Tektronix DPO 70000, MSO70000 DATASHEET

Digital and Mixed Signal Oscilloscopes

DPO/DSA/MSO70000 Series Data Sheet

Pinpoint®Triggering – Minimize time spent trying to acquire problem signals for efﬁcient troubleshooting and shortened debug time

6.25 Gb/s Real-time Serial Trigger – Assures triggering on the ﬁrst instance of a speciﬁed NRZ or 8b/10b pattern to allow isolation of pattern-dependent effects

Search & Mark – Provides waveform pattern matching and software triggers for signals of interest

P7500 TriMode™ Probing System – Perfectly matched s ignal connectivity from 4 GHz to 20 GHz

Application Support for High-speed Serial Industry Standards, RF, Power Supplies, and Memory – Enables standard-speciﬁccertiﬁcation, measurement automation, and ease of use

Features & Beneﬁts

On All Four Channe ls Simultaneously

20, 16, 12 Up to 50 GS/s on Real-time Sample Rate Up to 250 Megasample Record Length with MultiView Zoom™ Feature for Quick Navigation Fastest Waveform Capture Rate with >300,000 wfms/s Maximum per Channel

Uncompromised Bandwidt h – Up to 20 GHz on all 4 channels enables measurement on the latest high-speed serial standards

Superio the truest representation of your waveform

Industry-leading Sam ple Rate and Timing Resolution

100 GS/s on 2 Channe ls (20, 16, and 12.5 GHz models)

16 Logic Channels with 80 ps Timing Resolution for Debug of Digital and Analog Signals (MSO70000 Series only)

.5, 8, 6, and 4 GHz Bandwidth Models

r Signal Integrity and Excellent Signal-to-Noise Ratio – Observe

P6780 and P6717 High-performance 17-channel Logic Probes with Bandwidths up to 2.5 GHz for Connections to Today's Fast Digital Signals (MSO70000 Series only)

Applications

Design Veriﬁcation including Signal Integrity, Jitter, and Timing Analysis

Design Characterization for High-speed, Sophisticated Designs

Certiﬁcation Testing of Serial Data Streams for Industry Standards

Memory Bus Analysis and Debug

Prototype Turn-on and Power Supply Veriﬁcation

Research and Investigation of Transient Phenomena

Production Testing of Complex Systems

Spectral Analysis of Transient or Wide-bandwidth RF Signals

Data Sheet

P7500 TriMode probes simplify complex measurement setups.

P6780 Differential Logic probes provide high-bandwidth connections for up to 16 digital signals.

Tools for Your Complete Design Cycle

Tektronix understands that engineers rely on an oscilloscope throughout their design cycle, from prototype turn-on to production testing. The DPO/DSA/MSO70000 Series oscilloscopes' unique capabilities combined

h exceptional signal acquisition performance and analysis accelerate

wit your measurement tasks.

Unmatched Acquisition and Signal-to-Noise Performance

The superior signal integrity and excellent signal-to-noise ratio of the DPO/DSA/MSO7 results.

High bandwidth, up to 20 GHz, matched across 4 channels

Bandwidth enhancement eliminates imperfections in frequency response all the way to the probe tip. The user-selectable ﬁlter for each channel prov representation of extremely fast signals. In addition, only Tektronix allows the user to disable the bandwidth enhancement for applications needing the

Simultaneous high sample ra te on all channels captures more signal details (transients, imperfections, fast edges)

100 GS/s on 2 channels and 50 GS/s on all analog channels for the

12.5, 16, and 20 GHz models 25 GS/s on all analog channels for the 4, 6, a nd 8 GHz models

12.5 GS/s on all logic channels in the MSO70000 Series

Lowest jitter noise ﬂoor and highest vertical accuracy provide additional margin in your measurements

Long record length provides high resolution and extended-duration waveform capture

Standard 10 MS per channel on the DPO70000 and MSO70000 Series and 31 MS on the DSA70000 Series Optional up to 125 MS on all four channels for the 4, 6, and 8 GHz models Optional up to 250 MS on all four channels for the 12.5, 16, and 20 GHz models On the MSO70000 Series, the record length of logic channels match the analog record lengths for uncompromised analog and digital acquisition MultiView Z oom helps you manage long records, compare and analyze multiple waveform segments

With h DPO/DSA/MSO70000 Series enable you to perform precise characterization measurem ents. When debugging a DUT, a low noise

and maximum signal ﬁdelity of the measurement instrument

ﬂoor allows you to ﬁnd the smallest anomalies that might affect the DUT's performance. For RF signals, a lower noise ﬂoor translates into a higher

amic range , opening the DPO/DSA/MSO70000 Series to a wider

dyn range of applications

Widest Range of Probing Solutions – Whether you need to measure 8 G b/s serial data, fast digital logic, or switching currents from your new power supply design, Tektronix offers a vast array of probing solutions, including

ive single-ended, differential, logic, high voltage, current, optical, and a

act wide range of probe and oscilloscope accessories.

0000 Series ensures conﬁdence in your measurement

ides magnitu de and ph ase correction for more accurate

highest measurement throughput

igh signal-to-noise ratio and low internal noise ﬂoor, the

2 www.tektronix.com

Digital and Mixed Signal Oscilloscopes — DPO/DSA/MSO70000 Series

Quick S election G uide

Model Analog Bandwidth

DPO70404B 4 GHz 25 GS/s 10 MS DSA70404B 4 GHz 25 GS/s 31 MS MSO70404 4 GHz 25 GS/s 10 MS DPO70604B 6 GHz 25 GS/s 10 MS DSA70604B 6 GHz 25 GS/s 31 MS MSO70604 6 GHz 25 GS/s 10 MS DPO70804B 8 GHz 25 GS/s 10 MS DSA70804B 8 GHz 25 GS/s 31 MS MSO70804 8 GHz 25 GS/s 10 MS DPO71254C 12.5 GHz 100 GS/s / 50 GS/s 10 MS DSA71254C 12.5 GHz 100 GS/s / 50 GS/s 31 MS MSO71254C 12.5 GHz 100 GS/s / 50 GS/s 10 MS DPO71604C 16 GHz 100 GS/s / 50 GS/s 10 MS DSA71604C 16 GHz 100 GS/s / 50 GS/s 31 MS MSO71604C 16 GHz 100 GS/s / 50 GS/s 10 MS DPO72004C 20 GHz 100 GS/s / 50 GS/s 10 MS DSA72004C 20 GHz 100 GS/s / 50 GS/s 31 MS MSO72004C 20 GHz 100 GS/s / 50 GS/s 10 MS

Analog Sample Rate

2/4 Channels

Standard Memory –

Analog + Digital

Analog Channels Logic Channels

4 4 416 4 4 416 4 4 416 4 4 416 4 4 416 4 4 416

System Turn-on and Veriﬁcation

Fromthetimeadesignisﬁrst powered up through the initial operational checks, the DPO/DSA/MSO70000 Series provide the features you need.

Uncompromised Four-channel Acquisition

With the industry's lowest noise and up to 50 GS/s sample rate on all four channels the DPO70000 Series ensures that signal integrity checks and timing analysis can be done without worrying about noise and jitter in th e scope distorting the measurements. Single-shot bandwidths up to 20 GHz on all four channels ensure that you'll capture your signals of

t without worrying about undersampling when using more than 1 or

interes 2 c h annels.

ications requiring the lowest internal noise and jitter, 100 GS/s

For appl performance further reduces noise and jitter and provides additional measurement head room.

16-channel Digital Acquisition (MSO70000 Series only)

When you have many interfaces to verify, the MSO70000 Series with 4 analog and 16 logic channels enables efﬁcient channel-to-channel timing checks. With timing resolution of 80 ps, the MSO70000 Series' digital

ion system enables you to make precise timing measurements on as

acquisit many as 20 chann els simultaneously.

iCapture – One Connection for Analog and Digital (MSO70000 Series only)

The number of signals that must be veriﬁed can often make the checkout of a design long and involved. By using the iCapture digital-to-analog multiplexer feature, you can easily verify the analog characteristics of any of the 16 signals connected to the MSO70000 Series' digital channels.

apture, you can quickly view the analog characteristics of any in put

Using iC channel. If the signal is working as expected, relegate it to a digital-only view and continue testing other lines.

www.tektronix.com 3

Data Sheet

Symbolic bu

s formats simplify identifying system states and setting up bus triggers.

Bus Decoding and Triggering (MSO70000 Series only)

Verifying your system operation often requires the ability to see speciﬁc system states on a key bus such as the DDR SDRAM interface. Th e MSO70000 Series includes parallel and low-speed serial bus decoding that provides deeper insight into the system's behavior. Using the bus triggering capability of the MSO70000 Series to isolate the exact state needed or ﬁnd invalid bu

s sequences is as easy as deﬁning the bus and choosing the bit

pattern or symbolic word that describes the desired state.

Deep Record Length Available on All Channels

Longer du

ration events such as power supply sequencing and system status words can b e analyzed without sacriﬁcing timing resolution u sing the long memory depths available on all four analog channels in the DPO/DSA70000 Series as well as the 16 logic channels of the MSO70000 Series. Optional memory depths up to 125 MS (Option 10XL) on the 4, 6, and 8 GHz models and 250 MS (Option 20XL) on the 12.5, 16, and 20 GHz models ar

e available.

Power supplies can be a critical failure point in any system. Careful testing

wer delivery system's power on sequence can be time consuming.

of the po The M SO70000 Series provides independent logic thresholds for each logic channel enabling multiple logic voltages to be set up and observed simultaneously for quick veriﬁcation of the system's power rails.

10 ms duration capture of synchronous high-speed and low-speed signals at 25 GS/s.

Protocol and Serial Pattern Triggering

To verify serial architectures, the serial pattern triggering for NRZ serial data streams with built-in c lock recovery in the DPO/DSA/MSO70000 Series allows correlating events across physical and link layers. The instruments can recover the clock signal, identify transitions, and allow you to set the desired encoded words for the serial pattern trigger to capture. This feature comes standard on the DSA70000 Series and is available on the DPO70000 and MSO70000 Series as Option ST6G. For higher bit rate standards like USB 3.0, the 8b10b serial pattern trigger and decode covers data rates up to 6.25 Gb/s.

Pattern lock triggering adds an extra dimension to NRZ serial pattern triggering by enabling the oscilloscope to take synchronized acquisitions of a long serial test pattern with outstanding time base accuracy. Pattern lock triggering can be used to remove random jitter from long serial data pat terns. Effects of speciﬁc bit transitions can be investigated, and

ng can be used with mask testing . Pattern lock triggering supports

averagi up to 6.25 Gb/s NRZ serial data streams and is standard on the DSA70000 Series instruments, or is included as part of Option ST6G on the DPO70000 and MSO700 00 Series.

4 www.tektronix.com

Digital and Mixed Signal Oscilloscopes — DPO/DSA/MSO70000 Series

System Characterization and Margin Testing

When a design is working correctly and the next task is to fully characterize its performance, the DSA70000 Series offers the industry's most comprehensive set of analysis and certiﬁcation tools, such as math expressions, waveform mask testing, pass/fail testing, event searching, and event marking process of making hundreds of characterization measurements.

Advanced Waveform Analysis

Full analysis of the power, voltage, and temperature corners of your system under test can be ve ry time consuming. The DPO/DSA/MSO70000 Series offer a wide range of built-in advanced waveform analysis tools.

Waveform cursors make it easy to measure trace-to-trace timing characteristics, while cursors that link between YT and XY display modes make it easy to investigate phase relationships and Safe Operating Area violations. Select f rom 53 automatic measurements using a graphical palette that logically organizes measurements into Amplitude, Time, Histogram, measurement results with statistical data such as mean, min, max, standard deviation, and population.

Deﬁne and a in terms that you can use. Access common waveform math functions with the touch of a button. Or, for advanced applications, create algebraic expressions consisting of live waveforms, reference waveforms, math functions, measurement values, scalars, and user-adjustable variables with an easy-to-use calculator-style editor.

With deep acquisition memory, margin testing can be done over many cycles and long duration trends in the data can be observed. Plus, data from the oscilloscope can be captured into Microsoft Excel using the unique Excel tool provided with the DPO/DSA/MSO70000 Series.

Automated Tools to Increase Measurement Throughput

Ease of use and measurement throughput are key when a large number of measurements must be completed with a performance oscilloscope.

. Tools for automation reduce the tedium and speed up the

and Communications categories. Gather further insight into your

pply math expressions to waveform data for on-screen re sults

bar, and formatted into custom reports using the Word toolbar

DPOJET Jit

concerns, highest se

ter and Eye Diagram Analysis – Simplify identifying signal integrity

jitter, and their related sources with DPOJET software. DPOJET provides the

nsitivity and accuracy available for real-time oscilloscopes.

The DSA70000 Series comes standard with the DPOJET Advanced Jitter and Eye Diagram measurem ent application, providing the tools you need to quickly perform a high volume of measurements and collect statistics. DPOJET Essentials is standard on the DPO70000 and MSO70000 Series wi

th the DPOJET advanced version available as an option. Application-speciﬁc measurement packages are also available that extend DPOJET and perform the extensive set of tests required by industry standard groups.

RF and Vector Signal Analysis

When vector signal analysis of RF or baseband signals are needed the optional SignalVu application enables measurements in multiple domains (frequency, time, phase, modulation) simultaneously. SignalVu measurements are fully correlated with the scope's time domain acquisition

gering. Time domain events, such as commands to a RF

and trig subsystem, can be used as trigger events, while the subsystem's RF signal can be seen in the freq uency domain.

www.tektronix.com 5

Data Sheet

TekExpres

USB 3.0 pro and receiv Universal selection selectio USB-TX le

3.0 solut

TekExpress SATA Automated Compliance Test Software – Complete support for SATA Gen1 and SATA Gen2 deﬁned test suites for transmitters and receivers. Reduce your compliance test time by approximately 70% with simple, efﬁcient automation of all required test suites with TekExpress software. Also included is auto-recognition of all required test equipment, precise DUT/Host control, and one-button testing.

s USB 3.0 Automated Test Software (Option USB-TX) – TekExpress

vides an automated, simple, and efﬁcient way to test USB 3.0 transmitter

er hosts and devices consistent with the requirements of the SuperSpeed

Serial Bus Electrical Compliance Test Speciﬁcation. The application automates

of appropriate CTLE and reference channel emulation ﬁlters and measurement

ns based on device type, test type, test points, and selected probes. In addition,

verages DPOJET allowing for debug and advanced characterization of USB

ions.

TekExpress® Software Automation Framework

ekExpress software automation framework has been developed for

The T automated o ne-button testing of high-sp eed serial data standards. Built on top of National Instruments TestStand product, TekExpress efﬁciently executes the required tests for many serial standards like SATA Rev 3.0,

SDLA - Serial Data Link Analysis (Option SLE and SLA) – Offers the capability to emulate the serial data channel, de-embed a ﬁxture or other network, and add or remove transmitter equalization. Option SLA adds processing of waveforms with FFE and DFE equalizations and automatic equalizer training. DPOJET provides advanced measurement and jitter analysis of the resulting waveforms.

USB 3.0, DisplayPort, and 10GBASE-T Ethernet. Run on an external Windows PC, the TekExpress SATA software orchestrates the instrument setup and control sequences to provide complete test results for complete design validation.

Beyond using the TekExpress framework, custom applications that you develop yourself using application development environments such as MATLAB

can further exten d the tool set of the DPO/DSA/MSO70000

Series.

Characterization measurements depend upon accuracy and repeatability. The wide bandwidth and unmatched signal ﬁdelity of the DPO/DSA/MSO70000 analog front end ensures that your signal quality measurements such as rise times are faithful and amplitude correct with ﬂatness of ±0.5 dB.

Custom Filter and De-embed Capability

ate your own ﬁlters or use the ﬁlters provided as standard with the

Cre DPO/DSA/MSO70000 Series to enhance your ability to isolate or remove a c omponent of your signal (noise or speciﬁc harmonics of the signal). These customizable FIR ﬁlters can be used to implement signal-processing techniques, such as removing signal pre-emphasis or minimizing the effects of ﬁxtures and cables connected to the device under test. Using the optional

ial Data Link Analysis (SDLA) application, you can gain further insight

Ser into serial data links with the capability to emulate the serial data channel from its S-parameters, de-embed the ﬁxture or other network, and add or remove transmitter equalization (de-emphasis/pre-emphasis).

6 www.tektronix.com

Digital and Mixed Signal Oscilloscopes — DPO/DSA/MSO70000 Series

Certiﬁcation

Beforeaproductcangotomarket,youoftenneedtocompleteaseriesof certiﬁcation tests on the industry-standard high-speed serial buses in your design. These tests can involve many hours of wrestling with test ﬁxtures, reading certiﬁ that your system passes the required tests.

Application-speciﬁc Solutions – Enable Standard-speciﬁcCertiﬁcation, Measurement Automation, and Extended Signal Analysis

Accurate, Simple, and Customizable Physical Layer Certiﬁcation Testing – For designers with industry-standard certiﬁcation needs, standard-speciﬁc compliance a mask and measurement limit testing are available as options on the DPO/DSA/MSO70000 Series. Modules are available for PCI Express DDR Memory, Serial ATA and SAS, InﬁniBand, HDMI, Ethernet, DisplayPort, DVI, UWB, MIPI USB.

See the following list for highlights of the available application-speciﬁc solutions.

cation documents, and collecting sufﬁcient data to validate

nd analysis modules that conﬁgure the pass/fail waveform

D-PHY and M-PHY, Power Supplies, and

USB 3.0 Transmitter Test Solution (Option USB3) – Perform veriﬁcation, characterization, and debug of USB 3.0 devices. Measurements are implemented in DPOJETandarecomplianttotheUSB3.0speciﬁcation. For compliance and automation, USB-TX is available.

DDR Memory Bus Analysis (Option DDRA) – Automatically identify DDR1, LPDDR1, LPDDR2, DDR2, DDR3, and GDDR3 Reads and Writes and makes JEDEC conformance measurements with pass/fail results on all edges in every Read and Write burst. DDRA provides capabilities for measurements of clock, address, and control signals. In addition to enabling conformance testing DDRA with DPOJET is the fastest way to debug complex memory signaling issues. DDRA can also use the Command/Address lines to trigger on speciﬁc read/write states when running on the MSO70000 Series Mixed Signal Oscilloscope, which offers 16 channels of digital logic probing.

PCI Express Analysis Test Solution (Option PCE) – Analyze the performance of your PCI Express Rev 1.0, 2.0, or 3.0 (draft spec) design with comprehensive test support. Using DPOJET, Option PCE enables tests that conform to PCI-SIG standards.

www.tektronix.com 7

Data Sheet

Ethernet Compliance Test Solution (Option ET3) – Receive full PHY layer support for Ethernet variants 10BASE-T, 100BASE-TX, and 1000BASE-T with the comprehensive, integrated Tektronix Ethernet tool set. Analog veriﬁcation, automated compliance software, and device characterization solutions are all included.

MIPI®D-PHY Debug, Analysis, Characterization, and Compliance Test Solution (Option D-PHY) –VerifytotheD-PHYspeciﬁcation by rapidly characterizing and

discovering sources of jitter and signal integrity concerns using the fully ﬂexible and customizable test setup. Using DPOJET, Option D-PHY enables transmitter high-speed data-clock timing measurements, along with a full range of electrical characteristics in high-speed or low-power modes.

MIPI®M-PHY Debug, Analysis, Characterization and Conformance Test Solution (Option M-PHY) –VerifytotheM-PHYspeciﬁcation by rapidly characterizing and

discovering sources of jitter and signal integrity concerns. Using DPOJET, Option M-PHY enables transmitter signaling and timing measurements such as differential transmit eye diagrams, rise and fall times, slew rate, amplitude parameters, common mode voltages on each lane for both the large and small amplitude conﬁgurations, as well as the terminated and unterminated cases.

XGbT 10GBASE-T Automated Compliance Software – Quickly perform 10GBASE-T measurements per the IEEE 802.3an-2006 standard including Power Spectral Density (PSD), Power Level, and Linearity, with a simpliﬁed instrument conﬁguration. XGbT provides ﬂexible control over test conﬁgurations and analysis parameters, enabling more in-depth device characterization.

8 www.tektronix.com

Digital and Mixed Signal Oscilloscopes — DPO/DSA/MSO70000 Series

DVI Compliance Test Solution (Option DVI) – Obtain quick and dependable results with the DVI compliance test software. Automated testing based on pass/fail detection dramatically enhances productivity.

DisplayPort Compliance Test Solution (Option DSPT) – Support DisplayPort Compliance Test Standard (CTS) source test with four-line simultaneous testing using the Tektronix P7300SMA Series probes and DisplayPort software. Detailed test reports with waveform plots, pass/fail results, and margin analysis are included.

HDMI Compliance Test Solution (Option HT3) – Fast, efﬁcient solution for HDMI compliance measurement challenges, no matter if you are working on a Source, Cable, or Sink solution. This application provides all the HDMI compliance test solutions you need to ensure quality and interoperability.

Ultra-Wideband Spectral Analysis Software (Option UWB) – Analyze hundreds of packets, TFC, and data-rate combinations. In addition, the automatic WiMedia modulation analysis conﬁguration will analyze how complex wideband signals change frequency and amplitude with time using real-time spectrograms spanning 20 GHz.

www.tektronix.com 9

Data Sheet

Power Measurement and Analysis Software (Option PWR) –Improvetheefﬁciency of switching power supplies with increased power densities. Measure and analyze power dissipation in power supply switching devices and magnetic components, and generate detailed test reports in customizable formats.

SignalVu® Vector Signal Analysis – Easily verify wide-bandwidth designs such as wideband radar, high data-rate satellite links, or frequency-hopping radios and characterize wideband spectral events. SignalVu combines the functionality of a vector signal analyzer, a spectrum analyzer, and the powerful triggering capabilities of the DPO/DSA/MSO70000 Series – all in a single package.

DSA70000 – A Dedicated Solution Conﬁgured for Today's High-speed Serial Design Challenges

The DSA70000 Digital Serial A nalyzers are specially conﬁgured to addre ss high-speed serial data designs by encapsulating many of the serial domain features neede d for high-speed serial veriﬁcation and characterization. These standard features on the DSA70000 Series are options on the DPO70000 and MSO70000 Series.

Communica

Serial Pattern Triggering – Real-time serial pattern triggering and protocol

tions Mask Testing.

decode with built-in clock recovery recovers the clock signal, identiﬁes the transitions, and decodes characters and other protocol data. You can see the 8b/10b bit sequences decoded into their words for convenient

, or you can set the desired encoded words for the serial pattern

analysis trigger to capture. With pattern lock triggering, the DSA70000 Series can synchronize to long serial te st patterns with data rates up to 6.25 Gb/s and remove random jitter.

DPOJET Ji

tter, Timing, and Eye Diagram Analysis –

The DSA70000 Series features th e highest-accuracy jitter and timing measurements as well as comprehensive analysis algorithms. Tight timing margins demand stable, low-jitter designs. You can make jitter measurements over contiguous clock cycles on every valid pulse in a single-shot acquisition. Multiple measurements and trend plots quickly show system timing under variable

ons, including Random and Deterministic Jitter separation.

conditi

Communications Mask Testing – Provides a complete portfolio of masks for

verifying compliance to serial communications standards. Over 150 masks for the following standards are supported – PCI Express, ITU-T/ANSI

Ethernet IEEE 802.3, ANSI X3.263, Sonet/SDH, Fibre Channel,

T1.102, InﬁniBand, USB, Serial ATA, Serial Attached SCSI, IEEE 1394b, RapidIO, OIF Standards, Open Base Station Architecture Initiative (OBSAI), Common Public Ra dio Interface (CPRI).

31 MS Rec

ord Length –

31 MS on all four channels provides a longer time sequence at high resolution. Optional record lengths up to 125 MS for the 4, 6, and 8 GHz mod els, 250 MS for the 12. 5, 16, and 20 GHz mo dels extend the acquisition time sequence.

With standard features that extend the functionality of the Tektronix DPO70000 Series to address high-speed serial signal analysis and certiﬁcation, th e DSA70000 Series offers a specialized instrument that efﬁciently addresses your design challenges.

10 www.tektronix.com

Digital and Mixed Signal Oscilloscopes — DPO/DSA/MSO70000 Series

DSA Feature Set in the MSO70000

If you need to combine the functiona lity of the DSA70000 and the MSO70000 Series, the DSA options for the MSO70000 Series provide the DSA's high-speed serial test features in an MSO (see Option DSAH or DSAU in the Orde

ring Information section below).

User-selectable Bandwidth Limit Filters

While wide bandwidth is needed to characterize your high-speed serial designs, certiﬁ cation testing can require a speciﬁc instrument bandwidth appropriate for the signal's data rate in order to correlate test results between diffe user-selectable bandwidth limiting ﬁlters. Using these bandwidth limit ﬁlters which range from 500 MHz to 19 G Hz, you will ensure that your measurement is done using the bandwidth speciﬁed by the industry standard.

rent test labs. The DPO/DSA/MSO70000 Series feature

Debugging

Throughout the design cycle, DPO/DSA/MSO70000 Series oscilloscopes provide the a cause. Using FastAcq's high waveform ca pture rate, you can quickly identify signal anomalies that occur intermittently – saving minutes, hours, or even days by quickly revealing the nature of faults so sophisticated trigger modes can be applied to isolate them. U sing Pinpoint triggers, infrequent events such as glitches or signal runts caused by bus contention or signal in

bility to debug malfunctioning subsystems and isolate the

tegrity issues can be captured, analyzed, and then eliminated.

B Event Scan identiﬁes speciﬁc events to build an eye diagram.

FastAcq – Expedites Debugging by Clearly Showing Imperfecti

More than just color grading or event scanning, FastAcq's proprietary DPX acquisiti per second on all four channels simultaneously, dramatically increasing the probability of discovering infrequent fau lt events. And with a simple turn of the intensity knob you can clearly “see a world others don't see”, displaying the complete picture of your circuit's operation. Some oscilloscope vendors claim high waveform capture rates for short bursts of time, but only DPO/DSA/M can deliver these fast waveform capture rates on a sustained basis.

ons

on technology captures signals at more than 300,000 waveforms

SO70000 Series oscilloscopes, enabled by DPX technology,

Pinpoint®Trigger

Whether you're trying to ﬁnd a problem signal or need to isolate a section of a complex signal for further analysis, like a DDR Read or Write burst,

x P inpoint triggering provides the solution. The Pinpoint trigger

Tekt r o n i system uses Silicon Germanium (SiGe) technology to provide very high trigger sensitivity with very low trigger jitter and the ability to capture very narrow glitches. Pinpoint triggering allows selection of virtually all trigger types on both A and B trigger events delivering the full suite of advanced trigger types for ﬁnding sequential trigger events. Pinpoint triggers provide

eset capabilities that begin the trigger sequence again after a

trigger r

Use B Event Scan trigger on DDR DQS edges used to construct an eye diagram of all bits in a burst.

speciﬁed time, state, or transition so that even events in the most complex signals can be captured. Other oscilloscopes typically offer less than 20 trigger com binations; Pinpoint triggering offers over 1400 combinations, all at full performance.

With Enhanced Triggering, trigger jitter is reduced to <100 fs. With this stability at the trigger point, the trigger point can be used as a measurement reference.

B Scan Event Trigger

Users who wish to create eye diagrams from data bursts synchronized or initiated by an A event will ﬁnd the B Event Scan trigger function especially useful. B Event Scan is an A to B trigger sequence that will trigger and capture burst event data of interest deﬁned by the B Event setu p menu. Captured bits can be scanned in a sequential or randomized fashion,

ively the trigger can toggle between two successive B trigger events.

alternat

www.tektronix.com 11

Data Sheet

Integrated Logic Channels – Provide time-correlated analog and digital visibility for system debugging.

Logic Pattern Triggering

Logic pattern triggering allows logic qualiﬁcation that controls when to look for the faults and ignore events that do not occur during the desired state. On the MSO70000 Series, up to 20-bit wide logic pattern triggering enhances the Pinpoint trigger capabilities by helping you isolate the s peciﬁc

tate and analog events that are causing system failure.

system s

Digital A then Analog B Triggering (MSO70000 Seri

Advanced triggering capabilities include Digital A then Analog B to help you to identif analog event such as a runt pulse to trigger the acquisition.

yaspeciﬁc digital pattern or system state and then wait for an

es only)

Integrated Logic C hannels (MSO70000 Series only)

The MSO70000 S oscilloscope with an additional 16 logic channels that can be u se d to provide system level context when the fault occurs. This context, such as an illegal system state or error, may be the clue that leads to the root cause. When other oscilloscopes require you to use a logic analyzer to see the digital data you need to solve your debugging challenge, the MSO70000 Series can effectively quickly and easily. With 80 ps timing resolution and channel-to-channel skews of as little as 160 ps, the integrated logic channels allow you to view and measure time-correlated d igital and analog data in the same display window.

eries extends the debug capabilities of a 4-channel

debug and verify many digital timing issues in the system more

iCapture (MSO70000 Series only)

When an anomaly is seen on digital lines, iCapture delivers new insight into the analog behavior of the digital signals. With iCapture, you can route any 4 of the 16 logic channels to the MSO70000 Series' analog acquisition system so th multiplexer circuitry provides simultaneous digital and analog views of signals without having to move the logic probe or double probe the circuit.

at these signals can be viewed in ﬁner detail. iCapture's unique

12 www.tektronix.com

Digital and Mixed Signal Oscilloscopes — DPO/DSA/MSO70000 Series

FastFrame

When the key events you are interested in are widely spaced in time, such as bursts of activity on a bus, FastFrame segmented memory feature on the DPO/DSA/MSO70000 Series enables you to capture the events of interest while

conserving acquisition memory. Using multiple trigger events, FastFrame captures and stores short bursts of signals and saves them as frames for later viewing and analysis. On the MSO70000 Se ries, FastFrame and bus or logic triggering enable you to capture your fastest, bursty signals on the analog channels at the highest sample rate while the logic channel trigger recognizes the bus cycle of interest. Capturing thousands of frames is possible, s

o long-term trends and changes in the bursting s ignal can be

analyzed.

Advanced Search and Mark

Probing – Analog And Digital

Often the biggest challenge in debugging a system is getting access to the required signals. Tektronix offers a wide array of probing solutions, including the P7500 TriMode probing system with bandwidths that are perfe ctly matched to the D

PO/DSA/MSO70000 Series. The P7500 TriMode probes allow you to switch among differential, single ended, and common-mode measurements without moving the probe from its connection points. The P7500 Series offers probes with performance from 4 GHz to 20 GHz and offers several low-cost solder tips with quick connection features that allow moving the probe to various solder points fast and easy.

On the MSO70000 Series, the P6780 and P6717 logic probes provide connectivity to low-speed and high-speed digital signals with low loading, small size, a

nd a range of accessories for soldering and browsing.

Advanced Search and Mark – Highlights important events, skips unimportant ones, and navigates between events of interest effortlessly.

Isolating the key event causing your system failure can often be a tedious task. With the Advanced Event Search and Mark feature examining data

lighting i mportant events, skipping the unimportant ones, and

and high enhancing the comprehension of event relationships is made easy. With ASM, you'll be able to navigate between the events of interest effortlessly and uncover that rare event you ha ve been trying to ﬁnd.

Embedded Serial Bus (I2C, SPI) Decoding and Triggering (MSO70000 Series only)

The MSO70000 Series instruments provide I2C and SPI serial bus decoding and bus triggering that enable you to monitor or debug subsystems

ponents, such as frequency synthesizers, D/A converters,

and com and Flash Memory that are controlled or monitored using I

CorSPI serial buses. While monitoring or debugging these serial buses alone is relatively easy, decoding events on the serial bus can also enable more complex system-level debugging. When you experience an issue with a higher-speed serial interface, the clue to what is going wrong may be found

ng the serial bus decode feature to observe the data on your I

by usi

Cor

SPI int erface.

The low-cost solder tips available for the P7500 TriMode probes allow quick connection so moving the probe to various solder points is f ast and easy.

Solder tip accessories designed for the P6780 differential logic probes provide access to signals on tightly spaced vias and ﬁne-pitched components.

www.tektronix.com 13

Data Sheet

Production Testing

In addition to assisting engineers with design tasks, the DPO/DSA/MSO70 to test analog and digital signals with a wide range of clock speeds and data rates. Rackmount options are available for mounting the DPO/DSA/MSO70000 Series into an EIA standard 19 inch (487 mm) rack. An IEEE 488.2 standard GPIB interface is standard on all models.

OpenChoice®A

The OpenChoice Software allows you to customize your test and measurement system with familiar analysis tools. The analysis and networking features of the OpenChoice software add more ﬂexibility to Tektronix DPO/DSA/MSO70000 Series oscilloscopes: Using the fast embedded bus, waveform data can be moved directly from acquisition to analysis app conventional GPIB transfers.

Implementation by Tektronix of industry-standard protocols, such as TekVISA™ interface and ActiveX controls, are included for using and enhancing Windows applications for data analysis and documentation. IVI instrument drivers are included to enable easy communication with the oscillosco running on the instrument or an external PC. Or, use the Software Developer's Kit (SDK) to help create custom software to automate multistep processes in waveform collection and analysis with Visual BASIC, C, C++, MATLAB, LabVIEW, LabWindows/CVI, and oth er common Application Development Environments. Integration of the oscilloscope with external PCs and non-

000 Series can provide test engineers with the ability

nalysis Tools

lications on the Windows desktop at much faster speeds than

pe using GPIB, RS-232, and L AN connections from programs

Windows hosts is also supported.

Research

With industry-leading acquisition speed and signal-to-noise ratio performance, the DPO/DSA/MSO70000 Series can provide researchers with tools that allow them to capture, display, and analyze high-speed and transient sign

Full Control o

You have full control of the instrument's acquisition modes. Choose the mode you need t Rate, or Manual settings. When you are doing signal exploration and want a lively signal, the default Automatic mode provides you with the liveliest display update rate. If you want the highest real-time sample rate that will give you the most measurement accuracy, then the Constant Sample Rate mode is for you. It will maintain the highest sample rate and provide the best real independent control of the sample rate and record length for applications requiring speciﬁc settings.

TekLink®

When you need to captu re a large number of signals simultaneously, TekLink allows you to synchronize multiple DPO/DSA/MSO70000 Series oscilloscopes and acquire more than four analog channels. TekLink enables synchronized capture on up to 4 oscilloscopes with one trigger event.

Document Tools

The OpenChoice architectu re provides a comprehensive s oftware infrastructure for faster, more versatile operations. Data transfer utilities, such as the Excel or Word toolbar plug-ins can be used to simplify analysis and documen

als with unmatched precision.

f Acquisition and Display Parameters

o do your job the fastest: Automatic, Constant Sample

-time resolution. Finally the Manual mode ensures direct and

tation on the Windows desktop or on an external PC.

14 www.tektronix.com

Digital and Mixed Signal Oscilloscopes — DPO/DSA/MSO70000 Series

This view in the ﬂoating license system identiﬁes the license's current user and location allowing you to easily manage your ﬂoating license inventory.

Unmatched Usability

The D PO/DSA/MSO70000 Series instruments excel in usability with a suite of productivity features, such as a touch screen, ﬂat menu structures, intuitive graphical icons, k nob -per-channel vertical controls, right clicks, mouse wheel operation, and familiar Windows-based controls.

Remote Desktop

When your oscilloscope is connected to a network, use the Windows Remote Desktop utility to access your o across the globe.

MyScope®– Create Your Own Control Windows

Easily create your own personalized "toolbox" of oscilloscope features in a matter of minutes using a simple, visual, drag-and-drop process.

scilloscope from across the lab or

Once created, these custom control windows a re easily accessed through a dedicated MyScope button a nd menu selection on the oscilloscope button/menu ba unlimited number of custom control windows, enabling each person who uses the oscilloscope in a shared environment to have their own unique control w indow. MyScope control windows w ill beneﬁt all oscilloscope users, eliminating the ramp-up time that many face when returning to the lab after not using an oscilloscope for a while, and enables the power user to be far more efﬁci than navigating through multiple menus to repeat similar tasks.

r, just like any other control window. You can make an

ent. Everything you need is found in one control window rather

Option Asset Management: Floating or Fixed

Many Tektronix application solutions and hardware options are enabled with an encrypted license key that is entered through the oscilloscope's Utilities me applied to a speciﬁc scope serial number and is permanently enabled. A ﬁxed license cannot be moved from one oscilloscope to another.

The second option is a ﬂoating license. Floating licenses provide the capability to move a license-key enabled option from one oscilloscope to another. This capability helps users with distributed teams and several Tektronix DPO/DSA/MSO70000 or DPO7000 Series oscilloscopes to better manage their assets and deploy applications or other options such as extended me

Managing and deploying ﬂoating licenses uses an easy online licensing management maintained on Tektronix secure servers and no infrastructure or your company IT department involvement is necessary. Simply utilize your myTek account to access, track, and deploy your oscilloscope ﬂoating-license enabled options.

nu. You now have two options. The ﬁrst option is a ﬁxed license

mory to the oscilloscope where it is needed.

system. All ﬂoating license management functions are

www.tektronix.com 15

Data Sheet

Characteristics

Vertical System

Characteristic DPO70404B

Bandwidth

DSA70404B

MSO70404

4 GHz 6 GHz 8 GHz 12.5 GHz 16 GHz 20 GHz

DPO70604B DSA70604B

MSO70604

DPO70804B DSA70804B

MSO70804

DPO71254C DSA71254C MSO71254C

(User-selectable DSP enhance)

Hardware Analog

4 GHz 6 GHz 8 GHz 12.5 GHz 16 GHz (typical) 16 GHz (typical)

Bandwidth (–3 dB) Input Channels Logic Channels

444444

16 16 16 16 16 16 (MSO70000 Series only)

Rise Time 10% to 90%

98 ps 65 ps 49 ps 32 ps 24.5 ps 18 ps

(Typical) Rise Time 20% to 80%

68 ps 45 ps 34 ps 22 ps 17 ps 14 ps

(Typical) Vertical Noise (% of full

scale) (Typical)*

width Limits

Band

0.28% 0.32% 0.35% 0.36% 0.42% 0.59%

Dependingoninstrumentmodel: 19GHz,18GHz,17GHz,16GHz,15GHz,14GHz,13GHz,12GHz,11GHz,10GHz,

9GHz,8GHz,7GHz,6GHz,5GHz,4GHz,3GHz,2GHz,1GHz,or500MHz

Channel-to-Channel Isolation (Any two

≥120:1 (for input frequency 0 to 10 GHz) ≥80:1 (for input frequency >10 GHz to 12 GHz)

≥50:1 (for input frequency >12 GHz to 15 GHz) ≥25:1 (for input frequency >15 GHz)

channels at equal vertical scale settings)

DC Gain Accuracy ±2% (of reading) Delay between Any

≤10 ps for any two channels with equal V/div and coupling settings

Two Channels (Typical) Effective Number of

5.5 bits*

Bits (Typical) Input Coupling DC (50 Ω), GND Input Impedance

50 Ω ±2%, 1 MΩ with TCA-1MEG adapter

Input Sensitivity

18 GHz and below 10 mV/div to 500 mV/div (100 mV to 5 V full scale) 20 GHz and 19 GHz 20 to 500 mV/div (200 mV to 5 V full scale)

Max Input Voltage, 50 Ω

Offset Accuracy

<5.0 V

for ≥100 mV/div; also determined by TekConnect accessory 1.0 V

RMS

±(0.35% (offset value-position) + 1.5 mV + 1% of full scale)

10 mV/div –

99.5 mV/div 100 mV/div –

±(0.35% (offset value-position) + 7.5 mV + 1% of full scale)

500 mV/div. Offset Range 10 mV/div: ±450 mV

20 mV/div: ±400 mV 50 mV/div: ±250 mV

100 mV/div: ±2.0 V 200 mV/div: ±1.5 V 500 mV/div: ±0.0 V

Passband Flatness (20,

±0.5 dB to 50% of nominal bandwidth at 25 °C 50, 100, 250 mV/div) (Typical)

Position Range ±5 div Vertical Resolution

*150 mV/div, bandwidth ﬁlter on.

50 mV/div, bandwidth ﬁlter on, max bandwidth up to 13 GHz, max sample rate.

8 bit (11 bit with averaging)

DPO71604C DSA71604C MSO71604C

for <100 mV/div

RMS

DPO72004C DSA72004C MSO72004C

16 www.tektronix.com

Digital and Mixed Signal Oscilloscopes — DPO/DSA/MSO70000 Series

Logic Channels (MSO70000 Series only)

Characteristic MSO70404 MSO70604 MSO70804 MSO71254C MSO71604C MSO72004C

Input Channels Trigger Clock/Qualiﬁer

Input Analog Bandwidth

With P6780 logic probe

With P6717 logic probe

Input Impedance

With P6780 logic

20 kΩ to ground per side or 40 kΩ differential mode ± 2.0%, 0.5 pF

probe With P6717 logic

20 kΩ ±1.0%,3pF

probe Vertical Resolution 1 bit Threshold Levels Threshold Accuracy

One per c

±75 mV + 3 Threshold Resolution 5 mV Logic Threshold Range

With P6780 logic probe

With P6717 logic probe

Minimum Voltage Swing

mum Input Voltage

Maxi

2.5 GHz

350 MHz

hannel, independently set

% of threshold setting

–2 to +4.5V

–1.5 to +4.0V

300 mV

p-p

nondestruct

±15 V

Horizontal Time Base System

acteristic

Char

Time Base Range Time Resolution (in

DPO7 DSA7

MSO7

0404B 0404B

0404

0604B

DPO7

0604B

DSA7

0604

MSO7

20 ps/div to 1000 s/div 10 ps/div to 1000 s/div

200 fs 100 fs

DPO7 DSA7

MSO7

0804B 0804B

0804

ET/IT mode) Channel-to-Channel

Range ±75 ns

Deskew Delta Time

1.48 ps 1.33 ps 1.24 ps 1.23 ps 1.15 ps 1.43 ps Measurement Accuracy RMS over <100 ns Duration; Single Shot; with Signal Rise Time = 1.2 × ScopeRiseTime*

Jitter Noise Floor

450 fs 450 fs 450 fs 300 fs 300 fs 400 fs (Typical) (With BW bandwidth enhance enabled)

Time Base Accuracy ±1.5 ppm initial accuracy, aging <1 ppm per year Time Base Delay Time

–5.0 ks to 1.0 ks

Range TriggerJitter(RMS) 1ps

*3100 mV/div, bandwidth ﬁlter ON, max sample rate.

(typical) with enhanced triggering OFF

RMS

<100 fs

with enhanced triggering O N

RMS

DPO7 DSA7 MSO7

1254C 1254C

1254C

DPO7 DSA7 MSO7

1604C 1604C 1604C

DPO7 DSA7 MSO7

2004C 2004C 2004C

www.tektronix.com 17

Data Sheet

Acquisition System

Characteristic DPO70404B

DSA70404B

MSO70404

Sample Rates

Real-time Mode 1,

DPO70604B DSA70604B

MSO70604

DPO70804B DSA70804B

MSO70804

DPO71254C DSA71254C MSO71254C

DPO71604C DSA71604C MSO71604C

100 GS/s

2 Channel (Max) Real-timeMode1,2,3,

25 GS/s 50 GS/s

or 4 Channel (Max) ET/IT Mode (Max) 5 TS/s 10 TS/s

Maximum R

With Standard Conﬁguration

With Record Length

ecord Length per Channel

10M on a ll four channels (DPO70000 and MSO70000 Series)

31.25M on all four channels (DSA70000 Series only)

31.25M on all four channels (DPO70000 and MSO70000 Series)

Option 2XL With Record Length

62.5M on all four channels

Option 5XL With Record Length

125M on all four channels

Option 10XL With Record Length

N/A 250M on all four channels

Option 20XL

Maximum Duration at Highest Real-time Resolution

ing Resolution

Tim

Duration with

Max

ndard Memory

Sta Max Duration with

0.4 ms DPO70000 and MSO70000 Series

1.25 ms (DPO70000 and MSO70000 Series) 0.31 ms (DPO70000 and MSO70000 Series)

40 ps (25 GS/s) 10 ps (100 GS/s)

0.1 ms DPO70000 and MSO70000 Series

1.25 ms for DSA70000 Series

0.31 ms for DSA70000 Series

Option 2XL Max Duration with

2.5 ms 0.63 ms

Option 5XL Max Duration with

5.0 ms 1.3 ms

Option 10XL Max Duration with

N/A

2.5 ms

Option 20XL

DPO72004C DSA72004C MSO72004C

Logic Channels (MSO70000 Series only)

Characteristic MSO70404 MSO70604 MSO70804 MSO71254C MSO71604C MSO72004C

SampleRate–All Channels (Max)

Timing Resolution 80 ps Displayed

Channel-to-Channel Timing Uncertainty

Maximum Record

125M on all channels (Option 10XL) 250M on all channels (Option 20XL)

Length per Channel Minimum Detectable

Pulse Width Maximum Number of

Buses Number of Channels

Up to 24 (16 logic, 4 analog, 4 math)

per Bus

12.5 GS/s

<160 ps

<400 ps

18 www.tektronix.com

Digital and Mixed Signal Oscilloscopes — DPO/DSA/MSO70000 Series

Acquisition Modes

Mode Description

Averaging Envelope FastAcq Maximum FastAcq Waveform Capture Rate >300,000 wfms/s on all 4 channels simultaneously FastFrame™

Hi-Res Real-time boxcar averaging reduces random noise and increases resolution Peak Detect Roll Mode

Sample Waveform Database Accumulates waveform database providing three-dimensional array of amplitude, time, and counts

From2to10,000waveformsincludedinaverage

From 1 to 2×10 FastAcq optimizes the instrument for analysis of dynamic signals and capture of infrequent events

Acquisition memory divided into segments; maximum trigger rate >310,000 waveforms per second. Time of arrival recorded with each event. Frame ﬁnder tool helps to visually identify transients

Captures and displays narrow glitches at all real-time sampling rates: 1 ns at ≤125 MS/s; 1/sample rate at ≥250 MS/s Scrolls sequential waveform points across the display in a right-to-left rolling motion. Works at sa mple rates up to

10 MS/s with a maximum record length of 40 MS Acquires and displays sampled values

waveforms included in min-max envelope

www.tektronix.com 19

Data Sheet

Pinpoint®Trigg er Syst em

Sensitivity DPO and MSO Models DSA Models

Internal DC Coupled 4% of full scale from DC to 50 MHz

External (Auxiliary Input) 50 Ω 250 mV from DC to 50 MHz, increasing to 350 mV at 1.0 GHz

Trigger Characteristics

A Event and Delayed B Event Trigger Types

Edge, Glitch, Runt, Width, Transition Time, Timeout, Pattern, State, Setup/Hold, Window – all except

Edge, Pattern, and State can be Logic State qualiﬁed by up to two channels Main Trigger Modes Trigger Sequences Main, Delayed by Time, Delayed by Events, Reset by Time, Reset by State, Reset by Transition. All sequences

can include separate horizontal delay after the trigger event to position the acquisition window in time Clock Recovery System Requires Option ST6G or Option MTH Standard Clock Recovery Phase Locked Loop Bandwidth Fixed at FBaud/1600 Clock Recovery Frequency Range 1.5 MBaud to 3.125 GBaud 8b10b Max Baud Rate

Requires Option ST6G Standard

Requires Option MTH StandardCommunications-related Triggers

Support for AMI, HDB3, BnZS, CMI, MLT3, and NRZ encoded communications signals. Select among isolated

positive or negative one, zero pulse form, or eye patterns as applicable to the standard

Serial Pattern Trigger

Requires Option ST6G Standard

Up to 64 bit serial word recognizer, bits speciﬁed in binary (high, low, don't care) or hex format.

Trigger on NRZ-encoded data up to 1.25 GBaud

Trigger on 8b/10b-encoded data from 1.25 to 6.25 GBaud (40 bits)

Threshold Range

P6780 –2 to +4.5 V

P6717 –1.5 to +4 V Threshold Accuracy Maximum I2C, SPI Bus Toggle Rate Clock Recovery Jitter (RMS) <0.25% bit period + 2 ps

<0.25% bit period + 1.5 ps

Enhanced Triggering

User-selectable; enhanced triggering corrects the difference in timing between the trigger

path and the acquired data path (supports all Pinpoint trigger types on both A- and B-Events

except pattern trigger); Not available in FastAcq mode

Line

Trigger on power line signal. Level ﬁxed at 0 V

Minimum Signal Amplitude needed for Clock Recovery 1 div

Tracking/Acquisition Range ±2% of requested baud Trigger Coupling DC, AC (attenuates <100 Hz)

Trigger Holdoff Range Trigger Level Range Internal

10% of full scale at 4 GHz 20% of full scale at 8 GHz

50% of full scale at 11 GHz

Auto, Normal, and Single

6.25 GBaud

±100 mV + 3% of threshold setting

10 MHz

for PRBS data patterns

RMS

for repeating "0011” data pattern

RMS

up to 1.25 Gbaud

p-p

1.5 div

above 1.25 Gbaud

p-p

HF Rej (attenuates >20 kHz)

LF Rej (attenuates <200 kHz)

Noise Reject (reduces sensitivity)

250 ns min to 12 s max

±120% of full scale from center of screen

20 www.tektronix.com

Trigger Modes

Mode Analog

Comm

Bus X X Edge X X

B Event Scan

Glitch

Pattern X X

Runt X

Serial Pattern

Setup/Hold State

Timeout X X Transition X Trigger Delay by

Events Trigger Delay by

Time Width X X

Window X

Channels

X XX

X X 1 to 2 billion events

X X 3.2 ns to 3 million seconds

MSO Logic

Channels

Digital and Mixed Signal Oscilloscopes — DPO/DSA/MSO70000 Series

Description

Standard feature on the DSA70000 Series, provided as part of Option MTH on the DPO70000 and MSO70000

Trigger on a parallel, I

B Event Scan is an A to B trigger sequence that will trigger and capture burst event data of interest as deﬁned in the B Event Scan setup menu. Captured bits can be scanned in a sequential or randomized

fashion, and alternatively the trigger can toggle between two successive B trigger events. Eye diagrams

Trigger on NRZ-encoded data up to 6.25 Gbaud; above 1.25 Gbaud requires 8b/10b encoded data. Extended

with pattern lock triggering to capture repeated acquisitions of long serial test patterns up to 6.25 Gb/s

Trigger on violations of both setup time and hold time between clock and data present on any two input channels

Any logical pattern of channels (1, 2, 3) (and 16 logic channels on the MSO70000 Series) clocked

Trigger on an event which remains high, low, or either, for a speciﬁed time period. Selectable from 300 ps

Trigger on pulse edge rates that are faster or slower than speciﬁed. Slope may be positive, negative, or either

Trigger on width of positive or negative pulse either within or out of selectable time limits (down to 150 ps)

Series. Support for AMI, HDB3, BnZS, CMI, MLT3, and NRZ encoded signals

Positive or negative slope on any channel or front-panel auxiliary input. Coupling includes

can be constructed with burst data acquired as a result of scanning B Event

Trigger on or reject glitches of positive, negative, or either polarity. Minimum glitch width

Trigger when pattern goes false or stays true for speciﬁed period of time. Pattern (AND, OR,

NAND, NOR) speciﬁed for four input channels (and 16 logic channels on the MSO70000

Trigger on a pulse that crosses one threshold but fails to cross a second threshold before

Trigger on an event that enters or exits a window deﬁned by two user-adjustable thresholds.

C, or SPI bus when the speciﬁc bus value is found. (MSO70000 Series only)

DC, AC, noise reject, HF reject, and LF reject

is 150 ps (typical) with rearm time of 300 ps

Series) deﬁned as high, low, or don't care

crossing the ﬁrst again. Event can be time- or logic-qualiﬁed

by edge on channel 4. Trigger on rising or falling clock edge

Event can be time or logic qualiﬁed

Search and Mark Events

Mark any events and document waveforms. Search positive/negative slopes or both on any channels.

Search glitches or runts, as well as transition rate, pulse width, setup and hold, timeout, window violations, or ﬁnd any logic or state pattern on any number of channels. Search DDR Read or Write bursts with Option DDRA.

Event table summarizes all found events. All events are time stamped in reference to trigger position. Users can choose to stop acquisitions when an event is found.

Waveform Analysis

Waveform Measurements

Measurement Description

Automatic Measurements

Amplitude Related Amplitude, High, Low, Maximum, Minimum,

Combination Area, Cycle Area, Phase, Burst Width Eye-pattern Related

Histogram Related

Time Related Rise Time, Fall Time, Positive Width, Negative Width,

53, of which 8 can be displayed on-screen at any one time; measurement statistics, user-deﬁnable reference levels, measurement within gates isolating the speciﬁc occurrence within an acquisition to measure

Peak-to-Peak, Mean, Cycle Mean, RMS, Cycle RMS, Positive Overshoot, Negative Overshoot

Extinction Ratio (absolute, %, dB), Eye Height, Eye Width, Eye Top, Eye Base, Crossing %, Jitter (p-p, RMS, 6sigma), Noise (p-p, RMS), Signal/Noise Ratio, Cycle Distortion, Q-Factor

Waveform Count, Hits in Box, Peak Hits, Median, Maximum, Minimum, Peak-to-Peak, Mean (μ), Standard Deviation (sigma), μ+1sigma, μ+2sigma, μ+3sigma

Positive Duty Cycle, Negative Duty Cycle, Period, Frequency, Delay

www.tektronix.com 21

Data Sheet

Bus Decoding (MSO70000 Series only)

Characteristic

Parallel

Description

Data from selected channels is grouped as a parallel, multichannel bus and displayed as a single bus value. Display can be binary, hexadecimal, or symbolic formats

I2C SCLK and SDA channels are displayed as a bus per the

Inter-Integrated Circuit speciﬁcation

SPI MOSI, MISO, SCLK, and SS channels are displayed as a

bus per the Serial Peripheral Interface speciﬁcation

Waveform Processing/Math

Measurement Description

Algebraic Expressions

Deﬁne extensive algebraic expressions including Waveforms, Scalars, User-adjustable Variables, and Results of Parametric Measurements

e.g. (Integral (CH1 – Mean(CH1)) × 1.414 × VAR1) Arithmetic Filtering Functions

Add, Subtract, Multiply, Divide Waveforms and Scalars

User-deﬁnable ﬁlters. Users specify a ﬁle containing the

coefﬁcients of the ﬁlter. Several example ﬁlter ﬁles are

provided Frequency Domain

Functions Mask Function

Spectral Magnitude and Phase, Real and Imaginary

Spectra

Generates a Waveform Database pixmap from a sample

waveform. Sample count can be deﬁned

Functions

Math

Average, Invert, Integrate, Differentiate, Square Root,

Exponential, Log 10, Log e, Abs, Ceiling, Floor, Min,

Max, Sin, Cos, Tan, ASin, ACos, ATan, Sinh, Cosh, Tanh Relational

Boolean result of comparison >, <, ≥, ≤, ==, != Vertical Units Magnitude: Linear, dB, dBm

Phase: Degrees, radians, group delay

IRE and mV units Window Functions Rectangular, Ham ming, Hanning, Kaiser-Bessel,

Blackman-Harris, Gaussian, Flattop2, Tek Exponential

Display, Computer, I/O

Computer System and Peripherals

Characteristic DPO/DSA70 000B

Models

DPO/DSA/MSO70000C

Models

Operating System Microsoft Windows XP Embedded CPU

PC System Mem

ory

Intel Pentium 4 Processor,

3.4 GHz 2GB 8GB

Intel Core 2 Duo

Processor, 3 GHz

Hard Disk Drive Rear-panel, removable hard disk drive,

160 GB capacity CD/DVD Drive Front-panel CD-R/W, DVD-R drive Mouse Keyboard

Optical wheel mouse, USB interface

USB interface

Input/Output Ports

Front Panel

Port

ger Input

Aux Trig DC Probe Calibration

Output Fast Edge Output SMA connector provides fast edge signal. 1 kHz

Recovered Clock SMA connector, ≤1.25 Gb/s, Output swing ≥130 mV

vered Data

Reco

USB 2.0 Port Allows connection of USB keyboard, mouse,

DPO/DSA70000B

Models

DPO/DSA/MSO70000C

Models

See trigger speciﬁcations

BNC connector, ±10 V DC for DC probe calibration

(signal available only during probe calibration)

±20%; 810 mV (base to top) ±20% into ≥10 kΩ

load; 440 mV ±20% into a 50 Ω load

into 50 Ω at 1.25 Gb/s. Requires Option ST6G or

Option MTH to enable on DPO70000 and MSO70000

Series, standard on DSA70000 Series

SMA connector, ≤1.25 Gb/s, Output swing of

1010 repeating pattern 200 mV into 50 Ω at

1.25 Gb/s. Requires Option ST6G or Option MTH to enable on DPO70000 and MSO70000 Series,

standard on DSA70000 Series

or storage device

p-p

Display

Characteristic

Description

Color Palettes Normal, Green, Gray, Temperature, Spectral, and

User-deﬁned

Display Format YT, XY Display Resolution

XGA 1024 horizontal × 768 vertical pixels Display Size Diagonal: 307.3 mm (12.1 in.) Display Type Liquid-crystal active-matrix color display Horizontal Divisions 10 Vertical Divisions 10 Waveform Styles Vectors, Dots, Variable Persistance, Inﬁnite Persistance

22 www.tektronix.com

Digital and Mixed Signal Oscilloscopes — DPO/DSA/MSO70000 Series

Rear Panel

Port

Audio Ports

DPO/DSA70000B

Models

DPO/DSA/MSO70000C

Models

Miniature phone jacks for stereo microphone

input and stereo line output

Aux Trigger Output BNC connector, 0 to 3 V; default output is

A-Event Trigger low true

External Time Base Reference In

BNC connector; allows time base system to phase lock to external 10/100 MHz reference. Optimized

(by using a software switch) for either a highly

stable clock or tracking mode GPIB Port Keyboard Port LAN Port

RJ-45 connector, supports 10BASE-T, 100BASE-T,

IEEE 488.2 standard

PS/2 compatible

and 1000BASE-T

Mouse Port

PS/2 compatible Parallel Port IEEE 1284, DB-25 connector eSATA port N/A External SATA interface

for eSATA storage devices

Power

External Video Ports

100 to 240 V

<870 W, 400 Hz; CAT II, <1100 VA typical

Connect to show the oscilloscope display, including

,±10%,50/60Hz;115V

RMS

±10%,

live waveforms on an external monitor or projector.

The primary Windows desktop can also be displayed

on an external monitor using these ports

Scope XGA Video Port

15-pin D-sub connector

N/A

on the rear panel, video is

IBM XGA compatible

DVI-I Video Port

N/A DVI connector, female.

DVI to VGA 15-pin

D-sub connector adapter

provided Serial Port DB-9 COM1 port Two DB-9 COM1 ports TekLink® Synchronizes multiple Tektronix oscilloscopes

together to allow simultaneous acquisition of

more than four channels

Time Base Reference Out BNC connector; provides TTL-compatible output

of internal 10 MHz reference oscillator

USB 2.0 Ports Four. Allow connection of USB keyboard,

mouse, or storage device

Windows Video Port 15-pin D-sub connector on

the rear panel; connects a second monitor to use

dual-monitor display

mode allowing analysis

results and plots to be

Alternatively, the DVI-I port can be conﬁgured to show the secondary Windows desktop (also

called extended desktop

or dual-monitor display)

viewed along with the

oscilloscope display.

Video is DDC2B compliant

Physical Characteristics

Dimensions

Benchtop Conﬁguration

Dimension

Height 298 11.74 Width 451 17.75 Depth 489.97 19.29

Weight kg lb.

Net 24 53 Shipping

Rackmount Conﬁguration

Dimension mm in.

Height 311 12.25 Width 480.1 18.9 Depth (from rack mounting

ear to back of instrument)

Weight kg lb.

Net 22 59 Kit 2.7 6

Mechanical

Cooling – Required Clearance

Top 0 0 Bottom 0 0 Left Side Right Side Front 0 0 Rear 0 0

Environmental

Characteristic

Description

Temperature

Operating 5 °C to +45 °C Nonoperating

–20°Cto+60°C

Humidity

Operating 8% to 80% relative humidity (RH) at up to 32 °C

Above +32 °C up to +45 °C; as limited by a 29.4 °C wet bulb temperature

Nonoperating

5% to 95% relative humidity (RH) Above +32 °C up to +60 °C; as limited by a 29.4 °C wet bulb temperature

Altitude

Operating 3,000 m (9,843 ft.) Nonoperating

12,000 m (39,370 ft.)

Regulatory

Electromagnetic

2004/108/EC; EN 61326-2-1:2006

Compatibility Certiﬁcations UL 61010-1, CSA 61010-1-04, LVD 2006/95/EC,

EN61010-1, IEC 61010-1

in.

34 67

546.1 21.5

in.

76 3 76 3

www.tektronix.com 23

Data Sheet

Ordering Information

Models

Model Description

MSO70404 4 GHz Mixed Signal Oscilloscope MSO70604 6 GHz Mixed Signal Oscilloscope MSO70804 8 GHz Mixed Signal Oscilloscope MSO71254C 12.5 GHz Mixed Signal Oscilloscope MSO71604C 16 GHz Mixed Signal Oscilloscope MSO72004C 20 GHz Mixed Signal Oscilloscope DPO70404B 4 GHz Digital Phosphor Oscilloscope DPO70604B 6 GHz Digital Phosphor Oscilloscope DPO70804B 8 GHz Digital Phosphor Oscilloscope DPO71254C 12.5 GHz Digital Phosphor Oscilloscope DPO71604C 16 GHz Digital Phosphor Oscilloscope DPO72004C 20 GHz Digital Phosphor Oscilloscope DSA70404B 4 GHz Digital Serial Analyzer DSA70604B 6 GHz Digital Serial Analyzer DSA70804B 8 GHz Digital Serial Analyzer DSA71254C 12.5 GHz Digital Serial Analyzer DSA71604C 16 GHz Digital Serial Analyzer DSA72004C 20 GHz Digital Serial Analyzer

All Models Include : Accessory pouch, front cover, mouse, keyboard, quick start user manual (071-173x-xx), (4) TekConnect and (1) TekConnect-to-BNC adapter (TCA-BNC), DPO/DSA/MSO70000 Series product software CD/DVD-ROM, performance veriﬁcation procedure PDF ﬁle, GPIB programmer's reference (on product software CD/DVD-ROM), calibration certiﬁcate documenting NIST traceability, Z 540-1 compliance and ISO9001, power cord, one-year warranty.

Note: Please specify quick-start user manual language and power plug when ordering.

to 2.92 mm adapters (TCA-292MM)

24 www.tektronix.com

Digital and Mixed Signal Oscilloscopes — DPO/DSA/MSO70000 Series

Options

Instrument Options

Option D PO700 00 DSA70000 MSO70000

Record Length Options

Opt. 2XL Opt. 5XL Opt. 10XL Opt. 20XL*

MSO70000 Digital Signal Analyzer Options

Standard XXX XXX XXX

Opt. DSAH X, for MSO70404,

Opt. DSAU X, for MSO71254C,

Trigger and Search Options

Opt. LT Opt. MTH

Opt. ST6G

Advanced Analysis Options

Opt. D-PHY* Opt. DDRA*

Opt. DJA Opt. DSPT*

11, 1 2

Opt. DVI Opt. ERRDT*

Opt. ET3* Opt. FBD*

Opt. HT3 Opt. HT3DS Opt. IBA* Opt. M-PHY* Opt. PCE* Opt. PWR*

Opt. RTE Opt. SLA Opt. SLE Opt. SST*

Opt. SVE Opt. SVM* Opt. SVP* Opt. SVT* Opt. USB* Opt. USB3*

9, 11

Opt. UWB

XXX X

Standard

XXX X X X DDR X

Standard XXX XXX XXX

XXX X X X FB-DIMM Memory Bus Analysis XXX XXX XXX XXX XXX XXX XXX XXX XXX XXX XXX XXX XXX XXX XXX XXX XXX

MSO70604, or

MSO70804

MSO71604C, or

MSO72004C

Description

31.25 MS/Ch

62.5 MS/Ch 125 MS/Ch 250 MS/Ch

MSO Digital Serial Analysis Bundle, includes Opt.

2XL, DJA, MTH, and ST6G

MSO Digital Serial Analysis Bundle, includes Opt.

2XL, DJA, MTH, and ST6G

Waveform Limit Testing

Mask testing for Serial Standards. Includes hardware

clock recovery for up to 3.125 Gb/s

Protocol Triggering and Decoding for 8b/10b-encoded

Serial Signals up to 6.25 Gb/s. Includes hardware clock

recovery and pattern lock triggering

D-PHY Essentials – Characterization and Analysis Solution

MIPI

Memory Bus Analysis

DPOJET Jitter and Eye Diagram Analysis

DisplayPort Compliance Test Solution

DVI Compliance Test Solution

Frame and Bit Error Rate Detector for High-speed Serial

Standards (Available through the programmable interface only)

Ethernet Compliance Test Software

HDMI Compliance Test Software

HDMI Direct Synthesis for HDMI 1.4

InﬁniBand Compliance Module for RT-Eye Analysis Software

M-PHY Essentials – Characterization and Analysis Solution

MIPI

PCI Express

Analysis Software

Power Measurement and Analysis Software RT-Eye Serial Data Compliance and Analysis Software Serial Data Link Analysis Advanced (with Equalization)

Serial Data Link Analysis Essentials (no Equalization)

SATA and SAS Analysis Software

SignalVu® Essentials – Vector Signal Analysis Software

General Purpose Modulation Analysis

Advanced Signal Analysis (including pulse measurements)

Frequency and Phase Settling Time Measurements

USB 2.0 Compliance Test Software

USB 3.0 Compliance and Analysis Software

Ultra-Wideband Spectral Analysis (includes WiMedia

Alliance PHY interface testing)

www.tektronix.com 25

Data Sheet

Option D PO700 00 DSA70000 MSO70000

Floating Optio

n Licenses

Description

Floating Licenses offer an alternative method to manage your Tektronix asset. Floating licenses allow license-key enabled options to be easily moved among all your DPO/DSA/MSO70000 and DPO7000 Series oscilloscopes. Floating licenses are available for the following license-key enabled options.

Check www.tek.com/products/oscilloscopes/ﬂoatinglicenses for additional information about ﬂoating license options. DPOFL-ASM DPOFL-CP2 DPOFL-D-PHY*

XXX XXX XXX

ANSI/ITU Telecom Pulse Compliance Test S oftware

MIPI

Advanced Event Search and Mark

D-PHY Transmitter Debug, Characterization,

and Compliance Test Solution DPOFL-DDRA* DPOFL-DJA DPOFL-DSA DPOFL-DSPT* DPOFL-DVI DPOFL-ERRDT*

11, 1 2

X X X DDR Memory Bus Analysis X

Standard XX XXX XXX XXX

Jitter and Eye Analysis Tools – Advanced (DPOJET)

Digital Serial Analysis Bundle

DisplayPort Transmitter Compliance Test Software

DVI Compliance Testing

Frame and Bit Error Rate Detector for High-speed

Serial Standards

DPOFL-ET3* DPOFL-FBD* DPOFL-HT3 DPOFL-HT3DS DPOFL-IBA*

DPOFL-J2 DPOFL-JA3 DPOFL-JE3 DPOFL-LT DPOFL-MTH DPOFL-PCE* DPOFL-PTD DPOFL-PWR* DPOFL-RTE DPOFL-SLA DPOFL-SLE DPOFL-SST* DPOFL-ST6G DPOFL-STU

XXX

Ethernet Compliance Testing X X X FB-DIMM Memory Bus Analysis XXX XXX XXX XXX

HDMI Compliance Testing

HDMI Direct Synthesis for HDMI 1.4

Inﬁniband Compliance Module

Disk Drive Measurements Software X X X Jitter and Timing Measurements – JIT3 Advanced XXX XXX X

Standard

Mask Testing, includes Hardware Clock Recovery XXX X

Standard

Protocol Trigger and Decode for 8b/10b

TDSJIT3 Essentials

Waveform Limit Testing

PCI Express

Measurements

X X X Power Measurement and Analysis XXX XXX XXX XXX X

Standard

Real-timeEye–SerialDataComplianceandAnalysis

Serial Data Link Analysis – Advanced (includes Equalization)

Serial Data Link Analysis – Essentials (no Equalization)

SAS and Serial ATA Compliance Module

8b/10b Serial Protocol Trigger and Decode up to 6.25 Gb/s

Upgrade from 3.125 Gb/s to 6.25 Gb/s 8b/10b Serial

Protocol Trigger and Decode DPOFL-SVT* DPOFL-USB* DPOFL-USB3* DPOFL-UWB DPOFL-XL02 DPOFL-XL05 DPOFL-XL010 DPOFL-XL020*

9, 11

XXX XXX XXX

Settling Time Measurements – Frequency and Phase

USB 2.0 Compliance Testing

USB 3.0 Essentials X X X Ultra Wideband Analysis X

Standard XXX XXX XXX

Extended record length – 31.25M Samples/Ch

Extended record length – 62.5M Samples/Ch

Extended record length – 125M Samples/Ch Extended record length – 250M Samples/Ch

26 www.tektronix.com

Digital and Mixed Signal Oscilloscopes — DPO/DSA/MSO70000 Series

Option D PO700 00 DSA70000 MSO70000

TekExpress®Ap

plication Framework

Description

TEKEXP X X X TekExpress Au Opt. HEAC Opt. SATA-TSG Opt. SATA-RSG Opt. SATA-RXTX Opt. SATA-DHB

XXX XXX XXX

SATA PHY/TSG/OOB Transmitter Tests for TekExpress

SATA RSG/RMT Receiver Tests for TekExpress XXX XXX

SATA TekExpress SW Bundle (TSG, RSG, RXTX

HEAC Automated Solution

SATA Rx/Tx Channel Tests for TekExpress

for Hosts or Devices) Opt. SATA-SI Opt. USB-RMT Opt. USB-TX*

9, 11

Opt. XGbT

*4Requires Ethernet Test Fixture.

s TDSUSBF (USB Test Fixture).

Require

At least Opt. 2XL and a TCA-1MEG TekConnect 1 MΩ buffer ampliﬁer are recommended for use.

Requires Opt. RTE.

ls of bandwidth ≥12.5 GHz only.

For mode

Requires DJA.

Requires Opt. SVE, SVEH, or SVEU.

dels of bandwidth ≥8GHzonly.

For mo

Requires Opt. DJA and 5XL.

Requires Opt. ST6G.

User Manu

Option

Opt. L0 Opt. L1

al Options

Description

English manual

French manual Opt. L3 German manual Opt. L5

Japanese manual Opt. L7 Simple Chinese manual Opt. L8 Standard Chinese manual Opt. L9 Opt. L10 Opt. L99

Korean manual

Russian manual

No manual

XXX XXX

TekExpress Automated USB 3.0 Receiver Solution XXX XXX

Service O

ptions

Option Description

Opt. CA1 Single calibration or functional veriﬁcation

Opt. C3 CalibrationService3Years

Opt. C5 CalibrationService5Years

Opt. D1 Calibration Data Report

Opt. D3 Calibration Data Report 3 Years (with Opt. C3)

Opt. D5 Calibration Data Report 5 Years (with Opt. C5)

Opt. G3 Complete Care 3 Years (includes loaner, scheduled

calibration and more)

SATA SI Cable Tests for TekExpress

TekExpress Automated USB 3.0 Solution

10GBASE-T Automated Solution

Opt. G5 Complete Care 5 Years (includes loaner, scheduled

Power Plug Options

Option

Description

Opt. A0 US plug, 115 V, 60 Hz Opt. A1 Opt. A2 Opt. A3

Euro plug, 220 V, 50 Hz UK plug, 240 V, 50 Hz Australian plug, 240 V, 50 Hz

Opt. R3 Repair Service 3 Years

Opt. R5 Repair Service 5 Years

Opt. IN Product Installation Service

Opt. IF Upgrade Installation Service

calibration and more)

Opt. A5 Swiss plug, 220 V, 50 Hz Opt. A6 Japanese plug, 100 V, 110/120 V, 60 Hz Opt. A10 China plug, 50 Hz Opt. A11 Opt. A12 Opt. A99

India plug, 50 Hz Brazilian plug, 60 Hz No power cord

tomation Framework

www.tektronix.com 27

Data Sheet

Recommended Accessories

Probes

Probe Descrip tion

P7520 P7516 P7513A P7313SMA 13 GHz TekConnect®differential SMA probe P7508 P7380SMA 8 GHz TekConnect differential SMA probe P7506 P7504 P6780 P6717 P6251

P6250

TCPA300/TCPA400 Series

P5200/P5205/P5210 High-voltage differential probes 067-0484-xx 067-1586-xx 067-1686-xx Power Deskew Fixture

Adapters

Adapter Description

TCA-1MEG TekConnect high-impedance buffer ampliﬁer. Includes

TCA-292MM TekConnect to 2.92 mm connectors TCA-BNC TekConnect-to-BNC adapter TCA-N TekConnect-to-N adapter TCA-SMA TekConnect-to-SMA adapter TCA75 8 GHz precision TekConnect 75 Ω to 50 Ω adapter with

20 GHz TriMode™ probe 16 GHz TriMode probe 13 GHz TriMode™ probe

8GHzTriModeprobe

6GHzTriModeprobe 4GHzTriModeprobe Differential Input Logic probe General-purpose Logic probe DC to 1 GHz, 42 V, differential probe (requires TCA-BNC

adapter) DC to 500 MHz, 42 V, differential probe (requires

TCA-BNC adapter) Current measurement systems

Analog Probe Calibration and Deskew Fixture (4 GHz) Analog Probe Deskew Fixture (>4 GHz)

P6139A passive probe

75 Ω BNC input connector

Cables

Cable Order Number

Centronics Cable GPIB Cable (1 m) GPIB Cable (2 m)

P6780 Logic Pr

Accessory

D-MAX Probe Footprint to Square Pin Header Adapter

MICTOR to Square Pin Header Adapter

Deskew Fixture Logic Probes

Standard Adapter Wide Body Adapter 020-3036-xx 25°/55° Holder HeatStripWire(4.57m) Hand Browsing Adapter 202-3031-xx Flex Adapter 020-3033-xx Lead Set Ground Probe Grouper

(including header pins) Ferrite Beads 020-3034-xx Wire Tubing (4.57 m)

012-1214-xx 012-0991-xx 012-0991-xx

obe Standard Accessories

Order Number

NEX-P6960PIN

NEX-HD2HEADER

067-2083-xx

020-3035-xx

020-3032-00 020-3021-00

020-3038-xx 020-3042-xx

020-3037-xx

P6717 Logic Probe Standard Accessories

Accessory

D-MAX Probe Footprint to Square Pin Header Adapter

MICTOR to Square Pin Header Adapter

Deskew Fixture Logic Probes

Extension Ground Tip Probe Tip 131-5638-xx IC Grabber Probe Grouper Lead Sets Ground Lead Sets

Order Number

NEX-P6960PIN

NEX-HD2HEADER

067-2083-xx

206-0559-xx

206-0569-xx 352-1115-xx 196-3501-xx 196-3497-xx

28 www.tektronix.com

Digital and Mixed Signal Oscilloscopes — DPO/DSA/MSO70000 Series

Accessories

Accessory

Memory Testing

DDR3 ×4/×8 Solder Chip Interposer NEX-DDR3MP78BSC DDR3 ×4/×8 Socket Chip Interposer NEX-DDR3MP78BSCSK DDR3 ×16 Solder Chip Interposer NEX-DDR3MP96BSC DDR3 ×16 Socket Chip Interposer NEX-DDR3MP96BSCSK DDR2 ×4/×8 Solder Chip Interposer NEX-DDR2MP60BSC DDR2 ×4/×8 Socket Chip Interposer NEX-DDR2MP60BSCSK DDR2 ×16 Solder Chip Interposer NEX-DDR2MP84BSC DDR2 ×16 Socket Chip Interposer NEX-DDR2MP84BSCSK Instrumented DIMM for DDR3 Order Scope NEXVu card for

System Test

TestFixtureforUsewithOpt. USB TDSUSBF 10GBASE-T Fixture for Use with Option

XGbT Software Ethernet Test Fixture

Crescent Heart Software; Serial ATA ZP test ﬁxture set for Host, Device, and Cable testing

Crescent Heart Software; ESerial ATA ZP test ﬁxture set for Host, Device, and Cable testing

HEAC TPA-KIT consists of: Main Board; Plug A-type board; Plug C-type board; 2 × TDR board with A Receptacle; 2 × TDR board with C Receptacle

HDMI Type C Fixture Set for Rx/Tx TF-HDMI-TPA-S/STX KEITHLEY INSTRUMENTS INC;

RF/Microwave switch system, 32 channel, unterminated, Americas power cord

Order Number

UDIMM Raw Card E. (Contact http://www.nexustechnology.com)

TF-XGbT

Order through Crescent Heart Software (http://www.c-h-s.com)

TF-SATA-SET-IV-ZP

TF-ESATA-SET-IV-ZP

TF-HEAC-TPA-KIT

S46-6666-A-AMER

Accessory

KEITHLEY INSTRUMENTS INC; RF/Microwave switch system, 32 channel, unterminated, Asia-Paciﬁc power cord

KEITHLEY INSTRUMENTS INC; RF/Microwave switch system, 32 channel, unterminated, Europe/Africa power cords

USB 3.0 A/B Fixture/Cable Kit TF-USB3-AB-KIT USB 3.0 A Plug Fixture TF-USB3-A-P USB 3.0 A Receptacle Fixture Kit TF-USB3-A-R USB 3.0 B Receptacle Fixture Kit TF-USB3-B-R 1000/100/10BASE-T Advanced Test

Package (consists of test ﬁxture PCB set, RJ45 interconnect cable, and 1000BASE-T jitter test channel cable)

1000/100/10BASE-T Basic Test Package (consists of test ﬁxture PCB set and RJ45 interconnect cable)

103 meter 1000BASE-T jitter test channel cable

Short (4 inch (0.1 meter)) RJ45 interconnect cable

Test ﬁxtures that complement the use of the TekEXP-XGbT solution

Other

Oscilloscope Cart Rackmount Kit 016-1985-xx Service Manual Spare HDD for DPO/DSA/MSO70000

Series Transit Case

Order Number

S46-6666-A-ASIAP

S46-6666-A-EURAF

TF-GBE-ATP

TF-GBE-BTP

TF-GBE-JTC

TF-GBE-SIC

TF-XGbT

K4000

071-1740-xx 065-0834-xx

6-1977-xx

www.tektronix.com 29

Data Sheet

Upgrade Options

The DPO/DSA/MSO70000 Series instruments can be easily upgraded after initial time of purchase.

To upgrade an existing DPO/DSA/MSO70000, order DPO-UP and option listed below. For example, DPO-UP DDRA.

Option

Description

Memory

Upgrade record length on a DPO70000 or MSO70000 Series from: XL02 XL05 XL010 XL020*

Standard Conﬁguration to Option 2XL Conﬁguration Standard Conﬁguration to Option 5XL Conﬁguration Standard Conﬁguration to Option 10XL Conﬁguration

Standard Conﬁguration to Option 20XL Conﬁguration Upgrade record length on a DPO70000, DSA70000, or MSO70000 Series from: XL25 XL210 XL220* XL510 XL520* XL1020*

Option 2XL Conﬁguration to Option 5XL Conﬁguration

Option 2XL Conﬁguration to Option 10XL Conﬁguration

Option 2XL Conﬁguration to Option 20XL Conﬁguration

Opt. 5XL Conﬁguration to Opt. 10XL Conﬁguration

Opt. 5XL Conﬁguration to Opt. 20XL Conﬁguration

Opt. 10XL Conﬁguration to Opt. 20XL Conﬁguration

Trigger and Search

Upgrade DPO70000, DSA70000, or MSO70000 Series with: ASM Advanced Event Search and Mark LT MTH

Waveform Limit Testing

Mask testing for Serial Standards with Hardware Clock

Recovery ST6G Protocol Triggering and Decoding for 8b/10b-encoded

Serial Signals (Up to 6.25 Gb/s) STU Increase Protocol Triggering and Decoding from

3.125 Gb/s to 6.25 Gb/s

Advanced Analysis

Upgrade DPO70000, DSA70000, or MSO70000 Series with:

CP2* D-PHY* DDRA* DJAH

ANSI/ITU Telecom Pulse Compliance Testing Software

MIPI®D-PHY Characterization and Analysis Solution

Upgrade to Option DDRA

DPOJET Jitter and Eye Diagram Analysis

(Upgrade for DPO70404 - DPO70804 or MSO70404 -

MSO70804 models) DJAU

DPOJET Jitter and Eye Diagram Analysis

(Upgrade for DPO71254 - DPO72004 or MSO71254 -

MSO72004 models) DSAH Digital Serial Analysis Bundle

(Upgrade for DPO/MSO70404 - DPO/MSO70804

models) DSAU MSO Digital Serial Analysis Bundle

(Upgrade for DPO/MSO71254 - DPO/MSO72004

models)

DSPT* DVI

EQ* ERRDTH*

DisplayPort Compliance Test Solution

DVI Compliance Test Solution

Equalization to upgrade from Option SLE to Option SLA

Frame and Bit Error Rate Detector (Upgrade for

DPO70404 - DPO70804, DSA70404 - DSA70804, or

MSO70404 - MSO70804 models)

Option

ERRDTU*

Description

Frame and Bit Error Rate Detector (Upgrade for DPO71254 - DPO72004, DSA71254 - DSA72004, or

MSO71254 - MSO72004 models) ET3 FBD* HT3

Ethernet Compliance Test Software

FB-DIMM Memory Bus Analysis

HDMI Compliance Test Software HT3DS HDMI Direct Synthesis for HDMI 1.4

IBA*

InﬁniBand Compliance Module for RT-Eye Analysis

Software J2

JA3

TDSDDM2 Disk-drive Analysis Software

TDSJIT3 Advanced Jitter and Timing Measurements

Software

M-PHY*

PCE* PTD PWR RJUP

MIPI®M-PHY Characterization and AnalysisSolution

PCI Express®Analysis Software

Protocol Decoding for 8b/10b-encoded Serial Signals

Power Measurement and Analysis Software

Upgrade DSA70000 Series with RT-Eye Serial Data

Compliance and Analysis Software RTE

RT-Eye Serial Data Compliance and Analysis Software SLA Serial Data Link Analysis Advanced (with Equalization) SLE Serial Data Link Analysis Essentials (No Equalization)

SST*

SATA and S AS Analysis Software Module for RT-Eye

Analysis Software

SVEH* SVEU*

SignalVu® Essentials – Vector Signal Analysis Software

SignalVu Essentials – Vector Signal Analysis Software SVM General Purpose Modulation Analysis.

Requires Option SVE SVP Adv

anced Pulsed Signal Analysis including

surements. Requires Option SVE

Mea SVT Frequency and Phase Settling Time Measurements.

Requires Opt. SVE USB USB 2.0 Compliance Test Software

9, 11

USB3* UWB

USB 3.0 Compliance and Analysis Software

Ultra-Wideband Spectral Analysis

(includes WiMedia Alliance PHY interf. testing)

VNM*

TDSVNM CAN and LIN Timing and Protocol Decode

(Triggering not included)

Other

*7Requires Opt. RTE.

For models of bandwidth ≥12.5 GHz only.

Requires DJA.

For models of bandwidth ≥8GHzonly.

Requires Opt. ST6G.

Requires Opt. MTH.

Requires Opt. ASM and DJA.

Requires Opt. SLE.

Requires. Opt. RTE or DJA.

For models of bandwidth ≤8GHzonly.

CAN/LIN trigger module available – Order ATM1 through Crescent Heart Software.

Upgrade Installation Service

30 www.tektronix.com

Digital and Mixed Signal Oscilloscopes — DPO/DSA/MSO70000 Series

Instrument Bandwidth Upgrades

The analog bandwidth of the DPO/DSA/MSO70000 Series instruments can be easily upgraded after initial time of purchase. To upgrade your instrument's bandwidth, order one of the products listed below.

Current Bandwidth Bandwidth After

Upgrade

DPO70000 and DSA70000 Series

4GHz 6GHz 4GHz 8GHz 4GHz 12.5GHz 4GHz 16GHz 4GHz 20GHz 6GHz 8GHz 6GHz 12.5GHz 6GHz 16GHz 6GHz 20GHz 8GHz 12.5GHz 8GHz 16GHz 8GHz 20GHz

12.5 GHz 16 GHz

12.5 GHz 20 GHz 16 GHz 20 GHz

DPO70000C and DSA70000C Series

12.5 GHz 16 GHz CBWU12T16

12.5 GHz 20 GHz CBWU12T20 16 GHz 20 GHz CBWU16T20

MSO70000 and MSO70000C Series

4GHz 6GHz 4GHz 8GHz 4GHz 12.5GHz 4GHz 16GHz 4GHz 20GHz 6GHz 8GHz 6GHz 12.5GHz 6GHz 16GHz 6GHz 20GHz 8GHz 12.5GHz 8GHz 16GHz 8GHz 20GHz

12.5 GHz 16 GHz

12.5 GHz 20 GHz 16 GHz 20 GHz

Model Num ber

BWU4T6

BWU4T8 BWU4T12 BWU4T16 BWU4T20

BWU6T8 BWU6T12 BWU6T16 BWU6T20 BWU8T12 BWU8T16 BWU8T20

BWU12T16 BWU12T20 BWU16T20

MBWU4T6

MBWU4T8 MBWU4T12 MBWU4T16 MBWU4T20

MBWU6T8 MBWU6T12 MBWU6T16 MBWU6T20 MBWU8T12 MBWU8T16 MBWU8T20

MBWU12T16 MBWU12T20 MBWU16T20

Product(s) are manufactured in ISO registered facilities.

Product(s) complies with IEEE Standard 488.1-1987, RS-232-C, and with Tektronix Standard Codes and Formats.

www.tektronix.com 31

Data Sheet

Contact Tektronix:

ASEAN / Australa

Balkans, Israel, South Africa and other ISE Countries +41 52 675 3777

Central East Eu

Mexico, Central/South America & Caribbean (52) 56 04 50 90

* European toll-free number. If not accessible, call: +41 52 675 3777

rope, Ukraine, and the Baltics +41 52 675 3777

Central Europe & Greece +41 52 675 3777

Middle E ast,

Asia, and North Africa +41 52 675 3777

The Netherlands 00800 2255 4835*

People’s Rep

Republic of

Russia & CIS +7 (495) 7484900

United Kingdom & Ireland 00800 2255 4835*

sia (65) 6356 3900

Austria 00800 2255 4835*

Belgium 00800 22

Brazil +55(11)37597600

Canada 1 800 833 9 200

Denmark +4580881401

Finland +41526

France 00800 2255 4835*

Germany 00800 2255 4835*

Hong Kong 400 8

India 000 800 650 1835

Italy 00800 2255 4835*

Japan 81 (3) 67

Luxembourg +41526753777

ublic of China 400 820 5835

Poland +41 52 675 3777

Korea 001 800 8255 2835

South Africa +41526753777

Spain 00800

Sweden 008 00 2255 4835*

Switzerland 00800 2255 4835*

Tai wa n 886 (

55 4835*

75 3777

20 5835

14 3010

Norway 800 16098

Portugal 80 08 12370

2255 4835*

2) 2722 9622

USA 1 800 833 9200

Updated 25 May 2010

www.tektronix.com

For Further Information. Tektronix maintains a comprehensive, constantly expanding collection of application notes, technical briefs and other resources to help engineers working on the cutting edge of technology. Please visit www.tektronix.com

Copyrigh

d pending. Information in this publication supersedes that in all previously published material.

issued an

tion and price change privileges reserved. TEKTRONIX and TEK are registered trademarks of

Speciﬁca

x, Inc. All other trade names referenced are the service marks, trademarks, or registered trademarks

Tek t ro ni

espective companies.

of their r

02 Dec 2010 55W-23446-6

Tektronix DPO 70000, MSO70000 DATASHEET

Specifications and Main Features

Frequently Asked Questions

User Manual