Tektronix MTM4UP Field Install Instructions
Instructions
MTM4UP
Software Option Upgrades for
MTM400 MPEG Transport Monitor
075-0779-02
Warning
The servicing instructions are for use by qualified
personnel only. To avoid personal injury, do not
perform any servicing unless you are qualified to
do so. Refer to all safety summaries prior to
performing service.
www.tektronix.com
*P075077902*
075077902
Copyright © Tektronix, Inc. All rights reserved. Licensed software products are owned by Tektronix or its suppliers and
are protected by United States copyright laws and international t reaty provisions.
Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication supercedes
that in all previously published material. Specifications and price change privileges reserved.
TEKTRONIX and TEK are registered trademarks of Tektronix, Inc.
Contacting Tektronix
Tektronix, Inc.
14200 SW Ka rl Braun Drive or P.O. Box 500
Beaverton, OR 97077 USA
For product information, sales, service, and technical support:
H In North America, call 1-800-833-9200.
H Worldwide, visit www.tektronix.com to find contacts in your area.
Kit Description
This document provides instructions for the MTM400 Software Option upgrade.
The following upgrades are currently available:
Table 1: MTM400 field upgrade kits (software)
Product Option Description
MTM4UP 01 Field upgrade kit to add Recording Capability
02 Field upgrade kit to add Transport Stream Service Information
Analysis (PSI/SI/PSIP/ARIB structure view and repetition
graphs)
03 Field upgrade kit to add Template Testing With Template
Scheduling (for user defined service plan testing)
04 Field upgrade kit to add PCR Analysis with Graphical Results
views
05 Field upgrade kit to add Bit rate testing including PID groups
and PID variability
06 Field upgrade kit to add Service Logging
Software options are enabled by an Option Key -- a unique string of alphanumeric characters which is applied to the MTM400 via the remote user interface. Each
Option Key can enable one or more options.
BIOS Version Requirement
Verify the BIOS version installed in your MTM400 monitor before you perform
the software installation instructions provided in this kit. You can find the BIOS
version number listed in the Info display of the Device view.
The MTM400 monitor must have BIOS version 2.07 installed before the
instrument will load software version 2.0.7 or above.
MTM4UP Software Option Upgrades Instructions
1
Kit Description
Acquiring the Option Key
The following basic information is shipped with the upgrade kit:
H A document recording the Option Key and the unit to which it can be
H The MTM400 Software Option Upgrade Instructions (075-0779-02) -- this
CAUTION. To avoid losing your options, do not misplace the documentation that
is included with this kit. This contains the option installation key number. If the
battery--backed RAM in the unit is reset, the Option Key will be needed to
reenable your options.
Note that the Serial Number identifies the MTM400 unit. The MAC address is
allocated to the Transport Stream Processor board. If the processor board is
changed, it will have a different MAC address and new Option Keys will need to
be issued.
applied. The unit identity will take the form of the Serial Number and the
MAC (Media Access Control) address (this is unique to each unit).
document.
Option Keys
NOTE. The MAC address is printed on the label on the top of the unit and above
the network port at the rear of the unit.
The Option Key is a string of alphanumeric characters in the form nnnnn-nnnnnnnnnn-nnnnn. Each Option Key is unique; it is generated specifically for one
MTM400 unit using the MAC address and the Serial Number. An Option Key
generated for one MTM400 unit will not work when applied to another
MTM400 unit.
The Option Key is supplied as part of the Upgrade documentation.
The upgrade instructions given in the remainder of this document are common to
all options.
2
MTM4UP Software Option Upgrades Instructions
Loading...