Tektronix RSA5600RACK Rackmount Kit Field Install Instructions

xx

RSA5600RACK

ZZZ

Rackmount Kit

Installation Instructions

www.tek.com

P071346801*

*

071-3468-01

Copyright © Tektronix. All rights reserved. Licensed software products are owned by Tektronix or its subsidiaries
or suppliers, and are protected by national copyright laws and international treaty provisions.

Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication
supersedes that in all previously published material. Specifications and price change privileges reserved.

TEKTRONIX and TEK are registered trademarks of Tektronix, Inc.

Contacting Tektronix

Tektronix, Inc.
14150 SW Karl Braun Drive
P.O. Box 5 0 0
Beaverto
USA

For product information, sales, service, and technical support:

n, OR 97077

In North America, call 1-800-833-9200.
Worldwide, visit www.tek.com to find contacts in your area.

General safety

summary

Review the following safety precautions to avoid injury and prevent damage to
this product or any products connected to it.

To avoid potential hazards, use this product only as specified.

Only qualified personnel should perform service procedures.

To avoid damage to

equipment and personal

injury

Contacting Tektronix

Do not exceed rackmount weight ratings. Use this rackmount kit only for

RSA503A, RSA507A, RSA603A, and RSA607A instruments.

Use proper hardware. Do not interchange hardware. Use only specified mounting
screws.

Use care when installing and removing product from rack. Avoid pinching
fingers and hands when installing and removing. Do not force the product when

ng. Gently pull the product out when removing.

installi

Use only with specified products. Do not use rackmount on products for which
it was not intended. Refer to individual product manuals for details or contact
Tektronix Customer Service when in doubt.

Tektronix, Inc.
14150 SW Karl Braun Drive
P.O. Box 500
Beaverton, OR 97077
USA

For product information, sales, service, and technical support:

In North America, call 1-800-833-9200.

Worldwide, visit www.tek.com to find contacts in your area.

RSA5600RACK Rackmount Kit Installation Instructions 1

Kit description

Kit description

The rackmount kit is a collection of parts that, once installed, configures the
following Tektronix Spectrum Analyzer products for mounting into a standard
19-inch equi

pment rack.

Required equipment

Kit parts list

Products

RSA503A

RSA507A

RSA513A

RSA518A

RSA603A

RSA607A

Phillips #2 screwdriver

11/32 socket or nut driver

Torx T-15

Torx T-20

The following table lists the parts contained in this kit. Use the associated figure
to identify the parts and to assemble the kit. (See Figure 1.)

Table 1: RSA5600RACK Rackmount kit parts list

Item
no. Qty. Description Tektronix part number

11

21

31

41

5

61

7

81

91

10 1

1

2

BRACKET, FACEPLATE, HANDHELD

BRACKET, FACEPLATE, BENCH, ONE UNIT

BRACKET, FACEPLATE, COVER, CABLE PASS-THRU

BRACKET, FACEPLATE, BENCH, TWO UNIT

BRACKET, RACK, LEFT, FRONT

BRACKET, RACK, LEFT, BACK

RACK, SLIDE, BALL BEARING, 18 INCHES LONG

BRACKET, BASE, RACK KIT

BRACKET, RACK, RIGHT, BACK

Strap for securing RSA500

407-5950-00

407-5951-00

407-5953-00

407-5952-00

407-5970-00

407-5969-00

351-1153-00

407-5949-00

407-5971-00

—

2 RSA5600RACK Rackmount Kit Installation Instructions

Kit description

Table 1: RSA5600RACK Rackmount kit parts list , (cont.)

Item
no. Qty. Description Tektronix part number

11 1

12 1

BRACKET, RACK, RIGHT, FRONT

Bag of screws and nuts

bag

407-5972-00

—

Figure 1: Rackmount kit assembly

Installation

For all products being

installed

RSA5600RACK Rackmount Kit Installation Instructions 3

This rack frame comes completely assembled with the façade and closure plate in
place. Use the following procedure and refer to the illustration to assemble the
rackmount hardware and install the instrument into the rack. (See Figure 1.)

1. Lay out the right front (item 11) and right rear (item 9) brackets onto a table.
Imagine you are facing the rack and align the brackets with the securing
ears facing out.

2. Take one slide (item 7) and notice that each end has a rubber détente. One is a
rectangle and one has three circles.

3. Place that slide into the right front and rear brackets, oriented so that the
rectangular détente is closest to you and facing outward.