Tektronix MTS4UP, MTS4SA, MTS430, MTS400 User Manual

MTS400 Series MPEG Test Systems Getting Started Manual

071-1505-06

This document applies to version 1.4 and above.

Warning

The servicing instructions are for use by qualified personnel only. To avoid personal injury, do not perform any servicing unless you are qualified to do so. Refer to all safety summaries prior to performing service.

www.tektronix.com

Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication supersedes that in all previously published material. Specifications and price change privileges reserved.

TEKTRONIX and TEK are registered trademarks of Tektronix, Inc.

Contacting Tektronix

Tektronix, Inc. 14200 SW Karl Braun Drive or P.O. Box 500 Beaverton, OR 97077 USA

For product information, sales, service, and technical support:

■ In North America, call 1-800-833-9200.

■ Worldwide, visit www.tektronix.com to find contacts in your area.

Warranty 2

Tektronix warrants that this product will be free from defects in materials and workmanship for a period of one (1) year from the date of shipment. If any such product proves defective during this warranty period, Tektronix, at its option, either will repair the defective product without charge for parts and labor, or will provide a replacement in exchange for the defective product. Parts, modules and replacement products used by Tektronix for warranty work may be new or reconditioned to like new performance. All replaced parts, modules and products become the property of Tektronix.

In order to obtain service under this warranty, Customer must notify Tektronix of the defect before the expiration of the warranty period and make suitable arrangements for the performance of service. Customer shall be responsible for packaging and shipping the defective product to the service center designated by Tektronix, with shipping charges prepaid. Tektronix shall pay for the return of the product to Customer if the shipment is to a location within the country in which the Tektronix service center is located. Customer shall be responsible for paying all shipping charges, duties, taxes, and any other charges for products returned to any other locations.

This warranty shall not apply to any defect, failure or damage caused by improper use or improper or inadequate maintenance and care. Tektronix shall not be obligated to furnish service under this warranty a) to repair damage resulting from attempts by personnel other than Tektronix representatives to install, repair or service the product; b) to repair damage resulting from improper use or connection to incompatible equipment; c) to repair any damage or malfunction caused by the use of non-Tektronix supplies; or d) to service a product that has been modified or integrated with other products when the effect of such modification or integration increases the time or difficulty of servicing the product.

THIS WARRANTY IS GIVEN BY TEKTRONIX WITH RESPECT TO THE PRODUCT IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED. TEKTRONIX AND ITS VENDORS DISCLAIM ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. TEKTRONIX' RESPONSIBILITY TO REPAIR OR REPLACE DEFECTIVE PRODUCTS IS THE SOLE AND EXCLUSIVE REMEDY PROVIDED TO THE CUSTOMER FOR BREACH OF THIS WARRANTY. TEKTRONIX AND ITS VENDORS WILL NOT BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES IRRESPECTIVE OF WHETHER TEKTRONIX OR THE VENDOR HAS ADVANCE NOTICE OF THE POSSIBILITY OF SUCH DAMAGES.

Warranty 9(b)

Tektronix warrants that the media on which this software product is furnished and the encoding of the programs on the media will be free from defects in materials and workmanship for a period of three (3) months from the date of shipment. If any such medium or encoding proves defective during the warranty period, Tektronix will provide a replacement in exchange for the defective medium. Except as to the media on which this software product is furnished, this software product is provided "as is" without warranty of any kind, either express or implied. Tektronix does not warrant that the functions contained in this software product will meet Customer's requirements or that the operation of the programs will be uninterrupted or error-free.

In order to obtain service under this warranty, Customer must notify Tektronix of the defect before the expiration of the warranty period. If Tektronix is unable to provide a replacement that is free from defects in materials and workmanship within a reasonable time thereafter, Customer may terminate the license for this software product and return this software product and any associated materials for credit or refund.

THIS WARRANTY IS GIVEN BY TEKTRONIX WITH RESPECT TO THE PRODUCT IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED. TEKTRONIX AND ITS VENDORS DISCLAIM ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. TEKTRONIX' RESPONSIBILITY TO REPLACE DEFECTIVE MEDIA OR REFUND CUSTOMER'S PAYMENT IS THE SOLE AND EXCLUSIVE REMEDY PROVIDED TO THE CUSTOMER FOR BREACH OF THIS WARRANTY. TEKTRONIX AND ITS VENDORS WILL NOT BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES IRRESPECTIVE OF WHETHER TEKTRONIX OR THE VENDOR HAS ADVANCE NOTICE OF THE POSSIBILITY OF SUCH DAMAGES.

General Safety Summary ...................................................................................... v

Service Safety Summary...................................................................................... vii

Environmental Considerations ............................................................................ ix

Preface.................................................................................................................... xi

Related Material..................................................................................................... xii

Manual Conventions........................................................................................... xiii

Getting Started

Product Description ............................................................................................ 1-1

Features and Benefits............................................................................................ 1-2

Hardware Features ................................................................................................ 1-3

Options.................................................................................................................. 1-4

Accessories ......................................................................................................... 1-12

Software Protection............................................................................................. 1-13

MTS400 Series system Installation.................................................................. 1-15

Unpacking the MTS400 Series system ............................................................... 1-15

Standard Test System Interconnections .............................................................. 1-15

Powering On and Off .......................................................................................... 1-22

Network Installation............................................................................................ 1-23

Duplex Operation................................................................................................ 1-23

MTS4SA Stand-Alone System Installation..................................................... 1-27

Installation........................................................................................................... 1-29

VLC Media Player Installation ........................................................................... 1-37

Starting an Application ....................................................................................1-39

Starting the TSCA............................................................................................... 1-40

Setting the Interpretation Standard ..................................................................... 1-42

Off-Line Analysis ...............................................................................................1-44

Real-Time Analysis ............................................................................................ 1-46

Stream Analysis Results...................................................................................... 1-47

Operating Basics

Operating Basics .................................................................................................2-1

Software Applications........................................................................................... 2-1

MTS400 Series MPEG Test Systems Getting Started Manual i

Table of Contents

Appendices

Appendix A: Cleaning and Maintenance ......................................................... A-1

General Care......................................................................................................... A-1

Preventive Maintenance .......................................................................................A-1

In Case of Problems ............................................................................................. A-3

Repackaging for Shipment................................................................................... A-4

Appendix B: MTS400 Series system Recovery................................................ B-1

Overview .............................................................................................................. B-1

Restore Operating System.................................................................................... B-3

Install the MTS400 Series system Applications................................................... B-8

Reformat the SCSI Drives.................................................................................... B-9

Appendix C: Network Troubleshooting........................................................... C-1

Basic Requirements.............................................................................................. C-1

IP Parameters ....................................................................................................... C-2

Common Troubleshooting Procedures................................................................. C-5

Sources of Network Information.......................................................................... C-8

Glossary

Index

ii MTS400 Series MPEG Test Systems Getting Started Manual

Table of Contents

List of Figures

Figure 1-1: MTS400 Series system front panel..................................................................1-1

Figure 1-2: MTS400 Series system rear-panel connectors...............................................1-16

Figure 1-3: SFP module ................................................................................................... 1-20

Figure 1-4: TSCA - File Open..........................................................................................1-47

Figure B-1: SCSI drives automatically recognized........................................................... B-4

Figure B-2: Computer Management - SCSI drives, foreign.............................................. B-5

Figure B-3: Select Import Foreign Disks… ...................................................................... B-5

Figure B-4: Import Foreign Disks dialog box................................................................... B-6

Figure B-5: Foreign Disk Volumes dialog box ................................................................. B-6

Figure B-6: SCSI drives manually recognized.................................................................. B-7

Figure B-7: MTS400 Installation – Setup Type................................................................ B-8

Figure C-1: Incorrect IP address ....................................................................................... C-2

Figure C-2: Incorrect subnet mask.................................................................................... C-3

Figure C-3: Incorrect default gateway IP address............................................................. C-4

Figure C-4: Ping.exe command window........................................................................... C-6

Figure C-5: Tracert.exe command window....................................................................... C-7

Figure C-6: Command prompt with nslookup results....................................................... C-8

MTS400 Series MPEG Test Systems Getting Started Manual iii

Table of Contents

List of Tables

Table 1-1: MTS400 System options .................................................................................1-4

Table 1-2: MTS430 System options .................................................................................1-7

Table 1-3: MTS4SA Stand-alone System options .............................................................1-9

Table 1-4: MTS4UP options ........................................................................................... 1-10

Table 1-5: Standard accessories for the MTS400 Series system ..................................... 1-12

Table 1-6: Standard accessories for the MTS4SA Stand-Alone System .........................1-13

Table 1-7: Rear-panel connectors .................................................................................... 1-17

Table 1-8: Electrical operating requirements................................................................... 1-21

Table 1-9: MTS400 Series system Start menu................................................................. 1-39

Table 2-1: MTS400 / MTS430 / MTS4SA / MTS4UP installed applications .................. 2-1

Table A-1: Troubleshooting power-on failures................................................................. A-3

Table B-1: MTS400 Series system Recovery Media........................................................ B-1

iv MTS400 Series MPEG Test Systems Getting Started Manual

General Safety Summary

Review the following safety precautions to avoid injury and prevent damage to this product or any products connected to it.

To avoid potential hazards, use this product only as specified.

Only qualified personnel should perform service procedures.

While using this product, you may need to access other parts of the system. Read the General Safety Summary in other system manuals for warnings and cautions related to operating the system.

To Avoid Fire or Personal Injury

Use Proper Power Cord. Use only the power cord specified for this product and

certified for the country of use.

Connect and Disconnect Properly. Do not connect or disconnect probes or test leads while they are connected to a voltage source.

Ground the Product. This product is grounded through the grounding conductor of the mainframe power cord. To avoid electric shock, the grounding conductor must be connected to earth ground. Before making connections to the input or output terminals of the product, ensure that the product is properly grounded.

Observe All Terminal Ratings. To avoid fire or shock hazard, observe all ratings and markings on the product. Consult the manual for further ratings information before making connections to the product.

Do not apply a potential to any terminal, including the common terminal, that exceeds the maximum rating of that terminal

Powering Off. The power cord provides Mains disconnect.

Replace Batteries Properly. Replace batteries with the same type and rating.

Do Not Operate Without Covers. Do not operate this product with covers or panels

removed.

Use Proper Fuse. Use only the fuse type and rating specified for this product.

Avoid Exposed Circuitry. Do not touch exposed connections and components when

power is present.

MTS400 Series MPEG Test Systems Getting Started Manual v

General Safety Summary

Wear Eye Protection. Wear eye protection if exposure to high-intensity rays or laser radiation exists.

Do Not Operate With Suspected Failures. If you suspect there is damage to this product, have it inspected by qualified service personnel.

Do Not Operate in Wet/Damp Conditions.

Do Not Operate in an Explosive Atmosphere.

Keep Product Surfaces Clean and Dry.

Provide Proper Ventilation. Refer to the manual’s installation instructions for

details on installing the product so it has proper ventilation.

Symbols and Terms

Terms in this Manual. These terms may appear in this manual:

WARNING. Warning statements identify conditions or practices that could result in

injury or loss of life.

CAUTION. Caution statements identify conditions or practices that could result in damage to this product or other property.

Terms on the Product. These terms may appear on the product:

DANGER indicates an injury hazard immediately accessible as you read the marking.

WARNING indicates an injury hazard not immediately accessible as you read the marking.

CAUTION indicates a hazard to property including the product.

Symbols on the Product. The following symbols may appear on the product:

CAUTION

Refer to Manual

WARNING

High Voltage

Protective Ground

(Earth) Terminal

Standby

vi MTS400 Series MPEG Test Systems Getting Started Manual

Service Safety Summary

Only qualified personnel should perform service procedures. Read this Service Safety Summary and the General Safety Summary before performing any service

procedures.

Do Not Service Alone. Do not perform internal service or adjustments of this product unless another person capable of rendering first aid and resuscitation is present.

Disconnect Power. To avoid electric shock, switch off the instrument power, then disconnect the power cord from the mains power.

Use Care When Servicing With Power On. Dangerous voltages or currents may exist in this product. Disconnect power, remove battery (if applicable), and disconnect test leads before removing protective panels, soldering, or replacing components.

To avoid electric shock, do not touch exposed connections.

MTS400 Series MPEG Test Systems Getting Started Manual vii

Service Safety Summary

viii MTS400 Series MPEG Test Systems Getting Started Manual

Environmental Considerations

This section provides information about the environmental impact of the product.

Product End-of-Life Handling

Observe the following guidelines when recycling an instrument or component:

Equipment Recycling. Production of this equipment required the extraction and use

of natural resources. The equipment may contain substances that could be harmful to the environment or human health if improperly handled at the product's end of life. In order to avoid release of such substances into the environment and to reduce the use of natural resources, we encourage you to recycle this product in an appropriate system that will ensure that most of the materials are reused or recycled appropriately.

The symbol shown to the left indicates that this product complies with the European Union's requirements according to Directive 2002/96/EC on waste electrical and electronic equipment (WEEE). For information about recycling options, check the Support/Service section of the Tektronix Web site (www.tektronix.com).

Mercury Notification. This product uses an LCD backlight lamp that contains

mercury. Disposal may be regulated due to environmental considerations. Please contact your local authorities or, within the United States, the Electronics Industries Alliance (www.eiae.org) for disposal or recycling information.

Restriction of Hazardous Substances

This product has been classified as Monitoring and Control equipment, and is outside the scope of the 2002/95/EC RoHS Directive.

MTS400 Series MPEG Test Systems Getting Started Manual ix

Environmental Considerations

x MTS400 Series MPEG Test Systems Getting Started Manual

Preface

This manual describes the functions and use of the Tektronix MTS400 Series MPEG Test Systems. The following naming conventions are used in this manual:

 MTS400 Series system – for information that applies to the MTS400, the

MTS430, and the MTS4SA

 MTS400 system – for information that applies to only the MTS400

 MTS430 system - for information that applies to only the MTS430

 MTS4SA Stand-alone system - for information that applies to only the

MTS4SA

 MTX100B/RTX100B/RTX130B - for information that applies to only the

MTX100B MPEG Recorder and Player, the RTX100B ISDB-T RF Signal Generator, and the RTX130B QAM and VSB RF Signal Generator.

The manual is organized into the following sections:

 Getting Started

Description and overview of the MTS400 Series system, plus instructions for installing the stand-alone version of the MTS400 Series system.

 Operating Basics

A brief introduction to the software applications installed in the MTS400 Series system. For detailed operating information about the applications, refer to the MTS400 Series MPEG Test Systems User Manual.

 Appendices

 Appendix A: Cleaning and Maintenance.

 Appendix B: System Recovery. Explains how to reinstall the operating

system and application software if you encounter problems with the software.

 Appendix C: Network Troubleshooting. A high-level overview of

diagnosing and troubleshooting network connection problems.

 Glossary

 Index

MTS400 Series MPEG Test Systems Getting Started Manual xi

Preface

Related Material

The following table lists the other manuals available for the MTS400 Series system.

Manual Conventions

Naming conventions for the interface elements are based on standard Windows naming conventions.

Naming conventions for MPEG-2, ATSC, and DVB structures follow the conventions established by the standards organizations.

The following formatting conventions apply to this manual:

 Bold text refers to specific interface elements that you are instructed to select,

click, or clear. Example: Select Settings from the Configuration menu.

 Mono-spaced text can indicate the following:

 Text you enter from a keyboard

Example: Enter the network identity (http://TSMonitor01)

 Characters you push on your keyboard

Example: Push

CTRL+C to copy the selected text.

 Paths to components on your hard drive

Example: The program files are installed at the following location: C:\Program Files\Tektronix\

MTS400 Series MPEG Test Systems Getting Started Manual xiii

Preface

xiv MTS400 Series MPEG Test Systems Getting Started Manual

Getting Started

Product Description

The MTS400 Series MPEG Test Systems provide a comprehensive and integrated suite of real-time and deferred (offline) analysis tools. The tools include TS (transport stream) compliance, buffer, PES, MPEG2, and MPEG4 video and audio elementary stream analyzers. Also included are an editor and a multiplexer to create stream content, and test and error-stressing streams.

Standards compliance is ensured though built-in customizable scripting, which supports a broad range of ratified and evolving DTV standards. New standards and proprietary tables can easily be implemented by loading Tektronix supplied updates, or creating your own custom scripts.

The MTS400 series instruments have a large LCD display with a powerful

2.8 GHz processor with support for multiple physical layer interfaces such as ASI, SPI, SMPTE310M, RF, including QAM (annex B), COFDM DVB-T, QPSK/8PSK, and 8VSB, and IP (10/100 BaseT and Gigabit Ethernet).

On/Stby switch

Figure 1-1: MTS400 Series system front panel

There are three variants of the MTS400 Series MPEG Test System: the MTS400 system, the MTS430 system, and the MTS4SA Stand-alone system.

 The MTS400 system includes SPI, ASI and SMPTE310M interfaces, real-

time transport stream analysis and transport stream play and record.

MTS400 Series MPEG Test Systems Getting Started Manual 1-1

Product Description

Features and Benefits

 The MTS430 system includes SPI, ASI and SMPTE310M and 10/100 IP

interfaces, real-time transport stream analysis, play and record, deferred time transport stream, packetized elementary stream, and buffer analysis and multiplexing.

 The MTS4SA Stand-alone system allows the deferred analysis and testing

components to be installed on a personal computer.

See Options, starting on page 1-4, for the details of each system.

The MTS400 Series software will also run on the MTX100B, RTX100B, and RTX130B. Real-time analysis requires that the MTX100B Option 7 is available.

The system provides the following features:

 The CaptureVu™ feature captures and analyzes system events in real time

and deferred time to debug the intermittent and complex problems that traditional analyzers miss.

 Real-time video over IP analysis and recording for broadband and video on

demand applications is supported using the MTS430 system’s built-in Gigabit Ethernet port. (This feature is also available separately as a stand-alone application to run on your PC with a standard 10/100 or Gigabit Ethernet network interface card).

 High performance analysis engine to analyze transport streams up to

400 Mbps (in deferred time). This greatly reduces the amount of time taken by the deferred time software to analyze large and complex transport stream files. This capability also protects your investment in the MTS400 because the deployment of new services, such as VOD and HD, will require greater aggregated bandwidth and data rates than are available in other products today.

 The innovative “program centric” user interface brings expert power to the

novice user by helping locate network and service related problems fast.

 Broadest and deepest range of analysis of legacy and next generation

compressed standards including MPEG-2, MPEG-4, H.264, and SMPTE VC-1. Mobile video standards included are 3GPP and DVB-H.

 Support for a full and wide range of current world-wide DTV standards.

Rapid implementation and analysis of new and proprietary DTV standards is enabled by a flexible user-definable scripting language.

 Modular design allows you to purchase only the performance that you require

today and makes it easy to upgrade for changing needs.

1-2 MTS400 Series MPEG Test Systems Getting Started Manual

Product Description

Hardware Features

The basic MTS400 Series instrument consists of:

 One, 80 GB IDE hard drive

(disk space, operating system and software applications)

 Two, 72 GB SCSI hard drives (disk space, MPEG file storage)

 2.8 GHz P4 processor

 1 GB RAM

 DVD drive (-R/-RW,+R/+RW)

 3.5 inch floppy disk drive (1.44 MB high-density)

 An LCD display, 1024 x 768, 10.4 inch

 Operating System: Windows XP Pro

 Ethernet connectors

(one 10/100-base T connector and one 10/100/1000-base T connector)

 USB port

 A170 card, LVDS/ASI/SMPTE310 interface

 A12 card, main MPEG input/output

MTS400 Series MPEG Test Systems Getting Started Manual 1-3

Product Description

Options

MTS400 System Options

A range of options is available for the MTS400 Series MPEG Test Systems. The option descriptions begin on the following pages:

 MTS400 System Options (page 1-4)

 MTS430 System Options (page 1-7)

 MTS4SA Stand-alone System (page 1-9)

 MTS4UP Options (page 1-10)

The MTS400 platform includes SPI, ASI, SMPTE310M interfaces, real time TS analysis, and TS play and record.

MTS400 System Basic Application Set.

 Transport Stream Compliance Analyzer (TSCA) - Real Time

 Tracer

 Player / Recorder

 TS Editor

 TS Cutter

 Script Pad

Table 1-1: MTS400 System options (cont.)

Item Opt Description

MTS400

MTS400 Series MPEG Test System IPE Add 10/100BaseT Video over IP electrical interface to MTS400 MX Add Deferred Time Multiplexer to MTS400 ES Add ES Analyzer to MTS400 BA Add Buffer Analyzer to MTS400 PA Add PES to MTS400 DB Add Carousel Analyzer to MTS400 CG Add Carousel Generator to MTS400 DBCG Add Carousel Analyzer and Carousel Generator to MTS400

1-4 MTS400 Series MPEG Test Systems Getting Started Manual

Product Description

Table 1-1: MTS400 System options (cont.)

Item Opt Description

MTS400

L99 Electronic User Documentation (No printed manuals)

TSCA Add Transport Stream Compliance Analyzer to MTS400 TSCL Add Transport Stream Compliance Analyzer Lite (file size limited) to

MTS400

GBE Add GbE (GigE) Video over IP interface to MTS400, includes IP analysis

software

CU 1000BASE-T electrical port with RJ45 connector for MTS400 gigabit

Ethernet interface

LX 1000BASE-LX long wavelength optical port with LC connector for

MTS400 gigabit Ethernet interface (single mode 1310 NM)

SX 1000BASE-SX short wavelength optical port with LC connector for

MTS400 gigabit Ethernet interface (multi mode 850 NM)

ZX 1000BASE-ZX long wavelength optical port with LC connector for

MTS400 gigabit Ethernet interface (single mode 1550 NM) CF Add COFDM DVB-T interface to MTS400 EP Add QPSK/8PSK interface to MTS400 QB2 Add QAM (Annex B) interface to MTS400 VS Add 8VSB interface to MTS400 R3 Repair Service 3 years R5 Repair service 5 years L0 English Documentation L5 Japanese Documentation

A0 North American Power A1 Universal Euro Power A2 United Kingdom Power A3 Australia Power A4 240 V North America Power A5 Switzerland Power A6 Japan Power A10 China Power A11 India Power A99 No Power cord or AC adapter

Additional MTS4EA Options (Compressed Video ES Analyzer) (at order time)

MTS400

4EAB Base software with video standard package including: MPEG-4 Simple

Profile, H.263+, H.263, H.261, CD and Manual M4SP MPEG-4 Advanced Simple Profile (Levels 0 - 5) M2ML MPEG-2 Main Profile Main Level

MTS400 Series MPEG Test Systems Getting Started Manual 1-5

Product Description

Table 1-1: MTS400 System options (cont.)

Item Opt Description

M2HL MPEG-2 Main Profile High Level & High Level 1440 (High Definition) AVCE H.264/AVC Baseline and Extended Profiles (Levels 1 - 5) AVCH H.264/AVC High Profile with FREXT (10 bit, 4:22:2, 4:4:4) AVCM H.264/AVC Main Profile (Levels 1 - 5) AVDM Audio visual delay measurement. Requires option 4EAB SWSE First 12 Months’ Software Subscription on the MTS4EA software and its

options loaded on the MTS400, when purchased with a new MTS400.

(Does not cover the MTS400 software.) VC-1 VC-1 (all profiles, all levels) and Windows Media V9 (ASF) AUD Audio (including AAC, HE AAC, AC-3)

1-6 MTS400 Series MPEG Test Systems Getting Started Manual

Product Description

MTS430 System Options

The MTS430 platform includes SPI, ASI, SMPTE310M and 10/100 IP interfaces, real time TS analysis, play and record, deferred time TS, PES and Buffer Analysis, and Multiplexing.

MTS430 System Basic Application Set.

 Transport Stream Compliance Analyzer (TSCA) - Real Time / Deferred

 Packetized Elementary Stream (PES) Analyzer

 Transport Stream – System Target Decoder (T-STD) Buffer Analyzer

 Tracer

 Player / Recorder

 TS Editor

 Multiplexer (+ Make Seamless Wizard)

 TS Cutter

 Script Pad

Table 1-2: MTS430 System options (cont.)

Item Opt Description

MTS430

MTS430 MPEG Test System

ES Add ES Analyzer to MTS430

DB Add Carousel Analyzer to MTS430

CG Add Carousel Generator to MTS430

DBCG Add Carousel Analyzer and Carousel Generator to MTS430

GBE Add GbE (GigE) Video over IP interface to MTS400, includes IP analysis

software

CU 1000BASE-T electrical port with RJ45 connector for MTS400 gigabit

Ethernet interface

LX 1000BASE-LX long wavelength optical port with LC connector for

MTS400 gigabit Ethernet interface (single mode 1310 NM)

SX 1000BASE-SX short wavelength optical port with LC connector for

MTS400 gigabit Ethernet interface (multi mode 850 NM)

ZX 1000BASE-ZX long wavelength optical port with LC connector for

MTS400 gigabit Ethernet interface (single mode 1550 NM)

SWSM First 12 months MTS400 software subscription (Does not include

subscription to MTS4EA)

MTS400 Series MPEG Test Systems Getting Started Manual 1-7

Product Description

Table 1-2: MTS430 System options (cont.)

Item Opt Description

MTS430

A11 India Power

A99 No Power cord or AC adapter

CF Add COFDM DVB-T interface to MTS430 EP Add QPSK/8PSK interface to MTS430 QB2 Add QAM (Annex B) interface to MTS430 VS Add 8VSB interface to MTS430

R3 Repair Service 3 years

R5 Repair service 5 years

L0 English Documentation

L5 Japanese Documentation

L99 Electronic User Documentation (No printed manuals)

A0 North American Power

A1 Universal Euro Power

A2 United Kingdom Power

A3 Australia Power

A4 240V North America Power

A5 Switzerland Power

A6 Japan Power

A10 China Power

Additional MTS4EA Options (Compressed Video ES Analyzer) (at order time)

MTS430

4EAB Base software with video standard package including: MPEG-4 Simple

Profile, H.263+, H.263, H.261, CD and Manual

M4SP MPEG-4 Advanced Simple Profile (Levels 0 – 5)

M2ML MPEG-2 Main Profile Main Level

M2HL MPEG-2 Main Profile High Level & High Level 1440 (High Definition)

AVCE H.264/AVC Baseline and Extended Profiles (Levels 1 – 5)

AVCM H.264/AVC Main Profile (Levels 1 – 5)

SWSE First 12 Months Software Subscription on the MTS4EA software and its

options loaded on the MTS430, when purchased with a new MTS430. (Does not cover the MTS430 software.)

VC-1 VC-1 (all profiles, all levels) and Windows Media V9 (ASF)

AUD Audio (including AAC, HE AAC, AC-3)

1-8 MTS400 Series MPEG Test Systems Getting Started Manual

Product Description

MTS4SA Stand-alone System

This product provides deferred analysis software for stand-alone operation.

MTS4SA Stand-alone System Basic Application Set

 Tracer

 Player

 TS Editor

 TS Cutter

 Script Pad

Table 1-3: MTS4SA Stand-alone System options

Item Opt Description

MTS4SA

Stand Alone Deferred Time Software Package

USB USB Security software key supplied with Stand

Alone Software Package

PPD Parallel Port Security software supplied with Stand

Alone Software Package

MX Security software key to add Deferred Time Multiplexer to MTS4SA

ES Security software key to add ES Analyzer to MTS4SA

PB Security software key to add PES & Buffer Analyzer to MTS4SA

BA Security software key to add Buffer Analyzer to MTS4SA

PA Security software key to add PES to MTS4SA

DB Security software key to add Carousel Analyzer to MTS4SA

CG Security software key to add Carousel Generator to MTS4SA

DBCG Security software key to add Carousel Analyzer and Carousel Generator

to MTS4SA

TSCA Security software key to add Deferred Time Transport Stream

Compliance Analyzer to MTS4SA

TSCB Security software key to add real time and deferred time Transport

Stream Compliance Analyzer to MTS4SA for IP interface only

TSCL Security software key to add Deferred Time Transport Stream

Compliance Analyzer Lite (file size limited) to MTS4SA

TSCR Security software key to add Real Time Transport Stream Compliance

Analyzer to MTS4SA for IP interface only

L0 English Documentation

L5 Japanese Documentation

L99 Electronic User Documentation (No printed manuals)

Upgrade requires either USB or PPD (not both).

MTS400 Series MPEG Test Systems Getting Started Manual 1-9

Product Description

MTS4UP Options

The MTS4UP options allow you to upgrade to add options after ordering an MTS400, MTS430, or MTS4SA.

Table 1-4: MTS4UP options (cont.)

Item Opt Description

MTS4UP

MTS4 Series Field Upgrade Kit IPE Add 10/100BaseT Video over IP electrical interface to MTS400 MX Add Deferred Time Multiplexer to MTS4 series ES Add ES Analyzer to MTS4 series BA Add Buffer Analyzer to MTS4 series PA Add PES to MTS4 series DB Add Carousel Analyzer to MTS4 series CG Add Carousel Generator to MTS4 series DBCG Add Carousel Analyzer and Carousel Generator to MTS4 series TSCA Add Transport Stream Compliance Analyzer to MTS4 series TSCB Upgrade to add real time and deferred time transport stream

compliance analyzer to MTS4SA for IP interface only

TSCL Add Transport Stream Compliance Analyzer Lite (file size limited) to

MTS4 series

TSCP Upgrade to add Transport Stream Compliance Analyzer, PES Analyzer

and Buffer Analyzer to MTS4 series

TSCR Add Real Time Transport Stream Compliance Analyzer to MTS4SA for

IP interface only

UPG Upgrade to latest version of MTS4 series base software and installed

options. Includes CD and Manual (excluding MTS4EA). Requires

MTS4UP Opt. SWS1. IF Tektronix installs MTS4UP IFC Tektronix installs MTS4UP with calibration GBE Add GbE (GigE) Video over IP interface to MTS400, includes IP analysis

software CU 1000BASE-T electrical port with RJ45 connector for MTS400 gigabit

Ethernet interface LX 1000BASE-LX long wavelength optical port with LC connector for

MTS400 gigabit Ethernet interface (single mode 1310 NM) SX 1000BASE-SX short wavelength optical port with LC connector for

MTS400 gigabit Ethernet interface (multi mode 850 NM) ZX 1000BASE-ZX long wavelength optical port with LC connector for

MTS400 gigabit Ethernet interface (single mode 1550 NM) CF Add COFDM DVB-T interface to MTS400

1-10 MTS400 Series MPEG Test Systems Getting Started Manual

+ 76 hidden pages