Tektronix P7508, P7513A User manual

P7508 & P7513A TriMode Probes
Manuals and Related Documentation

The P7500 Series TriMode Probe manuals that are included with your P7508 and
P7513A probes contain all of the operating information necessary for you to
use these probes. However, the probe connection to the DC calibration board is
slightly different and is shown on the back of this sheet.

The information and specifications for the P7508 and P7513A probes in this
sheet supersede the information in the P7500 Series Technical Reference on the
Documenta

tion CD.

Probe
model Characteristic Probe only

P7508

513A

P7

P7508 &
P7513A

1

Measurements taken using an embedded probe fixtureanda250mVstep@18°Cto28°C(64°Fto82°F).

2

Warranted specification

Bandwidth

Rise time

CMRR >60 dB a

DMRR >40 dB

nnel isolation

Cha

Delay tim e 5.76 ns, ±0.1 ns

Channel isolation >15 dB to 7 GHz

Delay tim e 5.76 ns, ±0.1 ns

robe length

P

DC Calibration Board
and Socket Cable
(standard accessories)

Optional accessories
for the P7508 &
P7513A probes

>8 GHz >8 GHz >8 GHz

10–90% 55 ps

20–80%

>40dBto50MHz

>30dBto1GHz

>25 dB

>20dBto8GHz

>30dBto1GHz

>25dBto4GHz

>20 d

>40dBto50MHz

>30

>20dBto4GHz

>12dBto8GHz

>8 dB to 13 GHz

1.3 m (51.6 in) (End-to-end with no accessories attached)

oard

B

Socket Cable

Antistatic wrist strap

Bullet removal tool

Replacement bullets

1

2

2

35 ps

tDC

to4GHz

to 50 MHz

Bto8GHz

dBto1GHz

Probe with
P75TLRST solder tip

10–90% 55 ps

20–80%

>60 dB a

>40dBto50MHz

>30 dB to 1 GHz

>25 dB

>20 dB to 8 GHz

>40 dB

>30 dB to 1 GHz

>25 dB to 4 GHz

>20 d

>40dBto50MHz

>30

>15 dB to 4 GHz

>10 dB to 8 GHz

T

Tektronix part number 020-2954-XX

Order Tektronix part number 006-3415-XX

Order Tektronix part number 003-1896-XX

Order Tektronix part number 013-0359-XX

35 ps

tDC

to 4 GHz

to 50 MHz

Bto8GHz

dB to 1 GHz

ektronix part number 067-1967-XX

Probe with
P75PDPM adapter

10–90% 55 ps

20–80%

>60 dB a

>40dBto50MHz

>30dBto1GHz

>25 dB

>20dBto8GHz

Not ap

Not applicable

35 ps

tDC

to4GHz

plicable

www.tektronix.com
Copyright © Tektronix

*P001144900*

001-1449-00

P7508 & P7513A TriMode Probes Manuals and Related Documentation

DC Calibration Board

Connection

When you perfor
P7513A probes, you must use the Socket Cable included with the probes to
connect between the probe and the board. See the illustration below.

m a functional check or DC calibration on the P7508 and

Figure 1: Connecting the P7508 and P7513A probes to the DC Calibration Board with the Socket Cable

For future reference, s ave this document with your probe documentation kit.

2 P7508 & P7513A TriMode Probes Supplement