVTime:MARKer<x>:PEAK:RIGHt Moves the selected marker to the next peak to the right on the
trace.
CALCulate:LTE:PVTime:MARKer<x>:X Sets or queries the horizontal position of the selected marker on the
trace.
CALCulate:LTE:PVTime:MARKer<x>:Y? Queries the amplitude of the selected marker on the trace.
CALCulate:NOISe:YFACtor:MARKer<x>:PEAK:HIGHer? Places the selected marker at the next highest peak on the trace.
CALCulate:PULSe:CUMulative:HISTogram[:MEASview<y>]:INDicat
or:X
CALCulate:PULSe:CUMulative:HISTogram[:MEASview<y>]:INDicat
or:Y?
CALCulate:PULSe:OGRAm[:MEASview<y>]:MARKer<x>:FVTime:D
ELTa:X?
CALCulate:PULSe:OGRAm[:MEASview<y>]:MARKer<x>:FVTime:D
ELTa:Y?
CALCulate:PULSe:OGRAm[:MEASview<y>]:MARKer<x>:FVTime:
MAXimum
CALCulate:PULSe:OGRAm[:MEASview<y>]:MARKer<x>:FVTime:X Sets or queries the horizontal position of the selected marker.
CALCulate:PULSe:OGRAm[:MEASview<y>]:MARKer<x>:FVTime:Y Sets or queries the marker amplitude of the selected marker.
CALCulate:PULSe:OGRAm[:MEASview<y>]:MARKer<x>:FVTime:D
ELTa:X?
Sets or queries the horizontal position of the indicator on the trace.
Queries the vertical position value of the indicator on the trace.
Returns the delta marker time for the selected marker.
Returns the delta marker amplitude for the selected marker.
Moves the selected marker to the highest peak on the trace.
Returns the delta marker time for the selected marker.
Marker mnemonics
Up to five markers can be used. In commands, these are named MARKer<x>,where <x> can be 0, 1, 2, 3, or 4 as shown in the following
table.
Table 13: Marker mnemonics
Mnemonic Description
MARKer0 Reference marker (MR)
Table continued…
44
Page 45
Syntax and Commands
Mnemonic Description
MARKer1 Marker 1 (M1)
MARKer2 Marker 2 (M2)
MARKer3 Marker 3 (M3)
MARKer4 Marker 4 (M4)
Note:
If you omit the numeric suffix, the marker control defaults to Marker 1.
Before operating the marker, you have to enable it using the CALCulate basic commands.
If you attempt to use a marker other than above in a CALCulate command, the suffix error (error code -130) will occur.
Calibration commands
Use the CALibration commands to control the external correction. See the Index for commands not listed in the following table.
Not all of these commands apply to SignalVu-PC and connected instruments. See the individual command descriptions for details.
Table 14: Calibration commands
Command Description
CALibration:ABORt Aborts any actions related to the alignments in progress.
CALibration:TXGain:ABORt Cancels a calibration for the Transmission Gain measurement.
CALibration:TXGain[:ALL] Performs a calibration using the current settings for the Transmission Gain
measurement.
CALibration:TXGain:FINish? Queries whether or not the calibration is completed for the Transmission Gain
measurement.
CALibration:TXGain:STATe? Queries the calibration state for the Transmission Gain measurement.
CALibration:AUTO Sets or queries whether or not to run alignments automatically.
INPut:CORRection:EXTernal:EDIT<x>:LABel Sets or queries the name of the external loss table.
CALibration:CORRection:EXTernal:EDIT<x>:NEW Creates a new external loss table.
INPut:CORRection:EXTernal:EDIT<x>:STATe Sets or queries whether to enable or disable the external loss table.
INPut:CORRection:EXTernal:GAIN[:MAGNitude] Sets or queries the external gain value.
CALibration:CORRection:EXTernal:PROBe:CONNect?Sets or queries whether to enable or disable the external gain value.
CALibration:CORRection:EXTernal:PROBe:CONNect?Queries whether the external probe is connected to the analyzer or not.
CALibration:CORRection:EXTernal:PROBe[:MAGNitu
de]?
CALibration:CORRection:EXTernal:PROBe:STATe Determines whether to correct data for the external probe attenuation.
CALibration:CORRection:EXTernal:TYPE Selects data type to use when applying the external loss table.
Queries the external probe attenuation.
SignalVu-PC Vector Analysis Software Programmer Manual 45
Page 46
Syntax and Commands
Display commands
Use the DISPlay commands to control the display of measurement waveforms and results on the screen. See the Index for commands not
listed in the following table.
Not all of these commands apply to SignalVu-PC and connected instruments. See the individual command descriptions for details.
Table 15: Display commands
Command Description
DISPlay TXGain subgroup Transmission Gain measurements
DISPlay:TG:MEASview<y>:DELete TXGain Removes the Transmission Gain display icon from the Selected
displays filed of the Selected Displays window.
DISPlay:TG:MEASview<y>:NEW TXGain Opens a new Transmission Gain measurement display window.
DISPlay:TG:MEASview<y>:SELect TXGain Selects the Transmission Gain display icon in the Select Display
window and queries if the display is selected or not.
DISPlay:TXGain:MARKer:SHOW:STATe Displays or hides the marker readout, but not the marker itself, on
the graph area.
DISPlay:TXGain[:SCALe]:AUTO Automatically rescales the horizontal and vertical scale.
DISPlay:TXGain:WINDow:TRACe:GRATicule:GRID:STATe Displays or hides the graticule grid in the display. Queries whether
the graticule grid is hidden or showing.
DISPlay:TXGain:WINDow:TRACe:POINts:SHOW:STATe Sets to mark each measurement point on the trace.
DISPlay:TXGain:X[:SCALe]:LOG:STATe Sets or queries the display to show the frequency axis in a
logarithmic scale.
DISPlay:TXGain:X[:SCALe]:STARt Sets the Zoom Start frequency.
DISPlay:TXGain:X[:SCALe]:AUTO Resets the scale of the horizontal axis to contain the complete
trace.
DISPlay:TXGain:X[:SCALe]:STOP Sets the Zoom Stop frequency.
DISPlay:TXGain:Y[:SCALe]:BOTTom Sets or queries the bottom of the vertical position of the display.
DISPlay:TXGain:Y[:SCALe]:PDIVision Sets or queries the vertical scale (per division) of the graph.
DISPlay:TXGain:Y[:SCALe]:POSition Sets or queries the vertical position of the trace.
DISPlay:TXGain:Y[:SCALe]:TOP Sets or queries the top of the vertical scale.
DISPlay:TXGain:Y[:SCALe]:AUTO Automatically scales the plot vertically.
DISPlay:TXGain:Y[:SCALe] Sets or queries the vertical scale value in dB.
DISPlay Noise subgroup Noise Figure and Gain measurements
DISPlay:WINDow:ACTive:MEASurement? Queries the active measurement views.
DISPlay Bluetooth subgroup Bluetooth measurements
DISPlay:BIBEmissions:MARKer<x>:SHOW:STATe Sets or queries to show or hide the readout for the selected marker.
DISPlay:BIBEmissions:PLEVel:SHOW:STATe Sets or queries to show or hide the power levels
DISPlay:BIBEmissions:RESet:SCALe Resets the horizontal and vertical scale to the default values.
DISPlay:BIBEmissions:WINDow:TRACe:GRATicule:GRID:STATe Sets or queries the graticule hidden or showing state.
DISPlay:BIBEmissions:X[:SCALe] Sets or queries the horizontal range of the graph.
Table continued…
46
Page 47
Syntax and Commands
Command Description
DISPlay:BIBEmissions:X[:SCALe]:AUTO Rescales the horizontal axis automatically to fit the waveform to the
screen in the Bluetooth InBand Emission view.
DISPlay:BIBEmissions:X[:SCALe]:OFFSet Sets or queries the center frequency.
DISPlay:BIBEmissions:Y[:SCALe] Sets or queries the vertical range of the graph.
DISPlay:BIBEmissions:Y[:SCALe]:AUTO Rescales the vertical axis automatically to fit the waveform to the
screen in the Bluetooth InBand Emission view.
DISPlay:BIBEmissions:Y[:SCALe]:OFFSet Sets or queries the vertical offset.
DISPlay:BLUEtooth:CONSte:TRACe:GRATicule:GRID:STATe Sets or queries the display state of graticule grid.
DISPlay:BLUEtooth:CONSte:WINDow:TRACe:GRATicule:GRID:ST
ATe
DISPlay:BLUEtooth:EDIagram:WINDow:TRACe:GRATicule:GRID:S
TATe
DISPlay:BLUEtooth:EDIagram:Y[:SCALe] Sets or queries the vertical range.
DISPlay:BLUEtooth:EDIagram:Y[:SCALe]:AUTO Sets the vertical scale automatically to fit the waveform in the
DISPlay:BLUEtooth:EDIagram:Y[:SCALe]:OFFSet Sets or queries the vertical offset (center point of the vertical axis).
DISPlay:BLUEtooth:FDVTime:WINDow:TRACe:GRATicule:GRID:S
TATe
DISPlay:BLUEtooth:FDVTime:Y[:SCALe]:AUTO Rescales the vertical scale automatically to fit the waveform to the
DISPlay:BLUEtooth:FDVTime:Y[:SCALe]:OFFSet Sets or queries the vertical offset (center point of the vertical axis).
DISPlay:BLUEtooth:MEASview<y>:DELete Deletes the specified Bluetooth analysis view.
DISPlay:BLUEtooth:MEASview<y>:NEW Displays a new measurement view for Bluetooth measurements.
DISPlay:BLUEtooth:MEASview<y>:SELect Selects a measurement view on the screen in the Bluetooth
DISPlay:BOBW:SELected:BANDwidth Sets or queries the bandwidth to measure in the Bluetooth 20 dB
DISPlay:DPX:WINDow:TRACe:GRATicule:GRID:STATe Determines whether to show or hide the graticule grid on the DPX
DISPlay:NOISe:FIGure[:SCALe]:AUTO Automatically scales the graph.
DISPlay:NOISe:FIGure:WINDow:TRACe:GRATicule:GRID:STATe Sets or queries the graticule state to on (showing) or off (hidden).
DISPlay:NOISe:FIGure:WINDow:TRACe:LEGend:STATe Sets or queries the trace legend state to on (showing) or off
DISPlay:NOISe:FIGure:WINDow:TRACe:MEASpoints:STATe Sets or queries the measurement points state to on (showing) or off
DISPlay:NOISe:FIGure:X:AUTO Automatically sets the horizontal scale of the graph.
DISPlay:NOISe:FIGure:X:OFFSet Sets or queries the center frequency (offset).
DISPlay:NOISe:FIGure:X[:SCALe] Sets or queries the horizontal scale of the display.
DISPlay:NOISe:FIGure:Y:AUTO Automatically sets the vertical scale of the graph.
Table continued…
Sets or queries whether to show or hide the graticule grid on the
screen in the display.
Sets or queries graticule grid hidden or showing state in the
Bluetooth eye diagram display.
Bluetooth eye diagram.
Sets or queries graticule grid hidden or showing state in the Freq
Dev vs Time display.
screen.
measurements.The query command returns the currently selected
view.
BW view.
Spectrum display..
(hidden).
(hidden).
SignalVu-PC Vector Analysis Software Programmer Manual 47
Page 48
Syntax and Commands
Command Description
DISPlay:NOISe:FIGure:Y:AUTO:STATe Sets the state of the automatic vertical scale and position of the
graph to on or off. The query form of the command returns the
current state.
DISPlay:NOISe:FIGure:Y:PDIVision Sets or queries the distance between graticule lines on the display.
DISPlay:NOISe:FIGure:Y:POSition Sets or queries the vertical position of the display.
DISPlay:NOISe:FIGure:Y:SCALe Sets or queries the vertical scale of the display.
DISPlay:NOISe:FIGure:Y:SCALe:LINear:STATe Sets or queries whether the linear units are shown (on) or not
shown (off) on the display.
DISPlay:NOISe:GAIN[:SCALe]:AUTO Automatically scales the graph.
DISPlay:NOISe:GAIN:WINDow:TRACe:GRATicule:GRID:STATe Sets or queries the graticule state to on (showing) or off (hidden).
DISPlay:NOISe:GAIN:WINDow:TRACe:LEGend:STATe Sets or queries the trace legend state to on (showing) or off
(hidden).
DISPlay:NOISe:GAIN:WINDow:TRACe:MEASPoints:STATe Sets or queries the measurement points state to on (showing) or off
(hidden).
DISPlay:NOISe:GAIN:X:AUTO Automatically sets the horizontal scale of the display.
DISPlay:NOISe:GAIN:X:OFFSet Sets or queries the center frequency (offset).
DISPlay:NOISe:GAIN:X:SCALe Sets or queries the horizontal scale of the display.
DISPlay:NOISe:GAIN:Y:AUTO Automatically sets the vertical scale of the graph.
DISPlay:NOISe:GAIN:Y:AUTO:STATe Sets or queries the state of the automatic vertical scale and position
of the graph to on or off.
DISPlay:NOISe:GAIN:Y:PDIVision Sets or queries the distance between graticule lines on the display.
DISPlay:NOISe:GAIN:Y:POSition Sets or queries the vertical position of the display.
DISPlay:NOISe:GAIN:Y:SCALe Sets or queries the vertical scale of the display.
DISPlay:NOISe:MEASview<y>:DELete Deletes the selected Noise and Gain measurement view.
DISPlay:NOISe:MEASview<y>:NEW Displays a new Noise and Gain measurement view.
DISPlay:NOISe:MEASview<y>:SELect Selects a noise measurement view. The query command returns the
currently selected view.
DISPlay:NOISe:POWer:LINear:STATe Sets or queries whether the linear units are shown (on) or not
shown (off) on the Noise Table display.
DISPlay:NOISe:TEMPerature[:SCALe]:AUTO Automatically scales the graph.
DISPlay:NOISe:TEMPerature:WINDow:TRACe:GRATicule:GRID:S
TATe
DISPlay:NOISe:TEMPerature:WINDow:TRACe:LEGend:STATe Sets or queries the trace legend state to on (showing) or off
DISPlay:NOISe:TEMPerature:WINDow:TRACe:MEASPoints:STATe Sets or queries the measurement points state to on (showing) or off
DISPlay:NOISe:TEMPerature:X:AUTO Automatically sets the horizontal scale of the graph.
DISPlay:NOISe:TEMPerature:X:OFFSet Sets or queries the center frequency (offset) value.
DISPlay:NOISe:TEMPerature:X[:SCALe] Sets or queries the horizontal scale of the graph.
DISPlay:NOISe:TEMPerature:X:STARt Sets or queries the Start Frequency value.
Table continued…
Sets or queries the graticule state to on (showing) or off (hidden).
(hidden).
(hidden).
48
Page 49
Syntax and Commands
Command Description
DISPlay:NOISe:TEMPerature:X:STOP Sets or queries the Stop Frequency value.
DISPlay:NOISe:TEMPerature:Y:AUTO Automatically sets the vertical scale of the graph.
DISPlay:NOISe:TEMPerature:Y:AUTO:STATe Sets or queries the state of the automatic vertical scale and position
of the graph to on or off.
DISPlay:NOISe:TEMPerature:Y:PDIVision Sets or queries the distance between graticule lines on the display.
DISPlay:NOISe:TEMPerature:Y:POSition Sets or queries the vertical position of the graph.
DISPlay:NOISe:TEMPerature:Y:SCALe Sets or queries the vertical scale of the graph.
DISPlay:NOISe:UNCERTainty:RESult:GAIN? Queries the gain computed uncertainty value.
DISPlay:NOISe:UNCERTainty:RESult:NFIGure? Queries the noise figure computed uncertainty value.
DISPlay:NOISe:YFACtor[:SCALe]:AUTO Automatically scales the Y Factor graph.
DISPlay:NOISe:YFACtor:WINDow:TRACe:GRATicule:GRID:STATe Sets or queries the graticule state to on (showing) or off (hidden).
DISPlay:NOISe:YFACtor:WINDow:TRACe:LEGend:STATe Sets or queries the trace legend state to on (showing) or off
(hidden).
DISPlay:NOISe:YFACtor:WINDow:TRACe:MEASPoints:STATe Sets or queries the measurement points state to on (showing) or off
(hidden).
DISPlay:NOISe:YFACtor:X:AUTO Automatically sets the horizontal scale.
DISPlay:NOISe:YFACtor:X:OFFSet Sets or queries the center frequency (offset).
DISPlay:NOISe:YFACtor:X[:SCALe] Sets or queries the horizontal scale.
DISPlay:NOISe:YFACtor:X:STARt Sets or queries the Start Frequency value.
DISPlay:NOISe:YFACtor:X:STOP Sets or queries the Stop Frequency value.
DISPlay:NOISe:YFACtor:Y:AUTO Automatically sets the vertical scale of the graph.
DISPlay:NOISe:YFACtor:Y:AUTO:STATe Sets or queries the automatic vertical scale and position of the
graph setting to on or off.
DISPlay:NOISe:YFACtor:Y:PDIVision Sets or queries the distance between graticule lines on the display
in dB.
DISPlay:NOISe:YFACtor:Y:POSition Sets or queries the vertical position.
DISPlay:NOISe:YFACtor:Y:SCALe Sets or queries the vertical scale.
DISPlay:P25:CONSte:WINDow:TRACe:GRATicule:GRID:STATe Sets or queries to show or hide the graticule grid on the screen.
DISPlay:P25:EDIagram:WINDow:TRACe:GRATicule:GRID:STATe Sets or queries to show or hide the graticule grid on the screen.
DISPlay:P25:EDIagram:Y[:SCALe] Sets or queries the vertical scale.
DISPlay:P25:EDIagram:Y[:SCALe]:AUTO Sets the vertical scale automatically to fit the waveform to the
screen.
DISPlay:P25:EDIagram:Y[:SCALe]:OFFSet Sets or queries the vertical offset (center point of the vertical axis).
DISPlay:P25:MEASview:DELete Deletes the specified P25 measurement display.
DISPlay:P25:MEASview:NEW Displays a new P25 measurement view.
DISPlay:P25:MEASview:SELect Selects a P25 measurement display. The query form returns the
currently selected display.
DISPlay:P25:PVTime:BURSt:X[:SCALe] Sets or queries the value of the scale (width) value, in seconds,
when using horizontal Full Burst view.
Table continued…
SignalVu-PC Vector Analysis Software Programmer Manual 49
Page 50
Syntax and Commands
Command Description
DISPlay:P25:PVTime:BURSt:X[:SCALe]:AUTO Automatically sets the starting time (position) and scale (width)
values for the best display in the horizontal Full Burst view.
DISPlay:P25:PVTime:BURSt:X[:SCALe]:OFFSet Sets or queries the starting time (position) value, in seconds, when
using the horizontal Full Burst view.
DISPlay:P25:PVTime:BURSt:X[:SCALe]:RESet Resets the starting time (position) and scale (width) values for the
horizontal Full Burst view.
DISPlay:P25:PVTime:FALL:X[:SCALe] Sets or queries the scale (width) value, in seconds, when using the
horizontal Falling Edge view.
DISPlay:P25:PVTime:FALL:X[:SCALe]:AUTO Automatically sets the starting time (position) and scale (width)
values for the best display in the horizontal Falling Edge view.
DISPlay:P25:PVTime:FALL:X[:SCALe]:OFFSet Sets or queries the value for the starting time (offset) of the graph,
in seconds, when using the horizontal Falling Edge view.
DISPlay:P25:PVTime:FALL:X[:SCALe]:RESet Resets the starting time (position) and scale (width) values for the
horizontal Falling Edge view.
DISPlay:P25:PVTime:MARKer:SHOW:STATe Shows or hides the marker readout.
DISPlay:P25:PVTime:RISE:X[:SCALe] Sets or queries the scale (width) value, in seconds, for the P25
Power vs. Time display when using the horizontal Rising Edge view.
DISPlay:P25:PVTime:RISE:X[:SCALe]:AUTO Sets the scale (width) value, in seconds, to automatic.
DISPlay:P25:PVTime:RISE:X[:SCALe]:OFFSet Sets or queries the starting time value (offset), in seconds, for the
P25 Power vs. Time display when using the horizontal Rising Edge
view.
DISPlay:P25:PVTime:RISE:X[:SCALe]:RESet Resets the starting time (position) and scale (width) values for the
horizontal Rising Edge view.
DISPlay:P25:PVTime:WINDow:SELect:PLOT Sets or queries which view to use: Full Burst, Rising Edge, or
Falling Edge.
DISPlay:P25:PVTime:WINDow:TRACe:GRATicule:GRID:STATe Sets or queries the graticule state to on (showing) or off (hidden).
DISPlay:P25:PVTime:Y[:SCALe] Sets or queries the vertical scale value.
DISPlay:P25:PVTime:Y[:SCALe]:AUTO Automatically selects the vertical scale and position values.
DISPlay:P25:PVTime:Y[:SCALe]:OFFSet Sets or queries the value of the vertical offset (top edge of the
vertical axis).
DISPlay:P25:PVTime:Y[:SCALe]:PDIVision Sets or queries the value of the vertical scale for the P25 Power vs.
Time display.
DISPlay:P25:RADix Set or queries the symbol radix for the P25 Symbol Table display.
DISPlay:TOVerview[:MEASview<y>]:WINDow:NAVigator:STATe Sets or queries whether the navigator view of the Time Overview
display is on or off.
DISPlay:TOVerview[:MEASview<y>]:WINDow:TIME:MODE Sets or queries the type of time analysis to be performed.
DISPlay:TOVerview[:MEASview<y>]:WINDow:TRACe:LEGend:STATeSets or queries the trace legend state to on (showing) or off
(hidden).
DISPlay basic command subgroup General window control
DISPlay:WINDow:COLor:SCHeme Sets or queries the color scheme for traces and background.
DISPlay:WINDow:OPTimized:MEASurement? Queries the measurement views that are optimized.
Table continued…
50
Page 51
Syntax and Commands
Command Description
DISPlay:ACPower subgroup Channel power and ACPR measurement
DISPlay:ACPower:MARKer:SHOW:STATe Determines whether to show the readout for the selected marker.
DISPlay:ACPower:PLEVel:SHOW:STATe Determines whether to show the power levels.
DISPlay:ACPower:RESet:SCALe Resets the horizontal and vertical scale to the default values.
DISPlay:ACPower:WINDow:TRACe:GRATicule:GRID:STATe Determines whether to show the graticule grid on screen.
DISPlay:ACPower:X[:SCALe] Sets or queries the horizontal range.
DISPlay:ACPower:X[:SCALe]:AUTO Rescales the horizontal axis automatically.
DISPlay:ACPower:X[:SCALe]:OFFSet Sets or queries the minimum horizontal value (left edge).
DISPlay:ACPower:Y[:SCALe] Sets or queries the vertical range.
DISPlay:ACPower:Y[:SCALe]:AUTO Rescales the vertical axis automatically.
DISPlay:ACPower:Y[:SCALe]:OFFSet Sets or queries the vertical offset.
DISPlay:ADEMod subgroup (Option 21 only) General purpose analog demodulation measurements
DISPlay:ADEMod:MEASview<y>:DELete Deletes the measurement view.
DISPlay:ADEMod:MEASview<y>:NEW Displays a new measurement view.
DISPlay:ADEMod:MEASview<y>:SELect Sets or queries the measurement view.
DISPlay:{AM|FM|PM} subgroup (Option 21 only) AM/FM/PM measurement
DISPlay:{AM|FM|PM}:MARKer:SHOW:STATe Determines whether to show the readout for the selected marker.
DISPlay:{AM|FM|PM}:WINDow:TRACe:GRATicule:GRID:STATe Determines whether to show the graticule grid on screen.
DISPlay:{AM|FM|PM}:X:RSCale Rescales the horizontal axis automatically.
DISPlay:{AM|FM|PM}:X[:SCALe]:AUTO Sets the horizontal scale automatically.
DISPlay:{AM|FM|PM}:X[:SCALe]:FULL Sets or queries the horizontal scale.
DISPlay:{AM|FM|PM}:X[:SCALe]:OFFSet Sets or queries the minimum horizontal value (left edge).
DISPlay:{AM|FM|PM}:Y:RSCale Rescales the vertical axis automatically.
DISPlay:{AM|FM|PM}:Y[:SCALe] Sets or queries the vertical scale.
DISPlay:{AM|FM|PM}:Y[:SCALe]:OFFSet Sets or queries the vertical offset.
DISPlay:AUDio subgroup Audio measurements
DISPlay:AUDio:MEASview<y>:DELete Deletes the specified audio analysis view.
DISPlay:AUDio:MEASview<y>:NEW Displays a new audio analysis view.
DISPlay:AUDio:MEASview<y>:SELect Selects an audio analysis view on the screen.
DISPlay:AUDio:SPECtrum:FREQuency:[SCALe]:STARt Sets or queries the start frequency (left edge) of the audio spectrum
graph.
DISPlay:AUDio:SPECtrum:FREQuency:[SCALe]:STOP Sets or queries the stop frequency (right edge) of the audio
spectrum graph.
DISPlay:AUDio:SPECtrum:FREQuency:AUTO Rescales the horizontal axis automatically to fit the waveform to the
screen in the audio spectrum view.
DISPlay:AUDio:SPECtrum:MARKer:SHOW:STATe Determines whether to show or hide the readouts for the selected
marker in the audio spectrum view.
Table continued…
SignalVu-PC Vector Analysis Software Programmer Manual 51
Page 52
Syntax and Commands
Command Description
DISPlay:AUDio:SPECtrum:RESet:SCALe Resets the horizontal and vertical scales in the audio spectrum
view.
DISPlay:AUDio:SPECtrum:SCALe:LOG:STATe Determines whether or not to set the horizontal axis logarithmic in
the audio spectrum view.
DISPlay:AUDio:SPECtrum:SHOW:NHARmonic:THReshold Sets or queries the appearance of the non-harmonic threshold in
the audio spectrum view.
DISPlay:AUDio:SPECtrum:TABLe:SHOW:STATe Determines whether to show or hide the results table in the audio
spectrum view.
DISPlay:AUDio:SPECtrum:WINDow:TRACe:GRATicule:GRID:STATeDetermines whether to show or hide the graticule grid on the
screen.
DISPlay:AUDio:SPECtrum:Y:[SCALe] Sets or queries the vertical scale in the audio spectrum view.
DISPlay:AUDio:SPECtrum:Y:[SCALe]:AUTO Rescales the vertical axis automatically in the audio spectrum view.
DISPlay:AUDio:SPECtrum:Y:[SCALe]:OFFSet Sets or queries the vertical position (offset) in the audio spectrum
view.
DISPlay:AVTime subgroup Amplitude versus Time measurement
DISPlay:AVTime[:MEASview<y>]:LEGend:STATe Shows or hides the trace legend in the amplitude versus time view.
DISPlay:AVTime[:MEASview<y>]:MARKer:SHOW:STATe Determines whether to show the readout for the selected marker.
DISPlay:AVTime[:MEASview<y>]:RESet Resets the horizontal and vertical scale to the default values.
DISPlay:AVTime[:MEASview<y>]:TRIGger:LEVel:STATe Determines whether to show the power trigger level line on screen.
DISPlay:AVTime[:MEASview<y>]:WINDow:TRACe:GRATicule:GRI
D:STATe
DISPlay:AVTime[:MEASview<y>]:X:RSCale Rescales the horizontal axis automatically.
DISPlay:AVTime[:MEASview<y>]:X[:SCALe]:AUTO Sets the horizontal scale automatically.
DISPlay:AVTime[:MEASview<y>]:X[:SCALe]:AUTO:STATe Determines whether to set the horizontal scale automatically or
DISPlay:AVTime[:MEASview<y>]:X[:SCALe]:FULL Sets or queries the horizontal scale.
DISPlay:AVTime[:MEASview<y>]:X[:SCALe]:MAXimum? Queries the upper limit of the horizontal scale setting range.
DISPlay:AVTime[:MEASview<y>]:X[:SCALe]:MINimum? Queries the lower limit of the horizontal scale setting range.
DISPlay:AVTime[:MEASview<y>]:X[:SCALe]:OFFSet Sets or queries the minimum horizontal value (left edge).
DISPlay:AVTime[:MEASview<y>]:X[:SCALe]:OFFSet:MAXimum? Queries the upper limit of the horizontal offset setting range.
DISPlay:AVTime[:MEASview<y>]:X[:SCALe]:OFFSet:MINimum? Queries the lower limit of the horizontal offset setting range.
DISPlay:AVTime[:MEASview<y>]:Y:RSCale Rescales the vertical axis automatically.
DISPlay:AVTime[:MEASview<y>]:Y[:SCALe]:FULL Sets or queries the vertical scale.
DISPlay:AVTime[:MEASview<y>]:Y[:SCALe]:OFFSet Sets or queries the vertical offset.
DISPlay:CONSte subgroup (Option 21 only) Constellation measurement
DISPlay:CONSte:MPHase Sets or queries the phase multiplication constant for a CPM signal.
DISPlay:CONSte:WINDow:TRACe:GRATicule:GRID:STATe Sets or queries whether to show the graticule grid on the screen.
DISPlay:DDEMod subgroup (Option 21 only) General purpose digital modulation measurements
DISPlay:DDEMod:MEASview:DELete Deletes the measurement view.
Table continued…
Determines whether to show the graticule grid on screen.
manually.
52
Page 53
Syntax and Commands
Command Description
DISPlay:DDEMod:MEASview:NEW Displays a new measurement view.
DISPlay:DDEMod:MEASview:SELect Sets or queries the measurement view.
DISPlay:DDEMod:RADix Sets or queries the base of symbols.
DISPlay:DDEMod:X[:SCALe] Sets or queries the horizontal scale.
DISPlay:DDEMod:X[:SCALe]:AUTO Sets the horizontal scale automatically.
DISPlay:DDEMod:X[:SCALe]:AUTO:STATe Determines whether to set the horizontal scale automatically or
manually.
DISPlay:DDEMod:X[:SCALe]:MAXimum? Queries the upper limit of the horizontal scale setting range.
DISPlay:DDEMod:X[:SCALe]:MINimum? Queries the lower limit of the horizontal scale setting range.
DISPlay:DDEMod:X[:SCALe]:OFFSet Sets or queries the minimum horizontal value (left edge).
DISPlay:DDEMod:X[:SCALe]:OFFSet:MAXimum? Queries the upper limit of the horizontal offset setting range.
DISPlay:DDEMod:X[:SCALe]:OFFSet:MINimum? Queries the lower limit of the horizontal offset setting range.
DISPlay:DDEMod:X[:SCALe]:RESet Presets the horizontal scale to the default value.
DISPlay:DIAGram subgroup (Option 21 only) Eye/Trellis diagram
DISPlay:DIAGram:X[:SCALe] Sets or queries the horizontal range.
DISPlay:DIAGram:X[:SCALe]:RESet Presets the horizontal scale to the default value.
DISPlay:DIQVtime subgroup (Option 21 only) Demodulated I&Q versus Time measurement
DISPlay:DIQVtime:WINDow:TRACe:GRATicule:GRID:STATe Sets or queries whether to show the graticule grid on the screen.
DISPlay:DIQVtime:Y[:SCALe] Sets or queries the vertical scale.
DISPlay:DIQVtime:Y[:SCALe]:AUTO Sets the vertical scale automatically.
DISPlay:DIQVtime:Y[:SCALe]:OFFSet Sets or queries the vertical offset (center point of the vertical axis).
DISPlay:DPX subgroup DPXogram measurement
DISPlay:DPX:DGRam:TIME[:SCALe]:OFFSet:DIVision Sets or queries the DPXogram vertical time offset in divisions.
DISPlay:DPX:DGRam:TIME[:SCALe]:PDIVision Sets or queries the DPXogram vertical time scale per division.
DISPlay:DPX:DGRam:TIME[:SCALe]:RESet Presets the time scale to the default value for the DPXogram
measurement.
DISPlay:DPX:DGRam:TSTamp:STATe Determines whether to display the time stamp readout in the
DPXogram display.
DISPlay:DPX:DGRam:Y[:SCALe]:AUTO Rescales the height axis automatically to fit the waveform to the
screen in the DPXogram display.
DISPlay:DPX:DGRam:Y[:SCALe]:RESet Resets the height scale of the DPXogram display.
DISPlay:DPX:LEGend:STATe Determines whether to show or hide the trace legend on the display.
DISPlay:DPX:PHASe:Y[:SCALe]:AXIS Sets or queries the vertical axis representation.
DISPlay:DPX:PHASe:Y[:SCALe]:AXIS:OFFSet Sets or queries the vertical offset in the DPX Phase view.
DISPlay:DPX:Y[:SCALe]:OFFSet Sets or queries the vertical offset.
DISPlay:DPX:Y[:SCALe]:PDIVision Sets or queries the vertical scale (per division).
DISPlay:DPX:WINDow:TRACe:GRATicule:GRID:STATe Shows or hides the graticule grid on the screen
DISPlay:EDIagram subgroup (Option 21 only) Eye diagram
Table continued…
SignalVu-PC Vector Analysis Software Programmer Manual 53
Page 54
Syntax and Commands
Command Description
DISPlay:EDIagram:WINDow:TRACe:GRATicule:GRID:STATe Sets or queries whether to show the graticule grid on the screen.
DISPlay:EDIagram:Y[:SCALe] Sets or queries the vertical scale.
DISPlay:EDIagram:Y[:SCALe]:AUTO Sets the vertical scale automatically.
DISPlay:EDIagram:Y[:SCALe]:OFFSet Sets or queries the vertical offset (center point of the vertical axis).
DISPlay:EVM subgroup (Option 21 only) EVM versus Time measurement
DISPlay:EVM:WINDow:TRACe:GRATicule:GRID:STATe Sets or queries the graticule grid view state for the EVM view.
DISPlay:EVM:Y[:SCALe] Sets or queries the vertical scale.
DISPlay:EVM:Y[:SCALe]:AUTO Sets the vertical scale automatically.
DISPlay:EVM:Y[:SCALe]:OFFSet Sets or queries the minimum vertical value (bottom edge).
DISPlay:FDVTime subgroup (Option 21 only) Frequency deviation versus Time measurement
DISPlay:FDVTime:WINDow:TRACe:GRATicule:GRID:STATe Sets or queries whether to show the graticule grid on the Frequency
deviation versus Time view.
DISPlay:FDVTime:Y[:SCALe] Sets or queries the vertical range of the Frequency deviation versus
Time graph.
DISPlay:FDVTime:Y[:SCALe]:AUTO Sets the vertical scale automatically.
DISPlay:FDVTime:Y[:SCALe]:OFFSet Sets or queries the vertical offset (center point of the vertical axis).
DISPlay:{FSETtling|PSETtling} subgroup Frequency and Phase Settling measurements
DISPlay:{FSETtling|PSETtling}:MARKer:SHOW:STATe Determines whether to show or hide the readout for the selected
marker in the Frequency or Phase Settling views.
DISPlay:{FSETtling|PSETtling}:TIME:DECimal Sets or queries the number of values to the right of the decimal
point.
DISPlay:{FSETtling|
PSETtling}:WINDow:TRACe:GRATicule:GRID:STATe
DISPlay:{FSETtling|PSETtling}:X[:SCALe] Sets or queries the horizontal scale (full-scale time) of the Settling
DISPlay:{FSETtling|PSETtling}:X[:SCALe]:AUTO Sets the horizontal scale automatically to fit the waveform to the
DISPlay:{FSETtling|PSETtling}:X[:SCALe]:AUTO:STATe Determines whether to set the horizontal scale automatically or
DISPlay:{FSETtling|PSETtling}:X[:SCALe]:MAXimum? Queries the upper limit of the horizontal scale setting range.
DISPlay:{FSETtling|PSETtling}:X[:SCALe]:MINimum? Queries the lower limit of the horizontal scale setting range.
DISPlay:{FSETtling|PSETtling}:X[:SCALe]:OFFSet:MINimum?
Determines whether to show or hide the graticule grid on the
screen.
Time graph.
screen in the Frequency and Phase Settling views.
manually.
Queries the lower limit of the horizontal offset setting range.
DISPlay:{FSETtling|PSETtling}:X[:SCALe]:OFFSet Sets or queries the minimum horizontal value (left edge) of the
Frequency versus Time graph.
DISPlay:{FSETtling|PSETtling}:X[:SCALe]:OFFSet:MAXimum? Queries the upper limit of the horizontal offset setting range.
DISPlay:{FSETtling|PSETtling}:X[:SCALe]:OFFSet:MINimum? Queries the lower limit of the horizontal offset setting range.
DISPlay:{FSETtling|PSETtling}:Y[:SCALe] Sets or queries the vertical range of the Frequency versus Time
graph.
DISPlay:{FSETtling|PSETtling}:Y[:SCALe]:AUTO Sets the vertical scale automatically to fit the waveform to the
screen in the Frequency and Phase Settling views.
Table continued…
54
Page 55
Syntax and Commands
Command Description
DISPlay:{FSETtling|PSETtling}:Y[:SCALe]:OFFSet Sets or queries the vertical offset (the value at the center of the
vertical axis) in the Frequency and Phase Settling graphs.
DISPlay:{FSETtling|PSETtling}:Y[:SCALe]:PDIVision Sets or queries the vertical scale (per division) of the Frequency
and Phase Settling graphs.
DISPlay:FVTime subgroup Frequency versus Time measurement
DISPlay:FVTime[:MEASview<y>]:WINDow:TRACe:GRATicule:GRI
D:STATe
DISPlay:FVTime[:MEASview<y>]:X[:SCALe] Sets or queries the horizontal scale.
DISPlay:FVTime[:MEASview<y>]:X[:SCALe]:AUTO Sets the horizontal scale automatically.
DISPlay:FVTime[:MEASview<y>]:X[:SCALe]:AUTO:STATe Determines whether to set the horizontal scale automatically or
DISPlay:FVTime[:MEASview<y>]:X[:SCALe]:MAXimum? Queries the upper limit of the horizontal scale setting range.
DISPlay:FVTime[:MEASview<y>]:X[:SCALe]:MINimum? Queries the lower limit of the horizontal scale setting range.
DISPlay:FVTime[:MEASview<y>]:X[:SCALe]:OFFSet Sets or queries the minimum horizontal value (left edge).
DISPlay:FVTime[:MEASview<y>]:X[:SCALe]:OFFSet:MAXimum? Queries the upper limit of the horizontal offset setting range.
DISPlay:FVTime[:MEASview<y>]:X[:SCALe]:OFFSet:MINimum? Queries the lower limit of the horizontal offset setting range.
DISPlay:FVTime[:MEASview<y>]:Y[:SCALe] Sets or queries the vertical scale.
DISPlay:FVTime[:MEASview<y>]:Y[:SCALe]:AUTO Sets the vertical scale automatically.
DISPlay:FVTime[:MEASview<y>]:Y[:SCALe]:OFFSet Sets or queries the vertical offset.
DISPlay:GENeral subgroup General signal viewing
DISPlay:GENeral:MEASview<y>:DELete Deletes the measurement view.
DISPlay:GENeral:MEASview<y>[:SOURce<x>]:NEW Displays a new measurement view.
DISPlay:GENeral:MEASview<y>:SELect Sets or queries the measurement view.
DISPlay:GPRF subgroup General purpose RF measurements
DISPlay:GPRF:MEASview:DELete Deletes the measurement view.
DISPlay:GPRF:MEASview[:SOURce<x>]:NEW Displays a new measurement view.
DISPlay:GPRF:MEASview:SELect Sets or queries the measurement view.
DISPlay:IQVTime subgroup RF I&Q versus Time measurement
DISPlay:IQVTime[:MEASview<y>]:WINDow:TRACe:GRATicule:GRI
D:STATe
DISPlay:IQVTime[:MEASview<y>]:X[:SCALe] Sets or queries the horizontal scale.
DISPlay:IQVTime[:MEASview<y>]:X[:SCALe]:AUTO Sets the horizontal scale automatically.
DISPlay:IQVTime[:MEASview<y>]:X[:SCALe]:AUTO:STATe Determines whether to set the horizontal scale automatically or
DISPlay:IQVTime[:MEASview<y>]:X[:SCALe]:MAXimum? Queries the upper limit of the horizontal scale setting range.
DISPlay:IQVTime[:MEASview<y>]:X[:SCALe]:MINimum? Queries the lower limit of the horizontal scale setting range.
DISPlay:IQVTime[:MEASview<y>]:X[:SCALe]:OFFSet Sets or queries the minimum horizontal value (left edge).
DISPlay:IQVTime[:MEASview<y>]:X[:SCALe]:OFFSet:MAXimum? Queries the upper limit of the horizontal offset setting range.
DISPlay:IQVTime[:MEASview<y>]:X[:SCALe]:OFFSet:MINimum? Queries the lower limit of the horizontal offset setting range.
Table continued…
Sets or queries whether to show the graticule grid on the Frequency
versus Time view.
manually.
Sets or queries whether to show the graticule grid on the screen.
manually.
SignalVu-PC Vector Analysis Software Programmer Manual 55
Page 56
Syntax and Commands
Command Description
DISPlay:IQVTime[:MEASview<y>]:Y[:SCALe] Sets or queries the vertical scale.
DISPlay:IQVTime[:MEASview<y>]:Y[:SCALe]:AUTO Sets the vertical scale automatically.
DISPlay:IQVTime[:MEASview<y>]:Y[:SCALe]:OFFSet Sets or queries the vertical offset.
DISPlay:IQVTime[:MEASview<y>]:Y[:SCALe]:RESCale Rescales the vertical scale.
DISPlay:MCPower subgroup MCPR measurement
DISPlay:MCPower:MARKer:SHOW:STATe Determines whether to show the readout for the selected marker.
DISPlay:MCPower:PLEVel:SHOW:STATe Determines whether to show the power levels.
DISPlay:MCPower:RESet:SCALe Resets the horizontal and vertical scale to the default values.
DISPlay:MCPower:WINDow:TRACe:GRATicule:GRID:STATe Determines whether to show the graticule grid on screen.
DISPlay:MCPower:X[:SCALe] Sets or queries the horizontal range.
DISPlay:MCPower:X[:SCALe]:AUTO Rescales the horizontal axis automatically.
DISPlay:MCPower:X[:SCALe]:OFFSet Sets or queries the minimum horizontal value (left edge).
DISPlay:MCPower:Y[:SCALe] Sets or queries the vertical range.
DISPlay:MCPower:Y[:SCALe]:AUTO Rescales the vertical axis automatically.
DISPlay:MCPower:Y[:SCALe]:OFFSet Sets or queries the vertical offset.
DISPlay:MERRor subgroup (Option 21 only) Magnitude error versus Time measurement
DISPlay:MERRor:WINDow:TRACe:GRATicule:GRID:STATe Sets or queries the graticule grid view state for the Magnitude error
versus Time view.
DISPlay:MERRor:Y[:SCALe] Sets or queries the vertical scale.
DISPlay:MERRor:Y[:SCALe]:AUTO Sets the vertical scale automatically.
DISPlay:MERRor:Y[:SCALe]:OFFSet Sets or queries the minimum vertical value (bottom edge).
DISPlay:OBWidth subgroup Occupied Bandwidth measurement
DISPlay:OBWidth:MARKer:SHOW:STATe Determines whether to show the readout for the selected marker.
DISPlay:OBWidth:RESet:SCALe Resets the horizontal and vertical scale to the default values.
DISPlay:OBWidth:SELected:BANDwidth Sets or queries the bandwidth (OBW or x dB BW) to measure.
DISPlay:OBWidth:WINDow:TRACe:GRATicule:GRID:STATe Determines whether to show the graticule grid on screen.
DISPlay:OBWidth:X[:SCALe] Sets or queries the horizontal range.
DISPlay:OBWidth:X[:SCALe]:AUTO Rescales the horizontal axis automatically.
DISPlay:OBWidth:X[:SCALe]:OFFSet Sets or queries the minimum horizontal value (left edge).
DISPlay:OBWidth:Y[:SCALe] Sets or queries the vertical range
DISPlay:OBWidth:Y[:SCALe]:AUTO Rescales the vertical axis automatically.
DISPlay:OBWidth:Y[:SCALe]:OFFSet Sets or queries the vertical offset.
DISPlay:OFDM subgroup OFDM measurements
DISPlay:OFDM:CONSte[:SCALe] Sets or queries the horizontal offset.
DISPlay:OFDM:CONSte:X:OFFSet Sets or queries the vertical offset.
DISPlay:OFDM:CONSte:Y:OFFSet Sets or queries the scale.
DISPlay:OFDM:CRESponse:FREQuency:AUTO Rescales the horizontal axis automatically.
Table continued…
56
Page 57
Syntax and Commands
Command Description
DISPlay:OFDM:CRESponse:FREQuency:OFFSet Sets or queries the frequency offset.
DISPlay:OFDM:CRESponse:MAGNitude:AUTO Sets or queries the horizontal range.
DISPlay:OFDM:CRESponse:MAGNitude:OFFSet Rescales the magnitude automatically.
DISPlay:OFDM:CRESponse:MAGNitude:PDIVision Sets or queries the magnitude offset.
DISPlay:OFDM:CRESponse:PHASe:AUTO Sets or queries the scale (per division) of the magnitude.
DISPlay:OFDM:CRESponse:PHASe:OFFSet Rescales the vertical axis automatically.
DISPlay:OFDM:CRESponse:PHASe[:SCALe] Sets or queries the phase offset.
DISPlay:OFDM:CRESponse:WINDow:SELect:PLOT Sets the vertical scale automatically.
DISPlay:OFDM:CRESponse:WINDow:TRACe:GRATicule:GRID:ST
ATe
DISPlay:OFDM:EVM:FREQuency[:SCALe] Determines whether to show or hide the graticule.
DISPlay:OFDM:EVM:FREQuency:AUTO Sets or queries the horizontal range.
DISPlay:OFDM:EVM:FREQuency:OFFSet Rescales the frequency automatically to fit the waveform to the
DISPlay:OFDM:EVM:MARKer:SHOW:STATe Sets or queries the frequency offset.
DISPlay:OFDM:EVM:TIME[:SCALe] Determines whether to show or hide the readout.
DISPlay:OFDM:EVM:TIME:AUTO Rescales the time automatically to fit the waveform to the screen..
DISPlay:OFDM:EVM:TIME:OFFSet Sets or queries the time offset.
DISPlay:OFDM:EVM:WINDow:SELect:PLOT Sets or queries the plot.
DISPlay:OFDM:EVM:WINDow:TRACe:GRATicule:GRID:STATe Determines whether to show or hide the graticule.
DISPlay:OFDM:EVM:Y[:SCALe] Sets or queries the vertical range.
DISPlay:OFDM:EVM:Y:AUTO Rescales the vertical scale automatically.
DISPlay:OFDM:EVM:Y:OFFSet Sets or queries the vertical offset.
DISPlay:OFDM:FLATness:AUTO Automatically rescales the horizontal and vertical axes for the best
DISPlay:OFDM:FLATness:X:AUTO Rescales the horizontal axis automatically in the OFDM Spectral
DISPlay:OFDM:FLATness:X:OFFSet Sets or queries the value of the offset of the horizontal axis.
DISPlay:OFDM:FLATness:X[:SCALe] Sets or queries the value of the horizontal scale.
DISPlay:OFDM:FLATness:Y:AUTO Rescales the vertical axis scale and position values automatically.
DISPlay:OFDM:FLATness:Y:OFFSet Sets or queries the value of the offset from the center (vertical
DISPlay:OFDM:FLATness:Y[:SCALe] Sets or queries the vertical scale value.
DISPlay:OFDM:MEASview:DELete Deletes the specified OFDM measurement view.
DISPlay:OFDM:MEASview:NEW Creates a new OFDM measurement view.
DISPlay:OFDM:MEASview:SELect Sets or queries the OFDM measurement view.
DISPlay:OFDM:MERRor:FREQuency[:SCALe] Sets or queries the horizontal range.
DISPlay:OFDM:MERRor:FREQuency[:SCALe]:AUTO Rescales the frequency automatically to fit the waveform to the
Table continued…
Sets or queries the plot
screen.
display.
Flatness display.
position).
screen.
SignalVu-PC Vector Analysis Software Programmer Manual 57
Page 58
Syntax and Commands
Command Description
DISPlay:OFDM:MERRor:FREQuency[:SCALe]:OFFSet Sets or queries the frequency offset.
DISPlay:OFDM:MERRor:MARKer:SHOW:STATe Determines whether to show or hide the readout for the selected
marker.
DISPlay:OFDM:MERRor:TIME[:SCALe] Sets or queries the time scale.
DISPlay:OFDM:MERRor:TIME[:SCALe]:AUTO Rescales the time automatically to fit the waveform to the screen.
DISPlay:OFDM:MERRor:TIME[:SCALe]:OFFSet Sets or queries the time offset.
DISPlay:OFDM:MERRor:WINDow:SELect:PLOT Sets or queries the plot.
DISPlay:OFDM:MERRor:WINDow:TRACe:GRATicule:GRID:STATe Determines whether to show or hide the graticule.
DISPlay:OFDM:MERRor:Y[:SCALe] Sets or queries the vertical range.
DISPlay:OFDM:MERRor:Y:AUTO Rescales the vertical scale automatically to fit the waveform.
DISPlay:OFDM:MERRor:Y:OFFSet Sets or queries the vertical offset.
DISPlay:OFDM:PERRor:FREQuency[:SCALe] Sets or queries the horizontal range.
DISPlay:OFDM:PERRor:FREQuency[:SCALe]:AUTO Rescales the frequency automatically to fit the waveform to the
screen.
DISPlay:OFDM:PERRor:FREQuency[:SCALe]:OFFSet Sets or queries the frequency offset.
DISPlay:OFDM:PERRor:MARKer:SHOW:STATe Determines whether to show or hide the readout for the selected
marker.
DISPlay:OFDM:PERRor:TIME[:SCALe] Sets or queries the time scale.
DISPlay:OFDM:PERRor:TIME[:SCALe]:AUTO Rescales the time automatically to fit the waveform to the screen.
DISPlay:OFDM:PERRor:TIME[:SCALe]:OFFSet Sets or queries the time offset.
DISPlay:OFDM:PERRor:WINDow:SELect:PLOT Sets or queries the plot.
DISPlay:OFDM:PERRor:WINDow:TRACe:GRATicule:GRID:STATe Determines whether to show or hide the graticule.
DISPlay:OFDM:PERRor:Y[:SCALe] Sets or queries the vertical range.
DISPlay:OFDM:PERRor:Y:AUTO Rescales the vertical scale automatically to fit the waveform.
DISPlay:OFDM:PERRor:Y:OFFSet Sets or queries the vertical offset.
DISPlay:OFDM:POWer:FREQuency[:AUTO] Rescales the frequency automatically to fit the waveform to the
screen.
DISPlay:OFDM:POWer:FREQuency[:OFFSet] Sets or queries the frequency offset.
DISPlay:OFDM:POWer:FREQuency[:SCALe] Sets or queries the horizontal range.
DISPlay:OFDM:POWer:MARKer:SHOW:STATe Determines whether to show or hide the readout for the selected
marker.
DISPlay:OFDM:POWer:TIME[:AUTO Rescales the time automatically to fit the waveform to the screen.
DISPlay:OFDM:POWer:TIME:OFFSet Sets or queries the time offset.
DISPlay:OFDM:POWer:TIME[:SCALe] Sets or queries the time scale.
DISPlay:OFDM:POWer:WINDow:SELect:PLOT Sets or queries the plot.
DISPlay:OFDM:POWer:WINDow:TRACe:GRATicule:GRID:STATe Determines whether to show or hide the graticule.
DISPlay:OFDM:POWer:Y:AUTO Rescales the vertical scale automatically to fit the waveform.
DISPlay:OFDM:POWer:Y:OFFSet Sets or queries the vertical offset.
Table continued…
58
Page 59
Syntax and Commands
Command Description
DISPlay:OFDM:POWer:Y[:SCALe] Sets or queries the vertical range.
DISPlay:PERRor subgroup (Option 21 only) Phase error versus Time measurement
DISPlay:PERRor:WINDow:TRACe:GRATicule:GRID:STATe Sets or queries the graticule grid view state for the Phase error
versus Time view.
DISPlay:PERRor:Y[:SCALe] Sets or queries the vertical scale.
DISPlay:PERRor:Y[:SCALe]:AUTO Sets the vertical scale automatically.
DISPlay:PERRor:Y[:SCALe]:OFFSet Sets or queries the minimum vertical value (bottom edge).
DISPlay:PHVTime subgroup Phase versus Time measurement
DISPlay:PHVTime[:MEASview<y>]:WINDow:TRACe:GRATicule:GR
ID:STATe
DISPlay:PHVTime[:MEASview<y>]:X[:SCALe] Sets or queries the horizontal scale.
DISPlay:PHVTime[:MEASview<y>]:X[:SCALe]:AUTO Sets the horizontal scale automatically.
DISPlay:PHVTime[:MEASview<y>]:X[:SCALe]:AUTO:STATe Determines whether to set the horizontal scale automatically or
DISPlay:PHVTime[:MEASview<y>]:X[:SCALe]:MAXimum? Queries the upper limit of the horizontal scale setting range.
DISPlay:PHVTime[:MEASview<y>]:X[:SCALe]:MINimum? Queries the lower limit of the horizontal scale setting range.
DISPlay:PHVTime[:MEASview<y>]:X[:SCALe]:OFFSet Sets or queries the minimum horizontal value (left edge).
DISPlay:PHVTime[:MEASview<y>]:X[:SCALe]:OFFSet:MAXimum? Queries the upper limit of the horizontal offset setting range.
DISPlay:PHVTime[:MEASview<y>]:X[:SCALe]:OFFSet:MINimum? Queries the lower limit of the horizontal offset setting range.
DISPlay:PHVTime[:MEASview<y>]:Y[:SCALe] Sets or queries the vertical scale.
DISPlay:PHVTime[:MEASview<y>]:Y[:SCALe]:AUTO Sets the vertical scale automatically.
DISPlay:PHVTime[:MEASview<y>]:Y[:SCALe]:AXIS Sets or queries the vertical axis representation.
DISPlay:PHVTime[:MEASview<y>]:Y[:SCALe]:AXIS:REFerence Sets or queries the reference time for phase.
DISPlay:PHVTime[:MEASview<y>]:Y[:SCALe]:OFFSet Sets or queries the vertical offset.
DISPlay:PHVTime[:MEASview<y>]:Y[:SCALe]:RESCale Rescales the vertical scale.
DISPlay:PNOise subgroup (Option 11 only) Phase noise measurements
DISPlay:PNOise:LEGend:STATe Sets or queries showing the trace legend on the display.
DISPlay:PNOise:MARKer:SHOW:STATe Determines whether to show the readout for the selected marker.
DISPlay:PNOise:RESet:SCALe Resets the horizontal and vertical scale to the default values.
DISPlay:PNOise:WINDow:TRACe:GRATicule:GRID:STATe Sets or queries whether to show the graticule grid on the screen.
DISPlay:PNOise:X[:SCALe]:AUTO Rescales the horizontal axis automatically.
DISPlay:PNOise:X[:SCALe]:STARt Sets or queries the start frequency of the graph.
DISPlay:PNOise:X[:SCALe]:STOP Sets or queries the stop frequency of the graph.
DISPlay:PNOise:Y[:SCALe] Sets or queries the stop frequency of the graph.
DISPlay:PNOise:Y[:SCALe]:AUTO Rescales the vertical axis automatically.
DISPlay:PNOise:Y[:SCALe]:OFFSet Sets or queries the vertical offset.
DISPlay:PNOise:Y[:SCALe]:PDIVision Sets or queries the vertical scale (per division).
DISPlay:PULSe subgroup Pulsed RF measurements
Table continued…
Sets or queries whether to show the graticule grid on the screen.
manually.
SignalVu-PC Vector Analysis Software Programmer Manual 59
Page 60
Syntax and Commands
Command Description
DISPlay:PULSe:MEASview<y>:DELete Deletes the measurement view.
DISPlay:PULSe:MEASview<y>[:SOURce<x>]:NEW Displays a new measurement view.
DISPlay:PULSe:MEASview<y>:SELect Selects the specifies Measurement view.
DISPlay:PULSe:RESult[:MEASview<y>]:ATX Sets or queries whether to show the average transmitted power
result.
DISPlay:PULSe:RESult[:MEASview<y>]:AVERage Sets or queries whether to show the average on power result.
DISPlay:PULSe:RESult[:MEASview<y>]:AVERage Sets or queries whether to show the average on power result.
DISPlay:PULSe:RESult[:MEASview<y>]:DRODb Sets or queries whether to show the droop in the results table.
DISPlay:PULSe:RESult[:MEASview<y>]:DROop Sets or queries showing the droop measurement result in the pulse
table
DISPlay:PULSe:RESult[:MEASview<y>]:DUTPct Sets or queries whether to show the duty factor (%) result.
DISPlay:PULSe:RESult[:MEASview<y>]:DUTRatio Sets or queries whether to show the duty factor (ratio) result.
DISPlay:PULSe:RESult[:MEASview<y>]:FALL Sets or queries whether to show the fall time in the results table.
DISPlay:PULSe:RESult[:MEASview<y>]:FDELta Sets or queries whether to show the delta frequency result.
DISPlay:PULSe:RESult[:MEASview<y>]:FRDeviation Sets or queries whether to show the frequency deviation result.
DISPlay:PULSe:RESult[:MEASview<y>]:IRAMplitude Sets or queries showing the Impulse Response Amplitude
measurement result in the pulse table.
DISPlay:PULSe:RESult[:MEASview<y>]:IRTime Sets or queries showing the Impulse Response Time measurement
result in the pulse table.
DISPlay:PULSe:RESult[:MEASview<y>]:MFReqerror Sets or queries whether to show the maximum frequency error
result.
DISPlay:PULSe:RESult[:MEASview<y>]:MPHerror Sets or queries whether to show the maximum phase error result.
DISPlay:PULSe:RESult[:MEASview<y>]:OVEDb Sets or queries whether to show the Overshoot measurement result
in dB in the pulse table.
DISPlay:PULSe:RESult[:MEASview<y>]:OVERshoot Sets or queries whether to show the Overshoot measurement result
in the pulse table.
DISPlay:PULSe:RESult[:MEASview<y>]:PHDeviation Sets or queries whether to show the phase deviation result.
DISPlay:PULSe:RESult[:MEASview<y>]:PPFRequency Sets or queries whether to show the pulse-pulse frequency result.
DISPlay:PULSe:RESult[:MEASview<y>]:PPOWer Sets or queries whether to show the peak power in the results table.
DISPlay:PULSe:RESult[:MEASview<y>]:PPPHase Sets or queries whether to show the pulse-pulse carrier phase
result.
DISPlay:PULSe:RESult[:MEASview<y>]:RINTerval Sets or queries whether to show the repetition interval result.
DISPlay:PULSe:RESult[:MEASview<y>]:RIPDb Sets or queries showing the ripple measurement result in dB in the
pulse table.
DISPlay:PULSe:RESult[:MEASview<y>]:RIPPle Sets or queries showing the ripple measurement result in dB in the
pulse table.
DISPlay:PULSe:RESult[:MEASview<y>]:RISE Sets or queries whether to show the rise time in the results table.
DISPlay:PULSe:RESult[:MEASview<y>]:RMSFreqerror Sets or queries whether to show the RMS frequency error result.
DISPlay:PULSe:RESult[:MEASview<y>]:RMSPherror Sets or queries whether to show the RMS phase error result.
DISPlay:PULSe:RESult[:MEASview<y>]:RRATe Sets or queries whether to show the repetition rate result.
Table continued…
60
Page 61
Syntax and Commands
Command Description
DISPlay:PULSe:RESult[:MEASview<y>]:TIME Sets or queries whether to show the time in the results table.
DISPlay:PULSe:RESult[:MEASview<y>]:WIDTh Sets or queries whether to show the pulse width in the results table.
DISPlay:PULSe:SELect[:MEASview<y>]:NUMBer Sets or queries the pulse to measure.
DISPlay:PULSe:SELect[:MEASview<y>]:RESult Sets or queries which result is shown in the trace and statistics
views.
DISPlay:PULSe:STATistics[:MEASview<y>]:MARKer<x>:SHOW:ST
ATe
DISPlay:PULSe:STATistics[:MEASview<y>]:PLOT Sets or queries how to show the statistics graph.
DISPlay:PULSe:STATistics[:MEASview<y>]:WINDow:TRACe:GRAT
icule:GRID:STATe
DISPlay:PULSe:STATistics[:MEASview<y>]:X:RSCale Rescales the horizontal axis of the statistics graph.
DISPlay:PULSe:STATistics[:MEASview<y>]:X[:SCALe]:NUMBer Sets or queries the horizontal scale (the number of pulses per
DISPlay:PULSe:STATistics[:MEASview<y>]:X[:SCALe]:OFFSet Sets or queries the minimum horizontal value in the statistics view.
DISPlay:PULSe:STATistics[:MEASview<y>]:Y:RSCale Rescales the vertical axis of the statistics graph.
DISPlay:PULSe:STATistics[:MEASview<y>]:Y[:SCALe]:FULL Sets or queries the vertical full-scale in the statistics view.
DISPlay:PULSe:STATistics[:MEASview<y>]:Y[:SCALe]:OFFSet Sets or queries the vertical offset in the statistics view.
DISPlay:PULSe:STATistics[:MEASview<y>]:Y[:SCALe]:STOP? Queries the minimum vertical value in the statistics view.
DISPlay:PULSe:TRACe[:MEASview<y>]:MARKer<x>:SHOW:STATe Sets or queries whether to show the marker readout in the trace
DISPlay:PULSe:TRACe[:MEASview<y>]:POINt:SHOW Sets or queries whether to show the measurement points and lines.
DISPlay:PULSe:TRACe[:MEASview<y>]:WINDow:TRACe:GRATicu
le:GRID:STATe
DISPlay:PULSe:TRACe[:MEASview<y>]:X:RSCale Rescales the horizontal axis of the pulse trace view.
DISPlay:PULSe:TRACe[:MEASview<y>]:X[:SCALe] Sets or queries the horizontal full scale in the pulse trace view.
DISPlay:PULSe:TRACe[:MEASview<y>]:X[:SCALe]:FULL Sets or queries the full-scale reference for the horizontal rescale.
DISPlay:PULSe:TRACe[:MEASview<y>]:X[:SCALe]:OFFSet Sets or queries the minimum horizontal value in the pulse trace
DISPlay:PULSe:TRACe[:MEASview<y>]:X[:SCALe]:PDIVision Sets or queries the horizontal full scale in the pulse trace view.
DISPlay:PULSe:TRACe[:MEASview<y>]:Y:RSCale Rescales the vertical axis of the pulse trace view.
DISPlay:PULSe:TRACe[:MEASview<y>]:Y[:SCALe]:FULL Sets or queries the vertical full scale in the pulse trace view.
DISPlay:PULSe:TRACe[:MEASview<y>]:Y[:SCALe]:OFFSet Sets or queries the vertical offset in the pulse trace view.
DISPlay:PULSe:TRACe[:MEASview<y>]:Y[:SCALe]:STOP? Queries the minimum vertical value in the pulse trace view.
DISPlay:SEM subgroup Spectral Emissions Mask measurements
DISPlay:SEM:MARKer:SHOW:STATe Determines whether to show or hide the readout for the selected
DISPlay:SEM:RESet:SCALe Resets the scale.
DISPlay:SEM:SHOW:LIMit Sets or queries the appearance of the limits.
DISPlay:SEM:WINDow:TRACe:GRATicule:GRID:STATe Determines whether to show or hide the graticule.
Table continued…
Sets or queries whether to show the marker readout in the graph.
Sets or queries whether to show the graticule grid in the statistics
view.
division).
view.
Sets or queries whether to show the graticule grid in the trace view.
view.
marker.
SignalVu-PC Vector Analysis Software Programmer Manual 61
Page 62
Syntax and Commands
Command Description
DISPlay:SEM:X[:SCALe]:AUTO Rescales the horizontal scale automatically to fit the waveform.
DISPlay:SEM:X[:SCALe]:START Sets or queries the start frequency.
DISPlay:SEM:X[:SCALe]:STOP Sets or queries the stop frequency.
DISPlay:SEM:Y[:SCALe] Sets or queries the vertical range.
DISPlay:SEM:Y[:SCALe]:AUTO Rescales the vertical scale automatically to fit the waveform.
DISPlay:SEM:Y[:SCALe]:OFFSet Sets or queries the vertical offset.
DISPlay:SGRam subgroup Spectrogram measurement
DISPlay:SGRam[:MEASview<y>]:FREQuency:AUTO Rescales the horizontal (frequency) axis automatically.
DISPlay:SGRam[:MEASview<y>]:FREQuency:OFFSet Sets or queries the horizontal (frequency) offset.
DISPlay:SGRam[:MEASview<y>]:FREQuency:SCAle Sets or queries the horizontal (frequency) range.
DISPlay:SGRAM[:MEASview<y>]:MARKer:SHOW:STATe Sets or queries the marker readout.
DISPlay:SGRAM[:MEASview<y>]:SELected:TIMestamp Sets or queries the time stamp readout.
DISPlay:SGRam[:MEASview<y>]:TIME:AUTO Rescales the vertical axis automatically.
DISPlay:SGRam[:MEASview<y>]:TIME:OFFSet Sets or queries the vertical axis (time) offset (bottom line number).
DISPlay:SGRam[:MEASview<y>]:TIME:OFFSet:DIVisions Sets or queries the Vertical offset or Position in divisions.
DISPlay:SGRam[:MEASview<y>]:TIME:OVERlap:PERCent Sets or queries the Overlap in percent.
DISPlay:SGRam[:MEASview<y>]:TIME:SCAle Sets or queries the vertical scale (the amount of time in each line).
DISPlay:SGRam[:MEASview<y>]:TIME:SCALe:PER:DIVision Sets or queries the vertical Time/division value.
DISPlay:SGRam[:MEASview<y>]:TIME:SPECtrums:PERLine? Queries the Spectrums/Line value.
DISPlay:SPECtrum subgroup Spurious measurement
DISPlay:SPURious:MARKer:SHOW:STATe Sets or queries whether to show the readout for the selected
marker.
DISPlay:SPURious:RESet:SCALe Resets the horizontal and vertical scale to the default values.
DISPlay:SPURious:SCALe:LOG:STATe Sets or queries whether to set the horizontal axis logarithmic.
DISPlay:SPURious:SELect:NUMBer Sets or queries the spurious number.
DISPlay:SPURious:SHOW:LIMit Sets or queries how to display the limits.
DISPlay:SPURious:WINDow:TRACe:GRATicule:GRID:STATe Determines whether to show the graticule grid on screen.
DISPlay:SPURious:X[:SCALe]:AUTO Rescales the horizontal axis automatically.
DISPlay:SPURious:X[:SCALe]:STARt Sets or queries the minimum horizontal value of the spectrum
graph.
DISPlay:SPURious:X[:SCALe]:STOP Sets or queries the maximum horizontal value of the spectrum
graph.
DISPlay:SPURious:Y[:SCALe] Sets or queries the vertical range of the spectrum graph.
DISPlay:SPURious:Y[:SCALe]:AUTO Rescales the vertical axis automatically.
DISPlay:SPURious:Y[:SCALe]:OFFSet Sets or queries the vertical offset of the spectrum graph.
DISPlay:TDIagram subgroup (Option 21 only) Trellis diagram
DISPlay:TDIagram:WINDow:TRACe:GRATicule:GRID:STATe Sets or queries whether to show the graticule grid on the screen.
DISPlay:TDIagram:Y[:SCALe] Sets or queries the vertical scale.
Table continued…
62
Page 63
Syntax and Commands
Command Description
DISPlay:TDIagram:Y[:SCALe]:AUTO Sets the vertical scale automatically.
DISPlay:TDIagram:Y[:SCALe]:OFFSet Sets or queries the vertical offset (center point of the vertical axis).
DISPlay:TOVerview subgroup Time overview
DISPlay:TOVerview[:MEASview<y>]:WINDow:TRACe:GRATicule:G
RID:STATe
DISPlay:TOVerview[:MEASview<y>]:X[:SCALe] Sets or queries the horizontal scale.
DISPlay:TOVerview[:MEASview<y>]:X[:SCALe]:AUTO Sets the horizontal scale and offset automatically.
DISPlay:TOVerview[:MEASview<y>]:X[:SCALe]:OFFSet Sets or queries the minimum horizontal value (left edge).
DISPlay:TOVerview[:MEASview<y>]:Y[:SCALe] Sets or queries the vertical scale.
DISPlay:TOVerview[:MEASview<y>]:Y[:SCALe]:AUTO Sets the vertical scale and offset automatically.
DISPlay:TOVerview[:MEASview<y>]:Y[:SCALe]:OFFSet Sets or queries the vertical offset.
DISPlay:TOVerview[:MEASview<y>]:Y[:SCALe]:RESCale Rescales the vertical scale.
DISPlay:WINDow subgroup Window display
DISPlay:WINDow:ACTive:MEASurement? Queries the active measurement views
DISPlay:WINDow:COLor:SCHeme Sets or queries the color scheme for displaying traces and
DISPlay:WINDow:OPTimized:MEASurement? Queries the measurement views that are optimized.
DISPlay:WLAN subgroup Wireless LAN measurements
DISPlay:WLAN:CONSte[:SCALe] Sets the magnification value (zoom factor).
DISPlay:WLAN:CONSte:X:OFFSet Sets or queries the value of the offset of the horizontal axis.
DISPlay:WLAN:CONSte:Y:OFFSet Sets or queries the value of the offset of the vertical axis.
DISPlay:WLAN:CRESponse:AUTO Automatically rescales the horizontal and vertical values.
DISPlay:WLAN:CRESponse:FREQuency:AUTO Automatically rescales the horizontal subcarrier (frequency) start
DISPlay:WLAN:CRESponse:FREQuency:STARt Specifies or queries the horizontal start value.
DISPlay:WLAN:CRESponse:FREQuency:STOP Specifies or queries the horizontal stop value.
DISPlay:WLAN:CRESponse:MAGNitude:AUTO Rescales the vertical magnitude offset (position) and scale values.
DISPlay:WLAN:CRESponse:MAGNitude:OFFSet Sets or queries the vertical offset.
DISPlay:WLAN:CRESponse:MAGNitude[:SCALe] Sets or queries the value of the vertical scale.
DISPlay:WLAN:CRESponse:MARKer:SHOW:STATe Shows or hides the marker readout.
DISPlay:WLAN:CRESponse:PHASe:AUTO Rescales the vertical phase value automatically to fit the waveform
DISPlay:WLAN:CRESponse:PHASe:OFFSet Sets or queries the vertical offset.
DISPlay:WLAN:CRESponse:PHASe[:SCALe] Sets or queries the phase value.
DISPlay:WLAN:CRESponse:WINDow:SELect:PLOT Specifies or queries which graphs are displayed.
DISPlay:WLAN:CRESponse:WINDow:TRACe:GRATicule:GRID:ST
ATe
DISPlay:WLAN:EVM:FREQuency:AUTO Automatically rescales the horizontal subcarrier (frequency) start
Table continued…
Sets or queries whether to show the graticule grid in the time
overview.
background on the screen.
and stop values.
to the screen.
Sets or queries whether to show the graticule grid.
and stop values.
SignalVu-PC Vector Analysis Software Programmer Manual 63
Page 64
Syntax and Commands
Command Description
DISPlay:WLAN:EVM:FREQuency:RESet Automatically resets the horizontal subcarrier (frequency) start and
stop values.
DISPlay:WLAN:EVM:FREQuency:STARt Specifies or queries the horizontal start value.
DISPlay:WLAN:EVM:FREQuency:STOP Specifies or queries the horizontal stop value.
DISPlay:WLAN:EVM:MARKer:SHOW:STATe Shows or hides the Marker readout.
DISPlay:WLAN:EVM[:SCALe]:AUTO Automatically adjusts all vertical and horizontal values.
DISPlay:WLAN:EVM:TIME:AUTO Sets the horizontal start and stop values to fit the waveform.
DISPlay:WLAN:EVM:TIME:AUTO:STATe Automatically sets the horizontal symbol scale value.
DISPlay:WLAN:EVM:TIME:RESet Resets the horizontal symbol start and stop values.
DISPlay:WLAN:EVM:TIME:STARt Sets or queries the horizontal symbol start value.
DISPlay:WLAN:EVM:TIME:STOP Sets or queries the horizontal symbol stop value
DISPlay:WLAN:EVM:WINDow:SELect:PLOT Specifies or queries which graphs are displayed in the WLAN EVM
display.
DISPlay:WLAN:EVM:WINDow:TRACe:GRATicule:GRID:STATe Shows or hides the graticule grid on the screen.
DISPlay:WLAN:EVM:Y:AUTO Automatically sets the vertical scale and position values.
DISPlay:WLAN:EVM:Y:OFFSet Sets or queries the value of the offset from the center.
DISPlay:WLAN:EVM:Y:RESet Resets the vertical scale and position (offset) values.
DISPlay:WLAN:EVM:Y[:SCALe] Sets or queries the vertical scale value.
DISPlay:WLAN:FLATness:AUTO Automatically rescales the horizontal and vertical axes.
DISPlay:WLAN:FLATness:X:AUTO Automatically rescales the horizontal axis.
DISPlay:WLAN:FLATness:X:OFFSet Sets or queries the value of the offset of the horizontal axis from the
center.
DISPlay:WLAN:FLATness:X[:SCALe] Sets or queries the horizontal scale value.
DISPlay:WLAN:FLATness:Y:AUTO Automatically rescales the vertical axis scale and position values.
DISPlay:WLAN:FLATness:Y:OFFSet Sets or queries the value of the offset from the center.
DISPlay:WLAN:FLATness:Y[:SCALe] Sets or queries the vertical scale value.
DISPlay:WLAN:MEASview:DELete Deletes the selected measurement view.
DISPlay:WLAN:MEASview:NEW Displays a new measurement view.
DISPlay:WLAN:MEASview:SELect Selects a WLAN measurement view.
DISPlay:WLAN:MERRor:FREQuency:AUTO Automatically rescales the horizontal subcarrier (frequency) start
and stop values.
DISPlay:WLAN:MERRor:FREQuency:RESet Automatically resets the horizontal subcarrier (frequency) start and
stop values.
DISPlay:WLAN:MERRor:FREQuency:STARt Specifies or queries the horizontal start value.
DISPlay:WLAN:MERRor:FREQuency:STOP Specifies or queries the horizontal stop value.
DISPlay:WLAN:MERRor:MARKer:SHOW:STATe Shows or hides the marker readout.
DISPlay:WLAN:MERRor[:SCALe]:AUTO Automatically adjusts all vertical and horizontal values.
DISPlay:WLAN:MERRor:TIME:AUTO Sets the horizontal start and stop values.
Table continued…
64
Page 65
Syntax and Commands
Command Description
DISPlay:WLAN:MERRor:TIME:AUTO:STATe Automatically sets the horizontal symbol scale value.
DISPlay:WLAN:MERRor:TIME:RESet Resets the horizontal symbol start and stop values.
DISPlay:WLAN:MERRor:TIME:STARt Sets or queries the horizontal symbol start value.
DISPlay:WLAN:MERRor:TIME:STOP Sets or queries the horizontal symbol stop value.
DISPlay:WLAN:MERRor:WINDow:SELect:PLOT Specifies or queries which graphs are displayed.
DISPlay:WLAN:MERRor:WINDow:TRACe:GRATicule:GRID:STATe Shows or hides the graticule grid on the display.
DISPlay:WLAN:MERRor:Y:AUTO Automatically sets the vertical scale and position values.
DISPlay:WLAN:MERRor:Y:OFFSet Sets or queries the offset from the center (vertical position).
DISPlay:WLAN:MERRor:Y:RESet Resets the vertical scale and position (offset).
DISPlay:WLAN:MERRor:Y[:SCALe] Sets or queries the vertical scale value.
DISPlay:WLAN:PERRor:FREQuency:AUTO Automatically rescales the horizontal subcarrier (frequency) start
and stop values.
DISPlay:WLAN:PERRor:FREQuency:RESet Automatically resets the horizontal subcarrier (frequency) start and
stop values.
DISPlay:WLAN:PERRor:FREQuency:STARt Specifies or queries the horizontal start value.
DISPlay:WLAN:PERRor:FREQuency:STOP Specifies or queries the horizontal stop value.
DISPlay:WLAN:PERRor:MARKer:SHOW:STATe Show or hides the Marker readout.
DISPlay:WLAN:PERRor[:SCALe]:AUTO Automatically adjusts all vertical and horizontal settings.
DISPlay:WLAN:PERRor:TIME:AUTO Automatically sets the horizontal symbol start and stop values.
DISPlay:WLAN:PERRor:TIME:AUTO:STATe Automatically sets the horizontal symbol scale value.
DISPlay:WLAN:PERRor:TIME:RESet Resets the horizontal symbol start and stop values.
DISPlay:WLAN:PERRor:TIME:STARt Sets or queries the horizontal symbol start value.
DISPlay:WLAN:PERRor:TIME:STOP Sets or queries the horizontal symbol stop value.
DISPlay:WLAN:PERRor:WINDow:SELect:PLOT Specifies or queries which displays are displayed.
DISPlay:WLAN:PERRor:WINDow:TRACe:GRATicule:GRID:STATe Shows or hides the graticule grid on the screen.
DISPlay:WLAN:PERRor:Y:AUTO Automatically selects the vertical scale and position values.
DISPlay:WLAN:PERRor:Y:OFFSet Sets or queries the value of the offset from the center (vertical
position).
DISPlay:WLAN:PERRor:Y:RESet Resets the vertical scale and position (offset) values.
DISPlay:WLAN:PERRor:Y[:SCALe] Sets or queries the vertical scale value.
DISPlay:WLAN:PVTime:BURSt:X[:SCALe] Sets or queries the value of the scale (width).
DISPlay:WLAN:PVTime:BURSt:X[:SCALe]:AUTO Automatically sets the starting time (position) and scale (width)
values
DISPlay:WLAN:PVTime:BURSt:X[:SCALe]:OFFSet Sets or queries the starting time (position) value.
DISPlay:WLAN:PVTime:BURSt:X[:SCALe]:RESet Resets the starting time (position) and scale (width) values.
DISPlay:WLAN:PVTime:FALL:X[:SCALe] Sets or queries the scale (width) value.
DISPlay:WLAN:PVTime:FALL:X[:SCALe]:AUTO Automatically sets the starting time (position) and scale (width)
values.
Table continued…
SignalVu-PC Vector Analysis Software Programmer Manual 65
Page 66
Syntax and Commands
Command Description
DISPlay:WLAN:PVTime:FALL:X[:SCALe]:OFFSet Sets or queries the value for the starting time (offset).
DISPlay:WLAN:PVTime:FALL:X[:SCALe]:RESet Resets the starting time (position) and scale (width) values.
DISPlay:WLAN:PVTime:MARKer:SHOW:STATe Shows or hides the marker readout.
DISPlay:WLAN:PVTime:RISE:X[:SCALe] Sets or queries the scale (width) value.
DISPlay:WLAN:PVTime:RISE:X[:SCALe]:AUTO Automatically sets the starting time (position) and scale (width)
values.
DISPlay:WLAN:PVTime:RISE:X[:SCALe]:OFFSet Sets or queries the starting time value (offset).
DISPlay:WLAN:PVTime:RISE:X[:SCALe]:RESet Resets the starting time (position) and scale (width) values.
DISPlay:WLAN:PVTime:WINDow:SELect:PLOT Specifies or queries which view to use.
DISPlay:WLAN:PVTime:WINDow:TRACe:GRATicule:GRID:STATe Shows or hides the graticule grid on the screen.
DISPlay:WLAN:PVTime:Y[:SCALe] Sets or queries the vertical scale value.
DISPlay:WLAN:PVTime:Y[:SCALe]:AUTO Automatically selects the vertical scale and position values.
DISPlay:WLAN:PVTime:Y[:SCALe]:OFFSet Sets or queries the value of the vertical offset.
DISPlay:WLAN:PVTime:Y[:SCALe]:PDIVision Sets or queries the value of the vertical scale.
DISPlay:WLAN:PVTime:Y[:SCALe]:RESet Resets the vertical scale and position (offset) values.
DISPlay:WLAN:SUMMary:EVMUnits Sets or queries the EVM Units setting.
DISPlay:LTE subgroup
DISPlay:LTE:ACLR:MARKer:SHOW:STATe Determines whether to show or hide the readout for the selected
marker.
DISPlay:LTE:ACLR:RESet:SCALe Resets the horizontal and vertical scale to default values.
DISPlay:LTE:ACLR:SHOW:LIMit Sets or queries the appearance of the limits.
DISPlay:LTE:ACLR:WINDow:TRACe:GRATicule:GRID:STATe Determines whether to show or hide the graticules.
DISPlay:LTE:ACLR:WINDow:TRACe:POWer:LEVEl:STATe Determines whether to show or hide the power readout.
DISPlay:LTE:ACLR:X:SCALe Sets or queries the horizontal range.
DISPLay:LTE:ACLR:X:SCALe:AUTO Rescales the horizontal axis automatically to fit the waveform to the
screen.
DISPlay:LTE:ACLR:X:SCALe:OFFSet Sets or queries the center frequency of the trace.
DISPlay:LTE:ACLR:Y:SCALe:AUTO Rescales the vertical scale automatically to fit the waveform on the
screen.
DISPlay:LTE:ACLR:Y:SCALe:OFFSet Sets or queries the vertical offset of the trace.
DISPlay:LTE:ACLR:Y:SCALe Sets or queries the vertical range of the graph.
DISPlay:LTE:CHSPectrum:MARKer:SHOW:STATe Determines whether to show or hide the readout for the selected
marker.
DISPlay:LTE:CHSPectrum:RESet:SCALe Resets the horizontal and vertical scale to default values.
DISPlay:LTE:CHSPectrum:WINDow:TRACe:GRATicule:GRID:STATeDetermines whether to show or hide the graticule.
DISPlay:LTE:CHSPectrum:X:SCALe Sets or queries the horizontal range.
DISPLay:LTE:CHSpectrum:X:SCALe:AUTO Rescales the horizontal axis automatically to fit the waveform to the
screen.
Table continued…
66
Page 67
Syntax and Commands
Command Description
DISPlay:LTE:CHSPectrum:X:SCALe:OFFSet Sets or queries the center frequency of the trace.
DISPlay:LTE:CHSPectrum:Y:SCALe Sets or queries the vertical range of the graph.
DISPlay:LTE:CHSPectrum:Y:SCALe:AUTO Rescales the vertical scale automatically to fit the waveform on the
screen.
DISPlay:LTE:CHSPectrum:Y:SCALe:OFFSet Sets or queries the vertical offset of the trace.
DISPlay:LTE:CONSte:SCALe Sets or queries the scale (zoom).
DISPlay:LTE:CONSte:X:OFFSet Sets or queries the horizontal offset.
DISPlay:LTE:CONSte:Y:OFFSet Sets or queries the vertical offset.
DISPlay:LTE:MEASview<y>:DELete Deletes the selected LTE measurement display in the application.
DISPlay:LTE:MEASview<y>:NEW Opens a new LTE measurement display.
DISPlay:LTE:MEASview<y>:SELect Selects an LTE measurement display in the application. The query
returns the currently selected display.
DISPlay:LTE:PVTime:MARKer:SHOW:STATe Shows or hides the marker readout.
DISPlay:LTE:PVTime:WINDow:TRACe:GRATicule:GRID:STATe Determines whether to show or hide the graticule.
DISPlay:LTE:PVTime:X:SCALe Sets or queries the vertical range.
DISPLay:LTE:PVTime:X:SCALe:AUTO Rescales the horizontal axis automatically to fit the waveform to the
screen.
DISPlay:LTE:PVTime:X:SCALe:RESet Resets the horizontal scale to the default value for the time
measurements.
DISPlay:LTE:PVTime:Y:SCALe Sets or queries the horizontal range.
DISPlay:LTE:PVTime:Y:SCALe:AUTO Rescales the vertical scale automatically to fit the waveform on the
screen.
DISPlay:LTE:PVTime:Y:SCALe:OFFSet Sets or queries the vertical offset (top edge of the vertical axis) of
the trace.
DISPlay:LTE:PVTime:Y:SCALe:PDIVision Sets or queries the value of the vertical scale in dB/division.
DISPlay:LTE:PVTime:Y:SCALe:RESet Resets the vertical scale and position (offset) to the default value for
the time measurements.
Fetch commands
The FETCh commands retrieve the measurements from the data taken by the latest INITiate command. See the Index for commands not
listed in the following table.
To perform a FETCh operation on fresh data, use the READ commands, which acquire a new input signal and fetch the measurement
results from that data.
Not all of these commands apply to SignalVu-PC and connected instruments. See the individual command descriptions for details.
Table 16: Fetch commands
Command Description
FETCh TXGain command subgroup Transmission Gain measurements
FETCh:TXGain:AVERage? Returns the mean value of the trace.
Table continued…
SignalVu-PC Vector Analysis Software Programmer Manual 67
Page 68
Syntax and Commands
Command Description
FETCh:TXGain:MAX? Returns the maximum trace value.
FETCh:TXGain:MAXLocation? Returns the frequency of the maximum trace value.
FETCh:TXGain:MIN? Returns the minimum trace value.
FETCh:TXGain:MINLocation? Returns the frequency of the minimum trace value.
FETCh:TXGain:TRACe<x>? Returns the trace data of the selected trace.
FETCh basic command subgroup General fetch control
FETCh:RFIN:IQ? Returns time-domain IQ data for a specific acquisition data record.
FETCh: BLuetooth subgroup Bluetooth measurements
FETCh:BIBEmissions:FTX? Returns the band number corresponding to the transmitted FTX
detected in the display.
FETCh:BIBEmissions:POWer? Returns all channel power results.
FETCh:BIBEmissions:RESUlts:STATus? Returns the Pass/Fail result status.
FETCh:BLUEtooth:CONSte:FERRor? Returns the frequency error.
FETCh:BLUEtooth:CONSte:TRACe? Queries the trace data.
FETCh:BLUEtooth:EDIagram:FDEViation? Returns the frequency deviation vs. time trace data with the X
values.
FETCh:BLUEtooth:EDIagram:FERRor? Returns the frequency error.
FETCh:BLUEtooth:EDIagram:HORiz:SCALe? Returns the value of the horizontal scale.
FETCh:BLUEtooth:EDIagram:I? Returns the I vs. time trace.
FETCh:BLUEtooth:EDIagram:Q? Returns the Q vs. time trace.
FETCh:BLUEtooth:FDVTime:TRACe? Returns the trace data.
FETCh:BLUEtooth:FREQuency:ERROr? Returns the frequency error from the Bluetooth Constellation
diagram.
FETCh:BLUEtooth:FREQuency:ERROr:TYPE? Returns the frequency error type in the Bluetooth Constellation
display.
FETCh:BLUEtooth:FREQuency:OFFSet:DRIFt:F1FZero? Returns the drift in frequency offset (f1–f0—the frequency offset
calculated in the first interval in the payload — the frequency offset
calculated in the preamble) in the Bluetooth Frequency Deviation
vs. Time display.
FETCh:BLUEtooth:FREQuency:OFFSet:DRIFt:FNFN5? Returns the maximum drift of the frequency offset in payload
intervals spaced 50 μs away in the Bluetooth Frequency Deviation
vs. Time display.
FETCh:BLUEtooth:FREQuency:OFFSet:DRIFt:FNFN5:INTErval? Returns the interval at which the maximum drift of frequency offset
in a duration of 50 μs occurred.
FETCh:BLUEtooth:FREQuency:OFFSet:DRIFt:FNFZERO?
Returns the maximum drift of the frequency offset of the intervals in
the payload from the preamble packet in the Bluetooth Frequency
Deviation vs. Time display.
FETCh:BLUEtooth:FREQuency:OFFSet:DRIFt:FNFZERO:INTErval
?
Table continued…
68
Returns the interval (n) at which the maximum drift fn-f0 occurred in
the Bluetooth Frequency Deviation vs. Time display.
Page 69
Syntax and Commands
Command Description
FETCh:BLUEtooth:FREQuency:OFFSet:MAX? Returns the maximum frequency offset in the Frequency Deviation
vs. Time and the Center Frequency Offset and Drift displays.
FETCh:BLUEtooth:FREQuency:OFFSet:MAX:INTErval? Returns the maximum frequency offset interval in the Frequency
Deviation vs. Time and the Center Frequency Offset and Drift
displays.
FETCh:BLUEtooth:FREQuency:OFFSet:PREAmble? Returns the offset calculated in the preamble region in the
Frequency Deviation vs. Time and the Center Frequency Offset
and Drift displays.
FETCh:BLUEtooth:MODUlation:CHARacteristics:AVErage:F? Returns the average frequency value when the selected test pattern
is Other in the Bluetooth Frequency Deviation vs. Time display.
FETCh:BLUEtooth:MODUlation:CHARacteristics:AVErage:F2F1ratio?Returns the average ratio value for the high and low frequency
deviation in the Bluetooth Frequency Deviation vs. Time display.
FETCh:BLUEtooth:MODUlation:CHARacteristics:AVErage:FONE? Returns the average frequency deviation for the low deviation
pattern in the Bluetooth Frequency Deviation vs. Time display.
FETCh:BLUEtooth:MODUlation:CHARacteristics:AVErage:FTWO? Returns the average frequency deviation for the high deviation
pattern in the Bluetooth Frequency Deviation vs. Time display.
FETCh:BLUEtooth:SUMMary:FREQuency:OFFSet:DRIFt:COUNt? Returns the number of packets analyzed to obtain average drift
results.
FETCh:BLUEtooth:SUMMary:FREQuency:OFFSet:DRIFt:F1FZero? Returns the drift f1–f0.
FETCh:BLUEtooth:SUMMary:FREQuency:OFFSet:DRIFt:F1FZero:
STATus?
FETCh:BLUEtooth:SUMMary:FREQuency:OFFSet:DRIFt:FNFN5? Returns the maximum drift of the fn–fn-5 value.
FETCh:BLUEtooth:SUMMary:FREQuency:OFFSet:DRIFt:FNFN5:S
TATus?
FETCh:BLUEtooth:SUMMary:FREQuency:OFFSet:DRIFt:FNFZero?Returns the maximum drift fn–f0.
Returns the Pass/Fail drift f1–f0 result status in the packet.
Returns the Pass/Fail status of the maximum fn–fn-5 drift in the
packet.
FETCh:BLUEtooth:SUMMary:FREQuency:OFFSet:DRIFt:FNFZero:
STATus?
FETCh:BLUEtooth:SUMMary:FREQuency:OFFSet:MAX? Returns the maximum frequency offset present in the packet.
FETCh:BLUEtooth:SUMMary:FREQuency:OFFSet:MAX:STATus? Returns the Pass/Fail result status of the frequency offset maximum
FETCh:BLUEtooth:SUMMary:FREQuency:OFFSet:PREAmble? Returns the frequency offset value in the preamble region.
FETCh:BLUEtooth:SUMMary:FREQuency:OFFSet:PREAmble:STA
Tus?
FETCh:BLUEtooth:SUMMary:MODUlation:CHARacteristics:AVErag
e: DELTa:F:MAX:PERCentage:COUNt?
FETCh:BLUEtooth:SUMMary:MODUlation:CHARacteristics:AVErag
e:DELTa:FONE:MAX:PERCentage:COUNt?
FETCh:BLUEtooth:SUMMary:MODUlation:CHARacteristics:AVErag
e:DELTa:FTWO:MAX:PERCentage?
FETCh:BLUEtooth:SUMMary:MODUlation:CHARacteristics:AVErag
e:DELTa:FTWO:MAX:PERCentage:COUNt?
Table continued…
Returns the Pass/Fail result status of the fn–f0 maximum drift in the
packet.
in the packet.
Returns the Pass/Fail result status of the frequency offset in the
preamble region.
Returns the number of packets analyzed out of 10 packets for ΔF
average.
Returns the number of packets analyzed out of 10 packets for the
ΔF1avg.
Returns the percentage of the ΔF2Max values that are above the
specified limit.
Returns the number of packets analyzed out of 10 packets for the
ΔF2Max%.
SignalVu-PC Vector Analysis Software Programmer Manual 69
Page 70
Syntax and Commands
Command Description
FETCh:BLUEtooth:SUMMary:MODUlation:CHARacteristics:AVErag
e:DELTa:FTWO:MAX:PERCentage:STATus?
FETCh:BLUEtooth:SUMMary:MODUlation:CHARacteristics:AVErag
e:F?
FETCh:BLUEtooth:SUMMary:MODUlation:CHARacteristics:AVErag
e:F2F1ratio?
FETCh:BLUEtooth:SUMMary:MODUlation:CHARacteristics:AVErag
e:F2F1ratio:STATus?
FETCh:BLUEtooth:SUMMary:MODUlation:CHARacteristics:AVErag
e:FONE?
FETCh:BLUEtooth:SUMMary:MODUlation:CHARacteristics:AVErag
e:FONE:STATus?
FETCh:BLUEtooth:SUMMary:MODUlation:CHARacteristics:AVErag
e:FTWO?
FETCh:BLUEtooth:SUMMary:OUTPut:POWEr:AVErage? Returns the average output power.
FETCh:BLUEtooth:SUMMary:OUTPut:POWEr:AVErage:STATus? Returns the Pass/Fail results status of the average output power.
FETCh:BLUEtooth:SUMMary:OUTPut:POWEr:COUNt? Returns the number of packets analyzed out of 10 packets for
FETCh:BLUEtooth:SUMMary:OUTPut:POWEr:EDR:COUNt? Returns the number of packets analyzed out of 10 packets for
FETCh:BLUEtooth:SUMMary:OUTPut:POWEr:EDR:DPSK? Returns the power in the DPSK portion of the EDR burst.
FETCh:BLUEtooth:SUMMary:OUTPut:POWEr:EDR:GPSK? Returns the power in the GFSK portion of the EDR burst.
FETCh:BLUEtooth:SUMMary:OUTPut:POWEr:PEAK? Returns the peak output power.
FETCh:BLUEtooth:SUMMary:OUTPut:POWEr:PEAK:STATus? Returns the Pass/Fail results status of the peak output power.
FETCh:BLUEtooth:SUMMary:PACKet:BDR:CRC? Returns the Basic Rate value of the CRC field.
FETCh:BLUEtooth:SUMMary:PACKet:BDR:HEADer:ARQN? Returns the value of ARQN field.
FETCh:BLUEtooth:SUMMary:PACKet:BDR:HEADer:FLOW? Returns the value of Flow field.
FETCh:BLUEtooth:SUMMary:PACKet:BDR:HEADer:HEC? Returns the value of HEC field.
FETCh:BLUEtooth:SUMMary:PACKet:BDR:HEADer:LT:ADDRess? Returns the LT address.
FETCh:BLUEtooth:SUMMary:PACKet:BDR:HEADer:SEQN? Returns the value of SEQN field.
FETCh:BLUEtooth:SUMMary:PACKet:BDR:HEADer:TYPE? Returns the value of Type field.
FETCh:BLUEtooth:SUMMary:PACKet:BDR:PAYLoad:LENgth? Returns the Basic Rate payload length.
FETCh:BLUEtooth:SUMMary:PACKet:BDR:PREAmble? Returns the preamble of the Basic Rate packet.
FETCh:BLUEtooth:SUMMary:PACKet:BDR:SYNC:WORD? Returns the sync word.
FETCh:BLUEtooth:SUMMary:PACKet:BDR:TYPE? Returns the packet type of the Basic Rate signal.
FETCh:BLUEtooth:SUMMary:PACKet:BLE:ACCEss:ADDRess? Returns the 32-bit Access Address.
FETCh:BLUEtooth:SUMMary:PACKet:BLE:CRC? Returns the value of the CRC field.
FETCh:BLUEtooth:SUMMary:PACKet:BLE:PDU:HEADer:LENGth? Returns the value of the length field.
FETCh:BLUEtooth:SUMMary:PACKet:BLE:PDU:HEADer:RX:ADDR
ess?
Table continued…
Returns the Pass/Fail result status of the ΔF2Max% field.
Returns the ΔFavg value.
Returns the ratio of the ΔF2avg to ΔF1avg.
Returns the Pass/Fail results status of the ΔF2avg/ΔF1avg field.
Returns the ΔF1avg value.
Returns the Pass/Fail results status of the ΔF1avg.
Returns the ΔF2avg value.
thecalculation of the output power.
calculation of the output power for EDR.
Returns the Rx address.
70
Page 71
Syntax and Commands
Command Description
FETCh:BLUEtooth:SUMMary:PACKet:BLE:PDU:HEADer:TX:ADDR
ess?
FETCh:BLUEtooth:SUMMary:PACKet:BLE:PDU:HEADer:TYPE? Returns the PDU type.
FETCh:BLUEtooth:SUMMary:PACKet:BLE:PREAmble? Returns the preamble of the BLE packet.
FETCh:BLUEtooth:SUMMary:PACKet:BLE:TYPE? Returns the packet type.
FETCH:NOISe subgroup Noise Figure and Gain measurements
FETCh:NOISe:GAIN:TRACe<x>:RESult? This query returns the gain value in mdB of the specified trace in
FETCh:NOISe:TABLe:VALue? Returns Noise Table data. A total of 7 values per frequency (28
FETCH:OBWidth subgroup Bluetooth 20dB BW measurements
FETCh:OBWidth:BOBW:XDBBandwidth? Returns the difference between the higher and lower frequency
FETCh:OBWidth:BOBW:XDBMbandwidth:IN:BANDwidth? Returns the difference between the higher and lower frequency
FETCh:OBWidth:BOBW:XDBMbandwidth:IN:LEFT:FREQuency? Returns the frequency corresponding to the X dBm value to the left
FETCh:OBWidth:BOBW:XDBMbandwidth:IN:RIGHt:FREQuency? Returns the frequency corresponding to the X dBm value to the
FETCh:OBWidth:BOBW:XDBMbandwidth:OUT:BANDwidth? Returns the difference between the higher and lower frequency
FETCh:OBWidth:BOBW:XDBMbandwidth:OUT:LEFT:FREQuency? Returns the frequency corresponding to the X dBm value to the left
FETCh:OBWidth:BOBW:XDBMbandwidth:OUT:RIGHt:FREQuency? Returns the frequency corresponding to the X dBm value to the
FETCH:P25 subgroup P25 measurements
FETCh:P25:CONSte:FERRor? Returns the frequency error.
FETCh:P25:CONSte:TRACe? Returns the display trace data.
FETCh:P25:EDIagram:FDEViation? Returns the Frequency Deviation vs Time trace data with the X
FETCh:P25:EDIagram:FERRor? Returns the frequency error.
FETCh:P25:EDIagram:I? Returns the I versus time trace data.
FETCh:P25:EDIagram:I? Returns the Q versus time trace data.
FETCh:P25:PVTime:BURSt:WIDTh? Returns the value of the measured time width of the burst packet
FETCH:P25:SUMMary:MODUlation:MEASurement:FREQuency:AC
CUracy
Table continued…
Returns the Tx address.
the Gain display.
bytes per frequency) is returned.
pointscorresponding to the value where it is X dB less from the
value at the center frequency.
points corresponding to the value which it is the X dBm value
measured inwards(coming from the ends to the center frequency).
of the center frequency measured in the inward direction.
right of the center frequency measured in the inward direction.
points corresponding to the value which it is the X dBm value
measured outwards(from the center frequency to the ends).
of the center frequency measured in the outward direction.
right of the center frequency measured in the outward direction.
value.
from poweron to powerdown (or the end of waveform, if that occurs
before powerdown), in seconds.
Returns the Operational Frequency Accuracy measurement results.
SignalVu-PC Vector Analysis Software Programmer Manual 71
Page 72
Syntax and Commands
Command Description
FETCh:P25:SUMMary:MODUlation:MEASurement:FREQuency:AC
CUracy:STATus
FETCH:P25:SUMMary:MODUlation:MEASurement:FREQuency:DE
VIation:NEGPeak
FETCh:P25:SUMMary:MODUlation:MEASurement:FREQuency:DE
VIation: NEGPeak:STATus
FETCH:P25:SUMMary:MODUlation:MEASurement:FREQuency:.D
EVIation:POSPeak
FETCh:P25:SUMMary:MODUlation:MEASurement:FREQuency:.DE
VIation:POSPeak:STATus
FETCH:P25:SUMMary:MODUlation:MEASurement:FREQuency:ER
Ror
FETCH:P25:SUMMary:MODUlation:MEASurement:SRA? Returns the Symbol Rate Accuracy measurement results.
FETCh:P25:SUMMary:MODUlation:MEASurement:SRA:STATus Returns the Symbol Rate Accuracy measurement status.
FETCh:P25:SUMMary:POWEr:MEASurement:HCPM:MAXOFF:ST
ATus?
FETCh:P25:SUMMary:POWEr:MEASurement:HCPM:MAXON:STA
Tus?
FETCh:P25:SUMMary:POWEr:MEASurement:HCPM:MAXSs:STATusReturns HCPM Pss-max measurement status.
Returns the Operational Frequency Accuracy measurement status.
Returns the Frequency Deviation, negative peak, measurement
results.
Returns the Status of Frequency Deviation, negative peak
measurement status.
Returns the status of Frequency Deviation, positive peak resutls.
Returns the status of Frequency Deviation, positive peak status.
Returns the Frequency Error measurement results.
Returns HCPM Pmax-off measurement status.
Returns Status of HCPM Pmax-on measurement status.
FETCh:P25:SUMMary:POWEr:MEASurement:HCPM:MINImum:ST
ATus?
FETCh:P25:SUMMary:POWEr:MEASurement:HCPM:OFFSlot:STA
Tus?
FETCh:P25:SUMMary:POWEr:MEASurement:HCPM:PEAK:ACPR:HIReturns P_ACP_HI value.
FETCh:P25:SUMMary:POWEr:MEASurement:HCPM:PEAK:ACPR:
LOW
FETCh:P25:SUMMary:POWEr:MEASurement:HCPM:PEAK:ACPR:
MIN
FETCh:P25:SUMMary:POWEr:MEASurement:HCPM:PEAK:ACPR:
MIN:STATus
FETCh:P25:SUMMary:POWEr:MEASurement:RF Returns RF measurement results.
FETCh:P25:SUMMary:POWEr:MEASurement:RF:STATus Returns Status of RF measurement status.
FETCH:P25:SUMMary:TRIGger:MEASurement:HCPM:TIME:ALIGN
ment:TERRor:ONE:.ACQ:COUNT?
FETCh:P25:SUMMary:TRIGger:MEASurement:HCPM:TIME:ALIGN
ment:TERRor: ONE:STATus
FETCh:P25:SUMMary:TRIGger:MEASurement:HCPM:TIME:ALIGN
ment:TERRor:.ZERO:STATus?
FETCh:P25:SUMMary:TRIGger:MEASurement:PHASe1:ATTAck:TI
ME:.ENCOder:BI:STATus?
Table continued…
Returns status of HCPM Pss-min measurement status based on the
limit.
Returns status of HCPM Offslot measurement based on the limit.
Returns P_ACP_LOW value.
Returns Min Pk ACPR value.
Returns status of Min Pk ACPR value based on the limit.
Returns the HCPM Time alignment’s t_error_1 acquisition count
over which the t_error_1 average is computed.
Returns status of HCPM Time alignment’s t_error_1 measurement
results based on the limit.
Returns status of HCPM Time alignment’s t_error_0 measurement
results.
Returns status of Average Transmitter Power Encoder Attack
Time,busy/idle, measurement status.
72
Page 73
Syntax and Commands
Command Description
FETCh:P25:SUMMary:TRIGger:MEASurement:PHASe1:ATTAck:TI
ME:.ENCOder:STATus?
FETCH:P25:SUMMary:TRIGger:MEASurement:PHASe1:ATTAck:TI
ME:.ENCOder?
FETCh:P25:SUMMary:TRIGger:MEASurement:PHASe1:ATTAck:TI
ME:POWEr:BI:STATus
FETCH:P25:SUMMary:TRIGger:MEASurement:PHASe1:ATTAck:TI
ME:POWEr:BI?
FETCh:P25:SUMMary:TRIGger:MEASurement:PHASe1:ATTAck:TI
ME:POWEr:STATus
FETCH:P25:SUMMary:TRIGger:MEASurement:PHASe1:ATTAck:TI
ME:POWEr?
FETCH:P25:SUMMary:TRIGger:MEASurement:PHASe1:THRUput:
DELAy:ACQ:COUNT?
FETCh:P25:SUMMary:TRIGger:MEASurement:PHASe1:THRUput:
DELAy:STATus
FETCH:P25:SUMMary:TRIGger:MEASurement:PHASe1:THRUput:
DELAy?
FETCH:P25:SUMMary:POWEr:MEASurement:HCPM:MAXOFF? Returns the HCPM Pmax-off measurement results.
FETCH:P25:SUMMary:POWEr:MEASurement:HCPM:MAXON? Returns the HCPM Pmax-on measurement results.
FETCH:P25:SUMMary:POWEr:MEASurement:HCPM:MAXSS? Returns the HCPM Pss-max measurement results.
FETCH:P25:SUMMary:POWEr:MEASurement:HCPM:MINImum? Returns the HCPM Pss-min measurement results.
FETCH:P25:SUMMary:POWEr:MEASurement:HCPM:OFFSlot? Returns the HCPM Offslot power results.
FETCH:P25:SUMMary:TRIGger:MEASurement:HCPM:TIME:ALIGN
ment:TERRor:ONE?
FETCh:P25:SUMMary:TRIGger:MEASurement:HCPM:TIME:ALIGN
ment:TERRor:ONE:.ACQ:COUNT?
FETCH:P25:SUMMary:TRIGger:MEASurement:HCPM:TIME:ALIGN
ment:TERRor:ZERO?
FETCh:P25:SUMMary:TRIGger:MEASurement:HCPM:TIME:ALIGN
ment:TERRor: ZERO:ACQ:COUNT
FETCH:P25:SUMMary:TRIGger:MEASurement:HCPM:TIME:ALIGN
ment:TOBSync?
FETCh:P25:SUMMary:TRIGger:MEASurement:HCPM:TIME:ALIGN
ment: TOBSync:ACQ:COUNT
FETCh:P25:SUMMary:TRIGger:MEASurement:PHASe1:ATTAck:TI
ME:ACQ:COUNT
FETCH:P25:SUMMary:TRIGger:MEASurement:PHASe1:ATTAck:TI
ME:ACQ:.COUNT:BI?
FETCH:P25:SUMMary:TRIGger:MEASurement:PHASe1:ATTAck:TI
ME:ENCOder?
Table continued…
Returns status of Average Transmitter Encoder Attack Time
measurement results based on the limit.
Returns the Average Transmitter Encoder Attack Time
measurement results.
Returns status of Average Transmitter Power Attack Time, busy/
idle,measurement results based on the limit.
Returns the Average Transmitter Power Attack Time, busy/
idle,measurement results.
Returns status of Average Transmitter Power Attack Time
measurement results.
Returns the Average Transmitter Power Attack Time measurement
results.
Returns the Throughput delay acquisition counts over which the
Throughput delay average is computed.
Returns status of Throughput delay measurement results based on
the limit.
Returns the Throughput delay measurement results.
Returns the HCPM Time alignment’s t_error_1 measurement
results.
Returns the HCPM Time alignment’s t_error_1 acquisition count
over which the t_error_1 average is computed.
Returns the HCPM Time alignment’s t_error_0 measurement
results.
Returns the HCPM Time alignment’s t_error_0 acquisition count
over which the t_error_0 average is done.
Returns the HCPM Time alignment’s t_obsync measurement
results.
Returns the HCPM Time alignment’s t_obsync acquisition counts
over which the t_obsync average is computed.
Returns the Average Transmitter Power Attack acquisition count
over which the t_obsync average is computed.
Returns the Average Transmitter Power Attack, busy/idle,
acquisition count over which the Busy/Idle Attack time average is
computed.
Returns the Average Transmitter Encoder Attack Time
measurement results.
SignalVu-PC Vector Analysis Software Programmer Manual 73
Page 74
Syntax and Commands
Command Description
FETCH:P25:SUMMary:TRIGger:MEASurement:PHASe1:ATTAck:TI
ME:ENCOder:BI?
FETCh:P25:SUMMary:TRIGger:MEASurement:PHASe1:ATTAck:TI
ME:POWEr
FETCh:P25:SUMMary:TRIGger:MEASurement:PHASe1:ATTAck:TI
ME:POWEr:BI
FETCh:P25:SUMMary:TRIGger:MEASurement:PHASe1:THRUput:
DELAy
FETCh:P25:SUMMary:TRIGger:MEASurement:PHASe1:THRUput:
DELAy:ACQ:COUNT
FETCh:RFIN subgroup RF acquisition data
FETCh:RFIN:IQ:HEADer? Returns the header information for a specific acquisition data
FETCh:RFIN:IQ:SCALe? Returns the scaling factor contained in the .tiq file header.
FETCh:RFIN:RECord:IDS? Returns the beginning and end ID numbers of acquisition data.
FETCh:ACPower subgroup Channel power and ACPR measurement
FETCh:ACPower? Returns the ACPR measurement results.
FETCh:ACPower:CHANnel:POWer? Returns the average power of the main channel.
FETCh:ACPower:SPECtrum? Returns spectrum trace data of the ACPR measurement.
FETCh:FM:PNEGative? Returns the negative peak frequency deviation (–Pk).
FETCh:FM:PPOSitive? Returns the positive peak frequency deviation (+Pk).
FETCh:FM:PTPeak? Returns the peak-peak frequency deviation (Pk-Pk).
FETCh:FM:RESult? Returns the FM measurement results.
FETCh:FM:RMS? Returns the RMS frequency deviation.
FETCh:PM:PNEGative? Returns the negative peak phase deviation (–Pk).
FETCh:PM:PPOSitive? Returns the negative peak phase deviation (–Pk).
FETCh:PM:PTPeak? Returns the peak-peak phase deviation (Pk-Pk).
FETCh:PM:RESult? Returns the PM measurement results.
FETCh:PM:RMS? Returns the PM measurement results.
FETCh:AUDio subgroup Audio measuremt
FETCh:AUDio:FERRor? Returns the carrier frequency error in the audio measurement.
FETCh:AUDio:FREQuency? Returns the audio frequency.
FETCh:AUDio:HARMonic:COUNt? Returns the number of harmonics in the audio spectrum
FETCh:AUDio:HARMonic<x>:AMPLitude? Returns the amplitude of the specified harmonic in the audio
FETCh:AUDio:HARMonic<x>:FREQuency? Returns the frequency of the specified harmonic in the audio
FETCh:AUDio:HNOise? Returns the difference between the current RMS modulation value
Table continued…
Returns the Average Transmitter Encoder Attack Time, busy/
idle,measurement results.
Returns the Average Transmitter Power Attack Time measurement
results.
Returns the Average Transmitter Power Attack Time, busy/
idle,measurement results.
Returns the Throughput delay measurement results.
Returns the Throughput delay acquisition counts over which the
Throughput delay average is computed.
record.
measurement.
spectrum measurement.
spectrum measurement.
and the reference value.
74
Page 75
Syntax and Commands
Command Description
FETCh:AUDio:HNREFerence? Returns the Hum and Noise RMS modulation reference value.
FETCh:AUDio:HPTPeak? Returns the half peak-to-peak modulation excursion.
FETCh:AUDio:MODDist? Returns the modulation distortion for the audio measurement.
FETCh:AUDio:NHARmonic:COUNt? Returns the number of non-harmonics in the audio spectrum
measurement.
FETCh:AUDio:NHARmonic<x>:AMPLitude? Returns the amplitude of the specified non-harmonic in the audio
spectrum measurement.
FETCh:AUDio:NHARmonic<x>:FREQuency? Returns the frequency of the specified non-harmonic in the audio
spectrum measurement.
FETCh:AUDio:PNEGative? Returns the minus peak modulation excursion.
FETCh:AUDio:POWer? Returns the carrier power or signal power depending the signal
type.
FETCh:AUDio:PPOSitive? Returns the positive peak modulation excursion.
FETCh:AUDio:RMS? Returns the RMS modulation excursion for the audio measurement.
FETCh:AUDio:SINad? Returns the signal-to-noise and distortion for the audio
measurement.
FETCh:AUDio:SNOise? Returns the signal level to noise level with the harmonic distortion
and non-harmonic distortion components removed.
FETCh:AUDio:SPECtrum:TRACe<x>? Returns the audio spectrum trace data for the audio measurement.
FETCh:AUDio:THDist? Returns the percentage of the total harmonic distortion.
FETCh:AUDio:THDist:DB? Returns the total harmonic distortion in dB in the audio
measurement.
FETCh:AUDio:TNHDist? Returns the percentage of the total harmonic distortion in the audio
measurement.
FETCh:AUDio:TNHDist:DB? Returns the total non-harmonic distortion in dB in the audio
measurement.
FETCh:AUDio:TNHDist? Returns the percentage of the total non-harmonic distortion in the
audio measurement.
FETCh:AVTime subgroup Amplitude versus Time measurement
FETCh:AVTime[:MEASview<y>]:AVERage? Returns the RMS value.
FETCh:AVTime[:MEASview<y>]:{FIRSt|SECond|THIRd|FOURth}? Returns the trace data.
FETCh:AVTime[:MEASview<y>]:MAXLocation? Returns the maximum value.
FETCh:AVTime[:MEASview<y>]:MAXLocation? Returns the time at the maximum.
FETCh:AVTime[:MEASview<y>]:MINimum? Returns the minimum value.
FETCh:AVTime[:MEASview<y>]:MINLocation? Returns the time at the minimum.
FETCh:AVTime[:MEASview<y>]:RESult? Returns the measurement results.
FETCh:CCDF subgroup CCDF measurement
FETCh:CCDF? Returns the CCDF measurement results.
FETCh:CCDF:{FIRSt|SECond|THIRd}:X? Returns the horizontal values of the specified trace.
FETCh:CCDF:{FIRSt|SECond|THIRd}:XY? Returns the horizontal and vertical value pairs of the specified trace.
Table continued…
SignalVu-PC Vector Analysis Software Programmer Manual 75
Page 76
Syntax and Commands
Command Description
FETCh:CCDF:{FIRSt|SECond|THIRd}[:Y]? Returns the vertical values of the specified trace.
FETCh:CONSte subgroup (Option 21 only) Constellation measurement
FETCh:CONSte:FERRor? Returns the frequency error in Hz.
FETCh:CONSte:RESults? Returns the constellation measurement results.
FETCh:CONSte:TRACe? Returns the constellation trace data.
FETCh:DDEMod subgroup (Option 21 only) General purpose digital modulation measurements
FETCh:DDEMod:STABle? Returns the symbol table data.
FETCh:DDEMod:SYNCh:WORD:LENGth? Returns the length of the synch word in the symbol table.
FETCh:DDEMod:SYNCh:WORD:POSition? Returns the position of the synch word in the symbol table.
FETCh:DIQVtime subgroup (Option 21 only) Demodulated I&Q versus Time measurement
FETCh:DIQVtime:FERRor? Returns the frequency error.
FETCh:DIQVtime:I? Returns the I versus Time trace data.
FETCh:DIQVtime:Q? Returns the Q versus Time trace data.
FETCh:DPX subgroup DPX spectrum measurement
FETCh:DPX:DDENsity? Returns the calculated density for the selected region in the
DPXogram measurement.
FETCh:DPX:DGRam:LINE:COUNt? Returns the number of lines in the DPXogram measurement.
FETCh:DPX:DGRam:TIME[:SCALe]:OFFSet? Returns the time scale offset in the DPXogram measurement.
FETCh:DPX:RESults:TRACe<x>? Returns waveform data in the DPX spectrum measurement.
FETCh:DPX:TDM:FREQuency:TXBer:BER? Returns the Tx BER measurement BER results.
FETCh:DPX:TDM:FREQuency:TXBer:BITS? Returns the number of bits counted in the active Tx BER
measurement session.
FETCh:DPX:TDM:FREQuency:TXBer:ERRors? Returns the number of errors counted in the active Tx BER
measurement session.
FETCh:DPX:TDM:FREQuency:TXBer:STATe? Returns the state of the Tx BER measurement.
FETCh:DPX:TRACe:AVERage? Returns waveform data of the average trace in the DPX spectrum
measurement.
FETCh:DPX:TRACe:BITMap? Returns trace waveform data of the bitmap trace.
FETCh:DPX:TRACe:MATH? Returns waveform data of the math trace.
FETCh:DPX:TRACe:MAXimum? Returns waveform data of the maximum trace.
FETCh:DPX:TRACe:MINimum? Returns waveform data of the minimum trace.
FETCh:EDIagram subgroup (Option 21 only) Eye diagram
FETCh:EDIagram:FDEViation? Returns the frequency deviation versus Time trace data.
FETCh:EDIagram:FERRor? Returns the frequency error.
FETCh:EDIagram:I? Returns the I versus Time trace data.
FETCh:EDIagram:Q? Returns the Q versus Time trace data.
FETCh:EVM subgroup (Option 21 only) EVM versus Time measurement
FETCh:EVM:FERRor? Returns the frequency error.
Table continued…
76
Page 77
Syntax and Commands
Command Description
FETCh:EVM:PEAK? Returns the peak value.
FETCh:EVM:PINDex? Returns the time at the EVM peak.
FETCh:EVM:RMS? Returns the RMS value.
FETCh:EVM:TRACe? Returns the EVM versus Time trace data.
FETCh:FDVTime subgroup (Option 21 only) Frequency deviation versus Time measurement
FETCh:FDVTime:FERRor? Returns the frequency error in the Frequency deviation versus Time
measurement.
FETCh:FDVTime:TRACe? Returns the Frequency deviation versus Time trace data.
FETCh:{FSETtling|PSETtling} subgroup (Option 12 only) Frequency and Phase Settling measurements
FETCh:FSETtling:ERRor? Returns the settled error in Hz in Frequency Settling.
FETCh:{FSETtling|PSETtling}:FTTime? Returns the settling time from the trigger position in seconds.
FETCh:{FSETtling|PSETtling}:MASK[:PASS]? Returns whether the input signal passes the mask test.
FETCh:{FSETtling|PSETtling}:SETTled:FREQuency? Returns the frequency at which the signal is considered settled.
FETCh:{FSETtling|PSETtling}:SETTled[:PASS]? Returns whether the input signal is settled with the tolerance range.
FETCh:{FSETtling|PSETtling}:SETTled:TIME? Returns the settled time in seconds.
FETCh:{FSETtling|PSETtling}:SLMSd[:PASS]? Returns whether the input signal is settled within the specified
tolerance and the signal is settled longer than the Minimum Settled
Duration.
FETCh:{FSETtling|PSETtling}:STARt:TIME? Returns the start time for the measurement in seconds.
FETCh:{FSETtling|PSETtling}:TIME? Returns the settling time in seconds. The settling time is measured
from the start time.
FETCh:{FSETtling|PSETtling}:TRACe<x>:X? Returns the settling time in seconds. The settling time is measured
from the start time.
FETCh:{FSETtling|PSETtling}:TRACe<x>:XY? Returns the time and frequency or phase value pairs of the
specified trace.
FETCh:{FSETtling|PSETtling}:TRACe<x>[:Y]? Returns the frequency or phase values of the specified trace.
FETCh:{FSETtling|PSETtling}:TRIGger:TIME? Returns the time when the trigger occurred in seconds.
FETCh:{FSETtling|PSETtling}:VALue? Returns the settled value in Hz for Frequency Settling and in
degrees for Phase Settling.
FETCh:FVTime subgroup Frequency versus Time measurement
FETCh:FVTime[:MEASview<y>]? Returns the Frequency versus Time trace data.
FETCh:FVTime[:MEASview<y>]:MAXimum? Returns the maximum value.
FETCh:FVTime[:MEASview<y>]:MAXLocation? Returns the time at which the frequency drift is maximum.
FETCh:FVTime[:MEASview<y>]:MINimum? Returns the minimum value.
FETCh:FVTime[:MEASview<y>]:MINLocation? Returns the time at which the frequency drift is minimum.
FETCh:FVTime[:MEASview<y>]:RESult? Returns the measurement results.
FETCh:IQVTime subgroup RF I&Q versus Time measurement
FETCh:IQVTime[:MEASview<y>]:I? Returns the I versus Time trace data.
FETCh:IQVTime[:MEASview<y>]:MAXimum? Returns the maximum value.
Table continued…
SignalVu-PC Vector Analysis Software Programmer Manual 77
Page 78
Syntax and Commands
Command Description
FETCh:IQVTime[:MEASview<y>]:MAXLocation? Returns the time at which the I or Q level is maximum.
FETCh:IQVTime[:MEASview<y>]:MINimum? Returns the minimum value.
FETCh:IQVTime[:MEASview<y>]:MINLocation? Returns the time at which the I or Q level is minimum.
FETCh:IQVTime[:MEASview<y>]:Q? Returns the Q versus Time trace data.
FETCh:IQVTime[:MEASview<y>]:RESult? Returns the measurement results.
FETCh:MCPower subgroup MCPR measurement
FETCh:MCPower:ADJacent:CHANnels? Returns the power of adjacent channels.
FETCh:MCPower:CHANnel:POWer? Returns the reference power.
FETCh:MCPower:MAIN:CHANnels? Returns the power of main channels.
FETCh:MCPower:SPECtrum? Returns spectrum trace data.
FETCh:MERRor subgroup (Option 21 only) Magnitude error versus Time measurement
FETCh:MERRor:FERRor? Returns the frequency error.
FETCh:MERRor:PEAK? Returns the peak value.
FETCh:MERRor:PINDex? Returns the time at the magnitude error peak.
FETCh:MERRor:RMS? Returns the RMS value.
FETCh:MERRor:TRACe? Returns the Magnitude error versus Time trace data.
FETCh:OBWidth subgroup Occupied Bandwidth measurement
FETCh:OBWidth:BOBW:FREQuency:ERRor Returns the frequency error.
FETCh:OBWidth:BOBW:RESUlts:STATus Returns the test result as Pass or Fail.
FETCh:OBWidth:BOBW:XDBB:POWer Returns the dB BW reference power.
FETCh:OBWidth:FREQuency:ERRor? Returns the frequency error.
FETCh:OBWidth:OBWidth:BANDwidth? Returns the occupied bandwidth.
FETCh:OBWidth:OBWidth:LEFT:FREQuency? Returns the left (lower) frequency of the occupied bandwidth.
FETCh:OBWidth:OBWidth:LEFT:LEVel? Returns the level at the left frequency of the occupied bandwidth.
FETCh:OBWidth:OBWidth:POWer? Returns the reference power in the Occupied Bandwidth
measurement.
FETCh:OBWidth:OBWidth:RIGHt:FREQuency? Returns the right (higher) frequency of the occupied bandwidth.
FETCh:OBWidth:OBWidth:RIGHt:LEVel? Returns the level at the right frequency of the occupied bandwidth.
FETCh:OBWidth:SPECtrum? Returns spectrum trace data of the Occupied Bandwidth
measurement.
FETCh:OBWidth:XDBBandwidth:BANDwidth? Returns the x dB bandwidth.
FETCh:OBWidth:XDBBandwidth:LEFT:FREQuency? Returns the left (lower) frequency of the x dB bandwidth.
FETCh:OBWidth:XDBBandwidth:LEFT:LEVel? Returns the level at the left frequency of the x dB bandwidth.
FETCh:OBWidth:XDBBandwidth:POWer? Returns the reference power in the x dB bandwidth measurement.
FETCh:OBWidth:XDBBandwidth:RIGHt:FREQuency? Returns the right (higher) frequency of the x dB bandwidth.
FETCh:OBWidth:XDBBandwidth:RIGHt:LEVel? Returns the level at the right frequency of the x dB bandwidth.
FETCh:OFDM subgroup Orthogonal Frequency Division Multiplexing measurement
FETCh:OFDM:APOWer? Returns the average power.
Table continued…
78
Page 79
Syntax and Commands
Command Description
FETCh:OFDM:APOWer:PEAK? Returns the peak-to-average power.
FETCh:OFDM:CONSte:MAGNitude? Returns the constellation magnitude data.
FETCh:OFDM:CONSte:PHASe? Returns the constellation phase values.
FETCh:OFDM:CONSte:TYPE? Returns the constellation context value.
FETCh:OFDM:CONSte:VALue? Returns the constellation value.
FETCh:OFDM:CPE? Returns the Common Pilot Error magnitude.
FETCh:OFDM:CRESponse:MAGNitude? Returns the channel response magnitude data.
FETCh:OFDM:CRESponse:PHASe? Returns the channel response phase data.
FETCh:OFDM:EVM:PEAK:DECibel:ALL? Returns the peak EVM data for all subcarriers.
FETCh:OFDM:EVM:PEAK:DECibel:DATA? Returns the peak EVM data for the data subcarriers.
FETCh:OFDM:EVM:PEAK:DECibel:PILots? Returns the peak EVM data for the pilot subcarriers.
FETCh:OFDM:EVM:PEAK:PERCent:ALL? Returns the peak EVM data for all subcarriers.
FETCh:OFDM:EVM:PEAK:PERCent:DATA? Returns the peak EVM data for the data subcarriers.
FETCh:OFDM:EVM:PEAK:PERCent:PILots? Returns the peak EVM data for the pilot subcarriers.
FETCh:OFDM:EVM:PEAK:SCARrier:ALL? Returns the peak EVM data for all subcarriers.
FETCh:OFDM:EVM:PEAK:SCARrier:DATA? Returns the peak EVM data for all data subcarriers.
FETCh:OFDM:EVM:PEAK:SCARrier:PILots? Returns the peak EVM data for the pilot subcarriers.
FETCh:OFDM:EVM:PEAK:SYMBol:ALL? Returns the peak EVM data for all subcarriers.
FETCh:OFDM:EVM:PEAK:SYMBol:DATA? Returns the peak EVM data for the data subcarriers.
FETCh:OFDM:EVM:PEAK:SYMBol:PILots? Returns the peak EVM data for the pilot subcarriers.
FETCh:OFDM:EVM:RMS:DECibel:ALL? Returns the RMS EVM data for all subcarriers
FETCh:OFDM:EVM:RMS:DECibel:DATA? Returns the RMS EVM data for the data subcarriers.
FETCh:OFDM:EVM:RMS:DECibel:PILots? Returns the RMS EVM data for the pilot subcarriers.
FETCh:OFDM:EVM:RMS:PERCent:ALL? Returns the peak RMS data for all subcarriers
FETCh:OFDM:EVM:RMS:PERCent:DATA? Returns the peak RMS data for the data subcarriers.
FETCh:OFDM:EVM:RMS:PERCent:PILots? Returns the peak RMS data for the pilot subcarriers.
FETCh:OFDM:EVM:TRACe<x>? Returns the EVM trace data.
FETCh:OFDM:FERRor? Returns the Frequency error reading.
FETCh:OFDM:FLATness:PASS? Verifies the average power levels of the subcarriers remain within
the limits defined for a particular standard.
FETCh:OFDM:FLATness:RESult? Returns the summary results of each segment.
FETCh:OFDM:FLATness:TRACe<x>? Returns the OFDM Spectral Flatness trace data.
FETCh:OFDM:GAIN:IMBalance? Returns the gain imbalance.
FETCh:OFDM:IQ:ORIGin:OFFSet? Returns the IQ origin offset.
FETCh:OFDM:MERRor:TRACe<x>? Returns the magnitude error trace data.
FETCh:OFDM:PACKet:DIRection? Returns the direction of the packet.
FETCh:OFDM:PERRor:TRACe<x>? Returns the phase error trace data.
Table continued…
SignalVu-PC Vector Analysis Software Programmer Manual 79
Page 80
Syntax and Commands
Command Description
FETCh:OFDM:POWer:TRACe<x>? Returns the power trace data.
FETCh:OFDM:QUADrature:OFFSet? Returns the quadrature offset.
FETCh:OFDM:SCARriers? Returns the number of subcarriers.
FETCh:OFDM:SCARriers:SPACing? Returns the subcarrier spacing.
FETCh:OFDM:STABle:VALUe? Returns the number of bytes in the symbol table.
FETCh:OFDM:SYMBol:CERRor? Returns the symbol clock error.
FETCh:OFDM:SYMBol:COUNt? Returns the number of symbols.
FETCh:PERRor subgroup (Option 21 only) Phase error versus Time measurement
FETCh:PERRor:FERRor? Returns the frequency error.
FETCh:PERRor:PEAK? Returns the peak value.
FETCh:PERRor:PINDex? Returns the time at the phase error peak.
FETCh:PERRor:RMS? Returns the RMS value.
FETCh:PERRor:TRACe? Returns the Phase error versus Time trace data.
FETCh:PHVTime subgroup Phase versus Time measurement
FETCh:PHVTime[:MEASview<y>]? Returns the Phase versus Time trace data.
FETCh:PHVTime[:MEASview<y>]:MAXimum? Returns the maximum value.
FETCh:PHVTime[:MEASview<y>]:MAXLocation? Returns the time at which the phase is maximum.
FETCh:PHVTime[:MEASview<y>]:MINimum? Returns the minimum value.
FETCh:PHVTime[:MEASview<y>]:MINLocation? Returns the time at which the phase is minimum.
FETCh:PHVTime[:MEASview<y>]:RESult? Returns the results.
FETCh:PNOise subgroup (Option 11 only) Phase noise measurements
FETCh:PNOise:ALL? Returns all the measurement results.
FETCh:PNOise:CARRier:FERRor? Returns the carrier frequency error.
FETCh:PNOise:CARRier:POWer? Returns the carrier power.
FETCh:PNOise:RESidual:FM? Returns the residual FM.
FETCh:PNOise:RMS:PNOise? Returns the RMS phase noise.
FETCh:PNOise:SPECtrum<x>:X? Returns the frequencies of the specified trace.
FETCh:PNOise:SPECtrum<x>:XY? Returns the frequency and phase noise pairs of the specified trace.
FETCh:PNOise:SPECtrum<x>[:Y]? Returns the phase noise values of the specified trace.
FETCh:PNOise:JITTer? Returns the jitter.
FETCh:PULSe subgroup Pulsed RF measurements
FETCh:PULSe[:RESult][:MEASview<y>]:ATX? Returns the average transmitted power in the results table.
FETCh:PULSe[:RESult][:MEASview<y>]:AVERage? Returns the average on power in the results table.
FETCh:PULSe[:RESult][:MEASview<y>]:DRODb? Returns the droop in dB in the pulse table.
FETCh:PULSe[:RESult][:MEASview<y>]:DROop? Returns the droop in the pulse table
FETCh:PULSe[:RESult][:MEASview<y>]:DUTPct? Returns the duty factor (%) in the results table.
FETCh:PULSe[:RESult][:MEASview<y>]:DUTRatio? Returns the duty factor (ratio) in the results table.
Table continued…
80
Page 81
Syntax and Commands
Command Description
FETCh:PULSe[:RESult][:MEASview<y>]:FALL? Returns the fall time in the results table.
FETCh:PULSe[:RESult][:MEASview<y>]:FDELta? Returns the delta frequency in the results table.
FETCh:PULSe[:RESult][:MEASview<y>]:FRDeviation? Returns the frequency deviation in the results table.
FETCh:PULSe[:RESult][:MEASview<y>]:IRAMplitude? Returns the pulse impulse response amplitude measurement in the
pulse table.
FETCh:PULSe[:RESult][:MEASview<y>]:IRTime? Returns the impulse response time in the pulse table.
FETCh:PULSe[:RESult][:MEASview<y>]:MFReqerror? Returns the maximum frequency error in the results table.
FETCh:PULSe[:RESult][:MEASview<y>]:MPHerror? Returns the maximum phase error in the results table.
FETCh:PULSe[:RESult][:MEASview<y>]:OVEDb? Returns the overshoot in dB in the pulse table.
FETCh:PULSe[:RESult][:MEASview<y>]:OVERshoot? Returns the overshoot in the pulse table.
FETCh:PULSe[:RESult][:MEASview<y>]:PHDeviation? Returns the phase deviation in the results table.
FETCh:PULSe[:RESult][:MEASview<y>]:PPFRequency? Returns the pulse-pulse carrier frequency in the results table.
FETCh:PULSe[:RESult][:MEASview<y>]:PPOWer? Returns the peak power in the results table.
FETCh:PULSe[:RESult][:MEASview<y>]:PPPHase? Returns the pulse-pulse carrier phase in the results table.
FETCh:PULSe[:RESult][:MEASview<y>]:RINTerval? Returns the repetition interval in the results table.
FETCh:PULSe[:RESult][:MEASview<y>]:RIPDb? Returns the ripple in dB in the pulse table.
FETCh:PULSe[:RESult][:MEASview<y>]:RIPPle? Returns the ripple in the pulse table.
FETCh:PULSe[:RESult][:MEASview<y>]:RISE? Returns the rise time in the results table.
FETCh:PULSe[:RESult][:MEASview<y>]:RMSFreqerror? Returns the RMS frequency error in the results table.
FETCh:PULSe[:RESult][:MEASview<y>]:RMSPherror? Returns the RMS phase error in the results table.
FETCh:PULSe[:RESult][:MEASview<y>]:RRATe? Returns the repetition rate in the results table.
FETCh:PULSe[:RESult][:MEASview<y>]:TIME? Returns the time in the results table.
FETCh:PULSe[:RESult][:MEASview<y>]:WIDTh? Returns the pulse width in the results table.
FETCh:PULSe:STATistics[:MEASview<y>]:ATX? Returns the average transmitted power of the statistics.
FETCh:PULSe:STATistics[:MEASview<y>]:AVERage? Returns the average on power of the statistics.
FETCh:PULSe:STATistics[:MEASview<y>]:DRODb? Returns the droop in dB of the statistics.
FETCh:PULSe:STATistics[:MEASview<y>]:DROop? Returns the droop of the statistics
FETCh:PULSe:STATistics[:MEASview<y>]:DUTPct? Returns the duty factor (%) of the statistics.
FETCh:PULSe:STATistics[:MEASview<y>]:DUTRatio? Returns the duty factor (ratio) of the statistics.
FETCh:PULSe:STATistics[:MEASview<y>]:FALL? Returns the fall time of the statistics.
FETCh:PULSe:STATistics:[:MEASview<y>]FDELta? Returns the delta frequency measurement statistics.
FETCh:PULSe:STATistics[:MEASview<y>]:FRDeviation? Returns the frequency deviation of the statistics.
FETCh:PULSe:STATistics[:MEASview<y>]:IRAMplitude? Returns the Pulse Impulse Response amplitude measurement in
the pulse statistics.
FETCh:PULSe:STATistics[:MEASview<y>]:IRTime? Returns the impulse response time in the pulse statistics.
FETCh:PULSe:STATistics[:MEASview<y>]:MFReqerror? Returns the maximum frequency error of the statistics.
FETCh:PULSe:STATistics[:MEASview<y>]:MPHerror? Returns the maximum phase error of the statistics.
Table continued…
SignalVu-PC Vector Analysis Software Programmer Manual 81
Page 82
Syntax and Commands
Command Description
FETCh:PULSe:STATistics[:MEASview<y>]:OVEDb? Returns the overshoot measurement result in dB in the pulse
statistics.
FETCh:PULSe:STATistics[:MEASview<y>]:OVERshoot? Returns the overshoot measurement result in the pulse statistics.
FETCh:PULSe:STATistics[:MEASview<y>]:PHDeviation? Returns the phase deviation of the statistics.
FETCh:PULSe:STATistics[:MEASview<y>]:PPFRequency? Returns the pulse-pulse carrier frequency of the statistics.
FETCh:PULSe:STATistics[:MEASview<y>]:PPOWer? Returns the peak power of the statistics.
FETCh:PULSe:STATistics[:MEASview<y>]:PPPHase? Returns the pulse-pulse carrier phase of the statistics.
FETCh:PULSe:STATistics[:MEASview<y>]:RINTerval? Returns the repetition interval of the statistics.
FETCh:PULSe:STATistics[:MEASview<y>]:RIPDb? Returns the ripple in dB of the statistics.
FETCh:PULSe:STATistics[:MEASview<y>]:RIPPle? Returns the ripple of the statistics.
FETCh:PULSe:STATistics[:MEASview<y>]:RISE? Returns the rise time of the statistics.
FETCh:PULSe:STATistics[:MEASview<y>]:RMSFreqerror? Returns the RMS frequency error of the statistics.
FETCh:PULSe:STATistics[:MEASview<y>]:RMSPherror? Returns the RMS phase error of the statistics.
FETCh:PULSe:STATistics[:MEASview<y>]:RRATe? Returns the repetition rate of the statistics.
FETCh:PULSe:STATistics[:MEASview<y>]:WIDTh? Returns the pulse width in the pulse statistics.
FETCh:PULSe:STATistics[:MEASview<y>]:X? Returns the horizontal values of the trace data.
FETCh:PULSe:STATistics[:MEASview<y>]:XY? Returns the horizontal and vertical values of the trace data.
FETCh:PULSe:STATistics[:MEASview<y>][:Y]? Returns the vertical values of the trace data.
FETCh:PULSe:TRACe[:MEASview<y>]:X? Returns the time values of the pulse trace.
FETCh:PULSe:TRACe[:MEASview<y>]:XY? Returns the horizontal (time) and vertical value pairs of the pulse
trace.
FETCh:PULSe:TRACe[:MEASview<y>][:Y]? Returns the vertical values of the pulse trace.
FETCh:PULSe:CUMulative:HISTogram[:MEASview<y>]:OUTLier:
HIGHer?
FETCh:PULSe:CUMulative:HISTogram[:MEASview<y>]:OUTLier:
LOWer?
FETCh:PULSe:CUMulative:HISTogram[:MEASview<y>]:PULse:
COUNt?
FETCh:PULSe:CUMulative:HISTogram[:MEASview<y>]:PULse:TO
Tal?
FETCh:PULSe:CUMulative:STATistics[:MEASview<y>] Returns the PulseCount, Max, Max TimeStamp, Min, Min
FETCh:PULSe:OGRAm[:MEASview<y>]:MAX:FRAMe:COUNt Returns the frame count value.
FETCh:PULSe:OGRAm[:MEASview<y>]:RBW Returns the resolution bandwidth value only when Frequency vs
FETCh:PULSe[:RESult][:MEASview<y>]:ADVanced Returns the Pulse Count, Max, Max at Pulse number, Min, Min
FETCh:PULSe[:RESult][:MEASview<y>]:FABS? Returns the computed absolute frequency from the carrier.
Table continued…
Returns the outliers value exceeding the upper limit.
Returns the outliers value below the lower limit.
Returns the number of pulses in the bin.
Returns the total number of pulses.
TimeStamp, Peak to Peak, Average and Standard Deviation values
for the chosen measurement.
Time display is opened in the Pulse-Ogram display.
at Pulse number, Peak to Peak, Average and Standard Deviation
values for the chosen measurement.
82
Page 83
Syntax and Commands
Command Description
FETCh:PULSe[:RESult][:MEASview<y>]:PPFD? Returns the computed pulse to pulse frequency difference from the
carrier.
FETCh:PULSe[:RESult][:MEASview<y>]:PPPD? Returns the computed pulse to pulse phase difference from the
carrier.
FETCh:PULSe:STATistics[:MEASview<y>]:ADVanced Returns the Pulse Count, Max, Max at Pulse number, Min, Min
at Pulse number, Peak to Peak, Average and Standard Deviation
values for the chosen measurement.
FETCh:PULSe:STATistics[:MEASview<y>]:FABS Returns the absolute frequency.
FETCh:PULSe:STATistics[:MEASview<y>]:MAX:PULSe:NUMber Returns the maximum value at a certain pulse number.
FETCh:PULSe:STATistics[:MEASview<y>]:MIN:PULSe:NUMber? Returns the minimum value at a certain pulse number.
FETCh:PULSe:STATistics[:MEASview<y>]:PPFD Returns the pulse-pulse frequency difference.
FETCh:PULSe:STATistics[:MEASview<y>]:PPPD Returns the pulse-pulse phase difference.
FETCh:[RF]:PRESelector subgroup Preselector for RSA7100A
FETCh:INPut[:RF]:PRESelector:STATe Sets or queries the Preselector setting, which uses input filters for
image suppression.
FETCh:RFIN subgroup All measurements
FETCh:RFIN:IQ? Returns time-domain IQ data for a specific acquisition data record.
FETCh:RFIN:IQ:HEADer? Returns the header information for a specific acquisition data
record.
FETCh:RFIN:IQ:SCALe? Returns the internal RF linear data scaling factor contained in
the .tiq file header
FETCh:RFIN:IQ:VHEader? Returns the verbose header information for a specific acquisition
data record.
FETCh:RFIN:RECord:IDS? Returns the beginning and end ID numbers of acquisition data.
FETCh:SEM subgroup Spectral Emissions Mask measurements
FETCh:SEM:MHITs:COUNt? Returns the number of rows in the results table
FETCh:SEM:MHITs<x>:AMPLitude:ABSolute? Returns the absolute amplitude of the specified mask hit signal.
FETCh:SEM:MHITs<x>:AMPLitude:RELative? Returns the relative amplitude of the specified mask hit signal.
FETCh:SEM:MHITs<x>:FREQuency? Returns the frequency of the specified mask hit signal.
FETCh:SEM:MHITs<x>:INTeg:ABSolute? Returns the absolute integration amplitude of the specified mask hit
signal.
FETCh:SEM:MHITs<x>:INTeg:RELative? Returns the relative integration amplitude of the specified mask hit
signal.
FETCh:SEM:MHITs<x>:MARGin:ABSolute? Returns the absolute margin for the specified mask hit signal.
FETCh:SEM:MHITs<x>:MARGin:RELative? Returns the relative margin for the specified mask hit signal.
FETCh:SEM:MHITs<x>:OFFSet? Returns the offset for the specified mask hit signal.
FETCh:SEM:PASS? Returns the pass/fail limit test result.
FETCh:SEM:REF:POWer? Returns the reference power level.
FETCh:SEM:SPECtrum:X? Returns the frequencies of the spectrum trace.
FETCh:SEM:SPECtrum:XY? Returns the frequency and amplitude pairs of the spectrum trace.
Table continued…
SignalVu-PC Vector Analysis Software Programmer Manual 83
Page 84
Syntax and Commands
Command Description
FETCh:SEM:SPECtrum[:Y]? Returns the amplitude of the spectrum trace.
FETCh:SGRam subgroup Spectrogram measurement
FETCh:SGRam? Returns the spectrogram trace data.
FETCh:SIGNalvu subgroup Signal measurement
FETCh:SIGNalvu:ACQuisition:COUPling Returns the coupling value of the acquisition.
FETCh:SIGNalvu:ACQuisition:MAX:RT:BW Returns the maximum real time bandwidth value of the instrument.
FETCh:SIGNalvu:ACQuisition:TERMination Returns the termination value of the acquisition.
FETCh:SPECtrum subgroup Spectrum measurement
FETCh:SPECtrum:TRACe<x>? Returns the trace data in the Spectrum Analyzer measurement.
FETCh:SPURious subgroup Spurious measurement
FETCh:SPURious:CARRier:POWer? Returns the carrier power.
FETCh:SPURious:COUNt? Returns the number of spurious signals.
FETCh:SPURious:PASS? Returns the pass/fail limit test result.
FETCh:SPURious:SPECtrum:X? Returns the frequencies of the spectrum trace.
FETCh:SPURious:SPECtrum:XY? Returns the frequency and amplitude pairs of the spectrum trace.
FETCh:SPURious:SPECtrum[:Y]? Returns the amplitudes of the spectrum trace.
FETCh:SPURious:SPUR<x>:AMPLitude:ABSolute? Returns the absolute amplitude of the specified spurious signal.
FETCh:SPURious:SPUR<x>:AMPLitude:RELative? Returns the relative amplitude of the specified spurious signal.
FETCh:SPURious:SPUR<x>:FREQuency:ABSolute? Returns the absolute frequency of the specified spurious signal.
FETCh:SPURious:SPUR<x>:FREQuency:RELative? Returns the relative frequency of the specified spurious signal.
FETCh:SPURious:SPUR<x>:LIMit:ABSolute? Returns the absolute amplitude of the limit for a spurious signal.
FETCh:SPURious:SPUR<x>:LIMit:RELative? Returns the relative amplitude of the limit for a spurious signal.
FETCh:SPURious:SPUR<x>:LIMit:VIOLation? Returns whether the specified spurious signal exceeds the limit or
not.
FETCh:SPURious:SPUR<x>:RANGe? Returns the frequency range in which the spurious signal occurred.
FETCh:SQUality subgroup (Option 21 only) Signal quality measurement
FETCh:SQUality:FREQuency:DEViation? Returns the frequency deviation.
FETCh:SQUality:FREQuency:DEViation:TABLe? Returns the frequency deviation measurement results table.
FETCh:SQUality:FREQuency:ERRor? Returns the frequency error.
FETCh:SQUality:GAIN:IMBalance? Returns the gain imbalance.
FETCh:SQUality:ORIGin:OFFSet? Returns the origin offset.
FETCh:SQUality:PEAK:EVM? Returns the peak EVM (%).
FETCh:SQUality:PEAK:EVM:DB? Returns the peak EVM (dB).
FETCh:SQUality:PEAK:EVM:DB:OFFSet? Returns the peak offset EVM (dB).
FETCh:SQUality:PEAK:EVM:LOCation? Returns the time at which the EVM is peak.
FETCh:SQUality:PEAK:EVM:LOCation:OFFSet? Returns the time at which the offset EVM is peak.
FETCh:SQUality:PEAK:EVM:OFFSet? Returns the peak offset EVM (%) in the signal quality measurement.
Table continued…
84
Page 85
Syntax and Commands
Command Description
FETCh:SQUality:PEAK:FERRor? Returns the peak FSK error.
FETCh:SQUality:PEAK:MERRor? Returns the peak magnitude error (%).
FETCh:SQUality:PEAK:MERRor:DB? Returns the peak magnitude error (dB).
FETCh:SQUality:PEAK:MERRor:LOCation? Returns the time at which the magnitude error is peak.
FETCh:SQUality:PEAK:PERRor? Returns the peak phase error.
FETCh:SQUality:PEAK:PERRor:LOCation? Returns the time at which the phase error is peak.
FETCh:SQUality:QUADrature:ERRor? Returns the quadrature error.
FETCh:SQUality:RHO? Returns the r (waveform quality).
FETCh:SQUality:RMS:EVM? Returns the RMS EVM (%).
FETCh:SQUality:RMS:EVM:DB? Returns the RMS EVM (dB).
FETCh:SQUality:RMS:EVM:DB:OFFSet? Returns the RMS offset EVM (dB).
FETCh:SQUality:RMS:EVM:OFFSet? Returns the RMS offset EVM (%).
FETCh:SQUality:RMS:FERRor? Returns the RMS FSK error.
FETCh:SQUality:RMS:MER:DB? Returns the RMS MER (dB).
FETCh:SQUality:RMS:MERRor? Returns the RMS magnitude error (%).
FETCh:SQUality:RMS:MERRor:DB? Returns the RMS magnitude error (dB).
FETCh:SQUality:RMS:PERRor? Returns the RMS phase error.
FETCh:SQUality:SYMBol:LENGth? Returns the number of analyzed symbols.
FETCh:SQUality:SYMBol:RATE? Returns the value of the calculated symbol rate.
FETCh:SQUality:SYMBol:RATE:ERRor? Returns the value of the symbol rate error.
FETCh:TDIagram subgroup (Option 21 only) Trellis diagram
FETCh:TDIagram:FERRor? Returns the frequency error.
FETCh:TDIagram:TRACe? Returns the Trellis diagram trace data.
FETCh:TOVerview subgroup Time overview
FETCh:TOVerview:MEASview<y>? Returns the trace data.
FETCh:WLAN subgroup Wireless LAN measurements
FETCh:WLAN:CONSte:MAGNitude? Returns the magnitude data for the WLAN Constellation
measurement.
FETCh:WLAN:CONSte:PHASe? Returns the phase values for the WLAN Constellation
measurement.
FETCh:WLAN:CONSte:TYPE? Returns the type (context) for the WLAN Constellation
measurement.
FETCh:WLAN:CONSte:VALue? Returns the value (decoded symbol) for the WLAN Constellation
measurement.
FETCh:WLAN:CRESponse:MAGNitude? Returns the magnitude data of the WLAN Channel Response
measurement.
FETCh:WLAN:CRESponse:PHASe? Returns the phase data of the WLAN Channel Response
measurement.
FETCh:WLAN:EVM:TRACe<x>? Returns the trace data for the selected WLAN EVM trace.
Table continued…
SignalVu-PC Vector Analysis Software Programmer Manual 85
Page 86
Syntax and Commands
Command Description
FETCh:WLAN:FLATness:PASS? Verifies the average power level values of the subcarriers remain
within the limits defined for a particular standard.
FETCh:WLAN:FLATness:RESult? Returns the summary results of each segment of the WLAN
Spectral Flatness display.
FETCh:WLAN:FLATness:TRACe<x>? Returns the WLAN Spectral Flatness trace data.
FETCh:WLAN:MERRor:TRACe<x>? Returns the trace data for the selected WLAN Magnitude Error
trace.
FETCh:WLAN:PERRor:TRACe<x>? Returns the trace data for the selected WLAN Phase Error trace.
FETCh:WLAN:PVTime:BURSt:POWer? Returns the average power of the burst packet.
FETCh:WLAN:PVTime:BURSt:WIDTh? Returns the value of the measured time width of the burst packet
from Power-On to Power-Down.
FETCh:WLAN:PVTime:FALL:TIME? Returns the width of the falling edge.
FETCh:WLAN:PVTime:FALL:TIME:STARt? Returns the start time of the falling edge.
FETCh:WLAN:PVTime:FALL:TIME:STOP? Returns the stop time of the falling edge.
FETCh:WLAN:PVTime:FTIMe? Returns the width of the falling edge.
FETCh:WLAN:PVTime:RISE:TIME? Returns the width of the rising edge.
FETCh:WLAN:PVTime:RISE:TIME:STARt? Returns the start time of the rising edge.
FETCh:WLAN:PVTime:RISE:TIME:STOP? Returns the stop time of the rising edge.
FETCh:WLAN:PVTime:RTIMe? Returns the width of the rising edge.
FETCh:WLAN:PVTime:TRACe:X? Returns the horizontal values.
FETCh:WLAN:PVTime:TRACe:XY? Returns the horizontal value (time in seconds) and vertical value
(power).
FETCh:WLAN:PVTime:TRACe[:Y]? Returns the vertical values (power).
FETCh:WLAN:STABle:VALUe? Returns the number of bytes in the symbol table.
FETCh:WLAN:SUMMary:BURSt:INDex? Returns the index of the analyzed packet.
FETCh:WLAN:SUMMary:BURSt:POWer? Returns the average power of all symbols in the packet.
FETCh:WLAN:SUMMary:BURSt:POWer:CFACtor? Returns the peak-to-average burst power factor.
FETCh:WLAN:SUMMary:CERRor? Returns the symbol clock error.
FETCh:WLAN:SUMMary:CPE? Returns the RMS magnitude error of the pilots.
FETCh:WLAN:SUMMary:EVM:PEAK:ALL? Returns the peak EVM value for all subcarriers or all chips.
FETCh:WLAN:SUMMary:EVM:PEAK:CHIP:ALL? Returns the chip at which the reported peak EVM value occurred.
FETCh:WLAN:SUMMary:EVM:PEAK:CHIP: ONEKchips? Returns the chip at which the reported peak EVM value over the
first 1000 chips occurred.
FETCh:WLAN:SUMMary:EVM:PEAK:DATA? Returns the peak EVM value for the data subcarriers.
FETCh:WLAN:SUMMary:EVM:PEAK:ONEKchips? Returns the peak EVM value measured over the first 1000 chips.
FETCh:WLAN:SUMMary:EVM:PEAK:PILots? Returns the peak EVM value for the pilots in the WLAN
measurement.
FETCh:WLAN:SUMMary:EVM:PEAK:SCARrier:ALL? Returns the subcarrier on which the ALL peak EVM value occurred.
Table continued…
86
Page 87
Syntax and Commands
Command Description
FETCh:WLAN:SUMMary:EVM:PEAK:SCARrier:DATA? Returns the subcarrier on which the DATA peak EVM value
occurred.
FETCh:WLAN:SUMMary:EVM:PEAK:SCARrier: PILots? Returns the subcarrier on which the PILOT peak EVM value
occurred.
FETCh:WLAN:SUMMary:EVM:PEAK:SYMBol:ALL? Returns the symbol on which the reported EVM value occurred.
FETCh:WLAN:SUMMary:EVM:PEAK:SYMBol:DATA? Returns the symbol on which the DATA peak EVM value occurred.
FETCh:WLAN:SUMMary:EVM:PEAK:SYMBol:PILots? Returns the symbol on which the PILOT peak EVM value occurred.
FETCh:WLAN:SUMMary:EVM:RMS:ALL? Returns the RMS EVM data for all subcarriers.
FETCh:WLAN:SUMMary:EVM:RMS:AVERage? Returns the average RMS EVM value.
FETCh:WLAN:SUMMary:EVM:RMS:DATA? Returns the RMS EVM data for the data subcarriers.
FETCh:WLAN:SUMMary:EVM:RMS:MAXimum? Returns the maximum RMS EVM value.
FETCh:WLAN:SUMMary:EVM:RMS:ONEKchips? Returns the RMS EVM data for the 1k chips in the WLAN
measurement measured over the first 1000 chips.
FETCh:WLAN:SUMMary:EVM:RMS:PILots? Returns the RMS EVM data for the pilot subcarriers.
FETCh:WLAN:SUMMary:FERRor? Returns the difference between the measured carrier frequency of
the signal and the measurement frequency setting.
FETCh:WLAN:SUMMary:HEADer? Returns the received packet header information.
FETCh:WLAN:SUMMary:HTSig? Returns the decimal values of the received packet HT-SIGNAL
FETCh:WLAN:SUMMary:IQOFfset? Returns the average magnitude of the DC subcarrier level relative to
total signal power.
FETCh:WLAN:SUMMary:LSIG? Returns the decimal values of the received packet (legacy) SIGNAL
symbols fields.
FETCh:WLAN:SUMMary:PACKet? Returns the type and number of symbols in the Preamble and Data
portions of the packet.
FETCh:WLAN:SUMMary:PACKet:DMODulation? Returns the modulation used in the Data symbols.
FETCh:WLAN:SUMMary:PACKet:FORMat? Returns the packet format setting.
FETCh:WLAN:SUMMary:PACKet:GUARd? Returns the packet guard interval used by the DATA symbols.
FETCh:WLAN:SUMMary:SIG? Returns the decimal values of the received packet SIGNAL symbols
fields.
FETCh:WLAN:SUMMary:VHTSig:A? Returns the decimal values of the received packet VHT-SIGNAL(A)
symbols fields.
FETCh:WLAN:SUMMary:VHTSig:B? Returns the decimal values of the received packet VHT-SIGNAL(B)
symbols fields.
FETCh:LTE subgroup
FETCh:LTE:ACLR:MHITs:COUNt? Returns the number of rows in the results table.
FETCh:LTE:ACLR:MHITs<x>:BANDwidth? Returns the bandwidth value of the channel (row).
FETCh:LTE:ACLR:MHITs<x>:CHANnel:NAME? Returns the channel name (row) of the specified index in the results
table.
FETCh:LTE:ACLR:MHITs<x>:FREQuency:OFFSet? Returns the frequency offset of the specified channel (row).
FETCh:LTE:ACLR:MHITs<x>:INTeg:LOWEr: ABSolute? Returns the lower absolute value of the channel (row).
Table continued…
SignalVu-PC Vector Analysis Software Programmer Manual 87
Page 88
Syntax and Commands
Command Description
FETCh:LTE:ACLR:MHITs<x>:INTeg:LOWEr:RELative? Returns the lower relative value of the channel (row).
FETCh:LTE:ACLR:MHITs<x>:INTeg:UPPEr:ABSolute? Returns the upper absolute value of the channel (row).
FETCh:LTE:ACLR:MHITs<x>:INTeg:UPPEr:RELative? Returns the upper relative value of the channel (row).
FETCh:LTE:ACLR:REFerence:POWer? Returns the reference power level.
FETCh:LTE:ACLR:RESUlts:STATus? Returns the pass or fail status.
FETCh:LTE:ACLR:SPECtrum:X? Returns the frequencies of the spectrum trace.
FETCh:LTE:ACLR:SPECtrum:XY? Returns the frequency and amplitude pairs of the spectrum trace.
FETCh:LTE:ACLR:SPECtrum:Y? Returns the amplitude of the spectrum trace.
FETCh:LTE:CHSPectrum:OBW? Returns the Occupied Bandwidth (OBW) in Hz.
FETCh:LTE:CHSPectrum:POWer:CHANnel? Returns the Channel Power value.
FETCh:LTE:CHSPectrum:SPECtrum? Returns spectrum trace data.
FETCh:LTE:CONSte:CELL:ID? Queries the Cell ID value.
FETCh:LTE:CONSte:FREQuency:ERRor? Queries Frequency Error value in Hz.
FETCh:LTE:CONSte:GROUp:ID? Queries the Group ID value.
FETCh:LTE:CONSte:SECTor:ID? Queries the Sector ID value.
FETCh:LTE:PVTime:OFFSlot:POWer? Returns the TOff power measurement value in dBm/MHz.
FETCh:LTE:PVTime:RESUlts:STATus Returns the pass or fail status.
FETCh:LTE:PVTime:TRACe:X? Returns the horizontal values (time in seconds).
FETCh:LTE:PVTime:TRACe:XY? Returns the horizontal value (time in seconds) and vertical value
(power).
FETCh:LTE:PVTime:TRACe:Y? Returns the vertical values (power).
Initiate commands
Use the INITiate commands to control the acquisition of data.
Table 17: Initiate commands
Command Description
INITiate:CONTinuous Sets or queries whether to acquire data continuously.
INITiate[:IMMediate] Starts input signal acquisition.
INITiate:RESume Starts data acquisition.
Input commands
Use the INPut commands to control the characteristics of the signal input. These commands are only available when an RSA306,
RSA306B, RSA500A series,RSA600A series, RSA7100A, MDO4000B series, or an MDO4000C series instrument is connected.
88
Page 89
Syntax and Commands
Table 18: Input commands
Command Description
INPut:CORRection:EXTernal:EDIT<x>:INTerpolation Sets or queries the interpolation setting to use with the indicated
external gain table.
INPut:CORRection:EXTernal:EDIT<x>:NEW Creates the indicated external loss table.
INPut:CORRection:EXTernal:TYPE Sets or queries the data type to use when applying the external loss
table corrections.
INPut:{MLEVel|RLEVel} Sets or queries the reference level.
INPut[:RF]:ATTenuation Sets or queries the input attenuation.
NPut[:RF]:ATTenuation:AUTO Sets or queries whether to set the attenuation automatically.
INPut[:RF]:ATTenuation:MONitor:STATe Sets or queries whether to enable to monitor attenuator use.
INPut[:RF]:GAIN:STATe (Option 50 or 51 only) Sets or queries whether to enable the internal preamplifier.
Table 19: Input commands
Command Description
INPut:CORRection:EXTernal:EDIT<x>:INTerpolation Sets or queries the interpolation setting to use with the indicated
external gain table.
INPut:CORRection:EXTernal:EDIT<x>:NEW Creates the indicated external loss table.
INPut:CORRection:EXTernal:TYPE Sets or queries the data type to use when applying the external loss
table corrections.
INPut:{MLEVel|RLEVel} Sets or queries the reference level.
Mass memory commands
Use the MMEMory commands to manipulate files on the mass memory devices.See the Index for commands not listed in the following
table.
For the trace specifier TRACe<x>, refer to Trace Mnemonics. (See page 2-168.)
If the file extension is not included, it is assumed to be .tiq.
Not all of these commands apply to SignalVu-PC and connected instruments. See the individual command descriptions for details.
Table 20: Mass memory (MMEMory) commands
Command Description
MMEMory:{AM|FM|PM} subgroup AM/FM/PM measurement
MMEMory:{AM|FM|PM}:LOAD:TRACe Loads trace data from the specified file.
MMEMory:TXGain subgroup Transmission Gain measurements
MMEMory:TXGain:LOAD:TRACe<x> Loads the specified saved trace from a file.
MMEMory:TXGain:SHOW:TRACe<x> Displays a saved trace instead of a live trace.
MMEMory:TXGain:STORe:TRACe<x> Saves the selected trace to a file for later recall and analysis.
MMEMory:Noise subgroup Noise Figure and Gain measurements
MMEMory:NOISe:GAIN:LOAD:TRACe Loads the Noise Gain trace data from the specified file.
Table continued…
SignalVu-PC Vector Analysis Software Programmer Manual 89
Page 90
Syntax and Commands
Command Description
MMEMory:NOISe:GAIN:SHOW:TRACe Show or hide the Noise Gain trace from the specified file.
MMEMory:NOISe:GAIN:STORe:TRACe Stores the Noise Gain trace data in the specified file.
MMEMory:Noise:LOAD:ENRCALibration Loads the specified Noise Figure ENR table.
MMEMory:Noise:LOAD:FREQTABle Loads the specified Noise Figure Frequency table.
MMEMory:Noise:STORe:ENRCALibration Saves the Noise Figure ENR table to the specified location.
MMEMory:Noise:STORe:FREQTABle Saves the Noise Figure Frequency table to the specified location.
MMEMory:{AM|FM|PM}:SHOW:TRACe<x> Enables display of a recalled trace file.
MMEMory:{AM|FM|PM}:STORe:TRACe Stores trace data in the specified file.
MMEMory:AUDio subgroup Audio measurements
MMEMory:AUDio:LOAD:FILTer Loads a user-defined audio filter from the specified file.
MMEMory:AVTime subgroup Amplitude versus Time measurement
MMEMory:AVTime [:MEASview<y>]:LOAD:TRACe<x> Loads trace data from the specified file.
MMEMory:AVTime [:MEASview<y>]:SHOW:TRACe<x> Enables display of a recalled trace file.
MMEMory:AVTime [:MEASview<y>]:STORe:TRACe<x> Stores trace data in the specified file.
MMEMory:CALibration subgroup Measurement calibration
MMEMory:CALibration:LOAD:CORRection: EXTernal:EDIT<x> Loads the external loss table data from a specified file.
MMEMory:CALibration:STORe:CORRection: EXTernal:EDIT<x> Stores an external loss table to a specified file.
MMEMory:CCDF subgroup CCDF measurement
MMEMory:CCDF:LOAD:TRACe<x> Loads trace data from the specified file.
MMEMory:CCDF:SHOW:TRACe<x> Enables display of a recalled trace file.
MMEMory:CCDF:STORe:TRACe<x> Stores trace data in the specified file.
MMEMory:DDEMod subgroup DPX spectrum measurement
MMEMory:DDEMod:LOAD:FILTer: MEASurement:USER<x> Loads a user-defined measurement filter from the specified file.
MMEMory:DDEMod:LOAD:FILTer: MEASurement:UOTHer Loads a user-defined measurement filter from the specified file.
MMEMory:DDEMod:LOAD:FILTer:REFerence: USER<x> Loads the specified user-defined reference filter.
MMEMory:DDEMod:LOAD:FILTer:REFerence: UOTHer Loads the specified user-defined reference filter
MMEMory:DDEMod:LOAD:SYMBol:MAP Loads the specified symbol map filename.
MMEMory:DPX subgroup DPX spectrum measurement
MMEMory:DPX:TDM:FREQuency:TXBer: LOAD:PATTern Loads the Tx BER User data pattern from the specified file.
MMEMory:DPX:LOAD:TRACe<x> Loads trace data from the specified file.
MMEMory:DPX:SHOW:TRACe<x> Enables display of a recalled trace file.
MMEMory:DPX:STORe:TRACe<x> Stores trace data in the specified file.
MMEMory:{FSETtling|PSETtling} subgroup Frequency and Phase Settling time measurements
[MMEMory:{FSETtling|PSETtling}:LOAD:TRACe<x> Loads the Frequency or Phase Settling Time trace data from the
specified file.
[MMEMory:{FSETtling|PSETtling}:SHOW:TRACe<x> Enables display of a recalled Frequency or Phase Settling trace file
in Trace<x>.
Table continued…
90
Page 91
Syntax and Commands
Command Description
[MMEMory:{FSETtling|PSETtling}:STORe:TRACe<x> Stores the Frequency or Phase Settling trace data in the specified
file.
MMEMory:FVTime subgroup Frequency versus Time measurement
MMEMory:FVTime[:MEASview<y>]:LOAD:TRACe Loads trace data from the specified file.
MMEMory:FVTime[:MEASview<y>[:SHOW:TRACe<x> Enables display of a recalled trace file.
MMEMory:FVTime[:MEASview<y>]:STORe:TRACe Stores trace data in the specified file.
MMEMory:IQVTime subgroup RF I&Q versus Time measurement
MMEMory:IQVTime[:MEASview<y>]:LOAD:TRACe:I Loads I trace data from the specified file.
MMEMory:IQVTime[:MEASview<y>]:LOAD:TRACe:Q Loads Q trace data from the specified file.
MMEMory:IQVTime[:MEASview<y>]:SHOW:TRACe:I Loads trace data from the specified file.
MMEMory:IQVTime[:MEASview<y>]:SHOW:TRACe<x>:Q Enables display of a recalled trace file.
MMEMory:IQVTime[:MEASview<y>]:STORe:TRACe:I Stores I trace data in the specified file.
MMEMory:IQVTime[:MEASview<y>]:STORe:TRACe:Q Stores Q trace data in the specified file.
MMEMory:LTE subgroup
MMEMory:LTE:ACLR:LOAD:TABLe Loads the LTE ACLR table containing the limits for enabled ranges
from the specified .cvs file.
MMEMory:LTE:ACLR:STORe:TABLe Stores the LTE ACLR table containing the limits for enabled ranges
in a specified .cvs file, allowing you to export the file into Microsoft
Excel or other database system.
MMEMory:LOAD subgroup Load commands
MMEMory:LOAD:IQ Loads time-domain IQ waveform from a specified file.
MMEMory:LOAD:STATe Loads the instrument setup from a specified file.
MMEMory:LOAD:TRACe Loads the trace data from a specified file.
MMEMory:OFDM CONSTe subgroup OFDM Constellation commands
MMEMory:OFDM:CONSte:LOAD:TRACe Loads trace data from the specified file.
MMEMory:OFDM:CONSTe:SHOW:TRACe Enables the display of a recalled trace file.
MMEMory:OFDM:CONSte:STORe:TRACe Stores trace data in the specified file.
MMEMory:PHVTime subgroup Phase versus Time measurement
MMEMory:PHVTime[:MEASview<y>]:LOAD:TRACe Loads trace data from the specified file.
MMEMory:PHVTime[:MEASview<y>]:SHOW:TRACe Enables display of a recalled trace file.
MMEMory:PHVTime[:MEASview<y>]:STORe:TRACe Stores trace data in the specified file.
MMEMory:PNOise subgroup Phase noise measurement
MMEMory:PNOise:LOAD:TRACe<x> Loads the Phase Noise trace data from the specified file.
MMEMory:PNOise:SHOW:TRACe<x> Enables display of a recalled Phase Noise trace file.
MMEMory:PNOise:STORe:TRACe<x> Stores the Phase Noise trace data in the specified file.
MMEMory:SEM subgroup Spectral Emissions Mask measurement
MMEMory:SEM:LOAD:TABLe Loads the SEM table from the specified file.
MMEMory:SEM:STORe:TABLe Stores the SEM table in the specified file.
Table continued…
SignalVu-PC Vector Analysis Software Programmer Manual 91
Page 92
Syntax and Commands
Command Description
MMEMory:SGRam subgroup Spurious measurement
MMEMory:SGRam [:MEASview<y>]:LOAD:TRACe Loads the trace data from a specified file.
MMEMory:SGRam [:MEASview<y>]:SHOW:TRACe Enables display of a recalled trace file.
MMEMory:SGRam [:MEASview<y>]:STORe:TRACe Stores the Spectrogram trace data in the specified file.
MMEMory:SPECtrum subgroup Spectrum measurement
MMEMory:SPECtrum [:MEASview<y>]:LOAD:TRACe Loads the trace data from a specified file.
MMEMory:SPECtrum [:MEASview<y>]:SHOW:TRACe<x> Enables display of a recalled trace file.
MMEMory:SPECtrum [:MEASview<y>]:STORe:TRACe<x> Stores the spectrum trace data in the specified file.
MMEMory:SPURious subgroup Spurious measurement
MMEMory:SPURious:LOAD:TABLe Loads the spurious table from the specified file.
MMEMory:SPURious:STORe:TABLe Stores the spurious table in the specified file.
MMEMory:STORe subgroup Store commands
MMEMory:STORe:IQ Saves time-domain IQ waveform in the acquisition memory to a
specified file.
MMEMory:STORe:IQ:CSV Saves time-domain IQ waveform in the acquisition memory to a
specified file in the CSV (Comma Separated Values) format.
MMEMory:STORe:IQ:MAT Saves time-domain IQ waveform in the acquisition memory to a
specified file in the MATLAB format.
MMEMory:STORe:IQ:SELEct:DATA Sets or queries the type of data stored in an acquisition data file.
MMEMory:STORe:IQ:SELEct:FRAMes Sets or queries which frames to save when saving TIQ acquisition
data files.
MMEMory:STORe:IQ:SELEct:LENGth Sets or queries what portion of each record is saved when saving
acquisition data.
MMEMory:STORe:MSTate Stores the measurement parameters in a specified file.
MMEMory:STORe:RESults Stores the measurement results including measurement parameters
and trace data to a specified file.
MMEMory:STORe:SCReen Stores the measurement results in a specified file.
MMEMory:STORe:STATe Stores the instrument setup in a specified file.
MMEMory:STORe:TRACe Stores trace data in a specified file.
MMEMory:TOVerview subgroup Spurious measurement
MMEMory:TOVerview [:MEASview<y>]:LOAD:TRACe1 Loads the trace data from a specified file.
MMEMory:TOVerview [:MEASview<y>]:SHOW:TRACe1 Enables display of a recalled trace file.
MMEMory:TOVerview [:MEASview<y>]:STORe:TRACe1 Stores the selected trace data into the specified file.
MMEMory:WLAN subbroup Wireless LAN measurements
MMEMory:WLAN:CRESponse:LOAD: TRACe<x> Loads the selected WLAN Channel Response trace data from the
specified file.
MMEMory:WLAN:CRESponse:SHOW: TRACe<x> Enables the display of a recalled WLAN Channel Response trace.
MMEMory:WLAN:CRESponse:STORe: TRACe<x> Stores the WLAN Channel Response measurement trace data in
the specified file.
92
Page 93
Syntax and Commands
Table 21: Mass memory (MMEMory) commands
Command Description
MMEMory:{AM|FM|PM} subgroup AM/FM/PM measurement
MMEMory:{AM|FM|PM}:LOAD:TRACe Loads trace data from the specified file.
MMEMory:MAPIt subgroup MapIt feature
MMEMory:MAPit:LOAD Loads the MapIt measurement results from the specified file.
MMEMory:MAPit:STORe Save the selected MapIt measurement results to a file.
MMEMory:MAPit:STORe:ALL Saves all of the MapIt measurement results from memory to the
specified file.
MMEMory:Noise subgroup Noise Figure and Gain measurements
MMEMory:NOISe:GAIN:LOAD:TRACe Loads the Noise Gain trace data from the specified file.
MMEMory:NOISe:GAIN:SHOW:TRACe Show or hide the Noise Gain trace from the specified file.
MMEMory:NOISe:GAIN:STORe:TRACe Stores the Noise Gain trace data in the specified file.
MMEMory:Noise:LOAD:ENRCALibration Loads the specified Noise Figure ENR table.
MMEMory:Noise:LOAD:FREQTABle Loads the specified Noise Figure Frequency table.
MMEMory:Noise:STORe:ENRCALibration Saves the Noise Figure ENR table to the specified location.
MMEMory:Noise:STORe:FREQTABle Saves the Noise Figure Frequency table to the specified location.
MMEMory:{AM|FM|PM}:SHOW:TRACe<x> Enables display of a recalled trace file.
MMEMory:{AM|FM|PM}:STORe:TRACe Stores trace data in the specified file.
MMEMory:AUDio subgroup Audio measurements
MMEMory:AUDio:LOAD:FILTer Loads a user-defined audio filter from the specified file.
MMEMory:AVTime subgroup Amplitude versus Time measurement
MMEMory:AVTime [:MEASview<y>]:LOAD:TRACe<x> Loads trace data from the specified file.
MMEMory:AVTime [:MEASview<y>]:SHOW:TRACe<x> Enables display of a recalled trace file.
MMEMory:AVTime [:MEASview<y>]:STORe:TRACe<x> Stores trace data in the specified file.
MMEMory:CALibration subgroup
Measurement calibration
(Requires an RSA306, RSA306B, RSA500A series, RSA600A
series, MDO4000B series, or MDO4000C series instrument be
connected.)
MMEMory:CALibration:LOAD:CORRection: EXTernal:EDIT<x> Loads the external loss table data from a specified file.
MMEMory:CALibration:STORe:CORRection: EXTernal:EDIT<x> Stores an external loss table to a specified file.
MMEMory:DDEMod subgroup DPX spectrum measurement
MMEMory:DDEMod:LOAD:FILTer: MEASurement:USER<x> Loads a user-defined measurement filter from the specified file.
MMEMory:DDEMod:LOAD:FILTer: MEASurement:UOTHer Loads a user-defined measurement filter from the specified file.
MMEMory:DDEMod:LOAD:FILTer:REFerence: USER<x> Loads the specified user-defined reference filter.
MMEMory:DDEMod:LOAD:FILTer:REFerence: UOTHer Loads the specified user-defined reference filter
MMEMory:DDEMod:LOAD:SYMBol:MAP Loads the specified symbol map filename.
MMEMory:DPX subgroup DPX spectrum measurement
Table continued…
SignalVu-PC Vector Analysis Software Programmer Manual 93
Page 94
Syntax and Commands
Command Description
MMEMory:DPX:TDM:FREQuency:TXBer: LOAD:PATTern Loads the Tx BER User data pattern from the specified file.
MMEMory:DPX:LOAD:TRACe<x> Loads trace data from the specified file.
MMEMory:DPX:SHOW:TRACe<x> Enables display of a recalled trace file.
MMEMory:DPX:STORe:TRACe<x> Stores trace data in the specified file.
MMEMory:{FSETtling|PSETtling} subgroup Frequency and Phase Settling time measurements
[MMEMory:{FSETtling|PSETtling}:LOAD:TRACe<x> Loads the Frequency or Phase Settling Time trace data from the
specified file.
[MMEMory:{FSETtling|PSETtling}:SHOW:
TRACe<x>
[MMEMory:{FSETtling|PSETtling}:STORe:TRACe<x> Stores the Frequency or Phase Settling trace data in the specified
MMEMory:FVTime subgroup Frequency versus Time measurement
MMEMory:FVTime [:MEASview<y>]:LOAD:TRACe Loads trace data from the specified file.
MMEMory:FVTime [:MEASview<y>]:SHOW:TRACe<x> Enables display of a recalled trace file.
MMEMory:FVTime [:MEASview<y>]:STORe:TRACe Stores trace data in the specified file.
MMEMory:IQVTime subgroup RF I&Q versus Time measurement
MMEMory:IQVTime [:MEASview<y>]:LOAD:TRACe:I Loads I trace data from the specified file.
MMEMory:IQVTime [:MEASview<y>]:LOAD:TRACe:Q Loads Q trace data from the specified file.
MMEMory:IQVTime [:MEASview<y>]:SHOW:TRACe:I Loads trace data from the specified file.
MMEMory:IQVTime [:MEASview<y>]:SHOW:TRACe<x>:Q Enables display of a recalled trace file.
MMEMory:IQVTime [:MEASview<y>]:STORe:TRACe:I Stores I trace data in the specified file.
MMEMory:IQVTime [:MEASview<y>]:STORe:TRACe:Q Stores Q trace data in the specified file.
MMEMory:LTE subgroup
MMEMory:LTE:ACLR:LOAD:TABLe Loads the LTE ACLR table containing the limits for enabled ranges
MMEMory:LTE:ACLR:STORe:TABLe Stores the LTE ACLR table containing the limits for enabled ranges
MMEMory:LOAD subgroup Load commands
MMEMory:LOAD:IQ Loads time-domain IQ waveform from a specified file.
MMEMory:LOAD:STATe Loads the instrument setup from a specified file.
MMEMory:LOAD:TRACe Loads the trace data from a specified file.
MMEMory:OFDM CONSTe subgroup OFDM Constellation commands
MMEMory:OFDM:CONSte:LOAD:TRACe Loads trace data from the specified file.
MMEMory:OFDM:CONSTe:SHOW:TRACe Enables the display of a recalled trace file.
MMEMory:OFDM:CONSte:STORe:TRACe Stores trace data in the specified file.
MMEMory:PHVTime subgroup Phase versus Time measurement
MMEMory:PHVTime [:MEASview<y>]:LOAD:TRACe Loads trace data from the specified file.
Table continued…
Enables display of a recalled Frequency or Phase Settling trace file
in Trace<x>.
file.
from the specified .cvs file.
in a specified .cvs file, allowing you to export the file into Microsoft
Excel or other database system.
94
Page 95
Syntax and Commands
Command Description
MMEMory:PHVTime [:MEASview<y>]:SHOW:TRACe Enables display of a recalled trace file.
MMEMory:PHVTime [:MEASview<y>]:STORe:TRACe Stores trace data in the specified file.
MMEMory:PNOise subgroup Phase noise measurement
MMEMory:PNOise:LOAD:TRACe<x> Loads the Phase Noise trace data from the specified file.
MMEMory:PNOise:SHOW:TRACe<x> Enables display of a recalled Phase Noise trace file.
MMEMory:PNOise:STORe:TRACe<x> Stores the Phase Noise trace data in the specified file.
MMEMory:SEM subgroup Spectral Emissions Mask measurement
MMEMory:SEM:LOAD:TABLe Loads the SEM table from the specified file.
MMEMory:SEM:STORe:TABLe Stores the SEM table in the specified file.
MMEMory:SGRam subgroup Spurious measurement
MMEMory:SGRam [:MEASview<y>]:LOAD:TRACe Loads the trace data from a specified file.
MMEMory:SGRam [:MEASview<y>]:SHOW:TRACe Enables display of a recalled trace file.
MMEMory:SGRam [:MEASview<y>]:STORe:TRACe Stores the Spectrogram trace data in the specified file.
MMEMory:SPECtrum subgroup Spectrum measurement
MMEMory:SPECtrum [:MEASview<y>]:LOAD:TRACe Loads the trace data from a specified file.
MMEMory:SPECtrum [:MEASview<y>]:SHOW:TRACe<x> Enables display of a recalled trace file.
MMEMory:SPECtrum [:MEASview<y>]:STORe:TRACe<x> Stores the spectrum trace data in the specified file.
MMEMory:SPURious subgroup Spurious measurement
MMEMory:SPURious:LOAD:TABLe Loads the spurious table from the specified file.
MMEMory:SPURious:STORe:TABLe Stores the spurious table in the specified file.
MMEMory:STORe subgroup Store commands
MMEMory:STORe:IQ Saves time-domain IQ waveform in the acquisition memory to a
specified file.
MMEMory:STORe:IQ:CSV Saves time-domain IQ waveform in the acquisition memory to a
specified file in the CSV (Comma Separated Values) format.
MMEMory:STORe:IQ:MAT Saves time-domain IQ waveform in the acquisition memory to a
specified file in the MATLAB format.
MMEMory:STORe:IQ:SELEct:DATA Sets or queries the type of data stored in an acquisition data file.
MMEMory:STORe:IQ:SELEct:FRAMes Sets or queries which frames to save when saving TIQ acquisition
data files.
MMEMory:STORe:IQ:SELEct:LENGth Sets or queries what portion of each record is saved when saving
acquisition data.
MMEMory:STORe:MSTate Stores the measurement parameters in a specified file.
MMEMory:STORe:RESults Stores the measurement results including measurement parameters
and trace data to a specified file.
MMEMory:STORe:SCReen Stores the measurement results in a specified file.
MMEMory:STORe:STATe Stores the instrument setup in a specified file.
MMEMory:STORe:TRACe Stores trace data in a specified file.
MMEMory:TOVerview subgroup Spurious measurement
Table continued…
SignalVu-PC Vector Analysis Software Programmer Manual 95
Page 96
Syntax and Commands
Command Description
MMEMory:TOVerview [:MEASview<y>]:LOAD:TRACe1 Loads the trace data from a specified file.
MMEMory:TOVerview [:MEASview<y>]:SHOW:TRACe1 Enables display of a recalled trace file.
MMEMory:TOVerview [:MEASview<y>]:STORe:TRACe1 Stores the selected trace data into the specified file.
MMEMory:WLAN subbroup Wireless LAN measurements
MMEMory:WLAN:CRESponse:LOAD: TRACe<x> Loads the selected WLAN Channel Response trace data from the
specified file.
MMEMory:WLAN:CRESponse:SHOW: TRACe<x> Enables the display of a recalled WLAN Channel Response trace.
MMEMory:WLAN:CRESponse:STORe: TRACe<x> Stores the WLAN Channel Response measurement trace data in
the specified file.
Specifying the File
For loading and storing a file, specify the file following these rules
• You can omit the file extension to load and store data. The measurement-specific extension is automatically added.
• You can use the absolute path to specify the file name. For example,specify the SAMPLE1 file in the My Documents folder on the C
drive as "C:\My Documents\SAMPLE1".
• C:\Program Files\Tektronix\SignalVu-PC initially.
Once a file is saved to a different directory, the new directory will be used as the default for all load and store operations.
Output commands
Use the OUTPut commands to control the characteristics of the signal output. See the Index for commands not listed in the following table.
Not all commands apply to all products. See the command descriptions for details.
Table 22: Output commands
Command Description
OUTPut:IF:{BANDwidth|BWIDth} (Option 05 only) Sets or queries the IF output filter.
OUTPut:IF[:STATe] (Option 05 only) Sets or queries whether to turn on or off IF
output.
OUTPut:IQ:SOURce (Option 05 only) Sets or queries the IQ data transfer via the
LVDS card.
OUTPut:IQ[:STATe] (Option 05 only) Sets or queries whether to turn on or off IQ
output.
OUTPut:NOISe[:STATe] Sets or queries whether to turn on or off 28
V DC power.
OUTPut:ZS:{BANDwidth|BWIDth} Sets or queries the resolution bandwidth
RBW filter.
OUTPut:ZS:{BANDwidth|BWIDth}:AUTO Sets or queries whether the resolution
bandwidth will be set manually or
automatically.
OUTPut:ZS:{BANDwidth|BWIDth}: STATe Sets or queries the state of the resolution
bandwidth filter.
Table continued…
96
Page 97
Syntax and Commands
Command Description
OUTPut:ZS[:STATe] Enable or disable the Zero Span output.
OUTPut:ZS:DELay? Queries the delay from the input connector
to the Zero Span output.
OUTPut:ZS:FILTer:STATe Sets or queries the signal path of the filter to
the Zero Span output.
OUTPut:ZS:VOLTage Sets or queries the voltage level at the Zero
Span output.
OUTPut:ZS:VOLTage:AUTO Sets or queries or queries how the output
voltage is referenced.
OUTPut:TGen:BRIDge:MODE (Option 04 only; available for the RSA500A/
600A series only))
OUTPut:TGen:ENABle (Option 04 only; available for the RSA500A/
600A series only))
OUTPut:TGen:FREQuency (Option 04 only; available for the RSA500A/
600A series only))
OUTPut:TGen:INSTalled? (Option 04 only; available for the RSA500A/
600A series only))
OUTPut:TGen:LEVel (Option 04 only; available for the RSA500A/
600A series only))
OUTPut:IF:{BANDwidth|BWIDth} (Option 05 only) Sets or queries the IF output filter.
OUTPut:IF[:STATe] (Option 05 only) Sets or queries whether to turn on or off IF
OUTPut:IQ:SOURce (Option 05 only) Sets or queries the IQ data transfer via the
OUTPut:IQ[:STATe] (Option 05 only) Sets or queries whether to turn on or off IQ
OUTPut:NOISe[:STATe] Sets or queries whether to turn on or off 28
OUTPut:ZS:{BANDwidth|BWIDth} Sets or queries the resolution bandwidth
OUTPut:ZS:{BANDwidth|BWIDth}:AUTO Sets or queries whether the resolution
OUTPut:ZS:{BANDwidth|BWIDth}: STATe Sets or queries the state of the resolution
OUTPut:ZS[:STATe] Enable or disable the Zero Span output.
OUTPut:ZS:DELay? Queries the delay from the input connector
OUTPut:ZS:FILTer:STATe Sets or queries the signal path of the filter to
OUTPut:ZS:VOLTage Sets or queries the voltage level at the Zero
Table continued…
Sets or queries the tracking generator bridge
mode.
Sets or queries the power state of the
tracking generator.
Sets or queries the tracking generator
frequency in Hz.
Queries for the presence of the tracking
generator hardware.
Sets or queries the tracking generator output
level in dBm.
output.
LVDS card.
output.
V DC power.
RBW filter.
bandwidth will be set manually or
automatically.
bandwidth filter.
to the Zero Span output.
the Zero Span output.
Span output.
SignalVu-PC Vector Analysis Software Programmer Manual 97
Page 98
Syntax and Commands
Command Description
OUTPut:ZS:VOLTage:AUTO Sets or queries or queries how the output
voltage is referenced.
OUTPut:TGen:BRIDge:MODE (Option 04 only; available for the RSA500A/
600A series only))
OUTPut:TGen:ENABle (Option 04 only; available for the RSA500A/
600A series only))
OUTPut:TGen:FREQuency (Option 04 only; available for the RSA500A/
600A series only))
OUTPut:TGen:INSTalled? (Option 04 only; available for the RSA500A/
600A series only))
OUTPut:TGen:LEVel (Option 04 only; available for the RSA500A/
600A series only))
Sets or queries the tracking generator bridge
mode.
Sets or queries the power state of the
tracking generator.
Sets or queries the tracking generator
frequency in Hz.
Queries for the presence of the tracking
generator hardware.
Sets or queries the tracking generator output
level in dBm.
Read commands
The READ commands acquire an input signal once in the single mode and obtain the measurement results from that data. See the Index
for commands not listed in the following table.
To fetch the measurement results from the data currently residing in the memory without acquiring the input signal, use the FETCh
commands.
Not all commands apply to all products. See the command descriptions for details.
Table 23: Read commands
Command Description
READ:ACPower subgroup Channel power and ACPR measurement
READ:ACPower? Returns the ACPR measurement results.
READ:PULSe subgroup Pulse measurements
READ:PULSe:CUMulative:HISTogram[:MEASview<y>]:OUTLier:
HIGHer?
READ:PULSe:CUMulative:HISTogram[:MEASview<y>]:OUTLier:
LOWer?
READ:PULSe:CUMulative:HISTogram[:MEASview<y>]:PULse:COU
Nt?
READ:PULSe:CUMulative:HISTogram[:MEASview<y>]:PULse:TOT
al?
READ:PULSe:CUMulative:STATistics[:MEASview<y>] Returns the PulseCount, Max, Max TimeStamp, Min, Min
READ:PULSe[:RESult][:MEASview<y>]:ADVanced Returns the Pulse Count, Max, Max at Pulse number, Min, Min
READ:PULSe[:RESult][:MEASview<y>]:FABS? Returns the computed absolute frequency from the carrier in the
Table continued…
Returns the outliers value exceeding the upper limit.
Returns the outliers value below the lower limit.
Returns the number of pulses in the bin.
Returns the total number of pulses.
TimeStamp, Peak to Peak, Average and Standard Deviation values
for the chosen measurement.
at Pulse number, Peak to Peak, Average and Standard Deviation
values for the chosen measurement in pulse table.
pulse table.
98
Page 99
Syntax and Commands
Command Description
READ:PULSe[:RESult][:MEASview<y>]:PPFD? Returns the computed pulse to pulse frequency difference from the
carrier in the pulse table.
READ:PULSe[:RESult][:MEASview<y>]:PPPD? Returns the computed pulse to pulse phase difference from the
carrier in the pulse table.
READ:PULSe:STATistics[:MEASview<y>]:ADVanced Returns the Pulse Count, Max, Max at Pulse number, Min, Min
at Pulse number, Peak to Peak, Average and Standard Deviation
values for the chosen measurement in pulse statistics.
READ:PULSe:STATistics[:MEASview<y>]:FABS Returns the absolute frequency in pulse statistics.
READ:PULSe:STATistics[:MEASview<y>]:MAX:PULSe:NUMber Returns the maximum value at a certain pulse number in pulse
statistics.
READ:PULSe:STATistics[:MEASview<y>]:MIN:PULSe:NUMber? Returns the minimum value at a certain pulse number in pulse
statistics.
READ:PULSe:STATistics[:MEASview<y>]:PPFD Returns the pulse-pulse frequency difference in pulse statistics.
READ:PULSe:STATistics[:MEASview<y>]:PPPD Returns the pulse-pulse phase difference in pulse statistics.
READ:Bluetooth subgroup Bluetooth measurements
READ:BIBEmissions:FTX? Returns the band number corresponding to the transmitted FTX
detected in the display.
READ:BIBEmissions:POWer? Returns all channel power results.
READ:BIBEmissions:RESUlts:STATus? Returns the Pass/Fail result status.
READ:BLUEtooth:CONSte:FERRor? Queries the frequency error.
READ:BLUEtooth:CONSte:TRACe? Returns the trace data for the display.
READ:BLUEtooth:EDIagram:FDEViation? Returns the frequency deviation vs. time trace data with the X
values.
READ:BLUEtooth:EDIagram:FERRor? Returns the frequency error.
READ:BLUEtooth:EDIagram:HORiz:SCALe? Returns the value of the horizontal scale.
READ:BLUEtooth:EDIagram:I? Returns the I vs. time trace.
READ:BLUEtooth:EDIagram:Q? Returns the Q vs. time trace.
READ:BLUEtooth:FDVTime:TRACe? Returns the trace data or the display.
READ:BLUEtooth:FREQuency:ERROr? Returns the frequency error.
READ:BLUEtooth:FREQuency:ERROr:TYPE Returns the frequency error type.
READ:BLUEtooth:FREQuency:OFFSet:DRIFt: F1FZero? Returns the drift in frequency offset (f1–f0 — the frequency offset
calculated in the first interval in the payload — the frequency offset
calculated in the preamble).
READ:BLUEtooth:FREQuency:OFFSet:DRIFt: FNFN5? Returns the maximum drift of the frequency offset in payload
intervals spaced 50 μs away.
READ:BLUEtooth:FREQuency:OFFSet:DRIFt:FNFN5: INTErval? Returns the interval at which the maximum drift of frequency offset
in a duration of 50 μs occurred.
READ:BLUEtooth:FREQuency:OFFSet:DRIFt: FNFZERO? Returns the maximum drift of the frequency offset of the intervals in
the payload from the preamble packet in the Bluetooth Frequency
Deviation vs. Time display.
Table continued…
SignalVu-PC Vector Analysis Software Programmer Manual 99
Page 100
Syntax and Commands
Command Description
READ:BLUEtooth:FREQuency:OFFSet:DRIFt:
FNFZERO:INTErval?
READ:BLUEtooth:FREQuency:OFFSet:MAX? Returns the maximum frequency offset in the Frequency Deviation
READ:BLUEtooth:FREQuency:OFFSet:MAX: INTErval? Returns the maximum frequency offset interval in the Frequency
READ:BLUEtooth:FREQuency:OFFSet:PREAmble? Returns the offset calculated in the preamble region in the
READ:BLUEtooth:MODUlation:CHARacteristics: AVErage:F? Returns the average frequency value when the selected test pattern
READ:BLUEtooth:MODUlation:CHARacteristics:
AVErage:F2F1ratio?
READ:BLUEtooth:MODUlation:CHARacteristics: AVErage:FONE? Returns the average frequency deviation for the low deviation
READ:BLUEtooth:MODUlation:CHARacteristics: AVErage:FTWO? Returns the average frequency deviation for the high deviation
READ:BLUEtooth:SUMMary:FREQuency:OFFSet: DRIFt:COUNt? Returns the number of packets analyzed to obtain average drift
READ:BLUEtooth:SUMMary:FREQuency:OFFSet: DRIFt:F1FZero? Returns the drift f1–f0 value.
READ:BLUEtooth:SUMMary:FREQuency:OFFSet:
DRIFt:F1FZero:STATus?
READ:BLUEtooth:SUMMary:FREQuency:OFFSet: DRIFt:FNFN5? Returns the maximum drift of the fn–fn-5 value.
READ:BLUEtooth:SUMMary:FREQuency:OFFSet:
DRIFt:FNFN5:STATus?
READ:BLUEtooth:SUMMary:FREQuency:OFFSet: DRIFt:FNFZero? Returns the maximum drift fn–f0.
READ:BLUEtooth:SUMMary:FREQuency:OFFSet:
DRIFt:FNFZero:STATus?
READ:BLUEtooth:SUMMary:FREQuency:OFFSet: MAX? Returns the maximum frequency offset present in the packet.
READ:BLUEtooth:SUMMary:FREQuency:OFFSet: MAX:STATus? Returns the Pass/Fail result status of the frequency offset maximum
READ:BLUEtooth:SUMMary:FREQuency:OFFSet: PREAmble? Returns the frequency offset value in the preamble region.
READ:BLUEtooth:SUMMary:FREQuency:OFFSet:
PREAmble:STATus?
READ:BLUEtooth:SUMMary:MODUlation:CHARacteristics:AVErage
:DELTa:F:MAX:PERCentage:COUNt?
READ:BLUEtooth:SUMMary:MODUlation:CHARacteristics:AVErage
: DELTa:FONE:MAX:PERCentage:COUNt?
READ:BLUEtooth:SUMMary:MODUlation:CHARacteristics:AVErage
: DELTa:FTWO:MAX:PERCentage?
Table continued…
Returns the interval (n) at which the maximum drift fn-f0 occurred in
the Bluetooth Frequency Deviation vs. Time display.
vs. Time and the Center Frequency Offset and Drift displays.
Deviation vs. Time and the Center Frequency Offset and Drift
displays.
Frequency Deviation vs. Time and the Center Frequency Offset
and Drift displays.
is Other in the Bluetooth Frequency Deviation vs. Time display.
Returns the average ratio value for the high and low frequency
deviation in the Bluetooth Frequency Deviation vs. Time display.
pattern in the Bluetooth Frequency Deviation vs. Time display.
pattern.
results.
Returns the Pass/Fail drift f1–f0 result status in the packet.
Returns the Pass/Fail status of the maximum fn–fn-5 drift in the
packet.
Returns the Pass/Fail result status of the fn–f0 maximum drift in the
packet.
in the packet.
Returns the Pass/Fail result status of the frequency offset in the
preamble region.
Returns the number of packets analyzed out of 10 packets for
ΔFavg.
Returns the number of packets analyzed out of 10 packets for the
ΔF1avg.
Returns the percentage of the ΔF2max% values that are above the
specified limit.
100
Loading...