Tektronix MSO2000/B,DPO2000/B Series User manual

xx
DPO2000/B and MSO2000/B Series Oscilloscopes
ZZZ
Declassication and S ecurity
Instructions
www.tektronix.com
P077010801*
*
Copyright © Tektronix. All rights reserved. Licensed software products are owned by Tektronix or its subsidiaries or suppliers, and are protected by national copyright laws and international treaty provisions.
Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication supersedes that in all previously published material. Specica tions and price change privileges reserved.
TEKTRONIX and TEK are registered trademarks of Tektronix, Inc.
TekSecure is a trademark of Tektronix, Inc.
Contacting Tektronix
Tektronix, Inc. 14150 SW Karl Braun Drive P.O . B o x 5 00 Beaverton, OR 97077 USA
For product information, sales, service, and technical support:
In North America, call 1-800-833-9200. Worldwide, visit www.tektronix.com to nd contacts in your area.
Table of Contents
Preface .............................................................................................................. iii
Clear and Sanitize Procedures . ... ... ... . ... ... . ... ... . ... ... ... . ... ... . ... ... . ... ... ... . ... ... . ... ... . ... ... ... . .. 1
Memory Devices............................................................................................... 1
Data Export
Built-In Security Features .............................. ................................ ........................... 4
When to Use TekSecure............................ .................................. ......................... 4
What TekSecure Does......................................................................................... 4
Disable the LAN Port and Clear LAN Ethernet Settings.. ... . ... ... . ... ... . ... ... . ... ... . ... ... . .. . ... . . . 5
Disable the USB Device Port................................................................................. 6
Clear an
d Sanitize a Non-Functional Instrument.. . .. . ... ... . ... ... ... . ... ... . ... ... ... . ... ... . .. . ... ... . ... ... . 7
Devices........................................................................................... 3
DPO2000/B and MSO2000/B Series Declassication and Security Instructions i
Table of Contents
ii DPO2000/B and MSO2000/B Series Declassication and Security Instructions
Preface
If you have data security concerns, this document helps you to sanitize or remove memory devices from the DPO2000/B and MSO2000/B Series Digital Phosphor and Mixed Sig
The DPO2000/B and MSO2000/B series products h ave data storage (memory) devices and to clear or sanitize the memory devices, and also tell you how to declassify an instrument that is not functioning.
Instrument code and calibration settings reside in nonvolatile ash memory. Instrument setups and reference waveforms may also be stored in ashmemoryor on USB drives connected to the instrument.
If you have any questions, contact the Tektronix Technical Support Center at www.tektronix.com/support.
nal Oscilloscopes.
data output devices (USB ports). These instructions tell you how
Products
Related Documents
The following Tektronix products are covered by this document:
DPO20
DPO2004B
DPO2012/B
DPO2014/B
DPO2022B
DPO2024/B
MS
MSO2004B
MSO2012/B
MSO2014/B
MSO2022B
MSO2024/B
The DPO2000 and MSO2000 Series Digital Phosphor and Mixed Signal Oscilloscopes Service Manual, part number 071-2331-XX, is available on the Tektronix Web site at www.tektronix.com/manuals.
02B
O2002B
DPO2000/B and MSO2000/B Series Declassication and Security Instructions iii
Preface
Terms
The following t
Clear. This removes data on media/memory before reusing it in a secured area. All reus information by standard means of ac cess.
Erase. This
Media storage/data export device. Any of several devices that can be used
to store or e
Nonvolatile memory. Data is retained when the instrument is powered off.
Power off. Some instruments have a “Standby” mode, in which power is
still supplied to the instrument. For the purpose of clearing data, putting the instrume products, you will need to either press a rear-panel OFF switch or remove the power source from the instrument.
Remove. This is a physical means to clear the data by removing the memory device from the instrument. Instructions are available in the product Service Manual.
Sanitize. This eradicates the data from media/memory so that the data cannot be recovered by other means or technology. This is typically used when the device will be moved (temporarily or permanently) from a secured area to a non-secured area.
ermsmaybeusedinthisdocument:
able memory is cleared to deny access to previously stored
is equivalent to clear.
xport data from the instrument, such as a USB port.
nt in Standby mode does not qualify as powering off. For these
Scrub. This is equivalent to sanitize.
User-modiable. The user can write to the memory d evice during normal
instrument operation, using the instrument interface or remote control.
Volatile memory. Data is lost when the instrument is powered off.
iv DPO2000/B and MSO2000/B Series Declassication and Security Instructions
Clear and Sanitize Procedures
Memory Device
s
The following tables list the volatile and nonvolatile memory devices in the standard instrument and listed options.
Table 1: Vol
Type and minimum size Function User modiable
CMOS, SDRAM, 32MX16, 512MB DDR2, 1.8V, 333MHZ; MT47H32M16CC-3, FBGA84
CMOS, SDRAM, 32MX16, 512MB DDR2, 1.8V, 333MHZ; MT47H32M16CC-3, FBGA84
CMOS, SDRAM, 64MX16, 1G DDR2, 1.8V, 333MHZ; MT47H64M16BT-3, FBGA84
CMOS, SDRAM, 32MX16, 512MB DDR2, 1.8V, 333MHZ; MT47H32M16CC-3, FBGA84
atile Memory Devices for the DPO2000/B and MSO2000/B Series
DDR memory: contains the analog channel waveform acquisition data during operation
DDR memory: contains the digital channel waveform acquisition data during operation
DDR memory: contains the instrument code and data during operation
DDR memory: contains the instrument code and data during operation
Only by the processor system
Only by the processor system
Only by the processor system
Only by the processor system
Data input method Location To clear or sanitize
N/A
N/A
N/A
N/A
Acquisition board
Acquisition board (MSO2000/B Series only)
Acquisition board
Acquisition board (4-channel products only)
Remove power from the instrument for at least 20 seconds
Remove power from the instrument for at least 20 seconds
Remove power from the instrument for at least 20 seconds
Remove power from the instrument for at least 20 seconds
DPO2000/B and MSO2000/B Series Declassication and Security Instructions 1
Clear and Sanitize Procedures
Table 2: Nonvol
atile Memory Devices for the DPO2000/B and MSO2000/B Series
Type and minimum size Function User modiable
CMOS, FLASH; 16M X 8 OR 8M X 16, 128MBIT, 75NS, 3V; PC28F128J3D-75, BGA64
CMOS, CLOCK; SERIAL REAL-TIME CLOCK, CRYSTAL, 7 X 8 RAM, SPI,
3.3V; M41T93RMY, SO18.300
CMOS, EEPROM; 128 X 8, SERIAL; 24C01A, SOIC8
CMOS, MICROCONTROLLER; 8-BIT, 32K BYTES ON-CHIP FLASH, MC9S08AW32CPUE, LQFP64
CMOS, EEPROM; 256 X 8, SERIAL; 24C02, SO8.15
FLASH: contains the instrument rmware, calibration constants, reference waveforms, and instrument setups
Real-time clock, with battery backup
EEPROM: contains the front end board serial number and calibration information
Microcontroller with FLASH: contains the front panel processor code and power status for soft power switch
EEPROM: contains the application module rmware
N/A N/A
Only by the processor system
N/A N/A
Only by the processor system
N/A N/A DPO2000/B and
Data input method Location To clear or sanitize
N/A
N/A
Acquisition board To clear: Not applicable
Acquisition board Not applicable; no user
Front End Board Not applicable; no user
Front Panel Board Not applicable; no user
MSO2000/B application module
for calibration constants.
Use the TekSecure featuretoerase reference waveforms and instrument setups.
Use the procedure to disable the LAN Ethernet and to clear information, such as IP addresses. (See page 5, Disable the
LAN Port and Clear LAN Ethernet Settings.)
To sanitize: Remove the acquisition board; see the product service manual for removal instructions. Store the removed board in a secure area or destroy it. Return the product to Tektronix and a new acquisition board will be installed and the instrument will be repaired and adjusted as necessary.
data
data
data
Not applicable; no user data
2 DPO2000/B and MSO2000/B Series Declassication and Security Instructions
Data Export Devices
The following table lists the data export devices.
Table 3: Data Export Devices
port
mum size
Function User modiab
USB ash dri storage of reference waveforms, screen images, and setups
Supports r and data transfer to a PC
ve; user
instrument
emote control
Type an d min i
USB host port Supports the removable
USB device
Data input
le
method Location To disable
Yes
Yes Remote
Save USB host port on the
control v USBTMC
ia
Clear and Sanitize Procedures
front of the
USB device rear of the instrument
instrument
port on the
Files can be deleted or overwritten on the instrument USB ash drive can be removed and destroyed.
The USB hos cannot be disabled.
Use the procedure to disable t port. (See page 6,
Disable the USB Device Port.)
or a PC; the
t port
he USB device
DPO2000/B and MSO2000/B Series Declassication and Security Instructions 3
Built-In Security Features
Built-In Secu
rity Features
When to Use TekSecure
What TekSecure Does
You can us e t stored in internal ash memory.
The DPO2000 front panel. Any U SB ash devices can be r emoved, and stored or destr oyed.
The TekSecure function does the following:
Replace
Replaces the current front-panel setup and all stored setups with the default setup v
Calculates the checksums of all reference waveform memory and setup memor erasure
he TekSecure function to erase setup and reference waveform data
/B and MSO2000/B series models have a USB host port on the
s all waveforms in all reference memories with null sample values
alues
y locations to verify successful completion of waveform and setup
To use TekSecure:
To reset the instrument
RAM:
ays a dialog indicating whether the secure erase was successful or
Displ unsuccessful
NOTE. TekSecure does not erase or change factory calibration constants, user
protected data, or Ethernet settings.
1. Push the front-panel Utility button.
2. Push the Utility Page lower-bezel button and use the Multipurpose a knob to select Config.
3. Push the TekSecure Erase Mem ory lower-bezel button.
ush the OK Erase Setup & Ref Memory side-bezel button. Wait for the
4.P
“TekSecure operation complete” dialog box to display.
5. Push the Menu Off front-panel button to close the dialog box.
1. Power off the instrument for at least 20 seconds.
2. Power on the instrument.
4 DPO2000/B and MSO2000/B Series Declassication and Security Instructions
Built-In Security Features
To overwrite protected
user data
This procedure
Send the following commands to the oscilloscope:
:PASSWORD “XYZZY” (or cur ren t password if not “XYZZY”)
:NEWPASS “ANYTHING”
:PASSWORD “ANYTHING”
*PUD #3300xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxx[repeat for a total of 300 x’s]
overwrites everything that is stored in the protected user data area.
Disable the LAN Port and Clear LAN Ethernet Settings
To disable the LAN port and clear LAN Ethernet settings, such as IP addresses, follow these steps:
CAUTION. If you need to restore network connectivity at a later date, make sure to
write down all setting values before clearing them.
1. Remove the network cable from the LAN port on the rear of the instrument.
2. Push the front-panel Utility button.
3. Push the Utility Page lower-bezel button and use the Multipurpose a knob to select I/O.
4. Push the Ethernet Network Settings lower-bezel button.
5. Push the Change Instrument Settings side-bezel button.
6. Pus
7. Pu
8. Push the arrow side-bezel button to position the cursor on the Instrument
9. Push the Clear lower-bezel button.
10. Push the arrow side-bezel button to position the cursor on the Domain
11. Push the Clear lower-bezel button.
12. Push the arrow side-bezel button to position the cursor on the DNS IP
htheor arrow side-bezel button to position the cursor on the User
Password information.
sh the Clear lower-bezel button.
P Address information.
I
Name information.
Address information.
13. Push the Clear lower-bezel button.
DPO2000/B and MSO2000/B Series Declassication and Security Instructions 5
Built-In Security Features
Disable t
14. Push the arrow Address information.
15. Push the Clear
16. Push the arrow side-bezel button to position the cursor on the Subnet Mask
informatio
17. Push the Clear lower-bezel button.
18. Push the OK Accept side-bezel button.
The LAN system is disabled and no longer allows data trafc in or out. The relevant LAN Ethernet settings are also cleared.
he USB Device Port
To disable the USB device port, follow these steps:
1. Remove any USB cable or device from the USB device port on the rear of the instrument.
2. Push the front-panel Utility button.
3. Push the Utility Page lower-bezel button and use the Multipurpose a knob
to select I/O.
side-bezel button to position the cursor on the Gateway IP
lower-bezel button.
n.
4. Push the USB lower-bezel button.
5. Push the Disabled (Off Bus) side-bezel button to disable the USB device port.
USB device port is disabled and no longer allows data trafcinorout.
The
6 DPO2000/B and MSO2000/B Series Declassication and Security Instructions
Clear and Sanitize a Non-Functional Instrum ent
Clear and Sani
Acquisition board
USB Flash Drive
tize a Non-Functional Instrument
If your instr as follows:
Only qualied personnel should perform service procedures. Read the Service
Safety Sum Series Digital Phosphor and Mixed Signal Oscilloscopes Service Manual before
performing any service procedures.
Remove the Acquisition board and return the product to Tektronix. A new Acquisition board will be installed, and the instrument will be repaired and adjusted as necessary.
For removal instructions, refer to the service manual, p art number 071-2331-XX, available on the Tektronix Web site at www.tektronix.com/manuals.
After removal of the Acquisition board, refer to your company's internal policies regarding han dling or disposal of the board.
Remove the USB ash drive and return the instrument to Tektronix for repair.
rremovaloftheUSBa sh drive, refer to you r company's internal policies
Afte regarding handling or disposal of the ash drive.
ument is not functioning and you need to clear or sanitize it, proceed
mary and the General Safety Summary in the DPO2000 and MSO2000
Charges
Replacement of any missing hardware will be charged according to the rate at
time of replacement.
the
DPO2000/B and MSO2000/B Series Declassication and Security Instructions 7
Loading...