Tektronix DPO77002SX, DPO75902SX, DPO75002SX, DPO73304SX, DPO72304SX Performance Verification

...

Download

DPO70000SX Series Oscilloscopes

Technical Reference

*P077104305*

077-1043-05

DPO70000SX Series Oscilloscopes

Technical Reference

Warning

The servicing instructions are for use by qualified personnel only. To avoid personal injury, do not perform any servicing unless you are qualified to do so. Refer to all safety summaries prior to performing service.

Supports Product Firmware V10.0 and above.

www.tek.com

077-1043-05

Copyright © Tektronix. All rights reserved. Licensed software products are owned by Tektronix or its subsidiaries or suppliers, and are protected by national copyright laws and international treaty provisions. Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication supersedes that in all previously published material. Specifications and price change privileges reserved.

TEKTRONIX and TEK are registered trademarks of Tektronix, Inc.

Contacting Tektronix

Tektronix, Inc. 14150 SW Karl Braun Drive P.O. Box 500 Beaverton, OR 97077 USA

For product information, sales, service, and technical support:

■

In North America, call 1-800-833-9200.

■

Worldwide, visit www.tek.com to find contacts in your area.

Warranty

Tektronix warrants that this product will be free from defects in materials and workmanship for a period of one (1) year from the date of shipment. If any such product proves defective during this warranty period, Tektronix, at its option, either will repair the defective product without charge for parts and labor, or will provide a replacement in exchange for the defective product. Parts, modules and replacement products used by Tektronix for warranty work may be new or reconditioned to like new performance. All replaced parts, modules and products become the property of Tektronix.

In order to obtain service under this warranty, Customer must notify Tektronix of the defect before the expiration of the warranty period and make suitable arrangements for the performance of service. Customer shall be responsible for packaging and shipping the defective product to the service center designated by Tektronix, with shipping charges prepaid. Tektronix shall pay for the return of the product to Customer if the shipment is to a location within the country in which the Tektronix service center is located. Customer shall be responsible for paying all shipping charges, duties, taxes, and any other charges for products returned to any other locations.

This warranty shall not apply to any defect, failure or damage caused by improper use or improper or inadequate maintenance and care. Tektronix shall not be obligated to furnish service under this warranty a) to repair damage resulting from attempts by personnel other than Tektronix representatives to install, repair or service the product; b) to repair damage resulting from improper use or connection to incompatible equipment; c) to repair any damage or malfunction caused by the use of non-Tektronix supplies; or d) to service a product that has been modified or integrated with other products when the effect of such modification or integration increases the time or difficulty of servicing the product.

THIS WARRANTY IS GIVEN BY TEKTRONIX WITH RESPECT TO THE PRODUCT IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED. TEKTRONIX AND ITS VENDORS DISCLAIM ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. TEKTRONIX' RESPONSIBILITY TO REPAIR OR REPLACE DEFECTIVE PRODUCTS IS THE SOLE AND EXCLUSIVE REMEDY PROVIDED TO THE CUSTOMER FOR BREACH OF THIS WARRANTY. TEKTRONIX AND ITS VENDORS WILL NOT BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES IRRESPECTIVE OF WHETHER TEKTRONIX OR THE VENDOR HAS ADVANCE NOTICE OF THE POSSIBILITY OF SUCH DAMAGES.

[W2 – 15AUG04]

Contacting Tektronix ......................................................................................................................... 0

Important safety information .............................................................................................................. iii

General safety summary ................................................................................................................ iii

Terms in the manual ...................................................................................................................... vi

Terms on the product ..................................................................................................................... vi

Symbols on the product ................................................................................................................. vi

Specifications

Vertical system analog channels ..................................................................................................... 1

Horizontal and acquisition system ................................................................................................ 15

Trigger specifications ................................................................................................................... 18

Serial trigger specifications .......................................................................................................... 25

Input-output port specifications .................................................................................................... 25

Data storage specifications ........................................................................................................... 28

Power source specification ........................................................................................................... 28

Mechanical specifications ............................................................................................................. 29

Environmental specifications ....................................................................................................... 30

Performance verification

Performance verification .............................................................................................................. 31

Conventions .................................................................................................................................. 32

Brief procedures ........................................................................................................................... 34

Self tests ........................................................................................................................................ 34

Functional tests ............................................................................................................................. 35

Verify all analog input channels ................................................................................................... 36

Verify the time base ...................................................................................................................... 38

Verify the A (Main) and B (Delayed) trigger systems ................................................................. 40

Verify the file system ................................................................................................................... 41

Performance tests .......................................................................................................................... 42

Prerequisites .................................................................................................................................. 43

Equipment required ...................................................................................................................... 43

Test record .................................................................................................................................... 48

Signal acquisition system checks ................................................................................................. 79

Check DC voltage measurement accuracy, ATI channel ............................................................. 80

Check DC voltage measurement accuracy, TekConnect channels ............................................... 83

Check DC gain accuracy, ATI channel ........................................................................................ 90

DPO70000SX Series i

Table of Contents

Check DC gain accuracy, TekConnect channels .......................................................................... 93

Check offset accuracy, ATI channel ........................................................................................... 109

Check offset accuracy, TekConnect channels ............................................................................ 112

Check analog bandwidth, ATI channel ...................................................................................... 117

Check channel bandwidth, TekConnect channels ...................................................................... 120

Check Input Resistance, ATI channel ........................................................................................ 125

Check input resistance, TekConnect channels ........................................................................... 126

Time base system checks ............................................................................................................ 128

Check timebase and delay time accuracy and reference ............................................................ 128

Check delta time measurement accuracy .................................................................................... 132

Trigger system checks ................................................................................................................ 137

Check time qualified trigger accuracy ........................................................................................ 137

Check sensitivity edge trigger DC coupled ................................................................................ 141

Output signal checks ................................................................................................................... 148

Check fast edge output ............................................................................................................... 148

Sine wave generator leveling procedure ..................................................................................... 153

Method 1 ................................................................................................................................ 153

Method 2 ................................................................................................................................ 155

ii DPO70000SX Series

Important safety information

This manual contains information and warnings that must be followed by the user for safe operation and to keep the product in a safe condition.

General safety summary

Use the product only as specified. Review the following safety precautions to avoid injury and prevent damage to this product or any products connected to it. Carefully read all instructions. Retain these instructions for future reference.

This product shall be used in accordance with local and national codes.

For correct and safe operation of the product, it is essential that you follow generally accepted safety procedures in addition to the safety precautions specified in this manual.

The product is designed to be used by trained personnel only.

Only qualified personnel who are aware of the hazards involved should remove the cover for repair, maintenance, or adjustment.

Before use, always check the product with a known source to be sure it is operating correctly.

This product is not intended for detection of hazardous voltages.

Use personal protective equipment to prevent shock and arc blast injury where hazardous live conductors are exposed.

DPO70000SX Series iii

Important safety information

To avoid fire or personal

injury

Use proper power cord. Use only the power cord specified for this product and

certified for the country of use. Do not use the provided power cord for other products.

Ground the product. This product is grounded through the grounding conductor of the power cord. To avoid electric shock, the grounding conductor must be connected to earth ground. Before making connections to the input or output terminals of the product, ensure that the product is properly grounded. Do not disable the power cord grounding connection.

Power disconnect. The power cord disconnects the product from the power source. See instructions for the location. Do not position the equipment so that it is difficult to operate the power cord; it must remain accessible to the user at all times to allow for quick disconnection if needed.

Connect and disconnect properly. Do not connect or disconnect probes or test leads while they are connected to a voltage source. Use only insulated voltage probes, test leads, and adapters supplied with the product, or indicated by Tektronix to be suitable for the product.

Observe all terminal ratings. To avoid fire or shock hazard, observe all rating and markings on the product. Consult the product manual for further ratings information before making connections to the product. Do not exceed the Measurement Category (CAT) rating and voltage or current rating of the lowest rated individual component of a product, probe, or accessory. Use caution when using 1:1 test leads because the probe tip voltage is directly transmitted to the product.

Do not apply a potential to any terminal, including the common terminal, that exceeds the maximum rating of that terminal.

Do not operate without covers. Do not operate this product with covers or panels removed, or with the case open. Hazardous voltage exposure is possible.

Avoid exposed circuitry. Do not touch exposed connections and components when power is present.

Do not operate with suspected failures. If you suspect that there is damage to this product, have it inspected by qualified service personnel.

Disable the product if it is damaged. Do not use the product if it is damaged or operates incorrectly. If in doubt about safety of the product, turn it off and disconnect the power cord. Clearly mark the product to prevent its further operation.

Before use, inspect voltage probes, test leads, and accessories for mechanical damage and replace when damaged. Do not use probes or test leads if they are damaged, if there is exposed metal, or if a wear indicator shows.

Examine the exterior of the product before you use it. Look for cracks or missing pieces.

Use only specified replacement parts.

Do not operate in wet/damp conditions. Be aware that condensation may occur if a unit is moved from a cold to a warm environment.

Do not operate in an explosive atmosphere.

iv DPO70000SX Series

Important safety information

Keep product surfaces clean and dry. Remove the input signals before you clean the product.

Provide proper ventilation. Refer to the installation instructions in the manual for details on installing the product so it has proper ventilation.

Slots and openings are provided for ventilation and should never be covered or otherwise obstructed. Do not push objects into any of the openings.

Provide a safe working environment. Always place the product in a location convenient for viewing the display and indicators.

Avoid improper or prolonged use of keyboards, pointers, and button pads. Improper or prolonged keyboard or pointer use may result in serious injury.

Be sure your work area meets applicable ergonomic standards. Consult with an ergonomics professional to avoid stress injuries.

Use care when lifting and carrying the product. This product is provided with a handle or handles for lifting and carrying.

WARNING. The product is heavy. To reduce the risk of personal injury or damage to the device get help when lifting or carrying the product.

Probes and test leads

Use only the Tektronix rackmount hardware specified for this product.

Before connecting probes or test leads, connect the power cord from the power connector to a properly grounded power outlet.

Keep fingers behind the protective barrier, protective finger guard, or tactile indicator on the probes.

Remove all probes, test leads and accessories that are not in use.

Use only correct Measurement Category (CAT), voltage, temperature, altitude, and amperage rated probes, test leads, and adapters for any measurement.

DPO70000SX Series v

Important safety information

Terms in the manual

These terms may appear in this manual:

WARNING. Warning statements identify conditions or practices that could result in injury or loss of life.

CAUTION. Caution statements identify conditions or practices that could result in damage to this product or other property.

Terms on the product

These terms may appear on the product:

■

DANGER indicates an injury hazard immediately accessible as you read the marking.

Symbols on the product

■

WARNING indicates an injury hazard not immediately accessible as you read the marking.

■

CAUTION indicates a hazard to property including the product.

When this symbol is marked on the product, be sure to consult the manual to find out the nature of the potential hazards and any actions which have to be taken to avoid them. (This symbol may also be used to refer the user to ratings in the manual.)

The following symbols may appear on the product:

vi DPO70000SX Series

Specifications

This chapter contains specifications for the instrument. All specifications are guaranteed unless noted as "typical." Typical specifications are provided for your convenience but are not guaranteed. Specifications that are marked with the symbol are checked in Performance Verification.

All specifications apply to all models unless noted otherwise. To meet specifications, the following conditions must first be met:

■

The instrument must have been adjusted in an ambient temperature range between 18 °C and 28 °C.

■

The instrument must be powered from a source that meets the specifications.

■

The instrument must have been operating continuously for twenty minutes within the specified operating temperature range. (60 minutes continuous operation required if the ambient relative humidity is greater than 60%.)

■

You must perform the Signal Path Compensation (SPC) operation described in the user manual and the online help. If the operating temperature changes by more than 5 °C, you must perform the SPC operation again.

Vertical system analog channels

Number of channels ≥50 GHz models: 2+1,

<50 GHz models: Four channels, all identical

Input connector

TekConnect channels: TekConnect. Power supply compatible with VPI.

ATI channel: Male 1.85 mm coax.

Input coupling

TekConnect channels: Two modes: DC, 50 ohms to a programmable termination voltage; Ground.

The termination can be connected to a DC voltage:

≤ 1.2 VFS settings: -3.5 V to 3.5 V,

> 1.2 VFS settings: 0.0 V

ATI channel: DC, 50 Ω.

DPO70000SX Series 1

Specifications Vertical system analog channels (cont.)

Input resistance

≤1.2 VFS settings 50 Ω ±3% at 18 to 28 ºC (64 to 82 ºF)

50 Ω ±4% over 5 to 45 ºC (45 to 113 ºF)

>1.2 VFS settings 50 Ω ±4.4% over 5 to 45 ºC (45 to 113 ºF)

ATI channel 50 Ω ±3% from 18 °C to 28 °C

50 Ω ±4% from 5 °C to 45 °C

Maximum input voltage

TekConnect channels: ≤1.2 VFS settings:

±1.5 V relative to the termination bias (30 mA maximum)

±5 V absolute maximum input

>1.2 VFS settings:

±8 V. Limited by maximum Vterm current and the attenuator power rating at maximum temperature.

ATI channel: ±0.75 V

Aux channel: ±5.0 V

Input termination voltage (VTerm) range, TekConnect channels

≤1.2 VFS settings: -3.5 V to +3.5 V

>1.2 VFS settings: 0 V

Input VSWR, typical Measured with a TekConnect TCA-292D adaptor and a network analyzer.

≤1.2 VFS settings: 0 – 17 GHz: 1.4:1

17 – 20 GHz: 1.6:1

20 – 33 GHz: 2.0:1

>1.2 VFS settings: 0 – 17 GHz: 1.4:1

17 – 33 GHz: 2.0:1

ATI channel: 0-20GHz: 1.7:1

>20-33 GHz: 2.0:1

> 33-70 GHz: 3.0:1

Number of digitized bits 8 bits

Digitizer nonlinearity (typical) < 1.0 DL (digitization level), differential; < 1 DL integral, independently based

Sensitivity range

TekConnect channels 62.5 mVFS to 6 V

ATI channel 100 mVFS to 300 mVFS.

DC gain accuracy ± 2%

2 DPO70000SX Series

Vertical system analog channels (cont.) Specifications

DC voltage measurement

Net offset = offset - (position × volts/division).

accuracy, Sample, Average, and Hi-Res modes

Full scale setting DC measurement accuracy

62.5 mVFS – 6 V

Delta voltage reading

62.5 mVFS – 6 V

Position range ± 5 divisions

Offset range

TekConnect channels

ATI channel

Full Scale voltage range Offset range

62.5 mVFS – 1.2 V

>1.2 VFS – 6 V

Full Scale voltage range Offset range

100 mVFS – 300 mV

Offset accuracy Net offset = offset - (position × volts/division).

Full scale voltage range Offset accuracy

62.5 mVFS to 1.2 VFS (TekConnect channels) ±(0.4% | net offset | + 0.2% | net offset – Vterm

>1.2 VFS to 6 VFS (TekConnect channels) ±(0.6% | net offset | + 13.4 mV + 1% FS)

100 mVFS to 300 mVFS (ATI channel) ±(0.35% | net offset | + 2 mV + 1% FS)

±(Gain accuracy x | vertical value - net offset |) + offset accuracy + 0.4% x FS

±(Gain accuracy x | Delta voltage measured | +

0.008 x FS

±3.4 V

±6 V

±300 mV - (10 div × Volts/div)

setting | + 2.5 mV + 1% FS)

Analog bandwidth Bandwidth with a TCA292D adapter on TekConnect channels or directly into ATI channel.

Ambient temperature 18ºC to 28ºC assumed for all guaranteed bandwidth specifications.

Enhanced bandwidth is guaranteed at the following full scale (FS) stepped gain settings:

TekConnect channels: 62.5 mV, 100 mV, 200 mV, 500 mV, 1 V, 2 V, and 5 V.

ATI channel: All settings from 100 mV through 300 mV.

For ATI channels, the full scale settings range is 100 mVFS to 300 mVFS.

DPO70000SX Series 3

Specifications Vertical system analog channels (cont.)

Instrument Channel BW settings Bandwidth

DPO77002SX ATI, 1 Ch 70 GHz BWE >67 GHz

70 GHz typical

DPO77002SX

TekConnect, 2 Ch No BWE >33 GHz All

DPO73304SX

DPO77002SX

TekConnect, 2 Ch 33 GHz BWE >33 GHz 100 GS/s

DPO73304SX

DPO77002SX DPO73304SX

TekConnect, 2 Ch TekConnect, 4 Ch

23 GHz BWE >23 GHz 50 GS/s

DPO75902SX ATI, 1 Ch 59 GHz BWE >59 GHz 200 GS

DPO75902SX

ATI, 1 Ch 50 GHz BWE >50 GHz 200 GS

DPO75002SX

DPO75902SX TekConnect No BWE >33 GHz All

DPO75002SX TekConnect No BWE >25 GHz All

DPO75002SX TekConnect 25 GHz BWE >25 GHz 100 GS/s

DPO75002SX TekConnect 23 GHz BWE >23 GHz 50 GS/s

DPO72304SX TekConnect No BWE >23 GHz 50 GS/s, 100 GS/s

DPO72304SX TekConnect 23 GHz BWE >23 GHz 50 GS/s, 100 GS/s

DPO71604SX TekConnect 16 GHz BWE >16 GHz 50 GS/s, 100 GS/s

DPO71304SX TekConnect 13 GHz BWE >13 GHz 50 GS/s, 100 GS/s

Sample rate

200 GS

TekConnect channel

ATI channel

Typical temperature derating

Frequency TC, (dB/°C) 5 °C 45 °C

DC - 5 GHz 0.005 dB/°C 0.07 -0.09

10 GHz 0.010 dB/°C 0.13 -0.17

15 GHz 0.025 dB/°C 0.33 -0.43

20 GHz 0.045 dB/°C 0.59 -0.77

23 GHz 0.10 dB/°C 1.30 -1.70

25 GHz 0.10 dB/°C 1.30 -1.70

30 GHz 0.115 dB/°C 1.50 -1.96

33 GHz 0.160 dB/°C 2.08 -2.72

Typical temperature derating

Frequency TC, (dB/°C)

DC - 10 GHz 0.002 dB/°C

15 GHz 0.005 dB/°C

20 GHz 0.01 dB/°C

30 GHz 0.05 dB/°C

40 GHz 0.07 dB/°C

To determine the amount of performance derating above the temperature limit, use the Typical Temperature Variation table.

200 GS/s is the only sample rate available on the ATI channel.

4 DPO70000SX Series

Vertical system analog channels (cont.) Specifications

Typical temperature derating

Frequency TC, (dB/°C)

50 GHz 0.05 dB/°C

60 GHz 0.05 dB/°C

67 GHz 0.05 dB/°C

Frequency response tolerance

All modes, BWE on, 18 ºC to 28 ºC (typical)

TekConnect channel: Step settings TekConnect channels: 77.5 mVFS, 151 mVFS, 302 mVFS, 605 mVFS, 1210 mVFS.,

ATI channel: All volts/div settings

To determine the amount of performance derating above the temperature limit, use the Typical Temperature Variation table

1620 mV

3240 mV

FS,

±0.5 dB from DC to 50% of nominal BW

±1.5 dB from 50% to 80% of nominal BW

All other gain settings:

±1.0 dB from DC to 50% of nominal BW

±2.0 dB from 50% to 80% of nominal BW

±0.5 dB from DC to 20 GHz

±0.75 dB from >20 GHz to 30 GHz

±1.25 dB from >30 GHz to 68.5 GHz

±2 dB from >68.5 GHz to 69.5 GHz

+2 / -3 dB at 70 GHz

DPO70000SX Series 5

Specifications Vertical system analog channels (cont.)

TekConnect channel

ATI channel

Typical temperature derating

Frequency TC, (dB/°C) 5 °C 45 °C

DC - 5 GHz 0.005 dB/°C 0.07 -0.09

10 GHz 0.010 dB/°C 0.13 -0.17

15 GHz 0.025 dB/°C 0.33 -0.43

20 GHz 0.045 dB/°C 0.59 -0.77

23 GHz 0.10 dB/°C 1.30 -1.70

25 GHz 0.10 dB/°C 1.30 -1.70

30 GHz 0.115 dB/°C 1.50 -1.96

33 GHz 0.160 dB/°C 2.08 -2.72

Typical temperature derating

Frequency TC, (dB/°C)

DC - 5 GHz 0.005 dB/°C

DC - 10 GHz 0.002 dB/°C

15 GHz 0.005 dB/°C

20 GHz 0.01 dB/°C

30 GHz 0.05 dB/°C

40 GHz 0.07 dB/°C

50 GHz 0.05 dB/°C

60 GHz 0.05 dB/°C

Calculated rise time (typical)

Calculated risetimes for specified instrument bandwidths

Instrument bandwidth BWE On BWE Off

10% - 90% 20% - 80% 10% - 90% 20% - 80%

70 GHz 5.6 ps 4.3 ps n/a n/a

50 GHz 7.8 ps 6 ps n/a n/a

33 GHz 13 ps 9 ps 21 ps 14 ps

25 GHz 16 ps 12 ps 22 ps 15 ps

23 GHZ 17 ps 13 ps 24 ps 16 ps

6 DPO70000SX Series

Vertical system analog channels (cont.) Specifications

Step response settling time (typical)

BWE off

BWE on (fastest BWE setting) (typical)

The time by which the step response enters and stays below the indicated % error. Step transition occurs at the 50% amplitude point of the step leading edge.

Instrument Gain setting (FS) Settling Error

Amount Time

DPO77002SX TekConnect channels

DPO75902SX TekConnect channels

DPO75002SX TekConnect channels

DPO73304SX 62.5 mV, 100 mV, 200 mV,

DPO72304SX 62.5 mV, 100 mV, 200 mV,

BWE on (fastest BWE setting) Instrument Gain setting (FS) Settling

Instrument Gain setting (FS) Settling Error

DPO77002SX, DPO75902SX, DPO75002SX ATI channel

DPO77002SX, DPO75902SX, DPO75002SX TekConnect channels

DPO73304SX, DPO72304SX

62.5 mV, 100 mV, 200 mV, 500 mV, 1.0 V, 1.2 V, 1.4 V, 2 V, 4 V

500 mV, 1.0 V, 1.2 V, 1.4 V, 2 V, 4 V

100 mV, 200 mV, 300 mV <3.5%

62.5 mV, 100 mV, 200 mV, 500 mV,

1.0 V, 1.2 V, 1.4 V, 2 V, 4 V

62.5 mV, 100 mV, 200 mV, 500 mV,

1.0 V, 1.2 V, 1.4 V, 2 V, 4 V

<6% <5.5% <3%

<6% <5% <3%

150 ps – 400 ps 400 ps – 3 ns 3 ns – 1 ms

Amount Time

150 ps – 400 ps <2.5% <1.5%

<3.5% <2.5% <1.5%

400 ps – 3 ns

3 ns – 1 ms

150 ps – 400 ps

400 ps – 3 ns

3 ns – 1 ms

150 ps – 400 ps

400 ps – 3 ns

3 ns – 1 ms

DPO70000SX Series 7

Specifications Vertical system analog channels (cont.)

Effective bits, typical. The following charts give the typical effective bits for a 225 mV p-p sine-wave input sampled at

250 mVFS and maximum sample rate.

DPO77002SX DPO75902SX DPO75002SX

Input Frequency 200 GS/s 70 GHz 200 GS/s 59 GHz 200 GS/s 50 GHz

10 MHz 5.0 bits 5.13 bits 5.22 bits

0.92 GHz 5.0 bits 5.13 bits 5.21 bits

1.92 GHz 5.0 bits 5.13 bits 5.21 bits

2.92 GHz 5.0 bits 5.14 bits 5.21 bits

3.92 GHz 5.0 bits 5.13 bits 5.21 bits

4.92 GHz 4.9 bits 5.02 bits 5.10 bits

5.92 GHz 4.9 bits 5.03 bits 5.10 bits

6.92 GHz 4.9 bits 5.02 bits 5.09 bits

7.92 GHz 4.9 bits 5.02 bits 5.08 bits

8.92 GHz 4.9 bits 5.02 bits 5.09 bits

9.92 GHz 4.9 bits 5.03 bits 5.10 bits

10.92 GHz 4.9 bits 5.03 bits 5.10 bits

11.92 GHz 4.9 bits 5.07 bits 5.14 bits

12.92 GHz 4.9 bits 5.06 bits 5.18 bits

13.92 GHz 4.9 bits 5.08 bits 5.20 bits

14.92 GHz 4.9 bits 5.11 bits 5.22 bits

15.92 GHz 4.8 bits 4.98 bits 5.11 bits

16.92 GHz 4.8 bits 4.88 bits 5.05 bits

17.92 GHz 4.7 bits 4.75 bits 4.90 bits

18.92 GHz 4.7 bits 4.76 bits 4.92 bits

19.92 GHz 4.7 bits 4.80 bits 4.93 bits

20.92 GHz 4.7 bits 4.81 bits 4.93 bits

21.92 GHz 4.6 bits 4.76 bits 4.85 bits

22.92 GHz 4.6 bits 4.81 bits 4.89 bits

23.92 GHz 4.8 bits 4.87 bits 4.94 bits

24.92 GHz 4.7 bits 4.83 bits 4.89 bits

25.92 GHz 4.7 bits 4.84 bits 4.92 bits

26.92 GHz 4.6 bits 4.86 bits 4.93 bits

27.92 GHz 4.6 bits 4.82 bits 4.90 bits

28.92 GHz 4.6 bits 4.85 bits 4.94 bits

29.92 GHz 4.6 bits 4.85 bits 4.95 bits

30.92 GHz 4.6 bits 4.74 bits 4.90 bits

31.92 GHz 4.5 bits 4.70 bits 4.80 bits

32.92 GHz 4.5 bits 4.58 bits 4.74 bits

33.92 GHz 4.5 bits 4.67 bits 4.76 bits

35.92 GHz 4.5 bits 4.60 bits 4.67 bits

8 DPO70000SX Series

Vertical system analog channels (cont.) Specifications

DPO77002SX DPO75902SX DPO75002SX

37.92 GHz 4.3 bits 4.41 bits 4.47 bits

39.92 GHz 4.3 bits 4.57 bits 4.65 bits

41.92 GHz 4.4 bits 4.49 bits 4.62 bits

43.92 GHz 4.6 bits 4.71 bits 4.87 bits

45.92 GHz 4.4 bits 4.54 bits 4.71 bits

47.92 GHz 4.4 bits 4.53 bits 4.64 bits

49.92 GHz 4.4 bits 4.60 bits 4.68 bits

51.92 GHz 4.5 bits 4.72 bits

53.92 GHz 4.6 bits 4.63 bits

55.92 GHz 4.5 bits 4.57 bits

57.92 GHz 4.5 bits 4.43 bits

59.92 GHz 4.8 bits 4.90 bits

61.92 GHz 4.8 bits

63.92 GHz 4.9 bits

65.92 GHz 4.9 bits

67.92 GHz 4.9 bits

69.92 GHz 4.7 bits

BWE on, Enhanced MIMO filter, full bandwidth

DPO70002SX, DPO75902SX, DPO75002SX, DPO73304SX TekConnect channels

Input frequency 100 GS/s, 33 GHz 50 GS/s, 23 GHz 100 GS/s, 23 GHz 50 GS/s, 23 GHz

10 MHz 5.4 bits 5.4 bits 5.9 bits 5.3 bits

1 GHz 5.2 bits 5.3 bits 5.8 bits 5.2 bits

2 GHz 5.2 bits 5.2 bits 5.7 bits 5.2 bits

3 GHz 5.1 bits 5.1 bits 5.6 bits 5.1 bits

4 GHz 5.1 bits 5.2 bits 5.6 bits 5.2 bits

5 GHz 5.2 bits 5.1 bits 5.6 bits 5.1 bits

6 GHz 5.0 bits 5.1 bits 5.6 bits 5.0 bits

7 GHz 5.0 bits 5.1 bits 5.5 bits 5.1 bits

8 GHz 5.1 bits 5.1 bits 5.6 bits 5.1 bits

9 GHz 5.1 bits 5.0 bits 5.6 bits 5.0 bits

10 GHz 5.2 bits 5.1 bits 5.5 bits 5.0 bits

11 GHz 5.1 bits 4.9 bits 5.4 bits 4.9 bits

12 GHz 5.2 bits 5.0 bits 5.5 bits 5.0 bits

13 GHz 5.1 bits 4.9 bits 5.4 bits 4.9 bits

14 GHz 5.1 bits 4.9 bits 5.3 bits 4.8 bits

15 GHz 4.9 bits 4.8 bits 5.1 bits 4.8 bits

DPO72304SX

DPO70000SX Series 9

Specifications Vertical system analog channels (cont.)

DPO70002SX, DPO75902SX, DPO75002SX, DPO73304SX TekConnect channels

16 GHz 4.8 bits 4.8 bits 5.2 bits 4.7 bits

17 GHz 4.9 bits 4.8 bits 5.2 bits 4.7 bits

18 GHz 4.9 bits 4.8 bits 5.3 bits 4.8 bits

19 GHz 4.8 bits 4.8 bits 5.2 bits 4.7 bits

20 GHz 4.7 bits 4.6 bits 5.1 bits 4.7 bits

21 GHz 4.8 bits 4.8 bits 5.3 bits 4.8 bits

22 GHz 4.8 bits 4.9 bits 5.3 bits 4.8 bits

23 GHz 4.9 bits 5.2 bits

24 GHz 5.0 bits

25 GHz 4.8 bits

26 GHz 4.9 bits

27 GHz 4.8 bits

28 GHz 4.7 bits

29 GHz 4.9 bits

30 GHz 4.9 bits

31 GHz 4.8 bits

32 GHz 4.8 bits

33 GHz 4.8 bits

DPO72304SX

10 DPO70000SX Series

Vertical system analog channels (cont.) Specifications

BWE on, full bandwidth Nine division sine wave input at the indicated frequency, sampled at 500 mVFS vertical sensitivity

and maximum sample rate

DPO73304SX, DPO77002SX, DPO75902SX, DPO75002SX TekConnect channels

Input frequency 100 GS/s, 33 GHz 50 GS/s, 23 GHz 100 GS/s, 23 GHz 50 GS/s, 23 GHz

10 MHz 5.4 bits 5.2 bits 6.0 bits 5.2 bits

1 GHz 4.9 bits 5.0 bits 5.5 bits 5.0 bits

2 GHz 4.9 bits 5.0 bits 5.3 bits 5.0 bits

3 GHz 5.0 bits 4.9 bits 5.4 bits 4.9 bits

4 GHz 4.5 bits 4.8 bits 4.8 bits 4.5 bits

5 GHz 4.7 bits 4.7 bits 5.3 bits 4.7 bits

6 GHz 4.8 bits 4.7 bits 5.2 bits 4.7 bits

7 GHz 4.9 bits 4.8 bits 5.3 bits 4.8 bits

8 GHz 5.0 bits 4.8 bits 5.4 bits 4.8 bits

9 GHz 5.0 bits 4.7 bits 5.3 bits 4.7 bits

10 GHz 5.0 bits 4.7 bits 5.4 bits 4.7 bits

11 GHz 5.0 bits 4.7 bits 5.2 bits 4.7 bits

12 GHz 5.1 bits 4.7 bits 5.3 bits 4.7 bits

13 GHz 4.7 bits 4.7 bits 5.2 bits 4.7 bits

14 GHz 5.0 bits 4.8 bits 5.2 bits 4.8 bits

15 GHz 4.8 bits 4.6 bits 5.1 bits 4.6 bits

16 GHz 4.6 bits 4.6 bits 5.2 bits 4.6 bits

17 GHz 4.8 bits 4.6 bits 5.1 bits 4.6 bits

18 GHz 4.7 bits 4.6 bits 5.1 bits 4.6 bits

19 GHz 4.5 bits 4.6 bits 5.0 bits 4.6 bits

20 GHz 4.4 bits 4.5 bits 5.0 bits 4.6 bits

21 GHz 4.4 bits 4.6 bits 5.1 bits 4.6 bits

22 GHz 4.6 bits 4.6 bits 5.1 bits 4.6 bits

23 GHz 4.6 bits 5.1 bits

24 GHz 4.7 bits

25 GHz 4.7 bits

26 GHz 4.6 bits

27 GHz 4.6 bits

28 GHz 4.6 bits

29 GHz 4.6 bits

30 GHz 4.6 bits

31 GHz 4.5 bits

32 GHz 4.5 bits

33 GHz 4.5 bits

DPO72304SX

DPO70000SX Series 11

Specifications Vertical system analog channels (cont.)

Full analog bandwidth

DPO73304SX, DPO77002SX, DPO75902SX, DPO75002SX TekConnect channels

Input frequency 100 GS/s 50 GS/s 100 GS/s 50 GS/s

10 MHz 5.2 bits 5.2 bits 5.4 bits 5.2 bits

1 GHz 4.8 bits 4.8 bits 5.0 bits 5.0 bits

2 GHz 4.9 bits 4.9 bits 5.1 bits 5.0 bits

3 GHz 4.8 bits 4.8 bits 5.1 bits 4.9 bits

4 GHz 4.7 bits 4.7 bits 4.7 bits 4.7 bits

5 GHz 4.7 bits 4.7 bits 4.8 bits 4.7 bits

6 GHz 4.7 bits 4.7 bits 4.8 bits 4.7 bits

7 GHz 4.7 bits 4.7 bits 4.9 bits 4.7 bits

8 GHz 4.6 bits 4.6 bits 4.9 bits 4.8 bits

9 GHz 4.6 bits 4.7 bits 4.9 bits 4.7 bits

10 GHz 4.7 bits 4.7 bits 4.9 bits 4.7 bits

11 GHz 4.7 bits 4.7 bits 4.9 bits 4.7 bits

12 GHz 4.7 bits 4.7 bits 4.9 bits 4.7 bits

13 GHz 4.5 bits 4.5 bits 4.8 bits 4.5 bits

14 GHz 4.7 bits 4.7 bits 4.9 bits 4.7 bits

15 GHz 4.6 bits 4.6 bits 4.7 bits 4.6 bits

16 GHz 4.4 bits 4.5 bits 4.7 bits 4.5 bits

17 GHz 4.4 bits 4.5 bits 4.7 bits 4.5 bits

18 GHz 4.4 bits 4.5 bits 4.6 bits 4.5 bits

19 GHz 4.1 bits 4.2 bits 4.5 bits 4.5 bits

20 GHz 4.2 bits 4.3 bits 4.5 bits 4.5 bits

21 GHz 4.5 bits 4.5 bits 4.6 bits 4.5 bits

22 GHz 4.4 bits 4.5 bits 4.8 bits 4.5 bits

23 GHz 4.4 bits 4.5 bits 4.8 bits 4.3 bits

24 GHz 4.5 bits 4.4 bits

25 GHz 4.4 bits 4.5 bits

26GHz 4.3 bits 4.4 bits

27 GHz 4.3 bits 4.1 bits

28 GHz 4.1 bits 4.1 bits

29 GHz 3.8 bits 4.2 bits

30 GHz 4.2 bits 4.2 bits

31 GHz 4.2 bits 4.4 bits

32 GHz 4.1 bits 4.1 bits

33 GHz 4.2 bits 4.3 bits

DPO72304SX

12 DPO70000SX Series

Vertical system analog channels (cont.) Specifications

Noise (typical)

Gain setting, full scale, BWE off

62.5 mV 0.88 mV 0.79 mV 0.74 mV 0.70 mV

100 mV 0.96 mV 0.86 mV 0.82 mV 0.79 mV

200 mV 1.53 mV 1.41 mV 1.30 mV 1.32 mV

500 mV 4.19 mV 3.14 mV 3.00 mV 3.05 mV

1 V 8.30 mV 6.10 mV 5.90 mV 6.08 mV

2.0 V 18.84 mV 14.19 mV 13.07 mV 13.09 mV

3.0 V 24.64 mV 19.09 mV 18.37 mV 18.37 mV

4.0 V 37.91 mV 26.01 mV 25.35 mV 25.55 mV

5.0 V 43.36 mV 31.84 mV 30.52 mV 30.62 mV

6.0 V 47.93 mV 36.97 mV 35.91 mV 36.33 mV

Gain setting, full scale, BWE on

62.5 mV 0.84 mV 0.84 mV 0.75 mV 0.72 mV 0.78 mV 0.77 mV 0.71 mV 0.69 mV

100 mV 0.93 mV 0.93 mV 0.78 mV 0.82 mV 0.77 mV 0.81 mV 0.68 mV 0.73 mV

150 mV 1.31 mV 1.29 mV 1.08 mV 1.19 mV 0.94 mV 1.01 mV 0.88 mV 0.95 mV

200 mV 1.52 mV 1.60 mV 1.14 mV 1.43 mV 1.04 mV 1.18 mV 0.99 mV 1.14 mV

300 mV 2.49 mV 2.52 mV 2.10 mV 2.29 mV 1.58 mV 1.8 mV 1.57 mV 1.79 mV

400 mV 2.92 mV 3.12 mV 2.58 mV 2.29 mV 1.82 mV 2.20 mV 1.82 mV 2.21 mV

500 mV 3.55 mV 3.80 mV 2.65 mV 3.38 mV 2.17 mV 2.66 mV 2.2 mV 2.69 mV

600 mV 4.86 mV 4.86 mV 4.14 mV 4.42 mV 3.02 mV 3.46 mV 3.01 mV 3.43 mV

700 mV 5.25 mV 5.39 mV 4.64 mV 4.96 mV 3.28 mV 3.85 mV 3.25 mV 3.80 mV

800 mV 5.76 mV 6.08 mV 5.08 mV 5.52 mV 3.61 mV 4.37 mV 3.56 mV 4.29 mV

900 mV 6.30 mV 6.66 mV 5.63 mV 6.13 mV 3.96 mV 4.81 mV 3.89 mV 4.69 mV

1 V 6.80 mV 7.30 mV 5.09 mV 6.54 mV 4.29 mV 5.29 mV 4.2 mV 5.14 mV

1.1 V 8.69 mV 9.02 mV 7.79 mV 8.20 mV 5.48 mV 6.94 mV 5.45 mV 6.74 mV

1.2 V 9.12 mV 9.60 mV 8.28 mV 8.72 mV 5.75 mV 7.50 mV 5.73 mV 7.28 mV

2.0 V 15.40 mV 14.53 mV 11.66 mV 14.65 mV 9.70 mV 12.23 mV 9.88 mV 11.87 mV

3.0 V 19.91 mV 19.82 mV 15.31 mV 20.51 mV 12.98 mV 16.55 mV 13.19 mV 16.81 mV

4.0 V 28.83 mV 27.85 mV 21.61 mV 27.84 mV 19.56 mV 23.17 mV 18.64 mV 21.32 mV

5.0 V 34.32 mV 32.80 mV 25.69 mV 34.07 mV 22.82 mV 27.79 mV 21.82 mV 26.03 mV

6.0 V 39.82 mV 38.96 mV 29.65 mV 39.18 mV 26.65 mV 32.42 mV 25.74 mV 31.45 mV

DPO77002SX, DPO75902SX, DPO75002SX, DPO73304SX TekConnect channels

100 GS/s 50 GS/s 100 GS/s 50 GS/s 100 GS/s 50 GS/s 100 GS/s 50 GS/s

DPO77002SX, DPO75902SX, DPO75002SX, DPO73304SX TekConnect channels

DPO72304SX DPO71604SX DPO71304SX

DPO70000SX Series 13

Specifications Vertical system analog channels (cont.)

Gain setting, full scale, ATI channel DPO77002SX

DPO75902SX, DPO75002SX

100 mV 1.19 mV

200 mV 1.76 mV

250 mV 2.10 mV

300 mV 2.49 mV

Channel-to-channel crosstalk (channel isolation), typical

Input frequency range (up to the rated bandwidth). Assumes two channels with the same scale and bandwidth settings. The limits apply up to the bandwidth of the particular instrument.

ATI models

Specified channels Instrument frequency range Isolation

ATI channels (isolation between any two [or more] ATI channels in separate units), requires UltraSync

TekConnect channels in an ATI unit (isolation between channels 1 and 3)

TekConnect channels to ATI channel (isolation between channels 1 and 3 to channel 2)

ATI channel to TekConnect (non-ATI) channels (isolation between channel 2 and channels 1 or 3)

DC to 70 GHz 70 dB

DC to 33 GHz 60 dB

DC to 4 GHz 55 dB

>4 GHz to 10 GHz 45 dB

>10 GHz to 20 GHz 35 dB

>20 GHz to 30 GHz 30 dB

>30 GHz to 33 GHz 27 dB

DC to 3 GHz 55 dB

>3 GHz to 12 GHz 40 dB

>12 GHz to 33 GHz 30 dB

>33 to 70 GHz 60 dB

TekConnect models (non-ATI)

Specified channels Instrument frequency range Isolation

Isolation between channels 1 or 2 and channels 3 or 4

Isolation between channels 1 and 2, or channels 3 and 4

Measurement category The measuring terminals on this product are not rated for connection to mains or Measurement

Category II, III or IV circuits.

TekConnect interface The instrument TekConnect channels support the TekConnect interface.

DC to 33 GHz 60 dB

DC to 2 GHz 60 dB

>2 to 10 GHz 42 dB

>10 to 20 GHz 35 dB

>20 to 33 GHz 30 dB

14 DPO70000SX Series

Horizontal and acquisition system

Specifications

Delay between channels, full bandwidth, equivalent time, BWE off, without deskew (typical)

Delay between channels, BWE (typical)

Channel skew stability, UltraSync (typical)

Real-time sample rate range

Equivalent-time sample rate or interpolated waveform rate range

Maximum record length, sample mode

≤ 1 ps between any two channels at any gain setting at 25 °C ±5 °C.

Derate linearly to ≤3 ps at 5 °C and 45 °C

≤ 500 fs between any two channels within the same box at any gain setting at 25 °C ±5 °C prior to any user adjustment. Manual adjustment available with 10 fs minimum resolution. Derate linearly to ≤ 1.5 ps at 5 °C and 45 °C.

≤ 250 fs Derate linearly to ≤ 3 ps at 5 °C and 45 °C.

Channels Sample rate, maximum

TekConnect channels Up to 100 GS/s

ATI channels 200 GS/s only

Equivalent-time acquisition can be enabled or disabled. When disabled, waveforms are interpolated at the fastest time base settings.

Up to 5 TS/s (waveform interval down to 0.2 ps) in E.T. and 0.2 ps resolution in trigger placement.

The maximum record length depends on the installed record length options. Maximum record length is less in serial trigger mode, hi-res mode, or when using the FIR filter.

between any two channels between instruments at any gain setting at 25 °C ±5 °C.

RMS

(Standard)

500,000,000 points (all channels), 1 G samples on 1–2 channels at 50 GS/s and 100 GS/s sample rates or greater (interpolated or equivalent time)

Maximum record length, HiRes mode

Record length limits

Seconds division range Fastest sweep speed is 10 ps per division

Internal time-base reference frequency

Half the record length of sample mode

Operation 4 X 50 GS/s

Acquisition

Display acquired waveform

Waveform data CURVE? output any PI

Math1 = Ch1 - Ch3 250 Msamples 250 Msamples 250 Msamples

Arbfilt (Ch1, "filter")

FFTmag(Ch1)

Reference Waveforms (Rn)

10 MHz

Electronically adjustable over about ±10 ppm.

500 Msamples 1 Gsamples 1 Gsamples

1 Gsamples 1 Gsamples 1 Gsamples

2 x 100 GS/s Acquisition

1 x 200 GS/s Acquisition

DPO70000SX Series 15

Specifications Horizontal and acquisition system (cont.)

Time base accuracy ±0.8 x 10-6 (within 1st year), ±0.3 x 10-6 aging/year after first year when operated within 23° C ±5°

C after 30 minute warm-up.

Typical: ±0.1 x 10-6 initial accuracy after adjustment.

Timing jitter (aperture uncertainty), (typical)

Measured at the maximum sample rate.

External Reference Low with ~0 dBm input drive at 10 MHz

TekConnect:

<100 fs rms for record durations less than 10 μs

<120 fs rms for record durations less than 100 μs

<140 fs rms for record durations less than 10 ms

<300 fs rms for record durations less than 10 s

ATI:

<65 fs rms for record durations less than 10 μs

External Reference Hi with ~0 dBm input drive at 10 MHz

TekConnect:

<100 fs rms for record durations less than 2 μs

<500 fs rms for record durations less than 10 s

ATI:

<65 fs rms for record durations less than 10 μs

For external reference in high (tracking) mode, the input reference must be low noise and the edge slew rate must exceed 1.5 V/ns to achieve the typical jitter results.

Internal Reference

TekConnect:

<100 fs rms for record durations less than 10 μs

<120 fs rms for record durations less than 100 μs

<140 fs rms for record durations less than 5 ms

ATI:

<65 fs rms for record durations less than 10 μs

For internal reference, specification assumes no signal attached to the external reference input.

Jitter noise floor (typical) Applies to time periods as long as 10.0 ns. Typical jitter noise floor is measured at the maximum,

BWE enabled bandwidth:

DPO77002SX <250 fs

DPO75902SX <250 fs

DPO75002SX <250 fs

DPO73304SX <250 fs

DPO72304SX <250 fs

Calculate the jitter noise floor (JNF) for a given instrument setting using the following formula:

16 DPO70000SX Series

Horizontal and acquisition system (cont.) Specifications

= typical input-referred noise spec (volts rms)

typ

FN = 1.3 for instrument bandwidth ≤9 GHz; 1.5 for instrument bandwidth ≥10 GHz

SR = slew rate around the measurement

FI = (1.7 x 10–2)/sqrt(2) = 1.2 x 10–2

tr = rise time of the measurement edge

tj = timebase jitter or aperture uncertainty

TBA = timebase accuracy (2 ppm)

JNF

The interpolated sample rate of the waveform must be at least 25 times the bandwidth of the signal being measured.

Acquisition update rate (typical)

DPO models 300,000 waveforms per second maximum

RMS

= (N

typ

× FN)2×

(

× t

+ t

seconds

RMS

+ F

)

Delta time measurement

accuracy

The formula to calculate the maximum delta-time measurement accuracy (DTAmax) for a given instrument setting and input signal is given below (assumes insignificant signal content above Nyquist and insignificant error due to aliasing, overdrive recovery and overdrive interpolation):

= typical input-referred noise spec (volts rms)

typ

FN = 1.3 for instrument bandwidth ≤9 GHz; 1.5 for instrument bandwidth ≥10 GHz

SR1 = slew rate around 1st point in measurement (1st edge)

SR2 = slew rate around 2nd point in measurement (2nd edge)

FI = 1.2 × 10–2

tr1 = rise time of first edge

tr2 = rise time of second edge

tj = sample jitter/aperture uncertainty (about 100 fs for time durations less than 10 μs)

Peak-peak based on statistical accumulation of 500 waveforms.

(

)

rms

pk-pk

(

seconds

DTA

MAX

=10 × (N

RMS is guaranteed regardless of data-gathering duration.

typ

× FN)

DTA

(

MAX

)

+ F

)

×(t

)

+ t

)

+ (2 × t

)

= (N

typ

The term under the square-root sign is the stability and is due to time interval error (TIE).

× FN)

(

)

(

×(t

+ t

)

+ F

)

+ (2 × t

)

DPO70000SX Series 17

Specifications

Trigger specifications

Trigger jitter DC coupled A edge (typical)

Edge trigger sensitivity DC

coupled (typical)

10 fs using enhanced trigger placement.

1 ps rms for low frequency, fast rise time signal, A edge, holdoff time = 30 μs

All sources, positive or negative edge.

Trigger Source Sensitivity

A-Event trigger ≤ 5%FS from DC to 50 MHz

≤ 7.5%FS at 5 GHz ≤ 10%FS at 10 GHz ≤ 15%FS at 15 GHz ≤ 35%FS at 20 GHz ≤ 50%FS at 25 GHz

B-Event trigger ≤ 5%FS from DC to 50 MHz

≤ 7.5%FS at 5 GHz ≤ 10%FS at 10 GHz ≤ 15%FS at 15 GHz ≤ 35%FS at 20GHz ≤ 50%FS at 25 GHz

Auxiliary input 100 mVpp from DC to 1 GHz

175 mVpp at 4 GHz 225 mVpp at 8 GHz 450 mVpp at 10 GHz 800 mVpp at 11 GHz

Trigger sensitivity TPC (typical) The minimum signal levels required for stable triggering of a waveform when the hardware is

incapable of doing so (excessive frequency, small input).

Trigger Source Sensitivity

A Event trigger, Ch1 – Ch4 20%×FS from DC to instrument bandwidth

B Event trigger, Ch1 – Ch4 20%×FS from DC to instrument bandwidth

18 DPO70000SX Series

+ 142 hidden pages

Tektronix DPO77002SX, DPO75902SX, DPO75002SX, DPO73304SX, DPO72304SX Performance Verification

Specifications and Main Features

Frequently Asked Questions

User Manual

Table of Contents

Important safety information

General safety summary

Terms in the manual

Terms on the product

Symbols on the product

Specifications

Vertical system analog channels

Horizontal and acquisition system

Trigger specifications