Tektronix Environment Programmer
xx
Environment Signals
ZZZ
Application Plug-in
Programmer Manual
*P077140200*
077-1402-00
xx
Environment Signals
ZZZ
Application Plug-in
Programmer Manual
www.tek.com
077-1402-00
Copyright © Tektronix. All rights reserved. Licensed software products are owned by Tektronix or its subsidiaries
or suppliers, and are protected by national copyright laws and international treaty provisions.
Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication
supersedes that in all previously published material. Specifications and price change privileges reserved.
TEKTRONIX and TEK are registered trademarks of Tektronix, Inc.
®
SourceXpress
is a registered trademark of Tektronix, Inc.
Contacting Tektronix
Tektronix, Inc.
14150 SW Karl Braun Drive
P.O. Box 5 0 0
Beaverto
USA
For product information, sales, service, and technical support:
n, OR 97077
In North America, call 1-800-833-9200.
Worldwide, visit www.tek.com to find contacts in your area.
Table of Contents
Getting Started
Introducti
Documentation............. .................................. ................................ ..................... 1-2
on ........................ ................................ ................................ ............... 1-1
Syntax and Commands
Command Syntax.................................... ................................ ............................. 2-1
Commands
Control commands.................... ................................ ................................ ....... 2-3
Compile commands .................................... ................................ ..................... 2-3
Scenario commands .... ................................ .................................. ................... 2-4
Emitter commands.... . ..... ..... . ..... . ..... . .... . ..... . ..... . ..... ..... . ..... . ..... . .... . ..... . ..... . ..... . 2-5
Analog modulation emitter commands ..... . ..... . ... . . ..... . ..... . ... . . . .... . ..... . ..... . ... . . ..... . ..... 2-6
Bluet
CDMA emitter commands.................................................................................. 2-7
Digital modulation emitter commands .. . ..... . ..... . ..... . ..... . ..... . .... . . .... . . .... . ..... . ..... . ..... . 2-7
DVB-T emitter commands. . ..... . .... . ..... . ..... . ..... . ... . . . .... . ..... . ..... . ..... . ..... ..... . ..... . ... 2-11
GSM emitter commands ..... . .... . ..... . ..... . ..... . .... . . .... . ..... . ..... . ..... . .... . ..... . ..... . ..... . . 2-11
LTE emitter commands . . .... . ..... . ..... . ..... . ... . . ..... . ..... . ..... . ... . . . .... . ..... . ..... . ..... . ..... . 2-11
Noi
OFDM emitter commands . . ..... . ..... . ..... . ..... . ..... . ..... . ..... . ..... . ..... . ..... . ..... . ..... . ..... . 2-12
P25 emitter commands .... . ..... . ..... . ..... . ..... . ..... . .... . . .... . . .... . ..... . ..... . ..... . ..... . ..... . .. 2-18
Pulse emitter commands ... . . ..... . ..... . ..... . ... . . . .... . ..... . ..... . ..... . ..... ..... . ..... . ..... . ..... . . 2-18
Radar emitter commands. ..... . ..... . ..... . .... . . .... . . .... . ..... . ..... . ..... . ..... . ..... . ..... ..... . ..... 2-18
Tones emitter commands. . ..... . ... . . ..... . ..... . ..... . ..... . ..... . ..... . ..... . ..... . ..... . ..... . ..... . ... 2-27
User defined emitter commands... . . .... . ..... . ..... . ..... . ..... . ..... . ..... . ..... . ..... . ..... . ..... . .... 2-27
WCDMA emitter commands.......... .................................. ................................ . 2-27
WiFi emitter commands.. . ..... . ..... . ..... ..... . ..... . ..... . .... . ..... . ..... . ..... ..... . ..... . ..... . .... . 2-28
WiMaX emitter commands .... . . .... . . .... . . .... . . ... . . . ... . . . ... . . . ... . . . ..... . ..... . ..... . ..... . ..... . . 2-28
Commands in alphabetical order......................... ................................ ..................... 2-29
by Groups ........................................................................................... 2-3
ooth emitter commands .... . ..... . ..... . ..... . ..... . ..... . ... . . ..... . ..... . ..... . ..... . ..... . ... . . . ... 2-7
se emitter commands... . ..... . ..... . ..... . ..... . ..... . ..... . ..... . ..... . ... . . ..... . ..... . ..... . ..... . . 2-12
Environment Signals Plug-in Programmer Manual i
Table of Contents
ii Environment Signals Plug-in Programmer Manual
Getting Started
Introduction
This programmer manual provides information on how to use commands for
remotely controlling the Environment Signals plug-in application.
The Environment Signals plug-in can be installed in the SourceXpress software
application, AWG70000 series instruments, and AWG5200 series instruments.
Communication with the plug-in is through the SourceXpress programmatic
interface or the AWG70000 series instrument’s programmatic interface. Using
a single VISA or raw socket session, it is possible to communicate with
SourceXpress, AWG70000 series instruments, and AWG5200 series instruments.
For information on the Remote Control, GPIB Parameters, LAN Parameters,
Connecting to the Instrument using GPIB, and Setting up GPIB Communication,
refer to t
Manual or the AWG5200 series Arbitrary Waveform Generators Programmer
Manual.
he AWG70000 series Arbitrary Waveform Generators Programmer
Environment Signals Plug-in Programmer Manual 1-1
Documentation
Documentation
In addition to this Environment Programmer Guide, the following documentation
is included with this application:
Environment Signals Help. The help provides in-depth operation and user
interface help.
Environment Signals User Manual (PDF). This is adapted from the
Environment Signals help system.
1-2 Environment Signals Plug-in Programmer Manual
Syntax and Commands
Command Syntax
For information on the Syntax Overview, Command and Query Structure,
Clearing the Instrument, Command Entry, Parameter Types, SCPI Commands
and Queries,
Programmer Manual or the AWG5200 series Arbitrary Waveform Generators
Programmer Manual.
refer to the AWG70000 Series Arbitrary Waveform Generators
Environment Signals Plug-in Programmer Manual 2-1
Command Syntax
2-2 Environment Signals Plug-in Programmer Manual
Commands by Groups
This section contains a list of all PI commands grouped together in relation
to their functions. Each command has a brief description and is linked to the
detailed des
Control commands
cription.
Table 2-1:
Item Descripti
ENVironme
WPLugin:
Control commands
nt:RESet
ACTive
Resets the
Sets or re
on
Environment Signal plug-in to its default state.
turns the active waveform plug-in.
Compile commands
Table 2-2: Compile commands
Item Description
ENVironment:COMPile Compiles and generates a waveform using the Environment
plug-in compile settings.
ENVironment:COMPile:AWARound Sets or returns the Adjust Wrap Around state (enabled or
led) for the Compile Settings.
disab
onment:COMPile:CANCel
ENVir
ronment:COMPile:CASSign
ENVi
ENVironment:COMPile:CHANnel:I Sets or returns the playout channel intended for the compiled I
ENVironment:COMPile:CHANnel:Q Sets or returns the playout channel intended for the compiled Q
NVironment:COMPile:CHANnel:RF
E
ENVironment:COMPile:CORRection:APPLy Sets or returns the Apply Corrections File state (enabled or
ENVironment:COMPile:CORRection:PATH Sets or returns the RF Correction file name and filepathtouse
ENVironment:COMPile:CORRection:PATH:I Sets or returns the I Correction file name and filepathtouse
ENVironment:COMPile:CORRection:PATH:IQ Sets or returns the IQ Correction file name and file path to use
ls a compilation currently in progress.
Cance
or returns the state (enabled or disabled) to compile the
Sets
waveform and immediately assign it to a specified channel
(enabled) or just compile the waveform (disabled).
nal waveform when the signal format is set to IQ. The selected
sig
channel is also used to define the amplitude ranges.
signal waveform when the signal format is set to IQ. The selected
annel is also used to define the amplitude ranges.
ch
ets or returns the playout channel intended for the compiled
S
RF signal waveform when the signal format is set to R F/IF. The
selected channel is also used to de fi ne the amplitude ranges.
disabled) for the Compile Settings.
when compiling an RF signal.
when compiling and IQ signal.
when compiling and IQ signal.
Environment Signals Plug-in Programmer Manual 2-3
Commands by Groups
Table 2-2: Compile commands (cont.)
Item Description
ENVironment:COMPile:CORRection:PATH:Q Sets or returns the Q correction file name and file path to use
when compiling and IQ signal.
ENVironment:COMPile:CORRection:TYPE Sets or returns the type of IQ correction file (a single IQ file or
individual I and Q files) to apply when compiling.
ENVironment:COMPile:DUPConverter Sets or returns the Internal IQ Modulator state (enabled or
disabled) when compiling.
ENVironment:COMPile:FDRange Sets or returns the Fit to full dynamic range state (enabled or
disabled) for the Compile Settings.
ENVironment:COMPile:MARKer:ENABle Sets or returns the Marker Data state (enabled or disabled) for
the Compile Settings.
ENVironment:COMPile:MARKer[n]:CFRequency Sets or returns the Marker Data clock frequency when the Marker
Data type is set to Clock Frequency.
ENVironment:COMPile:MARKer[n]:MDATa Sets or returns the Marker Data Type of the specified marker.
ENVironment:COMPile:NAMe Sets or returns the name o f the compiled waveform.
ENVironment:COMPile:OSAMpling Sets or returns the over sampling rate used to determine the
sampling rate of the compiled signal.
ENVironment:COMPile:OVERwrite Sets or returns the state (enabled or disabled) wether or not to
overwrite the existing waveform if the w aveform already exists in
the Waveform list.
ENVironment:COMPile:PLAY Sets or returns the Play after assign state (enabled or disabled)
for the Compile Settings.
ENVironment:COMPile:SRATe Sets or returns the sampling rate for the compile settings.
ENVironment:COMPile:SRATe:AUTO Sets or returns the value that indicates if the sampling rate will
be automatically calculated at compile time.
ENVironment:SFORmat Sets or returns the signal format of the signal to be compiled for
all scenarios.
Scenario commands
These commands affect the scenarios. Some are specific to the s elected scenario.
Table 2-3: Scenario commands
Item Description
ENVironment:SCENario:ADD Creates and adds the named scenario to the Environment
Scenarios list. The Scenario is created using the default settings
and is added to the end of the existing Environment Scenarios
list.
ENVironment:SCENario:AMPLitude Sets or returns the peak to peak baseband amplitude (in volts)
for the selected Scenario.
ENVironment:SCENario:COUNt? Returns the number of Scenario definitions in the Environment
Scenarios list.
2-4 Environment Signals Plug-in Programmer Manual
Commands by Groups
Table 2-3: Scenario commands (cont.)
Item Description
ENVironment:SCENario:DELete Deletes the specified scenario from the Environment Scenarios
list.
ENVironment:SCENario:DURation Sets or returns the manual duration that will be used to create
the signal for the selected Scenario.
ENVironment:SCENario:DURation:AUTO Sets or returns the value that indicates if the duration will be
automatically calculated based on the anchor/emitters at compile
time for the selected Scenario.
ENVironment:SCENario:LIST? Returns a comma separated list of environment scenario names.
ENVironment:SCENario:MAGNitude Sets or returns the RF/IF carrier peak Magnitude (in dBm) for
the selected Scenario.
ENVironment:SCENario:REName
ENVironment:SCENario:SELect Sets or returns the selected Scenario in the Environment
Renames the selected scenario name to a new name.
Scenario list. To set the selected Scenario, the name must
currently exist in the Environment Scenario list.
Emitter commands
These commands modify the emitters and parameters within a scenario that are
not specific to an emitter type.
Table 2-4: Emitter commands
Item Description
ENVironment:EMITter:ADD
ENVironment:EMITter:ANCHor Sets or returns the index of the selected anchor emitter in the
ENVironment:EMITter:BOFFset Sets or returns the baseband offset of the selected Emitter when
ENVironment:EMITter:COUNt? This query returns the number of emitter definitions in the
ENVironment:EMITter:DELete
ENVironment:EMITter:DURation
ENVironment:EMITter:FREQuency Sets or returns the RF/IF center Frequency for the selected
ENVironment:EMITter:NAME
ENVironment:EMITter:POFFset Sets or returns the Phase Offset value for the selected Emitter.
ENVironment:EMITter:POWer Sets or returns the power of the selected Emitter.
Adds a new emitter to the selected Environment Scenario.
selected Scenario.
the signal format is set to IQ.
selected Scenario.
Deletes the emitter definition at the specified index of the
selected Scenario.
Sets or returns the duration of the currently selected emitter
definition.
Emitter of the selected Scenario.
Sets or returns the user defined name of the selected emitter
definition.
Environment Signals Plug-in Programmer Manual 2-5
Commands by Groups
Table 2-4: Emitter commands (cont.)
Item Description
ENVironment:EMITter:REPeat
ENVironment:EMITter:SELect Sets or returns the index of the selected emitter definition in the
ENVironment:EMITter:STIMe Sets or r eturns the Start Time of the selected Emitter.
ENVironment:EMITter:TON Sets or returns whether the currently selected emitter is enabled
ENVironment:EMITter:TYPe
Sets or returns whether the currently selected emitter will repeat
the signal an integer number of times to match the Scenario
Duration.
selected Scenario.
or disabled.
Sets or returns the type of the emitter at the selected index of
the selected scenario.
Analog modulation emitter commands
Table 2-5: Analog modulation commands
Item Description
ENVironment:AMODulation:AMModulation:AMINdex Sets or returns the AM Index for the AM Modulation for the
selected Analog Modulation emitter.
ENVironment:AMODulation:FMModulation:FDEViation Sets or returns the Frequency Deviation for the FM Modulation
for the selected Analog Modulation emitter.
ENVironment:AMODulation:MFRequency Sets or returns the Modulating Frequency of the sinusoidal,
triangular, or square Modulating Signals for the selected Analog
Modulation e mitter.
ENVironment:AMODulation:MSIGnal:FNAMe Sets or returns the file name for User Defined Modulating Signal
for the selected Analog Modulation emitter.
ENVironment:AMODulation:MSIGnal:INTerpolation Sets or returns the Interpolation type for User Defined Modulating
Signal for the selected Analog Modulation emitter.
ENVironment:AMODulation:MSIGnal:POFFset Sets or returns the Phase Offset of the sinusoidal, triangular, or
square Modulating Signals for the selected Analog Modulation
emitter.
ENVironment:AMODulation:MSIGnal:SRATe Sets or returns the Sampling Rate for User Defined Modulating
Signal for the selected Analog Modulation emitter.
ENVironment:AMODulation:MSIGnal:TYPe Sets or returns the Modulating Signal type for Analog Modulation
for the selected Analog Modulation emitter.
ENVironment:AMODulation:NOCYcles Sets or returns the Number of cycles of the modulating signal for
the selected Analog Modulation emitter. The signal type must be
sinusoidal, triangular or square.
ENVironment:AMODulation:PMModulation:PDEViation Sets or returns the Phase Deviation for the PM Modulation for
the selected Analog Modulation emitter.
ENVironment:AMODulation:TYPE Sets or returns the Analog Modulation type for the selected
Analog Modulation emitter.
2-6 Environment Signals Plug-in Programmer Manual
Commands by Groups
Bluetooth emitter commands
Table 2-6: Bluetooth commands
Item Description
ENVironment:BLUetooth:DATarate? Returns the Datarate for the selected Bluetooth emitter.
ENVironment:BLUetooth:MODulation? Returns the Modulation type for the selected Bluetooth emitter.
ENVironment:BLUetooth:STANdard Sets or returns the Standard for the selected Bluetooth emitter.
CDMA emitter commands
Table 2-7: CDMA commands
Item Description
ENVironment:CDMA:DRAte Sets or r eturns the Data rate for the selected CDMA emitter.
ENVironment:CDMA:LINK Sets or returns the Link mode for the selected CDMA emitter.
ENVironment:CDMA:NCHannels Sets or returns the number of channels for the selected CDMA
emitter.
ENVironment:CDMA:RCONfiguration Sets or returns the Radio Configuration for the selected CDMA
emitter.
Digital modulation e mitter commands
Table 2-8: Digital modulation commands
Item Description
ENVironment:DMODulation:APSK Sets or returns the APSK Modulation type for the selected Digital
Modulation e mitter.
ENVironment:DMODulation:APSK:PROTation Sets or returns the Phase Rotation of the selected APSK Ring
Index for the selected Digital Modulation emitter.
ENVironment:DMODulation:APSK:RADius Sets or returns the R adius of the selected APSK Ring Index for
the selected Digital Modulation emitter.
ENVironment:DMODulation:APSK:SRINg Sets or returns the selected APSK Ring Index for the selected
Digital M odulation emitter.
ENVironment:DMODulation:APSK:SYMBols Sets or returns the Number of Symbols of the selected APSK
Ring Index for the selected Digital Modulation emitter.
ENVironment:DMODulation:ASK:MINDex Sets or returns the ASK Mod Index for ASK modulation for the
selected Digital Modulation emitter.
ENVironment:DMODulation:CPM:MINDex Sets or returns the Index for CPM modulation for the selected
Digital M odulation emitter.
ENVironment:DMODulation:DATA Sets or returns the Data Pattern type for the selected Digital
Modulation e mitter.
ENVironment:DMODulation:DATA:CODing Sets or returns the coding type for the selected Digital Modulation
emitter.
Environment Signals Plug-in Programmer Manual 2-7
Commands by Groups
Table 2-8: Digital modulation commands (cont.)
Item Description
ENVironment:DMODulation:DATA:FILE Sets or returns the pattern file and file path for the selected
Digital Modulation emitter.
ENVironment:DMODulation:DATA:PATTern Sets or returns the user defined data pattern for the selected
Digital Modulation emitter.
ENVironment:DMODulation:DATA:PRBS Sets or returns the PBRS data type when the data Pattern is set
to PRBS for the selected Digital Modulation emitter.
ENVironment:DMODulation:DATA:PRBS:UDEFined:
POLYnomial
ENVironment:DMODulation:DATA:PRBS:UDEFined:RESet Resets the User Defined PRBS polynomial expression and shift
ENVironment:DMODulation:DATA:PRBS:UDEFined:SREGister Sets or returns the PRBS Shift register initial value for the User
ENVironment:DMODulation:FILTer:ALPHa Sets or returns the Alpha (filter roll off) value for the selected
ENVironment:DMODulation:FILTer:CLENgth Sets or returns the Filter C onvolution Length in symbols for the
ENVironment:DMODulation:FILTer:FILe Sets or returns the Filter File name and file path for user d efined
ENVironment:DMODulation:FILTer:TYPe Sets or returns the Filter Type for the selected Digital Modulation
ENVironment:DMODulation:FILTer:WINDow:CRIPple Sets or returns the Chebyshev Ripple value when the Filter
ENVironment:DMODulation:FILTer:WINDow:KAISer Sets or returns the Kaiser Parameter when the Filter Window
ENVironment:DMODulation:FILTer:WINDow:TYPE Sets or returns the Filter Window type for the selected Digital
ENVironment:DMODulation:FSK Sets or returns the FSK Modulation type for the selected Digital
ENVironment:DMODulation:FSK:PDEViation Sets or returns the FSK Peak Deviation for the selected Digital
ENVironment:DMODulation:HOPPing:CUSTom:RLISt Sets or returns the Repeat List state (enabled or disabled) for the
ENVironment:DMODulation:HOPPing[:LIST]:ADD Adds a single entry to the end of the Frequency Hop List or the
ENVironment:DMODulation:HOPPing[:LIST]:AOFFset Sets or returns the Amplitude Offset of the currently selected hop
ENVironment:DMODulation:HOPPing[:LIST]:COUNt? Returns the number of hops in the Hop List or the number
Sets or returns the PRBS Polynomial Expression for the User
Defined PRBS for the selected Digital Modulation emitter.
register to their default values for the selected Digital Modulation
emitter.
Defined PRBS for the selected Digital Modulation emitter.
Digital Modulation emitter.
selected Digital Modulation emitter.
filter for the selected Digital Modulation emitter.
emitter.
Window type is Chebyshev Ripple for the selected D igital
Modulation e mitter.
type is Kaiser for the selected Digital Modulation emitter.
Modulation e mitter.
Modulation e mitter.
Modulation e mitter.
Frequency Hop List for the selected Digital Modulation emitter.
Frequency Avoid List for the selected Digital M odulation emitter.
for the selected Digital Modulation emitter.
of entries in the Frequency Avoid List for the selected Digital
Modulation e mitter.
2-8 Environment Signals Plug-in Programmer Manual
Commands by Groups
Table 2-8: Digital modulation commands (cont.)
Item Description
ENVironment:DMODulation:HOPPing[:LIST]:DELete
ENVironment:DMODulation:HOPPing[:LIST]:FOFFset Sets or returns the Frequency Offset (Relative Frequency) of the
ENVironment:DMODulation:HOPPing[:LIST]:FREQuency Sets or returns the Frequency of the currently selected hop in the
ENVironment:DMODulation:HOPPing[:LIST]:HDURation Sets or returns the Hop Duration of the currently selected hop
ENVironment:DMODulation:HOPPing[:LIST]:INSert
ENVironment:DMODulation:HOPPing[:LIST]:SELect Sets or returns the selected Hop number in the Frequency Hop
ENVironment:DMODulation:HOPPing[:LIST]:SSINdex Sets or returns the Symbol Start Index (Symbol Index) of the
ENVironment:DMODulation:HOPPing:PATTern Sets or r eturns the H opping Pattern for the selected Digital
ENVironment:DMODulation:HOPPing:PRBS Sets or returns the Hopping PRBS pattern for the selected Digital
ENVironment:DMODulation:HOPPing:PRBS:UDEFined:
POLYnomial
ENVironment:DMODulation:HOPPing:PRBS:UDEFined:RESet Resets the H opping User Defined PRBS type to its default value
ENVironment:DMODulation:HOPPing:PRBS:UDEFined:
SREGister
ENVironment:DMODulation:HOPPing:RANGe:ALISt[:ENABle] Sets or returns the Frequency Avoid List state (enabled or
ENVironment:DMODulation:HOPPing:RANGe[:FREQuency]:
MAXimum
ENVironment:DMODulation:HOPPing:RANGe[:FREQuency]:
MINimum
ENVironment:DMODulation:HOPPing:RANGe[:FREQuency]:
SPACing
ENVironment:DMODulation:HOPPing:TIME Sets or returns the Hop Time type for the selected Digital
ENVironment:DMODulation:HOPPing:TIME:HPSecond Sets or returns the Hops per Second for the selected Digital
ENVironment:DMODulation:HOPPing:TIME:SPHop Sets or returns the Symbols per Hop for the selected D igital
Removes all entries within the Frequency Hop List or the
Frequency Avoid List for the selected Digital Modulation emitter.
currently selected hop for the selected Digital Modulation emitter.
Frequency Hop List for the selected Digital Modulation emitter.
for the selected Digital Modulation emitter.
Inserts a single entry within the Frequency Hop List or the
Frequency Avoid List for the selected Digital Modulation emitter.
List or the Index number in the Frequency Avoid List for the
selected Digital Modulation emitter.
currently selected hop for the selected Digital Modulation emitter.
Modulation e mitter.
Modulation e mitter.
Sets or returns the Hopping PRBS Polynomial Expression for the
User Defined PRBS for the selected Digital Modulation emitter.
for the selected Digital Modulation emitter.
Sets or returns the Hopping PRBS shift register for the User
Defined PRBS for the selected Digital Modulation emitter.
disabled) for the Pseudo Random Range Hopping Pattern for the
selected Digital Modulation emitter.
Sets or returns the Maximum Frequency value for the Pseudo
Random Range Hopping Pattern for the selected Digital
Modulation e mitter.
Sets or returns the Minimum Frequency value for the Pseudo
Random Range Hopping Pattern for the selected Digital
Modulation e mitter.
Sets or returns the Frequency Spacing value for the Pseudo
Random Range Hopping Pattern for the selected Digital
Modulation e mitter.
Modulation e mitter.
Modulation e mitter.
Modulation e mitter.
Environment Signals Plug-in Programmer Manual 2-9
Commands by Groups
Table 2-8: Digital modulation commands (cont.)
Item Description
ENVironment:DMODulation:HOPPing:TON Sets or returns the Hopping state (enabled or disabled) for the
selected Digital Modulation emitter.
ENVironment:DMODulation:NDPSK:INDex Sets or returns the ‘n’ value (the kind of D PSK) for nDPSK
modulation for the selected Digital Modulation emitter.
ENVironment:DMODulation:NDPSK:PROTation Sets or returns the Phase Rotation of nDPSK modulation for the
selected Digital Modulation emitter.
ENVironment:DMODulation:PRAMp:DTYPe Sets or returns the Duration Units used for the Power Ramp table
for the selected Digital Modulation emitter.
ENVironment:DMODulation:PRAMp:DURation Sets or returns the Power Ramp Duration for the selected Digital
Modulation e mitter.
ENVironment:DMODulation:PRAMp:FUNCtion Sets or returns the Power Ramp Function for the selected Digital
Modulation e mitter.
ENVironment:DMODulation:PRAMp:ILEVel Sets or returns the Power Ramp Initial Level of the currently
selected hop for the selected Digital Modulation emitter.
ENVironment:DMODulation:PRAMp:LEVel:ADD Adds new entries to the Power Ramp table for the selected
Digital Modulation emitter.
ENVironment:DMODulation:PRAMp:LEVel:DELete Deletes entries from the Power Ramp table for the selected
Digital Modulation emitter.
ENVironment:DMODulation:PRAMp:LEVel:DURation Sets or returns the Duration of the currently selected Power
Ramp table index for the selected Digital Modulation emitter.
ENVironment:DMODulation:PRAMp:LEVel:ESYMbol Sets or returns the End Symbol of the currently selected Power
Ramp table index for the selected Digital Modulation emitter.
ENVironment:DMODulation:PRAMp:LEVel:POWer Sets or returns the Power Level of the currently selected Power
Ramp table index for the selected Digital Modulation emitter.
ENVironment:DMODulation:PRAMp:LEVel:SELect Sets or returns the selected index (row) of the Power Ramp table
for the selected Digital Modulation emitter.
ENVironment:DMODulation:PRAMp:LEVel:SSYMbol Sets or returns the Start Symbol of the currently selected Power
Ramp table index for the selected Digital Modulation emitter.
ENVironment:DMODulation:PRAMp:PEXTend Sets or returns the Periodic Extend Power Levels state (enabled
or disabled) for the Power Ramp table for the selected Digital
Modulation e mitter.
ENVironment:DMODulation:PRAMp:TON Sets or returns the Power Ramp state (enabled or disabled) for
the selected Digital Modulation emitter.
ENVironment:DMODulation:PSK Sets or returns the PSK modulation type for the selected Digital
Modulation e mitter.
ENVironment:DMODulation:QAM Sets or returns the QAM Modulation type for the selected Digital
Modulation e mitter.
ENVironment:DMODulation:SRATe Sets or returns the Digital Modulation Symbol Rate for the
selected Digital Modulation emitter.
ENVironment:DMODulation:TYPe Sets or returns the digital modulation type for the selected Digital
Modulation e mitter.
2-10 Environment Signals Plug-in Programmer Manual
Commands by Groups
DVB-T emitter commands
Table 2-9: DVB-T commands
Item Description
ENVironment:DVBT:ALPHa? Sets or returns the Alpha value for the selected DVB-T emitter.
ENVironment
ENVironmen
ENVironment:DVBT:MODE Sets or returns the Mode for the selected DVB-T emitter.
ENVironment:DVBT:MODulation Sets or returns the Modulation type for the selected DVB-T
ENVironment:DVBT:TRANsmission
:DVBT:BA NDwidth
t:DVBT:IN Terleaver
Sets or returns the Bandwidth for the selected DVB-T emitter.
Sets or returns the Interleaver for the selected DVB-T emitter.
emitter.
Sets or returns the Transmission type for the selected DVB-T
emitter.
GSM emitter commands
Table 2-10: GSM commands
Item Description
ENVironment:GSM:ARFCN? Returns the ARFCN value for the selected GSM emitter.
ENVironment:GSM:FBANd Sets or returns the Frequency Band for the selected GSM emitter.
ENVironment:GSM:MODulation Sets or returns the Modulation for the selected GSM emitter.
ENVironment:GSM:RFORmat Sets or returns the Radio Format for the selected GSM emitter.
ENVironment:GSM:TDEVice Sets or returns the Transmit Device for the selected GSM emitter.
ENVironment:GSM:TSBType Sets or returns the Timeslot Burst Type for the selected GSM
emitter.
ENVironment:GSM:TSConfiguration Sets or returns the Timeslot Configuration for the selected GSM
itter.
em
NVironment:GSM:TSTMode
E
ets or returns the Timeslot Timing M ode for the selected GSM
S
emitter.
TE emitter commands
L
Table 2-11: LTE commands
Item Description
ENVironment:LTE:BWIDth
ENVironment:LTE:CAGGrigation Sets or returns the Carrier Aggregation state (enabled or
ENVironment:LTE:CBANdwidth[n] Sets or returns the Carrier Bandwidth value of the specified
ENVironment:LTE:COFFset[n] Sets or returns the Carrier Offset value of the specified additional
Sets or returns the Bandwidth for the selected LTE emitter.
disabled) for the selected LTE emitter.
additional carrier for the selected LTE emitter.
carrier for the selected LTE emitter.
Environment Signals Plug-in Programmer Manual 2-11
Commands by Groups
Table 2-11: LTE commands (cont.)
Item Description
ENVironment:LTE:DTYPe
ENVironment:LTE:NACarriers Sets or returns the Number of Additional Carriers for the selected
ENVironment:LTE:TRANsmission
ENVironment:LTE:UDLConfig Sets or returns the Up-Down Link Configuration type for the
Sets or returns the Duplexing type for the selected LTE emitter.
LTE emitter.
Sets or returns the transmission type for the selected LTE emitter.
selected LTE emitter.
Noise emitter commands
Table 2-12: Noise commands
Item Description
ENVironment:NOISe:BANDwidth Sets or returns the Noise Type for the selected Noise emitter.
ENVironment:NOISe:DTYPe Sets or returns the Noise Duration Type for the selected Noise
emitter.
ENVironment:NOISe:TYPE Sets or returns the Noise Type for the selected Noise emitter.
ENVironment:NOISe:UDDUration:VALUe Sets or returns the User defined duration value for the selected
Noise emitter.
OFDM emitter commands
Table 2-13: OFDM frame commands
Item Description
ENVironment:OFDM:FRAMe:BANDwidth Sets or returns the frame’s Bandwidth for the selected OFDM
emitter.
ENVironment:OFDM:FRAMe:HEADer:ADD Adds a row to the end of the frame’s Header Symbols table for
the selected OFDM emitter.
ENVironment:OFDM:FRAMe:HEADer:DELete Deletes the specified row from the frame’s Header symbols table
for the selected OFDM emitter.
ENVironment:OFDM:FRAMe:HEADer:DOMain Sets or returns the frame’s Domain for the user supplied header
file for the selected OFDM emitter.
ENVironment:OFDM:FRAMe:HEADer:MODE Sets or r eturns the H eader input method (file or custom symbols
table) for the selected OFDM emitter.
ENVironment:OFDM:FRAMe:HEADer:PATH Sets or returns the Header file name and file path for the selected
OFDM emitter.
ENVironment:OFDM:FRAMe:HEADer:REPeat Sets or returns the Repeat count for the user supplied header file
for the selected OFDM emitter.
ENVironment:OFDM:FRAMe:HEADer:SELect Sets or returns the selected (active) row from the Header’s
symbols table for the selected OFDM emitter. Other commands
act on the selected row.
2-12 Environment Signals Plug-in Programmer Manual
Commands by Groups
Table 2-13: OFDM frame commands (cont.)
Item Description
ENVironment:OFDM:FRAMe:HEADer:SNAMe Sets or returns the symbol name for the currently selected row
in the Header symbol table for the selected OFDM emitter. The
new name must already exist in the Symbol List.
ENVironment:OFDM:FRAMe:HEADer:SRATe Sets or returns the frame’s Sampling Rate for the user supplied
header file for the selected OFDM emitter.
ENVironment:OFDM:FRAMe:HEADer:SREPeat Sets or returns the Repeat count for the currently selected row in
the frame’s Header symbols table for the selected OFDM emitter.
ENVironment:OFDM:FRAMe:HEADer:SSPacing Sets or returns the Header Subcarriers Spacing for the user
supplied header file for the selected OFDM emitter.
ENVironment:OFDM:FRAMe:HEADer:TON Sets or returns the status (enabled or disabled) of the frame’s
Header for the selected OFDM emitter.
ENVironment:OFDM:FRAMe:HOPPing:ENABle Sets or returns the Hopping state (enabled or disabled) for the
selected O FDM em itter.
ENVironment:OFDM:FRAMe:HOPPing:HTIMe Sets or returns the frame’s Hop Time type for the selected OFDM
emitter.
ENVironment:OFDM:FRAMe:HOPPing[:LIST]:ADD Adds a single entry to the end of the frame’s Frequency Hop List
for the selected OFDM emitter.
ENVironment:OFDM:FRAMe:HOPPing[:LIST]:AOFFset Sets or returns the Amplitude Offset of the selected hop in the
frame’s Frequency Hop List for the selected OFDM emitter.
ENVironment:OFDM:FRAMe:HOPPing[:LIST]:COUNt? Returns the number of hops in the frame’s Hop List for the
selected O FDM em itter.
ENVironment:OFDM:FRAMe:HOPPing[:LIST]:DELete Removes entries from the frame’s Frequency Hop List for the
selected O FDM em itter
ENVironment:OFDM:FRAMe:HOPPing[:LIST]:FREQuency Sets or returns the Frequency of the selected hop in the frame’s
Frequency Hop List for the selected OFDM emitter.
ENVironment:OFDM:FRAMe:HOPPing[:LIST]:INSert Inserts a single entry into the frame’s Frequency H op List above
the specified index for the selected OFDM emitter.
ENVironment:OFDM:FRAMe:HOPPing[:LIST]:RFRequency Sets or returns the Frequency Offset (Relative Frequency) of the
selected hop in the frame’s Frequency Hop List for the selected
OFDM emitter.
ENVironment:OFDM:FRAMe:HOPPing[:LIST]:SELect Sets or returns the selected Hop number in the frame’s
Frequency Hop List for the selected frame in the Frame List for
the selected OFDM em itter.
ENVironment:OFDM:FRAMe:HOPPing[:LIST]:SSINdex Sets or returns the frame’s Symbol Start Index (Symbol Index)
for the selected OFDM emitter.
ENVironment:OFDM:FRAMe:HOPPing:RLISt Sets or returns the frame’s Repeat List state (enabled or
disabled) for the Frequency Hop List for the selected OFDM
emitter.
ENVironment:OFDM:FRAMe:HOPPing:SPHop Sets or returns the frame’s Symbols per Hop for the selected
OFDM emitter.
ENVironment:OFDM:FRAMe:OTIMe Sets or returns the frame’s Off-Time duration for the selected
OFDM emitter.
Environment Signals Plug-in Programmer Manual 2-13
Commands by Groups
Table 2-13: OFDM frame commands (cont.)
Item Description
ENVironment:OFDM:FRAMe:PAYLoad:ADD Adds a row to the end of the Payload symbols table for the
selected O FDM em itter.
ENVironment:OFDM:FRAMe:PAYLoad:DELete Deletes the specified row from the Payload symbols table for the
selected O FDM em itter.
ENVironment:OFDM:FRAMe:PAYLoad:SELect Sets or returns the selected (active) row from the Payload
symbols table for the selected OFDM emitter. Other commands
act on the selected row.
ENVironment:OFDM:FRAMe:PAYLoad:SNAMe Sets or returns the symbol name for the currently selected row in
the Payload symbol table for the selected OFDM emitter. The
new name must already exist in the Symbol List.
ENVironment:OFDM:FRAMe:PAYLoad:SREPeat Sets or returns the repeat count for the currently selected row in
the Payload symbols table for the selected OFDM emitter.
ENVironment:OFDM:FRAMe:PAYLoad:TON Sets or returns the status (enabled or disabled) of the frame
Payload for the selected OFDM emitter.
ENVironment:OFDM:FRAMe:PREamble[n]:DOMain Sets or returns the Domain type of the specified Preamble for the
selected O FDM em itter.
ENVironment:OFDM:FRAMe:PREamble[n]:ENABle Sets or returns the status of the specified Preamble (enabled or
disabled) for the selected OFDM emitter.
ENVironment:OFDM:FRAMe:PREamble[n]:PATH Sets or returns the specified Preamble file name and file path
for the selected OFDM emitter.
ENVironment:OFDM:FRAMe:PREamble[n]:REPeat Sets or returns the Repeat count of the specified P reamble for
the selected OFDM emitter.
ENVironment:OFDM:FRAMe:PREamble[n]:SRATe Sets or returns the Sampling Rate of the specified Preamble
for the selected OFDM emitter.
ENVironment:OFDM:FRAMe:PREamble[n]:SSPacing Sets or returns the Subcarrier Spacing of the specified P reamble
for the selected OFDM emitter.
ENVironment:OFDM:FRAMe:PTON Sets or returns the status (enabled or disabled) of including a
Preamble for the selected OFDM emitter.
Table 2-14: OFDM symbols commands
Item Description
ENVironment:OFDM:SYMBol:ADD Adds a new symbol to the existing list of symbols within the
Symbols List for the selected OFDM emitter.
ENVironment:OFDM:SYMBol:APPRofile:CUSTom:ADD Adds a single row to the custom Amplitude/Phase Profile table
for the selected symbol in the Symbol List for the selected OFDM
emitter.
ENVironment:OFDM:SYMBol:APPRofile:CUSTom:AMPLitude Sets or returns the amplitude of the subcarrier positions of the
selected row in the Custom A mplitude/Phase Profile table for
the selected symbol in the Symbol List for the selected OFDM
emitter.
2-14 Environment Signals Plug-in Programmer Manual
Commands by Groups
Table 2-14: OFDM symbols commands (cont.)
Item Description
ENVironment:OFDM:SYMBol:APPRofile:CUSTom:PHASe Sets or returns the phase of the subcarrier positions of the
selected row in the Custom Amplitude/Phase Pro file table for
the selected symbol in the Symbol List for the selected OFDM
emitter.
ENVironment:OFDM:SYMBol:APPRofile:CUSTom:REMove Removes the specified row from the custom Amplitude/Phase
Profile table for the selected symbol in the Symbol List for the
selected O FDM em itter.
ENVironment:OFDM:SYMBol:APPRofile:CUSTom:SELect Sets or returns the selected (active) row of the Custom
Amplitude/Phase Profile table for the selected OFDM emitter.
ENVironment:OFDM:SYMBol:APPRofile:CUSTom:SPOS Sets or returns the subcarrier positions for the currently selected
row in the custom Amplitude/Phase Profile table for the selected
symbol in the Symbol List for the selected OFDM emitter.
ENVironment:OFDM:SYMBol:APPRofile:DATA:AMPLitude Sets or returns the amplitude of the Data subcarriers when
configuring the Amplitude/Phase Pro file for the selected symbol
in the Symbol List for the selected OFDM emitter.
ENVironment:OFDM:SYMBol:APPRofile:DATA:ENABle Sets or returns the Data state (enabled or disabled) of the
Amplitude/Phase Profile for the selected symbol in the Symbol
List for the selected OFDM emitter.
ENVironment:OFDM:SYMBol:APPRofile:DATA:PHASe Sets or returns the phase o f the Data subcarriers when
configuring the Amplitude/Phase Pro file for the selected symbol
in the Symbol List for the selected OFDM emitter.
ENVironment:OFDM:SYMBol:APPRofile:ENABle Sets or returns the Amplitude Phase Profile state (enabled or
disabled) for the selected symbol in the Symbol List for the
selected O FDM em itter.
ENVironment:OFDM:SYMBol:APPRofile:PILot:AMPLitude Sets or returns the amplitude of the Pilot subcarriers when
configuring the Amplitude/Phase Pro file for the selected symbol
in the Symbol List for the selected OFDM emitter.
ENVironment:OFDM:SYMBol:APPRofile:PILot:ENABle Sets or returns the Pilot state (enabled or disabled) of the
Amplitude/Phase Profile for the selected symbol in the Symbol
List for the selected OFDM emitter.
ENVironment:OFDM:SYMBol:APPRofile:PILot:PHASe Sets or returns the Phase o f the Pilot subcarriers when
configuring the Amplitude/Phase Pro file for the selected symbol
in the Symbol List for the selected OFDM emitter.
ENVironment:OFDM:SYMBol:APPRofile:TYPE Sets or returns the Amplitude Phase Profile type for selected
symbol for the selected OFDM emitter.
ENVironment:OFDM:SYMBol:CRATio:ENABle Sets or returns the symbol’s Clipping Ratio state (enabled or
disabled) for the selected OFDM emitter.
ENVironment:OFDM:SYMBol:CRATio:VALue Sets or returns the symbol’s Clipping Ratio value for the selected
OFDM emitter.
ENVironment:OFDM:SYMBol:DATA Sets or returns the symbol Data subcarriers pattern type for the
selected O FDM em itter.
ENVironment:OFDM:SYMBol:DATA:ENABle Sets or returns the symbol Data subcarriers state (enabled or
disabled) for the selected OFDM emitter.
Environment Signals Plug-in Programmer Manual 2-15
Commands by Groups
Table 2-14: OFDM symbols commands (cont.)
Item Description
ENVironment:OFDM:SYMBol:DATA:FILE Sets or returns the symbol Data Pattern filename and filepath
for the selected OFDM emitter.
ENVironment:OFDM:SYMBol:DATA:MODulation:PSK Sets or returns the symbol Data subcarriers PSK modulation
type for the selected OFDM emitter.
ENVironment:OFDM:SYMBol:DATA:MODulation:QAM Sets or returns the symbol Data subcarriers QAM modulation
type for the selected OFDM emitter.
ENVironment:OFDM:SYMBol:DATA:MODulation:TYPe Sets or returns the symbol Data subcarriers modulation type
for the selected OFDM emitter.
ENVironment:OFDM:SYMBol:DATA:PATTern Sets or returns the symbol user defined Data subcarriers pattern
for the selected OFDM emitter.
ENVironment:OFDM:SYMBol:DATA:POSition Sets or returns the symbol Data subcarrier positions for the
selected O FDM em itter.
ENVironment:OFDM:SYMBol:DATA:PRBS Sets or returns the P RBS pattern type when the symbol Data
subcarriers pattern type is set to PRBS for the selected OFDM
emitter.
ENVironment:OFDM:SYMBol:DATA:PRBS:UDEFined:
POLYnomial
ENVironment:OFDM:SYMBol:DATA:PRBS:UDEFined:
SREGister
ENVironment:OFDM:SYMBol:DELete Deletes the specified symbol from the Symbol List for the
ENVironment:OFDM:SYMBol:FOFFset:ENABle Sets or returns the symbol’s Frequency Offset state (enabled or
ENVironment:OFDM:SYMBol:FOFFset:VALue Sets or returns the symbol’s Frequency Offset value for the
ENVironment:OFDM:SYMBol:GINTe rval:ENA Ble Sets or returns the symbol’s Guard Interval state (enabled or
ENVironment:OFDM:SYMBol:GINTerval:TYPE Sets or returns the symbol’s Guard Interval type for the selected
ENVironment:OFDM:SYMBol:GINTerval:VALue Sets or returns the value of the guard interval for the selected
ENVironment:OFDM:SYMBol:GPOSitions Sets or returns the symbol’s Subcarrier Guard positions for the
ENVironment:OFDM:SYMBol:GPOSitions:ENABle Sets or returns the symbol’s Subcarriers Guard positions state
ENVironment:OFDM:SYMBol:NPOSitions Sets or returns the symbol’s Subcarrier Null positions for the
ENVironment:OFDM:SYMBol:NPOSitions:ENABle Sets or returns the Subcarrier Null positions state (enabled or
Sets or returns the symbol PRBS Polynomial Expression for the
User Defined PRBS when the Data subcarriers pattern is set to
User Defined PRBS for the selected OFDM emitter.
Sets or returns the symbol PRBS Shift register initial value for
the User Defined PRBS when the Data subcarriers pattern is set
to User Defined PRBS for the selected OFDM emitter.
selected O FDM em itter.
disabled) for the selected OFDM emitter.
selected O FDM em itter.
disabled) for the selected OFDM emitter.
OFDM emitter.
symbol in the Symbol List for the selected OFDM emitter.
selected O FDM em itter.
(enabled or disabled) for the selected OFDM emitter.
selected O FDM em itter.
disabled) for the selected symbol in the Symbol List for the
selected O FDM em itter.
2-16 Environment Signals Plug-in Programmer Manual
Commands by Groups
Table 2-14: OFDM symbols commands (cont.)
Item Description
ENVironment:OFDM:SYMBol:PILot Sets or returns the symbol Pilot s ubcarriers pattern type for the
selected O FDM em itter.
ENVironment:OFDM:SYMBol:PILot:ENABle Sets or returns the symbol Pilot subcarriers state (enabled or
disabled) for the selected OFDM emitter.
ENVironment:OFDM:SYMBol:PILot:FILE Sets or returns the symbol Pilot subcarriers pattern fi le name and
file path for the selected OFDM emitter.
ENVironment:OFDM:SYMBol:PILot:MODulation:PSK Sets or returns the symbol’s Pilot subcarriers PSK modulation
type for the selected OFDM emitter.
ENVironment:OFDM:SYMBol:PILot:MODulation:QAM Sets or returns the symbol’s Pilot subcarriers QAM modulation
type for the selected OFDM emitter.
ENVironment:OFDM:SYMBol:PILot:MODulation:TYPe Sets or returns the symbol’s Pilot subcarriers modulation type
for the selected OFDM emitter.
ENVironment:OFDM:SYMBol:PILot:PATTern Sets or returns the user defined pattern for the symbol’s Pilot
subcarrier for the selected OFDM emitter.
ENVironment:OFDM:SYMBol:PILot:POSition Sets or returns the symbol’s Pilot subcarrier positions for the
selected O FDM emitter.
ENVironment:OFDM:SYMBol:PILot:PRBS Sets or returns the PRBS pattern type when the Pilot s ubcarriers
pattern type is set to PRBS for the selected OFDM emitter.
ENVironment:OFDM:SYMBol:PILot:PRBS:UDEFined:
POLYnomial
ENVironment:OFDM:SYMBol:PILot:PRBS:UDEFined:SREGister Sets or returns the PRBS Shift register initial value for the User
ENVironment:OFDM:SYMBol:POFFset:ENABle Sets or returns the symbol’s Phase Offset state (enabled or
ENVironment:OFDM:SYMBol:POFFset:VALue Sets or returns the symbol’s Phase Offset value for the selected
ENVironment:OFDM:SYMBol:REName Renames an existing symbol name to a new name for the
ENVironment:OFDM:SYMBol:SELect Sets or returns the selected symbol from the list of available
ENVironment:OFDM:SYMBol:SSPacing Sets or returns the Symbols Subcarriers Spacing for the selected
ENVironment:OFDM:SYMBol:TSUBcarriers Sets or returns the total number of symbol subcarriers for the
ENVironment:OFDM:SYMBol:TSUBcarriers:POSitions Sets or returns if the symbol subcarriers show only the positive
Sets or returns the PRBS Polynomial Expression for the User
Defined PRBS when the symbol Pilot subcarriers pattern is set to
User Defined PRBS for the selected OFDM emitter.
Defined PRBS when the symbol Pilot subcarriers pattern is set to
User Defined PRBS for the selected symbol in the Symbol List
for the selected OFDM emitter.
disabled) for the selected OFDM emitter.
OFDM emitter.
selected OFDM emitter. The symbol being renamed must exist
in the Symbol List.
symbols in the Symbol List for the selected OFDM emitter.
OFDM emitter.
selected O FDM em itter.
subcarriers or all subcarriers for the selected OFDM emitter.
Environment Signals Plug-in Programmer Manual 2-17
Commands by Groups
Table 2-14: OFDM symbols commands (cont.)
Item Description
ENVironment:OFDM:SYMBol:UDEFined:ENABle Sets or returns the symbol User-de fined frequency weight
(enabled or disabled) for the selected OFDM emitter.
ENVironment:OFDM:SYMBol:UDEFined:PATH Sets or returns the file name and file path of the User Defined
Weights File of the selected symbol in the Symbol List for the
selected O FDM em itter.
P25 emitter commands
Table 2-15: P25 commands
Item Description
ENVironment:P25:MODulation Sets or returns the Modulation for the selected P25 emitter.
ENVironment:P25:STANdard Sets or returns the Standard for the s elected P25 emitter.
Pulse emitter commands
Table 2-16: Pulse commands
Item Description
ENVironment:PULSe:PRI Sets or returns the PRI (Pulse Repetition Interval) for the
selected Pulse emitter.
ENVironment:PULSe:RCOunt Sets or returns the Pulse repeat count for the selected Pulse
emitter.
ENVironment:PULSe:WIDTh Sets or returns the Pulse Width for the s elected Pulse emitter.
Radar emitter commands
Table 2-17: Radar antenna commands
Item Description
ENVironment:RADar:ANTenna:BEAM:AZIMuth
ENVironment:RADar:ANTenna:BEAM:ELEVation
ENVironment:RADar:ANTenna:BEAM:TYPE
ENVironment:RADar:ANTenna:SCAN:AREA Sets or returns the Antenna Scan Area for the selected Radar
ENVironment:RADar:ANTenna:SCAN:FILE Sets or returns the file path to the Antenna Custom Scan File
Sets or returns the Antenna Beam Azimuth for the selected
Radar emitter.
Sets or returns the Antenna Beam Elevation for the selected
Radar emitter.
Sets or returns the Antenna Beam Type for the selected Radar
emitter.
emitter.
for the selected Radar emitter.
2-18 Environment Signals Plug-in Programmer Manual