Tektronix P3410, P3420 Primary User
P3410 and P3420 Instructions
Instructions
This package contains either a P3410 TTL pod or a P3420 variable
pod. T welve cables are supplied with each pod (012-1502-XX for
the P3410 and 012-1504-XX for the P3420). Both pods are designed
to be used with the T ektronix DG2020 or DG2020A Data Generator.
Refer to Figure 1 to determine which pod you are using.
Information for installation, operations, specifications, and
accessories can be found in the DG2020 or DG2020A User Manual.
The following instruction describes about the cable connection only
between the Pod and the DG2020A. However, if your data generator
is the DG2020, you can also read this instruction as replacing
DG2020A with DG2020.
Precaution for Connecting Cable
CAUTION. Make sure that you have correctly inserted the cable
plug in the DG2020A and the pod before turning on power. The
yellow wire end of the connector must be aligned with the
triangular yellow index mark on the DG2020A or pod.
Incorrectly connected cables will damage the DG2020A and the
pod.
Note that the connectors on the DG2020A rear panel are installed
with the tab slot down, and the connector on the pod rear panel is
installed with the tab slot up (see Figure 2).
T o connect a cable between the
wire end of the cable connector with the triangular yellow index
mark on the DG2020A or pod connector. Doing this also correctly
aligns the connector alignment tab. See Figure 2. Then carefully but
firmly insert the cable connector into the
For further information for connection, refer to the DG2020A User
Manual titled DG2020A Data Generator With P3410 & P3420 Pods.
DG2020A and a pod, align the yellow
DG2020A or pod connector.
P3410 Front Panel
P3420 Front Panel
Figure 1: P3410 and P3420 front panels
Pod Rear Panel
Tab Slot
Yellow Index
Mark
Yellow Index
Mark
To connect a cable between the DG2020A and a
pod, align the yellow wire end of the cable connector
with the triangular yellow index mark on the
DG2020A or pod connector. Doing this also correctly
aligns the connector alignment tab. Then carefully
but firmly insert the cable connector into the
DG2020A or pod connector.
Yellow Wire
Cable
DG2020A Rear Panel
Tab
Tab Slots
Figure 2: Yellow index mark and yellow wire for cable connection
ອᛱᓢᡆώᔧ
F
Copyright © Tektronix Japan, Ltd. All rights reserved.
C
T
I
S
T
T
T
ёубȼиϋϏ P3410 ി TTL ѝущϞοϏ P3420 ിѐѪТіѫȦ
ѝущώΤκϬΫώѝущάᓾσφΤϞιȣϞοȢᘸၠТЯлеѪψη
φѝущᡑϋ
1 ༲) ΪϨϓТЯлеѪϲδᔧίπεΤȣϊΪȢбȼіѫȦлуш
ώᙴᙊᗖϏྡώψΪϪχιȣ
H P3410 ിᡑбȼіѫȦлуш : 012-1502-XX
H P3420 ിᡑбȼіѫȦлуш : 012-1504-XX
ѝущώበᜡȢཅᡍȢΪϨϓТЯлеѪϋτΤφϏ DG2020ി
ϞοϏ
DG2020A ിᚸѦȼжȦўыѥТѫϲ༲ηφίπεΤȣ
12 лушώбȼіѫάᒱອεϬφΤϞιȣѝущ (ᅞ
Instructions
P3410 TTL Pod
P3420 Variable Pod
ϊΪγώФѳйшѩЯзѧѳϏȢ
DG2020ിϋዐηφϢᒱᡍϋᐬεϬϞιȣ
бȼіѫᇜኳώໝώ፭
፭ȧбȼіѫȦїѩаϲქ઼ౕϋηφ DG2020A ിϞοϏѝущώ
гэЯпϋᇜኳηϊΤχίπεΤȣбȼіѫȦїѩаϲქ઼ϲౕϋᇜኳ
ηοϞϞ
ૡዧϊᑅάϬȢмэѬȼпΪϨϓѝущϋኻၽϲᠿΨϞιȣ
DG2020A ിᙴёэѫώѝущᇜኳᡑгэЯпψѝущᙴёэѫώ
гэЯпϏȢпіȦйѭушৌፖάქ઼ౕέϋϪᙕαϩϬφΤϫγ
ψϋ፭ηφίπεΤ
DG2020A ിψѝущϲᇜኳιϫໝϋϏȢгэЯпȦїѩаώпіψг
эЯпώпіȦйѭушȢΪϨϓбȼіѫώફᄧώѩФѳ
wire)
εΤȣᅞ
νώኾώᇜኳώნ໙ϋτΤφϏ
ϲ༲ηφίπεΤȣ
DG2020A ിώᑅරϲᓾϬϫψȢDG2020A ിΫϩѝущϋ
(ᅞ 2 ༲)ȣ
ψгэЯпώફᄧώўȼЯ (Yellow index mark) ϲϯλφίπ
2 ϲ༲ηφίπεΤȣ
DG2020AിψៀభηφΤϞιάȢ
(Yellow
DG2020A ിᚸѦȼжȦўыѥТѫ
opyright © Tektronix, Inc. All rights reserved.
ektronix products are covered by U.S. and foreign patents, issued and pending.
nformation in this publication supercedes that in all previously published material.
pecifications and price change privileges reserved.
ektronix Japan, Ltd., 5–9–31 Kitashinagawa, Shinagawa–ku, T okyo 141–0001 Japan
ektronix, Inc., P.O. Box 500, Beaverton,, OR 97070
EKTRONIX and TEK are registered trademarks of Tektronix, Inc.
irst Printing: October 2002
Tektronix 070-A656-50