Tektronix RSA6106A, RSA6114A, RSA6120A, RSA5103A, RSA5106A Primary User
x
RSA6100A Series Real-Time Spectrum Analyzers
RSA5100A Series Real-Time Signal Analyzers
ZZZ
Quick Start User Manual
*P071283800*
071-2838-00
xx
RSA6100A Series Real-Time Spectrum Analyzers
RSA5100A Series Real-Time Signal Analyzers
ZZZ
Quick Start User Manual
www.tektronix.com
071-2838-00
Copyright © Tektronix. All rights reserved. Licensed software products are owned by Tektronix or its subsidiaries or suppliers, and are
protected by na
tional copyright laws and international treaty provisions.
Tektronix pro
previously published material. Specifications and price change privileges reserved.
TEKTRONIX and TEK are registered trademarks of Tektronix, Inc.
ducts are covered by U.S. and foreign patents, issued and pending. Information in this publication supersedes that in all
Contacting Tektronix
Tektronix, Inc.
14150 SW Karl Braun Drive
P.O. Box 500
Beaverton, OR 97077
USA
For product information, sales, service, and technical support:
In North America, call 1-800-833-9200.
Worldwide, visit www.tektronix.com to find contacts in your area.
Warranty
Tektronix warrants that this product will be free from defects in materials and workmanship for a period of one (1) year from the date of
shipment. If any such product proves defective during this warranty period, Tektronix, at its option, either will repair the defective
product without charge for parts and labor, or will provide a replacement in exchange for the defective product. Parts, modules and
replacement products used by Tektronix for warranty work may be new or reconditioned to like new performance. All replaced
parts, modules and products become the property of Tektronix.
In order to obtain service under this warranty, Customer must notify Tektronix of the defect before the expiration of the warranty period
and make suitable arrangements for the performance of service. Customer shall be responsible for packaging and shipping the
defective product to the service center designated by Tektronix, with shipping charges prepaid. Tektronix shall pay for the return of the
product to Customer if the shipment is to a location within the country in which the Tektronix service center is located. Customer shall
be responsible for paying all shipping charges, duties, taxes, and any other charges for products returned to any other locations.
This warranty shall not apply to any defect, failure or damage caused by improper use or improper or inadequate maintenance and
care. Tektronix shall not be obligated to furnish service under this warranty a) to repair damage resulting from a ttempts by personnel
other than Tektronix representatives to install, repair or service the product; b) to repair damage resulting from improper use or
connection to incompatible equipment; c) to repair any damage or malfunction caused by the use of non-Tektronix supplies; or
d) to service a product that has been modified or integrated with other products when the effect of such modification or integration
increases the time or difficulty of servicing the product.
THIS WARRANTY IS GIVEN BY TEKTRONIX WITH RESPECT TO THE PRODUCT IN LIEU OF ANY OTHER WARRANTIES,
EXPRESS OR IMPLIED. TEKTRONIX AND ITS VENDORS DISCLAIM ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE. TEKTRONIX’ RESPONSIBILITY TO REPAIR OR REPLACE DEFECTIVE PRODUCTS
IS THE SOLE AND E XCLU S IVE REMEDY PROVIDED TO THE CUSTOMER FOR BREACH OF THIS WARRANTY. TEKTRONIX
AND ITS VENDORS WILL NOT BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES
IRRESPECTIVE OF WHETHER TEKTRONIX OR THE VENDOR HAS ADVANCE NOTICE OF THE POSSIBILITY OF SUCH
DAMAGES.
[W2 – 15AUG04]
Table of Contents
General Safety Summary ...... . . . . . .... . . . . . . ... . . . . . . .... . . . . . .... . . . . . . ... . . . . . . .... . . . . . ..... . . . . . .... . . . . . . ... . . . . . . .... . . . . . ... . iii
Compliance Information............................................................................................................... v
EMC Compliance................................................................................................................. v
Safety Compliance............................................................................................................... vi
Environmental C onsiderations – RSA6100A .. .... . . . . . .... . . . . . . .... . . . . . .... . . . . . . ... . . . . . . ... . . . . . . .... . . . . . .... . . . . . . ... . . vii
Environmental C onsiderations – RSA5100A .. .... . . . . . .... . . . . . . .... . . . . . .... . . . . . . ... . . . . . . ... . . . . . . .... . . . . . .... . . . . . . ... . viii
Preface................................................................................................................................. ix
Key Features .....................................................................................................................ix
Documentation ...................................................................................................................ix
Software Upgrades. . . . . . ... . . . . . . .... . . . . . .... . . . . . . .... . . . . . .... . . . . . . ... . . . . . . ... . . . . . . .... . . . . . .... . . . . . . ... . . . . . . ... . . . . . . ... x
Conventions Used in This Manual..... . . . . . . .... . . . . . . .... . . . . . . .... . . . . . . ... . . . . . . ..... . . . . . . ... . . . . . . .... . . . . . . ... . . . . . . . .... . x
Installation.............................................................................................................................. 1
Before Installation................................................................................................................ 1
RSA6100A Series Standard A ccessories ... . . . . . . ... . . . . . . .... . . . . . . .... . . . . . . ... . . . . . . .... . . . . . . ... . . . . . . .... . . . . . . .... . . . . . . . 1
RSA5100A Series Standard A ccessories ... . . . . . . ... . . . . . . .... . . . . . . .... . . . . . . ... . . . . . . .... . . . . . . ... . . . . . . .... . . . . . . .... . . . . . . . 3
Optional Accessories .. . . . . . . ... . . . . . . ... . . . . . . .... . . . . . .... . . . . . .... . . . . . . ... . . . . . . ... . . . . . . ... . . . . . . .... . . . . . .... . . . . . .... . . . . . 4
RSA6100A Series Options..... . . . . . . . ... . . . . . . .... . . . . . . ..... . . . . . . .... . . . . . . ... . . . . . . . .... . . . . . . .... . . . . . . .... . . . . . . . ... . . . . . . . 5
RSA5100A Series Options..... . . . . . . . ... . . . . . . .... . . . . . . ..... . . . . . . .... . . . . . . ... . . . . . . . .... . . . . . . .... . . . . . . .... . . . . . . . ... . . . . . . . 6
Operating Considerations........................................................................................................ 7
Connecting to the Instrument . . . . . . . .... . . . . . ..... . . . . . . ... . . . . . . .... . . . . . .... . . . . . . ... . . . . . . ..... . . . . . .... . . . . . . ... . . . . . . .... . . . 8
Powering Onthe Instrument..................................................................................................... 9
Powering Off the Instrument..................................................................................................... 9
Removing the Power............................................................................................................. 9
Adding an External Monitor..................................................................................................... 10
Inspecting the Instrument....................................................................................................... 14
User Maintenance . . . . . . .... . . . . . . .... . . . . . . . .... . . . . . . .... . . . . . . . .... . . . . . . .... . . . . . . . ... . . . . . . . .... . . . . . . . ... . . . . . . . ... . . . . . . . . 15
Operation.............................................................................................................................. 16
Getting Acquainted with Your Instrument .. . . . . . . .... . . . . . . ... . . . . . . ... . . . . . . .... . . . . . . .... . . . . . . ... . . . . . . ... . . . . . . .... . . . . . . .. 16
Basic Concepts.................................................................................................................. 27
Navigating Displays............................................................................................................. 29
Selecting Displays...............................................................................................................30
Connecting a S ignal.... . . . . . .... . . . . . . ... . . . . . . ... . . . . . . .... . . . . . .... . . . . . . ... . . . . . . ... . . . . . . ... . . . . . . .... . . . . . . .... . . . . . .... . . . 3 5
Starting and Stopping Acquisitions . . . . . .... . . . . . . ... . . . . . . ... . . . . . . .... . . . . . .... . . . . . . ... . . . . . . ... . . . . . . .... . . . . . .... . . . . . . .... 36
Markers.......................................................................................................................... 37
Touchscreen Actions............................................................................................................ 40
Printing .......................................................................................................................... 42
Saving Data ..................................................................................................................... 44
Recalling Data...................................................................................................................45
Advanced Techniques. . ... . . . . . . . ... . . . . . . ..... . . . . . . .... . . . . . . .... . . . . . . .... . . . . . . .... . . . . . . ..... . . . . . . ... . . . . . . . ... . . . . . . ..... 47
Index
Table of Content
s
RSA6100A Series & RSA5100A Series Quick Start User Manual i
Table of Content
s
ii RSA6100A Series & RS A5100A Series Quick Start User Manual
General Safety S
ummary
General Safet
Review the following safety precautions to avoid injury and prevent damage to this product or any products connected to it.
To avoid potential hazards, use this product only as specified.
Only qualified personnel should perform service procedures.
While using this product, you may need to access other parts of a larger system. Read the safety sections of the other
component manuals for warnings and cautions related to operating the system.
To Avoid Fire or Personal Injury
Use proper power cord. Use only the power cord specified for this product and certified for the country of use.
Ground the product. This product is grounded through the grounding conductor of the power cord. To avoid electric
shock, the
terminals of the product, ensure that the product is properly grounded.
Observe all terminal ratings. To avoid fire or shock hazard, observe all ratings and markings on the product. Consult the
product manual for further ratings information before making connections to the product.
The inputs are not rated for connection to mains or Category II, III, or IV circuits.
Power disconnect. The power cord disconnects the product from the power source. Do not block the power cord; it
must rem
grounding conductor must be connected to earth ground. Before making connections to the input or output
ain accessible to the user a t all times.
y Summary
Do not op
Do not o
qualified service personnel.
erate without covers.
perate with suspected failures.
Do not operate this product with covers or panels removed.
If you suspect that there is damage to this product, have it inspected by
Avoid exposed circuitry. Do not touch exposed connections and components when power is present.
Replace batteries properly. Replace batteries only with the specified type and rating.
Use proper fuse. Use only the fuse type and rating specified for this product.
Do not operate in wet/damp conditions.
Do not operate in an explosive a tmosphere.
Keep product surfaces clean and dry.
Provide proper ventilation.
proper ventilation.
Refer to the manual’s installation instructions for details on installing the product so it has
RSA6100A Series & RSA5100A Series Quick Start User Manual iii
General Safety S
Terms in This Manual
These terms may appear in this manual:
WARNING. Warning statements identify conditions or practices that could result in injury or loss of life.
CAUTION. Caution statements identify conditions or practices that could result in damage to this product or other property.
Symbols and Terms on the Product
These terms may appear on the product:
DANGER indicates an injury hazard immediately accessible as you read the marking.
WARNING indicates an injury hazard not immediately accessible as you read the m arking.
CAUTION indicates a hazard to property including the product.
The following symbol(s) may appear on the product:
ummary
iv RSA6100A Series & RSA5100A Series Quick Start User Manual
Compliance Info
rmation
Compliance In
This section lists the EMC (electromagnetic compliance), safety, and environmental standards with which the instrument
complies.
EMC Compliance
EC Declaration of Conformity – EMC
Meets intent of Directive 2004/108/EC for Electromagnetic Compatibility. Compliance was demonstrated to the following
specifications as listed in the Official Journal of the European Communities:
EN 61326-1:2006, EN 61326-2-1:2006. EMC requirements for electrical equipment for measurement, control, and
laboratory use.
CISPR 11:2003. Radiated and conducted emissions, Group 1, Class A
IEC 61000-4-2:20
IEC 61000-4-3:2002. RF electromagnetic field immunity
IEC 61000-4-4:2004. Electrical fast transient/burst immunity
IEC 61000-4-5:2001. Power line surge immunity
IEC 61000-4-6:2003. Conducted RF immunity
IEC 61000-4-11:2004. Voltage dips and interruptions immunity
1234
formation
01. Electrostatic discharge immunity
5
6
7
EN 61000-3-2:2006. AC power line harmonic emissions
EN 61000-3-3:1995. Voltage changes, fluctuations, and flicker
European Contact.
Tektronix UK, Ltd.
Western Peninsula
Western Road
Bracknell, RG12 1RF
United Kingdom
1
This product is intended f or use in nonresidential areas only. Use in residential areas may cause electromagnetic interference.
2
Emissions which exceed the levels required by this standar
3
To ensure compliance with the EMC standards listed here, high quality shielded interface cables should be used.
4
At the IEC 61000-4-11 Voltage-Interruption Transient Immunity test at 0% for 250 cycles, the EUT reboots and can take greater
than 10 seconds to recover.
5
Performance degradation information for the IEC 61000-4-3 test: Residual spurious signals can typically increase to -55 dBm with
exposure to the disturbance levels of this test.
6
Performance degradation inf
either 55 dB below reference level or -75 dBm, with exposure to the disturbance levels of t his test.
7
Performance Criterion C applied at the 70%/25 cycle Voltage-Dip and the 0%/250 cycle Voltage-Interruption test levels
(IEC 61000-4-11).
ormation for the IEC 61000-4-6 test: Residual spurious signals can typically increase to the worse of
d may occur when this equipment is connected to a test object.
RSA6100A Series & RSA5100A Series Quick Start User Manual v
Compliance Info
rmation
Australia / New Zealand Declaration of Conformity – E MC
Complies with the EMC provision of the Radiocommunications Act per the following standard, in accordance with ACMA:
CISPR 11:2003. Radiated and Conducted Emissions, Group 1, Class A, in accordance with EN 61326-1:2006 and
EN 61326-2-1:2006.
Safety Compliance
EC Declaration of Conformity – Low Voltage
Compliance was demonstrated to the following specification as listed in the O fficial Journal of the European Communities:
Low Voltage Directive 2006/95/EC.
EN 61010-1: 2001. Safety requirements for electrical equipment for measurement control and laboratory use.
U.S. Nationally Recognized Testing Laboratory Listing
UL 61010-1:2004, 2ndEdition. Standard for electrical measuring and test equipment.
Canadian Certification
CAN/CSA-C22.2 No. 61010-1:2004. Safety requirements for electrical equipment for measurement, control, and
laboratory use. Part 1.
Additional Compliances
IEC 61010-1: 2001. Safety requirements for electrical equipm
ent for measurement, control, and laboratory use.
Equipment Type
Test and measuring equipment.
Safety Class
Class 1 – grounded product.
Pollution Degree Description
A measure of the contaminants that could occur in the environment around and within a product. Typically the internal
environment inside a product is considered to be the same as the external. Products should be used only in the environment
for which they are r ated.
Pollution Degree 1. No pollution or only dry, nonconductive pollution occurs. Products in this category are generally
encapsulated, hermetically sealed, or located in clean rooms.
Pollution Degree 2. Normally only dry, nonconductive pollution occurs. Occasionally a temporary conductivity that is
caused by condensation must be expected. This location is a typical office/home environment. Temporary condensation
occurs only when the product is out of service.
vi RSA6100A Series & RSA5100A Series Quick Start User Manual
Compliance Info
Pollution Degree 3. Conductive pollution, or dry, nonconductive pollution that becomes conductive due to condensation.
These are shelt
sunshine, rain, or direct wind.
Pollution Degree 4. Pollution that generates persistent conductivity through conductive dust, rain, or snow. Typical
outdoor locations.
ered locations where neither temperature nor humidity is controlled. The area is protected from direct
rmation
Pollution De
Pollution Degree 2 (as defined in IEC 61010-1). Note: Rated for indoor use only.
gree
Environmental Considerations – RSA6100A
This secti
Product End-of-Life Handling
Observe the following guidelines when recycling an instrument or component:
Equipment Recycling. Production of this equipment required the extraction and use of natural resources. The
equipme
product’s end of life. In order to avoid release of such substances into the environment and to reduce the use of natural
resources, we encourage you to recycle this product in an appropriate system that will ensure that most of the materials are
reused o
on provides information about the environmental impact of the product.
nt may contain substances that could be harmful to the environment or human health if improperly handled at the
r recycled appropriately.
This symbol indicates that this product complies with the applicable European Union requirements according
ctives 2002/96/EC and 2006/66/EC on waste electrical and electronic equipment (WEEE) and
to Dire
batteries. For information about recycling options, check the Support/Service section of the Tektronix Web
site (www.tektronix.com).
Mercury Notification. This product uses an LCD backlight lamp that contains mercury. Disposal may be regulated due
to environmental considerations. Please contact your local authorities or, within the United States, refer to the E-cycling
Central Web page (www.eiae.org) for disposal or recycling information.
Restriction of Hazardous Substances
This product has been classified as Monitoring and Control equipment, and is outside the scope of the 2002/95/EC RoHS
Directive.
RSA6100A Series & RSA5100A Series Quick Start User Manual vii
Compliance Info
rmation
Environmental Considerations – RSA5100A
This section provides information about the environmental impact of the product.
Product End-of-Life Handling
Observe the following guidelines when recycling an instrument or component:
Equipment Recycling. Production of this equipment required the extraction and use of natural resources. The
equipment may contain substances that could be harmful to the environment or human health if improperly handled at the
product’s end of life. In order to avoid release of such substances into the environment and to reduce the use of natural
resources, we encourage you to recycle this product in an appropriate system that will ensure that most of the materials are
reused or recycled appropriately.
This symbol indicates that this product complies w ith the applicable European Union requirements according
to Directives 2002/96/EC and 2006/66/EC on waste ele ctrical and electronic equipment (WEEE) and
batteries. For information about recycling options, check the Support/Service section of the Tektronix Web
site (www.tektronix.com).
Mercury N
to environmental considerations. Please contact your local authorities or, within the United States, refer to the E-cycling
Central Web page (www.eiae.org) for disposal or recycling information.
otification.
This product uses an LCD backlight lamp that contains mercury. Disposal may be regulated due
Perchlorate Materials. This product contains one or more type CR lithium coin cell batteries. According to the
state of California, CR lithium coin cells are classified as perchlorate materials and require special handling. See
www.dtsc.ca.gov/hazardouswaste/perchlorate for additional information.
Restriction of Hazardous Substances
roduct has been classified as Monitoring and Control equipment, and is outside the scope of the 2002/95/EC RoHS
This p
Directive.
viii RSA6100A Series & RSA5100A Series Quick Start User Manual
Preface
This manual describes the installation and basic operation of the RSA6100A Series of Real-Time Spectrum Analyzers and
RSA5100A Series Real-Time Signal Analyzers. For m ore detailed information, see the online help for your instrument.
RSA6106A
RSA6114A
RSA6120A
RSA5103A
RSA5106A
Key Features
The RSA6100A Series and RSA5100A Series are a family of high-performance real-time analyzers. Key features include:
Digital Phosphor Spectrum analysis, which greatly reduces the amount of time to recognize and identify a fault
DPX Density triggering to easily capture instabilities, transients and hidden signals that are impossible for other signal
analyzers to catch
Preface
Conventional spectrum analysis controls and functions including fast tuning, markers, phase noise, spurious and
other measurements
Easy event-based capture o f transient RF signals by
Tektronix-exclusive Frequency M ask Triggering
Time domain triggering capability: Runt Triggers, Holdoff Trigger, and Time Qualification to all of the instrument triggers
(Option 200)
Multi-domain displays that provide an intuitive understanding of time-varying RF signals
Conventional Vector Signal Analysis capability available (Option 21) with modulation analysis for >20 popular modulation
formats
Seamless capture of signals in up to 110 MHz spans (RSA6100A Series) or 85 MHz spans (RSA5100A Series)
Documentation
The following documentation is available with your Tektronix RSA6100A Series Spectrum Analyzer or RSA5100A Series
Signal Analyzers. For the most current documentation, refer to the Tektronix Web site.
To read about Use these documents
Installation and operation
(overviews)
In-depth operation and
user interface help
Application examples Application Examples Manual
triggering on changes in the frequency domain using
Quick Start User Manual
The quick start user manual contains general information about how to put your instrument
into service and guides to user interface controls.
Online help
The online help contains detailed information about how to operate the instrument.
This manual provides practical e xamples o f using the analyzer to accomplish tasks.
RSA6100A Series & RSA5100A Series Quick Start User Manual ix
Preface
To read about Use these documents
Programming commands Programmer Manual
Specification
performance verification
User service
s and
Software Upgrades
Software option upgrades are available. Software upgrades for options become operational only after you enter a valid
option key for the specific analyzer model and serial number.
To check for upgrades:
The programming commands for the RSA6100A Series and RSA5100A are located in a
PDF file locate
Specification
This manual contains the instrument specifications and a procedure to check instrument
performance against warranted characteristics. This manual is in a PDF file located
on the Docume
Service Man
A manual that provides a list of replaceable parts, care and maintenance information, and
information for servicing the instrument to the module level. This manual is in a PDF file
located on t
d on the Documents CD.
s and Performance Verification Manual
nts CD.
ual.
he Product Documentation CD.
1. Use your Web browser to go to www.tektronix.com/software.
2. Enter the product name (for example RSA6120A or RSA5106A ) to find available software upgrades.
Conventions Used in This M anual
lowing icons are used throughout this manual:
The fol
Sequen
Step
ce
Front panel
power
Connec
power
t
Network
PS2 SVGA USB
x RSA6100A Series & RSA5100A Series Quick Start User Manual
Installation
Before Installation
Unpack the instrument, and check that you received all items listed as Standard Accessories. Optional accessories and
instrument options are also listed in this section. Check the Tektronix Web site (www.tektronix.com) for the most current
information.
RSA6100A Series Standard Accessories
Your instrument comes with the following accessories: quick start user manual (languages are listed below), programmer
manual (on CD), specifications and performance verification manual (on CD), declassification and security instructions
(on CD), service manual (on CD), power cord, BNC-N adapter (RSA6106A and RSA6114A only, Tektronix part number
103-0045-XX), Jack-to-Jack SMA adapter (RSA6120A only, Tektronix part number 131-8508-XX) 50 Ω SMA terminator
(RSA6120A only, Tektronix part number 015-1022-XX), USB keyboard, USB mouse, and instrument front cover.
Documents
RSA6100A Series Real-Time Spectrum Analyzers Quick Start User Manual is available in the following languages:
Installation
English, Tektronix part number 071-2838-XX.
Simplified Chinese, Tektronix part number 071-2839-XX.
Japanese, Tektronix part number 071-2840-XX.
Russian, Tektronix part number 071-2841-XX.
RSA6100A Series and RSA5100A Series Product Documentation CD, Tektronix part number 063-3930-XX.
The Product Documentation CD contains PDF versions of the following manuals:
RSA6100A Series Real-Time Spectrum Analyzers, RSA5100A Series R eal-Time Signal Analyzers Quick Start User
Manual,
in English (this manual), Japanese, Russian and Simplified Chinese.
RSA6100A Series Real-Time Spectrum Analyzers, RSA5100A Series Real-Time Signal Analyzers Application
Examples Manual,
Tektronix part number 071-2834-XX.
RSA6100A Series Real-Time Spectrum Analyzers, Printable Online Help,
Tektronix part number 077-0169-XX.
RSA6100A Series Real-Time Spectrum Analyzers, RSA5100A Series Real-Time Signal Analyzers Programmer
Manual,
Tektronix part number 077-0523-XX.
RSA6100A Series Real-Time Spectrum Analyzers Service Manual,
Tektronix part number 077-0250-XX.
RSA6100A Series Real-Time Spectrum Analyzers Specifications and Performance Verification Manual,
Tektronix part number 077-0251-XX.
RSA6100A Series Real-Time Spectrum Analyzers Declassification and Security Instructions,
Tektronix part number 077-0170-XX.
RSA6100A Series & RSA5100A Series Quick Start User Manual 1
Installation
Power Cords
The RSA6100A Series Real-Time Spectrum Analyzers are shipped with one of the following power cord options. Power
cords for use in North America are UL listed and CSA certified. Cords for use in areas other than North A merica are approved
by at least one authority acceptable in the country to which the product is shipped.
International Power Plugs
Opt. A0 - North America power
Opt. A1 - Universal EURO power
Opt. A2 - United Kingdom power
Opt. A3 - Australia power
Opt. A4 - 240 V, North America power
Opt. A5 - Switzerland power
Opt. A6 - Japan power
Opt. A10 - China power
Opt. A11 - India power
Opt. A12 - Brazil power
Opt. A99 - No power cord
2 RSA6100A Series & RSA5100A Series Quick Start User Manual
RSA5100A Series Standard Accessories
Your instrument comes with the following accessories: quick start user manual (languages are listed below), programmer
manual (on CD), specifications and performance verification manual (on CD), declassification and security instructions (on
CD), service manual (on CD), power cord, BNC-N adapter, USB keyboard, USB mouse, and instrument front cover.
Product Documentation
RSA6100A Series Real-Time Spectrum Analyzers, RSA5100A Series Real-Time Signal Analyzers Quick Start User
Manual is available in the following languages:
English, Tektronix part number 071-2838-XX.
Simplified Chinese, Tektronix part number 071-2839-XX.
Japanese, Tektronix part number 071-2840-XX.
Russian, Tektronix part number 071-2841-XX.
RSA6100A Series, RSA5100A Series Product Documentation CD, Tektronix part number 063-4314-XX.
The Produ
ct Documentation CD contains PDF versions of the following manuals:
Installation
RSA6100A
Manual,
in English, Japanese, Russian and Simplified Chinese.
RSA6100A Series Real-Time Spectrum Analyzers, RSA5100A Series Real-Time Signal Analyzers Application
Example
Tektronix part number 071-2834-XX.
RSA5100A Series Real-Time Signal Analyzers, RSA6100A Series Real-Time Spectrum Analyzers Printable Online
Help,
Tektro
RSA610
Manual,
Tektronix part number 077-0523-XX.
RSA5100A Series Real-Time Spectrum Analyzers Service Manual,
Tektr
RSA5
Tektronix part number 077-0520-XX.
RSA5100A Series Real-Time Spectrum Analyzers Declassification and Security Instructions,
Tektronix part number 077-0521-XX.
er Cords
Pow
Series Real-Time Spectrum Analyzers, RSA5100A Series Real-Time Signal Analyzers Quick Start User
s M anual,
nix part number 077-0519-XX.
0A Series Real-Time Spectrum Analyzers, RSA5100A Series Real-Time Signal Analyzers Programmer
onix part number 077-0522-XX.
100A Series Real-Time Signal Analyzers Specifications and Performance Verification Manual,
The RSA5100A Series Real-Time Spectrum Analyzers are shipped with one of the following power cord options. Power
cords for use in North America are UL listed and CSA certified. Cords for use in areas other than North America are approved
by at least one authority acceptable in the country to which the product is shipped.
RSA6100A Series & RSA5100A Series Quick Start User Manual 3
Installation
International Power Plugs
Opt. A0 - North America power
Opt. A1 - Universal EURO power
Opt. A2 - United Kingdom power
Opt. A3 - Australia power
Opt. A4 - 240 V, North America power
Opt. A5 - Switzerland power
Opt. A6 - Japan power
Opt. A10 - China power
Opt. A11 - India power
Opt. A12 - Brazil power
Opt. A99 - No power cord
Optional Accessories
RSA6100
RSA5100A
ASeries
RSA61RHD - Provides an additional removable hard disk drive for use with Option 06
065-0765-XX - A dditional removable solid-state hard drive for use with Option 08
(Microsoft Windows XP Embedded and instrument SW pre-installed)
RTPA2A - Real-Time Spectrum Analyzer Probe Adapter; Supports TekConnect probes P7225, P7240, P7260, P7330,
P7313, P7350, P7350SMA, P7380, P7380SMA.
RSAVu - Offline analysis software based on the RSA3000 platform for analysis supporting 3G wireless standards,
IEEE 802.11a/b/g/n).
WLAN (
IQWIMAX, and RSALTE from LitePoint – Third-party solutions that enable WiMax and LTE analysis with the
RSARSA000 Series.
065-0xxx-00 – Additional Removable Hard Drive for use with Opt. 56 (Windows 7 and instrument software pre-installed).
Transit Case – Tektronix part number 016-1963-00.
4 RSA6100A Series & RSA5100A Series Quick Start User Manual
RSA6100A Series Options
You can add the following options to your analyzer:
Option 01 - Adds 10 MHz to 3 GHz Pre-Amplifier
Option 02 - Adds frequency mask triggering and RAM expansion
Option 05 - Adds digital IQ output and 500 MHz analog IF output
Option 06 - Adds a removable hard disk drive (not compatible with Option 07 or Option 08)
Option 07 - Adds a DVD±RW drive, no-cost option (not compatible with Option 06 or Option 08)
Option 08 - Adds a removable solid-state hard drive (not compatible with Option 06 or Option 07)
Option 11 - Adds Phase Noise and Jitter Measurement
Option 12 - Adds Settling Time Measurement (Frequency and Phase)
Option 20 - Adds advanced signal analysis (including pulse measurements)
Option 21 - Adds general-purpose digital modulation analysis
Option 110 - Adds 110 MHz real-time capture bandwidth
Option 200 - Advanced DPX and Triggers
Installation
RSA56KR – Rackmount for RSA5100A Series and RSA6100A Series analyzers
RSA6100A Series & RSA5100A Series Quick Start User Manual 5
Installation
RSA5100A Series Options
You can add the following options to your analyzer:
Option 11 - Adds Phase Noise and Jitter Measurement.
Option 12 - Adds Settling Time Measurement (Frequency and Phase).
Option 20 - Adds advanced signal analysis (including pulse measurements).
Option 21 - Adds general-purpose digital modulation analysis.
Option 40 - Adds 40 MHz real-time capture bandwidth.
Option 85- Adds 85 MHz real-time c apture bandwidth.
Option 51 - Adds 10 MHz to 3 GHz Pre-Amplifier.
Option 52 - Adds frequency mask triggering.
Option 53 - Adds Memory, 4 GB Acquisition Memory Total.
Option 56 - Adds a removable hard disk drive (not compatible with Option 57 or Option 59).
Option 57 - Adds a CD-R/W drive (not compatible with Option 56).
Option 59 - Adds a internal hard disk drive (not compatible with Option 56).
Option 200 - Adds Advanced DPX with Density, Time Qualified and Runt Triggers and Zero-Span.
Option 5040 – Combines Option 50 (Preamp) and Option 40 (40 MHz Acquisition BW). Mutually exclusive with
Options 50 and 40.
Option 5085 – Combines Option 50 (Preamp) and Option 85(85 MHz Acquisition BW). Mutually exclusive with Options
50 and 40.
RSA56KR – Rackmount for RSA5100A Series and RSA6100A Series analyzers.
6 RSA6100A Series & RSA5100A Series Quick Start User Manual
Operating Considerations
Power supply requirements
Source voltage and frequency Power consumption
100 – 240 V
115 V
RMS
, 400
, 50/60 Hz
RMS
Hz
Installation
450 W maximum (all models)
Environmen
Characteristic Description
RSA6100A Series Operating temperature +5 °C to +50 °C (+5 °C to +40 °C; when accessing the DVD drive or optional
RSA5100A Series Operating temperature +10 °C to +40 °C
Non-operating temperature
RSA6100A Humidity 90% relative humidity at 30 °C (non-condensing)
RSA5100A Humidity 90% up to 30 °C (non-condensing)
Altitude:
Opera
Non-operating
Cooling clearance
Bottom
Side
tal requirements
ting
s and back
removable hard-disk drive)
-20°Cto+60°C
80% maxi
Maximum wet-bulb temperature 29 °C
80% relative humidity m aximum when accessing the DVD drive
Above 3
Up to 3
12190 m (40,000 ft)
20 mm (0.79 in)
50 mm (1.97 in)
mum when accessing the DVD drive
0 °C it is limited by maximum wet-bulb temperature 29 °C
000 m (9843 ft)
RSA6100A Series & RSA5100A Series Quick Start User Manual 7
Installation
CAUTION. To ensure proper cooling, do not operate the instrument on its side. Operate the instrument only when it is resting
on its feet
WARNING. To avoid personal injury, take extra care when lifting or moving the spectrum analyzer. The instrument is
somewhat heavy and requires extra care when moving it.
, located on the bottom of the case. Maintain at least 2 inches (5 cm.) clearance around ventilation openings.
Connecting to the Instrument
Connecting to a Network
Connect your keyboard, mouse, printer, and other accessories to your instrument before applying power. (Accessories w ith
USB connectors can be c
You can connect your in
network for printing, file sharing, Internet
access, and other functions. C onsult your
network administrat
Windows utilities to configure the instrument
for your network.
Quick Tip
If you connect your
regular approved operating system updates, and using up-to-date antivirus software.
onnected before or after applying power.)
strument to a
or and use the standard
instrument to a network, you should protect your instrument by using an internet firewall, installing
8 RSA6100A Series & RSA5100A Series Quick Start User Manual
Powering On the Instrument
Installation
Powering O
ff the Instrument
Removing the Power
RSA6100A Series & RSA5100A Series Quick Start User Manual 9
Installation
Adding an External Monitor
Use the following procedure to add an external monitor for dual monitor configuration. Both the analyzer and the second
monitor must have the color set to True Color.
1. Power off the analyzer and the external
monitor.
2. Connect the external monitor to the
analyzer.
3. Power on the analyzer and the external
monitor.
10 RSA6100A Series & RSA5100A Series Quick Start User Manual
Loading...