Tektronix Option 1R Field Install Instructions
Instructions
Rackmount (Option 1R)
RSA6100A Series
071-1871-00
Warning
The servicing instructions are for use by qualified
personnel only. To avoid personal injury, do not
perform any servicing unless you are qualified to
do so. Refer to all safety summaries prior to
performing service.
www.tektronix.com
*P071187100*
071187100
Copyright © Tektronix. All rights reserved. Licensed software products are owned by Tektronix or its subsidiaries or
suppliers, and are protected by national copyright laws and international treaty provisions.
Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication supercedes
that in all previously published material. Specifications and price change privileges reserved.
TEKTRONIX and TEK are registered tradem arks of Tektronix, Inc.
Contacting Tektronix
Tektronix, Inc.
14200 SW Karl Braun Drive
P.O. Box 500
Beaverton, OR 97077
USA
For product information, sales, service, and technical support:
H In North America, call 1-800-833-9200.
H Worldwide, visit www.tektronix.com to find contacts in your area.
Table of Contents
Service Safety Summary 1..........................................
Kit Description 3............................................
Products 3.......................................................
Kit Parts List 3....................................................
Clearance Requirements 5...........................................
Installation Instructions 7....................................
Minimum Tool and Equipment List 7..................................
Remove 9........................................................
Install 12.........................................................
Rackmount the Rack-Adapted Instrument 14.............................
RSA6100A Series Rackmount (Option 1R)
i
Table of Contents
List of Figures
Figure 1: Instrument cooling 4................................
Figure 2: Instrument with Rack Adapter Installed 6..............
Figure 3: Rackmount kit parts 8...............................
Figure 4: Strip instrument for conversion 10......................
Figure 5: Rackmount panel preassembly 11......................
Figure 6: Right inside track identification 12.....................
Figure 7: Installation of rackmount assemblies 13.................
Figure 8: Assembly of slide-out track assemblies 16................
Figure 9: Vertical clearances for rack installation
(left-front rail shown) 17...................................
Figure 10: Installation of slide-out track assemblies in rack
(top view) 18.............................................
List of Tables
T able 1: Warranted characteristics 5...........................
Table 2: Tools required for rackmount installation 7.............
ii
RSA6100A Series Rackmount (Option 1R)
Service Safety Summary
Only qualified personnel should perform service procedures. Read this Service
Safety Summary and the General Safety Summary in the product service manual
or the instruction manual.
Do Not Service Alone. Do not perform internal service or adjustments of this
product unless another person capable of rendering first aid and resuscitation is
present.
To prevent the instrument and rack from falling onto the operator, two or more
installers should install the instrument into the rack cabinet. After completing the
installation procedure, the installers should verify that the instrument and rack
cabinet will not tip forward while the instrument is in the extended position.
Disconnect Power. To avoid electric shock, switch off the instrument power, then
disconnect the power cord from the mains power.
Use Care When Servicing With Power On. Dangerous voltages or currents may
exist in this product. Disconnect power, remove battery (if applicable), and
disconnect test leads before removing protective panels, soldering, or replacing
components.
To avoid electric shock, do not touch exposed connections.
RSA6100A Series Rackmount (Option 1R)
1
Service Safety Summary
2
RSA6100A Series Rackmount (Option 1R)
Kit Description
Products
Kit Parts List
This kit describes the installation of Option 1R (rackmount kit) on your
RSA6100A Series Real-Time Spectrum Analyzer. The rackmount kit is a
collection of parts that, once installed, configures the instrument for mounting
into a standard 19-inch equipment rack.
RSA6100A Series AllSerialNumbers
Figure 3 on
page 8
-- -- -- -- -- -- -- -- -- 1ea 016-1962-XX Rackmount Kit:RSA6100A Series, consisting of
-- -- -- -- -- -- -- -- -- 1 e a 071-1871-XX Technical manual: Instructions, Rackmount,
3-1 1 ea 441-2407-XX Rackmount bracket set consisting of: left and
Quantity Part number Description
the following:
RSA6100A Series
right sides, aluminum, silver gray
3-2 1 ea 351-0313-01 Guide rack, consisting of: left and right side
3-3 4 ea NS Screw, mach: 10-32, pan head, 0.375 in l,
phillips
3-3 7 ea NS Nut, locking washer: 10-32 assembly
3-3 14 ea NS Screw, mach: 10-32, Truss head, 0.5 in l, phillips
3-3 4 ea NS Screw, mach: M6 x 20 ovl head, phillips
3-3 4 ea NS Screw, mach: M5 x 20 ovl head, phillips
3-3 8 ea NS Screw, mach: 10-32 x 0.75 ovl head, phillips
3-3 4 ea NS Screw, mach: 12-32 x 0.75 ovl head, phillips
3-3 9 ea NS Washer: flat, nylon
3-4 1 ea 351-0241-XX Slide, drawer, extenders: Sliders
3-4 1 ea NS Rack: Mounting screws, nut blocks
3-5 2 ea 367-0525-XX Handle: Bracket, aluminum, silver gray
3-6 4ea 212-0577-XX Screw, mach: 10-32, Truss head, 0.625 in,
PozidrivR
NS - Not Saleable
RSA6100A Series Rackmount (Option 1R)
3
Kit Description
Warranted Characteristics
Cool air in
When the instrument is installed as instructed in this document, the rackmounted
instrument meets all warranted requirements listed in the instrument specification except for those listed in Environmental Requirements on page 5.Useof
mounting methods other than those described in these instructions can cause the
instrument to not meet warranted requirements.
See the RSA6100A Series Specifications and Performance Verification Technical
Reference (Tektronix part number 071-1915-XX) for tables of the warranted
characteristics.
Cooling air enters from the left side as shown in Figure 1. You assume the
responsibility to provide adequate cool air to meet the ambient temperature
requirements listed in Table 1.
Hot air out
Measure
input air
temperature
Figure 1: instrument cooling
4
RSA6100A Series Rackmount (Option 1R)
Loading...