Tektronix Series 3400 Pulse Pattern Generators Quick Start Guide

Quick Start Guide

Step 2

2 Width

Delay
LeadE
TrailE

3.00 ns
0 ps

2.5 ns

2.5 ns

Pulse Mode
CH 1 Ampl

1.00 Vpp

Trigger = ExtIn

1 Width

Delay
LeadE
TrailE

3.04 ns
0 ps

2.5 ns

2.5 ns

Freq 165.0 MHz Per 6.06 ns

Channel Freq Per Width Delay More

Step 3

Step 1

Channel Ampl Offset HiLvl LoLvl More

1 Ampl

Offset
HiLvl
LoLvl
Pol

1.00 Vpp
0m V

500 mV

-500 mV
Norm

2 Ampl

Offset
HiLvl
LoLvl
Pol

1.00 Vpp
0m V

500 mV

-500 mV
Norm

Pulse Mode

Ch 1 Ampl

1.00 Vpp

Trigger = ExtIn

Freq

1 Width

Delay
LeadE
TrailE

1.000 MHz

500.0 ns

250.0 ns

2.5 ns

2.5 ns

Per

2 Width

Delay
LeadE
TrailE

1.000 µs

100.0 ns

250.0 ns

2.5 ns

2.5 ns

Pulse Mode

Ch 1 Width

500.0ns

Trigger = ExtIn

Channel Freq Per Width Delay More

Understanding Basic Pulse Parameters

Setting your pulse parameters is a simple three step
process:

1. Choose your high level configuration with the menu keys.

2. Select the desired parameter with the Soft Keys.

3. Enter the desired value with the control knob or numerical
keypad.

Front Panel Setup Example

The following information demonstrates how to properly connect a
Keithley Instruments Model 340x Pulse Pattern Generator to an

oscilloscope
information depicts how to adjust the most common pulse
parameters, including pulse amplitude, offset, width, period, and
leading and trailing edges.

Power On the Model 340x Pulse Pattern Generator:

1. Enable rear panel power switch (“ON” position).

2. Press front panel on/off switch.

Make Connections Between Pulse Generator &
Oscilloscope:

Connect a BNC-BNC cable between CH 1 output and CH 1 input of
the oscilloscope.

Configure Oscilloscope:

1. In trigger menu of scope:

2. In vertical menu of scope:

3. In Horizontal menu of scope, adjust the time scale to 400ns.

Turn on output Channel 1 of the pulse generator by pressing the CH
1 Enable button and verify that you have the following signal:

1

and how to navigate the front panel menu. The

a. Configure scope to trigger on rising edge of CH 1.
b. Set trigger level to +0.25V.

a. Set input impedance to 50 or use a 50 feed through, such

as the Keithley Instruments Model 7755.

b. Set voltage scale to 500mV/division.

Adjust Output Pulse:

Unit should power up in “Mode” display window.

1. Press “Pulse” soft key.

2. Press VOLTS menu key.

3. Verify Channel 1 is selected. (NOTE: The dark gray area
should appear on left side of display and a “1” should appear in
the top left corner of display.)

4. Set amplitude to 1.50Vpp:
a. Press “Ampl” soft key. If “Ampl” soft key is not visible, first

press the “More” soft key.

b. Use knob to adjust amplitude value to “1.50 Vpp.”

NOTE: Field “HiLvl” should read “750mV” and “LoLvl” should read

“-750mV.”

5. Set offset to 750mV:
a. Press “Offset” soft key.
b. Use numeric keys to enter “0.75.” NOTE: Units appear

above the soft keys.

c. Press soft key that corresponds to “V.”

NOTE: Field “HiLvl” should read “1.5V” and “LoLvl” should read

“0mV.”

6. Press TIME menu key.

7. Change pulse width to 500ns:
a. Press “Width” soft key.
b. Use knob to scroll to 500ns.

9. Change period to 2µs:
a. Press “More” soft key.
b. Press “Per” soft key.
c. Use knob to change the period to 2µs.

Oscilloscope should now display the following waveform:

Other Notes:

- These steps can be repeated using CH 2. Use the “Channel”
soft key in TIME and VOLTS menus to select CH 2 and adjust
its parameters. To enable CH 2 output, press the CH 2 Enable
key.

- The TRIG OUT terminal of the Model 340x may be used to
trigger the scope. The Trig Out signal is a TTL signal at 50%
duty cycle this has the same pulse repetition frequency as the
output channel(s). Please refer to section 5 of the User’s
manual for details on triggering.

Reset Model 340x to Factory Defaults:

1. Press UTILITY menu key.

2. Press “Recall” soft key

3. Press “Default” soft key. (Instrument will now reset to factory
defaults.)

For additional help, please review the Model 340x User’s Manual.
You may also view FAQs or submit a request for a consult with an
Applications Engineer on the Keithley Instruments website at
www.keithley.com.

8. Adjust leading and trailing edges:
a. Press “More” soft key.
b. Press “LeadE” soft key.
c. Use numeric keys to enter “100.”
d. Press “ns” soft key.
e. Press “TrailE” soft key.
f. Use numeric keys to enter “250” then press the “ns” soft

key.

1. In order to observe the fastest rise times of the Model 340x Pulse Pattern
Generator, an oscilloscope with 500MHz bandwidth is recommended.

Keithley Instruments 3402 Front panel

On/Off

Switch

1

2

LCD Display

Channel 1

Parameters

2a

Selected

Parameter

2c

Channel 2

Parameters

2b

5

Rotory Knob

Cursor Keys

7

6

Numeric Keypad

3

Menu

Keys

Clock, Trigger and

Strobe Connectors

(BNC)

10

8

Output Enable

Pulse/Pattern

Output

Connectors

(BNC)

9

Soft Keys

4

Soft Key

Options

For the Model 340x-R Rear Panel

Output option, item 10 connectors

are moved to the rear panel.

2 Width

Delay

LeadE

TrailE

3.00 ns

0 ps

2.5 ns

2.5 ns

Pulse Mode

Ch 1 Width

3.04 ns

Trigger = PLL

1 Width

Delay

LeadE

TrailE

3.04 ns

0 ps

2.5 ns

2.5 ns

Freq 165.0 MHz Per 6.06 ns

Channel Freq Per Width Delay More

Ampl

(Amplitude)

1Vpp

Width

+500mV

-500mV

Per

(Period)

LeadE

(Leading Edge)

Trigger

Delay

0V

HiLvl

(High

Level)

LoLvl

(Low Level)

Offset

(Median)

Freq

(Frequency)

LeadE

(Leading Edge)

TrailE

(Trailing Edge)

Time Parameters

Not Drawn To Scale

NOTE: Front panel controls and connectors for the Keithley 3401

single-channel pulse/pattern generator are similar except
there is only one channel.

Pulse Parameters Example

Series 3400 Pulse Pattern Generator

Quick Start Guide

3400S-903-01 Rev B. / January 2007

A GREATER MEASURE OF CONFIDENCE