Tektronix MTM400A User manual

Technical Reference

MTM400A MPEG Transport Stream Monitor Test Parameter and Configuration File

071-2497-00

This document applies to firmware versions 3.0 and above.

Warning

The servicing instructions are for use by qualified personnel only. To avoid personal injury, do not perform any servicing unless you are qualified to do so. Refer to all safety summaries prior to performing service.

www.tektronix.com

Copyright © Tektronix. All rights reserved. Licensed software products are owned by Tektronix or its subsidiaries or suppliers, and are protected by national copyright laws and international treaty provisions.

Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication supercedes that in all previously published material. Specifications and price change privileges reserved.

TEKTRONIX and TEK are registered trademarks of Tektronix, Inc.

Contacting Tektronix

Tektronix, Inc. 14200 SW Karl Braun Drive P.O. Box 500 Beaverton, OR 97077 USA

For product information, sales, service, and technical support:

H In North America, call 1-800-833-9200.

H Worldwide, visit www.tektronix.com to find contacts in your area.

Test Parameters

General Safety Summary iii. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Service Safety Summary v. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Preface vii. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Related Material vii. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Manual Conventions viii. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Standard Tests 1−3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

MPEG Tests 1−3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

DVB Tests 1−5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

ATSC Tests 1−9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

ISDB-S Tests 1−12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

ISDB-T Tests 1−15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

ISDB (Partial Reception) 1−21. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

DCII Tests 1−26. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

China Tests 1−28. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Info Tests 1−32. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

RF Tests 1−33. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Event Identity to Test Name 1−35. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Test Name to Event Identity 1−11 9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Parameter Reference 1−137. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

General Parameters 1−137. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Interface Parameters 1−141. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Stream Parameters 1−147. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Template Parameters 1−172. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

PID Parameters 1−179. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

PID Groups Parameters 1−183. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Events Parameters 1−184. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Service Log Parameters 1−186. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Trap Setting Parameters 1−187. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Common Interface Protocol Parameters 1−188. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Example Configuration File 1−188. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Event SNMP Traps 1−189. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Configuration File Structure

Updating 2−2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Defaults 2−5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Example Configuration File 2−6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Glossary

MTM400A Test Parameter and Configuration File Technical Reference

Table of Contents

List of Figures

List of Tables

Figure 1−1: Alarm settings 1−186. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Table 1−1: Test name to event identity 1−11 9. . . . . . . . . . . . . . . . . . . . . . . . . .

Table 1−2: Stream Parameters 1−147. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Table 1−3: PID Parameters 1−179. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Table 1−4: Event SNMP Traps - MPEG 1−189. . . . . . . . . . . . . . . . . . . . . . . . .

Table 1−5: Event SNMP Traps - DVB 1−194. . . . . . . . . . . . . . . . . . . . . . . . . .

Table 1−6: Event SNMP Traps - ATSC 1−201. . . . . . . . . . . . . . . . . . . . . . . . .

Table 1−7: Event SNMP Traps - ISDB-S 1−206. . . . . . . . . . . . . . . . . . . . . . . .

Table 1−8: Event SNMP Traps - ISDB-T 1−212. . . . . . . . . . . . . . . . . . . . . . . .

Table 1−9: Event SNMP Traps - ISDB (Partial Reception) 1−219. . . . . . . . . .

Table 1−10: Event SNMP Traps -DCII 1−226. . . . . . . . . . . . . . . . . . . . . . . . . .

Table 1−11: Event SNMP Traps - China 1−231. . . . . . . . . . . . . . . . . . . . . . . .

Table 1−12: Event SNMP Traps - IP 1−237. . . . . . . . . . . . . . . . . . . . . . . . . . .

Table 2−1: Absolute update − example 2−3. . . . . . . . . . . . . . . . . . . . . . . . . .

Table 2−2: Incremental update − example 2−3. . . . . . . . . . . . . . . . . . . . . . .

MTM400A Test Parameter and Configuration File Technical Reference

General Safety Summary

Review the following safety precautions to avoid injury and prevent damage to this product or any products connected to it.

To avoid potential hazards, use this product only as specified.

Only qualified personnel should perform service procedures.

To Avoid Fire or Personal Injury

Use Proper Power Cord. Use only the power cord specified for this product and

certified for the country of use.

Ground the Product. This product is indirectly grounded through the grounding conductor of the mainframe power cord. To avoid electric shock, the grounding conductor must be connected to earth ground. Before making connections to the input or output terminals of the product, ensure that the product is properly grounded.

Ground Equipment Connected to the Product. Ensure that any equipment connected to this product is grounded and at the same potential.

Observe All Terminal Ratings. To avoid fire or shock hazard, observe all ratings and markings on the product. Consult the product manual for further ratings information before making connections to the product.

Do Not Operate Without Covers. Do not operate this product with covers or panels removed.

Use Proper Fuse. Use only the fuse type and rating specified for this product.

Avoid Exposed Circuitry. Do not touch exposed connections and components

when power is present.

Do Not Operate With Suspected Failures. If you suspect there is damage to this product, have it inspected by qualified service personnel.

Do Not Operate in Wet/Damp Conditions.

Do Not Operate in an Explosive Atmosphere.

Keep Product Surfaces Clean and Dry.

Provide Proper Ventilation. Refer to the manual’s installation instructions for

details on installing the product so it has proper ventilation.

MTM400A Test Parameter and Configuration File Technical Reference

iii

General Safety Summary

Symbols and Terms

Terms in this Manual. These terms may appear in this manual:

WARNING. Warning statements identify conditions or practices that could result in injury or loss of life.

CAUTION. Caution statements identify conditions or practices that could result in damage to this product or other property.

Terms on the Product. These terms may appear on the product:

DANGER indicates an injury hazard immediately accessible as you read the marking.

WARNING indicates an injury hazard not immediately accessible as you read the marking.

CAUTION indicates a hazard to property including the product.

Symbols on the Product. The following symbols may appear on the product:

CAUTION

Refer to Manual

Protective Ground

(Earth) Terminal

MTM400A Test Parameter and Configuration File Technical Reference

Service Safety Summary

Only qualified personnel should perform service procedures. Read this Service Safety Summary and the General Safety Summary before performing any service

procedures.

Do Not Service Alone. Do not perform internal service or adjustments of this product unless another person capable of rendering first aid and resuscitation is present.

Disconnect Power. To avoid electric shock, switch off the instrument power, then disconnect the power cord from the mains power.

Use Care When Servicing With Power On. Dangerous voltages or currents may exist in this product. Disconnect power, remove battery (if applicable), and disconnect test leads before removing protective panels, soldering, or replacing components.

To avoid electric shock, do not touch exposed connections.

Use only Tektronix approved components when servicing the unit.

MTM400A Test Parameter and Configuration File Technical Reference

Service Safety Summary

MTM400A Test Parameter and Configuration File Technical Reference

Preface

This manual contains the following information about the MTM400A MPEG Transport Stream Monitor:

H Test Parameters describes the tests performed by the MTM400A monitor; it

also describes the associated parameters. This section provides the following cross-referenced information:

H The Standards Tests section (page 1−3) identifies the tests and event

identities associated with each of the DTV standards; some additional categories are also included.

H Event Identity to Test Name (page 1−35); includes a brief description of

the test, the applicable standards and the associated parameters.

H Test Name to Event Identity (page 1−119) is a cross-reference between

Test Names and Event identities.

H The Parameter Reference subsection (page 1−137) lists all available

parameters.

H Event SNMP Traps tables (page 1−189) lists the SNMP (Simple

Network Management Protocol) traps available for each event.

Model Numbers

Related Material

H Configuration File describes the structure and composition of the

MTM400A configuration file.

This document describes the test parameters and configuration file of the MTM400A and the MTM400 instruments. All references in the test parameters and configuration file on both models are to the MTM400. This ensures that consistency is maintained between the two models.

Additional documentation, such as Read Me files, may be included on the documentation disk.

The MTM400A MPEG Transport Stream Monitor Quick Start User Manual (Tektronix part number: 071-2492-xx) provides installation and high-level operational overviews. This manual is available in English and Japanese languages.

The MTM400A MPEG Transport Stream Monitor Technical Reference (Tektronix part number: 071-2495-xx) provides in-depth operating information.

MTM400A Test Parameter and Configuration File Technical Reference

vii

Preface

The MTM400A MPEG Transport Stream Monitor Programmer Manual (Tektronix part number: 071-2498-xx) specifies the remote control and status monitoring interfaces available to a management application.

The following URLs access the Web sites for the standards organizations listed (the URLs listed were valid at the time of writing):

H MPEG−2 standards (International Organization for Standards)

www.iso.org/

H DVB standards (European Technical Standards Institute)

www.etsi.org/

H ATSC standards (Advanced Television Systems Committee)

www.atsc.org/

H ISDB/ARIB standards (Association of Radio Industries and Businesses)

www.arib.or.jp/english/

H SCTE Society of Cable Television Engineers

www.scte.org

Manual Conventions

Naming conventions for the interface elements are based on standard Windows naming conventions. Naming conventions for MPEG-2, ATSC, and DVB structures follow the conventions derived from the standards documents found at the Web sites listed on page x. In addition, the following formatting conventions apply to this manual:

H Bold text refers to specific interface elements that you are instructed to

select, click, or clear. Example: Select Settings from the Configuration menu.

H Mono-spaced text can indicate the following:

H Text you enter from a keyboard

Example: Enter the network identity (http://TSMonitor01 )

H Characters you press on your keyboard

Example: Press CTRL+C to copy the selected text.

H Paths to components on your hard drive

Example: The program files are installed at the following location:

C:\Program Files\Tektronix\

viii

MTM400A Test Parameter and Configuration File Technical Reference

Test Parameters

Each error state displayed on the user interface is the result of making one or more measurements or tests on the incoming transport stream. The displayed tests are derived from the DVB and ATSC standards. Additional proprietary tests are also included.

Some measurements and tests translate directly to an error state; others are the result of a combination of tests. For many of the tests, you can affect the result by varying parameters that influence the test result, for example, maximum and minimum bit rate values.

This section provides the following cross-referenced information:

H The Standards Tests section (page 1−3) identifies the tests and event

identities associated with each of the DTV standards; some additional categories are also included.

H Event Identity to Test Name (page 1−35) includes a brief description of the

test, the applicable standards and the associated parameters.

H Test Name to Event Identity (Table 1−1, page 1−119) is a cross-reference

between Test Names and Event identities.

H The Parameter Reference subsection (page 1−137) lists all available

parameters.

H Event Traps tables (page 1−189) lists the SNMP (Simple Network Manage-

ment Protocol) traps available for each event.

NOTE. Event identities referred to in this section are relevant to all Tektronix MPEG monitoring products.

MTM400A Test Parameter and Configuration File Technical Reference

1−1

Test Parameters

1−2

MTM400A Test Parameter and Configuration File Technical Reference

Standard Tests

The following sub-sections identify the tests and event identities associated with each of the DTV standards; some additional categories are also included. The sections are as follows:

H MPEG Tests, page 1−3

H DVB Tests, page 1−5

H ATSC Tests, page 1−9

H ISDB-S Tests, page 1−12

H ISDB-T Tests, page 1−15

H ISDB (Partial Reception), page 1−21

H DCII Tests, page 1−26

H China Tests, page 1−28

H Info Tests. page 1−32

MPEG Tests

H RF Tests. page 1−33

MPEG TR 101 290 : Event ID = 37f7

Priority 1 : Event ID = 37f3

1.1 Sync : Event ID = 3011

1.2 Sync Byte : Event ID = 3012

1.3.a PAT : Event ID = 3018

1.3 PAT (Timer) : Event ID = 3100

1.3 PAT (Table ID) : Event ID = 3101

1.3 PAT (Scrambling) : Event ID = 3102

1.4 Continuity : Event ID = 3014 PID Test : 1.4 Continuity : Event ID = 3132

1.5.a PMT : Event ID = 3019

1.5 PMT (Timer) : Event ID = 3103

Ind PMT Err Timer : Event ID = 3160 Program Test : 1.5 PMT (Timer) : Event ID = 3160

1.5 PMT (Scrambling) : Event ID = 3104

1.6 PID : Event ID = 3016 PID Test : 1.6 PID : Event ID = 3017

Priority 2 : Event ID = 37f4

2.1 Transport : Event ID = 3021

2.2 CRC : Event ID = 3022

2.3.a PCR Repetition : Event ID = 3150 PID Test : 2.3.a PCR Repetition : Event ID = 3117

MTM400A Test Parameter and Configuration File Technical Reference

1−3

Test Parameters - Standards Tests

2.3.b PCR Discontinuity Indicator : Event ID = 3151 PID Test : 2.3.b PCR Discontinuity Indicator : Event ID = 3118

2.4 PCR Accuracy : Event ID = 3024 PID Test : 2.4 PCR Accuracy : Event ID = 3028

2.5 PTS : Event ID = 3025 PID Test : 2.5 PTS : Event ID = 3728

2.6 CAT : Event ID = 3026

2.6 CAT (Scrambling) : Event ID = 3114

Priority 3 : Event ID = 37f5

3.2 SI repetition : Event ID = 3032 CAT max subtable RI : Event ID = 3115 PAT max section RI : Event ID = 3950

3.4.a Unref PID : Event ID = 303b PID Test : 3.4.a Unref PID : Event ID = 303a

Other : Event ID = 37f2

Table Tests : Event ID = 37f6

Any Table Syntax : Event ID = 3520

PAT Syntax : Event ID = 3500 PMT Syntax : Event ID = 3501 CAT Syntax : Event ID = 3502

DPI/SIT Syntax : Event ID = 3828 Table Id Error : Event ID = 37fb Timer Error : Event ID = 37fc PAT/PMT Consistency : Event ID = 3330

Miscellaneous : Event ID = 37f9

TS Availability : Event ID = 3053 PID Occupancy : Event ID = 2001

PID Test : PID Occupancy : Event ID = 2004 Prog Occupancy : Event ID = 2002

Progran occupancy error : Event ID = 3039

Program Test : Prog Occupancy : Event ID = 3039 PCR Overall Jitter (PCR_OJ) : Event ID = 3040

PID Test : PCR Overall Jitter (PCR_OJ) : Event ID = 3043 PCR Frequency Offset (PCR_FO) : Event ID = 3041

PID Test : PCR Frequency Offset (PCR_FO) : Event ID = 3044 PCR Drift Rate (PCR_DR) : Event ID = 3042

PID Test : PCR Drift Rate (PCR_DR) : Event ID = 3045 DPI/SIT Any Errors : Event ID = 382a

Multiple (>1) DPI/SIT PIDs per Program : Event ID = 3823

Excess (>8) DPI/SIT PIDs per Program : Event ID = 3824

DPI/SIT Encrypted Error : Event ID = 3825

DPI/SIT Missing : Event ID = 3826

Ind DPI/SIT Missing : Event ID = 3827 DPI/SIT Syntax : Event ID = 3828 DPI/SIT Max subtable RI : Event ID = 3829

DPI/SIT Any information events : Event ID = c01d

DPI/SIT Data : Event ID = c017 DPI/SIT Splice Cancel : Event ID = c018 DPI/SIT Splice : Event ID = c019 DPI/SIT Program Splice : Event ID = c01a DPI/SIT Component Splice : Event ID = c01b

PID Group Occupancy : Event ID = 2005

PID group occupancy error : Event ID = 2003

PID Bit Rate Variability : Event ID = 2010

PID Test : PID Bit Rate Variability : Event ID = 2011

Discontinuity : Event ID = 3131

1−4

MTM400A Test Parameter and Configuration File Technical Reference

Test Parameters - Standards Tests

PID Test : Discontinuity : Event ID = 3133 Transport Stream Occupancy : Event ID = 3600 Service Log Overflow : Event ID = 5200 Program Information : Event ID = c001 PTS/DTS Syntax Error : Event ID = 3054

Any Template Error : Event ID = 6fff

Template Header Error : Event ID = 6000

Template TransportStreamId error : Event ID = 6010

Template NetworkId error : Event ID = 6020

Template OriginalNetworkId error : Event ID = 6030

Template ServiceNumber error : Event ID = 6040 Any Template Service Error : Event ID = 6100

Template PcrPid error : Event ID = 6110

Template ServiceType error : Event ID = 6120

Template ServiceName error : Event ID = 6130

Template Service constraint error : Event ID = 6140

Template OtherPidsAllowed error : Event ID = 6150 Any Template PID Error : Event ID = 6200

Template CADescriptorPresent error : Event ID = 6210

Template Pid scrambling error : Event ID = 6220

Template StreamType error : Event ID = 6230

Template Pid constraint error : Event ID = 6240 Any Template Rating Error : Event ID = 6300

Template DVB/ATSC Ratings error : Event ID = 6301

DVB Tests

Any Stream error : Event ID = 2000

TR 101 290 : Event ID = 37f7

Priority 1 : Event ID = 37f3

1.1 Sync : Event ID = 3011

1.2 Sync Byte : Event ID = 3012

1.3.a PAT : Event ID = 3018

1.3 PAT (Timer) : Event ID = 3100

1.3 PAT (Table ID) : Event ID = 3101

1.3 PAT (Scrambling) : Event ID = 3102

PAT max section RI : Event ID = 3950

1.4 Continuity : Event ID = 3014

PID Test : 1.4 Continuity : Event ID = 3132

1.5.a PMT : Event ID = 3019

1.5 PMT (Timer) : Event ID = 3103 Ind PMT Err Timer : Event ID = 3160 Program Test : 1.5 PMT (Timer) : Event ID = 3160

1.5 PMT (Scrambling) : Event ID = 3104

1.6 PID : Event ID = 3016 PID Test : 1.6 PID : Event ID = 3017

Priority 2 : Event ID = 37f4

2.1 Transport : Event ID = 3021

2.2 CRC : Event ID = 3022

2.3.a PCR Repetition : Event ID = 3150 PID Test : 2.3.a PCR Repetition : Event ID = 3117

2.3.b PCR Discontinuity Indicator : Event ID = 3151 PID Test : 2.3.b PCR Discontinuity Indicator : Event ID = 3118

2.4 PCR Accuracy : Event ID = 3024

MTM400A Test Parameter and Configuration File Technical Reference

1−5

Test Parameters - Standards Tests

PID Test : 2.4 PCR Accuracy : Event ID = 3028

2.5 PTS : Event ID = 3025 PID Test : 2.5 PTS : Event ID = 3728

2.6 CAT : Event ID = 3026

2.6 CAT (Table ID) : Event ID = 3107

2.6 CAT (Scrambling) : Event ID = 3114

Priority 3 : Event ID = 37f5

3.1.a NIT Actual : Event ID = 3140

3.1 NIT (Table ID) : Event ID = 3109 NIT Actual Min Any Section Reptn Int : Event ID = 3955 NIT Actual Timer : Event ID = 3951

3.1b NIT Other : Event ID = 3708 Ind NIT other max section RI : Event ID = 372d

3.2 SI Repetition : Event ID = 3032 TDT max section RI : Event ID = 395a NIT Actual Min Section Reptn Int : Event ID = 3703

Ind NIT actual min section RI : Event ID = 3729 NIT Actual Max Section Reptn Int : Event ID = 3705 NIT Actual Max Subtable Reptn Int : Event ID = 3704

Ind NIT actual max subtable RI : Event ID = 372a NIT Other Min Section Reptn Int : Event ID = 3706

Ind NIT other min section RI : Event ID = 372b NIT Other Max Subtable Reptn Int : Event ID = 3707

Ind NIT other max subtable RI : Event ID = 372c SDT Actual Min Section Reptn Int : Event ID = 3709

Ind SDT actual min section RI : Event ID = 372e SDT Actual Max Section Reptn Int : Event ID = 370b SDT Actual Max Subtable Reptn Int : Event ID = 370a

Ind SDT actual max subtable RI : Event ID = 372f SDT Other Min Section Reptn Int : Event ID = 370c

Ind SDT other min section RI : Event ID = 3730 SDT Other Max Subtable Reptn Int : Event ID = 370d

Ind SDT other max subtable RI : Event ID = 3731 EIT Actual P Max Sect Reptn Int : Event ID = 3711 EIT Actual F Max Sect Reptn Int : Event ID = 3712 EIT Actual PF Min Sect Reptn Int : Event ID = 370f

Ind DVB EIT actual p/f min section RI : Event ID = 3733 EIT Actual PF Max Subtable Reptn Int : Event ID = 3710

Ind DVB EIT actual p/f max subtable RI : Event ID = 3734 EIT Other PF Min Sect Reptn Int : Event ID = 3713

Ind DVB EIT other p/f min section RI : Event ID = 3735 EIT Other PF Max Subtable Reptn Int : Event ID = 3714

Ind DVB EIT other p/f max subtable RI : Event ID = 3736 EIT Other P Max Sect Reptn Int : Event ID = 3715 EIT Other F Max Sect Reptn Int : Event ID = 3716 EIT Actual Sched Min Sect Reptn Int : Event ID = 3717

Ind DVB EIT actual schedule min section RI : Event ID = 3737 EIT Actual Sched Max Subtable Reptn Int : Event ID = 3718

Ind DVB EIT actual schedule max subtable RI : Event ID = 3738 EIT Other Sched Min Sect Reptn Int : Event ID = 3719

Ind DVB EIT other schedule min section RI : Event ID = 3739 EIT Other Sched Max Subtable Reptn Int : Event ID = 371a

Ind DVB EIT other schedule max subtable RI : Event ID = 373a RST Min Sect Reptn Int : Event ID = 371b

Ind RST min section RI : Event ID = 373b TDT Min Sect Reptn Int : Event ID = 371c

1−6

MTM400A Test Parameter and Configuration File Technical Reference

Test Parameters - Standards Tests

Ind TDT min section RI : Event ID = 373c

TOT Min Sect Reptn Int : Event ID = 371e

Ind TOT min section RI : Event ID = 373d TOT Max Sect Reptn Int : Event ID = 371f BAT Min Sect Reptn Int : Event ID = 3720

Ind BAT min section RI : Event ID = 373e BAT Max Subtable Reptn Int : Event ID = 3721

Ind BAT max subtable RI : Event ID = 373f CAT max subtable RI : Event ID = 3115

3.4.a Unref PID : Event ID = 303b PID Test : 3.4.a Unref PID : Event ID = 303a

3.5.a SDT Actual : Event ID = 3142

3.5 SDT (Table ID) : Event ID = 3106 SDT Actual Min Any Section Reptn Int : Event ID = 3956 SDT Actual Timer : Event ID = 3952

3.5b SDT Other : Event ID = 370e Ind SDT other max section RI : Event ID = 3732

3.6.a EIT Actual : Event ID = 3143

3.6 EIT (Table ID) : Event ID = 3111 EIT Actual PF Min Any Section Reptn Int : Event ID = 3957 EIT Actual P Timer : Event ID = 3953 EIT Actual F Timer : Event ID = 3954

3.6.b EIT Other : Event ID = 3144 EIT Other P Max Sect Reptn Int : Event ID = 3715 EIT Other F Max Sect Reptn Int : Event ID = 3716

3.6.c EIT PF : Event ID = 3333 EIT P/F Presence : Event ID = 3051 EIT P/F Presence Consistency : Event ID = 3052

3.7 RST : Event ID = 3037 RST (Table ID) : Event ID = 3120 RST Min Any Sect Reptn Int : Event ID = 3959

3.8 TDT : Event ID = 3038

3.8 TDT (Timer) : Event ID = 3112

3.8 TDT (Table ID) : Event ID = 3113 TDT Min Any Sect Reptn Int : Event ID = 3958

Other : Event ID = 37f2

Table Tests : Event ID = 37f6

Any Table Syntax : Event ID = 3520

PAT Syntax : Event ID = 3500 PMT Syntax : Event ID = 3501 CAT Syntax : Event ID = 3502 NIT Syntax : Event ID = 3503 BAT Syntax : Event ID = 3504 SDT Syntax : Event ID = 3505 EIT Syntax : Event ID = 3506 TDT Syntax : Event ID = 3507 TOT Syntax : Event ID = 3508 RST Syntax : Event ID = 3509 DPI/SIT Syntax : Event ID = 3828 SIT Syntax : Event ID = 351e DIT Syntax : Event ID = 351f

Table Id Error : Event ID = 37fb

3.8 TDT (Table ID) : Event ID = 3113 SIT (Table ID) : Event ID = 311f DIT (Table ID) : Event ID = 3126 RST (Table ID) : Event ID = 3120

MTM400A Test Parameter and Configuration File Technical Reference

1−7

Test Parameters - Standards Tests

Timer Error : Event ID = 37fc

3.8 TDT (Timer) : Event ID = 3112 CAT Timer : Event ID = 395b PAT/PMT Consistency : Event ID = 3330 PAT/SDT Consistency : Event ID = 3331

Miscellaneous : Event ID = 37f9

TS Availability : Event ID = 3053 PID Occupancy : Event ID = 2001

PID Test : PID Occupancy : Event ID = 2004

Prog Occupancy : Event ID = 2002

Program occupancy error : Event ID = 3039 Program Test : Prog Occupancy : Event ID = 3039

PCR Overall Jitter (PCR_OJ) : Event ID = 3040

PID Test : PCR Overall Jitter (PCR_OJ) : Event ID = 3043

PCR Frequency Offset (PCR_FO) : Event ID = 3041

PID Test : PCR Frequency Offset (PCR_FO) : Event ID = 3044

PCR Drift Rate (PCR_DR) : Event ID = 3042

PID Test : PCR Drift Rate (PCR_DR) : Event ID = 3045

DPI/SIT Any Errors : Event ID = 382a

Multiple (>1) DPI/SIT PIDs per Program : Event ID = 3823 Excess (>8) DPI/SIT PIDs per Program : Event ID = 3824 DPI/SIT Encrypted Error : Event ID = 3825 DPI/SIT Missing : Event ID = 3826

Ind DPI/SIT Missing : Event ID = 3827 DPI/SIT Syntax : Event ID = 3828 DPI/SIT Max subtable RI : Event ID = 3829

DPI/SIT Any information events : Event ID = c01d

DPI/SIT Data : Event ID = c017"/> DPI/SIT Splice Cancel : Event ID = c018"/> DPI/SIT Splice : Event ID = c019"/> DPI/SIT Program Splice : Event ID = c01a"/> DPI/SIT Component Splice : Event ID = c01b"/>

PID Group Occupancy : Event ID = 2005

PID group occupancy error : Event ID = 2003

PID Bit Rate Variability : Event ID = 2010

PID Test : PID Bit Rate Variability : Event ID = 2011

Discontinuity : Event ID = 3131

PID Test : Discontinuity : Event ID = 3133

Transport Stream Occupancy : Event ID = 3600 Service Log Overflow : Event ID = 5200

Any Template Error : Event ID = 6fff

Template Header Error : Event ID = 6000

Template TransportStreamId error : Event ID = 6010 Template NetworkId error : Event ID = 6020 Template OriginalNetworkId error : Event ID = 6030 Template ServiceNumber error : Event ID = 6040

Any Template Service Error : Event ID = 6100

Template PcrPid error : Event ID = 6110 Template ServiceType error : Event ID = 6120 Template ServiceName error : Event ID = 6130 Template Service constraint error : Event ID = 6140 Template OtherPidsAllowed error : Event ID = 6150

Any Template PID Error : Event ID = 6200

Template CADescriptorPresent error : Event ID = 6210 Template Pid scrambling error : Event ID = 6220 Template StreamType error : Event ID = 6230

1−8

MTM400A Test Parameter and Configuration File Technical Reference

ATSC Tests

Test Parameters - Standards Tests

Template Pid constraint error : Event ID = 6240

Any Template Rating Error : Event ID = 6300

Template DVB/ATSC Ratings error : Event ID = 6301

SFN Error : Event ID = 3400

SFN (No MIP) : Event ID = 3401

SFN One MIP per M/F : Event ID = 3410

SFN Repetition : Event ID = 3411 SFN (Invalid MIP) : Event ID = 3403

SFN MIP Length : Event ID = 3412

SFN CRC : Event ID = 3413

SFN MIP Coding : Event ID = 3414

SFN Periodicity Consistency : Event ID = 3415

SFN Pointer Consistency : Event ID = 3416 SFN (Timer) : Event ID = 3404

Priority Tests : Event ID = 37f7

Priority 1 : Event ID = 37f3

1.1 Sync : Event ID = 3011

1.2 Sync Byte : Event ID = 3012

1.3.a PAT : Event ID = 3018

1.3 PAT (Timer) : Event ID = 3100

1.3 PAT (Table ID) : Event ID = 3101

1.3 PAT (Scrambling) : Event ID = 3102

1.4 Continuity : Event ID = 3014

PID Test = 1.4 Continuity : Event ID = 3132

1.5.a PMT : Event ID = 3019

1.5 PMT (Timer) : Event ID = 3103 Ind PMT Err Timer : Event ID = 3160 Program Test = 1.5 PMT (Timer) : Event ID = 3160

1.5 PMT (Scrambling) : Event ID = 3104

1.6 PID : Event ID = 3016 PID Test = 1.6 PID : Event ID = 3017

Priority 2 : Event ID = 37f4

2.1 Transport : Event ID = 3021

2.2 CRC : Event ID = 3022

2.3.a PCR Repetition : Event ID = 3150 PID Test = 2.3.a PCR Repetition : Event ID = 3117

2.3.b PCR Discontinuity Indicator : Event ID = 3151 PID Test = 2.3.b PCR Discontinuity Indicator : Event ID = 3118

2.4 PCR Accuracy : Event ID = 3024 PID Test = 2.4 PCR Accuracy : Event ID = 3028

2.5 PTS : Event ID = 3025 PID Test = 2.5 PTS : Event ID = 3728

2.6 CAT : Event ID = 3026

2.6 CAT (Scrambling) : Event ID = 3114

Other : Event ID = 37f2

Table Tests : Event ID = 37f6

Any Table Syntax : Event ID = 3520

PAT Syntax : Event ID = 3500 PMT Syntax : Event ID = 3501 CAT Syntax : Event ID = 3502 MGT Syntax : Event ID = 350a

MTM400A Test Parameter and Configuration File Technical Reference

1−9

Test Parameters - Standards Tests

RRT Syntax : Event ID = 350b VCT Syntax : Event ID = 350c EIT−k Syntax : Event ID = 350d STT Syntax : Event ID = 350e ETT Syntax : Event ID = 350f DCCT Syntax : Event ID = 3510 DCCSCT Syntax : Event ID = 3511

DPI/SIT Syntax : Event ID = 3828 Table Id Error : Event ID = 37fb Timer Error : Event ID = 37fc

A/65 VCT (Timer) : Event ID = 3210

Ind VCT max subtable RI : Event ID = 374b A/65 MGT (Timer) : Event ID = 3211 A/65 STT (Timer) : Event ID = 3212 A/65 RRT (Timer) : Event ID = 3213

A/65 MGT : Event ID = 3201

A/65 MGT (Timer) : Event ID = 3211 MGT Missing : Event ID = 3755

A/65 STT : Event ID = 3202

A/65 STT (Timer) : Event ID = 3212 STT Missing : Event ID = 3758

A/65 RRT : Event ID = 3203

A/65 RRT (Timer) : Event ID = 3213 RRT Missing : Event ID = 3757

A/65 EIT : Event ID = 3204

EIT−0,1,2,3 Max Sect Reptn Int : Event ID = 3727 EIT−0,1,2,3 Missing : Event ID = 3759

A/65 VCT : Event ID = 3205

A/65 VCT (Timer) : Event ID = 3210

Ind VCT max subtable RI : Event ID = 374b VCT Max Sect Reptn Int : Event ID = 374c VCT Missing : Event ID = 3756

A/65 ETT : Event ID = 3206 MGT/EIT−k presence : Event ID = 3230 MGT Missing : Event ID = 3755 VCT Missing : Event ID = 3756 EIT−0,1,2,3 Missing : Event ID = 3759 STT Missing : Event ID = 3758 RRT Missing : Event ID = 3757 PAT/PMT Consistency : Event ID = 3330 PAT/VCT consistency : Event ID = 3332 EIT−0,1,2,3 Max Sect Reptn Int : Event ID = 3727

Miscellaneous : Event ID = 37f9

TS Availability : Event ID = 3053 PID Occupancy : Event ID = 2001

PID Test = PID Occupancy : Event ID = 2004

Prog Occupancy : Event ID = 2002

Progran occupancy error : Event ID = 3039 Program Test = Prog Occupancy : Event ID = 3039

PCR Overall Jitter (PCR_OJ) : Event ID = 3040

PID Test = PCR Overall Jitter (PCR_OJ) : Event ID = 3043

PCR Frequency Offset (PCR_FO) : Event ID = 3041

PID Test = PCR Frequency Offset (PCR_FO) : Event ID = 3044

PCR Drift Rate (PCR_DR) : Event ID = 3042

PID Test = PCR Drift Rate (PCR_DR) : Event ID = 3045

DPI/SIT Any Errors : Event ID = 382a

1−10

MTM400A Test Parameter and Configuration File Technical Reference

Test Parameters - Standards Tests

Multiple (>1) DPI/SIT PIDs per Program : Event ID = 3823 Excess (>8) DPI/SIT PIDs per Program : Event ID = 3824 DPI/SIT Encrypted Error : Event ID = 3825 DPI/SIT Missing : Event ID = 3826

Ind DPI/SIT Missing : Event ID = 3827 DPI/SIT Syntax : Event ID = 3828 DPI/SIT Max subtable RI : Event ID = 3829

DPI/SIT Any information events : Event ID = c01d

DPI/SIT Data : Event ID = c017 DPI/SIT Splice Cancel : Event ID = c018 DPI/SIT Splice : Event ID = c019 DPI/SIT Program Splice : Event ID = c01a DPI/SIT Component Splice : Event ID = c01b

PID Group Occupancy : Event ID = 2005

PID group occupancy error : Event ID = 2003

PID Bit Rate Variability : Event ID = 2010

PID Test = PID Bit Rate Variability : Event ID = 2011

Discontinuity : Event ID = 3131

PID Test = Discontinuity : Event ID = 3133

A/65 Base PID : Event ID = 3208 A53 non−AC3 Audio : Event ID = 3860 A/53 Prog P’digm : Event ID = 3320 Transport Stream Occupancy : Event ID = 3600 Service Log Overflow : Event ID = 5200 Program Information : Event ID = c001 PTS/DTS Syntax Error : Event ID = 3054

Any Template Error : Event ID = 6fff

Template Header Error : Event ID = 6000

Template TransportStreamId error : Event ID = 6010 Template NetworkId error : Event ID = 6020 Template OriginalNetworkId error : Event ID = 6030 Template ServiceNumber error : Event ID = 6040

Any Template Service Error : Event ID = 6100

Any Template PID Error : Event ID = 6200

Template CADescriptorPresent error : Event ID = 6210 Template Pid scrambling error : Event ID = 6220 Template StreamType error : Event ID = 6230 Template Pid constraint error : Event ID = 6240

Any Template Rating Error : Event ID = 6300

Template DVB/ATSC Ratings error : Event ID = 6301

MTM400A Test Parameter and Configuration File Technical Reference

1−11

Test Parameters - Standards Tests

ISDB-S Tests

Priority Tests : EventID = 37f7

Priority 1 : EventID = 37f3

1.1 Sync : EventID = 3011

1.2 Sync Byte : EventID = 3012

1.3.a PAT : EventID = 3018

1.3 PAT (Timer) : EventID = 3100

1.3 PAT (Table ID) : EventID = 3101

1.3 PAT (Scrambling) : EventID = 3102

1.4 Continuity : EventID = 3014 PID Test : 1.4 Continuity : EventID = 3132

1.5.a PMT : EventID = 3019

1.5 PMT (Timer) : EventID = 3103

Ind PMT Err Timer : EventID = 3160 Program Test : 1.5 PMT (Timer) : EventID = 3160

1.5 PMT (Scrambling) : EventID = 3104

1.6 PID : EventID = 3016 PID Test : 1.6 PID : EventID = 3017

Priority 2 : EventID = 37f4

2.1 Transport : EventID = 3021

2.2 CRC : EventID = 3022

2.3.a PCR Repetition : EventID = 3150 PID Test : 2.3.a PCR Repetition : EventID = 3117

2.3.b PCR Discontinuity Indicator : EventID = 3151 PID Test : 2.3.b PCR Discontinuity Indicator : EventID = 3118

2.4 PCR Accuracy : EventID = 3024 PID Test : 2.4 PCR Accuracy : EventID = 3028

2.5 PTS : EventID = 3025 PID Test : 2.5 PTS : EventID = 3728

2.6 CAT : EventID = 3026

2.6 CAT (Table ID) : EventID = 3107

2.6 CAT (Scrambling) : EventID = 3114

Priority 3 : EventID = 37f5

3.1.a NIT Actual : EventID = 3140

3.1 NIT (Table ID) : EventID = 3109 NIT Actual Timer : EventID = 3951

3.1.b NIT Other : EventID = 3708 Ind NIT other max section RI : EventID = 372d

3.2 SI Repetition : EventID = 3032 NIT Actual Min Section Reptn Int : EventID = 3703

Ind NIT actual min section RI : EventID = 3729 NIT Actual Max Section Reptn Int : EventID = 3705 NIT Actual Max Subtable Reptn Int : EventID = 3704

Ind NIT actual max subtable RI : EventID = 372a SDT Actual Min Section Reptn Int : EventID = 3709

Ind SDT actual min section RI : EventID = 372e SDT Actual Max Section Reptn Int : EventID = 370b SDT Actual Max Subtable Reptn Int : EventID = 370a

Ind SDT actual max subtable RI : EventID = 372f SDT Other Min Section Reptn Int : EventID = 370c

Ind SDT other min section RI : EventID = 3730 SDT Other Max Subtable Reptn Int : EventID = 370d

Ind SDT other max subtable RI : EventID = 3731 EIT Actual PF Min Sect Reptn Int : EventID = 370f

Ind DVB EIT actual p/f min section RI : EventID = 3733

1−12

MTM400A Test Parameter and Configuration File Technical Reference

Test Parameters - Standards Tests

EIT Actual PF Max Subtable Reptn Int : EventID = 3710

Ind DVB EIT actual p/f max subtable RI : EventID = 3734

EIT Other PF Min Sect Reptn Int : EventID = 3713

Ind DVB EIT other p/f min section RI : EventID = 3735

EIT Other PF Max Subtable Reptn Int : EventID = 3714

Ind DVB EIT other p/f max subtable RI : EventID = 3736

EIT Actual Sched Min Sect Reptn Int : EventID = 3717

Ind DVB EIT actual schedule min section RI : EventID = 3737

EIT Actual Sched Max Subtable Reptn Int : EventID = 3718

Ind DVB EIT actual schedule max subtable RI : EventID = 3738

EIT Other Sched Min Sect Reptn Int : EventID = 3719

Ind DVB EIT other schedule min section RI : EventID = 3739

EIT Other Sched Max Subtable Reptn Int : EventID = 371a

Ind DVB EIT other schedule max subtable RI : EventID = 373a

TOT Min Section Reptn Int : EventID = 371e

Ind TOT min section RI : EventID = 373d

TOT Max Section Reptn Int : EventID = 371f

3.1.b NIT Other : EventID = 3708 Ind NIT other max section RI : EventID = 372d

3.5.b SDT Other : EventID = 370e Ind SDT other max section RI : EventID = 3732

CAT max subtable RI : EventID = 3115 SDTT Max Subtable Reptn Int : EventID = 3761

Ind SDTT max subtable RI : EventID = 3742

BIT Max Subtable Reptn Int : EventID = 3763

Ind BIT max subtable RI : EventID = 3744

SDTT Min Sect Reptn Int : EventID = 3760

Ind SDTT min section RI : EventID = 3741

BIT Min Sect Reptn Int : EventID = 3762

Ind BIT min section RI : EventID = 3743

PAT max section RI : EventID = 3950

3.4.a Unreferenced PID : EventID = 303b PID Test : 3.4.a Unreferenced PID : EventID = 303a

3.5.a SDT Actual : EventID = 3142

3.5 SDT (Table ID) : EventID = 3106 SDT Actual Timer : EventID = 3952

3.5.b SDT Other : EventID = 370e Ind SDT other max section RI : EventID = 3732

3.6.b EIT Other : EventID = 3144 EIT Other P Max Sect Reptn Int : EventID = 3715 EIT Other F Max Sect Reptn Int : EventID = 3716

3.6c EIT PF : EventID = 3333 Ind DVB EIT P/F presence consistency : EventID = 3051 DVB EIT P/F Presence Consistency : EventID = 3052

Other : EventID = 37f2

Table Tests : EventID = 37f6

Any Table Syntax : EventID = 3520

MTM400A Test Parameter and Configuration File Technical Reference

1−13

Test Parameters - Standards Tests

DPI/SIT Syntax : EventID = 3828

Table Id Error : EventID = 37fb

TOT (Table ID) : EventID = 3119 SDTT (Table Id) : EventID = 3780 BIT (Table Id) : EventID = 3781

TOT : EventID = 3134

TOT Min Section Reptn Int : EventID = 371e

Ind TOT min section RI : EventID = 373d TOT Max Section Reptn Int : EventID = 371f TOT (Table ID) : EventID = 3119

SDTT : EventID = 3770

SDTT Min Sect Reptn Int : EventID = 3760

Ind SDTT min section RI : EventID = 3741 SDTT Max Subtable Reptn Int : EventID = 3761

Ind SDTT max subtable RI : EventID = 3742 SDTT (Table Id) : EventID = 3780

BIT : EventID = 3771

BIT Min Sect Reptn Int : EventID = 3762

Ind BIT min section RI : EventID = 3743 BIT Max Subtable Reptn Int : EventID = 3763

Ind BIT max subtable RI : EventID = 3744 BIT (Table Id) : EventID = 3781

PAT/PMT Consistency : EventID = 3330 DSM−CC error : EventID = 3910

DII min RI : EventID = 3908

Ind DII min repetition error : EventID = 3909 DII max RI : EventID = 390c

Ind DII max repetition error : EventID = 390d DII Timeout : EventID = 3905 DII download completion : EventID = 390e

Ind DII completition : EventID = 390f

Miscellaneous : EventID = 37f9

TS Availability : EventID = 3053 PID Occupancy : EventID = 2001

PID Test : PID Occupancy : EventID = 2004

Prog Occupancy : EventID = 2002

Progran occupancy error : EventID = 3039 Program Test : Prog Occupancy : EventID = 3039

PCR Overall Jitter (PCR_OJ) : EventID = 3040

PID Test : PCR Overall Jitter (PCR_OJ) : EventID = 3043

PCR Frequency Offset (PCR_FO) : EventID = 3041

PID Test : PCR Frequency Offset (PCR_FO) : EventID = 3044

PCR Drift Rate (PCR_DR) : EventID = 3042

PID Test : PCR Drift Rate (PCR_DR) : EventID = 3045

DPI/SIT Any Errors : EventID = 382a

Multiple (>1) DPI/SIT PIDs per Program : EventID = 3823 Excess (>8) DPI/SIT PIDs per Program : EventID = 3824 DPI/SIT Encrypted Error : EventID = 3825 DPI/SIT Missing : EventID = 3826

Ind DPI/SIT Missing : EventID = 3827 DPI/SIT Syntax : EventID = 3828 DPI/SIT Max subtable RI : EventID = 3829

DPI/SIT Any information events : EventID = c01d

DPI/SIT Data : EventID = c017 DPI/SIT Splice Cancel : EventID = c018 DPI/SIT Splice : EventID = c019

1−14

MTM400A Test Parameter and Configuration File Technical Reference

Test Parameters - Standards Tests

DPI/SIT Program Splice : EventID = c01a DPI/SIT Component Splice : EventID = c01b

PID Group Occupancy : EventID = 2005

PID group occupancy error : EventID = 2003

PID Bit Rate Variability : EventID = 2010

PID Test : PID Bit Rate Variability : EventID = 2011

Discontinuity : EventID = 3131

PID Test : Discontinuity : EventID = 3133 Transport Stream Occupancy : EventID = 3600 Service Log Overflow : EventID = 5200 Program Information : EventID = c001 PTS/DTS Syntax Error : EventID = 3054

Any Template Error : EventID = 6fff

Template Header Error : EventID = 6000

Template TransportStreamId error : EventID = 6010

Template NetworkId error : EventID = 6020

Template OriginalNetworkId error : EventID = 6030

Template ServiceNumber error : EventID = 6040 Any Template Service Error : EventID = 6100

Template PcrPid error : EventID = 6110

Template ServiceType error : EventID = 6120

Template ServiceName error : EventID = 6130

Template Service constraint error : EventID = 6140

Template OtherPidsAllowed error : EventID = 6150 Any Template PID Error : EventID = 6200

Template CADescriptorPresent error : EventID = 6210

Template Pid scrambling error : EventID = 6220

Template StreamType error : EventID = 6230

Template Pid constraint error : EventID = 6240 Any Template Rating Error : EventID = 6300

Template DVB/ATSC Ratings error : EventID = 6301

ISDB-T Tests

ISDB Tests : Event ID = 37f8

ISDBT NIT Terrestrial Delivery Validation : Event ID = 37a1

ISDBT Mode/Guard Interval Validation : Event ID = 379e ISDBT Time Interleaving Validation : Event ID = 379f ISDBT Modulation/Error Compensation Validation : Event ID = 37a0 ISDBT Partial Reception/TS Information Consistency : Event ID = 37a3

ISDBT Guard Interval Consistency : Event ID = 379a ISDBT Transmission Mode Consistency : Event ID = 379b ISDBT Partial Reception Consistency : Event ID = 379c ISDBT Modulation Consistency : Event ID = 379d ISDBT NIT Service List Consistency : Event ID = 37a2 ISDBT EIT Type Content Check : Event ID = 37a5 ISDBT EIT Unique Event Id : Event ID = 37a6 ISDBT SDT/EIT Consistency : Event ID = 37a7

Ind ISDBT SDT/EIT Consistency : Event ID = 37a8

ISDBT NIT/EIT Consistency : Event ID = 37aa

Ind ISDBT NIT/EIT Consistency : Event ID = 37ab

Ind ISDBT NIT/EIT Consistency : Event ID = 37ab ISDBT NIT/SDT Consistency : Event ID = 37b1

MTM400A Test Parameter and Configuration File Technical Reference

1−15

Test Parameters - Standards Tests

ISDBT Any IIP CRC : Event ID = 37b4

ISDBT IIP MCCI CRC : Event ID = 37b2

ISDBT IIP SFN Sync CRC : Event ID = 37b3 ISDBT IIP Branching : Event ID = 37c1 ISDBT IIP Error : Event ID = 37c2 ISDBT TMCC Id Error : Event ID = 37c3 ISDBT Max Partial Reception Services Error : Event ID = 37c4 ISDBT NIT/PMT Consistency : Event ID = 37c5 ISDBT Partial Reception Service ID Check : Event ID = 37c6 HEIT Schedule : Event ID = 37fd

H−EIT basic schedule max subtable RI for TV : Event ID = 37b5

Ind H−EIT basic schedule max subtable RI for TV Cycle Group 1 :

Event ID = 37d0

Ind H−EIT basic schedule max subtable RI for TV Cycle Group 2 :

Event ID = 37d1

Ind H−EIT basic schedule max subtable RI for TV Cycle Group 3 :

Event ID = 37d2

Ind H−EIT basic schedule max subtable RI for TV Cycle Group Base :

Event ID = 37d3

H−EIT basic schedule max subtable RI for audio : Event ID = 37b6

Ind H−EIT basic schedule max subtable RI for audio Cycle Group 1 :

Event ID = 37d4

Ind H−EIT basic schedule max subtable RI for audio Cycle Group 2 :

Event ID = 37d5

Ind H−EIT basic schedule max subtable RI for audio Cycle Group 3 :

Event ID = 37d6

Ind H−EIT basic schedule max subtable RI for audio Cycle Group Base :

Event ID = 37d7

H−EIT basic schedule max subtable RI for data : Event ID = 37b7

Ind H−EIT basic schedule max subtable RI for data Cycle Group 1 :

Event ID = 37d8

Ind H−EIT basic schedule max subtable RI for data Cycle Group 2 :

Event ID = 37d9

Ind H−EIT basic schedule max subtable RI for data Cycle Group 3 :

Event ID = 37da

Ind H−EIT basic schedule max subtable RI for data Cycle Group Base :

Event ID = 37db

H−EIT extended schedule max subtable RI for TV : Event ID = 37b8

Ind H−EIT basic schedule max subtable RI for TV Cycle Group 1 :

Event ID = 37dc

Ind H−EIT basic schedule max subtable RI for TV Cycle Group 2 :

Event ID = 37dd

Ind H−EIT basic schedule max subtable RI for TV Cycle Group 3 :

Event ID = 37de

Ind H−EIT basic schedule max subtable RI for TV Cycle Group Base :

Event ID = 37df

H−EIT extended schedule max subtable RI for audio : Event ID = 37b9

Ind H−EIT basic schedule max subtable RI for audio Cycle Group 1 :

Event ID = 37e0

Ind H−EIT basic schedule max subtable RI for audio Cycle Group 2 :

Event ID = 37e1

Ind H−EIT basic schedule max subtable RI for audio Cycle Group 3 :

Event ID = 37e2

Ind H−EIT basic schedule max subtable RI for audio Cycle Group Base :

Event ID = 37e3

H−EIT extended schedule max subtable RI for data : Event ID = 37ba

1−16

MTM400A Test Parameter and Configuration File Technical Reference

Test Parameters - Standards Tests

Ind H−EIT basic schedule max subtable RI for data Cycle Group 1 :

Event ID = 37e4

Ind H−EIT basic schedule max subtable RI for data Cycle Group 2 :

Event ID = 37e5

Ind H−EIT basic schedule max subtable RI for data Cycle Group 3 :

Event ID = 37e6

Ind H−EIT basic schedule max subtable RI for data Cycle Group Base : Event ID = 37e7 Priority Tests : Event ID = 37f7

Priority 1 : Event ID = 37f3

1.1 Sync : Event ID = 3011

1.2 Sync Byte : Event ID = 3012

1.3.a PAT : Event ID = 3018

1.3 PAT (Timer) : Event ID = 3100

1.3 PAT (Table ID) : Event ID = 3101

1.3 PAT (Scrambling) : Event ID = 3102

1.4 Continuity : Event ID = 3014 PID Test : 1.4 Continuity : Event ID = 3132

1.5.a PMT : Event ID = 3019

1.5 PMT (Timer) : Event ID = 3103

Ind PMT Err Timer : Event ID = 3160 Program Test : 1.5 PMT (Timer) : Event ID = 3160

1.5 PMT (Scrambling) : Event ID = 3104

1.6 PID : Event ID = 3016 PID Test : 1.6 PID : Event ID = 3017

Priority 2 : Event ID = 37f4

2.1 Transport : Event ID = 3021

2.2 CRC : Event ID = 3022

2.3.a PCR Repetition : Event ID = 3150 PID Test : 2.3.a PCR Repetition : Event ID = 3117

2.3.b PCR Discontinuity Indicator : Event ID = 3151 PID Test : 2.3.b PCR Discontinuity Indicator : Event ID = 3118

2.4 PCR Accuracy : Event ID = 3024 PID Test : 2.4 PCR Accuracy : Event ID = 3028

2.5 PTS : Event ID = 3025 PID Test : 2.5 PTS : Event ID = 3728

2.6 CAT : Event ID = 3026

2.6 CAT (Table ID) : Event ID = 3107

2.6 CAT (Scrambling) : Event ID = 3114

Priority 3 : Event ID = 37f5

3.1.a NIT : Event ID = 3140

3.1 NIT (Table ID) : Event ID = 3109 NIT Actual Timer : Event ID = 3951

3.2 SI Repetition : Event ID = 3032 NIT Min Section Reptn Int : Event ID = 3703

Ind NIT actual min section RI : Event ID = 3729 NIT Max Section Reptn Int : Event ID = 3705 NIT Max Subtable Reptn Int : Event ID = 3704

Ind NIT actual max subtable RI : Event ID = 372a SDT Min Section Reptn Int : Event ID = 3709

Ind SDT actual min section RI : Event ID = 372e SDT Max Section Reptn Int : Event ID = 370b SDT Max Subtable Reptn Int : Event ID = 370a

Ind SDT actual max subtable RI : Event ID = 372f TOT Min Sect Reptn Int : Event ID = 371e

Ind TOT min section RI : Event ID = 373d

MTM400A Test Parameter and Configuration File Technical Reference

1−17

Test Parameters - Standards Tests

TOT Max Sect Reptn Int : Event ID = 371f CAT max subtable RI : Event ID = 3115 BIT Max Subtable Reptn Int : Event ID = 3763

Ind BIT max subtable RI : Event ID = 3744

CDT Max Subtable Reptn Int : Event ID = 3776

Ind CDT max subtable RI : Event ID = 374d

BIT Min Section Reptn Int : Event ID = 3762

Ind BIT min section RI : Event ID = 3743

CDT Min Sect Reptn Int : Event ID = 3775

Ind CDT min section RI : Event ID = 374e M−EIT Max Subtable Reptn Int : Event ID = 375c L−EIT Max Subtable Reptn Int : Event ID = 375e M−EIT Min Sect Reptn Int : Event ID = 375d L−EIT Min Sect Reptn Int : Event ID = 375f SDTT(H) max subtable RI : Event ID = 37e9

Ind SDTT(H) max subtable RI : Event ID = 37eb SDTT(H) min section RI : Event ID = 37e8

Ind SDTT(H) min section RI : Event ID = 37ea SDTT(L) max subtable RI : Event ID = 37ed

Ind SDTT(L) max subtable RI : Event ID = 37ef SDTT(L) min section RI : Event ID = 37ec

Ind SDTT(L) min section RI : Event ID = 37ee PAT max section RI : Event ID = 3950

3.4.a Unref PID : Event ID = 303b PID Test : 3.4.a Unref PID : Event ID = 303a

3.5.a SDT : Event ID = 3142

3.5 SDT (Table ID) : Event ID = 3106 SDT Actual Timer : Event ID = 3952

3.6c EIT PF : Event ID = 3333 Ind DVB EIT P/F presence consistency : Event ID = 3051 DVB EIT P/F Presence Consistency : Event ID = 3052

Other : Event ID = 37f2

Table Tests : Event ID = 37f6

Any Table Syntax : Event ID = 3520

PAT Syntax : Event ID = 3500 PMT Syntax : Event ID = 3501 CAT Syntax : Event ID = 3502 NIT Syntax : Event ID = 3503 SDT Syntax : Event ID = 3505 EIT Syntax : Event ID = 3506 TOT Syntax : Event ID = 3508 BIT Syntax : Event ID = 3792 CDT Syntax : Event ID = 3799 SDTT(L) Syntax : Event ID = 37f1 SDTT(H) Syntax : Event ID = 37f0 DPI/SIT Syntax : Event ID = 3828 H−EIT Syntax : Event ID = 3519 M−EIT Syntax : Event ID = 351a L−EIT Syntax : Event ID = 351b H−EIT Basic Schedule Syntax : Event ID = 351c H−EIT Extended Schedule Syntax : Event ID = 351d

Table Id Error : Event ID = 37fb

TOT (Table ID) : Event ID = 3119 H−EIT (Table ID) : Event ID = 311a M−EIT (Table ID) : Event ID = 311b L−EIT (Table ID) : Event ID = 311c

1−18

MTM400A Test Parameter and Configuration File Technical Reference

Test Parameters - Standards Tests

L−SDTT (Table ID) : Event ID = 311d H−SDTT (Table ID) : Event ID = 311e SIT (Table ID) : Event ID = 311f DIT (Table ID) : Event ID = 3126 BIT (Table ID) : Event ID = 3781

TOT : Event ID = 3134

TOT Min Sect Reptn Int : Event ID = 371e

Ind TOT min section RI : Event ID = 373d TOT Max Sect Reptn Int : Event ID = 371f TOT (Table ID) : Event ID = 3119

H−EIT : Event ID = 3127

H−EIT (Table ID) : Event ID = 311a H−EIT PF Min Sect Reptn Int : Event ID = 370f

Ind DVB EIT actual p/f min section RI : Event ID = 3733 H−EIT PF Max Subtable Reptn Int : Event ID = 3710

Ind DVB EIT actual p/f max subtable RI : Event ID = 3734

M−EIT : Event ID = 3128

M−EIT (Table ID) : Event ID = 311b M−EIT Max Subtable Reptn Int : Event ID = 375c M−EIT Min Sect Reptn Int : Event ID = 375d

L−EIT : Event ID = 3129

L−EIT (Table ID) : Event ID = 311c L−EIT Max Subtable Reptn Int : Event ID = 375e L−EIT Min Sect Reptn Int : Event ID = 375f

L−SDTT : Event ID = 312b

SDTT(L) min section RI : Event ID = 37ec

Ind SDTT(L) min section RI : Event ID = 37ee SDTT(L) max subtable RI : Event ID = 37ed

Ind SDTT(L) max subtable RI : Event ID = 37ef L−SDTT (Table ID) : Event ID = 311d

H−SDTT : Event ID = 312a

SDTT(H) min section RI : Event ID = 37e8

Ind SDTT(H) min section RI : Event ID = 37ea SDTT(H) max subtable RI : Event ID = 37e9

Ind SDTT(H) max subtable RI : Event ID = 37eb H−SDTT (Table ID) : Event ID = 311e

SIT : Event ID = 312d

SIT (Table ID) : Event ID = 311f

DIT : Event ID = 312c

DIT (Table ID) : Event ID = 3126

CDT : Event ID = 3777

CDT Min Sect Reptn Int : Event ID = 3775

Ind CDT min section RI : Event ID = 374e CDT Max Subtable Reptn Int : Event ID = 3776

Ind CDT max subtable RI : Event ID = 374d

BIT : Event ID = 3771

BIT Min Section Reptn Int : Event ID = 3762

Ind BIT min section RI : Event ID = 3743 BIT Max Subtable Reptn Int : Event ID = 3763

Ind BIT max subtable RI : Event ID = 3744 BIT (Table ID) : Event ID = 3781

PAT/PMT Consistency : Event ID = 3330 DSM−CC error : Event ID = 3910

DII min RI : Event ID = 3908

Ind DII min repetition error : Event ID = 3909 DII max RI : Event ID = 390c

MTM400A Test Parameter and Configuration File Technical Reference

1−19

Test Parameters - Standards Tests

Ind DII max repetition error : Event ID = 390d DII Timeout : Event ID = 3905 DII download completion : Event ID = 390e

Ind DII completition : Event ID = 390f

Miscellaneous : Event ID = 37f9

TS Availability : Event ID = 3053 PID Occupancy : Event ID = 2001

PID Test : PID Occupancy : Event ID = 2004

Prog Occupancy : Event ID = 2002

Progran occupancy error : Event ID = 3039 Program Test : Prog Occupancy : Event ID = 3039

PCR Overall Jitter (PCR_OJ) : Event ID = 3040

PID Test : PCR Overall Jitter (PCR_OJ) : Event ID = 3043

PCR Frequency Offset (PCR_FO) : Event ID = 3041

PID Test : PCR Frequency Offset (PCR_FO) : Event ID = 3044

PCR Drift Rate (PCR_DR) : Event ID = 3042

PID Test : PCR Drift Rate (PCR_DR) : Event ID = 3045

DPI/SIT Any Errors : Event ID = 382a

Multiple (>1) DPI/SIT PIDs per Program : Event ID = 3823 Excess (>8) DPI/SIT PIDs per Program : Event ID = 3824 DPI/SIT Encrypted Error : Event ID = 3825 DPI/SIT Missing : Event ID = 3826

Ind DPI/SIT Missing : Event ID = 3827 DPI/SIT Syntax : Event ID = 3828 DPI/SIT Max subtable RI : Event ID = 3829

DPI/SIT Any information events : Event ID = c01d

DPI/SIT Data : Event ID = c017 DPI/SIT Splice Cancel : Event ID = c018 DPI/SIT Splice : Event ID = c019 DPI/SIT Program Splice : Event ID = c01a DPI/SIT Component Splice : Event ID = c01b

PID Group Occupancy : Event ID = 2005

PID group occupancy error : Event ID = 2003

PID Bit Rate Variability : Event ID = 2010

PID Test : PID Bit Rate Variability : Event ID = 2011

Discontinuity : Event ID = 3131

PID Test : Discontinuity : Event ID = 3133

Transport Stream Occupancy : Event ID = 3600 Service Log Overflow : Event ID = 5200 Program Information : Event ID = c001 PTS/DTS Syntax Error : Event ID = 3054

Any Template Error : Event ID = 6fff

Template Header Error : Event ID = 6000

Template TransportStreamId error : Event ID = 6010 Template NetworkId error : Event ID = 6020 Template OriginalNetworkId error : Event ID = 6030 Template ServiceNumber error : Event ID = 6040

Any Template Service Error : Event ID = 6100

Any Template PID Error : Event ID = 6200

Template CADescriptorPresent error : Event ID = 6210 Template Pid scrambling error : Event ID = 6220

1−20

MTM400A Test Parameter and Configuration File Technical Reference

ISDB (Partial Reception)

Event ID = 37d0

Event ID = 37d1

Event ID = 37d2

Event ID = 37d3

Event ID = 37d4

Event ID = 37d5

Event ID = 37d6

Event ID = 37d7

Event ID = 37d8

Test Parameters - Standards Tests

Template StreamType error : Event ID = 6230 Template Pid constraint error : Event ID = 6240

Any Template Rating Error : Event ID = 6300

Template DVB/ATSC Ratings error : Event ID = 6301

ISDB Tests : Event ID = 37f8

ISDBT NIT Terrestrial Delivery Validation : Event ID = 37a1

ISDBT Mode/Guard Interval Validation : Event ID = 379e ISDBT Time Interleaving Validation : Event ID = 379f ISDBT Modulation/Error Compensation Validation : Event ID = 37a0

ISDBT Partial Reception/TS Information Consistency : Event ID = 37a3 ISDBT Guard Interval Consistency : Event ID = 379a ISDBT Transmission Mode Consistency : Event ID = 379b ISDBT Partial Reception Consistency : Event ID = 379c ISDBT Modulation Consistency : Event ID = 379d ISDBT NIT Service List Consistency : Event ID = 37a2 ISDBT EIT Type Content Check : Event ID = 37a5 ISDBT EIT Unique Event Id : Event ID = 37a6 ISDBT SDT/EIT Consistency : Event ID = 37a7

Ind ISDBT SDT/EIT Consistency : Event ID = 37a8 ISDBT NIT/EIT Consistency : Event ID = 37aa

Ind ISDBT NIT/EIT Consistency : Event ID = 37ab Ind ISDBT NIT/EIT Consistency : Event ID = 37ab ISDBT NIT/SDT Consistency : Event ID = 37b1 ISDBT TMCC Id Error : Event ID = 37c3 ISDBT Max Partial Reception Services Error : Event ID = 37c4 ISDBT NIT/PMT Consistency : Event ID = 37c5 ISDBT Partial Reception Service ID Check : Event ID = 37c6 HEIT Schedule : Event ID = 37fd