Tektronix P5122, P5100, P5120, P6015A DATASHEET

Passive High-voltage Probes

P5100 • P5120 • P5122 • P6015A Data Sheet

P5122

For TPS2000 Series Only

DC to 200 MHz

P5120

Features & Benefits

P5100

DC to 250 MHz

1000 V CAT III (2500 V DC + Peak AC)

100X with Readout Coding

UL3111-1, EN61010-1, IEC61010-2 -031, CSA1010.1, CSA1010.2.031

7 to 30 pF Compensation Range

P5120

For TPS2000 Series

DC to 200 MHz

1000 V

Floatableupto600V

Preferred Probe for Ripple Measurements

20X

15 to 25 pF Compensation Range

UL61010B-2-031, EN61010-2-031, IEC61 010-2-031, CSA61010.2.031

RMS

CAT II

CAT II or 300 V

RMS

RMS

CAT III

1000 V

Floatable up to 600 V

100X

IEC61010-031

CATII when DC-coupled*

RMS

RMS

CATIII

1

P6015A

HighVoltage–20kVDC/40kVPeak(100msPulseWidth)

High Bandwidth – 75 MHz

Silicone Dielectric

Optional 1000X Readout Coding

Wide Compensation Range (7-49 pF)

Heavy-duty Versatile Ground Lead and Alligator Clip

Applications

Power Supply Design

Design Motor Drive

Electronic Ballast

Power Semiconductors

Switch Mode Control

UPS Systems

Power Converters

*1The P5122 probe should not be used for AC-coupled measurements on signals with greater than 300 V DC

offset. The P5120 is the recommended probe for measuring ripple on high-voltage DC supplies.

Data Sheet

P5120 and P 5122 IsolatedChannel™
Applications

In many applications, it is important to be able to isolate the measurement
from earth ground and also to isolate t he common voltage between
channels. The P5120 or P5122, coupled with the TPS2000 Series digital
storage oscil
earth ground and full isolation between the channels. The P5120 is the
recommended probe for measuring ripple on high-voltage DC supplies. T he
P5122 probe should not be used for AC-coupled measurements on signals
with greater than 300 V DC offset.

loscopes, deliver both the isolation for the measurem ent from

P6015A

P5100 High-voltage Probe

The P5100 is a low input capacitance high-voltage probe (2.5 kV) designed
for higher-frequency applications. The probe can be compensated to match
plug-ins and oscilloscopes with nominal input capacitances of 7-30 pF. A
variety of screw-on accessories provide easy connection to the device
under test.

P6015A High-v

For heavy-duty high-performance measurements of voltages over 2.5 kV,
the P6015A is
to 20 kV
bandwidth enables you to capture fast, high-voltage signals.

The P6015A uses an environmentally safe silicone compound for a
dielectric and never needs refilling. Other features include: A 7-49 pF
compensation range, small compensation box that fits on adjacent amplifier
inputs, and a readout option for use with most Tektronix digital scopes. With
the readout option, displayed voltage amplitude values will be the actual
signal value

Note: Using the readout version with other than Tektronix digital scopes
may result i

the industry standard. You can measure DC voltages up

and pulses up to 40 kV (peak, 100 ms duration). The 75 MHz

RMS

rather than understated by a factor of 1,000 .

n an erroneous readout display.

oltage Probe

2 www.tektronix.com