Tektronix DSA70404B Data Sheet

Digital Phosphor Oscilloscopes/Digital Serial Analyzers

DPO/DSA70000B Series Data Sheet

DPX and Fast Acquisition - Quickly find intermittent e vents with the
industry’s highest waveform capture rate

Long Record Lengths – Capture long-term trends or infrequent events
then analyze the entire acquired record with built-in measurements

P7500 TriMode™ Probing System - Perfectly matched signal
connectivity from 4 GHz to 20 GHz

Application Support – Enables standard-specificcertification,
measurement automation, and ease of use

Serial Data Link Analysis (SDL A) - For high-speed serial data streams,
emulate and equalize the channel as well as de-embedding the fixture.

Applications

Signal Integrity, Jitter, and Timing Analysis

Verifi cation, Debug, Characterization, or Ce rti fication of Sophisticated
Designs

Feature

On All Four Channels Simultaneously

Highes
high-speed serial standards

Superior Signal Integrity and Excellent Signal-to-Noise Ratio – Observe
the truest representation of your waveform

Pinpoint®Triggering – M inimize time spen t trying to acquire problem
signals for efficient troubleshooting and shortened debug time

5 Gbps R
of a specified NRZ or 8b/10b pattern to allow isolation of pattern
dependent effect s

Search & Mark – Provides waveform pattern matching and software
trigg

s & Benefits

20, 16, 12.5, 8, 6 , and 4 GHz Bandwidth Models
Up to 50 GS/s Real-Time Sample Rate
Up to 250
Feature for Quick Navigation
Fastest Waveform Capture Rate with >300,000 wfms/s Maximum per
Channel

ers for signals of interest

Megasamples Record Length with MultiView Zoom™

t Bandwidth – Up to 20 GHz enables measurement on the latest

eal-time Serial Trigger – Assures triggering on the first instance

Debugging and Compliance Testing of Se rial Data Streams for Industry
Standards

Memory Bus Analysis

Switching Power Supply Verification

Investigation of Transient Phenomena

Spectral Analysis of Transient or Wide-bandwidth RF Signals

Unmatched Performance for Greater Insight
Gets Your Work Done Faster

The DPO70000B and the DSA70000B Series real-time digital phosphor
oscilloscopes are the industry’s best solution to the challenging signal
integrity issues faced by designers verifying, characterizing, debugging,
and testing sophisticated electronic designs. The specialized DSA70000B
Series provides a complete and dedicated solution to address the
challenges of high-speed serial designs.

The family features exceptional performance in signal acquisition and
analysis, operational simplicity, and unmatched debugging tools to
accelerate your day-to-day tasks. A large display and the intuitive user

ace provide easy access to the maximum amount of information.

interf

Data Sheet

Unmatched Acquisition Performance

Superior Signal Integrity and Excellent Signal-to-Noise
Ratio of the DP
Ensures Confidence in Your Measurement Results

High bandwidth up to 20 GHz matched across 2, 3, or 4 channels
and enabled b
user-selectable filter for each channel provides magnitude and phase
correction for more accurate representation of extremely fast signals.
In addition,
enhancement for applications needing the highest measurement
throughput.

Bandwidth enhancement eliminates imperfections in frequency response
all the way t

Simultaneo
details (transients, imperfections, fast edges)

50 GS/s on all channels for the 12.5, 16, and 20 GHz models
25 GS/s on a

With high s
DPO70000B and DSA70000B series enable you to perform precise
characterization measurements. When debugging a DUT, a low noise

floor and m
finding the smallest anomalies that might affect the DUT’s performance.

For RF signal verification, a lower noise floor translates into a higher
dynamic r
applications.

Lowest jitter noise floor and highest vertical accuracy provide additional
margin in your measurement s.

Long record length provides high resolution and extended-duration

rm capture

wavefo

Standard 10 M samples per channel on the DPO70000B Series and
20 M on the DSA70000B Series
Option
8GHzmodels
Optional up to 250 M samples on all four channels for the 12.5, 16,
and 20
MultiView Zoom helps you manage long records, compare and
analyze multiple waveform segments

Widest Range of Probing Solutions – Whether you need to measure

serial data or switching currents from your new power supply

8 Gbps
design, Tektronix offers a vast array of probing solutions, including active
single ended, differential, high voltage, current, optical, and a wide range

obe and oscilloscope accessories.

of pr

O70000B and D SA70000B Series

y Tektronix proprietary bandwidth enhancement. The

only Tektronix allows the user to disable the bandwidth

o the probe tip

us high sample rate on all channels captures more signal

ll channels for the 4, 6, and 8 GHz models

ignal-to-noise ratio and low internal noise floor, the

aximum signal fidelity of the measurement instrument allows

ange, opening the DPO/DSA70000B for a wider range of

al up to 100 M samples on all four channels f or the 4, 6, and

GHz models

User-selectable bandwidth limiting choices

Zoom in on four areas of interest simultaneously to quickly compare them

2 www.tektronix.com/oscilloscopes

Digital Phosphor Oscilloscopes/Digital Serial Analyzers — DPO/DSA70000B Series

Low-cost solder tip features quick connection so moving probe to various solder points is
fast and easy

Maximize t
FastAcq ac

he probability of capturing elusive glitches and other infrequent events with

quisition mode.

knob you can clearly “see a world others don’t see”, displaying the complete
picture of your circuit’s operation. Some oscilloscope vendors claim high
waveform capture rates for short bursts of time, but only DPO70000B and
DSA70000B oscilloscopes, enabled by DPX technology, can deliver these

eform capture rates on a sustained basis — saving minutes, hours,

fast wav
or even days by quickly revealing the nature of faults so sophisticated
trigger modes can be applied to isolate them.

P7500 TriMode probes simplify complex measurement setups

P7500 TriMode probing system – Perfectly matched to the
DPO/DSA70000B, the P7500 TriMode probes allow you to switch among
differential, single ended, and common-mode measurements without
moving the probe from its connection points. The P7500 series offers
probes for performance from 4 GHz to 20 GHz.

Accelerate the Debug of Comple x Electrical
Designs

FastAcq Acquisition Mode Expedites Debugging by

ly Showing Imperfections

Clear

More than just color-grading, FastAcq’s proprietary DPX®acquisition

ology captures signals at more than 300,000 waveforms per second

techn
on all four channels simultaneously, dramatically increasing the probability
of discovering infrequent fault events. And w ith a simple turn of the intensity

The Abil

ity to Trigger an Oscilloscope on Events of
Interest is Paramount in Complex Signal Debug and
Verification

Whether you’re trying to find a problem signal or need to isolate a section
of a complex signal for further analysis, like a DDR read or write burst.
Tektronix’ Pinpoint

uses Silicon Germanium (SiGe) technology to provide very high

system

®

triggering provides the solution. The Pinpoint trigger

trigger sensitivity with very low trigger jitter and ability to capture very
narrow glitches. Pinpoint triggering allows selection of virtually all trigger
types on both A and B trigger events. Other trigger systems offer multiple
trigger types only on a single event (A event), with delayed trigger (B event)
selection limited to edge type triggering and often do not provide a way

et the trigger se quence if the B event doesn’t occur. But Pinpoint

to res
triggering provides the full suite of advanced trigger types on both A and
B triggers, logic qualification to control when to look for these events,
and reset triggering to begin the trigger sequence again after a specified
time, state, or transition so that even events in the most complex signals
can be captured. Other oscilloscopes typically offer less than 20 trigger

nations; Pinpoint triggering offers over 1400 combinations, all at full

combi
performance.

nhanced Triggering, trigger jitter is reduced to <100 fs. With this

With E
stability at the trigger point, the trigger point can be used as a measurement
reference.

www.tektronix.com/oscilloscopes 3

Data Sheet

riggering can isolate glitches down to 100-ps wide

Pinpoint t

NRZ Pattern Lock Triggering of a 640-bit long SATA serial pattern at 6 Gbps

of a long serial test pattern with outstanding time base accura cy. Pattern
lock triggering can be used to remove random jitter from long serial
data patterns. Effects of specific bit transitions can be investigated, and
averaging can be used with mask testing. This feature supports up to

6.25 Gbps NRZ serial data stream and is standard on the DSA70000B
instruments, or included as part of Option PTH on the DPO70000B models.

Isolate only the valid glitches

col and Serial Pattern Triggering

Proto

To debug serial architectures, use the serial p attern triggering for NRZ serial

tream with built-in clock recovery and correlate events across physical

data s
and link layers. This feature comes standard on the DSA70000B series
and is available on DPO70000B models as Opt. PTH. The instrument can
recover the clock signal, identify transitions, and allow you to set the desired
encoded words for the serial pattern trigger to capture. Opt. PTH and the
DSA70000B Series cover serial standard s up to 3.1 25 Gbps. For highe r bit

tandards like USB 3.0, option PTU on the DPO70000B s e ries and

rate s
option STU on the DSA70000B series extend 8b10b triggering and decode
to5Gbps.

Pattern Lock Triggering adds an extra dimension to NRZ serial pa ttern
triggering by enabling the oscilloscope to take synchronized acquisitions

Large 10-Division XGA Display Screen

The DPO/DSA70000B Series have a large 12.1” (307.3 mm) XGA display
with a touch screen with 10 vertical divisions give you 25% more vertical
measurement resolution than other oscilloscopes.

Unmatched Usability

TekLink™ allows yo u to acquire more than four channels by synchronizing
multiple oscilloscopes and debug multiple-lane h igh-spee d applications
such as PCI Express X16 or DDR memory.

The DPO/DSA70000B Series instruments excel in usability with a s uite of
productivity features, such as a touch screen, flat menu structures, intuitive
graphical icons, knob-per-channel vertical controls, right clicks, mouse
wheel operation, and familiar Windo ws-based controls.

Interoperability with Logic A nalyzers for Digital Design
and Debug

Tektronix’ Integrated View (iView™) data display enables digital designers
to solve signal integrity challenges and effectively debug and verify their
systems more quickly and easily. This integration allows designers to view
time-correlated digital and analog data in the same display window, and

te the analog characteristics of the digital signals t hat are causing

isola
system failures. No user calibration is required. And, once set up, the iView
feature is completely automated.

4 www.tektronix.com/oscilloscopes

3 modes of operation of the horizontal time base

Digital Phosphor Oscilloscopes/Digital Serial Analyzers — DPO/DSA70000B Series

Unmatched

Get the Mos

Versatility

t of Your Oscilloscope by Fully Controlling

its Waveform Acquisition and Display Parameters.

Choose the operation you need to do your job the fastest: Automatic,
Constant Sample Rate, or Manual. When you a re doing signal exploration
and want a lively signal, the default Automatic mode provides you with
the liveliest display update rate. If you want the highest real-time sample
rate that will give you the most measurement accuracy, then the Constant

Sample Ra

provide the best real-time resolution. Finally the Manual mode ensures
direct and independent contro l of the sample rate and record length for
applications requiring specific settings.

te mode is for you. It will maintain the highest sample rate and

With the MyScope®Feature, Create Your Own Control
Windows With Only the Controls, Features, and
Capabilities that You Care About

reate your own personalized "toolbox" of oscilloscope features

Easily c
in a matter of minutes using a simple, visual, drag-and-drop process.
Once created, these custom control windows are easily accessed through
a dedicated MyScope button and menu selection on the oscilloscope
button/menu bar, just like any other control window. You can make an
unlimited number of custom control windows, enabling each person who

e oscilloscope in a shared environment to have their own unique

uses th
control window. MyScope control windows will benefit all oscilloscope
users, eliminating the ramp-up time that many face when returning to the lab
after not using an oscilloscope for a while, and enables t he power user to be

Drag and drop menu items of interest to create the MyScope control window

far more efficient. Everything you need is found in one control window rather
than navigating t hrough multiple menus to repeat similar tasks.

With OpenChoice®Software, Customize Your Test and
Measurement System with Familiar Analysis Tools

The analysis and networking features of Open Choice sof tware add
more flexibility to Tektronix’ Windows XP oscilloscopes: Using the fast
embedded bus, waveform data can be mo ved directly from acquisition

sis applications on the Windows desktop at much faster spe eds

to analy
than conventional GPIB transfers. Tektronix’ implementation of industry
standard protocols, such as TekVISA™ interface and ActiveX controls, are
included for using and enhancing Windows applications for data analysis
and documentation. IVI instrument drivers are included to enable easy
communication with the oscilloscope using GPIB, RS-232, and LAN

ions from programs running on the instrument or an external PC. Or,

connect
use the Software Developer’s Kit (SDK) to help create custom software
to automate multistep processes in waveform collection and analysis with
Visual BASIC, C, C++, MATLAB, LabVIEW, LabWindows/CVI, and other
common Application Development Environments (ADE). Integration of the
oscilloscope with exte rnal PCs and non-Windows hosts is also supported.

tion, the OpenChoice architecture provides a comprehensive

In addi
software infrastructure for faster, more versatile operations. Data transfer
utilities, such as the Excel or Word toolbar plug-ins can be used to simplify
analysis and documentation on the Windows desktop or on an external PC.

www.tektronix.com/oscilloscopes 5

Data Sheet

More Insight into Your Complex Electrical
Design for Characterization and Certification
Testi ng

The DPO/DSA70000B series offers the industry’s most comprehensive
set of analysis and certification tools, such as a simple m at h expression,
waveform mask testing, a pass/fail tests, event searching, an d event
marking. Cust
development environments such as MATLAB
set.

A Wide Range of Built-In Advanced Waveform Analysis
Tools

Waveform cursors make it easy to measure trace-to-trace timing
characteristics, while cursors that link between YT and XY display modes
make it easy to investigate phase relationships and Safe Operating Area
violations.
palette that logically organizes measurements into Amplitude, Time,
Combination, Histogram, and Communications categories. Gather further
insight into your measurement results with statistical data such as mean,
min, max, standard deviation, and population.

Define and apply math expressions to waveform data for on-screen results
in terms that you can use. Access common waveform m ath functions
with the touch of a button. Or, for advanced applications, create algebraic
expression
functions, measurement values, scalars, and user-adjustable variables with
an easy-to-use calculator-style editor.

FFT – To analyze your signal in the frequency domain, use the built-in

spectral an
you can directly control the frequency span, center frequency, reference
level, and resolution bandwidth. Vector signal analysis and Ultra-Wideband
(UWB) verification and characterization are provided as part of the SignalVu
and UWB options.

Filtering – Enhance your ability to isolate or remove a component of your

signal (noise or specific harmonics of the signal) by creating your own
filtersorbyusingthefilters provided as standard with the instrument.

These customizable FIR filters can be used to implement today’s preferred
signal-filtering techniques, including removing signal pre-emphasis or
minimizin
test.

om applications that you develop yourself using application

®

can further extend this tool

Select from 53 automatic measurements using a graphical

s consisting of live waveforms, reference waveforms, math

alysis function. Using the oscilloscope front-panel controls,

g the effects of fixtures and cables connected to the device under

Capture da
reports us

Basic

ta into Microsoft Excel using the unique Excel toolbar, and create custom

ing the Word toolbar

spectral UI control window

6 www.tektronix.com/oscilloscopes

Digital Phosphor Oscilloscopes/Digital Serial Analyzers — DPO/DSA70000B Series

Application Specific Solutions –

Enable standard specificcertification, measurement
automation, and extended signal analysis

DPOJET Jitter And Eye Diagram Analysis (Opt. DJA) – Simplify identifying signal
integrity concerns, jitter, and their related sources with DPOJET software. DPOJET
provides the highest sensitivity and accuracy available for real-time oscilloscopes.

Advanced Event Search and Mark (Opt. ASM) – Ease the tedious task of examining
data by highlighting important events, skipping the unimportant ones, and enhancing
the comprehension of event relationships. Navigate between the events of interest
effortlessly.

DDR Memory Bus Analysis (Opt. DDRA) – Automatically identify DDR1, LP-DDR1,
DDR2, DDR3, and GDDR3 Reads and Writes and clearly see and analyze how analog
anomalies are affecting your DDR/Memory. DDRA with DPOJET, combined with the
DPO/DSA70000B DPX
issues.

®

technology, is the fastest way to solve complex memory signaling

SDLA - Serial Data Link Analysis (options SLE and SLA) – Gain insight into serial
data links with the capability to emulate the serial data channel from its S-parameters,
de-embed the fixture or other network, and add or remove transmitter equalization
(de-emphasis/pre-emphasis). Option SLA adds processing of waveforms with FFE
and DFE equalizations and automatic equalizer training. DPOJET provides advanced
measurement and jitter analysis of the resulting waveforms.

www.tektronix.com/oscilloscopes 7

Data Sheet

DisplayPort Compliance Test Solution (Opt. DSPT) – Support DisplayPort Compliance
Test Standard (CTS) source test with four-line simultaneous testing using the Tektronix
P7300SMA Series probes and DisplayPort software. Detailed test reports with waveform
plots, pass/fail results, and margin analysis are included.

DVI Compliance Test Solution (Opt. DVI) – Obtain quick and dependable results
with the DVI compliance test software. Automated testing based on objective pass/fail
detection without human intervention will dramatically enhance your productivity.

Ethernet Compliance Test Solution (Opt. ET3) – Receive full PHY layer support
for Ethernet variants 10BASE-T, 100BASE-TX, and 1000BASE-T with Tektronix’
comprehensive, integrated Ethernet tool set. Analog verification, automated compliance
software, and device characterization solutions are all included.

8 www.tektronix.com/oscilloscopes

FB-DIMM Compliance Test Solution (Opt. FBD) – Test the Receiver, Transmitter, and
Reference clock test points for compliance as per FB-DIMM standards.

Digital Phosphor Oscilloscopes/Digital Serial Analyzers — DPO/DSA70000B Series

HDMI Compliance Test Solution (Opt. HT3) – Fast, efficient solution for HDMI
compliance measurement challenges, no matter if you are working on a Source, Cable,
or Sink solution. This application provides all the HDMI compliance test solutions you
need to ensure quality and interoperability.

Power Measurement and Analysis Software (Opt. PWR) –Improvetheefficiency of
switching power supplies with increased power densities. Measure and analyze power
dissipation in power supply switching devices and magnetic components, and generate
detailed test reports in customizable formats.

PCI Expres

PCI-Expre
Option PCE
or RT-Eye.

TekExpress™ SATA Automated Compliance Test Software – Reduce your compliance
test time by approximately 70% with the simple, efficient testing and automation of all
required testing suites provided by TekExpress software. Also included is auto-recognition
of all required test equipment, precise DUT/Host control one-button testing, and complete
support for SATA Gen1 and SATA Gen2 defined test suites.

s Analysis Test Solution (Opt. PCE) – Analyze the performance of your

ss Rev 1.0, 2.0, or 3.0 (draft spec) design with comprehensive test support.

enables tests that conform to PCI-SIG standards using either DPOJET

www.tektronix.com/oscilloscopes 9

Data Sheet

USB 2.0 Compliance Test Solution (Opt. USB) – Ensure your design has sufficient
margins by characterizing your device with variable test limits. The USB compliance
test solution provides “one touch” compliance testing by automatically setting up the
oscilloscope for all compliance test configurations including probe deskew.

Ultra-Wideband Spectral Analysis Software (Opt. UWB) – Analyze hundreds of packet,
TFC, and data-rate combinations without adjusting the UI. In addition, the automatic
WiMedia modulation analysis configuration will analyze how complex wideband signals
change frequency and amplitude with time using real-time spectrograms spanning
20 GHz.

0 Transmitter Testing – Verify, debug, and certify to the specifications of

USB 3.

B 3.0 PHY layer using native capabilities in and additional applications for the

the US

DSA70000B series. Math function FIR filters and SDLA software, allow emulation

DPO/

e Cable and Reference channels defined in the USB 3.0 spec. With DPOJET, jitter

of th

urements needed to complete the Normative compliance test can be done.

meas

10 www.tektronix.com/oscilloscopes

SignalVu™ Vector Signal Analysis – Easily verify wide-bandwidth designs such
as wideband radar, high data rate satellite links, or frequency-hopping radios and
characterize wideband spectral events. SignalVu combines the functionality of a vector
signal analyzer, a spectrum analyzer, and the powerful triggering capabilities of the
DPO/DSA70000B – all in a single package.

Digital Phosphor Oscilloscopes/Digital Serial Analyzers — DPO/DSA70000B Series

DSA70000B – A dedicated solution configured
for today’s high-speed serial design
challenges

The DSA70000B Digital Serial Analyze r is specially configured to address
high-speed serial data designs by encapsulating many of the serial domain
features needed for high-speed serial verification and characterization.
These standar
DPO70000B series.

Serial Pattern Triggering – Real-time serial pattern triggering and protocol

decode with b uilt-in clock recovery recovers the clock signal, identifies the
transitions,
the 8b/10b bit sequences decoded into their words for convenient analysis,
or you can set the desired encoded words for the serial pattern trigger to
capture. With Pattern Lock Triggering, the DSA70000B can synchronize to
long serial test patterns up to 6.25 Gbps and remove random jitter. The
DSA70000B Series covers serial standards up to 3.125 Gbps with an option
to support up

Jitter, Timing, and Eye-diagram Analysis – The DSA70000B Series

features the highest-accuracy jitter and timing measurements as well as
comprehensive analysis algorithms. Tight timing margins demand stable,
low-jitter d
clock cycles on every valid pulse in a single-shot acquisition. Multiple
measurements and trend plots quickly show system timing under variable
conditions, including Random and Deterministic Jitter separation.

Communicat

for verifying compliance to serial communications standards. 156 masks
for the following standards are supported – PCI Express, ITU-T/ANSI
T1.102, Ethernet IEEE 802.3, ANSI X3.263, Sonet/SDH, Fiber Channel,
InfiniBand, USB, Serial ATA, Serial Attached SCSI, IEEE 1394b, RapidIO,
OIF Standards.

20 MSample Record Length – 20 Msamples on all four chan nels provides

a longer time sequence at high resolution. Optional record lengths up to
100 Msamples for the 4, 6, and 8 GHz models, 250 Msamples for the 12.5,
16, and 20 GHz models e xtend the acquisition time sequence.

Advanced Event Search and Mark – Finding important events such as

fast or slow transitions, setup and hold violations, or logic patterns within a
long-duration capture is made easy with the pattern matching and software
triggering functionality of Event Search and Mark.

Accurate, Simple, and Customizable Physical Layer Certification Testing –

For designers with industry-standard certi fication needs, standard-specific
compliance and analysis modules that configure the pass/fail waveform
mask an d measurement limit testing are available as options to the
DSA70000B
and SAS (Opt. SST), FB-DIMM, (Opt. FBD), InfiniBand (Opt. IBA), HDMI
(Opt. HT3), Ethernet (Opt. ET3), DisplayPort (Opt. DSPT), DVI (Opt. DVI),
and USB (Opt. USB).

d features on the DSA70000B Series are options on the

and decodes characters and other protocol data. You can see

to 5 Gbps (Opt. STU)

esigns. You can make jitter measurements over contiguous

ions Mask Testing –

. Modules are available for PCI E xpress (Opt. PCE), Serial ATA

Provides a complete portfolio of masks

ming, and Eye-diagram Analysis

Jitter, Ti

Communications Mask Testing

standard features that extend the functionality of the Tektronix

With
DPO70000B series to address high-speed serial signal analysis and
certification, the DSA70000B series offers a specialized instrument that
efficiently addresses y ou r design challenges.

www.tektronix.com/oscilloscopes 11

Data Sheet

Characteristics

Verti cal S yst

DPO/DSA Models

Bandwidth (user

em

70404B 70604B 70804B 71254B 71604B 72004B

4 GHz 6 GHz 8 GHz 12.5 GHz 16 GHz 20 GHz
selectable DSP
enhance)

Hardware Analog

4 GHz 6 GHz 8 GHz 12.5 GHz 16 GHz (typical) 16 GHz (typical)
Bandwidth (-3 dB)

Input Channels
Rise Time 10% to 90%

444444

98 ps 65 ps 49 ps 32 ps 24.5 ps 19 ps

(typical)
Rise Time 20% to 80%

68 ps 45 ps 34 ps 22 ps 17 ps 14 ps

(typical)
Vertical Noise (% of full

scale) (typical)*

16

Bandwidth Limits

0.28% 0.32% 0.35% 0.38% 0.43% 0.77%

Dependingoninstrumentmodel: 19GHz,18GHz,17GHz,16GHz,15GHz,14GHz,13GHz,12GHz,11GHz,10GHz,

9GHz,8GHz,7GHz,6GHz,5GHz,4GHz,3GHz,2GHz,1GHz,or500MHz

Channel-to-channel
Isolation (Any Two
Channels at Equal
Vertical Scale Settings)

≥120:1 (for input frequency 0 to 10 GHz)
≥80:1 (for input frequency >10 GHz to 12 GHz.
≥50:1 (for input frequency >12 GHz to 15 GHz)

≥25:1 (for input frequency >15 GHz)

DC Gain Accuracy ±2% (of reading)
Delay between any two

channels (typical)
Effective Number of

≤100 ps for any two channels with equal V/div and coupling settings

≤50 ps with BW enhance enabled (BW+)

14

5.4 bits*

Bits (typical)
Input Coupling DC (50 Ω), GND
Input Impedance
Input Sensitivity

18 GHz and below
20 GHz and 19 GHz

Max Input Voltage,
50 Ω

<5.0 V

50 Ω ±2%, 1 MΩ with TCA-1MEG adapter

10 mV/div to 500 mV/div (100 mV to 5 V full scale)

20to500mV/div(200mVto5Vfullscale)

for ≥100 mV/div; also determined by TekConnect accessory

RMS

1.0 V

for <100 mV/div

RMS

Offset Accuracy 10 mV/div – 99.5 mV/div. ±(0.35% (offset value-position) + 1.5 mV + 1% of full scale)

100 mV/div – 500 mV/div. ±(0.35% (offset value-position) + 7.5 mV + 1% of full scale)

Offset Range 10 mV/div: ±450 mV

20 mV/div: ±400 mV
50 mV/div: ±250 mV

100 mV/div: ±2.0 V
200 mV/div: ±1.5 V
500 mV/div: ±0.0 V

Passband Flatness (20,

±0.5 dB to 50% of nominal bandwidth at 25 °C

50, 100, 250 mV/div)
(typical)

Position Range ±5 div
Vertical Resolution

*1450 mV/div, bandwidth filteron,maxbandwidthupto13GHz,maxsamplerate

16

50 mV/div, bandwidth filter on

*

8 bit (11 bit with averaging)

12 www.tektronix.com/oscilloscopes

Digital Phosphor Oscilloscopes/Digital Serial Analyzers — DPO/DSA70000B Series

Time Base System

DPO/DSA Models

Time Base Range
Time Resolution (in

ET/IT mode)
Channel-to-channel

Deskew
Delta Time

Measurement
Accuracy RMS
Over <100 ns duration;
single shot; with signal
rise time = 1.2X scope
rise time

Jitter Noise Floor
(typical)
(With BW+ bandwidth
enhance enabled)

Time Base Accuracy ±1.5 ppm initial accuracy, aging <1 ppm per year
Time Base Delay

Time Range
TriggerJitter(RMS) 1ps

70404B 70604B 70804B 71254B 71604B 72004B

20 ps/div to 1000 s/div 10 ps/div to 1000 s/div

200 fs 100 fs

Range ±75 ns

1.61 ps 1.29 ps 1.14 ps

940 fs 900 fs

450 fs 450 fs 450 fs 300 fs 300 fs 400 fs

-5.0 ks to 1.0 ks

(typical) with enhanced t riggering OFF

RMS

<100 fs

with enhanced triggering ON

RMS

1.02 ps

Acquisition System

DPO/DSA Models 70404B / 70604B / 70804B 71254B / 71604B / 72004B

Sample Rates

Real-time mode 1, 2, 3, or 4 channel (max) 25 GS/s 50 GS/s
ET/IT Mode (max) 5 TS/s 10 TS/s

Maximum Record Length per Channel

With Standard Configuration 10 M on all four channels (DPO70000B Series only)

20 M on all four channels (DSA70000B Series only)
With Record Length Opt. 2XL 20 M on all four channels (DPO70000B Series only)
With Record Length Opt. 5XL 50 M on all four channels
With Record Length Opt. 10XL 100 M on all four channels
With Record Length Opt. 20XL N/A 250 M on all four channels

Maximum Duration at Highest Real-Time Resolution

DPO/DSA Models 70404B / 70604B / 70804B 71254B / 71604B / 72004B

Resolution
Max Duration with Standard Memory 0.4 ms DPO70000B Series; 0.8 ms for

40 ps (25 GS/s) 20 ps (50 GS/s)

0.2 ms DPO70000B Series; 0.4 ms for

DSA70000B Series

DSA70000B Series

Max Duration with Opt. 2XL 0.8 ms (DPO70000B Series only) 0.4 ms (DPO70000B Series only)
Max Duration with Opt. 5XL
Max Duration with Opt. 10XL
Max Duration with Opt. 20XL N/A

2.0 ms 1.0 ms

4.0 ms 2.0 ms

5.0 ms

www.tektronix.com/oscilloscopes 13

Data Sheet

Acquisition Modes

Mode Description

Averaging
Envelope
FastAcq Acquisition Mode
Maximum FastAcq Waveform Capture Rate >300,000 wfms/s on all 4 channels simultaneously
FastFrame™ Acquisition

Hi-Res Real-time boxcar averaging reduces random noise and increases resolution
Peak Detect
Roll Mode
Sample
Waveform Database Accumulate waveform database providing three-dimensional array of amplitude, time, and counts

Pinpoint®Trigg er System

Sensitivity

Internal DC Coup led 4% of full scale from DC to 50 MHz

External (Auxiliary Input) 50 Ω 250 mV from DC to 50 MHz, increasing to 350 mV at 1.0 GHz.

Trigger Characteristics

A Event and Delayed B Event Trigger Types

Main Trigger Modes
Trigger Sequences Main, Delayed by Time, Delayed by Events, Reset by Time, Reset by State, Reset by Transition. All sequences

Clock Recovery System

ock Recovery Phase Locked Loop Bandwidth

Cl

ock Recovery Frequency Range

Cl

8b10b Max Baud Rate

Communications-related Triggers

Serial Pattern Trigger

AUX Trigger
Clock Recovery Jitter (RMS) <0.25% bit period + 2 ps

Enhanced Triggering

Line Fixed at 0 V
Minimum Signal Amplitude needed for Clock Recovery 1 div

Tracking/Acquisition Range ±2% of requested baud
Trigger Coupling DC, AC (attenuates <100 Hz),

Trigger Holdoff Range
Trigger Level Range Internal

From 2 to 10,000 waveforms included in average
From 1 to 2×10

9

waveforms included in min-max envelope

FastAcq optimizes the instrument for analysis of dynamic signals and capture of infrequent events

Acquisition memory divided into segments; maximum trigger rate >310,000 waveforms per second. Time of arrival recorded with
each event. Frame finder tool helps to visually identify transients.

Captures narrow glitches at all real-time sampling rates: 1 ns at ≤125 MS/s; 1/sample rate at ≥250 MS/s
Up to 10 MS/s with a maximum record length of 40 MS
Acquire sampled values

70404B / 70604B / 70804B / 71254B /

DPO Models

71604B / 72004B

70404B / 70604B / 70804B / 71254B /

DSA Models

71604B / 72004B

10% of full scale at 4 GHz
20% of full scale at 8 GHz

50% of full scale at 11 GHz

Edge, Glitch, Runt, Width, Transition Time, Time-out, Pattern, State, Setup/Hold, Window—all except

Edge, Pattern, and State can be Logic State qualified by up to two channels

Auto, Normal, and Single

can include separate horizontal delay after the trigger event to position the acquisition window in time.

Requires Opt. PTH or Opt. MTH Standard

xed at FBaud/1600

Fi

5 MBaud to 3.125 GBaud

1.

Requires Opt. PTU Requires Opt. STU

5GBaud

Requires Opt. MTH Standard

Support for AMI, HDB3, BnZS, CMI, MLT3 and NRZ encoded communications signals. Select among isolated

positive or negative one, zero pulse form or eye patterns as applicable to the standard.

Requires Opt. PTH Stan dard

Up to 64 bit serial word recognizer, bits specified in binary (high, low, don’t care) or hex format.

Trigger on NRZ-encoded data up to 1.25 GBaud.

Trigger on 8b/10b-encoded data from 1.25 to 3.125 GBaud (40 bits)

Requires Opt. PTU Requires Opt. STU

Trigger on 8b/10b-encoded data up to 5 GBaud (40 bits)

TekConnect interface: ±5 V

for PRBS data patterns

<0.25% bit period + 1.5 ps

RMS

for repeating "0011” data pattern

RMS

User-selectable; enhanced triggering corrects the difference in timing between the trigger path and the acquired data

path (supports all Pinpoint trigger types on both A- and B-Events except pattern trigger); Not available in FastAcq.

up to 1.25 Gbaud

p-p

1.5 div

above 1.25 Gbaud

p-p

HF Rej (attenuates >20 kHz),

LF Rej (attenuates <200 kHz),

Noise Reject (reduces sensitivity)

250 ns min to 12 s max

±120% of full scale from center of screen

14 www.tektronix.com/oscilloscopes

Digital Phosphor Oscilloscopes/Digital Serial Analyzers — DPO/DSA70000B Series

Trigger Modes

Mode Description

Comm Standard feature on the DSA70000B, provided as part of Opt.

Edge

Glitch Trigger on or reject glitches of positive, negative, or either

Pattern

Runt

Serial Pattern Trigger on NRZ-encoded data up to 3.125 Gbaud (5 Gbaud

Setup/Hold Trigger on violations of both setup time and hold time

State Any logical pattern of channels (1, 2, 3) clocked by edge on

Time-out

Transition

Trigger Delay by
Events

Trigger Delay by
Time

Width

Window

MTH on the DPO70000B Series. Support for AMI, HDB3,
BnZS, CMI, MLT3 and NRZ encoded signals.

Positive or negative slope on any channel or front panel
auxiliary input. Coupling includes DC, AC, noise reject, HF
reject, and LF reject.

polarity. Minimum glitch width isdownto150ps(typical)with
rearm time of 300 ps

Trigger when pattern goes false or stays true for specified
period of time. Pattern (AND, OR, NAND, NOR) specified for
four input channels defined as high, low, or don’t care.

Trigger on a pulse that crosses one threshold but fails to
cross a second threshold before crossing the first again.
Event can be time- or logic-qualified.

with Opt. PTU or Opt. STU); above 1.25 Gbaud requires
8b/10b encoded data. Extended with pattern lock triggering
to capture repeated acquisitions of long serial test patterns
up to 6.25 Gbps.

between clock and data present on any two input channels.

channel 4. Trigger on rising or falling clock edge.
Trigger on an event which remains high, low, or either, for a

specified time period. Selectable from 300 ps.
Trigger on pulse edge rates that are faster or slower than

specified. Slope may be positive, negative, or either.
1to2Gevents

3.2nsto3Ms

Trigger on width of positive or negative pulse either within or
out of selectable time limits (down to 150 p s).

Trigger on an event that enters or exits a window defined
by two user-adjustable thresholds. E vent can be time- or
logic-qualified.

Search and Mark Events

Event Description

Basic

Advanced

Mark any events and document waveforms. Search positive,
negative slopes or both on any channels. Event table
summarizes all found events. All events are time stamped
in reference to trigger position. Users can choose to stop
acquisitions when an event is found.

Search glitches or runts, as well as transition rate, pulse
width, setup and hold, time-out, window violations, or find any
logic or state pattern on any number of channels. Search
DDR read or write bursts with Opt. DDRA.

Waveform Measurements

Measurement Description

Automatic
Measurements

Amplitude Related Amplitude, High, Low, Maximum, Minimum, Peak-to-Peak,

Combination Area, Cycle Area, Phase, Burst Width
Eye-pattern Related

Histogram Related

Time Related Rise Time, Fall Time, Positive Width, Negative Width,

53, of which 8 can be displayed on screen at any one time;
measurement statistics, user-definable reference levels,
measurement within gates isolating the specific occurrence
within an acquisition to take measurements on.

Mean, Cycle Mean, RMS, Cycle RMS, Positive Overshoot,
Negative Overshoot

Extinction Ratio (absolute, %, dB), Eye Height, Eye Width,
Eye Top, Eye Base, Crossing %, Jitter(p-p,RMS,6sigma),
Noise (p-p, RMS), Signal/Noise Ratio, Cycle Distortion,
Q-Factor

Waveform Count, Hits in Box, Peak Hits, Median, Maximum,
Minimum, Peak-to-Peak, Mean (μ), Standard Deviation
(sigma), μ+1sigma, μ+2sigma, μ+3sigma

Positive Duty Cycle, Negative Duty Cycle, Period, Frequency,
Delay

Waveform Processing/Math

Processing Type Description

Algebraic
Expressions

Arithmetic
Filtering Functions

Frequency Domain
Functions

Mask Function

Math Functions

Relational
Vertical Units

Waveform Definition
Window Functions Rectangular, Hamming, Hanning, Kaiser-Bessel,

Define extensive algebraic expressions including
Waveforms, Scalars, User-adjustable Variables and
Results of Parametric Measurements e.g. (Integral
(CH.1–Mean(CH.1))×1.414×VAR1)

Add, Subtract, Multiply, Divide Waveforms and Scalars
User-definable filters. Users specify a file containing the

coefficients of the filter. Several example filter files are
provided.

Spectral Magnitude and Phase, Real and Imaginary Spectra

unction that generates a Waveform Database pixmap from

Af

ample waveform. Sample count can be defined.

as
Average, Invert, Integrate, Differentiate, Square Root,

Exponential, Log
Cos, Tan, ASin, ACos, ATan, Sinh, Cosh, Tanh

Boolean result of comparison >, <, ≥, ≤,==,!=
Magnitude: Linear, dB, dBm
Phase: Degrees, radians, group delay
IRE and mV units
As an arbitrary math expression

Blackman-Harris, Gaussian, Flattop2, Tek Exponential

, Loge, Abs, Ceiling, Floor, Min, Max, Sin,

10

Display Characteristics

Characteristic

Color Palettes Normal, Green, Gray, Temperature, Spectral, and

Display Format YT, XY
Display Resolution
Display Size Diagonal: 307.3 mm (12.1 in.)
Display Type Liquid crystal active-matrix color display
Horizontal Divisions 10
Vertical Divisions 10
Waveform Styles Vectors, Dots, Variable Persistence, Infinite Persistence

Description

User-defined

XGA 1024 horizontal × 768 vertical pixels

www.tektronix.com/oscilloscopes 15

Data Sheet

Computer System and Peripherals

Item Description

Operating System

Windows XP
CPU Intel Pentium 4, 3.4-GHz processor
PC System Memory 2 GB
Hard Disk Drive

Rear-panel, removable hard disk drive, 160 GB capacity
CD-R/W Drive Front-panel CD-R/W drive with CD creation software

application
DVD Drive Read only
Mouse
Keyboard

Optical wheel mouse, USB interface

USB interface

Input/Output Ports

Front Panel

Port Description

AUX Trigger Input
AUX Trigger Output BNC connector, provides a TTL-compatible,

DC Probe
Calibration Output

Fast Edge Output SMA connector provides fast edge signal. 1 kHz ±20%;

Recovered Clock SMA connector, ≤1.25 Gbps, Output swing ≥130 mV

Recovered Data

USB 2.0 Port One in front. Allows connection of USB keyboard, mouse,

See trigger specifications

polarity-switchable pulse when the oscilloscope

triggers.

BNC connector, ±10 V DC for DC probe calibration. (Signal

available only during probe calibration.)

810 mV (base to top) ±20% into ≥10 kΩ load; 440 mV ±20%

into a 50 Ω load..

50 Ω at 1.25 Gbps. Requires Opt. PTH or Opt. MTH to

p-p

enable on DPO70000B, standard on DSA70000B.

SMA connector, ≤1.25 Gbps, Output swing of 1010 repeating

pattern 200 mV into 50 Ω at 1.25 Gbps. Requires Opt.

PTH or Opt. MTH to enable on DPO70000B, standard on

DSA70000B.

or storage device.

into

Rear Panel

Port Description

Audio Ports

Miniature phone jacks for stereo microphone input and stereo
line output.

AUX Trigger Output BNC connector, 0 to 3 V; default output is A-Event Trigger

low true

External Tim
Reference I

eBase

n

BNC connector; allows time base system to phase lock
to external 10/100 MHz reference. Optimized (by using a
software switch) for either a highly stable clock or tracking
mode.

GPIB Port
Keyboard Port

IEEE 488.2 standard
PS/2 compatible

LAN Port RJ-45 connector, supports 10Base-T, 100Base-T, and

1000Base-T

Mouse Port

PS/2 compatible
Parallel Port IEEE 1284, DB-25 connector
Power

Scope X
Port

GA Video

100to240V

<870 Watts, 400 Hz; CAT II, <1100 VA typical

15 pin D

compat

ing live waveforms on an external monitor or projector.

includ

The pri

nal monitor using this port.

exter

, ±10%, 50/60 Hz; 115 V

RMS

RMS

±10%,

-sub connector on the rear panel, video is IBM XGA

ible. Connects to show the oscilloscope display,

mary Windows desktop can also be displayed on an

Serial Port DB-9 COM1 port
TekLink ™

Synchronizes multiple Tektronix scopes together to a llow

simultaneous acquisition of more than four channels.
Time Base

Reference Out

BNC connector; provides TTL-compatible output of internal

10 MHz reference oscillator
USB 2.0 Ports Four in back. Allow connection of USB keyboard, mouse,

or storage device.
Windows Video Port 15 pin D-sub connector on the rear panel; connects a second

monitor to use dual-monitor display mode allowing analysis

results and plots to be viewed along with the oscilloscope

display. Video is DDC2B compliant.

16 www.tektronix.com/oscilloscopes

Digital Phosphor Oscilloscopes/Digital Serial Analyzers — DPO/DSA70000B Series

Physical Characteristics

Dimensions

Benchtop Configuration

mm

in.

Height 298 11.74
Width 451 17.75
Depth 489.97 19.29

Weight kg lbs.

Net 20 44
Shipping

Rackmount Configuration

34

mm in.

75

Height 311 12.25
Width 480.1 18.9
Depth (from rack mounting

546.1 21.5

ear to back of instrument)

Weight kg lbs.

Net 20 44
Kit 2.7 6

Mechanical

Cooling — Required Clearance

mm

Top 0 0
Bottom 0 0
Left side

76 3
Right side 76 3
Front 0 0
Rear 0 0

in.

Environmental

Temp e r ature

Operating 5 °C to +45 °C
Nonoperating

Humidity

–20°Cto+60°C

Operating 8% to 80% relative humidity (RH) at up to 32 °C. 5% to 45%

RH above +32 °C up to +45 °C

Nonoperating

5% to 95% relative humidity (RH). Upper limit derated to 45%
RH above +30 °C up to +60 °C

Altitude

Operating 10,000 ft. (3,048 m)
Nonopera

Regulatory

Electromagnetic

ting

40,000 ft. (12,190 m)

93/68/EEC; EN61326:1997 +A1 1998+A2:2000

Compatibility
Certifi

cations

-1, CSA1010.1, ISO11469,EN61010-1, IEC 61010-1

UL 3111

Ordering Information

Model Description

DPO70404B 4 GHz Digital Phosphor Oscilloscope
DPO70604B 6 GHz Digital Phosphor Oscilloscope
DPO70804B 8 GHz Digital Phosphor Oscilloscope
DPO71254B 12.5 GHz Digital Phosphor Oscilloscope
DPO71604B 16 GHz Digital Phosphor Oscilloscope
DPO72004B 20 GHz Digital Phosphor Oscilloscope
DSA70404B 4 GHz Digital Serial Analyzer
DSA70604B 6 GHz Digital Serial Analyzer
DSA70804B 8 GHz Digital Serial Analyzer
DSA71254B 12.5 GHz Digital Serial Analyzer
DSA71604B 16 GHz Digital Serial Analyzer
DSA72004B 20 GHz Digital Serial Analyzer

All Models Include: Accessory pouch, front cover, mouse, keyboard, quick start

user manual (071-173x-xx), DPO70000B Series product software CD/DVD-ROM,
Optional applications software CD/DVD-ROM, performance verification procedure
PDF file, GPIB programmer’s reference (on product software CD/DVD-ROM),
calibration certificate documenting NIST traceability, Z 540-1 compliance and
ISO9001, power cord, one year warranty.
Note: Please specify quick-start u ser manual language and power plug when
ordering.
(4) TekConnect
adapter (TCA-BNC)

®

to 2.92 mm adapters (TCA-292MM) and (1) Tekconnect to BNC

www.tektronix.com/oscilloscopes 17

Data Sheet

Options

Instrument Options

Option

Record Length Options for DPO70000B Series

Opt. 2XL 20 MSamples/ch
Opt. 5XL 50 MSamples/ch
Opt. 10XL 100 MSamples/ch
Opt. 20XL*

8

Record Length Options for DSA70000B Series

Opt. 5XL 50 MSamples/ch
Opt. 10XL 100 MSamples/ch
Opt. 20XL*

8

Software Options for DPO70000B Series

Opt. ASM Advanced Event Search and Mark
Opt. MTH Mask testing for Serial Standards up to 4.25 Gbps. Includes

Opt. PTH Protocol Triggering and Decoding for 8b/10b-encoded Serial

Opt. PTU Protocol Triggering and Decoding for 8b/10b-encoded Serial

ware Options for DSA70000B Series

Soft

Opt. STU Protocol Triggering and Decoding for 8b/10b-encoded Serial

Software Options for DPO70000B Series and DSA70000B Series

Opt. DDRA*
Opt. DJA DPOJET Jitter and Eye Diagram Analysis
Opt. DSPT*

11

Opt. DVI DVI Compliance Test Solution
Opt. ET3*
Opt. FBD*

2

5

Opt. HT3 HDMI Compliance Test Software
Opt. IBA*

5

Opt. LT Waveform Limit Testing
Opt. PCE*
Opt. PWR*

15

4

Opt. RTE Serial Data Compliance and Analysis Software
Opt. SLA Serial Data Link Analysis Advanced (with Equalization)
Opt. SLE Serial Data Link Analysis Essentials (no Equalization)
Opt. SST*

5

Opt. SVE SignalVu™ Essentials – Vector Signal Analysis Software
Opt. SVM*
Opt. SVP*

Opt. USB*

10

10

3

Opt UWB Ultra-Wideband Spectral Analysis (includes WiMedia Alliance

Description

250 MSamples/ch

250 MSamples/ch

hardware clock recovery.

Signals up to 3.125 Gbps. Includes hardware clock recovery
and pattern lock triggering.

Signals up to 5 Gbps.

Signals up to 5 Gbps.

9

DDR Memory Bus Analysis

DisplayPort Compliance Test Solution

Ethernet Compliance Test Software
FB-DIMM Compliance Module for RT-Eye Ser ial Data

Compliance and Analysis Software

InfiniBand Compliance Module for RT-Eye Serial Data
Compliance and Analysis Software

PCI Express™ Analysis Software
Power Measurement and Analysis Software

SATA and SAS Analysis Software Module for RT-Eye Serial
Data Compliance and Analysis Software

General Purpose Modulation Analysis. Requires option SVE
Advanced Signal Analysis (including pulse measurements).

Requires option SVE
USB 2.0 Compliance Test Software only

PHY interf. testing)

Option

Description

Opt UWBE Ultra-Wideband Spectral Analysis Essentials

*2Requires Ethernet Test Fixture.

3

Requires TDSUSBF (USB Test Fixture).

*

4

At least Opt. 2XL and a TCA-1MEG TekConnect 1 MΩ buffer amplifier are recommended for use.

*

5

Requires Opt. RTE on DPO70000B Series.

*

8

For models of bandwidth ≥ 12.5 GHz only.

*

9

Requires DJA and ASM.

*

10

Requires Opt. SVE, SVEH, or SVEU.

*

11

For models of bandwidth ≥ 8GHzonly.

*

15

Requires Opt. RTE or Opt. DJA on DPO70000B Series

*

User Manual Options

Option

Opt. L0
Opt. L1

Description

English

French
Opt. L3 German
Opt. L5

Japanese
Opt. L7 Simple Chinese
Opt. L8 Standard Chinese
Opt. L9
Opt. L10
Opt. L99

Korean

Russian

No manual

Power Plug Options

Option

Opt. A0
Opt. A1
Opt. A2
Opt. A3

Description

North America

Universal European Union

UK

Australia
Opt. A5 Switzerland
Opt. A6

Japan
Opt. A10 China
Opt. A11
Opt. A99

India

No power cord

Service Options

Option

Description

Opt. CA1 Provides a single calibration event or coverage for the

designated calibration interval, whichever comes first
Opt. C3 Calibration Service 3 Years
Opt. C5 Calibration Service 5 Years
Opt. D1 Calibration Data Report
Opt. D3 Calibration Data Report 3 Years (with Opt. C3)
Opt. D5 Calibration Data Report 5 Years (with Opt. C5)
Opt. R3 Repair Service 3 Years
Opt. R5 Repair Service 5 Years

18 www.tektronix.com/oscilloscopes

Digital Phosphor Oscilloscopes/Digital Serial Analyzers — DPO/DSA70000B Series

Recommended Accessories

Probes

Probe Description

P7520
P7516
P7513A
P7313SMA 13 GHz TekConnect®differential SMA probe
P7508
P7380SMA 8 GHz TekConnect®differential SMA probe
P7506
P7504
P6251

P6250

TCPA300/TCPA400 Series current measurement systems
P5200/P5205/P5210 High-voltage differential probes

Adapter

Adapter Description

TCA-1MEG TekConnect high-impedance buffer amplifier. Includes

TCA-292MM TekConnect to 2.92 mm connectors
TCA-BNC TekConnect-to-BNC adapter
TCA-N TekConnect-to-N adapter
TCA-SMA TekConnect-to-SMA adapter
TCA75 8 GHz precision TekConnect 75 Ω to 50 Ω adapter with 75 Ω

s

20 GHz TriMode™ probe
16 GHz TriMode™ probe
13 GHz TriMode™ probe

8 GHz TriMode™ probe

6 GHz TriMode™ probe
4 GHz TriMode™ probe
DC to 1 GHz, 42V, Differential Probe (requires TCA-BNC

adapter)
DC to 500 MHz, 42V, Differential Probe (requires TCA-BNC

adapter)

P6139A passive probe

BNC input connector

Cables

Cable Order

Centronics Cable
GPIBCable(1m)
GPIBCable(2m)
RS-232 Cable

012-1214-00

012-0991-01

012-0991-00

012-1298-00

Accessories

Accessory

Ethernet Test
Fixture

Instrumented DIMM
for DDR3

Oscilloscope Cart
Probe Calibration

and Deskew Fixture
(4 GHz)

Probe Deskew
Fixture (>4 GHz)

Power Deskew
Fixture

Rackmount Kit 016-1985-00
Service Manual
TDSUSBF Test fixtureforusewithOpt. USB
Transit Case

Order

Order through Crescent Heart Software

(http://www.c-h-s.com)

Order Scope NEXVu card for UDIMM Raw Card E. (Contact

http://www.nexustechnology.com)

K4000

067-0484-xx

067-1586-xx

067-1686-xx

071-1740-xx

016-1977-00

www.tektronix.com/oscilloscopes 19

Data Sheet

Instrument Up grades

To upgrade your DPO70000B Series Oscilloscope or your DSA70000B Series
Serial Analyzer, order DPO7UP and option as noted.

Option Description

To upgrade re

XL02
XL25
XL210
XL220*

cord length on DPO70000B Series from:

Standard configuration to Opt. 2XL configuration
Opt. 2XL configuration to Opt. 5XL configuration
Opt. 2XL configuration to Opt. 10XL configuration

8

Opt. 2XL configuration to Opt. 20XL configuration (only
available on instruments of bandwidth >= 12.5 GHz)

To upgrad

XL05
XL010
XL020*

erecordlengthfromstandardconfiguration to:

Opt. 5XL configuration
Opt. 10XL configuration

8

Opt. 20XL configuration (only available on instruments of
bandwidth >= 12.5 GHz)

ade record length on DPO70000B Series or DSA70000B

To upgr

Series from:

XL510
XL520*

8

Opt. 5XL configuration to Opt. 10XL configuration
Opt. 5XL configuration to Opt. 20XL configuration (only

available on instruments of bandwidth >= 12.5 GHz)

8

XL1020*

Opt. 10XL configuration to Opt. 20XL configuration (only
available on instruments of bandwidth >= 12.5 GHz)

To upgrade bandwidth on DPO70000B Series or DSA70000B Series

from:

BWU4T6
BWU4T8
BWU4T12
BWU4T16
BWU4T20
BWU6T8
BWU6T12
BWU6T16
BWU6T20
BWU8T12
BWU8T16
BWU8T20
BWU12T16
BWU12T20
BWU16T20

4GHzto6GHzconfiguration
4GHzto8GHzconfiguration
4GHzto12.5GHzconfiguration
4GHzto16GHzconfiguration
4GHzto20GHzconfiguration
6GHzto8GHzconfiguration
6GHzto12.5GHzconfiguration
6GHzto16GHzconfiguration
6GHzto20GHzconfiguration
8GHzto12.5GHzconfiguration
8GHzto16GHzconfiguration
8GHzto20GHzconfiguration

12.5 GHz to 16 GHz configuration

12.5 GHz to 20 GHz configuration
16GHzto20GHzconfiguration

To up grad e:

ASM DPO70000B with Opt. ASM
MTH
PTH
DJAH
DJAU

DPO70000B with Opt. MTH
DPO70000B with Opt. PTH
DPO70404B, 70604B, 70804B with Opt. DJA
DPO71254B, 71604B, 72004B with Opt. DJA

To upgrade DPO

6

CP2*

70000B Series or DSA70000B Series with:

TDSCPM2 ANSI/ITU Telecom pulse co mpliance testing

software (requires Opt. MTH on DPO70000B Series)

9

DDRA*
DVI

13

EQ*
ET3
FBD*
HT3

5

IBA*
J2
LT
PCE*
PWR

5

15

Opt. DDRA

Opt. DVI

From Opt SLE to Opt. SLA

Opt. ET3

Opt. FBD

Opt. HT3

Opt. IBA

TDSDDM2 disk-drive analysis software

Opt. LT

Opt. PCE

Opt. PWR
SLA Opt. SLA
SLE Opt. SLE

5

SST*
SVEH*
SVEU*
SVM*
SVP*

11

12

10

10

Opt. SST

Opt. SVE

Opt. SVE

Opt. SVM

Opt. SVP
USB Opt. USB
UWB
UWBE
VNM*

7

Opt. UWB

Opt. UWBE

TDSVNM CAN and LIN Timing and Protocol Decode (no

CAN triggering included)

*5Requires Opt. RTE on DPO70000B Series.

6

Requires Opt. MTH on DPO70000B Series

*

7

*

Requires ATM1 CAN/LIN trigger module - Order through Crescent Heart Software

8

For models of bandwidth ≥ 12.5 GHz only

*

9

Requires DJA and ASM

*

10

*

Requires Opt. SVE, SVEH, or SVEU

11

DPO/DSA70404B, DPO/DSA70604B, DPO/DSA70804B only

*

12

DPO/DSA71254B, DPO/DSA71604B, DPO/DSA72004B only

*

13

*

Request Opt. SLE

15

Requires Opt. RTE or Opt. DJA on DPO70000B Series

*

Product(s) are manufactured in ISO registered facilities.

20 www.tektronix.com/oscilloscopes

Digital Phosphor Oscilloscopes/Digital Serial Analyzers — DPO/DSA70000B Series

www.tektronix.com/oscilloscopes 21

Data Sheet

Contact Tektronix:

ASEAN / Australa

Balkans, Israel, South Africa and other ISE Countries [phone]

Central East Eu

Mexico, Central/South America & Caribbean 52 (55) 54247900

rope, Ukraine, and the Baltics [phone]

Central Europe & Greece [phone]

Luxembourg [phone]

Middle Eas t,

For other areas contact Tektronix, Inc at: 1 [phone]

Asia, and North Africa [phone]

The N etherlands 090 02 021797

People’s Rep

United Kingdom & Ireland [phone]

ublic of China 86 (10) 6235 1230

Republic of

sia (65) 6356 3900

Austria [phone]

Belgium 07 81 601

Brazil [phone]

Canada 1 [phone]

Denmark [phone]

Finland +41526

France [phone]

Germany [phone]

Hong Kong (852

India (91) 80-42922600

Italy [phone]

Japan 81 (3) 67

Poland [phone]

Portugal 80 08 12370

Korea 82 (2) 6917-5000

Russia & CIS [phone]

South Africa [phone]

Spain (+3 4)

Sweden 020 08 80371

Switzerland [phone]

Tai wa n 886 (

USA 1 [phone]

75 3777

) 2585-6688

14-3010

Norway 800 16098

901 988 05 4

2) 2722-9622

Updated 30 October 2008

66

www.tektronix.com/oscilloscopes

For Further Information. Tektronix maintains a comprehensive, constantly expanding
collection of application notes, technical briefs and other resources to help engineers working
on the cutting edge of technology. Please visit www.tektronix.com

t © Tektronix, Inc. All rights r eserved. Tektronix products are covered by U.S. and foreign patents,

Copyrigh

d pending. Information in this publication supersedes that in all previously published material.

issued an

tion and price change privileges reserved. TEKTRONIX and TEK are registered trademarks of

Specifica

x, Inc. All other trade names referenced are the service marks, trademarks, or registered trademarks

Tek tro ni

espective companies.

of their r

29 Jan 2009 55W-23032-1