Tektronix Heat Sink Hardware Installation Manual
020-2616-XX, 020-2719-XX
(Chipcool 1&2) for
TMSMPH1/2/3/4 probe heads.
020- 2719- XX Chipcool 1&2
020- 2616- XX Chipcool 1&2
020- 2617- XX Desktop
020- 2618- XX Cooler Master
Heat Sink Hardware
Installation Instructions
www.tektronix.com
*P075091800*
075-0918-00
Kit Contents
H Attaching hardware kits
H Instruction sheet
Tools Required
H Phillips (P1) screwdriver to tighten the
screws
H Flathead screw driver to lock the ZIF socket
H Optional: A torque wrench helps to ensure
reliable connections by meeting the nominal
torque values. When attaching screws use
2 in-lbs (0.226 N
G
m) of torque.
NOTE. Follow the illustration steps
from the bottom to the top
Insert the four posts into
5
thefourheat-sinkslots.
Using the supplied screws,
4
attach the two top brackets to
the bottom brackets.
Connect the microprocessor and
3
probe head to the target system.
Refer to the Support Instruction
Manual that came with the probe
head.
Using the supplied screws,
2
attach the two bottom brackets
to the bottom plate as shown.
Note. The Spacer kit (not shown) can
not be used with heat sink hardware.
Refer to the support instruction
manual that came with the probe
head.
.
Slot
Post
(black)
(blue)
(black)
(blue)
Overview
Use this instruction sheet to install the heat sink
hardware. Refer to the support instruction
manual that came with the probe adapter to
connect the probe head to the logic analyzer.
Only qualified personnel should perform these
procedures.
CAUTION. To prevent damage to the probe-head
pins, carefully align the pin layout with the
probe-head pins before installing the probe
head.
Procedure
Y ou must remove the heat sink and retention
brackets before installing the probe head.
To install the heat sink hardware, follow the steps
in the illustration that apply to the probe head
and heat sink hardware.
1
Insert the bottom plate.
Target system
Table 1: 020-2616-XX Replaceable parts list
Description
ACCESSORY KIT;
CHIPCOOL 1&2
HEATSINK, JEWEL CASE
&HEATSINK
PARTS;TMSMPH1/2/3/4
4 SCREWS 211-3008-XX
2 TOP BRACKETS 407-5035-XX (BLACK)
2BOTTOMBRACKETS 407-5037-XX (BLACK)
1 BOTTOM PLATE 386-7440-XX
Table 2: 020-2617-XX Replaceable parts list
Description
ACCESSORY KIT;
DESKTOP HEATSINK
ATTACH, JEWEL CASE &
HEAT SINK
PARTS;TMSMPH2/3
8 SCREWS,SOCKET CAP 212-0236-XX
4 STANDOFFS 129-1620-XX
Table 3: 020-2618-XX Replaceable parts list
Description
HEATSINK KIT; COOLER
MASTER HEATSINK
ATTACH, JEWEL CASE &
HEAT SINK PARTS;
TMSMPH3
2 STAND-OFF POSTS 355-0305-XX
4 SCREWS, PAN HEAD 211-0888-XX
2 UPPER BRACKET 407-5080-XX (GREEN)
2 LOWER BRACKET 407-5078-XX (GREEN)
1 COPPER SPACER 361-1825-XX
Tektronix part number
020-2719-XX,
020-2616-XX
407-5036-XX (BLUE)
407-5038-XX (BLUE)
Tektronix part number
020-2617-XX
Tektronix part number
020-2618-XX
407-5081-XX (RED)
407-5079-XX (RED)
Warranty Information
For warranty information, go to
www.tektronix.com, click Support, and then use
the provided links to search for the warranty for
your product.
Contacting Tektronix
Tektronix, Inc.
14200 SW Karl Braun Drive
PO Box 500
Beaverton, OR 97077
USA
For product information, sales, service, and
technical support:
H In North America, call 1--800--833--9200.
H Worldwide, visit www.tektronix.com to find
contacts in your area.
Place the heat sink
3
inside the brackets.
1
Connect the
microprocessor and
probe head to the target
system. Refer to the
Support Instruction
Manual that came with the
probe head.
Using the two supplied
5
screws, attach the top
brackets to the bottom
brackets.
Connect the
4
microprocessor and
probe head to the target
system. Refer to the
Support Instruction
Manual that came with the
probe head.
Attach the two green
3
standoffs to the bottom
plate.
1
Insert the bottom plate.
020-2 61 7-XX (Desktop) for
TMSMPH/2/3 probe heads.
2
020-2618-XX (Cooler Master) for
TMSMPH3 probe head.
(Green)
(Green)
Using the supplied
screws, attach the two
brackets to the target
system as shown.
Attach the
7
heat sink.
Apply thermal
grease to both
6
sides of the
copper spacer.
(Red)
(Red)
Using the two supplied
screws, attach the two
red bottom brackets to
the bottom plate.
2
Copyright © Tektronix, Inc.
Beaverton, OR 97077
Loading...