Tektronix DPO7254 Data sheet

Digital Phosphor Oscilloscopes
DPO7000C Series Data Sheet
Connectivity
Features & Benets
Key Performance Specifications
3.5 GHz, 2.5 GHz, 1 GHz, and 500 MHz Bandwidth Models
Up to 40 GS/s Real-time Sample Rate on One Channel, up to 20 GS/s on Two Channels, and up to 10 GS/s on Three or Four Channels
Up to 500 Megapoint Record L ength with MultiView Zoom™
FastFrame™ Segmented Memory Acquisition Mode with >310,000 Waveforms per Second Cap ture Rate
electable Bandwidth Limit Filters for Better Low-f reque ncy
User-s Measurement Accuracy
Ease-of-Use Features
Pinpoint®Triggering provides the Most Flexible and Highest Performance Triggering, with over 1400 Combinations to Address
lly Any Triggering Situation
Virtua
Visual Trigger Precisely Qualies Triggers and Finds Unique Events in Complex Waveforms
Advanced Search and Mark to Find SpecicEventsintheEntire Waveform
Optional Serial Triggering and Analysis
Optional Technology Specic Analysis
MyScope®Custom Control Windows and Right Mouse Click Menus for Exceptional Efciency
53 Automated Measurements, Waveform Histograms, and FFT Analysis for Simplied Waveform Analysis
TekV P I®Probe Interface supports Active, Differential, and Current Probes for Automatic Scaling and Un its
12.1 in. (307 mm) Bright XGA Display with Touch Screen
USB Host Ports on the Front and Side Panels for Quick and Easy Data Storage, Printing, and Connecting USB Peripherals
Integrated 10/100/1000BASE-T Eth ernet Port for Network Connection and Video Out Port to Export the Oscilloscope Display to a Monitor or Projector
Microsoft®Windows 7 64-bit Operating System for Easy Connectivity and Integration into Your Environment
LXI Class C Compliant
Automated Serial Triggering and Decode Options for I2C, SPI, RS-232/422/485/UART, and USB 2.0
Automated Serial Analysis for MIPI®D-PHY DSI-1 and CSI -2
Automated Serial Decode and Vehicle Network Monitoring of CAN and LIN
Clock Recovery from S erial Data Streams
64-bit NRZ Serial Pattern Trigger for Isolation of Pattern-dependent Effectsupto1.25Gb/s
Software Solutions provide Built-in Domain Expertise for MIPI D-PHY, Ethernet, and USB 2.0 Compliance Testing, Jitter, Timing, Eye Diagrams, Power, DDR Memory Bus Analysis, and Wideband RF
Limit and Mask Testing provide Quick Insight into Signal Characteristics
®
Data Sheet
Simplied Analysis for Complex Digital Designs
With the DPO7000C Digital Phosphor Oscilloscope Series, you can analyze analog and serial bus signals with a single instrument to quickly nd and diagnose problems in complex designs. Bandwidths up to 3.5 GHz and sample rates u see fast-changing signal details. To capture long windows of signal activity while maintaining ne timing resolution, the DPO7000C Se ries o ffers a dee p record length of up to 12.5M points standard on all channels and an optional record length of up to 500M points on one channel.
With Advanced Search and Mark and MultiView Zoom™ features for rapid waveform navigation, and more than 15 optional software and analysis packages for common technologies and in-depth analysis tasks, the DPO7000C Ser to simplify and speed debug of your complex design.
p to 40 GS/s ensure you have the performance you need to
ies from Tektronix provides the feature-rich tools you need
Comprehensive Features Speed Every Stage of Debug
The DPO7000C Series offers a robust set of features to speed every stage of debugging your design – from quickly discovering an anomaly and capturing it, to searching your waveform record for the event and analyzing its characteristics and your device's behavior.
Discover
To debug a design problem, rst you must know it exists. Every design engineer spends time looking for problems in their design, a time-consuming and frustrating task without the right debug tools.
Discover – of capturi
The DPO7000C Series offers the industry's most complete visualization of signals, providing fast insight into the real operation of your device. Tektronix proprietary FastAcq™ technology delivers a fast waveform capture – greater than 250,000 waveforms per second – th at enables you to see glit true nature of device faults. A digital phosphor display with color intensity grading shows the history of a signal's activity by using color to identify areas of the signal that occur more frequently, providing a visual display of just how often anomalies occur.
Fast waveform capture rate - over 250,000 wfm/s - maximizes the probability
ng elusive glitches and other infrequent events.
ches and other infrequent transients within s econds, revealing the
2 www.tektronix.com
Digital Phosphor Oscilloscopes — DPO7000C Series
Capture–T complete s quickly ca
riggering on a specic transmit data packet going across an RS-232 bus. A
et of triggers, including triggers for specic serial packet content, ensures you
pture your event of interest.
Capture
Discovering a device fault is only the rst step. Next, you must capture the event of interest to identify root cause.
The DPO7000C Series provides a complete set of triggers – inc luding runt, glitch, width, timeout, transition, pattern, state, setup/hold violation, window, comm, and serial pattern – to help quickly nd your event. Enhanced Triggering reduces trigger jitter at the trigger point. In this mode, the trigger point can be used as a measurement reference.
To enable complex system debug and validation, the DPO7000C Series
®
provides Pinpoint
de trigger performance up to the bandwidth of th e oscilloscope and
to provi
triggering, using Silicon Germanium (SiGe) technology
over 1400 trigger combinations. Most other trigger systems offer multiple trigger types only on a single event (A event), with the delayed trigger (B event) selection limited to edge-type triggering, and often do not provide a way to reset the trigger sequence if the B event doesn’t occur. But Pinpoint triggering provides a full suite of advanced trigger types on both A and B
s with Reset triggering to begin the trigger sequence again after a
trigger specied time, state, or transition so that even events in the most complex signals can be captured.
Finding the right characteristic of a complex signal can require hours of collecting and sorting through thousands of acquisitions for the event of interest. Dening a trigger that isolates the desired event and shows data only when the event occurs speeds up this process. The optional Visual Trigger makes the identication of the desired waveform events quick and
scanning through all waveform acquisitions and comparing them to
easy by on-screen areas (geometric shapes).
to a 500M point record length, you can capture many events of
With up interest, even thousands of serial packets, in a single acquisition for further
Search – Results of an advanced search for a runt pulse or a narrow glitch within a long waveform record. Each instance of the runt or glitch is automatically marked for easy reference.
analysis while maintaining high resolution to zoom in on ne signal details. Investigate multiple segments of your waveform capture simultaneously with MultiView Zoom™ to quickly compare events in real time. FastFrame™ Segmented Memory mode enab les you to make efcient use of large records by capturing many trigger events in a single record eliminating large time gaps between events of interest. View and measure the segments individually or as an overlay.
From triggering on specic packet content to automatic de co de in multiple data formats, the DPO7000C Series pro vid es integrated support for a broad range of serial buses – I
2
C, SPI, RS-232/422/485/UART, USB 2.0, CAN, LIN, and MIPI D-PHY. The ability to decode up to 16 serial buses simultaneously means you gain insight into system-level problems quickly.
Search
Finding your event of interest in a long waveform record c an be time consuming without the right search tools. With today's record lengths pushing beyond a million data points, locating your event can mean scrolling through thousands of screens of signal activity.
The DPO7000C Series offers the industry's most comprehensive search and waveform navigation with the standard Advanced S earch and Mark
and front-panel controls. User marks allow you to mark any
feature location that you m ay want to reference later for further investigation. Or, automatically search your entire record for the criteria yo u dene. Along the way it will aut omatically mark every occurren ce of your dened event so you can quickly move between events. The advanced search and mark capability of th e DPO7000C Series can search for up to eight different
imultaneously and stop a live acquisition when it nds an event
events s of interest, saving even more time.
www.tektronix.com 3
Data Sheet
Analyze – Waveform histogram of a falling edge showing the distribution of edge position (jitter) over time. Included are numeric measurements made on the waveform histogram data. A comprehensive set of integrated analysis tools speeds verication of your design's performance.
Analyze
Verifying that your prototype's performance matches simulations and meets the project's design goals requires a nalyzing its behavior. Tasks can range from simple checks of rise times and pulse widths to sophisticated power loss analysis, characterization o f system clocks, and investigation of noise sources. The DPO7000C Series offers a comprehensive set of integrated analysis tools including waveform- and screen-based cursors, 53 automated measurements, a dvanced waveform math including arbitrary equation editing, waveform histograms, and FFT a nalysis.
Every DPO7000C Series oscilloscope includes the DPOJET Essentials jitter and eye pattern analysis software package, extending the oscilloscope's measurement capabilities to make measurements over contiguous clock and data cycles in a single-shot real-time acquisition. This enables measurement of key jitter and timing analysis parameters s uch as Time Interval Error and Phase Noise to help characterize possible system timing issues. Analysis tools such as plots for time trends and histograms quickly show how timing parameters change over time, and spectrum analysis quickly shows the precise frequency and amplitude of jitter and modulation sources.
Specialized application support fo r serial bus debug and compliance test, jitter and eye pattern analysis, power sup ply design, limit and mask testing, DDR memory bus analysis, and wideband RF is also available.
Advanced Search and Mark
A 12.5M point standard record length represents thousands of screens of information. The DPO7000C Series enables you to nd your event in seconds with Advanced Search and Mark.
Search ste
Search step 2: Advanced Search and Mark automatically searches through the record and marks each event with a solid colored triangle. You can then use the Previous and Next buttons to jump from one event to the next.
User M
p 1: You dene what you would like to nd.
arks
Press the Set/Clear front-panel button to place one or more marks on
veform. Navigatingbetweenmarksisassimpleaspressingthe
the wa Previous ()andNext () buttons on the front panel.
Search Marks
earch button allows you to automatically search through your long
The S acquisition looking for user-dened events. All occurrences of the event are highlighted with search marks and are easily navigated to, using the front-panel Previous () and Next () buttons. Search types include edge, glitch, width, timeout, runt, pattern, state, setup and hold, transition, and window.
4 www.tektronix.com
Digital Phosphor Oscilloscopes — DPO7000C Series
osphor technology enables greater than 250,000 wfm/s waveform capture rate
Digital ph
ime color grading on the DPO7000C Series.
and real-t
Digital Phosphor Technology
The DPO7000C Series' digital ph osphor technology provides you with fast insight into the real operation of your device. Its fast waveform capture rate – greater than 250,000 wfm/s – gives you a high probability of quickly seeing the infrequent problems common in digital systems: runt pulses, glitches, timing issues, and more.
Waveforms are superimposed with one another and waveform points are color coded by frequency of occurrence. This quickly highlights the events
ur more often over time or, in the case of infrequent anomalies,
that occ occur less often.
With the
DPO7000C Series, you can choose innite p ersistence or variable persistence, determining how long the previous waveform acquisitions stay on-screen. This allows you to determine how often an anomaly is occurring.
Visual Trigger (Optional)
The Visual Trigger option adds an additional dimension to the standard trigger system that provides a n intuitive method of triggering based on shapes in the oscilloscope’s graticule. It enables the user to dene shapes
scilloscope’s display that qualify trigger events for the incom ing
on the o signals. Areas can be created using a variety of shapes including triangles, rectangles, hexagons, or trapezoids to t the area to the particular trigger behavior desired. Once shapes are created on the oscilloscope’s display, they can be positioned and/or re-sized dynamically while the oscilloscope is in Run mode to create ideal trigger conditions. Visual Trigger can be
ed with the standard triggers and act as a Boolean logic qualier
combin for the “A” and “B” events.
Serial Triggering and Analysis (Optional)
On a serial bus, a single signal often includes address, control, data, and clock information. This can make isolating events of interest difcult. The DPO7000C Series offers a robust set of tools for debugging serial buses
Eye Diagram triggering using optional Visual Trigger.
Triggering on a specic OUT Token packet on a USB full-speed serial bus. A bus waveform provides decoded packet content including Start, Sync, PID, Address, End Point, CRC, Data values, and Stop.
with automat
ic trigger and decode on I
2
C, SPI, RS-232/422/485/UART, CAN, LIN, and USB 2.0, and decode for MIPI D-PHY DSI-1 and CSI-2 serial buses.
Serial Triggering
Trigger on packet content such as start of packet, specicaddresses, specic data content, unique identiers, etc. on popular serial interfaces such as I
2
C, SPI, RS-232/422/485/UART, CAN, and USB 2.0.
Bus Display
Provides a higher-level, combined view of the individual signals (clock, data, chip enable, etc.) that make up your bus, making it easy to identify where packets begin and end and identifying subpa cket components such as address, data, identier, CRC, etc.
www.tektronix.com 5
Data Sheet
e showing decoded serial packet data in a long acquisition.
Event tabl
Bus Decoding
Tired of having to visually inspect the waveform to count clocks, determine if each bit is a 1 or a 0, combine bits into bytes, and determine the hex value? Let the oscilloscope do it for you! Once you've set up a bus, the DPO7000C Series will decode each packet on the bus, and display the value in hex, binary, decimal (USB only) or ASCII (USB and RS-232/422/485/UART only) in the bus
Event Tab
In addition to seeing decoded packet data on th e bus waveform itself, you can view a a software listing. Packets are time stamped and listed consecutively with columns for each component (Address, Data, etc.).
Bus Searching
Serial triggering is very useful for isolating the event of interest, but once you’ve captured it and need to a nalyze the surrounding data, what do
waveform.
le Display
ll captured packets in a tabular view much like you would see in
CAN and LIN Timing and Protocol Decode.
you do? In the past, users had to manually scroll through the waveform counting and converting bits and looking for what caused the event. With the DPO7000C Series, you can have the oscilloscope automatically search through the acquired data for user-dened criteria including serial packet content. Each occurrence is highlighted by a search mark. Rapid navigation between marks is as simple as pressing the Previous ()andNext () buttons on the front panel.
CAN and LIN Timing and Protocol Decode Software (Optional)
The optional CAN/LIN serial analysis software package (Option LSA) enables you to ensure seamless and reliable operation of a CAN or LIN
. The software measures oscillator tolerance and pro pagation delay
network on CAN buses, provides CAN triggering, and simultaneously decodes CAN and LIN messages.
6 www.tektronix.com
Digital Phosphor Oscilloscopes — DPO7000C Series
USB 2.0 Com
pliance Testing.
Serial Bus Compliance Test (Optional)
Software packages for automated com pliance test are available for MIPI D-PHY (Option D-PHY), Ethernet 10BASE-T, 100BASE-TX, and 1000BASE-T (Option ET3), and USB 2.0 (Option USB) physical-layer devices. These software packages enable you to conduct testing using the standard's specied compliance tests.
Power Analysis (Optional)
The optional power analysis software package (Option PWR) e nables quick and accurate analysis of power quality, switching loss, harmonics, magnetic measurements, safe operating area (SOA), modulation, ripple, and slew rate (di/dt, dv/dt). Automated, repeatable power measurements
able with a touch of a button; no external PC or complex software
are avail setup is required. The package includes a report generation tool to create customizable, detailed reports to document your measurement re sults.
Advance Diagram
The optional DPOJET Advanced software package (Option DJA) offers extende insight into jitter and timing as well as other signal quality issues. DPOJET Advanced adds advanced tools such as Rj/Dj separation, eye diagram masks, and Pass/Fail limits for conformance testing. The innovative
d Analysis, Jitter, Timing, and Eye Measurements (Optional)
d capabilities, providing a complete suite of analysis tools for
Switching Loss measurements. Automated power measurements enable quick and accurate analysis of common power parameters.
Advanced Analysis, Jitter, Eye Diagram, and Timing measurements.
one-touc Advanced is also a measurement frame work that works in conjunction with standards-specic compliance test packages for a pplications such as DDR memory and USB.
h wizard makes setup for jitter measurements easy. DPOJET
www.tektronix.com 7
Data Sheet
ng an OC-12 signal, capturing any violations of the mask.
Mask testi
Limit and Mask Testing (Optional)
The optional limit test (Option LT) and mask te st (Option MTM) software packages are useful for long-term signal monitoring, characterizing signals during design, and testing on a pro duction line. The limit test software
compares a tested signal to a known good or "golden" version of the same signal with user-dened vertical and horizontal tolerances. The mask test softw and computer standards for easily checking compliance to a standard. Additionally, custom masks can be created and used for characterizing signals. With both software packages you can tailor a test to your specific requirements by dening test duration in a number of wavefo rms, setting a violation threshold that must be met before considering a test a failure, counting hits violations, test failure, a nd test complete. Whether specifying a limit template or a mask, conducting pass/fail tests in search of waveform anomalies such as glitches has never been e asier.
are includes a robust set of masks for telecommunications
along with statistical information, and setting actions upon
DDR M emory Bus Analysis (Optional)
The optional DDR memory analysis software package (Option DDRA) automatically identies DDR1, DDR2, DDR3, LP-DDR, LP-DDR2, and GDDR3 Reads a with Pass/Fail results on all edges in e ve ry Read and Write burst, perfect for debugging and troubleshooting DDR memory buses. Also provided are common measurements of clock, address, and control signals. Used in conjunction with DPOJET (Option DJA), Option DDRA is the fastest way to debug complex memory signaling issues.
nd Writes and makes JEDEC conformance measurements
8 www.tektronix.com
Digital Phosphor Oscilloscopes — DPO7000C Series
SignalVu™ enables detailed analysis in multiple domains.
Vector Signal Analysis (Optional)
The optional SignalVu™ vector signal analysis packages (Options SVE, SVM, SVO, SVP, and SVT) easily validate wideband designs and characte engine of Tektronix real-time spectrum analyzers with the wide bandwidth acquisition of Tektronix digital oscilloscopes, you can now evaluate complex baseband signals directly on your oscilloscope. You get the functionality of a vector signal analyzer, a spectrum analyzer, and the powerful trigger capabilities of a digital oscilloscope – all in a single package. Whether your desi satellite links, or frequency-hopping communications, Sig nalVu™ v ector signal analysis software can speed your time-to-insight by showing you time-variant behavior of these wideband signals.
rize wideband spectral events. By combining the signal analysis
gn validation needs include wideband radar, high data-rate
Designed to Make Your Work Easier
Large, High-resolution Display
The DPO7 an integrated touch screen for seeing intricate signal details.
000C Series features a 12.1 in. (307 mm) XGA color display with
TekVPI prob
e interface simplies connecting your probes to the oscilloscope.
Connectivity
USB 2.0 host ports on th e front and side panels enable easy transfer of screenshots, instrument settings, and waveform data to a USB thumb drive. The rear panel contains a GPIB port for controlling the oscilloscope remotely from a computer. An integrated 10/100/1000BASE-T Ethernet port enables easy connection to networks and a Video Out port allows the
cope display to be exported to an external monitor or projector.
oscillos PS-2 ports for keyboard and mouse are included for security-conscious applications that require the U SB ports to be disabled. A standard removable hard disk drive makes customizing settings for different users easy as well as enables use in secure environments.
TekVPI®Probe Interface
The TekVPI probe interface sets the sta ndard for ease of use in probing . TekVPI probes feature status indicators and controls, as well a s a probe menu button right on the probe itself. This button brings up a probe menu on the oscilloscope display with all relevant settings and controls for the probe. The TekVPI interface enables direct attachment of a current probe
requiring a separate power supply. TekVPI probes can be controlled
without remotely through USB, GPIB, or Ethernet, enabling mo re versatile solutions in ATE environments.
Dedicated Front-panel Controls
annel vertical controls provide simple and intuitive operation. No
Per-ch longer do you need to share one set of vertical controls across all four channels.
www.tektronix.com 9
Data Sheet
MyScope cu enabling e
MyScope®Custom Control Window
Easily create your own personalized "toolbox" of oscilloscope features in a matter of minutes using a simple, visual, drag-and-drop process. Once created, these custom control windows are easily accessed throu gh a dedicated MyScope menu selection on the oscilloscope. This is ideal in a shared resource environment where each person can have their own custom co windows benet all oscilloscope users, eliminating the ramp-up time that many face when returning to the lab after not using an oscilloscope for a while, and enabling power users to be far more efcient.
Floating Licenses
Floating licenses offer an alternative method to manage your Tektronix asset. Floating licenses allow license-key enabled options to be easily moved among all your MSO/DPO5000, DPO7000, and DPO/DSA/MSO70000 Series of Tektronix oscilloscopes. Floating licenses are avai version of an option license add “DPOFL-“ prex to the option name. (e.g. DPOFL-ET3)
stom control windows are created with a simple drag-and-drop process
ach user to have a unique interface.
ntrol interface suited to their particular use. MyScope control
lable for many license-key enabled options. To order a oating
Check www.tektronix.com for additional information about oating license options.
Interoperability with Logic Analyzer for Digital Design and Debug
The Tektronix Integrated View (iView™) data display enables digital designers to solve signal integrity challenges and effectively debug and verify their systems more quickly and easily. This integration allows designers to view time-correlated digital and analog data in the same display windows, and isolate the analog characteristics of the digital signals that are causing system failures. No user calibration is required. And, once set up, the iView feature is completely automated.
Remote Operation and Extended Analysis
There are many ways to connect to your DPO7000C Series oscilloscope to conduct extended analysis. The rst makes use of the Windows Remote Desktop c
apability – connect directly to your oscilloscope and operate the user interface remotely through the built-in Remote Desktop. A second way to connect is through Tektronix OpenChoice
®
software which makes use of the fast embedded bus, transferring waveform data directly from acquisition to analysis applications on the Windows desktop at much faster speeds than conventional GPIB transfers. Industry-standard protoco ls, such as TekVIS
A™ interface and ActiveX controls are included for using and enhancing Windows applications for data analysis and documentation. IVI-COM instrument drivers are included to enable easy com munication with the oscilloscope using GPIB, serial data, and LAN connections from programs running on the instrument or an external PC. Or, use the Software Developer's Kit (SDK) to help cre ate custom software to automate
ep processes in w aveform collection and ana lysis with Visual
multist BASIC, C, C++, MATLAB, LabVIEW, LabWindows/CVI, and other common Application Development Environments (ADE). Microsoft
®
Excel and Word toolbars are included to simplify data capture and transfer directly to these programs running on the Windows desktop. A third way to connect to your oscilloscope is through NI LabVIEW SignalExpress Tektronix Edition,
g you to instantly acquire, generate, analyze, compare, import , and
enablin save measurement data and signals using an intuitive drag-an d-dro p user interface that does not require any programming.
10 www.tektronix.com
Characteristics
Digital Phosphor Oscilloscopes — DPO7000C Series
Verti cal S yst
Characteristic DPO7054C DPO7104C DPO7254C DPO7354C
Input Channels Bandwidth 500 MHz Rise Time 10% to 90% (Typical) Rise Time 20% to 80% (Typical) DC Gain Accuracy ±1% with offset/position set to 0 Bandwidth Limits Input Coupling AC, DC, GND Input Impedance Input Sensitivity 1 M: 1 mV/div to 10 V/di v
Vertical Res olution Max Input V Max Input Position Range ±5 divisions Delay between any Two
Channels (Typical) Offset Range 1 mV/div to 50 mV/div: ±1 V
Offset Accuracy 1 mV/div to 9.95 mV/div: ±0.2% × (offset – position) ±0.1 div ±1.5 mV
Channel-to-Channel Isolation (Any two channels at equal Vertical Scale settings) (Typical)
em Analog Channels
oltage, 1 M
Voltage, 50
4
1 GHz 2.5 GHz 3.5 GHz 460 ps 300 ps 160 ps 115 ps 310 ps 200 ps 100 ps 95 ps
Depending on instrument model: 3.0 GHz, 2.5 GHz, 2 GHz, 1 GHz, 500 MHz, 250 MHz, and 20 M Hz
1MΩ ±1%with13pF±2pF,50±1%
50 : 1 mV/div to 1 V/div 8bit(>11b
±150 V CAT I
100 ps (5
10 mV/div to 99.5 mV/div: ±0.35% × (offset – position) ±0.1 div ±1.5 mV
100 mV/div to 1 V/div: ±0.35% × (offset – position) ±0.1 div ±15 mV
1.01 V/div to 10 V/div: ±0.25% × (offset – position) ±0.1 div ±150 mV
,derateat20dB/decadeto9V
5V
0 , DC coupling and equal V/div at or above 10 mV/div)
50.5 mV/div to 99.5 mV/div: ±(1.5 V – 10 divisions) 100 mV/div to 500 mV/div: ±10 V
505 mV/div to 995 mV/div: ±(15 V – 10 divisions)
1V/divto5V/div: ±100V
5.05 V/div to 10 V/div: ±(150 V – 10 divisions)
30:1 between 100 MHz and 2.5 GHz
20:1 between 2.5 GHz and 3.5 GHz
it with Hi Res)
, with peaks ±24 V
RMS
100:1 at 100 MHz
above 200 kHz
RMS
www.tektronix.com 11
Data Sheet
Horizontal System Analo g Channels
Characteristic DPO7054C DPO7104C DPO7104C with Option 2SR DPO7254C / DPO7354C
Maximum Sample Rate (1 ch) 20 GS/s 20 GS/s 40 GS/s 40 GS/s Maximum Sample Rate (2 ch) 10 GS/s 10 GS/s 20 GS/s 20 GS/s Maximum Sample Rate (3-4 ch) 5 GS/s 5 GS/s 10 GS/s 10 GS/s Maximum Equivalent Time
Sampling Rate Maximum Record Length with
50M (1 ch), 25M (2 ch), 12.5M (3-4 ch)
Standard Conguration Maximum Record Length with
125M (1 ch), 50M (2 ch), 25M (3-4 ch)
Option 2RL Maximum Re
cord Length with
250M (1 ch), 125M (2 ch), 50M (3-4 ch)
Option 5RL Maximum Record Length with
Option 10RL
Maximum Duration at Highest
1-2 ms with standard record length, up to 10 ms with optional record length
Real-timeSampleRate(1ch) Time Base Range
50 ps/div to 1000 s/div 50 ps/div to 1000 s/div 25 ps/div to 1000 s/div 25 ps/div to 1000 s/div Time Resolution (in ET/IT mode) 500 fs 500 fs 250 fs 250 fs Time Base Delay Time Range 5 ns to 250 s Channel-to-Channel Deskew
Range Delta Time Measurement
((0.06 / sample rate) + (2.5 ppm × Reading)) RMS
Accuracy TriggerJitter(RMS) 1.5ps
Jitter Noise Floor
<1 ps
<100 fs
RMS
<2.5 ps
RMS
(<2 ps
<65 parts/trillion for record durations <10 s
Time Base Accuracy ±2.5 ppm + aging <1 ppm per year
4TS/s
±75 ns
with enhanced triggering OFF
with enhanced triggering ON
RMS
) for record duration <10 µs (typical)
Peak
for record duration <30 ms
RMS
500M (1 ch) 250M (2 ch)
125M (3-4 ch)
12 www.tektronix.com
Digital Phosphor Oscilloscopes — DPO7000C Series
Acquisition Modes
Mode Description
Sample Peak Detect
Acquire sampled values Captures narrow glitches at all real-time sampling rates:
1/sample rate at 10 GS/s
Averaging Envelope
From2to10,000waveformsincludedinaverage
9
From1to2×10
waveforms included in min-max
envelope
Hi Res Real-time boxcar averaging reduces random noise and
increases resolution
Roll
Scrolls sequential waveform points across the display in a right-to-left rolling motion at sweep speeds slower than50ms/div.Upto10MS/swithamaximumrecord length of 40M
FastAcq Acquisition Mode
FastAcq optimizes the instrument for analysis of dynamic signals and capture of infrequent events
Maximum FastAcq
>250,000 wfms/s on all 4 channels simultaneously
Waveform Capture Rate Waveform Database Accumulate waveform database providing
three-dimensional array of amplitude, time, and counts
FastFrame™ Acquisition Acquisition memory divided into segments; maximum
trigger rate >310,000 waveforms per second. Time of arrival recorded with each event. Frame Finder tool helps to visually identify transients
Pinpoint®Trigger System
Characteristic
Trigger Sensitivity
Description
Internal DC Coupled 0.7 div DC to 50 MHz, increasing to 1.2 div at rated
analog bandwidth (typical), up to 2.5 GHz; 2.5 div at
3.5 GHz
External (Auxiliary Input) 1M
Trigger Characteristics
A Event and Delayed B Event Trigger Types
250mVfromDCto50MHz,increasingto350mVat 250 MHz (typical)
Edge, Glitch, Width, Runt, Timeout, Transition Time, Logic Pattern, Logic State, Setup/Hold, Window – all except Edge, Pattern, and State can be Logic State
qualied by up to two channels Trigger Delay by Time 5 ns to 250 s Trigger Delay by Events 1 to 10,000,000 events
2
Optional Serial Protocol
I
C, SPI, RS-232, CAN, USB 2.0 Trigger Types (A Event only)
Main Trigger Modes Enhanced Triggering
Auto, Normal, and Single User-selectable; corrects the difference in timing
between the trigger path and the acquired data path (supports all Pinpoint trigger types on both A and B Events except pattern trigger and not available in FastAcq)
Characteristic
Trigger S equences
Main, Delayed by Time, Delayed by Events, Reset
Description
by Time, Reset by State, Reset by Transition. All sequences can include separate horizontal delay after the trigger event to position the acquisition window in time
Communications-related Triggers
Requires Opt. MTM. Support for AMI, HDB3, BnZS, CMI, MLT3, and NRZ encoded communications signals. Select among isolated positive or negative one, zero pulse form, or eye patterns as applicable to the standard
Video Trigger Formats and Field Rates
Triggers from negative sync composite video, eld 1 or eld 2 for interlaced systems, any eld, specic line, or any line for interlaced or noninterlaced systems. Supported systems include NTSC, PAL, SECAM, and HDTV 1080/24sF, 1080p/25, 1080i/50, 1080i/60, 1080p/24, 720p/60, 480p/60
Serial Pattern Trigger (DPO7254C and DPO7354C only, requires Opt. ST1G)
Up to 64-bit serial word recognizer, bit specied in binary (high, low, don’t care) or hex format. Trigger on NRZ-encoded data up to 1.25 Gb/s
Clock Recovery System (DPO7254C and DPO7354C only, requires Opt. ST1G
or MTM)
Clock Recovery
Fixed at FBaud/500 PhaseLockedLoop Bandwidth
Clock Recovery
1.5 MBaud to 1.25 GBaud
Frequency Range
ck Recovery Jitter
Clo
Clock Recovery
s
+ 1.25% Unit Interval RMS for PRBS data
20 p
RMS
terns
pat
s
+ 1.25% Unit Interval RMS for repeating
20 p
RMS
11” data pattern
"00
±5% of requested baud rate (typical) Tracking/Acquisition Range
Minimum Signal Amplitude Needed
1div
up to 1.25 GBaud (typical)
p-p
for Clock Recovery
Trigger Level Range
±12 divisions from center of screen
(Internal) Trigger Level (Aux In) TekVPI interface; ±5 V (50 ); 150 V CAT I, derate at
Trigger Level (Line)
20 dB/decade to 9 V
Fixed at 0 V
above 200 kHz (1 MΩ)
RMS
Trigger Coupling DC, AC (attenuates <60 Hz), HF Rej (attenuates
>30 kHz), LF Rej (attenuates <80 kHz), Noise Reject
(reduces sensitivity)
Trigger Holdoff Range
250 ns to 12 s
www.tektronix.com 13
Data Sheet
Trigger Modes
Mode Description
Edge
Glitch Trigger on or reject glitches of positive, negative,
Width
Runt
Window Trigger on an event that enters or exits a window
Timeout Trigger on an event which remains high, low, or either,
Transition
Setup/Hold Trigger on violations of both setup time and hold time
Logic Pattern
Logic State Any logical pattern of channels (1, 2, 3) clocked by edge
Parallel Bus Video
Visual Trigger (Optional) Provided as part of Opt. VET. Trigger on up to 8
Comm (Optional) Provided as part of Opt. MTM. Support for AMI, HDB3,
I2C (Optional) Provided as part of Opt. SR-EMBD. Trigger on Start,
SPI (Optional) Provided as part of Opt. SR-EMBD. Trigger on SS or
RS-232/422/485/UART (Optional)
Positive or negative slope on any channel or front-panel auxiliary input. Coupling includes DC, AC, HF reject, LF reject, and noise reject
or either polarity. Minimum glitch width is 170 ps (typical) with rearm time of 2 50 ps (for DPO7254C or DPO7354C)
Trigger on width of positive or negative pulse either within or outside of selectable limits (225 ps to 10 s)
Trigger on a pulse that crosses one threshold but fails to cross a second thresholdbeforecrossingtherst again. Event can be time or logic qualied
dened by two user-adjustable thresholds. Event can be time or logic qualied
for a specied time period (300 ps to 1 s) Trigger on pulse edge rates that are faster or slower
than specied. Slope may be positive, negative, or either
between clock and data present on any two input channels
Trigger when pattern goes false or stays true for specied period of time (300 ps to 1 s). Pattern (AND, OR, NAND, NOR) specied for all analog input channels dened as high, low, or don’t care
on channel 4. Trigger on rising or falling clock edge Trigger on specied data value on dened parallel bus Trigger on all lines, specic line number, odd, even,
or all elds on NTSC, PAL, SECAM, and HDTV 480p/60, 576p/50, 875i/60, 720p/30, 720p/50, 720p/60, 1080/24sF, 1080i/50, 1080p/25, 1080i/60, 1080p/24, 1080p/25, 1080p/50, 1080p/60, Bi-level, Tri-level
user-specied areas, including rectangle, triangle, trapezoid, and hexagon shapes
BnZS, CMI, MLT3, and NRZ encoded signals
Repeated Start, Stop, Missing ACK, Address (7 or 10 bit), Data (1-5 bytes), or Address and Data on I busesupto10Mb/s
data (10-16 words) on SPI buses up to 10 Mb/s Provided as part of Opt. SR-COMP. Trigger on Start Bit,
End of Packet, Data (1-5 words), and Parity Error on RS-232busesupto10Mb/s
2
C
Mode Description
USB 2.0 (Optional)
(Optional)
CAN
ial Pattern (Optional)
Ser
Provided as part of Opt. SR-USB.
Low Speed: Trigger on Sync, Reset, Suspend,
Resume, End of Packet, Token (Address) Packet, Data
Packet, Handshake Packet, Special Packet, Error.
Token Packet Trigger – Any token type, SOF, O UT, IN, SETUP; Address can be specied for Any, OUT, IN, and SETUP token types. Address can be further specied to trigger on ,<,=,>,, != a particular value, or inside or outside of a range. Frame number canbespecified for SOF token using Binary, Hex, Unsigned Decimal, and Don't Care digits. Data Packet Trigger – Any data type, DATA0, DATA1; Data can be further specied to trigger on ,<,=,>,, != a particular data value, or inside or outside of a range. Handshake Packet Trigger – Any handshake type, ACK, NAK, STALL. Special Packet Trigger – Any special type, Reserved. Error Trigger – PID Check, CRC5 or CRC16, Bit Stufng.
Full Speed: Trigger on Sync, Reset, Suspend, Resume,
End of Packet, Token (Address) Packet, Data Packet,
Handshake Packet, Special Packet, Error.
Token Packet Trigger – Any token type, SOF, O UT, IN, SETUP; Address can be specied for Any, OUT, IN, and SETUP token types. Address can be further specied to trigger on ,<,=,>,, != a particular value, or inside or outside of a range. Frame number canbespecified for SOF token using Binary, Hex, Unsigned Decimal, and Don't Care digits. Data Packet Trigger – Any data type, DATA0, DATA1; Data can be further specied to trigger on ,<,=,>,, != a particular data value, or inside or outside of a range. Handshake Packet Trigger – Any handshake type, ACK, NAK, STALL. Special Packet Trigger – Any special type, PRE, Reserved. Error Trigger – PID Check, CRC5 or CRC16, Bit Stufng.
High Speed: No protocol-level triggering.
Note: High Speed support only available on 1GHz
models.
videdaspartofOpt.LSA
Pro
vided as part of Opt. ST1G. Captures serial data
Pro
eam with built-in clock recovery for NRZ standards
str
o 1.25 Gb/s. Extended with pattern lock triggering
up t
apture repeated acquisitions of long serial data
to c
tterns
pa
Search and Mark Events
aracteristic
Ch
Advanced Search and Mark
Description
Automatically mark events and document waveforms.
Search positive/negative slopes or both, glitches,
runts, pulse widths, transition rate, setup and hold,
timeout, windows, or nd any logic or state pattern on
any number of channels. Search DDR Read or Write
bursts with Opt. DDRA. Event table summarizes all
found events. All events are time stamped in reference
to trigger position. Stop acquisitions when an event is
found
14 www.tektronix.com
Digital Phosphor Oscilloscopes — DPO7000C Series
Waveform Measurements
Measurement Description
Cursors Waveform and Screen Automatic Measurements
53, of which 8 can be displayed on-screen at any one time
Measurement Statistics Mean, Minimum, Maximum, Standard Deviation Reference Levels User-denable reference levels for automatic
measurements can be specied in either percent or units
Gating Isolate the specic occurrence within an acquisition
to take measurements on, using either screen or waveform cursors
Amplitude Related Amplitude, High, Low, Maximum, Minimum,
Peak-to-Peak, Mean, Cycle Mean, RMS, Cycle RMS, Positive Overshoot, Negative Overshoot
Time Related Rise Time, Fall Time, P ositive Width, Negative Width,
Positive Duty Cycle, Negative Duty Cycle, Period, Frequency, Delay
ation
Combin
rm Histogram
Wavefo
ements
Measur
Eye-pattern Measurements
ycle Area, Phase, Burst Width
Area, C
rm Count, Hits in Box, Peak Hits, Median,
Wavefo
m, Minimum, Peak-to-Peak, Mean (μ),
Maximu
rd Deviation (sigma), μ+1sigma, μ+2sigma,
Standa
gma
μ+3si Extinction Ratio (absolute, %, dB), Eye Height, Eye
Width, Eye Top, Eye Base, Crossing %, Jitter (p-p, RMS, 6sigma), Noise (p-p, RMS), Signal/Noise Ratio, Cycle Distortion, Q-factor
eform Histograms
Wav
veform histogram provides an array of data
Awa
ues representing the total number of hits inside
val
user-dened region of the display. A waveform
of a
togram is both a visual graph of the hit distribution as
his
ll as a numeric array of values that can be measured.
we
urces – Channel 1, Channel 2, Channel 3,
So
annel 4, Ref 1, Ref 2, Ref 3, Ref 4, Math 1, Math 2,
Ch
th 3, Math 4
Ma
pes – Vertical, Horizontal
Ty
Waveform Processing/Math
Characteristic
Number of Math
Description
Up to 4
Waveforms Arithmetic
Algebraic Expressions
Add, Subtract, Multiply, Divide waveforms and scalars Dene extensive algebraic expressions including
waveforms, scalars, user-adjustable variables, and results of parametric measurements. Perform math on math using complex equations. e.g. (Integral (CH1 – Mean(CH1)) × 1.414 × VAR1)
Math Functions
Relational Frequency Domain
Functions (FFT)
Average, Invert, Integrate, Differentiate, Square Root, Exponential, Log Sin, Cos, Tan, ASin, ACos, ATan, Sinh, Cosh, Tanh
,Loge, Abs, Ceiling, Floor, Min, Max,
10
Boolean result of comparison >, <, ≥, ≤, ==, != Spectral Magnitude and Phase, Real and Imaginary
Spectra
FFT Vertical Units Magnitude: Linear, dB, dBm
Phase: Degrees, radians, group delay
FFT Window Functions Rectangular, Hamming, Hanning, Kaiser-Bessel,
Blackman-Harris, Gaussian, Flattop2, Tek Exponential Waveform Denition Filtering Functions
As an arbitrary math expression
User-denable lters. Users specify a lter containing
the coefcients of the lter. Filter les provided Mask Function
A function that generates a waveform database pixmap
from a sample waveform. Sample count can be dened
Software
Software
NI LabVIEW SignalExpress Tektronix Edition
Description
A fully interactive measurement software environment optimized for the DPO7000C Series enables you to instantly acquire, generate, analyze, compare, import, and save measurement data and signals using an intuitive drag-and-drop user interface that does not require any programming. Standard DPO7000C Series support for acquiring, controlling, viewing, and exporting your live signal data is permanently available through the software. The full version (SIGEXPTE) adds additional signal processing, advanced analysis, mixed signal, sweeping, limit testing, and user-dened step capabilities and is available for a 30-day trial period standard with each instrument.
IVI Driver Provides a standard instrument programming
interface for common applications such as LabVIEW, LabWindows/CVI, Microsoft .NET and MATLAB. IVI-COM standard
LXI Class C Web Interface
Connect to the DPO7000C Series through a standard web browser by simply entering the oscilloscope’s IP address in the address bar of the browser. The web interface enables viewing of instrument status and conguration, as well as status and modication of network settings. A ll web interaction conforms to LXI Class C specication
Display Characteristics
Charac
teristic
Description
Display Type Liquid-crystal active-matrix color display with touch
screen
Display Size Diagonal: 12.1 in. (307 mm)
ay Resolution
Displ
1024 horizontal × 768 vertical pixels (XGA) Waveform Styles Vectors, Dots, Variable Persistence, Innite Persistence Color Palettes Normal, Green, Gray, Temperature, Spectral, and User
Dened Display Format YT, XY
Computer System and Perip herals
Characteristic
Operating System
Description
Windows 7 Ultimate 64-bit CPU Intel Core 2 Duo, 2 GHz processor PC System Memory 8GB Hard Disk Drive
Removable hard disk drive, 160 GB capacity (2.5 in.
SATA)
/DVD Drive
CD Mouse Keyboard
ont-panel CD-R/W, DVD-R drive
Fr
ptical wheel mouse, USB interface
O
rder 119-7083-xx for small keyboard; USB interface
O
nd hub
a
www.tektronix.com 15
Data Sheet
Input/Output Ports
Port Description
USB 2.0 High-speed Host Ports
Supports USB mass storage devices, printers, keyboard, and mouse. Ports on front and side panels of
the instrument. Can be disabled individually GPIB Port LAN Port Video Out Port
Rear-panel IEEE488.2 connector
RJ-45 connector, supports 10/100/1000BASE-T
DVI-I connector, connect to show the oscilloscope
display on an external monitor or projector. Support for
extended desktop and clone mode Audio Ports Miniature phono jacks Keyboard Port Mouse Port Auxiliary Input Auxiliary Out (Software
switchable)
PS/2 compatible
PS/2 compatible
Front-panel TekVPI connector. Max input 150 V CAT I
Trigger Out: A TTL compatible pulse when the
oscilloscope triggers
Time Base Reference Out: A TTL compatible output of
internal 10 MHz reference oscillator External Reference In
Time base system can phase lock to an external
10 MHz reference (10 MHz ±1%) Analog Signal Output BNC connector provides a buffered version of the Ch3
signal. 50 mV/div ±20% into a 1 Mload, 25 mV/div
±20% into a 50 load. Bandwidth is 100 MHz into
a50load Probe Compensator
Output
Front-panel pins
Amplitude: 1 V ±20% into a 50 load
Frequency: 1 kHz ±5% Recovered Clock
(DPO7254C and DPO7354C only)
Recovered Data (DPO7254C and
(Enabled by Opt. MTM.) BNC connector, 1.25 Gb/s,
output swing 130 mV
into 50
p-p
(Enabled by Opt. MTM.) BNC connector, 1.25 Gb/s,
output swing 200 mV into 50 DPO7354C only)
LAN eXtensions for Instrumentation (LXI)
Characteristic
Description
Class LXI Class C Version V1.3
Power Source
Characteristic
Description
PowerSource 100to240V±10%,47to63Hz,<550W
115 V
±10%, 360 to 440 Hz, CAT I, <500 VA
RMS
Physical Characteristics
Benchtop Conguration
Dimension
mm
in.
Height 292 11.48 Width 451 17.75 Depth 265 10.44
Weight kg lb.
Net 15 32 Shipping
Rackmount Conguration
Dimension mm in.
28.9 63.75
Height 331 12.25 Width 479 18.85 Depth (from rackmounting
231.75 9.12
ear to back of instrument)
Weight kg lb.
Net 17.4 37.5 Rackmount Kit 2.5
Required Cooling Clearance
Dimension mm in.
5.5
Top 0 0 Bottom 0 0 Left Side Right Side
76 3
00 Front 0 0 Rear 0 0
Environmental
Char
acteristic
Description
Temperature
Operating 0 °C to +50 °C, excluding CD-R/W drive
+10 °C to +45 °C, including CD-R/W drive
Nonoperating
–40 °C to +71 °C
Humidity
Operating 5% to 95% relative humidity (RH) with a maximum
wet bulb temperature of 29 °C at or below +50 °C, noncondensing. Upper limit derated to 45% RH from +30°Cto+50°C
Nonoperating
5% to 95% relative humidity (RH) with a maximum wet bulb temperature of 29 °C at or below +50 °C, noncondensing. Upper limit derated to 45% RH from +30°Cto+50°C
Altitude
Operating 10,000 ft. (3,048 m) Nonoperating
40,000 ft. (12,190 m)
Regulatory
Electromagnetic
2004/108/EC
Compatibility Certications UL61010-1, Second Edition; CSA61010-1 Second
Edition, EN61010-1:2001; IEC 61010-1:2001
16 www.tektronix.com
Digital Phosphor Oscilloscopes — DPO7000C Series
Ordering Information
DPO7000C Series
Product Description
DPO7054C 500 MHz, 5/10/20 GS/s (4/2/1 ch), 12.5M record length,
DPO7104C 1 GHz, 5/10/20 GS/s (4/2/1 ch), 12.5M record length,
DPO7254C 2.5 GHz, 10/20/40 GS/s (4/2/1 ch), 12.5M record
DPO7354C 3.5 GHz, 10/20/40 GS/s (4/2/1 ch), 12.5M record
All Models Include: One passive voltage probe per analog channel (P6139B:
500 MHz, 10X, 8 pF), accessory pouch, front cover, mouse, 013-0347-00 VGA to DVI adapter, quick-start user manual, DPO7000C Series product software media and documentation including performance verication and programmer’s manual, NI LabVIEW SignalExpress Tektronix Edition software, Calibration Certicate documenting measurement traceability to National Metrology Institute(s), Z 540-1 Compliance and ISO9001, power cord, one-year warranty.
Note: Please specify power plug and manual language version when ordering.
Instrument Options
Record Length Op tions
Option DPO7054C
Opt. 2RL 125M max, 25M/ch 125M max, 25M/ch Opt. 5RL 250M max, 50M/ch 250M max, 50M/ch Opt. 10RL
Sample Rate Options
Option DPO7104C DPO7054C
Opt. 2SR
Solid State Hard Disk Drive Options
Option
Opt. SSD Solid State Hard Disk Drive
4-channel digital phosphor oscilloscope
4-channel digital phosphor oscilloscope
length, 4-channel digital phosphor oscilloscope
length, 4-channel digital phosphor oscilloscope
DPO7254C
DPO7104C
DPO7354C
500M max, 125M/ch
DPO7254C DPO7354C
Double maximum
real-timesamplerateto
40/20/10 GS/s on 1/2/4 ch
Description
Software Options
Option
Opt. DDRA*
1, 2
Description
DDR Memory Bus Analysis Opt. DJA Jitter and Eye Analysis Tools – Advanced (DPOJET) Opt. D-PHY*
1, 3
MIPI®D-PHY Essentials – Transmitter Debug,
Characterization, and Compliance Test Solution Opt. DVI* Opt. ET3*
4
5
Digital Visual Interface Compliance Testing
Ethernet Compliance Testing Opt. LSA Low-speed Automotive Serial Analysis, includes CAN
Trigger, CAN/LIN Decode and Analysis Opt. LT Waveform Limit Testing Opt. MTM Mask Testing for ITU-T, ANSI T1.102, Ethernet,
SONET/SDH, Fibre Channel, USB 2.0, IEEE 1394b,
Rapid I/O, OIF, CPRI, and Serial Video; (includes
hardware clock recovery on DPO7254C/DPO7354C) Opt. PWR
Power Measurement and Analysis Opt. SR-COMP Computer Serial Triggering and Analysis
(RS-232/422/485/UART). Enables triggering on
packet-level information on RS-232/422/485/UART
buses as well as analytical tools such as digital views of
the signal, bus views, and packet decoding Opt. SR-CUST Custom Serial Analysis Kit for Developers Opt. SR-DPHY MIPI®D-PHY Serial Analysis. Enables analysis of
MIPI DSI-1 and CSI-2 buses with analytical tools such
as digital views of the signal, bus views, and packet
decoding Opt. SR-EMBD Embedded Serial Triggering and Analysis (I2C, SPI).
Enables triggering on packet-level information on I
2
C and SPI buses as well as analytical tools such as digital views of the signal, bus views, and packet decoding
Opt. SR-USB USB 2.0 Serial Triggering and Analysis (LS, FS,
HS). Enables triggering on packet-level content for low-speed and full-speed USB serial buses. Also enables analytical tools such as digital views of the signal, bus views, and packet decoding for low-speed, full-speed, and high-speed USB serial buses. USB High Speed supported only on 1GHzmodels
Opt. ST1G*
3
8b/10b Serial Protocol Trigger and Decode up to
1.25 Gb/s
Opt. SVE SignalVu Essentials Vector Signal Analysis Opt. SVM* Opt. SVO* Opt. SVP* Opt. SVT* Opt. USB*
6
6
6
6
8
SignalVu General Purpose Modulation Analysis Flexible OFDM Analysis SignalVu Pulse Advanced Signal Analysis Settling Time Measurements – Frequency and Phase USB 2.0 Compliance Testing
Opt. VET Visual Trigger and Search
TekExpress Application Framework
TEKEXP TekExpress Application Framework TEKEXP Opt.
D-PHYTX*
1, 3
TEKEXP Opt. HEAC*
D-PHY Automated Solution
3, 7
HEAC Automated Solution
TEKEXP Opt. XGbT*410GBASE-T Automated Solution
Bundle Options
Opt. PS1 Power Solution Bundle: DPOPWR, P5205A, TCP0030,
TPA-BNC, 067-1686-xx (Deskew Fixture)
*1Requires Opt. DJA.
2
Available on 1GHzmodelsonly.
*
3
Available on 2.5 GHz models only.
*
4
*
Available on DPO7354C model only.
5
Requires TF-GBE-BTP or TF-GBE-ATP Ethernet Test Fixture.
*
6
Requires Opt. SVE.
*
7
*
Requires Opt. 2RL, DJA, MTM, and ST1G.
8
Requires TDSUSBF (USB Test Fixture). 2 GHz bandwidth required for high-speed USB.
*
www.tektronix.com 17
Data Sheet
Floating Option Licenses
Floating licenses offer an alternative method to manage your Tektronix asset. Floating licenses allow license-key enabled options to be easily moved among all your MSO/DPO5000, DPO7000, and DPO/DSA/MSO70000 Series of Tektronix oscilloscopes. Floating licenses are available for the following license-key enabled options.
Check www.tek.com/products/oscilloscopes/oatinglicenses for additional information about oating license options.
Option
DPOFL-DDRA*
1, 2
Description
DDR Memory Bus Analysis DPOFL-DJA Jitter and Eye Analysis Tools – Advanced (DPOJET) DPOFL-D-PHY*
1, 3
MIPI®D-PHY Transmitter Debug, Characterization and
Compliance Test Solution DPOFL-DVI* DPOFL-ET3*
4
5
Digital Visual Interface Compliance Testing
Ethernet Compliance Testing DPOFL-LSA Low-speed Automotive Serial Analysis, includes CAN
Trigger, CAN/LIN Decode and Analysis DPOFL-LT Waveform Limit Testing DPOFL-MTM Mask Testing for ITU-T, ANSI T1.102, Ethernet,
SONET/SDH, Fibre Channel, USB 2.0, IEEE 1394b,
Rapid I/O, OIF, CPRI, and Serial Video; (includes
hardware clock recovery on DPO7254C/DPO7354C) DPOFL-PWR
Power Measurement and Analysis DPOFL-SR-COMP Computer Serial Triggering and Analysis
(RS-232/422/485/UART). Enables triggering on
packet-level information on RS-232/422/485/UART
busesaswellasanalyticaltoolssuchasdigitalviewsof
the signal, bus views, and packet decoding DPOFL-SR-CUST Custom Serial Analysis Kit for Developers DPOFL-SR-DPHY MIPI®D-PHY Serial Analysis. Enables analysis of
MIPI DSI-1 and CSI-2 buses with analytical tools such
as digital views of the signal, bus views, and packet
decoding DPOFL-SR-EMBD Embedded Serial Triggering and Analysis (I2C, SPI).
Enables triggering on packet-level information on I
2
C andSPIbusesaswellasanalytical tools such as digital views of the signal, bus views, and packet decoding
DPOFL-SR-USB USB 2.0 Serial Triggering and Analysis (LS, FS,
HS). Enables triggering on packet-level content for low-speed and full-speed USB serial buses. Also enables analytical tools such as digital views of the signal, bus views, and packet decoding for low-speed, full-speed, and high-speed USB serial buses. USB High Speed supported only on 1GHzmodels
DPOFL- ST1G*
3
8b/10b Serial Protocol Trigger and Decode up to
1.25 Gb/s
DPOFL-SVE SignalVu Essentials Vector Signal Analysis DPOFL-SVM* DPOFL-SVO* DPOFL-SVP* DPOFL-SVT* DPOFL-USB*
6
6
6
6
8
SignalVu General Purpose Modulation Analysis Flexible OFDM Analysis SignalVu Pulse Advanced Signal Analysis Settling Time Measurements – Frequency and Phase USB 2.0 Compliance Testing
DPOFL-VET Visual Trigger and Search
*1Requires Opt. DJA.
2
Available on 1 GHz models only.
*
3
*
Available on 2.5 GHz models only.
4
Available on DPO7354C model only.
*
5
Requires TF-GBE-BTP or TF-GBE-ATP Ethernet Test Fixture.
*
6
*
Requires Opt. SVE.
8
Requires TDSUSBF (USB Test Fixture). 2 GHz bandwidth required for high-speed USB.
*
Power Plug Options
Option
Opt. A0 Opt. A1 Opt. A2 Opt. A3
Description
North America Universal European Union UK
Australia Opt. A5 Switzerland Opt. A6
Japan Opt. A10 China Opt. A11 Opt. A12 Opt. A99
India
Brazil
No power cord
User Manual Options
Option
Opt. L0 Opt. L1
Description
English manual
French manual Opt. L3 German manual Opt. L5
Japanese manual Opt. L7 Simplied Chinese manual Opt. L8 Traditional Chinese manual Opt. L9 Opt. L10 Opt. L99
Service Options*
Option
Korean manual
Russian manual
No user manual
9
Description
Opt. C3 Calibration Service 3 Years Opt. C5 Calibration Service 5 Years Opt. D1 Calibration Data Report Opt. D3 Calibration Data Report 3 Years (with Opt. C3) Opt. D5 Calibration Data Report 5 Years (with Opt. C5) Opt. G3 Complete Care 3 Years (includes loaner, scheduled
calibration and more) Opt. G5 Complete Care 5 Years (includes loaner, scheduled
calibration and more) Opt. R3 Repair Service 3 Years (including warranty) Opt. R5 Repair Service 5 Years (including warranty)
*9Probes and accessories are not included in the oscilloscope warranty. Refer to the data sheet for each
probe for its unique warranty and calibration terms.
18 www.tektronix.com
Digital Phosphor Oscilloscopes — DPO7000C Series
Recommended Accessories
Probes
Tektronix offers over 100 different probes to meet your application needs. For a comprehensive listing of available probes, please visit www.tektronix.com/probes.
Probe Description
TAP3500 TAP2500 TAP1500 TDP3500
TDP1500
TDP1000
TDP0500
TCP0150 20 MHz TekVPI™ 150 Ampere AC/DC current probe TCP0030 120 MHz TekVPI 30 Ampere AC/DC current probe TMDP0200 THDP0200 THDP0100 P5100A 2.5 kV, 500 MHz, 100X high-voltage passive probe P6015A 20 kV, 75 MHz high-voltage passive probe P6158
*10Requires TekVPI®to TekProbe BNC adapter (TPA-BNC).
Accessories
Accessory Description
077-0076-xx 077-0010-10 077-0063-05
SIGEXPTE NI LabVIEW SignalExpress Tektronix Edition Software
016-1985-02 Rackmount Kit 065-0881-xx 016-1979-xx 119-7083-xx 119-6297-xx 016-1970-xx K420
3.5 GHz TekVPI active single-ended probe
2.5 GHz TekVPI active single-ended probe
1.5 GHz TekVPI active single-ended probe
3.5 GHz TekVPI differential voltage probe with ±2 V differential input voltage
1.5 GHz TekVPI differential voltage probe with ±8.5 V differential input voltage
1 GHz TekVPI differential voltage probe with ±42 V differential input voltage
500 MHz TekVPI differential voltage probe with ±42 V differential input voltage
±750 V, 200 MHz high-voltage differential probe ±1.5 kV, 200 MHz high-voltage differential probe ±6 kV, 100 MHz high-voltage differential probe
3 GHz, 20X low-capacitance passive probe
Service Manual (English PDF only) Programmer Manual (English PDF only) Performance Verication and Specications Manual
(English PDF only)
(Full Version)
Removable HD Spare with rotational media Front HD option for Rackmount Kit Mini Keyboard (USB interface) Full-size keyboard with 4-port USB hub Transit Case Oscilloscope Cart
Cables
Cable
012-0991-xx 012-0991-xx
Description
GPIB Cable (1 m)
GPIB Cable (2 m)
Test Fixtures
Fixture Description
067-1686-xx
Probe Calibration / Power Deskew Test Fixture TDSUSBF Test xture for use with Opt. USB TF-GBE-BTP Basic test package for 10/100/1000BASE-T Ethernet
tests TF-GBE-ATP Advanced test package for 10/100/1000BASE-T
Ethernet (includes 1000BASE-T jitter test channel
cable) TF-GBE-EE Additional test xture for Energy Efcient Ethernet
measurements. Order through Crescent Heart
Software (http://www.c-h-s.com)
Adapters
Adapter Description
TPA-BNC TekVPI -t o-TekProbe BNC Adapter
10
P6701B*
10
P6703B*
*10Requires TekVPI®to TekProbe BNC adapter (TPA-BNC).
Optical/Electrical Converter (Multi Mode)
Optical/Electrical Converter (Single Mode)
Software
Software
Description
SIGEXPTE NI LabVIEW SignalExpress™ Tektronix Edition
Software (Full Version)
www.tektronix.com 19
Data Sheet
Instrument Upgrades
To upgrade your DPO7000C Series oscilloscope, order DPO-UP and option listed below. For example, DPO-UP DDRA.
Option
Description
To upgrad e record length:
RL02 RL05 RL010
From Standard Conguration to Opt. 2RL Conguration From Standard Conguration to Opt. 5RL Conguration From Standard Conguration to Opt. 10RL
Conguration RL25 RL210
From Opt. 2RL Conguration to Opt. 5RL Conguration
From Opt. 2RL Conguration to Opt. 10RL
Conguration RL510
From Opt. 5RL Conguration to Opt. 10RL
Conguration
To upgrade DPO7000C Series with:
1, 2
DDRA* DJAM
Add Opt. DDRA
Add Opt. DJA – Jitter and Eye Analysis Tools -
Advanced (DPOJET)
1, 3
D-PHY*
AddOpt. D-PHY–MIPI®D-PHY Transmitter Debug,
Characterization, and Compliance Test Solution
4
DVI*
Add Opt. DVI – Digital Visual Interface Compliance
Testin g
5
ET3*
Add Opt. ET3 – Ethernet Compliance Testing LSA Add Opt. LSA – CAN/LIN Trigger, Decode, and
Analysis LT MTM PWR
Add Opt. LT – Waveform Limit Testing
Add Opt. MTM – Mask Testing
Add Opt. PWR – Power Measurement and Analysis SR-COMP Add Opt. SR-COMP – Computer Serial Triggering and
Analysis (RS-232/422/485/UART) SR-CUST Add Opt. SR-CUST – Custom Serial Analysis Kit for
Developers
Option
Description
SR-DPHY Add Opt. SR-DPHY – MIPI®D-PHY Serial Analysis
(DSI-1 and CSI-2)
SR-EMBD Add Opt. SR-EMBD – Embedded Serial Triggering and
Analysis (I
2
C, SPI)
SR-USB Add Opt. SR-USB – USB 2.0 Serial Triggering and
Analysis (LS, FS, HS)
SSD Add Opt. SSD – Solid State Hard Drive
3
ST1G*
Add Opt. ST1G – 8b/10b Serial Protocol Trigger and Decode up to 1.25 Gb/s
SVEM Add Opt. SVE – SignalVu Essentials Vector Signal
Analysis
6
SVM*
Add Opt. SVM – SignalVu General Purpose Modulation Analysis
6
SVO* SVP*
6
Add Opt. SVO – Flexible OFDM Analysis Add Opt. SVP – SignalVu Pul se Advanced Signal
Analysis
6
SVT*
AddOpt. SVT–SettlingTimeMeasurements­Frequency and Phase
8
USB* VETM
*1Requires Opt. DJA.
2
Available on 1GHzmodelsonly.
*
3
*
Available on 2.5 GHz models only.
4
*
Available on DPO7354C model only.
5
Requires TF-GBE-BTP or TF-GBE-ATP Ethernet Test Fixture.
*
6
*
Requires Opt. SVE.
8
Requires TDSUSBF (USB Test Fixture). 2 GHz bandwidth required for high-speed USB.
*
Tektronix is registered to ISO9001 and ISO 14001 by SRI Quality System Registrar.
Add Opt. USB – USB 2.0 Compliance Testing Add Opt. VET – Visual Trigger and Search
20 www.tektronix.com
Digital Phosphor Oscilloscopes — DPO7000C Series
www.tektronix.com 21
Data Sheet
22 www.tektronix.com
Digital Phosphor Oscilloscopes — DPO7000C Series
www.tektronix.com 23
Data Sheet
Contact Tektronix:
ASEAN / Australa
Balkans, Israel, South Africa and other ISE Countries +41 52 675 3777
Central East Eu
Mexico, Central/South America & Caribbean 52 (55) 56 04 50 90
Middle E as t,
* European toll-free number. If not accessible, call: +41 52 675 3777
rope and the Baltics +41526753777
Central Europe & Greece +41 52 675 3777
Asia, and North Africa +41 52 675 3777
The Netherlands 00800 2255 4835*
People’s Rep
Republic of
United K ingdom & Ireland 00800 2255 4835*
sia (65) 6356 3900
Austria 00800 2255 4835*
Belgium 00800 22
Brazil +55(11)37597627
Canada 1 800 833 9200
Denmark +4580881401
Finland +41526
France 00800 2255 4835*
Germany 00800 2255 4835*
Hong Kong 400 8
India 000 800 650 1835
Italy 00800 2255 4835*
Japan 81 (3) 67
Luxembourg +41526753777
ublic of China 400 820 5835
Poland +41 52 675 3777
Korea 001 800 8255 2835
Russia & CIS +7 (495) 7484900
South Africa +41526753777
Spain 00800
Sweden 008 00 2255 4835*
Switzerland 00800 2255 4835*
Tai wa n 886 (
55 4835*
75 3777
20 5835
14 3010
Norway 800 16098
Portugal 80 08 12370
2255 4835*
2) 2722 9622
USA 1 800 833 9200
Updated 10 February 2011
www.tektronix.com
For Further Information. Tektronix maintains a comprehensive, constantly expanding collection of application notes, t echnical briefs and other resources to h elp engineers working on the cutting edge of technology. Please visit www.tektronix.com
t © Tektronix, Inc. All rights reserved. Tektronix products are covered by U.S. and foreign patents,
Copyrigh
d pending. Information in this publication supersedes that in all previously published material.
issued an
tion and price change privileges reserved. TEKTRONIX and TEK are registered trademarks of
Specica
x, Inc. All other trade names referenced are the service marks, trademarks, or registered trademarks
Tek t ro n i
espective companies.
of their r
19 Jan 2012 48W-26543-6
Loading...