Tektronix MTS4KUP ESS, MTS4SA MPEG, MTS4KUP ESE, MTS4KUP GEN, MTS4KUP PQ Instructions Manual
...
xx
MTS4KUP
10GS, ASI, ESE, ESS, GEN, IPTV, LX, PB, PQ, QB2, S2, SX,
VQ, VS, and ZX
ZZZ
MTS4000 Upgrade Kits
Instructions
*P075103600*
075-1036-00
xx
MTS4KUP
10GS, ASI, ESE, ESS, GEN, IPTV, LX, PB, PQ, QB2, S2, SX, VQ,
VS, and ZX
ZZZ
MTS4000 Upgrade Kits
Instructions
www.tektronix.com
075-1036-00
Copyright © Tektronix. All rights reserved. Licensed software products are owned by Tektronix or its subsidiaries
or suppliers, and are protected by national copyright laws and international treaty provisions.
Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication
supersedes that in all previously published material. Specifications and price change privileges reserved.
TEKTRONIX and TEK are registered trademarks of Tektronix, Inc.
Contacting Tektronix
Tektronix, Inc.
14150 SW Karl Braun Drive
P.O. B o x 5 0 0
Beaverto
USA
For product information, sales, service, and technical support:
n, OR 97077
In North America, call 1-800-833-9200.
Worl dwid e, visi t www.tektronix.com to find contacts in your area.
Table of Contents
General Safety Summary ......................................................................................... iv
Service Safety Summary...................................... ................................ .................... vi
Kit description ........................................... .................................. ....................... vii
Kit parts li
Software upgrade instructions.................................... .................................. ............... 5
Hardware upgrade instructions.................................................................................... 7
Optical SFP upgrades ............................................................................................. 17
sts ................... ................................ .................................. ................... 1
MTS4000 Upgrade Kit Instructions i
Table of Contents
List of Figure
Figure 1: IPTV interface card bumper installation ............................................................. 8
Figure 2: QB
Figure 3: Remove rear panel ........... ................................ .................................. ........ 10
Figure 4: CIP cable installation on option IPTV interface card .................. ............................ 12
Figure 5: COM connectors on motherboard............................ ................................ ........ 13
Figure 6: CIP cable installation on option QB2, S2, and VS interface cards . .............................. 14
Figure 7: Sample SFP optical module........................................................................... 17
2, S2, and VS interface cards bumper installation............................................... 8
s
ii MTS4000 Upgrade Kit Instructions
List of Tables
Table 1: Recommended tool list . ................................ .................................. ............... 7
Table 2: Int
erface card slot locations ............................ .................................. ............... 9
Table of Contents
MTS4000 Upgrade Kit Instructions iii
General Safety Summary
General Safet
To Avoid Fi
re or Personal
Injury
ySummary
Review the fo
this product or any products connected to it.
To avoid pot
Only qualified personnel should perform service procedures.
Use proper
certified for the country of use.
Ground th
of the power cord. To avoid electric shock, the grounding conductor must be
connected to earth ground. Before making connections to the input or output
terminals of the product, ensure that the product is properly grounded.
Observe all terminal ratings. To a voi d fire or shock hazard, observe all ratings
and markings on the product. Consult the product manual for further ratings
information before making connections to the product.
The inputs are not rated for connection to mains or Category II, III, or IV circuits.
Do not apply a potential to any terminal, including the common terminal, that
exceeds the maximum rating of that terminal.
llowing safety precautions to avoid injury and prevent damage to
ential hazards, use this product only as specified.
power cord. Use only the power cord specified for this product and
eproduct.This product is grounded through the grounding conductor
Power disconnect. The power cord disconnects the product from the power source.
Donotblockthepowercord;itmustremain accessible to the user at all times.
Do not operate without covers. Do not operate this product with covers or panels
removed.
Do not operate with suspected failures. If you suspect that there is damage to this
product, have it inspected by qualified service personnel.
Avoid exposed circuitry. Do not touch exposed connections and components when
power is present.
Wear eye protection. Wear eye protection if exposure to high-intensity rays or
laser radiation exists.
Do not operate in wet/damp conditions.
Do not operate in an explosive atmosphere.
Keep product surfaces clean and dry.
Provide proper ventilation. Refer to the manual's installation instructions for details
on installing the product so it has proper ventilation.
iv MTS4000 Upgrade K it Instructions
General Safety Summary
TermsinThisManual
Symbols and Terms on the
Product
These terms may
WAR NI NG . Warning statements identify conditions or practices that could result
in injury or loss of life.
CAUTION. Caution statements identify conditions or practices that could result in
damage to this product or other property.
These terms may appear on the product:
DANGER in
the marking.
WARNING
read the marking.
CAUTIO
The following symbol(s) may appear on the product:
appear in this manual:
dicates an injury hazard immediately accessible as you read
indicates an injury hazard not immediately accessible as you
N indicates a hazard to property including the product.
MTS4000 Upgrade Kit Instructions v
Loading...