Instructions
K420 Cart & LACART Brackets
for DPO7000 Series
407-5192-01
WARRANTY
Warranty
Tektronix warrants that this product will be free from defects in materials and workmanship for a period of one (1)
year from the date of shipment. If any such product proves defective during this warranty period, Tektronix, at its
option, either will repair the defective product without charge for parts and labor, or will provide a replacement in
exchange for the defective product. Parts, modules and replacement products used by Tektronix for warranty work
may be new or reconditioned to like new performance. All replaced parts, modules and products become the prop
erty of Tektronix.
In order to obtain service under this warranty, Customer must notify Tektronix of the defect before the expiration
of the warranty period and make suitable arrangements for the performance of service. Customer shall be responsible for packaging and shipping the defective product to the service center designated by Tektronix, with shipping
charges prepaid. Tektronix shall pay for the return of the product to Customer if the shipment is to a location within
the country in which the Tektronix service center is located. Customer shall be responsible for paying all shipping
charges, duties, taxes, and any other charges for products returned to any other locations.
This warranty shall not apply to any defect, failure or damage caused by improper use or improper or inadequate
maintenance and care. Tektronix shall not be obligated to furnish service under this warranty a) to repair damage
resulting from attempts by personnel other than Tektronix representatives to install, repair or service the product;
b) to repair damage resulting from improper use or connection to incompatible equipment; c) to repair any damage
or malfunction caused by the use of non-Tektronix supplies; or d) to service a product that has been modified or
integrated with other products when the effect of such modification or integration increases the time or difficulty of
servicing the product.
-
THIS WARRANTY IS GIVEN BY TEKTRONIX WITH RESPECT TO THE PRODUCT IN LIEU OF ANY OTH
ER WARRANTIES, EXPRESS OR IMPLIED. TEKTRONIX AND ITS VENDORS DISCLAIM ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. TEKTRONIX’
RESPONSIBILITY TO REPAIR OR REPLACE DEFECTIVE PRODUCTS IS THE SOLE AND EXCLUSIVE
REMEDY PROVIDED TO THE CUSTOMER FOR BREACH OF THIS WARRANTY. TEKTRONIX AND ITS
VENDORS WILL NOT BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL
DAMAGES IRRESPECTIVE OF WHETHER TEKTRONIX OR THE VENDOR HAS ADVANCE NOTICE OF
THE POSSIBILITY OF SUCH DAMAGES.
Copyright © Tektronix, Inc. 2006. All rights reserved.
Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication supersedes that in all previously
published material. Specifications and price change privileges reserved.
Printed in the U.S.A
Tektronix, Inc., P.O. Box 500, Beaverton, OR 97077-0001
TEKTRONIX and TEK registered trademarks of Tektronix, Inc.
-
Contacting Tektronix
Copyright © Tektronix, Inc. All rights reserved. Licensed software products are owned by Tektronix or its subsidiaries or suppliers, and are protected by national copyright laws and international treaty provisions.
Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication
supercedes that in all previously published material. Specifications and price change privileges reserved.
TEKTRONIX and TEK are registered trademarks of Tektronix, Inc.
Contacting Tektronix
Tektronix, Inc.
14200 SW Karl Braun Drive
P.O. Box 500
Beaverton, OR 97077
USA
For product information, sales, service, and technical support:
In North America, call 1-800-833-9200.
Worldwide, visit www.tektronix.com to find contacts in your area.
407-5192-01 Bracket Instructions
i
Introduction
This manual tells how to mount a DPO7000 series device to either a K420 cart or LACART using the provided
brackets.
Assembly will require approximately 15 minutes.
Tools
Mounting hardware is provided with the brackets.
You will need to provide a Phillips screwdriver and an 11/32” nut driver, wrench, or small crescent wrench for the
8-32 nuts listed below.
Parts Identification
The brackets are packed separately in the shipping carton. A bag of small parts is also packed in the box. Figure 1
on page 2 show the parts you will be using.
Table 1 below lists all the parts needed to assemble the brackets, including hardware. Take an inventory now to
familiarize yourself with the parts for the assembly process.
Table 1: Parts List
Quantity Description
Large Parts
1 Left Bracket
1 Right Bracket
Small Parts in Bag
2 10-32 x 3/8” Pan Head Screws With Lockwasher
6 8-32 x 3/8” Pan Head ScrewsWith Lockwasher
2 8-32 Hex Nut
Tools (Not Provided)
1 Phillips Screwdriver
1 11/32” Nut driver, Wrench or Crescent Wrench
407-5192-01 Bracket Instructions
1
Introduction
LEFT BRACKET
RIGHT BRACKET
10-32 X 3/8” Screw
Figure 1: Identification of Small Parts
407-5192-01 Bracket Instructions
8-32 X 3/8” Screw
8-32 Hex Nut
2
Introduction
Top Shelf
DPO7000 Series Device
Left Bracket
Right Bracket
Figure 2: Brackets & Device Shown On K420 Cart
407-5192-01 Bracket Instructions
3
Install Brackets On Device
Begin by mounting the brackets to the device. You will use these parts:
• 4 8-32 x 3/8” Pan Head Screw With Lockwasher
• 1 Right Bracket
• 1 Left Bracket
You will use a Phillips screwdriver to install these parts onto the device.
1. The brackets are mounted near the sides of the device using the holes in the bottom of the device as shown in
Figure 3. Device is shown from the rear. Be careful to put each bracket on the correct side. Also note that the front
feet must be in the open position to install the brackets.
REAR of Device
Right Bracket
8-32 x 3/8” Screw
Left Bracket
8-32 x 3/8” Screw
Figure 3: Installing The Brackets, Shown On DPO7000 Series Device
407-5192-01 Bracket Instructions
4
Install Brackets On Device
2. Once the brackets are in place tighten screws using the Philips screwdriver.
3. Fold closed the front feet on device
Front Foot
Figure 4: Brackets Installed, Shown On DPO7000 Series Device
407-5192-01 Bracket Instructions
Front Foot
5
Install On Cart (Option #1, Rearward)
To install the instrument to the cart you will need the following items:
• 2 8-32 x 3/8” Pan Head Screw With Lockwasher
• 2 Hex Nut
• 2 10-32 x 3/8” Pan Head Screw With Lockwasher
You will use a Philips screwdriver and an 11/32” nut driver or wrench to install these parts
1. Place device, with mounting brackets installed, onto cart in orientation shown in Figure 6 below.
2. Place the device so the rear holes in the brackets align with the 10-32 holes in the top shelf of the cart starting
with the left bracket. The correct rearward hole is marked with an ‘R’ on the left bracket. Install the 10-32
screw with the Phillips screwdriver but leave slightly loose. Repeat this step for right bracket.
3. Fasten an 8-32 screw through the forward hole in the left bracket, marked with an ‘R’, and through the slot in the
cart top, to the hex nut. Repeat this step for the forward hole in the right bracket.
4. Tighten all screws.
10-32 x 3/8” Screws
Hex Nuts
8-32 x 3/8” Screws
FRONT of Cart
REAR of Cart
Figure 5: Aligning Instrument With Cart, Shown On K420 Cart
407-5192-01 Bracket Instructions
6
Install On Cart (Option #2, Forward)
To install the instrument to the cart you will need the following items:
• 2 8-32 x 3/8” Pan Head Screw With Lockwasher
• 2 Hex Nut
• 2 10-32 x 3/8” Pan Head Screw With Lockwasher
You will use a Philips screwdriver and an 11/32” nut driver or wrench to install these parts
1. Place device, with mounting brackets installed, onto cart in orientation shown in Figure 6 below.
2. Place the device so the front holes in the brackets align with the 10-32 holes in the top shelf of the cart starting
with the left bracket. The correct forward hole is marked with an ‘F’ on the left bracket. Install the 10-32
screw with the Phillips screwdriver but leave slightly loose. Repeat this step for right bracket.
3. Fasten an 8-32 screw through the rearward hole in the left bracket, marked with an ‘F’, and through the slot in
the cart top, to the hex nut. Repeat this step for the rearward hole in the right bracket.
4. Tighten all screws.
8-32 x 3/8” Screws
10-32 x 3/8” Screws
FRONT of Cart
REAR of Cart
Hex Nuts
Figure 6: Aligning Instrument With Cart, Shown On K420 Cart
407-5192-01 Bracket Instructions
7
Loading...